CATALOGUE 2017 - Futurasmus KNX Group

cubiertas_a4THE BEST SELECTION OF KNX PRODUCTS
1 5 Y E A R S E X C L U S I V E L Y D E D I C A T E D T O T H E K N X S T A N D A R D
Futurasmus, S.L. is not responsible for the accuracy, nor for errors of any nature or omissions regarding the content of this catalogue. All information must be checked upon in our web site or with our technical or commercial staff. Furthermore, Futurasmus, S.L.reserves the right at any time to correct the content of the digital version of this catalogue and in future editions. All logos, images and trade marks belonging to third parts have been used with due regard to the rights of their lawful holders.
INDEX
04 KNX POWER SUPPLIES MDT · LINGG&JANKE · IPAS
06 TP LINE/AREA COUPLERS KNX BUS CABLE MDT · LINGG&JANKE · APRICUM · FABRICANTE CABLE BUS
08 PROGRAMMING DEVICES ARCUS · APRICUM · IPAS · WEINZIERL
10 ACTUATORS IPAS · INTERRA · LINGG&JANKE · MDT
14 UNIVERSAL DIMMING ACTUATORS BES · DINUY ·MDT · LINGG&JANKE
16 INPUTS MDT · INTERRA · LINGG&JANKE · ARCUS
18 DETECTORS BES · MDT · ZUBLIN · STEINEL
20 SENSORS ARCUS · ELSNER · BMS
40 SMART METERING LINGG&JANKE · ARCUS
44 VISUALIZATION IPAS · IDDERO · INTERRA · HOUSEINHAND · TCI
56 GATEWAYS HVAC, LON, BACNET, MODBUS AND ENOCEAN INTESIS
58 ROOM CONTROLLERS IDDERO · ARCUS · ELSNER · INTERRA · MDT · TENSE
62 PUSH BUTTONS MDT · LINGG&JANKE · EKINEX · INTERRA · TENSE · DAKANIMO · GEPRO IDDERO · ARCUS · ELSNER
KNX DEVICES CATALOGUE
LINGG&JANKE
160, 320 and 640mA KNX power supplies, all of them with auxiliary unfiltered output and status LEDs to indicate operation modus: normal, overload or reset.
IPAS
Very small KNX 640mA power supply (only 3 DIN rail units). It has an auxiliary unfiltered output and 3 status LEDs to indicate operation modus: normal, overload or reset.
MDT
160, 320, 640, 960 and 1280mA KNX power supplies. Note the uninterrupted KNX power supply: thanks to its two independent power supplies, offers high reliability (in case one of them fails).
| 05
Futurasmus KNX Group · KNX Devices Catalogue 2017
TP LINE/AREA COUPLERS KNX BUS CABLE
APRICUM
It can be used as either line or area coupler. With status LED and manual mode, that can be activated to temporarily modify the configuration of the filter table during the commissioning and diagnosis phase (without having to reprogram the coupler).
MDT
It can be used as either line or area coupler. With status LEDs and manual mode, that can be activated to temporarily modify the configuration of the filter table during the commissioning and diagnosis phase (without having to reprogram the coupler).
BUS CABLE MANUFACTURER:
Single pair (red/black) or two pairs KNX bus cable (red/black and yellow/white) with halogenfree or PVC sheath. Also available with 750V insulation.
LINGG&JANKE
It can be used as either line or area coupler. With status LEDs to test the proper operation of the coupler.
06 | KNX Devices Catalogue 2017 · Futurasmus KNX Group
| 07
PROGRAMMING DEVICES
IPAS
Both the KNX IP programmer (NCI) and the IP Router are equipped with an integrated web server for diagnostic functions (to show sent and received telegrams, connections used, etc.); up to 5 simuntaneous Tunnelling KNXnet/IP connections and 1 KNXnet/IP Object Server connection are allowed.
ARCUS
This router has both the functionality of KNXnet/IP Routing and KNXnet/IP Tunnelling connection. We can highlight the following features: group monitor via HTML, bus monitor, NTP time server, data logging in SD card and possibility to generate charts with the registered data, SSL to secure SSH/SFTP, etc.
WEINZIERL
Let us single out the USB programmer in stick format and also the DIN rail version, sized only 1 Unit. Also, their product range includes an RS.232 programmer and gateways with KNXnet/IP Routing or KNXnet/IP Tunnelling y Object Server functionality.
APRICUM
The USB programmer facilitates the bidirectional communication between the PC and the KNX TP bus. This devices stands out for its great pricequality ratio.
| 09
ACTUATORS
LINGG&JANKE
The ECO+ actuator range for DINrail mounting in centralized systems has now been improved and includes manual control for the same prize.
IPAS
This manufacturer offers 2 ranges of multifunction actuators: the μBricks, specially designed for decentralized systems (since they can be installed in electric cabinets or mounted on DIN rail) and the PowerBlocks, for DIN railmounted, centralized systems. Very advanced application program, including logic, timers, blocking functions, etc.
MDT
Complete actuator range both for DIN rain mounting and installation in wall boxes. As it happens with the rest of MDT devices, buttons for manual control have been improved. The same as all the MDT products, they have a 3year warranty.
INTERRA
Complete range of multifunction actuators for DIN railmounting in centralized systems. Apart from allowing control of 230VAC blinds/shutters and ON/OFF functions, they include fan coil and 24VDC blind/shutter control.
| 11
17296 77024-180-01 4U 270 9
14911 72130-180-04 4U/Flushmount 343 9
17297 77024-180-02 4U/Flushmount 397 9
14912 72130-180-05 4U 398 9
17171 ITR504-16A-01 6U 150 7
17172 ITR508-16A-02 6U 250 7
17173 ITR512-16A-02 10U 300 7
17174 ITR516-16A-01 10U 350 7
17175 ITR520-16A-01 15U 380 7
17176 ITR524-16A-01 15U 410 7
17423 A2F16H-E 3U 115 7
17429 J2F6H-E 3U 140 7
17424 A4F16H-E 4U 136 7
17430 J4F6H-E 4U 188 7
17433 BEA4FK16H-E 6U 158 7
17436 BEA4F230H-E 6U 158 7
6
6
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
YES
NO
NO
NO
NO
NO
NO
Measureme NT Size Listprice G.D.
NO17161 JAL-01UP.02 Wall box 99 7NO - 11 - 6 NO 1 NO
These columns indicate the maximum number of each function. The functions in multifunction actuators are combinable. Example: A multifunction actuator with 4 outputs can be used for (4 x On / Off) or (2 x Shutters) or (1 x Shutter and 2 x On / Off).
Futurasmus KNX Group · KNX Devices Catalogue 2017
NO16056 AZI-0316.01 4U 280 7NO 3 -3 - 20 200μF 1 Power
NO17163 JAL-0410.02 4U 238 7NO - 44 - 10 NO 2 NO
ACTUATORS
These columns indicate the maximum number of each function. The functions in multifunction actuators are combinable. Example: A multifunction actuator with 4 outputs can be used for (4 x On / Off) or (2 x Shutters) or (1 x Shutter and 2 x On / Off).
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
NO
17156 AKS-2016.03
17156 AKS-2016.03
20
16
200μF
140μF
1
1
Current
NO
Web Code Reference Multifunction On/Off* Blind*Outputs Fan Coil* I(A) CLoad Channelsper Phase InputsMeasureme NT Size Listprice G.D.
Futurasmus KNX Group · KNX Devices Catalogue 2017 | 13
Futurasmus KNX Group is currently selling to over 60 countries in the world We have offices in Spain, Germany, Southern Africa, Middle East and China..
Futurasmus KNX GROUP ESPAÑA C/ de la Nit. 1, Bloque 7, Local 1 03110 Mutxamel (Alicante) T: +34 965959511 F: +34 965959172 E: [email protected] www.futurasmus-knxgroup.es
Futurasmus GmbH KNX GROUP Audifaxstr. 7 75315 · Radolfzell · GERMANY T: +49 7732 802975 F: +49 7732 802974 E: [email protected] www.futurasmus-knxgroup.de
Futurasmus KNX GROUP CHINA Room 1-1503 · No.13a Beiyuan Road · Chaoyang Disctrict Beijing · P. R. CHINA T: +86 10 6025 8878 E: [email protected] www.futurasmus-knxgroup.cn
Futurasmus KNX GROUP SOUTH AFRICA 86 Marine Drive · Paarden Eiland 7405 · Cape Town (W-Cape) · SOUTH AFRICA T: +27 (0) 879437190 E: [email protected] www.futurasmus-knxgroup.co.za
Futurasmus KNX GROUP BAHRAIN P.O.Box 511 · Manama · Al Rossais Tower Off. 12· Bl. 283 · Rd 1704 · Dipl. Area 317 · BAHRAIN T: +973 39948072 F: +973 17910334 E: [email protected] www.futurasmus-me.com
UNIVERSAL DIMMING ACTUATORS
MDT
For dimming incandescent, halogen (standard or electronic transformer), low consumption lamps and LED at 230VAC with only 4W (minimum consumption needed for operation). A different version is also available for 1 10 V ballasts.
