Catalogue 2004 - Micronix Plus | Termoviziune - Aparate ... · PDF fileCatalogue 2004. SPECIAL...

DIG

ITAL PA

NEL M

ETER, TRASM

ITTER CATA

LOG

UE　

2004

Catalogue 2004

SPECIAL SCALING RANGE CODE

Range

1V

1B

1T

2A

2B

2T

Input Display

0 to (100 to 1999) one point fixed


±1999 to ±1999 one point fixed



±1999 to ±1999 one point fixed

1 to 5V

Voltage (from 0V)

Voltage

4 to 20mA

Current (from 0mA)

Current

*1V, 2A Except process monitor 1V and 2A*Need additional cost for the above ranges

URL http://www.asahikeiki. co. jpE-mail:dpm-overseas@asahikeiki. co. jp

COMPANY PROFILE

ASAHI KEIKI CO.,LTD. was established in 1950 as amanufactuer of industrial measuring instruments.We have since expanded into digital panel meters,intelligent meters and bimetallic thermostats.Rapid changes in electronic technoligy keeps us atthe forefront of these product areas.We constantly strive to meet customer's demands forerver higher quality and reliability.

ASAHI KEIKI CO.,LTD. Head Office :33-6, YAGUCHI 2-CHOME,

OHTA-KU,TOKYO 146-8505, JAPAN Telephone :(03)3759-3893 Fax :(03)3757-2989 Establishment :Sept, 1950 Capital :¥ 50,000,000.–

1

DC Voltmeter and Ammeters

Setpoint Comparator

AP-101 13page1/8 DIN Size

Low Cost

A5000 15page AP-141 16page1/8 DIN Size

Low Cost

AP-201A 19page 1/32 DIN Size

Low Cost

AP-244A21page1/32 DIN Size

BCD output

AP-30125pageThin case

Low Cost

AP-501A 26page 1/8 DIN Size

Thin case, Low cost

AP-520A 28page1/8 DIN Size

LCD, Low cost


AH-331 31pageopen case

AM-147 37page1/8 DIN Size

RS-232C

AM-215 35page 1/32 DIN Size Two setpoint

A5000 49page

AMH-762 44page1/8 DIN Size

High Conversion

2


Average

A5000 49page

AC Voltmeter and Ammeters

A5000 59page

Strain Gauge

AS-203A 51page1/32 DIN Size

Low cost

AL-501A 53page1/8 DIN Size

LCD, Two-wire

AL-512 55page1/8 DIN Size

LED, Two-wire

AT-205 58page1/32 DIN Size

TC, RTD

Thermo Meter

Process Monitor

A5000 57page

A7000 series 61page

NEWUniversal Type


A6000 series 64page

NEW

ASG-251 60page1/32 DIN Size

A5000 17page

3

TZ-5A 87pageRTD

TH-1X 79pageslim size

TZ-41 86pageSelf power

TW-2X 75page2 output

TZ-5H 84pageDC V,A

TW-3M 74pageProgramable

Transmitter

TZ-1D 71pageAC Power SupplyCT

TZ-1B 70pageAC Power SupplyPotentiometer

TZ-1X 69pageAC Power SupplyDC V,A

NEW NEW NEW

TZ-1F 73pageAC Power SupplyDC V,A (Small)

TZ-1E 72pageAC Power SupplyPT

NEW NEW

4

TABLE OF CONTENTTable of Contents..................................................................................................................4,5Explanation..........................................................................................................................6~8Applications ......................................................................................................................9~11Application Examples ............................................................................................................12

DC Voltmeter & Ammeter

AP-101 3 1/2 Digit V,A ............................................................................................13AP-102 3 1/2 Digit V,A, BCD ..................................................................................14

A5000 4 Digit V, A ................................................................................................15AP-141 4 1/2 Digit V ..............................................................................................16AP-142 4 1/2 Digit V, BCD ......................................................................................17AP-200 3 1/2 Digit V, 1/32 DIN ..............................................................................18AP-201A 3 1/2 Digit V, 1/32 DIN ..............................................................................19AP-202A 3 1/2 Digit V,A, 1/32 DIN, BCD ..................................................................20AP-244A 4 1/2 Digit V, 1/32 DIN, BCD......................................................................21AP-301 3 1/2 Digit V, Thin case ..............................................................................25AP-501A 3 1/2 Digit V, Thin case ..............................................................................26AP-502 3 1/2 Digit V, A ..........................................................................................27AP-520A 3 1/2 Digit V, LCD ......................................................................................28AP-540 3 1/2 Digit V,A ............................................................................................29AH-330, 331 3 1/2 Digit V, open case ............................................................................31AH-381 3 1/2 Digit V, LCD, open case ..................................................................32

A7000 series ..........................................................................................................................61 A6000 series ..........................................................................................................................64

Comparator (Meter Relay)

AM-123 4 Digit, Two setpoint ..................................................................................33AM-213 4 Digit, Two setpoint ..................................................................................34AM-215 4 Digit, 1/32 DIN, Two setpoint ............................................................35,36AM-147 4 Digit, RS-232C ..................................................................................37,38AM-749 4 1/2 Digit, Four setpoint, RS-485, RS-232C ........................................39,40AMH-752 3 1/2 Digit, High Conversion rate (4000/sec) ......................................41~43AMH-762 4 Digit, High Conversion rate (4000/sec) ............................................44~46

A7000 series ..........................................................................................................................61 A6000 series ..........................................................................................................................64

AC Voltmeter & Ammeter

AP-166 4 Digit, Average ........................................................................................47AP-560 3 Digit, Line Monitor ..................................................................................48

A5000 4 Digit, TRUE-RMS ....................................................................................49 A7000 series ..........................................................................................................................61 A6000 series ..........................................................................................................................64

Process Monitor (1 to 5V, 4-20mA, etc)

AS-101 3 1/2 Digit, A,V ..........................................................................................50AS-203A 3 1/2 Digit, A,V 1/32 DIN ............................................................................51AS-201 3 1/2 Digit, V 1/32 DIN ..............................................................................52AL-501A 3 1/2 Digit, A, Two-wire, LCD ....................................................................53AL-213 3 1/2 Digit, A, Two-wire, LED, 1/32 DIN ....................................................54AL-512 3 1/2 Digit, A, Two-wire, LED ....................................................................55AS-243 4 Digit, A,V ................................................................................................56

A7000 series ..........................................................................................................................61 A6000 series ..........................................................................................................................64

5

Thermometer

A5000 Sensor K,J,T,S,B,R,PT-100Ω......................................................................57AT-205 Sensor K,J,PT-100Ω, 1/32 DIN ..................................................................58

A7000 series ..........................................................................................................................61 A6000 series ..........................................................................................................................64

Strain Gauge Meter

A5000 4 Digit ........................................................................................................59ASG-251 3 1/2 Digit 1/32 DIN ..................................................................................60

A7000 series....................................................................................................................61~63 A6000 series ..........................................................................................................................64

Transmitter

TZ-1X DC V,A AC Power Supply ..........................................................................69 TZ-1B Potentiometer AC Power Supply................................................................70 TZ-1D CT AC Power Supply ................................................................................71 TZ-1E PT AC Power Supply..................................................................................72 TZ-1F DC V,A (Small) AC Power Supply ..............................................................73

TW-3M DC V,A ......................................................................................................74TW-2X DC V,A (2 output) ......................................................................................75TW-2XA DC V,A (2 output) AC Power Supply..........................................................76TW-2C TC, RTD......................................................................................................77TW-3R Alarm setter ................................................................................................78TH-1X DC V,A ......................................................................................................79TH-1C TC, RTD......................................................................................................80TH-41 Two-wire (2ch) ..........................................................................................81TH-1M DC V,A ......................................................................................................82TZ-5L Distributor ..................................................................................................83TZ-5H DC V,A ......................................................................................................84TZ-5X DC V,A ......................................................................................................85TZ-41 Two-wire ....................................................................................................86TZ-5A RTD ..........................................................................................................87TZ-5B Potentiometer ............................................................................................88TZ-5C TC ..............................................................................................................89TZ-5D AC, A..........................................................................................................90TZ-5E AC, V ..........................................................................................................91TZ-5F DC, A,V ......................................................................................................92

Accessories ..............................................................................................................93,94

New Model

ASAHI KEIKI CO.,LTD.6

OUTLINE

Digital panel meters are commonly used for various displays in awide range of equipment and analog-to-digital conversion in highlyadvanced control systems due to recent progress in highly accuratedigital measurement.

Digital panel meters (DPMs) have wide applications and come invarious types suitable to many application specifications, and differfrom digital multi-meters (D.M.M) in that they are used especially forsingle function, single range measurement.

Recently, a digital meter relay consisting of a digital panel meterwith a comparison function using digital switches has beendeveloped, thereby enabling not only the reading of normal values,but also the comparison of large, medium and small values.

Recent progress in electronics, especially in transistor technologyhas been remarkable, and the progressive development of ICs, LSIsand ultra LSIs, has greatly facilitated the transmission of informationand the emergence of a highly advanced information society.

The small size and low cost of DPMs is a result of innovations insemiconductor technology and has led to the widespreadreplacement of analog indicators as part of industry's move toautomate equipment and reduce labor costs.

DPMs provide a high level of measurement accuracy impossiblewith analog instruments and have an added advantage in that theycan be accurately and unambiguously read at a glance. In addition,DPMs have a system output function which converts analog signalsfrom sensors to digital signals for direct input to equipment such ascomputers, recorders and computing units to facilitate recording andautomatic control.

Asahi Keiki can provide a number of digital panel meters to meet awide range of applications through reliable design and quality controlbased on long experience with digital techniques. This is supportedby extensive and rigorous past production testing which is part of ourquality-assurance control system using standards that are directlytraceable to National standards. This quality assurance system isbacked by an equally extensive and experienced after sales service.

METER SELECTION

1. Applications1) For display only

For reading of general instruments2) For control of systems provided with system BCD input.

2. Measured signals1) Voltage/current2) DC/AC

3. No. of display digitsCurrently, 3 1/2 (1999), 4 (9999) and 4 1/2 (19999) digits areavailable. Resolution defined in terms of what division in % of fullscale is necessary to be read.For example, the resolution of a DPM displaying 1.999V is 1mV.

4. Measuring rangeThis ranges from µV minimum to V maximum as required. For example, if the number of digits and the voltage valuecorresponding to the least significant digit such as ±199.9mV or±1.9999V are determined, the measuring range is also determined.

5. AccuracyThe maximum error guaranteed by the manufacturer is calledaccracy. For example, ±0.15% rdg. ±1 digit for 3 1/2 digits or±0.03% rdg ±1 digit for 4 1/2 digits. The latter means that the errorof thedisplayedvalue 19999 is within ±7 digits and that of thedisplayed value 10000 is within ±4 digits.

6. Measuring SpeedThe speed required depends on the measured object and may notbe very important when the DPM is used only for display. However,an increase in speed in the entire measuring system results inimproved efficiency and labor savings, and it should be noted thatan increase in measuring speed reduces the time needed tointegrate (averaging) the input signal to bring about signal changeand fluctuated display with the signal change. Therefore, it isnecessary to select speed in accordance with applications.

7. Power Supply1) AC 90 to 132V and 180 to 264V selectable, 50/60Hz2) DC 5V ±5%, Mostly uses stabilized power3) DC 24V ±10% or 20%4) DC 12V ±10%

8. Input type1) Floating input

Input terminals are all isolated from the external case, powersupply and output circuit as is most desirable for systemapplications.Photo-couplers, pulse transformers and relays are used asisolators. In addition, this type can have a large common moderejection ratio (CMR). The AC power drive display only andsystem application DPM (with parallel BCD output) belongs tothis type.

2) Non-floating input2-1 Input with isolated common point

One input terminal is connected to one output terminal, but,it is isolated from the external case and power supply.

2-2 Input with common point and one power supply terminalOne input terminal is connected to one power supplyterminal.The DC 5V driven display-only DPM belongs to this type.From the above different standpoints, the following types areavailable.1) Single ended input2) Differential inputThe former has 2 terminals, Hi and Lo, but the latter canmeasure the signal between 2 input terminals regardless ofthe voltage applied to each input terminal and the commonpoint, which is similar to a differential OP amplifier.Therefore, this type completely differs from the floating inputtype in that measurement is impossible if the common pointis not used, being of the 3-terminal type. This type haslarge CMR to further increase the common mode rejectioneffect.

9. Input impedance and bias currentDPM input impedance is usually more than 100Mｽ, (excludingDPMs with an attenuator for an input range of more thanｱ 2V),but this is the ratio between input voltage change and input currentchange.Current close to the constant current, called bias current, also flowsthrough the input circuit and therefore, if there is high resistance inthe signal source, a voltage drop is produced across the resistancewhich is added to measured voltage as an error. Therefore,attention should be paid to the bias current according to the circuitused.

DIGITAL PANEL METEREXPLANATION

ASAHI KEIKI CO.,LTD. 7

CAUTIONS

1. Prior to operating the digital panel meter, carefully read the

instruction Manual.

2. Environment where the meter is used.1) It is desirable that meter be used under the normal room

temperature from 0 to 50｡C and relative humidity of 80% or less.The temperature is the most important factor exerting aninfluence upon meter reliability. Therefore, use the meter underthe normal room temperature as much as possible. Absolutelyavoid dew condensation caused by rapid temperature change.

2) Pay attention to not applying vibration and shock to the meter.3) Use the meter where no dust, chemicals and gases harmful to its

electronic components exist.

