Cautions for handling
description
Transcript of Cautions for handling
![Page 1: Cautions for handling](https://reader038.fdocuments.net/reader038/viewer/2022102809/56814304550346895daf56ea/html5/thumbnails/1.jpg)
1
Cautions for handling• Store condition• Clean• Non-Humid• Place which is not exposed to direct sunshine• Air flow between the box and floor
![Page 2: Cautions for handling](https://reader038.fdocuments.net/reader038/viewer/2022102809/56814304550346895daf56ea/html5/thumbnails/2.jpg)
2
No Good !!
Untidy
Dusty
Humidity Sunshine
Danger
![Page 3: Cautions for handling](https://reader038.fdocuments.net/reader038/viewer/2022102809/56814304550346895daf56ea/html5/thumbnails/3.jpg)
3
Fitting a Bearing on the Shaft
Always press the ring to be fitted.
![Page 4: Cautions for handling](https://reader038.fdocuments.net/reader038/viewer/2022102809/56814304550346895daf56ea/html5/thumbnails/4.jpg)
4
Mounting
![Page 5: Cautions for handling](https://reader038.fdocuments.net/reader038/viewer/2022102809/56814304550346895daf56ea/html5/thumbnails/5.jpg)
5
Fitting a Bearing into a Housing
Always press on the ring to be fitted.
![Page 6: Cautions for handling](https://reader038.fdocuments.net/reader038/viewer/2022102809/56814304550346895daf56ea/html5/thumbnails/6.jpg)
6
Mounting
![Page 7: Cautions for handling](https://reader038.fdocuments.net/reader038/viewer/2022102809/56814304550346895daf56ea/html5/thumbnails/7.jpg)
7
Thermal Mounting
Under no circumstances should you heat a bearing
by directly putting the torch on the bearing surface.
• Use oven, hot plate, or NSK bearing induction heater
• Clean heating apparatus
• Exercise care when using hot oil bath
• Do not heat above 248 deg F (120 deg C)
• Reference inner ring expansion chart in NSK catalog, fig. 14.3
![Page 8: Cautions for handling](https://reader038.fdocuments.net/reader038/viewer/2022102809/56814304550346895daf56ea/html5/thumbnails/8.jpg)
8
• Precautions
– Make Sure Oil Is Free of Sludge
– Control Temperature, Do Not Overheat
– Keep Tank Covered When Not In
• Advantages
– Heat Large Heats Efficiently
– Safe For Bearing
• Disadvantages
– Oil Can Contaminate Bearing
– Heating Oil May Not Compatible with Lube
– Can Not Heat Sealed Bearings By This Method
Without using flames or oil uniform heating in short time is possible, making shrink fitting efficient and clean.
![Page 9: Cautions for handling](https://reader038.fdocuments.net/reader038/viewer/2022102809/56814304550346895daf56ea/html5/thumbnails/9.jpg)
9
Bearing Removal Procedures
• Mark position/orientation of bearing
• Remove very carefully to avoid damage to shaft/housing
• Use appropriate tools (not hammers)
• Apply pressure to the ring with the interference fit
![Page 10: Cautions for handling](https://reader038.fdocuments.net/reader038/viewer/2022102809/56814304550346895daf56ea/html5/thumbnails/10.jpg)
10
Dismounting
![Page 11: Cautions for handling](https://reader038.fdocuments.net/reader038/viewer/2022102809/56814304550346895daf56ea/html5/thumbnails/11.jpg)
11
Dismounting
![Page 12: Cautions for handling](https://reader038.fdocuments.net/reader038/viewer/2022102809/56814304550346895daf56ea/html5/thumbnails/12.jpg)
12
Dismounting by puller
![Page 13: Cautions for handling](https://reader038.fdocuments.net/reader038/viewer/2022102809/56814304550346895daf56ea/html5/thumbnails/13.jpg)
13
Misalignment
Misalignment due to the bearing
being mounted out of square.