BES
For dimming incandescent, halogen (standard or electronic transformer), low consumption lamps. A special range designed for optimal LED regulation at 230VAC and avoid the blinking derived from dimming is available.
LINGG&JANKE
For dimming incandescent, halogen (standard or electronic transformer) and low consumption lamps. Their catalogue includes a dimmer specially designed for the regulation of LED lamps at 230VAC, which allows for a more precise dimming through selectors.
DINUY
| 15
INPUTS
LINGG&JANKE
Extensive selection of potentialfree inputs for DINrail or inwall mounting, as well as 230VAC, 8 – 48VDC inputs. Moreover, their catalogue includes a push button interface that gives great valueformoney.
MDT
Complete range of potentialfree inputs for DINrail or inwall mounting, as well as 230VAC, 1224VDC, 24VAC or analogue 012V/210V, 020mA/420mA inputs.
ARCUS
Analogue input for flush mounting that includes two 012VDC inputs.
INTERRA
Push button interface with 2, 4 or 6 inputs and great qualityprice ratio.
| 17
INPUTS
9739
9743
11521
11518
9745
9748
11519
9746
9749
17106
11520
9747
9750
16746
16747
Type
41x41x12mm
41x41x12mm
41x41x12mm
2U
4U
8U
2U
4U
8U
41x41x12mm
2U
4U
8U
41x41x12mm
41x41x12mm
Size
49
68
88
168
228
348
168
228
348
88
168
228
348
118
158
Listprice
7
7
7
7
7
7
7
7
7
7
7
7
7
5
5
17178
17179
17180
17299
17300
4365
4364
5668
14795
ITR102
ITR104
ITR106
TS4F-2-U
TS8F-2-U
BE9FK
BE9F24
BE9F230
SK08-AN2
2
4
6
4
8
9
9
9
2
DETECTORS
ZUBLIN
Infra red detectors for fitted installation in ceilings or walls, or else flush mounting. All their detectors are equipped with brightness sensor.
BES
This brand offers a series of infra red presence detectors, which stand out for being very small for ceiling installation. On top of that, they include a radio frequency detector for concealed mounting.
STEINEL
Among their main detectors, it is worth mentioning their IP45 outdoors detector, as well as their high frequency detector (specially designed for installation in corridors).
MDT
Infra red detectors for fitted installation in ceilings or wall mounting. Let us highlight their detector finished in glass. All their detectors are equipped with brightness sensor.
| 19
14679
14681
14680
12604
17338
17339
12715
12605
15374
15375
12389
12716
11041
11039
11040
11037
11038
DETECTORS
10629
10630
10631
10632
10633
(Mov. 6 - 10m) a 1,1m
(Mov. 6 - 10m) a 1,1m
(Mov. Ø11m, Presen. Ø5m) a 3m
(Mov. 14x5m) a 3m
Detection Range (X m. Height)
(Mov. Ø6m, Presen. Ø2m) a 1,1m
Ø36mm
Ø36mm
10634
10635
15883
15882
15884
15376
15926
25248
25249
004064
004057
004040
593711
002992
(Mov. Ø20m ) a 2m
(Mov. Ø20m ) a 2m
(Mov. Ø20m ) a 2m
(Presen. 4x4m) a 2,8m
(Presen. 3x10m) a 2,8m
Elsner
Arcus
Arcus
T-Objekt-UP Temperature sensor for flushmount blind cover
• Temperature measurement • 4 configurable temperature thresholds. • Sending of minimum and maximum registered temperature values. • PI thermostat for cooling and heating, PI or 2 point regulation for additional cooling and additional heating. • For flushmount installation, hidden under blind cover. • Measuring range: 40 ... +80º C
Web code Reference 8140 70178
SK03-T Temperature sensor, flushmount
• Temperature measurement • Upper temperature threshold • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostats for cooling and heating • Fits 55x55mm frames. • Measuring range: 25 ... +55º C
Web code Reference Colour 6075 30103201 White 6076 30103202 Black
ElsnerKNX T-UP Temperature sensor, flushmount, with optional push buttons and display
• Temperature measurement • 3 configurable temperature thresholds. • Sending of minimum and maximum registered temperature values. • PI thermostat for cooling and heating, PI or 2 point regulation for additional cooling and additional heating. • 2 PI (%) value comparators to calculate average and maximum or minimum values of up to 5 inputs. • The models fitted with display can show up to 3 information lines.
• The models fitted with push buttons allow manual setpoint temperature changes. • Fits 55x55mm frames. • Measuring range: 40 ... +80º C
Web code Reference Display Buttons Colour 14642 70350 NO NO White 14643 70351 NO NO Aluminium 14644 70352 NO NO Anthracite 14645 70353 NO NO Stainless Steel 15822 70354 YES NO White 15823 70355 YES NO Aluminium 15824 70356 YES NO Anthracite 15825 70357 YES NO Stainless Steel 15826 70358 YES YES White 15827 70359 YES YES Aluminium 15828 70360 YES YES Anthracite 15829 70361 YES YES Stainless Steel
SK30-TC Temperature sensor, flushmount, with push buttons or rotary control
• Temperature measurement • Setting of temperature limits • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat • Setpoint temp. variation via front buttons and/or communication objects • 2 potential free, binary inputs to configure as needed • Status LED • Fits 55x55mm frames. • Measuring range: 20 ... +80º C
Web code Reference Display Buttons Colour 14642 70350 NO NO White 14643 70351 NO NO Aluminium 14644 70352 NO NO Anthracite 14645 70353 NO NO Stainless Steel 15822 70354 YES NO White 15823 70355 YES NO Aluminium
SENSORS
• Temperature measurement • Upper temperature threshold • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostats for cooling and heating • Measuring range: 25 ... +55º C
ElsnerKNX T-AP Temperature sensor IP65 with probe
• Temperature measurement • 4 configurable temperature thresholds. • Sending of minimum and maximum registered temperature values. • PI thermostat for cooling and heating, PI or 2 point regulation for additional cooling and additional heating. • For flushmount installation, hidden under blind cover. Measuring range: 40 ... +80º C
ArcusSK08-T8 Controller for 8 PT1000 temperature probes, IP65
• 8 analogue inputs for PT1000 temperature probes (not included). For each input: • Temperature measurement • Upper and lower temperature thresholds. • 2 point, PI and PWM thermostat for cooling and heating. • Measuring range: 30….+180ºC • Protection rating IP65
ArcusSK01-T Temperature sensor IP65 without probe
• Temperature measurement • Upper temperature threshold • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostats for cooling and heating • Analogue input for PT1000 probe. • Protection rating IP65.
ArcusSK01-T-ATF2 Temperature sensor IP65 with probe
• Temperature measurement • Upper temperature threshold • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostats for cooling and heating • Measuring range: 50 ... +90º C • Protection rating IP65.
ArcusSK07-TC-6B Controller for PT1000 temperature probe, IP20
• Temperature measurement (PT1000 temperature probe not included) • Setting of temperature limits • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat • Setpoint temp. variation via front buttons and/or communication objects • 6 potential free, binary inputs to configure as needed • Measuring range: 20…+80ºC
SENSORS
ArcusSK01-T-OTFF IP65 temperature sensor with square contact probe for flat surfaces
• Temperature measurement • Upper temperature threshold • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat for cooling and heating. • Measuring range: 30 ... +105º C • Protection rating IP65.
ArcusSK01-T-HTF IP65 Temperature sensor with stainless steel V4A immersion probe
• Temperature measurement • Upper temperature threshold • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat for cooling and heating. • Protection rating IP65.
Web code Reference Measure r. IP probe Probe cable m. 6130 30101002 -30...+105°C 65 PVC 6112 30101003 -50...+180°C 65 Silicone 6131 30101055 -50...+250°C 68 Teflon
ArcusSK01-T-ALTF1 IP65 temperature sensor with axial contact probe for pipes and ducts
• Temperature measurement • Upper temperature threshold • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat for cooling and heating. • Protection rating IP65.