3. Storage

For long storage, avoid direct rays of the sun and store in atemperature from -10 to +70°C and relative humidity of 60% or less. Itis desirable that the meter be packaged in the same manner as thatdone prior to shipment.

4. Noise1) Power supply circuit

The digital panel meter driven by AC power may be influencedby electric noise entering through the power line. A capacitorfor noise prevention is inserted between the line on the primaryside of a power transformer.However, it is actually impossible to build a perfect noiseprevention circuit in such a small device as a DPM. Therefore, ifpower relays, magnet switches and/or high frequency devicesare connected to the same power line and/or abnormal voltagecaused by lightning etc., may be generated in the line, externallyconnect a line filter, varistor or noise absorption circuit.

2) ShieldThe circuit in the digital meter is protected from electrostaticinduction by the employment of a shielded case andelectrostatic shielded terminals of the power transformer.Therefore, if any problem occurs due to noise, connect thecommon terminal E to the ground or equipment groundingterminal.If any problem caused buy space induction may occur, groundthe metal case. For a molded case, is it effective when it iscovered with a metal case which most be grounded.

5. Handling of measuring input lineThe input impedance of the digital meter is very high in value of

1Mｽ to 100Mｽ so that the meter may influenced by induction noisedepending on its surroundings.1) Use a shielded 2-Conductor wire for the input line.2) Connect a RC filter in the input line.

However, pay attention that response time may become longerdepending on RC time constants.

6. Handling of system output line1) Bundling of wires

In general, the data output from the digital meter is a T.T.L ICwith latch, and no consideration for real data transmission is paidat all.Since it has the signal source impedance of several K%Ω, Theproximity of large current power line, relay and magnet switchcircuits to the output line may cause a malfunction due toelectromagnetic induction caused by electrostatic induction andmagnetic field induced by surge voltage and/or current pulses.may shorten meter life. Therefore, the output wires should be

bundled independent form other wires and to be wired apartfrom the power line as much as possible.

2) Length of transmission lineThe length of transmission line may have to be changeddepending on noise around the meter and surroundings.2-1 Direct transmission of output line: 2 m or less2-2 Transmission when a buffer circuit is used for each bit of

output line: 50 m or less2-3 Transmission when an isolator such as a photocoupler or

mercury relay is used for each bit of output line: 500 m or less

Caution: The above lengths are only for your reference. Therefore, the actual length must be determineddepending on each application.



1. High DC voltage measurementWhen voltage exceeding the maximum voltage in the standardrange is measured (for example: more than 200 V), a multiplier isconnected externally.

2. High AC voltage measurementWhen voltage exceeding the maximum voltage in the standardrange is measured (for example: more than 200 V), a multiplier orpotential transformer (PT) is connected externally.

* For the multiplier: Same as 1. High DC voltage measurement.

3. Large DC current measurementWhen large DC current exceeding 2A is measured, a shunt isconnected externally.

4. Large AC current measurementWhen AC current exceeding 0.4 A to 2 A is measured, a currenttransformer (CT) is connected externally.

5. Combination with printerWhen the BCD output of the digital panel meter is printed out andrecorded using digital printer.

6. Combination with recorderWhen the analog output of the digital meter is recorded using arecorder (pen writing recorder).

7. Combination with BCD display unitWhen the BCD output of the digital panel meter is connected to aBCD display unit for remote display.

8. Combination with converter

When each sensor output is connected to a converterwhich converts the output to 4 to 20 mA, 1 to 5 V or

any other voltage or current and also appropriatescaling is made to the digital panel meter, the meterwidens its applications to thermometer, pressuremeter, tachometer, etc. In addition, input isolationand level conversion are enabled when the digitalpanel meter is combined with an isolated converter.


ASAHI KEIKI CO.,LTD.

APPLICATIONS

9

Measuring mixing volumes of materials in tanks.

The ASG-157 series digital panel meter supplies power to load cells, subtracts tare weight and also has a built-in output circuit, thereby enabling the measurement of weight at low-cost.The ASG-157 together with load cells helps you make an appropriate mixed liquid by measuring the weight of each of two different chemicals.

Detecting warping of printed circuit boards.

Using the 2-input (A and B channels) computing function.The AMH-762 series digital panel meter applies analog signals from laser displacement sensors installed above two points on the board to its A and B channels, thereby detecting a warp of the board by computing (A-B).

Measuring and evaluating press fitting of parts used for precision machinery.

The peak hold function of the A5000 is used to check and then evaluate parts which are press-fitted to cylinder blocks, etc.

Helping you control rolling.

Our digital panel meters can help you control the rolling process by, measuring the number of roller revolution and also the moving distance of a specific roller in the vertical direction.The AC-963A displays the number of roller revolutions and outputs alarm signals together with a rotary encoder coupled to the shaft of that roller. In addition, the AM-123 inputs the output signal of an eddy current sensor to display the moving distance of the roller and also to output acoustic alarm signals as well as visual alarm signals with changes in display colors.

Measuring distortion of round bodies and eccentricity of shaft.

The peak valley hold function of the A5000together with a laser displacement or eddy current sensor is used to measure irregularity of round shaped bodies or bending of shafts.

Detecting, measuring and then evaluating the length of lead wires extending from capacitors.

Using the 2-input (A and B channels) computing function.The AMH-762 applies sensor detection signals to its A and B channels.It helps you inspect the cutting length of lead wires extending from capacitors by using its (A—B) function.It compares, evaluates and then outputs the computation result at a high sampling speed of 1000 times/sec.In addition, it can also obtain the maximum and minimum of any computed value by using its peak hold and valley hold functions.

A5000

A5000

A5000

AM-123

AMH-762

AMH-762


APPLICATIONS

10

Helping you inspect the condition of riveting, etc.

The AMH-752 can store severd/ satisfactory patterns of riveting by using its pattern select function. It can store eight types of high/high, high, low and low/low set points, hysteresis values and eight types of scaling values by using its pattern select function.As the allowable range can be instantly changed by the front switch or pattern selection from the rear terminal board, the meter can be conveniently used in any line where two or more different riveting materials exist.

Detecting warping of door glass by a differential transformer.

A sensor power supply is built in the meter. The AM-147, AM-749 or AM-213 has a built-in power supply of 12V or 24V DC for an external device. Therefore, it can be easily connected to a warping sensor with a built-in amplifier. It its direct setling function is used, it can easily set HH, HI, Lo and LL values used for evaluating a warp from measures data detected by the sensor.

Evaluation at high speed in high-speed mode.

Evaluating the clearance of piston rings at high speed.The AMH-762 can evaluate measured data at a speed of 4000 times/sec by the successive A/D conversion method. It can be conveniently used in any environment where inspection time is short.

Helping you process foods and control the process.

The front panel of the meter can be washed as the case is in dust proof and waterproof construction.The AT-216, AT-213, AC-221 and AC-281 conform to the IP66 standard.These meters are most suitable for use in an environment where temperature, pressure, weight, etc. Are measured in the HACCP process control.

Outputting digital signals to peripheral equipment.

Used as a converter with the display function which outputs digital signals to its peripheral equipment in BCD or RC 232C. The RS232 or BCD output function can be selected for all meters.It our digital panel meter is used as a converter whose signal is input to sequencers or personal computers, it can display and check actual input parameters, therefore, it is used conveniently for calibration.

Two or more measured values are multi dropped by RS485.

Contributing to saving the number of output wires.There are many digital panel meters with the output of RS485 in the lineup.Up to 30 meters including one host computer (31 in total) can be connected with two signal wires used, the address set to each meter and an RS485 - to - RW232C converter connected. In addition. If the dedicated "DIGIPANE485" software is used, collected data can be tabulated or graphically displayed.

AM-147

A5000

AT-216

AMH-762

AMH-762

A5000A5000 AM-749

RS485 - to - RW232CConverter(Commercially available)

A7000


APPLICATIONS

11

There meter sizes are selectable for easily accommodating meters in racks.

Din sizes of 96 mm (W) × 48 mm (H), 72mm (W) × 36 mm (H) and 48 mm (W) × 24mm (H)There are three meter sizes available so that any meter size which satisfies its accommodating space is selectable depending on the application.In addition to these three sizes, the cases of the901 series large display and SP-501A this type (35mm deep) digital panel meters are designed in consideration of their mounting environments.

Inspecting the greased condition of precision parts.

Inspecting the presence or absence of grease.The AS-105 has built-in 24V DC power supply, scaling function and analog comparator. It can configure inspection systems at low cost.

A5000

Measuring large current and high voltage.

Our digital panel meter is connected to CT, PT, DC divider or DC shunt. For example, the AP-168 for AC measurement has its standardized CT connection ranges. It inputs a current of 5A on the CT secondary side to enable scaling of any current value on the primary side.

A5000


TRANSMITTERAPPLICATION EXAMPLES

1. ISOLATIONTRANSMITTER

2. NON-ISOLATIONTRANSMITTER

3. TEMP.TRANSMITTER

4. CURRENTTRANSMITTER

5. CURRENTTRANSMITTER

6. POWERSUPPLY

7. POTENTIOMETERTRANSMITTER

TZ-1X

TZ-5X

TZ-5C

TZ-5D

TZ-5D

TZ-5L

TZ-5B


DCV

&A

Ordering Code

Dimensions

Connection Diagram

DC Voltage Measurement

Accuracy: ±0.1% rdg. ±1 digit (23°C±5°C)

DC Current Measurement

Accuracy: ±0.2% rdg. ±1 digit (23°C±5°C)±0.3% rdg. ±1 digit only for AP-101-25

SpecificationsInput Configuration: Single EndedInput Bias Current: 50PA (Typ.)Conversion Rate: 2.5/secNormal Mode Rejection: TYP.40dB (50/60Hz)Zero Stability: Automatic Zero AdjustmentDisplay: LED. 14.2mm 3 1/2-digitPolarity: A “-” is displayed automaticallyDecimal Point: Settable to any digit positionOverrange Indication: When input exceeds the maximum display,

1999 flashes.Power Supply: AC90~132V

AC180~264VDC5V±5%, 100mA (Max.)DC24V±20%, 30mA (Max.)

Operating Temperature: 0~50°C, 35 to 85% RHPower Consumption: 1.5VADimensions: 48(H) × 96(W) × 73(D)mm DIN SizeWeight: Approx. 150g (For AC), 85g (For DC)Dielectric Strength: AC type; Between input (Lo) terminal and

earth, DC500VBetween power supply terminal and input terminal, earth, common, case, AC1500V/1 min.

DC type; Between input (Lo) and power supply (0V), DC±500V

Insulation Resistance: DC500V 100MΩ at above terminals

DC VOLTMETER & AMMETERAP-101

MaximumResolution

±199.9µA±1.999mA±19.99mA±199.9mA±1.999A

Model RangeInternal

ResistanceInput

Protection

AP-101-21AP-101-22AP-101-23AP-101-24AP-101-25

1kΩ100Ω10Ω1Ω

0.1Ω

±10mA±50mA

±150mA±500mA

±3A

100nA1µA10µA

100µA1mA

AP-101- -

11

1415 ±800V (Option)

Range

~ 21

25

Power Supply 1. AC90~132V2. AC180~264V3. DC5V (Isolated)4. DC24V (Isolated)

~

48

96

73506.6

92

Min.120

Min

.70

＋0.8－0

45＋

0.6

－0

Front

Side

Panel cut

1 2 3 4 5 6 7 8 9 10 11 12 1413 1615 17 18

INPUT DC POWERD.P

0V ＋ 101102103LOHI CO

MH

OLD STA

RT

Features

• Low Cost

• Bright LED 14.2mm (Red)

• AC180~264V, 90~132V, DC5V, DC24V

• 200mV~200V, 200µA~2A Measurement

• ±800V Measurement (option)

Standard 3 1/2 Digit

MaximumResolution

±199.9mV±1.999 V±19.99 V±199.9 V

Model RangeInput

ImpedanceInput

Protection

AP-101-11AP-101-12AP-101-13AP-101-14

100MΩ100MΩ10MΩ10MΩ

±250V±250V±250V±500V

100µV1mV

10mV100mV


DCV

&A

Ordering Code

Dimensions

Connection Diagram


Accuracy: ±0.1% rdg. ±1 digit (23°C±5°C)


Accuracy:±0.2% rdg. ±1 digit(23°C±5°C)±0.3% rdg. ±1 digit only for AP-102-25

SpecificationsInput configuration: Single EndedInput Bias Current: 50PA(Typ.)Conversion Rate: 2.5/sec or 12.5/sec(50Hz), 15/sec(60Hz)Normal Mode Rejection: More than 40dB(50/60Hz)Zero Stability: Automatic Zero AdjustmentDisplay: LED, 14.2mm 3 1/2 -digitPolarity: A”-” is displayed automaticallyDecimal Point: Settable to any digit positionOverrange Indication: When input exceeds the maximum display,

1999 or -1999 flashes.Power Supply: AC90~132V, AC180~264V, DC5V±5%Operating Temperature: 0~50°C, 35 to 85%RHPower Consumption: 1.5VADimensions: 48(H) × 96(W) × 73(D)mm DIN SizeWeight: Approx. 150g(For AC), 85g(For DC)Dielectric Strength: AC type;Between input(Lo)terminal and earth,

DC500VBetween power supply terminal and inputterminal, earth, common, case, AC1500V/ 1 min.DC type;Between input(Lo)and powersupply(0V), DC500V