Web code Reference Measure r. Probe cable m. 6332 30101004 -35...+105°C PVC 9212 30101005 -35...+180°C Silicone
ArcusSK01-T-ALTF2 IP65 temperature sensor with contact probe for pipes and ducts
• Temperature measurement • Upper temperature threshold • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat for cooling and heating. • Measuring range: 30 ... +110º C • Protection rating IP65.
ArcusSK01-T-ETF1 IP65 Temperature sensor with probe within brass screwin mmersion stem
• Temperature measurement • Upper temperature threshold • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat for cooling and heating.
ArcusSK01-T-ESTF IP65 Temperature sensor with probe within steel V4A screwin immersion stem
• Temperature measurement • Upper temperature threshold • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat for cooling and heating. • With Ø 8 mm screwin, V4A steel probe that supports up to 40 bars • Protection rating IP65.
Web code Reference Measure r. Probe cable m. Probe size 10011 30101008 -35...+105°C PVC G1/2", 50mm 10012 30101009 -35...+105°C PVC G1/2", 100mm 10013 30101010 -50...+180°C Silicone G1/2", 50mm 10014 30101011 -50...+180°C Silicone G1/2", 100mm
ArcusSK01-T-ETF2 IP65 Temperature sensor with probe within steel V4A screwin immersion stem
• Temperature measurement • Upper temperature threshold • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat for cooling and heating. • Measuring range: 30….+150 ºC • With Ø 8 mm screwin, V4A steel probe that supports up to 40 bars • Protection rating IP65.
Web code Reference Probe size 6081 30101020 G1/2", 50mm 6134 30101021 G1/2", 100mm 6135 30101022 G1/2", 150mm 6136 30101023 G1/2", 200mm 6137 30101024 G1/2", 250mm 6138 30101025 G1/2", 300mm 6139 30101026 G1/2", 400mm
SENSORS
• With Ø 8 mm screwin, V4A steel probe that supports up to 40 bars • Protection rating IP65
SK01-T-ETF3 IP65 Temperature sensor with extended probe within steel V4A screwin immersion stem
• Temperature measurement • Upper temperature threshold • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat for cooling and heating. • Measuring range: 30….+150 ºC • With Ø 8 mm screwin, V4A steel probe that supports up to 40 bars • Protection rating IP65.
ArcusSK01-T-ETF7 IP65 Temperature sensor with quicktemperatureresponse probe within immersion stem
• Temperature measurement • Upper temperature threshold • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat for cooling and heating. • Measuring range: 30….+150ºC • Neck tube probe with quickresponse for measuring temperature in places with major temperature fluctuations in short periods of time. • Protection rating IP65.
Web code Reference Probe size 10002 30101034 G1/2", 100mm 10003 30101035 G1/2", 150mm 10004 30101036 G1/2", 250mm
Arcus
SENSORS
ArcusSK01-T-KTF1 IP65 temperature sensor with probe for air ducts
• Temperature measurement • Upper temperature threshold • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat for cooling and heating. • Measuring range: 30….+150ºC • Protection rating IP65.
ArcusSK01-T-RPTF1 IP65 temperature sensor with pendulum room probe
ArcusSK01-T-RPTF2 IP65 temperature sensor with pendulum black globe probe
ArcusSK30-TC-VOC Temperature and VOC (volatile organic compounds) sensor, fittedmount, with push buttonsor rotary control
• Temperature and VOC measurement • Setting of temperature limits • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat • Ventilation control according to the VOC values • Setpoint temp. variation via front buttons and/or communication objects • 2 potential free, binary inputs to configure as needed • Status LED • Fits 55x55mm frames. • Temperature measuring range: 20…+80ºC • VOC measuring range: 45…2000 ppm
Web code Reference Buttons Rotary control Colour 16612 30513361 NO NO White 16613 30513362 NO NO Dark grey 16616 30513371 YES NO White 16617 30513372 YES NO Dark grey 16614 30513351 NO YES White 16615 30513352 NO YES Dark grey
SENSORS
KNX TH-UP Temperature and humidity sensor, flushmount, with optional push buttons and display
• Measurement of temperature, relative humidity, absolute humidity and dew point • 4 configurable temperature thresholds. • 2 configurable humidity thresholds. • Dew point threshold. • Sending of minimum and maximum registered temperature values. • Sending of minimum and maximum registered humidity values. • PI thermostat for cooling and heating, and 2 point regulation for additional cooling and additional heating. • PI regulation for humidification and dehumidification. • The models fitted with display can show up to 3 information lines. • The models fitted with push buttons allow manual setpoint temperature changes. • Fits 55x55mm frames. • Temperature measuring range: 40 ... +100º C • Humidity measuring range: 0 ... 100 %
Web code Reference Display Buttons Colour 15831 70362 NO NO White 15832 70363 NO NO Aluminium 15833 70364 NO NO Anthracite 15834 70365 NO NO Stainless Steel 15835 70366 YES NO White 15836 70367 YES NO Aluminium 15837 70368 YES NO Anthracite 15838 70369 YES NO Stainless Steel 15839 70370 YES YES White 15840 70374 YES YES Aluminium 15841 70375 YES YES Anthracite 15842 70376 YES YES Stainless Steel
ArcusArcusSK30-TC-CO2 Temperature and CO2 sensor, flushmount, with push buttons or rotary control
• Temperature and CO2 measurement • Setting of temperature limits • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat • Ventilation control according to the CO2 values • Setpoint temp. variation via front buttons and/or communication objects • 2 potential free, binary inputs to configure as needed • Status LED • Fits 55x55mm frames. • Temperature measuring range: 20…+80ºC • CO2 measuring range: 45…2000 ppm
ArcusSK03-TFK Temperature and humidity sensor, flushmount
• Measurement of temperature, relative humidity, absolute humidity, dew point and enthalpy • Upper temperature threshold • Upper and lower relative humidity thresholds. • Dew point alarm • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat for cooling and heating. • 2 point regulation of relative humidity • Fits 55x55mm frames. • Temperature measuring range: 25…+55ºC • Humidity measuring range: 10…90%
SENSORS
ArcusNeo-TC Temperature and humidity sensor, flush-mount
• Measurement of temperature, relative humidity, absolute humidity, dew point and enthalpy • Upper temperature threshold • Upper and lower relative and absolute humidity thresholds. • Sending of minimum and maximum registered temperature values. • Binary inputs + Additional functions • Temperature measuring range: -20 ... +80 ° C • Protection rating IP65. Aluminum enclosure
Web code Reference Colour 17878 30511583 Squared, brushed aluminum 17879 30511584 Squared, brushed black aluminum 17880 30511683 Rounded, brushed aluminum 17881 30511684 Rounded, brushed black aluminum
ArcusSK30-THC Temperature and humidity sensor, flushmount, with push buttons or rotary control
• Measurement of temperature, relative humidity, absolute humidity, dew point and enthalpy • Setting of temperature and humidity limits • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat • Setpoint temp. variation via front buttons and/or communication objects • 2 potential free, binary inputs to configure as needed • Status LED • Fits 55x55mm frames. • Temperature measuring range: 20…+80ºC • Humidity measuring range: 0…95%
ArcusSK02-TFK Temperature and humidity sensor, surface mount
• Measurement of temperature, relative humidity, absolute humidity, dew point and enthalpy • Upper temperature threshold • Upper and lower relative humidity thresholds. • Dew point alarm • Sending of minimum and maximum registered temperature values. • 2 point thermostat for relative humidity • Temperature measuring range: 25…+55ºC • Humidity measuring range: 10… 90%
ElsnerCala KNX TH Temperature and humidity sensor, flushmount, with display
• Measurement of temperature, relative and absolute humidity • Upper and lower relative temperature thresholds. • Sending of minimum and maximum registered temperature values. • Receiving and processing data from the KNX bus • 4 analogic/digital inputs + Additional functions • Temperature measuring range: -20 ... +70 ° C • Protection rating: IP20 • For 55x55mm frames installations
Web code Reference Colour 17676 70602 Black 18161 70607 White
SENSORS
SK01-TFK-RPFF IP65 temperature and humidity sensor with pendulum room probe
• Measurement of temperature, relative humidity, absolute humidity, dew point and enthalpy • Upper temperature threshold • Upper and lower relative humidity thresholds. • Dew point alarm • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat for cooling and heating. • 2 point thermostat for relative humidity • Temperature measuring range: 20…+80ºC • Humidity measuring range: 10…100% • Protection rating IP65.