BCD Data Output (Isolated from input (Lo))Measured data: Tri-state parallel BCD positive logic latch

outputPolarity signal: “1” level at plus input“OVER” signal: “1” level at overflow inputPrinting command signal: A positive pulse of approx 1ms at every

measurement completionEach signal of the above: TTL level Fanout=2*Each signal of the above can be changed to negative logic


MaximumResolution

±199.9µA±1.999mA±19.99mA±199.9mA±1.999A

Model RangeInternal

ResistanceInput

Protection

AP-102-21AP-102-22AP-102-23AP-102-24AP-102-25

1kΩ100Ω10Ω1Ω

0.1Ω

±10mA±50mA

±150mA±500mA

±3A

100nA1µA10µA

100µA1mA

AP-102- -

10

1415

Range

~ 21

25±600V(Option)

~

Power Supply 1. AC90~132V2. AC180~264V3. DC5V (Isolated)

Output

1. None 2. BCD (TTL)3. BCD (Open Collector)5. None 6. BCD (TTL)7. BCD (Open Collector

(2.5/sec)

(12.5/sec)

48

96

73

B.C.D Output

506.6

92

Min.120

Min

.70

＋0.8－0

45＋

0.6

－0

Front

Side

Panel cut

Panel thickness0.8 to 5.0mm

1 2 3 4 5 6 7 8 9 1110 12 13 14A B C D E F H J K L M N P R

1 4 1 4

BCD OUT ENABLE

ENABLE

1 14

2 8 2 8 2 8

D.C

OM

D.C

OM

STA

RT

HO

LD

OV

ER

PC

PO

L

100

100

101

101

102

102 103

103

Features

• BCD(option)

• Bright LED 14.2mm(Red)

• AC180~264V, 90~132V, DC5V


• ±600V Measurement(option)

• BCD Open Collector available

BCD Output(Option)

MaximumResolution

±19.99mV±199.9mV±1.999V±19.99V±199.9V

Model RangeInput

ImpedanceInput

Protection

AP-102-10AP-102-11AP-102-12AP-102-13AP-102-14

100MΩ100MΩ100MΩ10MΩ10MΩ

±250V±250V±250V±250V±500V

10µV100µV1mV

10mV100mV

1 2 3 4 5 6 7 8 9 10 11 12 1413 1615 17 18

INPUT DP

0V＋5V

DC5V

101102103LOHI CO

M

HO

LD

1 2 3 4 5 6 7 8 9 10 11 12 1413 1615 17 18

INPUT AC POWERSUPPLY

DP

101102103LOHI CO

M

HO

LD50

-60Hz

CAN

GE

EA

RTH

(E)

UPPER

DC TYPELOWER

AC TYPELOWER

1 to 5 V4 to 20 mA

Range Measurement Range Display Input Impedance Input Protection Accuracy

1 V2 A

19 1 MΩ10 Ω

±100 V±100 mA

±(0.2% of FS)±(0.2% of FS)

offset ±9999full scale 0 to ±9999

Power supply for sensor : 12 V DC ±10% 50 mA 24 V DC ±10% 25 mA

Process with sensor power supply


DCV

&A

DC VOLTMETER & AMMETERA5-

SpecificationsDisplay: Main display Red LED 14.2 mm height

Sub display Green LED 8 mm heightConversion Rate: 12.5 times/sec.Maximum Display: 9999Overrange Indication: When input exceeds the maximum display,

display OL or –OLZero Display: Leading zero suppressionDecimal Point: Settable to any digit positionExternal Control: Start/Hold, Peak Hold, Digital ZeroOperating Temperature: 0 to 50°C 35 to 85% RHStorage Temperature: –10 to 70°C less than 60% RHPower Supply: AC 100 to 240V±10% (AC main unit)

DC 9 to 60 V (DC main unit)Power Consumption: Approx 4 VA (at 100 V)Dimensions: 96 mm × 48 mm (H) × 147.5 mm (D) DIN sizeWeight: Approx. 450 gDielectric Strength (AC): Power supply/input terminal/output terminal AC2000 V/1 min.

Input terminal/output terminal DC500 V/1 min.Case/power supply/input terminal output terminal AC2000 V/1 min.

Dielectric Strength (DC): Power supply/input terminal/output terminal DC500 V/1 min.Input terminal/output terminal DC500 V/1 min.Case/power supply/input terminal output terminal AC2000 V/1 min.

Insulation Resistance: DC500 V more than 100 MΩ at the above terminals

Features

•Low Cost

•Power Supply AC100~240 V

DC9~60 V

±99.99 mV

Range Measurement Range Display Maximum Resolution Input Impedance Input Protection Accuracy

1101

10 µV 100 MΩ ±100 V ±(0.1% of FS)offset ±9999

full scale 0 to ±9999

±999.9 mV±9.999 V±99.99 V±600 V


12131415

0210 µV1 mV10 mV100 mV

100 MΩ1 MΩ10 MΩ10 MΩ

±100 V±250 V±250 V±600 V

±(0.1% of FS)±(0.1% of FS)±(0.1% of FS)

±(0.15% of FS)


±9.999 mA±99.99 mA±999.9 mA


232425

031 µA10 µA100 µA

10 Ω1 Ω

0.1 Ω

±100 mA±500 mA

±3 A

±(0.2% of FS)±(0.2% of FS)±(0.3% of FS)


Input configuration : Single endedMeasuring method : ∆∑typeNormal mode rejection : More than NMR 50dB (50/60 Hz)

Caution: Range 15 UL approval guarantee up to 300VDC

1 to 5 V4 to 20 mA

Range Measurement Range Display Input Impedance Input Protection Accuracy

1 V2 A

18 1 MΩ10 Ω

±100 V±100 mA

±(0.2% of FS)±(0.2% of FS)


Process

DC Voltage, Current

Ordering CodeA5 -

Input

Output

Display boardMain board

0. None 1. HI & LO setpoint2. Analog output3. RS-232C 4. RS-4855. HI & LO setpoint + analog output6. HI & LO setpoint + analog output + RS-232C7. HI & LO setpoint + analog output + RS-4851. Single 2. Multiple1. AC100 - 240 V (±10%) 2. DC9 - 60 V

01. DC voltage (±99.99 mV) 02. DC voltage (±999.9 mV to ±600 V)03. DC current (±9.999 mA to ±999.9 mA)18. 1-5V, 4-20mA19. 1-5V, 4-20mA with EXC

Dimensions

92

96

487

121

45

147.

5

45+

0.6

-0

92 +0.8- 0

MIN

.70

MIN.120


DCV

&A



Dimensions

Connection Diagram

Front

Side

Panel Cutout

48

96

73506.6

92

Min120

Min

70

＋0.8－0

45＋

0.6

－0

1 2 3 4 5 6 7 8 9 10 11 12 1413 1615 17 18

INPUT

DC POWER

AC POWERD.P

0V ＋

101 102 103104LO EHI

CO

M

CO

M

HO

LDS

TAR

T

Panel thickness 0.8 to 5.0mm

Internally Connected Lo and D. COM

Ordering Code

Features

•Low Cost

•Bright LED 14.2mm(Red)

•AC180~264V, 90~132V, DC5V, DC24V

•2V~200V Measurement

•±700V Measurement(Option)

AP-141- -

12

1415 ±700V (Option)

Range

~

Power Supply 1. AC90~132V2. AC180~264V3. DC5V (Isolated)4. DC24V (Isolated)


SpecificationsInput configuration: Single EndedInput Bias Current: 100PA(Typ.)Conversion Rate: 2.5/secNormal Mode Rejection: More than 50dB(50/60Hz)Zero Stability: Automatic Zero AdjustmentDisplay: LED, 14.2mm 4 1/2 -digitPolarity: A "-" is displayed automaticallyDecimal Point: Settable to any digit positionOverrange Indication: When input exceeds the maximum display,

0000 or -0000 flashesPower Supply: AC90~132V

AC180~264VDC5V±5% 150mA (Max.)DC24V±20% 35mA (Max.)

Operating Temperature: 0~50˚C, 35 to 85%RHPower Consumption: 2VADimensions: 48(H) 96(W) 73(D)mm DIN SizeWeight: Approx. 160g(For AC), 90g(For DC)Dielectric Strength: AC type;Between input(Lo)terminal and earth,

DC500VBetween power supply terminal and inputterminal, earth, common, case, AC1500V/1min.DC type;Between input(Lo) and powersupply(0V), DC500V


±1.9999V±19.999V±199.99V

Model RangeInput

ImpedanceInput

Protection

AP-141-12AP-141-13AP-141-14

100MΩ1MΩ1MΩ

±100V±250V±500V

100µV1mV

10mV

MaximumResolution

Accuracy:±0.03% rdg ±1 digit (23°C±5°C)


DCV

&A

Ordering Code

Dimensions

Connection Diagram


Accuracy:±0.03%rdg ±1digit (23°C±5°C)

SpecificationsInput Configuration: Single EndedInput Bias Current: 100PA (Typ.)Conversion Rate: 2.5/secNormal Mode Rejection: More than 50dB (50/60Hz)Zero Stability: Automatic Zero AdjustmentDisplay: LED 14.2mm 4 1/2-digitPolarity: A "-" is displayed automaticallyDecimal Point: Settable to any digit positionOverrange Indication: When input exceeds the maximum display,

0000 or -0000 flashes.Power Supply: AC90~132V

AC180~264VDC5V ±5%, 170mA (Max.)

Operating Temperature: 0~50°C, 35 to 85%RHPower Consumption: 2VADimensions: 48(H) × 96(W) × 73(D)mm DIN SizeWeight: Approx. 190g (For AC), 125g (For DC)Dielectric Strength: AC type; Between input (Lo) terminal and

earth, DC ±500VBetween power supply terminal and input terminal, earth, common, case, AC1500V/1 min. DC type;Between input (Lo) and power supply (0V), DC ±500V


BCD Data Output (Isolated from input (Lo))･At Open Collector (option)Measured data: Negative logic transistor "ON" at logic "1"Polarity signal: Transistor "ON" at plus input“OVER” signal: Transistor "ON" at overflow inputPrinting command signal: Transistor "ON" during a period of approx.

1ms at every measurement completionTransistor output capacity:Applied voltage, 30V max.

(NPN) current, 10mA max.Saturated output voltage less than1.2V at 10mA

･At TTL levelMeasured data: Tri-state parallel BCD positive logic latch

outputPolarity signal: "1" level at plus input"OVER" signal: "1" level at overflow inputPrinting command signal: A positive pulse of approx 1ms at every

measurement completionEach signal of the above: TTL level Fanout= 2*Each signal of the above can be changed to negative logic

DC VOLTMETER & AMMETER

AP-142- -

11

1415 ±700V (Option)1D Differial input

(11, 12 range)

Range

~

Output 1. None2. BCD (TTL)3. BCD (Open Collector)

Power Supply

1. AC90~132V

2. AC180~264V3. DC5V (Isolated)

48

96

73

B.C.D Output

506.6

92

Min120

Min

70

＋0.8－0

45＋

0.6

－0

Front

Side

Panel cut

1 2 3 4 5 6 7 8 9 1110 12 13 14A B C D E F H J K L M N P R

1 4 1 4

BCD OUT

BCD OUT

ENABLE

ENABLE

1 1 14 4

2 8 2 8 2 8

D.C

OM

D.C

OM

HO

LDS

TAR

T

OV

ER

PC

PO

L

KE

Y

101

100 101 102 103 104

100

100

104

101

102

102 103 1032 8

Features

• BCD (Option)


• AC180~264V, 90~132V, DC5V

• 200mV~200V Measurement

• ±700V Measurement (option)

• Current Measurement (option)

• BCD Open Collector available (option)

BCD Output (Option)

±199.99mV±1.9999V±19.999V±199.99V

Model RangeInput

ImpedanceInput

Protection

AP-142-11AP-142-12AP-142-13AP-142-14


±250V±250V±250V±500V

100µV100µV1mV

10mV

MaximumResolution

AP-142

1 2 3 4 5 6 7 8 9 10 11 12 1413 1615 17 18

INPUT

DC 5V

AC POWERD.P

0V＋5V

101 102 103104LO EAGHI

CO

M

CO

M

HO

LDS

TAR

T

Upper

Lower


DCV

&A

DIGITAL PANEL METERAP-200

SpecificationsInput configuration: Single EndedInput Bias: 50PA(TYP)Conversion Rate: 2.5/secDisplay: LED, 10.16mm (Red)Polarity: A "-" is displayed automaticallyDecimal point: Settable to any digit positionOverrange Indication: Flashes 1999 or -1999Power Supply: DC5V ± 5%Operating Temperature: 0~50; 35 to 85%RHPower Consumption: Approx 60mA (TYP)Dimensions: 48(W)24(H)39.7(D)mm DIN sizeWeight: Approx. 30gDielectric Strength: Between LO and case, DC1500V/min.Insulation Resistance: Between LO and case, DC500V more than 500 Ω

Features

•Low cost

•Screw terminal

•1/32 DIN size, Depth 39.7mm

•200mV ~ 200V measurement

MaximumResolution

± 199.9mV ± 1.999V ± 19.99V ± 199.9V

± 100V ± 100V ± 250V ± 500V

100uV 1mV 10mV 100mV

Range InputProtectionModel

AP-200-11AP-200-12AP-200-13AP-200-14

InputImpedance

100MΩ 100MΩ10MΩ10MΩ

Accuracy: ±(0.1% of rdg 1 digit) (23; ± 5;, 35to85%RH)Stability max 2 digit for only AP-200-11


Ordering CodeAP-200-

Range

Dimensions

Front

Side

24

48

10.16

4.3

57.7

39.7

Panel cutout

Back

45

65mm

35mm

＋0.6－0

22.2＋

0.3－

0


Connection Diagram

1 2 3 4 5

Terminal No. Description1 Input HI2 Input LO3 HOLD4 Power supply 0V5 Power supply +5V


DCV

&A

Ordering Code

Dimensions

Connection Diagram


Accuracy:±0.1% rdg. ±1 digit (23°C5°C) Stability Max. 2 digits for only AP-201A-11

SpecificationsInput configuration: Single Ended.Input Bias Current: 50PA(Typ.)Conversion Rate: 2.5/secNormal Mode Rejection: 40dB(Typ.)(50/60Hz)Zero Stability: Automatic Zero AdjustmentDisplay: LED, 10.2mm 3 1/2 -digitPolarity: A "-" is displayed automaticallyDecimal Point: Settable to any digit positionOverrange Indication: Flashes 1 or -1 of the most significant digit for

an input signal exceeding the maximumdisplay range.

Power Supply: DC5V±5%, 60mAOperating Temperature: 0~50°C, 35 to 85%RHPower Consumption: Approx. 60mADimensions: 24(H) × 48(W) × 73(D)mm DIN SizeWeight: Approx. 40gDielectric Strength: Between input(Lo) terminal and mounted plate.

AC1500V/1 min.Insulation Resistance: DC500V 100MΩ at above terminals

DC VOLTMETER & AMMETERAP-201A

AP-201A-

11

14Range

~

24

48

73

514.8

45

Min.65

Min

.35

＋0.6－0

22.2＋

0.3

－0

Front

Side

Panel cut

1 2 3 4 5 6 7 8 9 10

Operable only wheninput Lo and power supply(0V) are extermally connected

POWERD.PINPUT

101LOHI

CO

M 102 103 0V ＋5V

HO

LD

Features

• Low Cost

• Bright LED 10.2mm(Red)

• DC5V(Non-Isolated)



±199.9mV±1.999V±19.99V±199.9V

Model RangeInput

ImpedanceInput

Protection

AP-201A-11AP-201A-12AP-201A-13AP-201A-14


±100V±100V±250V±500V

100µV1mV

10mV100mV

MaximumResolution


DCV

&A

Ordering Code

Dimensions

Connection Diagram


Accuracy: ±0.1% rdg. ±1 digit (23°C ±5°C)


Accuracy: ±0.2% rdg. ±1 digit (23°C ±5°C)±0.3% rdg. ±1 digit only for AP-202A-25

* These resistors are connected to the outside of the unit.

SpecificationsInput Configuration: Single EndedInput Bias Current: 50PA (Typ.)Conversion Rate: 2.5/sec or 12.5/sec (50Hz), 15/sec (60Hz)Normal Mode Rejection: 40dB (Typ.) (50/60Hz)Zero Stability: Automatic Zero AdjustmentDisplay: LED, 10.2mm 3 1/2-digitPolarity: A "-" is displayed automaticallyDecimal Point: Settable to any digit positionOverrange Indication: When input exceeds the maximum display,

1999 flashes.Power Supply: DC5V ±5%, 120mA

DC12V ±20%, 50mADC24V ±20%, 25mA

Operating Temperature: 0~50°C, 35 to 85%RHPower Consumption: 650 mWDimensions: 24(H) × 48(W) × 73(D)mm DIN SizeWeight: Approx. 50gDielectric Strength: Between Input (Lo) terminal and power supply

(0V), DC ±500VBetween power supply terminal and case,AC1500V/1 min.



±199.9µA±1.999mA±19.99mA±199.9mA±1.999A

Model RangeInput

ResistanceInput

Protection

AP-202A-21AP-202A-22AP-202A-23AP-202A-24AP-202A-25

1kΩ100Ω10Ω*1Ω

*0.1Ω

±10mA±50mA

±150mA±500mA

±3A

100nA1µA10µA

100µA1mA

MaximumResolution

AP-202A- -

Range

Output 1. None2. BCD (2.5/sec)6. BCD (12.5/sec 50Hz)7. BCD (15/sec 60Hz)

Power Supply 3. DC5V (Isolated)4. DC24V (Isolated)5. DC12V (Isolated)

-

BCD Out 1. None2. TTL3. Open Collector

11

14

~ 21

25

~

24

48

73

B.C.D Output (option)

514.8

45

Min.65

Min

.35

＋0.6－0

22.2＋

0.3

－0

Front

Side

Panel cut

2 4 6 81 3 5 7

10 1211 13

14

1 4 1 4

BCD OUT

BCD OUT

EN

AB

LE

1 14

2 8 2 8 2 8

CO

MC

OM

OV

ER

HO

LDPC

PO

L100

100

101

101

102

102

103

91615 19 21 23 25

1817

20 22 24 26

Features

• BCD (option)

• DC5V, DC12V, DC24V (Isolated)


• Conversion Rate 2.5/sec or 12.5/sec (50Hz),

15/sec (60Hz)


ISOLATED Power Supply

±199.9mV±1.999V±19.99V±199.9V

Model RangeInput

ImpedanceInput

Protection

AP-202A-11AP-202A-12AP-202A-13AP-202A-14


±100V±100V±250V±500V

100µV1mV

10mV100mV

MaximumResolution


1 2 3 4 5 6 7 8 9 10

POWERD.PINPUT

101LOHI

CO

M

BLA

NK

ING 102 103 0V ＋

HO

LD

Upper

Lower


DCV

&A


BCD Output(Option)

Dimensions

Connection Diagram

Front

Side

Panel Cutout

24

48

87B.C.D (option)

655

±1

45

Min.65

Min

.35

＋0.6－0

22.2＋

0.3

－0

2 4 6 8

1 3 5 7 9

10 12 14 16 18 20 22 24 26

1311 15 17 2119 23 25

1 4 1 4

BCD OUT

BCD OUT

EN

AB

LE

1 1 14 4

2 8 2 8 2 8

CO

MC

OM

HO

LD

OV

ER

PC

PO

L100 101 102 103 104

100 101 102 103

2 8

1 2 3 4 5 6 7 8 9 10

POWERD.PINPUT

101LOHI 102 103 104 0V ＋

HO

LDS

TAR

TCO

M

Ordering Code

Features

•5V, 24VDC(Isolated)

•Bright LED, 8mm(Red)

•2V to 200V Measurement

•BCD Output(option)

AP-244A- - -

Power Supply 3. 5 to 12VDC 4. 12 to 24VDC

Type of BCD 1. none2. TTL3. Open collector

Output

1. none2. BCD(2.5/sec)6. BCD(12.5/sec)7. BCD(15/sec)

Range 11 1V

14 2A

~


SpecificationsInput Configuration: Single endedInput Bias Current: 100PA(Typ.)Conversion Rate: 2.5/sec, 12.5(50Hz), 15(60Hz)/secNormal Mode Rejection: NMR50dB(50/60Hz)Display: LED 8mm 4 1/2 digitPolarity: A "-" is displayed automaticallyDecimal Point: Settable to any digit positionOverrange Indication: When input exceeds the maximum display,

0000 flashesPower Supply: 5VDC±5%, 24VDC±20%Operating Temp.: 0~50˚C, 35 to 85%RHPower Consumption: 120mA at 5VDC(Max.)

30mA at 24VDC(Max.)Dimensions: 24(H) 48(W) 87(D)mm Din sizeWeight: 50gDielectric Strength: Between input(Lo)terminal and mounted plate,

AC1500V/1 min.Between input(Lo)terminal and powersupply(0V), 500VDC/1 min.

BCD Data Output(Isolated from input(Lo))•At Open collectorMeasured data: Negative logic transistor "ON" at logic "1"Polarity signal: Transistor "ON" at plus input"OVER" signal: Transistor "ON" at overflow inputPrinting command signal: Transistor "ON" during a period of approx. 100

to 200ms at every measurement completionTransistor output capacity: Applied voltage, 30V max

current, 10mA maxSaturated output voltage less than 1.2V at10mA

•AT TTL levelMeasured date: Tri-state parallel BCD positive logic latch

outputPolarity signal: "1" level at plus input"OVER" signal: "1" level at overflow inputPrinting command signal: A positive pulse of approx 100 to 200ms at

every measurement completionEach signal of the above: TTL level Fanout=2* Each signal of the above can be changed to negative logic

±199.99mV±1.9999V±19.999V±199.99V

Model RangeInput

ImpedanceInput

Protection

AP-244A-11AP-244A-12AP-244A-13AP-244A-14


±100V±100V±250V±250V

10µV100µV1mV

10mV

MaximumResolution

Accuracy:±0.03% rdg ±1 digit (23°C±5°C)

Upper

Lower


22

MEMO

23

MEMO

24

MEMO


DCV

&A

Ordering Code

Dimensions

Connection Diagram



SpecificationsInput Configuration: Single EndedInput Bias Current: 50PA (Typ.)Conversion Rate: 2.5/secNormal Mode Rejection: 40dB (Typ.) (50/60Hz)Zero Stability: Automatic Zero AdjustmentDisplay: LED, 14.2mm 3 1/2-digitPolarity: A "-" is displayed automaticallyDecimal Point: Settable to any digit positionOverrange Indication: When input exceeds the maximum display,

1999 flashesPower Supply: DC5V ±5%, 80mA (Max.)Operating Temperature: 0~50°C, 35 to 85%RHPower Consumption: 400mWDimensions: 36(H) × 72(W) × 29(D)mm DIN SizeWeight: Approx. 35gDielectric Strength: Between input (Lo) terminal and case,

AC1500V/1 min.Between input (Lo) terminal and power supply(0V), DC500V



AP-301-

Option

-

Range ~

A. Screw Terminal, 4-20 mA(Range code 11)

B. Screw Terminal, Scaling(Range code 11-14)

C. Screw Terminal, Range Select(Range code 12-14)

D. Screw Terminal, DC-DCIsolated power supply(5V DC)∗BLANK-None

11 1V

14

36

72

2916.34.8

Min.58

＋0.6

－0

＋0.7 －068

Min.96

33Front

Side

Panel cut

1

2

3

4

5

6

7

8

9

HI

LOINPUT

POWER

D.P

BLANKING

HOLD

103

102

101

0V

＋5V

Operate only when input Lo is externally connected to power (0V)

Features

• Compact Size, 36(H) × 72(W) × 29(D)mm

• Bright LED, 14.2mm (Red)



• Isolated DC24V Available (Option A or D)

Compact Size, 14.2mm LED

±199.9mV±1.999V±19.99V±199.9V

Model RangeInput

ImpedanceInput

Protection

AP-301-11AP-301-12AP-301-13AP-301-14


±100V±100V±250V±500V

100µV1mV

10mV100mV

MaximumResolution



DCV

&A

Ordering Code

Dimensions

Connection Diagram



SpecificationsInput Configuration: Differential (11/12-range), Single Ended

(13/14-range)Input Bias Current: 50PA (Typ.)Conversion Rate: 2.5/secNormal Mode Rejection: 40dB (Typ.) (50/60Hz)Zero Stability: Automatic Zero AdjustmentDisplay: LED, 14.2mm 3 1/2-digitPolarity: A "-" is displayed automaticallyDecimal Point: Settable to any digit positionOverrange Indication: Display 1 or -1 of the most significant digit for


Power Supply: DC5V ±5%, 120mAOperating Temperature: 0~50°C, 35 to 85%RHPower Consumption: Approx. 120mADimensions: 48(H) × 96(W) × 34.5(D)mm DIN SizeWeight: Approx. 50gDielectric Strength: Between input (Lo) terminal and mounted

plate. AC1500V/1 min.Insulation Resistance: DC500V 100MΩ at above terminals


AP-501A-

Range11

14

~

48

96

34.5 12.26.3

92

Min.120

Min

.70

＋0.8－0

45＋

0.6

－0

Front

Side

Panel cut

1 2 3 4 5 6 7 8 9 10

POWERD.PINPUT

101LOHI 102103 0V ＋5V

AN

ALO

G・

G

HO

LD

CO

M

When use single ended, connect terminal ② and ③ (COMMON and 0V Terminal is internally connected)

Features

• Low Cost

• Bright LED, 14.2mm (Red)

• Thin Case (Depth 34.5mm)



Super Thin Case, Low Cost

±199.9mV±1.999V±19.99V±199.9V

Model RangeInput

ImpedanceInput

Protection

AP-501A-11AP-501A-12AP-501A-13AP-501A-14


±100V±100V±250V±500V

100µV1mV

10mV100mV

MaximumResolution



DCV

&A


ISOLATED Power Supply

Dimensions

Connection Diagram

Front

Side

Panel Cutout

48

96

3212.26.3

92

Min.120

Min

.70

＋0.8－0

45＋

0.6

－0

1 2 3 5 6 7 8 9 10 11 12 1514134

POWERD.P

ISERIAL DATA OUT

LOHI 101102103 0V ＋5V

COMIN PUT COM PC HOLD

STB SOUT

Ordering Code

Features

•Low Cost

•Bright LED 14.2mm(Red)

•Serial Data Output

•Thin Case(Depth 32mm)

•DC5V(Isolated)

•200mV~200V, 200A~2A Measurement

AP-502-

Range11

14

~ 21

25

1V

2A

~


SpecificationsInput configuration: Single EndedInput Bias Current: 50PA(Typ.)Conversion Rate: 2.5/secNormal Mode Rejection: More than 40dB(50/60Hz)Zero Stability: Automatic Zero AdjustmentDisplay: LED, 14.2mm 3 1/2-digitPolarity: A "-" is displayed automaticallyDecimal Point: Settable to any digit positionOverrange Indication: When input exceeds the maximum display,

1999 flashes.Power Supply: DC5V±5%, 120mA(Max.)Operating Temperature: 0~50˚C, 35 to 85%RHPower Consumption: Approx. 120mADimensions: 48(H) 96(W) 32(D)mm DIN SizeWeight: Approx. 60gDielectric Strength: Between input(Lo)terminal and power

supply(0V), DC500V.Between input(Lo)terminal and mounted plate.AC1500V/1 min.