Web code Reference Protection against 10015 30301054 Dust 10016 30301056 Dust and condensation
ArcusArcus
SK01-TFK-KFF IP65 temperature and humidity sensor with probe for air ducts
Arcus
SK01-TFK-AFF IP65 Temperature and humidity sensor with probe
ElsnerTH65-AP IP65 Temperature and humidity sensor with probe
• Measurement of temperature, relative humidity, absolute humidity, dew point and enthalpy • 4 configurable temperature thresholds. • 2 configurable humidity thresholds. • Dew point threshold • Sending of minimum and maximum registered temperature values. • Sending of minimum and maximum registered humidity values. • PI thermostat for cooling and heating, PI or 2 point regulation for additional cooling and additional heating. • PI regulation for humidification and dehumidification. • Temperature measuring range: 40…+80ºC • Humidity measuring range: 0… 100% • Protection rating IP65.
SENSORS
ArcusSK07-THC-4B Controller for SHT11 temperature and humidity probe, IP20
• Temperature and humidity measurement • Setting of temperature and humidity limits • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat • Setpoint temp. variation via front buttons and/or communication objects • 4 potential free, binary inputs to configure as needed • Inputs for SHT11 temperature and humidity probe (not included) • Measuring range: 20…+80ºC • Humidity measuring range: 0...95%
ArcusSK30-THC-VOC Temperature, humidity and VOC (volatile organic compounds) sensor, fittedmount, with push buttons or rotary control
• Measurement of temperature, relative humidity, absolute humidity, dew point, enthalpy and VOC • Setting of temperature and VOC limits • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat • Ventilation control according to the VOC values • Setpoint temp. variation via front buttons and/or communication objects • 2 potential free, binary inputs to configure as needed • Status LED • Fits 55x55mm frames. • Temperature measuring range: 20..+80ºC • Humidity measuring range: 0…+95% • VOC measuring range: 450…2000 ppm
ArcusSK30-THC-CO2 Temperature, humidity and CO2 sensor, flushmount, with push buttons or rotary control
• Measurement of temperature, relative humidity, absolute humidity, dew point, enthalpy and CO2 • Setting of temperature and CO2 limits • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat • Ventilation control according to the CO2 values • Setpoint temp. variation via front buttons and/or communication objects • 2 potential free, binary inputs to configure as needed • Status LED • Fits 55x55mm frames. • Temperature measuring range: 20..+80ºC • Humidity measuring range: 0…+95% • CO2 measuring range: 0…2000 ppm
ArcusSK03-TTFK Temperature and humidity sensor with probe and input for additional PT1000 probe, flushmount
• Measurement of temperature, temperature of the additional PT1000 probe (not included), relative humidity, absolute humidity, dew point and enthalpy. • Upper temperature threshold • Upper and lower relative humidity thresholds. • Dew point alarm • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat for cooling and heating. • 2 point regulation of relative humidity • According to the temperature of the additional PT1000 probe (not included):
SENSORS
• Temperature measuring range: 20… + 80ºC • Humidity measuring range: 0..95%
SK30-TTHC-VOC Temperature, humidity and VOC (volatile organic compounds) sensor and input for PT1000 probe, fittedmount, with push buttons or rotary control
• Measurement of temperature, relative humidity, absolute humidity, dew point, enthalpy and VOC • Setting of temperature and VOC limits • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat • Ventilation control according to the VOC values • Setpoint temp. variation via front buttons and/or communication objects • 2 potential free, binary inputs to configure as needed • Status LED • Fits 55x55mm frames. • Temperature measuring range: 20..+80ºC • Humidity measuring range: 0…+95% • VOC measuring range: 450…2000 ppm
Arcus
• 2 point thermostat for heating; or 2 point regulation of the dew temperature. • Temperature measuring range: 20… + 80ºC • Humidity measuring range: 0..95%
ArcusSK07-TTHC-4B Controller for SHT11 temperature and humidity probe, IP20 and input for PT1000 probe, fittedmount
• Temperature and humidity measurement • Sending of minimum/maximum registered temperature values. • Termostato 2 puntos, PI y PWM • Setpoint temp. variation via front buttons and/or communication objects • 4 potential free, binary inputs to configure as needed • According to the temperature of the additional PT1000 probe (not included) • Temperature measuring range: 20..+80ºC • Humidity measuring range: 0…+95%
ArcusSK30-TTHC Temperature and humidity sensor, fitted - mount, with push buttons or rotary control and input for control rotativo
• Measurement of temperature, relative humidity, absolute humidity, dew point and enthalpy • Upper and lower temperature limits setting up • Envío del valor mínimo y máximo de temperatura registrados • 2 point, PI and PWM thermostat • Setpoint temp. variation via front buttons and/or communication • 2 potential free, binary inputs to configure as needed • According to the temperature of the additional PT1000 probe (not included) • Status LED • Fits 55x55mm frames.
ArcusSK01-TTFK-AFF IP65 Temperature and humidity sensor with probe and input for additional PT1000 probe
• Measurement of temperature, temperature of the additional PT1000 probe (not included), relative humidity, absolute humidity, dew point and enthalpy. • Upper temperature threshold • Upper and lower relative humidity thresholds. • Dew point alarm • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat for cooling and heating. • 2 point regulation of relative humidity
SENSORS
ArcusSK30-TTHC-CO2 Sensor de temperatura , humedad, CO2 y entrada para sonda PT1000 , instalación empotrada, con botones o control rotativo
• Measurement of temperature, relative humidity, absolute humidity, dew point, enthalpy and CO2 • Setting of temperature and CO2 limits • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat • Ventilation control according to the CO2 values • Setpoint temp. variation via front buttons and/or communication objects • 2 potential free, binary inputs to configure as needed • Input for additional PT1000 temperature probe • Status LED • Fits 55x55mm frames. • Temperature measuring range: 20..+80ºC • Humidity measuring range: 0…+95% • CO2 measuring range: 0…2000 ppm
• According to the temperature of the additional PT1000 probe (not included): • 2 point thermostat for heating; or 2 point regulation of the dew temperature. • Temperature measuring range: 20… + 80ºC • Humidity measuring range: 10..90% • Protection rating IP65.
ArcusSK01-TTFK-RPFF IP65 Temperature and humidity sensor with pendulum room probe and input for additional PT1000 probe
• Measurement of temperature, temperature of the additional PT1000 probe (not included), relative humidity, absolute humidity, dew point and enthalpy. • Upper temperature threshold • Upper and lower relative humidity thresholds. • Dew point alarm • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat for cooling and heating. • 2 point regulation of relative humidity • According to the temperature of the additional PT1000 probe (not included): • 2 point thermostat for heating; or 2 point regulation of the dew temperature. • Temperature measuring range: 20… + 80ºC • Humidity measuring range: 10..100% • Protection rating IP65.
Web code Reference Protection against 10046 30401054 Dust 10047 30401056 Dust and condensation
SENSORS
Web code Reference Colour 11339 70246 Anthracite 11340 70247 Stainless Steel
KNX AQS/TH-UP Temperature, humidity and CO2 sensor, flushmount, with optional push buttons and display
• Measurement of temperature, relative humidity, absolute humidity, dew point and CO2. • 3 configurable temperature thresholds. • 2 configurable humidity thresholds. • 4 configurable CO2 thresholds. • Dew point threshold. • Sending of minimum and maximum registered temperature values. • Sending of minimum and maximum registered humidity values. • Sending of maximum registered CO2 value. • PI thermostat for cooling and heating, and 2 point regulation for additional cooling and additional heating. • PI regulation for humidification and dehumidification. • 2stages CO2 PI regulation • 2 PI (%) value comparators to calculate average and maximum or minimum values of up to 5 inputs. • The models fitted with display can show up to 3 information lines. • The models fitted with push buttons allow manual setpoint temperature changes. They can also be configured for switching, regulation, shutter/blinds, scenes, etc. • Fits 55x55mm frames. • Temperature measuring range: 10 ... +50ºC • Humidity measuring range: 0 ... 95 % • CO2 measuring range: 0 ... 2000 ppm
Web code Reference Display Buttons Colour 10780 70234 NO NO White 10781 70235 NO NO Aluminium 10782 70236 NO NO Anthracite 10783 70237 NO NO Stainless Steel 10784 70239 YES YES White 10785 70240 YES YES Aluminium 10786 70241 YES YES Anthracite 10787 70242 YES YES Stainless Steel
Elsner
ElsnerKNX AQS CO2 sensor, flushmount, with optional push buttons and display
• Measurement of CO2 • 4 configurable CO2 thresholds. • Sending of maximum registered CO2 value • 2stages CO2 PI regulation • 2 PI (%) value comparators to calculate average and maximum or minimum values of up to 5 inputs • The models fitted with display can show up to 3 information lines. • The models fitted with push buttons allow their fee configuration for either switching, regulating, shutter/blinds, scenes, etc. • Fits 55x55mm frames. • CO2 measuring range: 0…2000 ppm
Web code Reference Display Buttons Colour 10772 70224 NO NO White 10773 70225 NO NO Aluminium 10774 70226 NO NO Anthracite 10775 70227 NO NO Stainless Steel 10776 70229 YES YES White 10777 70230 YES YES Aluminium 10778 70231 YES YES Anthracite 10779 70232 YES YES Stainless Steel
ElsnerKNX VOC-UP VOC (volatile organic compounds) mixed gas sensor, flushmount
• VOC measurement • 4 configurable VOC thresholds • Sending of maximum registered VOC value • 2stages VOC PI regulation • 2 PI (%) value comparators to calculate average and maximum or minimum values of up to 5 inputs • Fits 55x55mm frames. • VOC measuring range: 450…5000 ppm • Additional 1224V DC power supply required.
Web code Reference Colour 11337 70244 White 11338 70245 Aluminium
SENSORS
ArcusNeo-TC-CO2 Temperature, humidity and CO2 sensor, flush-mount
• Measurement of temperature, relative humidity, absolute humidity, dew point and enthalpy • Upper temperature threshold • Sending of maximum registered CO2 value. • Upper and lower relative and absolute humidity thresholds. • Sending of minimum and maximum registered temperature values. • Binary inputs + Additional functions • Temperature measuring range: -20 ... +80 ° C • Protection rating IP65. Aluminum enclosure
Web code Reference Colour 17882 30512563 Square, brushed aluminum 17883 30512564 Square, brushed black aluminum 17884 30512663 Rounded, brushed aluminum 17885 30512664 Rounded, brushed black aluminum
ElsnerCala KNX AQS/TH Temperature, humidity and CO2 sensor, flushmount, with display
• Measurement of temperature, relative and absolute humidity and CO2 • Upper and lower relative temperature thresholds. • Sending of minimum and maximum registered temperature values. • Measurement CO2 range: 0 to 2000 ppm • Receiving and processing data from the KNX bus • 4 analogic/digital inputs + Additional functions • Temperature measuring range: -20 ... +70 ° C • Protection rating: IP20 • For 55x55mm frames installations
Web code Reference Colour 17677 70603 Black 18163 70608 White
SENSORS
• Sensor range for measuring temperature and/or humidity and/or brightness (in 3 directions) and/or atmospheric pressure and/or CO2 • Configurable thresholds. • Installation in ceiling
Web code Reference Movement Temperature Humidity Brightness At. pressure CO2 17072 70392 NO YES NO NO NO NO 17073 70393 NO YES YES NO NO NO 17074 70394 NO NO NO NO NO YES 17075 70395 NO NO NO YES NO NO 17076 70396 YES NO NO YES NO NO 17077 70397 NO YES YES NO YES YES 17079 70398 YES YES YES NO YES NO 17080 70399 YES YES YES YES YES YES
SALVA KNX Fire detector
• Smoke and/or fire detector • Audio signal • 9V battery for voltage failure included • Temperature measuring range: 10…+50ºC • Humidity measuring range: 0 ... 90 % • PI thermostat for cooling and heating, and 2 point regulation for additional cooling andadditional heating (advanced function). • PI regulation for humidification and dehumidification (advanced function).
Web code Reference Smoke Fire Temperature Humidity Advanced functions 17446 70404 YES YES YES YES YES 17447 70405 YES NO NO NO NO
Quadra Weather Station
• Measurement of temperature, wind, wind direction, brightness (independent values for north, east, south, west and skywards), global radiation (independent values for north, east, south, west and skywards), twilight and precipitation. • Sun position calculation. • Advanced functions via sun areas, weekly schedules and the analysis of the registered values. • Protection rating IPX4. • Additional 2128V DC power supply required.
Web code Reference 13507 Quadra
BMSElsner
Elsner
• Measurement of temperature, wind, brightness, twilight and precipitation. • 4 configurable temperature thresholds. • 3 configurable wind thresholds. • 3 configurable brightness thresholds. • 3 configurable twilight thresholds. • Sending of minimum and maximum registered temperature values. • Sending of maximum registered wind value. • Protection rating IP44. • Additional power supply required.
Web code Reference Additional power supply 5667 3095 230VAC 6117 3096 24VDC (20VAC)
Elsner
• Measurement of temperature, wind, brightness, twilight and precipitation. • Obtains the position, date and current time from the GPS signal. • Sun position calculation. • 4 configurable temperature thresholds. • 3 configurable wind thresholds. • 3 configurable brightness thresholds.
Elsner
SENSORS
ElsnerSUNTRACER KNX SL LIGHT Weather Station with integrated GPS receiver and facade control
• Measurement of temperature, wind, brightness, twilight and precipitation. • Obtains the position, date and current time from the GPS signal. • Sun position calculation. • Configurable thresholds. • Weekly and annual time switches. • Automatic control of up to 5 independent façades. • Protection rating IP44. • Additional 1240V DC (1228V AC) power supply required.
ElsnerSUNTRACER KNX SL Weather Station with integrated GPS receiver and facade control
• Measurement of temperature, wind, brightness, twilight, precipitation and atmospheric pressure. • Obtains the position, date and current time from the GPS signal. • Sun position calculation. • Configurable thresholds. • Weekly and annual time switches. • Automatic control of up to 8 independent façades. • Protection rating IP44. • Additional 1240V DC (1228V AC) power supply required.
ElsnerSK01-GPS-TC Temperature and brightness sensor with integrated GPS receiver, IP65
• Temperature and humidity measurement • Obtains the position, date and current time from the GPS signal. • Astronomic time. • Time switch. • Protection rating IP65.
• 3 configurable twilight thresholds. • 5 configurable sun areas. • Sending of minimum and maximum registered temperature values. • Sending of maximum registered wind value. • Weekly and annual time switches. • Protection rating IP44. • Additional 1240V DC (1228V AC) power supply required.
Web code Reference Additional power supply 9032 3094 12…40V DC (12…28V AC)
ElsnerSUNTRACER KNX-GPS Weather Station with integrated GPS receiver and facade control
• Measurement of temperature, wind, brightness, twilight and precipitation. • Obtains the position, date and current time from the GPS signal. • Sun position calculation. • 4 configurable temperature thresholds. • 3 configurable wind thresholds. • 3 configurable brightness thresholds. • 3 configurable twilight thresholds. • Sending of minimum and maximum registered temperature values. • Sending of maximum registered wind value. • Weekly and annual time switches. • Automatic control of up to 6 independent façades. • Protection rating IP44. • Additional 1240V DC (1228V AC) power supply required.
ElsnerSUNTRACER KNX SL BASIC Weather Station
• Measurement of temperature, wind, brightness (in 3 directions), twilight and precipitation. • Configurable thresholds. • Protection rating IP44. • Additional 1240V DC (1228V AC) power supply required.
SENSORS
• 2 point, PI and PWM thermostat • Setpoint temp. variation via front buttons and/or communication objects • Input for PT1000 temperature probe • Temperature measuring range: 20…+80ºC • Humidity measuring range: 0…+95ºC • Brightness measuring range: 3…220.000 lux
KNX SENSOR Weather sensor
• Sensor range for measuring wind and/or precipitation and/or brightness • 3 configurable thresholds • Sending of maximum registered wind value. • Protection rating IP44. • Additional power supply required.