±199.9mV±1.999V±19.99V±199.9V

Model RangeInput

ImpedanceInput

Protection

AP-502-11AP-502-12AP-502-13AP-502-14


±250V±250V±250V±500V

100µV1mV

10mV100mV

MaximumResolution

Accuracy: ±0.1% rdg. ± 1 digit(23˚C±5˚C)


±199.9µA±1.999mA±19.99mA±199.9mA±1.999A

Model RangeInput

ResistanceInput

Protection

AP-502-21AP-502-22AP-502-23AP-502-24AP-502-25

1KΩ100Ω10Ω1Ω

0.1Ω

±10mA±50mA

±150mA±500mA

±3A

100nA1µA10µA

100µA1mA

MaximumResolution

Accuracy: ±0.2% rdg.±1 digit(23˚C±5˚C) ±0.3% rdg.±1 digit only for AP-502-25



DCV

&A

Ordering Code

Dimensions

Connection Diagram



SpecificationsInput Configuration: Differential (11/12-range)

Single Ended (13/14-range)Input Bias Current: 50PA (Max.)Conversion Rate: 2.5/secNormal Mode Rejection: 40dB (Typ.) 50/60HzZero Stability: Automatic zero adjustmentDisplay: LCD, 12.7mm 3 1/2-digitPolarity: A "-" is displayed automaticallyDecimal Point: Settable to any digit positionOverrange Indication: Display 1 or -1 of the most significant digit for


Power Supply: DC5V ±5%Operating Temperature: 0~50°C, 35 to 85%RHPower Consumption: Approx. 15mWDimensions: 48(H) × 96(W) × 34.5(D)mm DIN SizeWeight: Approx. 60gDielectric Strength: Between input terminal (Lo) and mounting

panel DC500V.Insulation Resistance: DC500V 100MΩ at above terminals


AP-520-

Range11

14

~

48

96

34.5 12.26.3

92

Min.120

Min

.70

＋0.8－0

45＋

0.6

－0

Front

Side

Panel cut

1 2 3 4 5 6 7 8 9 10

POWERDECIMALPOINT

INPUT

101LOHI 102103 0V ＋5V

AN

ALO

G・

G

HO

LD

CO

M

When use single ended, connect terminal ② and ③ (COMMON and 0V Terminal is internally connected)

Features

• LCD, 12.7mm

• Thin Case (Depth 34.5mm)



LCD Display

±199.9mV±1.999V±19.99V±199.9V

Model RangeInput

ImpedanceInput

Protection

AP-520-11AP-520-12AP-520-13AP-520-14


±100V±100V±250V±500V

100µV1mV

10mV100mV

MaximumResolution



DCV

&A

Dimensions

Connection Diagram


Accuracy:±(0.03% of rdg +1 digit ) (23°C±5°C 45~75%RH)

SpecificationsInput configuration: Single endedInput bias current: 100 pA (TYP.)Conversion rate: 2.5/secNormal mode rejection: More than NMR50dB (50/60 Hz)Maximum display: 19999Overrange indication: When input exceeds the maximum display,

0000 flashesDisplay: LED, 14.2 mm (Red)Polarity: A “-” is displayed automaticallyHold: START/HOLD terminal and 0 V shorted or level

"0"Start: START/HOLD terminal and 0 V open or level

"1"Decimal point: Settable to any digit positionOperating temperature: 0~50°C 35~85%RHPower supply: DC 5 V±5%Power consumption: 75 mA (Max.)Dimensions: 48(H) × 96(W) × 34.5(D)mm DIN sizeWeight (unit): Approx. 60 gDielectric strength: Between LO and case, AC 1500 V/l min.Insulation resistance: More than DC 500 V 100 MΩ at the above

terminalsAccessory: Connector, instruction manual

Ordering Code


48

96

34.5

12.26.3

Min

.70

Min.120

92+0.8-0

45+

0.9

-0

Front

Side

Panel cut

1 2 3 4 5 6 7 8 9 10

HI

INPUT DC POWERD.P

L0 NC 104 103 102 101 0V +5V

START/HOLD

Features

• Bright LED, 14.2 mm (Red)

• Thin Case (Depth 34.5 mm)

• Power supply DC 5V (Non-isolated)

• 200 mV～200 V measurement

MaximumResolution

±199.99mV±1.9999V±19.999V±199.99V

Model RangeInput

ImpedanceInput

Protection

AP-540-11AP-540-12AP-540-13AP-540-14


±100V±100V±250V±500V

10µV100µV1mV

10mV

AP-540-

Range

11121314


30

MEMO


DCV

&A

OPEN CASE METERAH-330, 331

EASY Installation

Dimensions

Connection Diagram

Parts

NO.1

4-2.8φ

4-2.8φ

000000000

000000000

14.2

8

000000000

000000000

14.2

8

4.2

3.112.47 12.47 12.47

＊A

＊B

1.6

19

2.54

0.64

17.78

NO.1

NO.8

19

2.54

0.64

17.78

8.54

2.54

PartsOption

Option

4.2

2

2525

＊A

1.6

5.5

8.54

2.54

23 1129.5

2010.5

59POL DP2 DP1

DP2DP3 DP1

65 （mm）

（mm）

12.752.25

＊B2329.5

10.5 14.5

59

65

8

OVF

AH-330

AH-331

1 HIINPUT

POWER

D.P

2

3

4

5

6

7

LO

HOLD

101

102

0V

+5V

1 HIINPUT

POWER

D.P

2

3

4

5

6

7

8

9

LO

101

102

103

0V

COM

HOLD

＋5V

AH-331

OPTION

AH-330

Features

•Uncased, 3 digits(AH-330) 3 1/2 digits(AH-331)

•Bright LED, 14.2mm(Red)

•Hold for AH-331(option)

•Power Supply DC5V±5%


SpecificationsInput Configuration: Single EndedInput Bias Current: 50PA(Typ.)Conversion Rate: 2.5/secNormal Mode Rejection: 40dB(Typ.)Zero Stability: Automatic zero adjustmentDisplay: LED, 14.2mmPolarity: A "-" is displayed automaticallyDecimal Point: Settable to any digit positionOverrange Indication: When input exceeds the maximum display,

lights up "OVER" LED(AH-330)or 1999flashes(AH-331)

Power Supply: DC5V±5%Operating Temperature: 0~50˚C, 35 to 85%RHPower Consumption: AH-330 75mA, AH-331 80mADimensions: 29.5(H) 65(W) 18.2(D)mmWeight: Approx. 20g

±99.9mV±0.999V

±199.9mV±1.999V

Model RangeInput

ImpedanceInput

Protection

AH-330-11AH-330-12AH-331-11AH-331-12


±100V±100V±100V±100V

100µV1mV

100µV1mV

MaximumResolution

Accuracy: ±0.1% rdg.±1 digit(23˚C±5˚C)

Ordering Code

AH-330-331 Range

11

12

~

(AH-331)


DCV

&A

Ordering Code

Dimensions

Connection Diagram


Accuracy: 0.1% rdg.±1 digit(23°C±5°C)

SpecificationsInput Configuration: Single EndedInput Bias Current: 100PA(Typ.)Conversion Rate: 2.5/secNormal Mode Rejection: 40dB(Typ.)Zero Stability: Automatic zero adjustmentDisplay: LCD, 10.2mmPolarity: A "-" is displayed automaticallyDecimal Point: Settable to any digit positionOverrange Indication: When input exceeds the maximum display,

display 1 or -1 of the most significant digitPower Supply: DC5V±5%Operating Temperature: 0~50°C, 35 to 85%RHPower Consumption: 3mA(Max.)Dimensions: 29.5(H) × 65(W) × 16.5(D)mmWeight: Approx. 17g

OPEN CASE METERAH-381

AH-381-

Range 1112

4-2.8φ

25

29.5

50.8

4.2

2.82.8

10.2

122.54

6.1+0.3

1.6

17.78

P-2.54×6

0.64

24.1

8.54

2329.5

59

64.5

mVA

MkΩ

DC

AC

パーツ

1 HIINPUT

POWER

2

3

4

5

6

7

LO

HOLD

COM

0V

＋5V

Features

• LCD, 10.2mm

• Engineering units available

• Power supply 5V DC±5%


LCD Display

±199.9mV±1.999V

Model RangeInput

ImpedanceInput

Protection

AH-381-11AH-381-12

100MΩ100MΩ

±100V±100V

100µV1mV

MaximumResolution


ComparatorSETPOINT COMPARATOR

AM-123

SpecificationsInput Configuration: Single EndedConversion Rate: 12.5/sec(50Hz), 15/sec(60Hz)Normal Mode Rejection: NMR50dB or more(50/60Hz)Display: LED, main display 14.2mm

sub display 8mmPolarity: A "-" is displayed automaticallyOverrange Indication: When input exceeds the maximum display,

display OL or -OLMaximum Display: ±9999Decimal Point: Settable to any digit positionZero Display: Leading zero suppressionExternal Control: Hold, Start, Digital Zero, Peak, Peak-valley, ValleyMemory Backup: EEPROMOperating Temperature: 0~50˚C, 35 to 85%RHPower Supply: AC90~264V(50/60Hz)Power Consumption: 4VA(TYP)(At AC100V)Dimensions: 48(H) 96(W) 98(D)mm DIN sizeWeight: Approx 280gDielectric Strength: Between input/compare output DC500V/1 min

Between power supply and input, case, compareoutputAC2100V/1 min

Insulation Resistance: DC500V 100MΩ or more at above terminalsDielectric Noise: Power supply normal/common mode ±1500VAccessories: Instruction manual, unit label, terminal coverCompare Control System: MicrocomputerSetting Range: -9999~0~+9999Comparative Condition: High setpoint < Indication / HI

High setpoint > Indication > Low setpoint / GOLow setpoint > Indicatyion / LO

Relay Contact Capacity: AC125V 0.5A Resistive loadDC28V 1A Resistive load

Photocoupler Capacity: Voltage MAX. 30VCurrent MAX. 50mASaturation voltage less than 1, 2V at 50mA

Hysteresis: 1 to 999 digit at each setpoints

Features

•Three colour display(red, green, amber)

•Two-setpoint(Hi & Lo)

•Digital Zero, Peak Hold(option)

Display± 99.99mV± 999.9mV± 9.999V± 99.99V

1-5 V

Range Input ProtectionModel

AM-123-11AM-123-12AM-123-13AM-123-14AM-123-1V

Input Impedance100MΩ 100MΩ1MΩ1MΩ1MΩ

± 250VOffset ± 9999

Fullscale ± 9999

Display± 999.9µA± 9.999mA± 99.99mA± 999.9mA

4-20mA

Range Input ProtectionModel

AM-123-22AM-123-23AM-123-24AM-123-25AM-123-2A

Internal Resistance100Ω10Ω1Ω

0.1Ω51Ω

± 50mA± 150mA± 500mA

± 3A± 70mA

Offset ± 9999Fullscale ± 9999

Accuracy: (0.3% of rdg 2 digit) (23˚C5˚C 35 to 85%RH)


Accuracy: (0.1% of rdg 2 digit) (23˚C5˚C 35 to 85%RH)(0.3% of rdg 2 digit) for 25 range

DC Voltage Measurement Ordering CodeAM-123- 1-

Range

Comparator output 1. Relay 2. Photocoupler

Dimensions

Connection Diagram

Front

Side

96

48

899

92

Min

.70

＋0.8－0

45＋

0.6

－0

HI GO LO

(　)：PHOTO COUPLER

① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨

a c b a c b a c b

(c) (e) (c) (e) (c) (e)

① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ HI S/H DZ PH NC

POWERLO COM

Panel thickness 0.8 to 5mm

Upper terminal

Lower terminal

Panel cutout


Com

para

tor

Ordering Code

Dimensions

Connection Diagram


Accuracy : ± (0.03% of rdg +2 digit) (23°C ± 5°C 35 to 85%RH)


Accuracy : ± (0.1% of rdg +2 digit) (23°C ± 5°C 35 to 85%RH)※Accuracy is less than 1 (FSC-OFC) / (FIN-OIN)

Specifications Measuring Section

Input configuration: Single endedConversion rate: 12.5 times/sec(50Hz),15 times/sec(60Hz)Noise rejection ratio: NMR50dB or more (50/60Hz)Display: Red LED, 8mm heightPolarity display: Automatic “-” display when the computation

result is minusOverrange warning: When input exceeds the maximum display,

display OL or -OL Maximum display: ± 9999Decimal point: Settable to any digit positionZero display: Leading zero suppression

Common Section

Memory backup: EEPROM (rewrite 100,000 times)Operating temp.: 0 to 50°C 35 to 85%RHStorage temp.: -10 to 70°C (less than 60%RH)Power supply: DC24V ± 20%Power consumption: 85mA (TYP) at DC24VDimensions: 48mm(W) × 24mm(H) × 388mm(D)Weight: approx.100g (unit only)Dielectric strength: Input terminal (LO) and comparator output,

ANALOG (-), DC500V/min.Power supply (OV) and input (LO), comparatoroutput, ANALOG (-), case, DC500V/min.Input terminal (LO) and case AC1500V/min.