Web code Reference Wind Precip. Bright. Add.power supply 6040 70122 YES NO NO 230VAC 6041 70123 YES NO NO 24VDC (20VAC) 6042 70124 NO YES NO 230VAC 6043 70125 NO YES NO 24VDC (20VAC) 6044 70199 NO NO YES NO 6045 70126 YES YES NO 230VAC 6046 70127 YES YES NO 24VDC (20VAC) 6047 70128 YES NO YES 230VAC 6048 70129 YES NO YES 24VDC (20VAC)
Elsner
ArcusSK10L-TC-L Brightness sensor and input for additional PT1000 temperature probe, IP65
• Brightmess measurement • Setting of temperature limits • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat • Setpoint temp. variation via front buttons and/or communication objects • Input for PT1000 temperature probe • Temperature measuring range: 20…+80ºC • Brightness measuring range: 3…220.000 lux
Vari KNX Weather sensor
• Sensor range for measuring temperature and/or humidity and/or brightness (in 3 directions) and/or atmospheric pressure and/or GPS. • Configurable thresholds. • Protection rating IP44.
Elsner
ArcusSK10L-THC-L-AFF Temperature, humidity and brightness sensor, IP65
• Measurement of temperature, relative humidity, absolute humidity, dew point, enthalpy and brightness • Setting of temperature and humidity limits • Sending of minimum and maximum registered temperature values. • 2 point, PI and PWM thermostat • Setpoint temp. variation via front buttons and/or communication objects • Input for PT1000 temperature probe • Temperature measuring range: 20…+80ºC • Brightness measuring range: 3…220.000 lux
ArcusSK10L-TTHC-L-AFF Temperature, humidity and brightness sensor and input for PT1000 temperature probe, IP65
• Measurement of temperature, relative humidity, absolute humidity, dew point, enthalpy and brightness • Setting of temperature and humidity limits • Sending of minimum and maximum registered temperature values.
Web code Reference Temperature Humidity Brightness Atmosph. press. GPS 15818 70385 YES NO NO NO NO 15803 70382 NO NO YES NO NO
SENSORS
ElsnerKNX PY Global radiation sensor, IP44
• Measurement of global radiation value • 4 configurable global radiation thresholds. • Sending of maximum registered global radiation value. • Measurement range of global radiation: 0 ... 2500 W/m2 • Protection rating IP44.
ElsnerSK08-BFT-WMT Soil temperature and moisture sensor, IP65
• Measurement of soil temperature, soil moisture (in hPa), relative humidity, absolute humidity and dew point. • Upper and lower temperature thresholds. • Upper and lower soil moisture thresholds. • Upper and lower relative humidity thresholds. • Upper and lower absolute humidity thresholds. • Upper and lower dew point thresholds. • 2 point, PI and PWM thermostat. • 2 point, PI and PWM soil moisture regulation. • 2 point, PI and PWM relative humidity regulation. • Soil temperature and humidity probe included. • The model that supports an additional PT1000 probe (not included), also measures that probe's temperature; upper and lower threshold and 2 point, PI and PWM regulation. • Measurement range of soil temperature: 20... +80º C • Measurement range of soil moisture: 1…2000 hPa/mbar, • 1200.000 Pa • Protection rating IP65.
Web code Reference Additional temperature probe accepted 9169 30805001 NO 10023 30805021 YES
Web code Reference Temperature Humidity Brightness Atmosph. press. GPS 15816 70383 YES NO YES NO NO 15819 70386 YES YES NO NO NO 15817 70384 YES YES YES NO NO 15820 70388 YES YES NO YES NO 15821 70389 YES YES YES YES NO 15864 70387 NO NO NO NO YES
ElsnerKNX SENSOR SL Weather sensor
• Sensor range for measuring wind and/or precipitation and/or brightness • Protection rating IP44. • Additional 1240V DC (1228V AC) power supply required.
Web code Reference Wind Precipitation Brightness 15798 70158 YES NO NO 15799 70159 NO YES NO 15800 70162 YES YES NO 15801 70164 YES NO YES
ArcusSK08-GLBS-MES Global radiation sensor, IP65
• Measurement of global radiation level • Upper and lower global radiation thresholds. • 2 point, PI and PWM global radiation regulation. • Global radiation probe included • Measurement range of global radiation: 0 ... 1800 W/m2 • Spectral range: 400... 1100 nm • Protection rating IP65.
SENSORS
• Additional 912V DC power supply required (included).
SO250 basic Ultrasonic filllevel sensor (depth gauge)
• Measurement of the filllevel (in litre, m3 or %) or fillhight (in m) or distance to filllevel (in m) • 5 configurable thresholds in cm, litres, m3 or %. • Measuring range: 12 ... 250 cm • Size: 3 DIN mod.
Elsner
• Up to 4 probes accepted (not included) For each input: • Temperature and relative humidity measurement • 2 configurable temperature thresholds. • 2 configurable humidity thresholds. • Sending of minimum and maximum registered temperature values. • Sending of minimum and maximum registered humidity values. • Additional 230V AC power supply required. • Size: 6 DIN mod.
ElsnerKNX TH-ERD Probe for soil temperature and moisture sensor KNX I4ERD
• Protection rating IP68.
ArcusX-S8-F Ultrasonic filllevel sensor (depth gauge)
• Measurement of the filllevel (in litre or m3), fillhight (in m, dm, cm or mm), distance to filllevel (in m, dm, cm or mm) and fill percentage • Upper and lower filllevel thresholds • Upper and lower fillhight thresholds • Upper and lower distance to filllevel thresholds • Upper and lower fill percentage thresholds • 2 point filllevel regulation • 2 point fillhight regulation • 2 point distancetofilllevel regulation • 2 point fill percentage regulation • Protection rating IP65.
SO250 Ultrasonic filllevel sensor (depth gauge)
• Measurement of the filllevel (in litre, m3 or %) or fillhight (in m) or distance to filllevel (in m) • 5 configurable thresholds in cm, litres, m3 or %. • 2 relays that can be configured via own display and push buttons. • Measuring range: 12 ... 250 cm • Additional 230V AC power supply required. • Size: 7 DIN mod.
Elsner
Web code Reference Installation IP rating Measuring range Size 10282 30807001 Surface 65 0,15 … 2,5 m - 10699 30807002 DIN rail 20 0,15 … 2,5 m 2 units 10692 30807011 Surface 65 0,75 … 6 m - 10698 30807012 DIN rail 20 0,75 … 6m 2 units
SENSORS
ArcusSK08-WAQ-MES Water Quality Sensor IP65
• Measurement of pH level, ORP (redox/reduction potential) and water temperature. • Runhour counter. • Upper and lower pH thresholds. • Upper and lower ORP thresholds. • Upper and lower temperature thresholds. • Upper and lower runhour thresholds (as electrode calibration alert). • 2 point, PI and PWM pH regulation. • 2 point, PI and PWM ORP regulation. • Both electrodes included. • Temperature measuring range: 0 ... +50º C • Protection rating IP65.
15Th Anniversary as a KNX wholesaler and KNX++ training centre
ARCUS
LINGG&JANKE
They deliver real energy (kWh and Wh), power (W), current (A), voltage (V) and power factor values. Available for threephase and singlephase measurement, as well as for direct measurement or via toroidal transformer. Additional invoicing functionality, resettable relative counters, etc.
LINGG&JANKE
They deliver water consumption values, as well as more advanced functions, such as thresholds, relative counters, etc. Available with different nominal diameters and flows. Feel free to ask our commercial staff for specialsized counters.
ENERGY COUNTERS
LINGG&JANKE ARCUS
The Arcus counters deliver thermal energy values, whereas the Lingg&Janke counters deliver both thermal energy and cooling values. Both devices include advanced functions. Feel free to ask our commercial staff for specialsized counters.
LINGG&JANKE
They deliver the accumulated gas consumption in m3 and litre; with advanced functions, such as relative counters, invoicing, etc. Feel free to ask our commercial staff for specialsized counters.

CALORIES/FREEZERIES COUNTERS
IpasCBSE ComBridge Studio Evolution
Visualization software preinstalled in an industrial embedded Linux PC. Also available as a virtual machine. Available in different hardware versions to match the requirements of any type of installation: from small homes to offices, hotels, airports (SCADAlike/BMS), etc.