Insulation resistance: DC500V more than 100MΩ at the above terminalsExcitation supply: DC24V ± 10% 25mA ripple less than 200mVp-pAccessories: Instruction manual, rubber paking, terminal

Output Specification Analog Output (isolated input LO)

Can adjust analog output to meet display.※Ripple for resistive load 250Ω, 20mA

SETPOINT COMPARATORAM-213

AM-213 - -

Comparator output 1. Relay2. Photocoupler

Analog output 1. None3. 4 to 20mA

Input code

11. ± 99.99mV12. ± 999.9mV13. ± 9.999V1V. 1 to 5V2A. 4 to 20mA

Features

• NEMA 4 front panel (IP66)

• Excitation power supply DC24V

• Analog output (4 to 20mA) option

• HI and LO setpoints

• 1/32 DIN size

ModelAM-213-11AM-213-12AM-213-13AM-213-1V

Range± 99.99mV± 999.9mV± 9.999V1 to 5 V

Display

OFFSET ± 9999FULLSCALE ± 9999

Input Impedance100MΩ 100MΩ 1MΩ 1MΩ

Input Protection± 250V± 250V± 250V± 250V

Model

AM-213-2A

Range

4 to 20mA

Display OFFSET ± 9999

FULLSCALE ± 9999

Input Impedance

50Ω

Input Protection

± 60mA

Model

AM-213-2A

Range

4 to 20mA

Display OFFSET ± 9999

FULLSCALE ± 9999

Input Impedance

50Ω

Input Protection

± 60mA

HI

E M

48

24

LO

88

22

6.5

11.5

45.0

MIN 65

＋0.6－0

22.2

MIN

35

＋0.

3－

0Front

Side

Panel cut

① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪

INPUT EXC HI COM LO DC POWERANALOG

OUT

HI LO 0V +24V a a 0V +24Vc

c ce

＋

－




AM-215 Featuers

• HI and LO set-point

• Bright LED 8mm (Red)

• 1 to 5V, 4 to 20mA Measurement

• Power Supply DC24V ±20% (Isolated)

• Offset +/–9999 adjustable

• Fullscale +/–9999 adjustable

InputImpedance100M ohm100M ohm1M ohm1M ohm

InputProtection

±100V±100V±250V±250V

Model

AM-215-11AM-215-12AM-215-13AM-215-1V

Range

±99.99mV±999.9mV±9.999V1 to 5V

Display AdjustableOffset±9999Fullscale±9999

Accuracy: ±0.03% rdg. ±2 digit (23˚C±5˚C)

InputImpedance

50 ohm

InputProtection

±60mA

Model

AM-215-2A

Range

4 to 20mA

Display AdjustableOffset±9999Fullscale±9999

Accuracy: ±0.1% rdg. ±2 digit (23˚C±5˚C)

DC Voltage Meaurement


Specifications Measurement sectionInput configuration: Single endedOperation method: Dual slopeInput Bias Current: 50PA (Typ.)Conversion rate: Max. 12.5/sec. (50Hz) or 15/sec. (60Hz)Display: LED, 8mm (Red), 4 digitsPolarity: A “-” is displayed automaticallyOverrange indication: When input exceeds the maximum display,

oL or –oL flashesMaximum display: ±9999 (4 digit)Decimal point: Settable at any position (By pressing sheet

switch)Zero display: Reading “zero” suppression

Comparison sectionControl method: Computation by microcomputerSetting range: –9999 to 9999Conparison condition:

Measured value > High limit set-value – HILow limit set value Measured value High limit set value – GOLow limit set value > Measured value – LO

Setting condition: Low limit set value < High limit set valueHysteresis: 1 to 999 digit for each set pointRelay contact capacity: DC24V resistive road

External control sectionDigital zero: Short DZ terminal and COM terminal or level

“0”.Then digital zero “ON”.

Excition power supply sectionExcition power supply: DC24C ±5%, 25mA

Analog output section (impossible both of Analog output andRS-485 selected)

Output function: DC4 to 20mA or DC0 to 10VOutput specification

RS-485 output section (impossible both of Analog output andRS-485 selected)

Synchronous method: Start and stopCommunication method: 2-wire system half duplex

(Polling and selecting)Transmission speed: 19200bps/9600bps/4800bps/2400

bpsStart bit: 1 bitData length: 7 bitError detection: Even parity (BCC)Stop bit: 2 bitCharacter code: ASCII codeTransmission control: No protocolSignal name used: Non-reversible output (+),

Reversible (–)No. of connectable meters: Up to 31 metersLine of length: Up to 500m in total

Common SpecificationsMemory backup: EEPROM (rewrite 100,000 times)Operating temperature: 0 to 50˚C, 35 to 85%RHStorage temperature: –20 to 70˚C, less than 60%HHPower supply: DC24V ±20%Power consumption: Approx. 4WDimensions: 24(H) 48(W) 87.5(D) DIN sizeWeight: Approx. 100gDielectic strengh: Between power supply (0V), input

terminal and each output terminalDC500V/1 min.Between input terminal and eachoutput terminal DC500V/1 min.Between case, power supply, inputterminal and each output terminalDC500V/1 min.

Insulation resistance: DC500V more than 100M ohm atabove terminals.

Accessories: Instruction manual, settingprocedure

RippleLess than 25mVp-pLess than 50mVp-p

Type4 to 20mA0 to 10V

Risistive load0 to 250 ohmMore than 10K ohm

Accracy±(0.5% of FS)±(0.5% of FS)


Com

para

tor

Connection Diagram

Dimensions

Panel Cut Out

Ordering Code


AM-215- -

Input range

Comparater output

Option output

11. 11 range (±99.99mV) 12. 12 range (±999.9mV) 13. 13 range (±9.999V) 1V. 1V range (1-5V) 2A. 2A range (4-20mA)

1. Relay 2. Photo coupler

1. None 4. RS-485 6. Analog output (4-20mA) 7. Analog putput (0-10V)

1 2 3 4 5 6 7 8 9

POWER !

10 11 12 13 14 15 16 17 18

+24V 0V COM a c a c a c

HI GO LO

EXC(c) (e) (c) (e) (c) (e)

+V0V

POWER

HI LO + - DZ

INPUT TERMINATORANALOGOUT or RS485

3.5 84.3

48.0

24.0

HI LO

E M

45.0+0.6-0

22.2

+0.

3-0

MIN 65

MIN

35


Comparator

Comparison condition:

Comparison relay output: Contact capacity250 V AC 0.2 A Resistive load120 V AC 0.5 A Resistive load28 V DC 1 A Resistive load

Photo coupler output: Voltage = Max. 30 V(NPN) Current = Max. 50 mA

Saturation voltage = less than 1.2 Vat 50 mA

Hysteresis: 1 to 999 digit for each set pointExternal control: Relay reset

Shorted COM terminal and R.REterminal or level "0"Level "0" : 0 to 1.5 VLevel "1" : 3.5 to 5 VInput current : less than -2 mA

Common blockMemory backup: EEPROM (rewrite 100,000 times)

back up 10 yearsOperating temp: 0 to 50°C 35 to 85% RH (No

condensation)Storage temp: -10 to 70°C less than 60% RHPower supply: 90 to 264 V AC (50 Hz/60 Hz)Power consumption: Approx 10 VA typ (at 100 V AC)Dimensions: 96 mm(W) 348 mm(H) 3148 mm(D)

DIN sizeWeight (unit only): Approx 450 gDielectric strength: Input/COM, EXC (0 V), comparative

output, 500 V DC/1 min.Input/COM of each output(BCD:FD.COM, ANALOG:-, RS-232C:SG, RS-485)500 V DC/1 min.Power supply terminal/input terminal,COM, EXC (0 V), case, comparativeoutput, 1500 V AC/1 min.Power supply terminal/COM of eachoutput (BCD:D.COM, ANALOG:-, RS-232C:SG, RS-485) 1500 V AC/1 min.

Insulation resistance: 500 V DC more than 100 MΩ at theabove terminals

Dielectric noise: Power supply terminalnormal/common mode ±1500 V

Power supply for sensor: 24 V DC±10% 40 mA ripple 100 mVp-pAccessories: Instruction manual

quick manual, setting list, unit label,terminal cover

High high limit set value Measured valueHigh limit set value Measured valueHigh high limit set value Low low limit set value

Measured value High limit set value Low limit set valueMeasured value Low limit set valueMeasured value Low low limit set value

HHHI

GO

LOLL

Comparison condition Comparisonresult


Accuracy: ±(0.03% of rdg + 2 digit)(23°C±5°C 45 to 75% RH)


Accuracy: ±(0.1% of rdg +2 digit)(23°C±5°C 45 to 75% RH)±(0.3% rdg +2 digit) for 25 range

General specifications Measurement blockInput configuration: Single endedOperation method: Dual slopeConversion rate: 12.5 time/sec (50 Hz), 15 time/sec (60 Hz)Noise rejection ratio: NMR more than 50 dB (50/60 Hz)Temp. coefficient: ±(0.005% of rdg +0.3 digit)/°CDisplay: Red LED, 14.2 mm height

Green LED, 8 mm height for setpointPolarity display: Automatic "–" display when the computation

result is minusOverrange warning: When input exceeds the maximum display,

display 0L or –0LMaximum display: 0 to ±9999 (4 digit)Decimal poin: Settable to any digit position (by front sheet

switch)Zero display: Leading zero suppression

External control blockHold: Shorted COM terminal and S/H terminal or level "0"Start: Shorted COM terminal and S/H terminal or level "1"Digital zero: Shorted COM terminal and DZ terminal or level "0"

(displayed zero and that value is stored)Peak holdValley hold: Shorted COM terminal and PH terminal or level "0"Peak Valley holdPattern selection: Any one of 8 patterns is settable in combination of

COM terminal and P.SEL terminal 0, 1 and 2Level "0" : 0 to 1.5VLevel "1" : 3.5 to 5 VInput current : less than -2 mA

Comparison blockControl method: Computation by microcomputerSetting range: -9999 to 0 to +9999 (Including polarity)Setting condition:

±9.999mA±99.99mA±999.9mA4 to 20mA

RangeInput InternalResistance

InputProtection

2324252A

DA

10Ω1Ω

0.1Ω10Ω

±150mA±500mA

±3A±150mA

Offset±9999Fullscale±0~9999

MeasuringRange

DisplayAdjustable

±99.9mV±999.9V±9.999V±99.99V±700.0V1 to 5V

RangeInput InputImpedance

InputProtection

1112131415IV

DV

100MΩ100MΩ1MΩ

10MΩ10MΩ1MΩ

±250V±250V±250V±500V±700V±250V

Offset±9999Fullscale±0 to 9999

MeasuringRange

DisplayAdjustable


Features• Conversion rate 12.5times/sec(50Hz) or

15times/sec(60Hz)

• Four setpoint(Can display two setpoint)

• Maltiple range

• Scaling value and setting value stored 8 pattern

• Peak hold, Valley hold, Peak-valley hold, Digital zero,

Moving average(standard)

• Power supply for sensor 24VDC 40mA

• Direct setting function

• Power supply 90 to 264VAC

RS232C output


Com

para

tor

Output specifications BCD data output (isolated input (Lo))• At TTLMeasured data: Tri-stage parallel BCD, Positive logic, latch outputPolarity signal: Level "1" at minus inputOver signal: Level "1" at overflow inputPrinting command signal: Positive pulse approx. 20 ms at every

measurement completion (available negativelogic the above signals)

TTL level, funout 2, CMOS 5V

• At open collector (NPN)Measured data: Negative logic transistor "ON" at logic 1Polarity signal: Transistor "ON" at minus inputOver signal: Transistor "ON" at overflow inputPrinting command signal: Transistor "ON" during a period of approx. 20

ms at every measurement completionTransistor output capacity: Applied voltage, max. 30V current max. 10

mA saturated output voltage less than 1.2 Vat 10 mA

ENABLE: Shorted ENABLE terminal and D.COMterminal or level "0", Transistor output areOFF (TTL output is high impedance status)Level "0" : 0 to 1.5 VLevel "1" : 3.5 to 5 VInput current : less than - 2 mA

RS-485 (Isolated input (Lo))Electrical characteristics: Conforming to EIA RS-485Communication method: 2-wires system half-duplex (Polling and selecting)Transmission speed: 2400/4800/9600/19200 bpsStart bit: 1 bitData length: 7 bitsError detection: Even parity (BCC)Stop bit: 2 bitsCharacter code: ASCII codeTransmission control: No protocolSignal name used:

No. of connectable meter: Up to 31 metersLine length: Up to 500 m in total

RS-232C (Isolated input (Lo))Electrical characteristics: Conforming to EIA RS-232CCommunication method: Full duplexSynchronous method: Start and stopTransmission speed: 2400/4600/9600/19200 bpsStart bit: 1 bitData length: 7 bitsError detection: Even parityStop bit: 2 bitsCharacter code: ASCII code

Analog output (Isolated input (Lo))Resolution: 13 bitsOutput response: Less than 0.5S (0 to 90%)

* Ripple for 4 to 20 mA at resistive load 250Ω, 20 mA

Output Resistive load RippleAccuracy (23°C ± 5°C)0 to 10 V4 to 20 mA

50 mV P-PLess than 0.5%

More than 10 kΩ0 to 550Ω

±0.5% FS±0.5% FS

Signal name Signal Signal directionNon-reversible outputReversible output

Input/outputInput/output

+–


Ordering Code

Dimensions

Connection Diagram

(A.OUT)0-10V4-20mA

Relay Output

RS-485

HH

OFF ON

TERMINATER

C

+ – (C) (C) (C) (C) (C)(e) (e) (e)