• Flashbased web visualization for PCs or touch displays • Fully customizable user interface: background, icons, text, colours, charts, frames, resolution, etc. • Browsing based on desktops, windows, pages and gadgets • Exporting of HTML pages for smart phones and tablets • User rights and management • It allows simultaneous connection to different independent installations from one visualization • A KNXnet/IP Tunnelling or KNXnet/IP Object Server gateway is required to connect each installation • Unlimited group addresses • Weekly and annual time scheduler • Scenes allow the introduction of delays between actions • Alarm notification in the visualization • Sending of alarms via email • Logic module with graphic editor, including logic gates, timers, arithmetic operations, comparators, etc. • Data logger • Customizable charts • Basic energy monitoring (for a full metering solution, the Smart Metering module is needed) • DALI module for the visualization and maintenance of systems equipped with DALI gateways (by IPAS) • Alarms with SMS notification via VoIP systems and even push notifications in IOS/Android (using thirdparty software) • Management modules for BACnet, Modbus and OPC gateways • Data export and remote back ups • Remote management of systems that are independent from each other. Each one controls its own scenes, alarms, etc. (with additional license) • Virtual data points based on historic data. Access to historic data via SQL commands • License for 3 users included • License for 1 gateway included • 12V DC power supply required (PSU included).
Web Code Reference Version 10019 63102-32-01 Server 13816 63102-32-05 Server Avanced 13905 63102-32-04 Server Avanced Racksystem
VISUALIZATION
IpasCBSE CBSE extension modules
Web Code Reference Description 10616 63102-32-50 5 additional users 10693 63102-32-51 5 additional gateways 10681 63102-32-10 Smart Metering module (up to 5 counters) 10382 63102-32-52 5 additional counters 14793 63102-32-12 Modbus module (up to 5 devices) 13770 63102-32-55 5 additional Modbus devices 15788 63102-32-13 BACnet module (up to 5 devices) 15790 63102-32-54 5 additional BACnet devices 15791 63102-32-60 Report module 13307 63102-32-30 Data base management module 15792 63102-32-11 DALI management module 15793 63102-32-53 5 additional DALI gateways
VISUALIZATION
IpasHCC HomeControl Center
The web server integrated in the device hosts the HTML visualization. No plugins, like flash or java, needed, which makes it compatible with any web browser of any device in the market (PC, smart phone, tablet, etc.)
• 3 different visualizations in HTML: 1. Totally customizable visualization 2. Visualization adapted for SMART PHONE format 3. Visualization adapted for TABLET format • Fully customizable user interface: background, icons, text, colours, frames, resolution, etc. • Smart Visu: special visualization mode for smart phones based on icons; it automatically adapts to any given resolution. • 250 communication objects and also 1000 group addresses that are independent from the former. • Chart module with up to 10 series per chart, with or without data interpolation and polling function with read requests to the bus. Possibility to send data via email in XML format by means of an event from the KNX bus. • Monitoring module to register and save data from communication objects and group addresses. Configurable as blacklist and whitelist. Possibility to send data via email in XML format by means of a telegram event from the KNX bus. • TCP/UDP Commands module, for sending commands to IP devices with events from the KNX bus. Compatible with PJLink protocol for the control of film projectors. • Acoustic alarms and sending of emails with the alarms log as an attachment. • Annual and weekly time scheduler, that can be edited by the final user. • Real time clock with NTP timer server synchronization, that can be used as KNX date/time master. • Logic module with graphic editor, including logic gates, timers, arithmetic operations, comparators, etc. • Scenes allow the introduction of delays between actions • Alarm notification in the visualization. • Sending of alarms via email • KNXnet/IP Tunnelling functionality: allows using the device as an IP programmer for the ETS. • Integrated BCU • Additional power supply required: 1230VDC • Size: 4 DIN mod.
Web Code Reference 11066 3622-141-11
VISUALIZATION
IdderoHC1i-KNX 5.7" Touch Display with integrated web server
Touch displays with simple and userfriendly visualization and control interface. Its hardware has been designed to achieve maximum reliability and a fast performance without delays.
• 5.7" TFT LED Colour touch display • Integrated web server to replicate the display's visualization in HTML format, compatible with any device (PC, tablet, smart phone, etc.) • Thermostat functionality (external temperature probe required) • Its user interface has been completely redesigned to ensure an innovative and fresh appearance, optimizing previous looks • Including a renewed set of over 230 icons • Graphic navigation via customizable sensitive areas (i.e, on floor plans) • Scenes editable by final users, including the introduction of delays between actions • Weekly time switches with annual periods • Alarm monitoring with historical data • Presence simulation with day/night timetable • Logic functions (logic gates, comparators, time switches, arithmetic calculations, etc.) • Email notifications on KNX events • KNX time master to send date/time to the bus • Compatible with the idderocloud service for remote access • Integrated BCU • 12V DC power supply required (PSU included).
Web Code Reference Colour of the frame 13772 DW-HC1i-KNX-G Grey 13773 DW-HC1i-KNX-W White 13774 DW-HC1i-KNX-B Matt black 13775 DW-HC1i-KNX-A Anodized aluminium
VISUALIZATION
IdderoHC2-KNX 7" Touch Display with integrated web server
In addition to the functionality of the 5,7" HC1KNX version, it has:
• 7" TFT LED Colour panoramic touch display • Integration of IP cameras* • Videodoor communication function, with full duplex audio and echo cancellation*.
* Please, check compatibility with our commercial staff
Web Code Reference Colour of the frame 10043 DW-HC2-KNX-G Grey 11164 DW-HC2-KNX-G White 11163 DW-HC2-KNX-B Matt black 10044 DW-HC2-KNX-A Anodized aluminium
VISUALIZATION
IdderoHC2L-KNX 10" Touch Display with integrated web server
In addition to the functionality of the 5,7" HC1KNX version, it has:
• 10" TFT LED Colour panoramic touch display • Integration of IP cameras* • Videodoor communication function, with full duplex audio and echo cancellation*.
Web Code Reference Colour of the frame 10315 DW-HC2L-KNX-G Grey 11166 DW-HC2L-KNX-W White 11165 DW-HC2L-KNX-B Matt black 11167 DW-HC2L-KNX-A Anodized aluminium
VISUALIZATION
IdderoDW-GSM GSM expansion module for Iddero devices
KNX system control and status alarms via SMS messaging and missed calls
• Connection to a HC1iKNX, HC2KNX, HC2LKNX touch display or Iddero Home Server required • Remote scene execution • Control of the devices integrated in the KNX installation • Status request via messaging • "Missed call" functionality to avoid costs on most frequent actions • 12 V DC power supply required. • Size: 6 DIN mod.
Web Code Reference 9592 DW-GSM
VISUALIZATION
IdderoSER1-KNX Iddero Home Server
Same HTML visualization as in the HC1iKNX, HC2KNX y HC2LKNX touch display's web servers
• Integrated web server with visualization in HTML format, compatible with any device (PC, tablet, smart phone, etc.) • 8 freeconfigurable binary inputs, 4 of which can also be used to connect temperature probes • Thermostat functionality (external temperature probe required) • Its user interface has been completely redesigned to ensure an innovative and fresh appearance, optimizing previous looks • Including a renewed set of over 230 icons • Graphic navigation via customizable sensitive areas (i.e, on floor plans) • Scenes editable by final users, including the introduction of delays between actions • Weekly time switches with annual periods • Alarm monitoring with historical data • Presence simulation with day/night timetable • Logic functions (logic gates, comparators, time switches, arithmetic calculations, etc.) • Email notifications on KNX events • KNX time master to send date/time to the bus • Compatible with the idderocloud service for remote access • Ethernet connection • Integrated BCU • 12V DC power supply required (PSU included) • Size: 6 DIN mod.
Web Code Reference 13771 DW-SER1-KNX
VISUALIZATION
InterraTR-107-0104 7" Touch Display with integrated web server
Touch display with exceptional design and wide functionality for home control. • 7" LCD colour touch display • Mobile APP available for iOS and Android to acquire the full configuration of the display via reading of QR codes • Alarm monitoring with historical data • Caretaker services, traffic information, wheather news, RSS news, etc. • Integration of IP cameras* • Thanks to its camera, microphone and two speakers, it can also be used as indoor intercom system. • Videodoor communication function* • Several frames available (black aluminium, black acrylic, stailess steel)* • 12 V DC power supply required.
Web Code Reference 17440 ITR-107-0104
VISUALIZATION
InterraITR-110-0104 10.1" Touch Display with integrated web server
Touch display with exceptional design and wide functionality for home control. • 10.1" LCD colour touch display • Mobile APP available for iOS and Android to acquire the full configuration of the display via reading of QR codes • Alarm monitoring with historical data • Caretaker services, traffic information, wheather news, RSS news, etc. • Integration of IP cameras* • Thanks to its camera, microphone and two speakers, it can also be used as indoor intercom system. • Videodoor communication function* • Several frames available (black aluminium, black acrylic, stailess steel)* • 12 V DC power supply required.