C LLHI GO LO

1 2 3 4 5 6 7 8 9 10

P.SEL

0

HI CLO ECOM

BA

1 2 P.H D.Z R.RE S/H 0V +24V

EXC

AC POWER

1

9

2 3 4 5 6 7 8

10 11 12 13 14 15 16 17

BCD OUT

2

1 4 1 4 1 4 1 4

1

2

8 2 8 2 8 2 8

34

33

NC NC

NCNC

PC

POL

NCNC NCOVER D.COM

D.COM

NCNC NC D.COM

D.COM

ENABLE101100 102 103

101100 102 103

13

SG

CT

SR

TS

RX

DT

XD

251

14

Upper

RS232C output

BCD output

Lower

Photo Coupler

HH HI HH

LO LLSET

ME

P.NO DZ RE

PH HH.LL

HI SETGO LO

S

96

48

ME

LL

92

Min120

Min

70

+0.8–0

45+

0.6

–0

148

144

7

127

MADE IN JAPAN

33


Front

Side

Panel Cutout

AM-147-

Comparator Output

- -

Output

1. None2. BCD(Open collector)3. BCD(TTL)4. RS-4855. RS-232C6. ANALOG(4 to 20mA)7. ANALOG(0 to 10V)

InputRange

Power Supply 1. 90 to 264VAC

1. Relay2. Photo Coupler

DV(11,12,13,14,15,1V)

DA(23,24,25,2A)

39

Comparator



Comparison relay: 250 AC 0.2A Resistive load120V AC 0.5A Resistive load28V DC 1A Resistive load

Photo-coupler output: Sink current, 20mA max. (Less than30V)Output saturation voltage, Less than1.2V at 20mA

Hysteresis: Settable from 1 to 9999 digits foreach comparison set value

External Control: ResetContact capacity Comparison operation is suspended

when COM andr1R.RES terminals areshorted or input level is set at “0”.“0” level : Less than 1.5V“1” level : 3 to 30VInput current : Less than -5mA

Common specificationsMemory backup: Set data is stored for approx. 10

years by using EEPROM.Operating temperatureand humidity ranges: 0 to 50˚C

35 to 85% RHPower supply: 90 to 264V AC (50Hz / 60Hz)Power consumption: Appox. 5VA (st 100 AC)Dimensions: 48mm (H) x96mm (W) x161mm (D),

DIN sizeWeight: Approx. 600gDielectric Strength: 500V DC between input / earth E

and case 500V DC between inputterminal / common, digital common,sensor power supply and relayoutput 1500V AC between powersupply terminal / common, digitalcommon, sensor power supply,case and relay output.

Insulation resistance: More than 100MΩ at 500V DCbetween each terminal describedabove

Noise rejection: Power terminals, normal / commonmode, ±1500V square waveform for1ns at rise, noise, width, 500ns (BYnoise simulator)

Sensor power supply: 12V± 10% 80mARipple, Less than 200mVp-p

Accessory: Instruction manual

High high limit set-value Measured valueHigh limit set-value Measured valueHigh / high limit set-value Low / low limit set-value

Measured value High limit set-value Low limit set-valueMeasured value Low / lowlimit set-valueMeasured value Low limit set-value

HHHI

GO

LOLL

Comparison condition Comparison resultAM-749 DC Voltage Measurement

Accuracy: ± 0.03% rdg ±2 digit (23°C±5°C)


Accuracy: ± 0.1% rdg ±2 digit (23°C±5°C)± 0.3% rdg ±2 digit only for 25 range

General specifications• Measurement blockMeasurement function: Specify one measuring range from DC voltage

and DC current measuring ranges.Input circuit: Single-endedOperation method: Dual slopeInput bias current: 100pA (TYP)Conversion rate: 12.5 times / sec (at 60Hz)

15 times / sec (at 50 / 60Hz)Noise rejection ratio: NMR-More than 50 dB (at 50 / 60Hz)Display: 7-segment LED (Light emitting diode numeric

element)Height, 10mm (red)Monitor / sub-display units-Height 8mm (green)

Polarity display: "-" is displayed when the computed result isnegative.

Overrange warning: "OL" LED (red) flashes when input signal exeedsmeasuring or display range.

Mximum display: ±99999 (5 digits)Decimal point: Settable at any position

(BY pressing sheets switch)Zero display: Reading "zero" suppression• External controlHold: Shorting between COM and S/H terminals or "0" levelStart: Open between COM and S/H terminals or "1" level

Value just before COM and DZ terminals are shortedDigital zero: or input level is set at "0" is displayed as "zero" and

that value is stored.Peak hold: Respective function is activated when COM andValley hold PH terminals are shorted or input level is set at "0".Peak valley hold:Pattern selection: Any one of 8 patterns is settable in combination of

COM terminal with any one of P SEL terminals 0, 1,and 2."0" level : less than 1.5V"1" level : 3V to 30VInput current :less than -5mA

• Comparioson blockControl method: Computaion by microcomputerMeasurinng range: High / Low limit setting including polarity, –99999 toComparison: 0 to +99999Setting condiotion: By sampling period

No setting restrictions for set-valueComparison condition:

±19.999mA±199.99mA±1.9999A4~20mA


Max allowableinput voltage

2324252A

DA

10Ω1Ω

0.1Ω10Ω

±150mA±500mA

±3A±150mA


MeasuringRange

DisplayAdjustable

±199.99mV±1.9999V±19.999V±199.99V±700.0V

1~5V


Max allowableinput voltage

1112131415IV

DV

100MΩ100MΩ1MΩ

10MΩ10MΩ1MΩ

±250V±250V±250V±500V±700V±250V


MeasuringRange

DisplayAdjustable

Features• Conversion Rate 12.5 times / sec (50Hz),

15 times / sec (60Hz).

• Peak, Valley, Peak-Valley Hold, Digital zero.

• Eight Pattern Setting (EEPROGRAM Back Up).

• Including Power Supply For Sensor 12V 80mA.

• Power Supply (AC90~264V).

• Direct Setting Function.

Four Setpoints


Com

para

tor

10 11 12 13 14 15 16 17

1 2 3 4 5 6 7 8

9

０１２ PH DZ R.RES S/H 0 12V

AB

CHI LO COM E AC POWER

P.SEL EXC

2 8 2 8 2 8 2 8

1 4 1 4 1 4 1 4

NC NC

NC NC

NC

NC

DG

DGPC

OVER

POL

ENABLEBCD output DG

DG

34

33

2

1

100 101 102 103

100 101 102 103

2 8

1 4

104

104

25 1413 1

SG RTS TXDCTS RXD

RS-232C

D-SUB Connector

① ② ③ ④ ⑤ 　 ① ② ③ ④ ⑤

RS485 ANALOG output

NCNC SG＋－＋－＋－ NC

1V～5V 4mA～20mA

TERMINATER

OFF ON

1 2 3 4 5 6 7 8 9 10

HH HI GO LO LLca acacacac

cecececece

(Relay outpuy)

(Photo coupler output)


Dimensions

Connection Diagram

Connection Diagram

Front

Side

Panel Cutout

Upper

Lower

CONT

TZ PH DZ RE OL

HH HI GO LO LL

P R M S

96

48

153

1317

161

170

44.5

92

Min.120

Min

.70

＋0.8－0

45＋

0.6

－0

Ordering Code

AM-749

Data Output

- - -Comparator Output 1. Relay

2. Photo

1. None2. BCD (Open collector)3. RS-4854. RS-232C5. ANALOG

Power Supply 1.AC90V~264V

Range DV (11,12,13,14,15,1V)DA (23,24,25,2A)

Optional specifications•BCD output [Isolated from input(LO)]Measured date: Negative logic

NPN open-collector outputPolarity signal: Transistor "ON" at minus inputOVER signal: Transistor "ON" at "OVER" inputPrinting command signal: Transistor "ON" for approx. 10ms at the end of

measurementENABLE: All date output transistors are turned "OFF"

when ENABLE and digital common terminalsare shorted or input level is set at "0"."0" level:Less than 1.5V"1" level":3 to 30VInput current:Less than -5mA

Transistor output capacity: Applied voltage, 30V max. Current, 10mA max.Output saturation voltage:Less than 1.2V at10mA*TTL output is also available.

•RS-232C [Isolated from input(LO)]Electrical characteristics: Conforming to EIA RS-232CCommunication method: Full duplexSynchronous method: Start and stopTransmission speed: 2400/4800/9600/19200 bpsStart bit: 1 bitData length: 7 bitsError detection: Even parityStop bit: 2 bitsCharacter code: ASC IITransmission control: No protocol•RS-485 [Isolated from input(LO)]Electrical characteristics: Conforming to EIA RS-485Synchronous method: Start and stopCommunication method: 2-wire system half-duplex

(Polling and selecting)Transmission speed: 2400/4800/9600/19200 bpsStart bit: 1 bitDate length: 7 bitsError detection: Even parity

BCC(Block check character)check sumStop bit: 2 bitsCharacter code: ASC IITransmission control: No protocolSignal name used:

No. of connectable meters: Up to 31 metersLine length: Up to 500m in total

•Analog output [Isolated from input(LO)]Any display range to output analog signal can be set.Resolution: 16 bitsOutput response: Less 0.5s

Moving average: Digital filter functionFixed zero: 100 -digit is fixed to "0" for displayDisplay blanking: Blanking of LEDs on main, monitor/sub-display

units.Tracking zero: (Only for RS-232C and RS-485 meters)

Zero-point shift is digitally, automaticallycorrected. Activated when digital zero functionbecomes valid.

Panel thickness 0.8 to 5.0mmSignal name Signal Signal direction

Non-reversible outputReversible output

+–

Input/outputInput/output

Output Resistive load Accuracy (23˚C ±5˚C)

1 to 5V4 to 20mA

More than 10kΩ0 to 600Ω

±0.5% F.S±0.5% F.S

Ripple

50mVp-p–



AMH-752

4000 Time/sec Features

•Conversion Rate 1000/sec~4000/sec

•2 input computation(A, B)

•4-sets/4-pattern Setting

•Peak, Valley, Peak-Valley hold(Option)

•Digital zero(Option)

•RS-232C Communication(Option)

•BCD, ANALOG Output(Option)

•Bright LED 10mm(Red)


Specifications1.Measuring function: Specify one type from among DC voltage, DC

current and instrumentation input signalmeasurements.

2.Operation method: Successive approximation type3.No. of input points: 2(A ch. and B ch.)ch./channel*4.Input selection: A, B, A+B, A-B, A & B, and (A-B)/ |B| 1005.Input circuit: Single-ended type6.Input bias current: 1nA(TYP)*7.Conversion Rate: 1.25 times/sec to 4000 times/sec(For 1 ch.)

0.652 times/sec to 2000 times/sec(For 2 ch.)8.Display: LED

Measured-value display unit characterheight;10.0mm(red)Monitor character height ; 8mm(green)

9.Display speed: 12.5 times/sec(Only in the normal speed mode)Display in the high-speed mode ; Displayed onlyduring hold.

±199.9mV±1.999V±19.99V±199.9V

Model RangeInput

ImpedanceInput

Protection

AMH-752-11AMH-752-12AMH-752-13AMH-752-14

100MΩ

10MΩ

±250V

±500V

OFFSET±1999

FULLSCALE±1999

DisplayAdjustable

Accuracy: ±0.1% ±2 digit(23°C±5°C)(a1)(Normal Speed Mode)±0.1% ±4 digit(23°C±5°C)(a1)(High Speed Mode)


±199.9µA±1.999mA±19.99mA±199.9mA±1.999A

Model RangeInternal

ResistanceInput

Protection

AMH-752-21AMH-752-22AMH-752-23AMH-752-24AMH-752-25

OFFSET±1999

FULLSCALE±1999

1kΩ100Ω10Ω1Ω

0.1Ω

±10mA±50mA

±150mA±500mA

±3A

DisplayAdjustable

Accuracy: ±0.2% rdg. ±2 digit(23°C±5°C)(a1)±0.3% rdg. ±2 digit only for AMH-75X-25±0.2% rdg. ±4 digit(23°C±5°C)(a1) ±0.3% rdg. ±4 digit only for AMH-75X-25

Normal Speed Mode

High Speed Mode

1-5V Measuement

OFFSET ±1999

FULLSCALE ±1999

Model RangeInput

ImpedanceInput

Protection

AMH-752-1V 1-5V 1MΩ ±250V

DisplayAdjustable

Accuracy: ±0.1% rdg. ±3digit (23°C±5°C) (a1) (Normal Speed Mode)±0.1% rdg. ±5digit (23°C±5°C) (a1) (High Speed Mode)

4-20mA Measurement

OFFSET ±1999

FULLSCALE ±1999

Model RangeInput

ResistanceInput

Protection

AMH-752-2A 4-20mA 10Ω ±150mA

DisplayAdjustable

Accuracy: ±0.1% ±3 digit (23°C±5°C) (a1) (Normal Speed Mode)±0.1% ±5 digit (23°C±5°C) (a1) (High Speed Mode)

*a=Scaling Coefficient

Mode High Speed Mode

Conversion Rate(1ch) per sec.Conversion Rate(2ch) per sec.