VISUALIZATION
HouseinhandHOUSEINHAND HOUSEINHAND Licenses
App for smart phones and tables, available both for iOS and Android.
• Simple and clear userinterface, very easy to use • Customizable backgrounds • Scenes (the final user might create new scenes from the App itself) • Videodoor communication function compatible with TCS system, from Jung • Integration of IP cameras* • Integration of IRTrans and Global Cache • KNXnet/IP Tunnelling gateway required for KNX connection
Web Code Reference Description 13285 HIH2_BP BASIC license for 2 devices 13286 HIH2_PP PREMIUM license for an unlimited number of devices 13287 HIH2_UB2P BASIC to PREMIUM license upgrade
VISUALIZATION
TCILuna16 Kit 16" Capacitive multitouch display for homeautomation applications
Touch display with embedded PC for the installation of any visualization and control software
• 16” TFT multitouch display, colour, 1366x768 • AMD Fusion Dual Core 2x1.0GHz • 2 GB RAM • Speaker and handsfree microphone • SSD hard drive • Ethernet • RS232 • USB • Windows 10 • Mounting box included • 24V DC power supply required (PSU included)
* Contact our commercial staff for different type of mounting or size
Web Code Reference 15787 luna16
GATEWAYS HVAC, LON, BACNET, MODBUS AND ENOCEAN

8214
Device Web Code For
ME-AC-KNX-15/100
Bidirectional
AG150A/ GB50ADA
DK-AC-KNX-1i
10952
DK-RC-KNX-1
9539
DK-RC-KNX-1i
PA-AC-KNX-64/128
12171/12172
Bidirectional Full control
Device Web Code For
DK-AC-KNX-1i
10952
PA-RC2-KNX-1i
12961
PA-AW-KNX-1
13792
A.W. indoor units
AK-AC-KNX-4/8/16/64
Bidirectional
Bidirectional
GATEWAYS HVAC, LON, BACNET, MODBUS AND ENOCEAN

Device Web Code For
SM-AC-KNX-4/8/16/64/128
Bidirectional
TO-RC-KNX-1i
13419
A.C. Indoor units
TO-AC-KNX-16/64
Bidirectional
MH-RC-KNX-1i
11168
MH-AC-KNX-48/128
Bidirectional
215 x 170 x 65 mm
IBOX-KNX-MBRTU
Bidirectional
KNX TP Modbus EIA232
Bidirectional
KNX TP
Modbus Ethernet
Bidirectional
KNX TP
Bidirectional
IBOX-KNX-LON
Bidirectional
KNX TP
Bidirectional
system
ROOM CONTROLLERS
Iddero
Elsner
VERSO 4.3" Touch Display with integrated BCU and 2 independent thermostats
Stylish and compactsized room controller with crystal front, suitable for all types of environments and decoration.
• Capacitive colour Touch Display 4,3''' • 48 functions that can be freely arranged among 6 control pages • Additional “favourites” page, that allows the final user to select up to 8 functions • Different colour themes available and possibility to customize background images • Time schedules, alarm monitoring, internal scenes controller • Two independent 2 point, PI and PWM thermostats for cooling, heating, additional cooling and additional heating • Integrated temperature probe • 4 multifunction inputs • Integrated BCU • Additional 1230V DC power supply required
Web Code Reference Colour of the frame 17329 DW-VERSO-W Blanco 17330 DW-VERSO-B Black
ArcusTouch IT Smart 3.5" Touch Display with integrated BCU and thermostat
• Colour Touch Display 3,5''' • Manufactured in aluminium • 48 functions that can be freely arranged among 6 control pages • 2 point, PI and PWM thermostat for cooling, heating, additional cooling and additional heating. • Integrated temperature probe • Alarm management module with acoustic signal • Weekly time schedules that can be edited by the end user • Line and bar graphs (microSD required) • Log of KNX telegrams (microSD required) • Integrated BCU • Additional 932V DC power supply required.
Web Code Reference Colour of the frame 12376 22310500 Aluminium 12381 22310501 White 12382 22310504 Black
Corlo Touch 3.5" Touch Display with integrated BCU and thermostat
• Colour Touch Display 3,5''' • Proximity sensor • Brightness sensor • PI thermostat for cooling and heating, PI or 2 point regulation for additional cooling and additional heating. • 4 potentialfree binary inputs available; they can be connected to temperature sensors. • Engraved text inscriptions or customized logos available, with RGB backlighting * • Fits Corlo frame range. • Integrated BCU • Additional 1224V DC power supply required.
* Please, contact our commercial staff
Web Code Reference Colour 12301 70259 Brilliant black 12300 70258 White brilliant 12303 70261 Matt black 12302 70260 Matt white
ElsnerCorlo Touch WL 3.5" Touch Display with integrated BCU and thermostat
In addition to the Corlo Touch functionality, also:
• Integrated WiFi • Integration of IP cameras* • Web page display • Remote control from smart phones and tablets
ROOM CONTROLLERS
Web Code Reference Colour 12305 70253 Brilliant black 12304 70252 White brilliant 12307 70255 Matt black 12306 70254 Matt white
ElsnerCorlo Touch KNX 5IN (WL) Touch Display 5” integrated BCU and thermostat
• 5 "touch color display • Proximity sensor • Brightness sensor • Thermostat PI for cold and heat and PI or 2 points for additional cold and additional heat. • 4 free potential binary inputs suitable for temperature probes. • 5 automatic channels, ventilation, shading, climate control and light. • Controller of 16 scenes • Time switches, alarm clock • WiFi Interface (WL model only) • Web browser (WL model only) • IP cameras display (WL model only) * • Allows remote control from Smartphone and Tablets (WL model only)
* Check compatibility
Web Code Reference WiFi Add.Functions Colour 18207 70481 No No Black 18207 70475 Yes Yes Black
InterraImini 6.5" Touch Display with integrated BCU and thermostat
• Colour Touch Display 6,5''' • Thanks to its camera, microphone and speaker, it can also be used as intercom system • Temperature sensor • Brightness sensor • 2 IR sensors (infrared) • Integrated BCU vAdditional 12V DC power supply required
MDTSCN-RT1G Thermostat with integrated BCU and LCD
• Glass capacitive thermostat, black or white • 4 sensitive areas: 2 for the thermostat and 2 for free configuration • 2 point, PI and PWM thermostat for cooling, heating and additional heating. • Integrated BCU
Web Code Reference Colour 14800 SCN-RT1GW.01 White 14799 SCN-RT1GS.01 Black
MDTSCN-LCDG Thermostat with integrated BCU and LCD
• Glass capacitive thermostat, black or white • 4 sensitive areas. • 20 freely configurable functions via LCD. • 2 point, PI and PWM thermostat for cooling, heating and additional heating. • Integrated BCU
Web Code Reference Colour 14796 SCN-LCDGW.01 White 14798 SCN-LCDGS.01 Black
Futurasmus KNX Group, multibrand wholesaler of KNX devices.
ABB ALTENBURGER
BAB TEC BERKER
Futurasmus KNX Test Lab
Test Lab accredited by the KNXA to do the conformity and interoperability tests of the application programs of new KNX devices.
Consulting and training for new developers.
www.futurasmus-knxlab.es
PUSH BUTTONS
MDT BE-TG
MDT BE-TA
PUSH BUTTONS
MDT BE-GT
MDT SCN
IPAS BRACHETTO
IPAS PIAZZA
PUSH BUTTONS
IPAS LARGHO
IPAS CONTRATTEMPO
PUSH BUTTONS
PUSH BUTTONS
PUSH BUTTONS
PUSH BUTTONS
PUSH BUTTONS
DAKANIMO KAMEREON
GEPRO KNX4
PUSH BUTTONS
PUSH BUTTONS
OPTIONS TO MAKE YOUR PURCHASES OF KNX DEVICES IN FUTURASMUS
· Traditional procedure as a wholesaler:
· Personal commercial support to select the KNX devices you need · Purchase confirmation per email or fax · Usual market payment methods adapted to the needs of your compan · Also, online, nonbinding quotations via: www.futurasmusknxgroup.com
· Order processing online tool for registered clients:
· Only for registered clients (freelances or companies) · Fast and easy, including online personal account for shipment tracking · Advance payment (bank transfer or credit card) · Additional discounts in all your purchases to be redeemed in your next order
And, of course, allways the best technical supportss.

CATALOGUE 2017 - Futurasmus KNX Group

Documents

Transcript of CATALOGUE 2017 - Futurasmus KNX Group