4000(1)

2000

1 2 3 4No.2000(2)

1000

1333.3(3)

666.7

1000(4)

500

Mode Normal Speed Mode


1000(5)

500

5No.500(10)

250

6250(20)

125

7125(40)

62.5

8100(50)

50

950

(100)

25

10

Mode Normal Speed Mode


25(200)

12.5

11No.12.5(400)

6.25

1210

(500)

5

135

(1000)

2.5

142.5

(2000)

1.25

151.25

(4000)

0.625

16

( )Average time

10.Polarity display: Automatic "_" display when thecomputation result is minus

11.Overrange warning: Overflow display when input signalexceeds measuring rangeLED(red)flashes.(Display:Value justbefore overflow occurs)

12.Zero display: Leading "zero" suppression13.Decimal point: Settabel to any position(by dip switch at

the front).14.Maximum display: ±199915.External control: Start/hold(start hold A type)

Start/Start terminal open(or 5 V)Hold/Shorting between digital common

and hold terminals(or 0 V)*:Sample hold(start hold B type)Only one measurement is performed fromrise of positive or negative pulse of morethan 500µ s and the result is out-put.*:Digital zeroFunction of making the mechanical initialvalue such as of pressure sensor,potentiometer, etc. to zero electrically. By shorting betweenthe digital common and digital zero(for A ch. or B ch.) terminals, or at 0V;The displayed valuejust after the above shorting made orvoltage is set to 0 V is changed to "zero"and the value at that time is stored. (A ch. and B ch. can be independentlycontrolled.)*:Peak hold, valley hold and peak valleyhold•Peak hold Display of maximum valuemeasured•Valley hold;Display of minimum valuemeasured•Peak valley hold;Display of the difference betweenmaximum and minimum value measuredThe respective display function workswith the common and above terminalsshorted or at 0 V. (However, only display is made, andcomparison output is always inaccordance with voltage or current valueapplied between input Hi and Lo.)*:Settable on the sheet key at the front.


Com

para

tor

SETPOINT COMPARATOR

Ordering Code

Optional Specifications1.BCD output: Tri-state, Parallel BCD output, Fan out 2(TTL level) Polarity output/At minus value;"1"

Overflow output/At overflow;"1"P.C output;At the end of A/D conversion,plus pulse in approx. 500µs width*Only in the normal speed mode

2.RS-232C: Bidirectional(Full duplex)(Conformance)3.Analog output: Output voltage;±0 to 2.5V

Resolution;0.25mV/digitAccuracy;0.5% FS(23˚C±5˚C)External resistance;More than 20kΩOvervoltage;Approx.±3.5V, less than 5V*Any of high speed and normal speedmodes is available.

4.Absolute value display comparison:Function of outputting absolute valueregardless input single polarity

AMH-752

Output

- - -ComparesOutput

1. Relay Output (0.625Hz~80Hz)2. Photo Coupler Output (0.625Hz~4kHz)

1. None2. BCD3. ANALOG4. BCD,ANALOGR. RS-232C

PowerSupply

1. AC90~132V2. AC180~264V11

14Range21

25

1V

2A

~ ~

Comparison Section

Common Specifications1.Memory backup: Set data can be reserved for about 10 years

using EEPROM.2.Operating temperature and humidity:

0 to 50˚C, 35 to 85% RH3.Power supply: 90 to 132V AC 50/l60Hz

180 to 264V AC 50/60Hz(Internal jumper wire selection)

4.Power consumption: Approx. 5VA(at 100V)5.Dimensins: 48mm(H) 96mm(W) 158mm(D), DIN size6.Dielectric strength: Between input and grounding(E)terminals,

500V DCBetween input and digital common/relayoutput/transistors output;500V DC,eachBetween power supply terminal and inputterminal/grounding(E)/digital common/relayoutput/transistor outpu;1 min at 1500V AC,each.

7.Insulation resistance: Between each terminal described above, morethan 100MΩ at 500V DC

8.Weight: Approx. 600g(mainframe)9.Accessories: Input/output screw terminals, 2 pcs.

Instruction manualData output plug(Amphenol 57-30360)

10.Others: For unit display, contact us.

1.Control method: Computation by microcomputer2.Setting range: High/low limit setting including polarity(2/4-

step setting)-1999 to 0 to +1999

3.Comparison conditions (display):

4.Comparison display: As a comparison result, the respective lightemitting diode lights.

5.Comparison relay output:HH, HI, GO, LO, and LL(1 "a", each)

6.Relay output cycle: Approx. 12.5msConversion Rate: When the speed is slower

than 80 times /sec, output foreach sampling.

Conversion Rate: When the speed is fasterthan 80 times/sec, outputsthe result at that time atabout 12.5 msecintervals.(Excluded atstart/hold.)

7.Relay contact capacity: 250V AC, 0.1A Resistive load120V AC, 0.5A Resistive load28V DC, 1A Resistive load

8.Photo-Coupler output: Sink current;20mA max.(less than 30 V)(NPN open-collector)

9.Photo-Coupler output cycle:Approx. 250µs at the sampling speed of 4000times/sec for 1ch. inputFor others;Depending on each samplingspeed

10.Hysteresis: Settable from 1 to 999 digits for eachcomparison set-value.

11.External control: Comparison output reset with the reset anddigital common terminals shotred(or at 0 V)

At 1ch. input

AMH-752HH (HI)

HI

GO

LO

(LO) LL

Comparison resultComparison condition

Measured value>High/high limit set-valueHigh/high limit set-value≧Measured-value

>High limit set-valueHigh limit set-value≧Measured-value

≧Low limit set-valueLow limit set-value<Measured-value

≧Low/low limit set-valueLow/low limit set-value>Measured-value

AMH-752



AMH-752 Data Output

1 2 3 4 5 6 7 8

1 2 4 8 1 2 4 8

1 2 4 8 81 2 4

9 10 11 12 13 14 15 16 17 18

19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36

101 103

100 102

BCD OUTPUT ANALOG

BCD OUTPUT

Control Control

POLOVER

PC RTS CTS

RXDP.H TXD

SG

SG 0

D.COM

D.COM

P.SEL

P.SEL

RS-232C

RS-232C

1

ENABLED.Z.(B)D.Z.(A)

D. COM

A.OUT

A.OUT COM

25 1413 1

SG RTS TXDCTS RXD

D-SUB Connector

Dimensions

Connection Diagram

1587

※

92

Min.120

Min

.70

＋0.8－0

45＋

0.6

－0

HH

Relay Output

Relay Coupler Output

(UPPER) 　c=Common 　a= a Contact

(UPPER) 　e= Emitter 　c= Collector

HI GO LO LL

① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩

ac c a c a c a c a

HH HI GO LO LL

ce e c e c e c e c

① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩

INPUT

(LOWER)

Control E POWER

① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩

A.GAch Bch A.G COM S/H RESET

５min 3.6max

φ3.2min

5.9max

Upper

Lower

Front

Side

Panel Cutout


TZ PH DZ RE

HH HI GO LO LL

OVEHS

SPM

96

48


Com

para

tor

SETPOINT COMPARATORAMH-762

High Conversion rate1000times/sec (Normal speed mode)4000times/sec (High speed mode)

Features

• High Conversion Rate, 1000times/sec (Normal speed mode)

4000times/sec (High speed mode)

• 2 inputs computation (A input, B input)

• Digital Zero, Peak Hold, Valley Hold, Peak-Valley Hold

• Available 8-pattern Setting for Scaling value and setpoints

(Data Back-up EEPROM)

•Excitation Supply 24VDC 40mA

•RS-232C, RS-485 Output (Option)

•BCD, Analog Output (Option)

•Power Supply (90 to 264VAC)

•Bright LED, 10mm (Red) DC Voltage Measurement

Specifications• Measuring SectionInput Configuration: Single EndedOperation Method: Successive approximation typeNo. of Input: A input and B inputConversion Rate : 0.5times to 4000times(only use one input)

0.25times to 2000times(use two input)

Range Display Adjustment Input Impedance Input ProtectioModel

AMH-762-13 ±9.999V 1MΩ ±250V

Accuracy:±0.1% FS (23°C±5°C)

Offset ±10000Fullscale ±0 to 10000

1 to 5V Measurement

Range Display Adjustment Input ImpedanceModel

AMH-762-1V 1 to 5V 1MΩ



Input Protectio

±250V

4 to 20mA Measurement

Range Display Adjustment Internal ResistanceModel


AMH-762-2A 4 to 20mA 50Ω

Input Protectio

±70mA


※Condition for accuracy, (FSC-OFS)/(FIN-OIN) is less than 1

Display: LED,10mm hight (Red)8mm hight (Green) for monitor

Display Speed: 1.25, 2.5, 12.5, 25times/sec forNormal speed modeWhen pressed key of "C", appeardisplay value for High speed mode

Polarity : A "-" is displayed automaticallyOverrange Indication: When input exceeds the maximum

display, display OL and flashMax. Display: ±99999Decimal Point: Settable to any digit positionZero Display: Leading zero suppressionEXternal Control: Hold ; Shorted D.COM and S/HA,

S/HBterminal or level "0" Start; Open D.COM and S/HA, S/HBterminal or "1" levelDigital Zero; Shorted D.COM andDZA, DZB terminal or level "0"Peak Hold; Valley Hold; Shorted D.COM and PHterminal or level "0"Peak Valley Hold;(Compare the

display value)Selected either one

Pattern Select; Combination ofD.COM and P.SEL terminal

Level "0"= 0 to +1.5VLevel "1"= +3.5 to 5VCurrent= less than -5mA Not provided PH, DZA and DZB forRS-232C and RS-485 output

High Speed Mode

Conversion Rate(1ch) per sec.

Conversion Rate(2ch) per sec. 2000

4000

1

1000

2000

2ModeNo.

Nomal Speed Mode


Conversion Rate(2ch) per sec. 500

1000

4

500

250

8

400

200

10

200

100

20

100

50

40

50

25

80

40

20

100ModeNo.

Mode Nomal Speed Mode



No.

10

20

200

10

5

400

5

2.5

800

4

2

1000

2

1

2000

0.5

0.25

8000

1

0.5

4000



AMH-762• Comparator SectionControl System: MicrocomputerSetting Range: -99999 to +99999 with polarity Comparative Condition: High High setpoint < Indication /HH

High setpoint < Indication /HIHigh setpointIndicationLow setpointHigh high setpointIndicationLow low /GO

setpointLow setpoint > Indication /LOLow low setpoint > Indication /LL

Relay Contact Capacity: 250VAC 0.2A Resistive load120VAC 0.5A Resistive load28VDC 1A Resistive load

Photo Coupler Outpu: Voltage=Max. 30VCurrent=Max. 20mASaturation voltage=less than 1.2V at 20mA

Hysteresis: 1 to 9999 digit each setpointsExternal Control: Reset; Shorted D.COM and R.RE terminal or

level "0"

• Common SectionMemory Back-up : EEPROM (Rewrite more than 100,000 times)

back up 10 yearsOperating Temp: 0 to 50°C 35 to 85% RH Power Supply: 90 to 264VACPower Consumption: Approx 10VA TYP. (at 100V)Dimensions: 48(H) 96(W) 161(D) mm DIN sizeWeight: Approx. 600g (unit only)Dielectric Strength: Input/earth, COM, Comparative output,

DC500V/ 1 min.Input/D.COM of each output terminal,DC500V/1 min.Power supply/D.COM, case, comparativeoutput, 1500VAC/1 min.

Insulation Resistance: 500VDC more than 100M ohms at the aboveterminals

Excitation Supply: 24VDC ±10% 40mA (Ripple less than 100mVp-p)

Accessories: Instruction manual

Output BCD data output (Isolated input (Lo))

•At Open collector (NPN)Measured Data: Negative logic transistor "ON" at logic 1Polarity Signal: Transistor "ON" at minus inputOver Signal: Transistor "ON" at overflow input Printing Command Signal:

Transistor "ON" during a period at everymeasurement completion

Transistor Output Capacity:Applied voltage, 30V max. current 10mA max.Saturated output voltage less than 1.2V at10mA*Available TTL output

RS-485 (Isolated input (Lo))Electrical Characterstics: Conforming to EIA RS-485Synchronous Method: Start and stopCommunication Method: 2-wires system half-duplex (Polling and

selecting)Transmission Speed: 2400/4800/9600/19200 bPSStart Bit: 1 bitData Length: 7 bitsError Detection: Even parity (BCC)Stop Bit: 2 bitsCharacter Code: ASCII codeTransmission Control: No protocolSignal name used:

No. of Connectable Meter: Up to 31 metersLine Length: Up to 500m in total

RS-232C (Isolated input (Lo))Electrical Characterstics: Conforming to EIA RS-485Communication Method: Full duplexSynchronous Method: Start and StopTransmission Speed: 2400/4600/9600/19200 bpsStart Bit: 1 bitData Length : 7 bitsError Detection: Even parityStop Bit: 2 bitsCharacter Code: ASCII codeTransmission Control: No protocol

Analog Output (Isolated input (Lo))

Other FunctionsMoving Average: Digital Filter functionFixed Zero: 10˚digit is fixed to "0" for displayDisplay Blanking: Blanking of LEDs on main and

monitor displayTracking Zero: Zero point shift is digitally,

automatically corrected.Activated when digital zero functionbecomes valid

Resistive load Accuracy(23°C±5°C)Output

1 to 5V More than 10KΩ ±0.5% FS

4 to 20mA 0 to 500Ω ±0.5% FS

Signal Signal DirectionSignal name

Non-reversible output + Input/output

Reversible output – Input/output


Com

para

tor

SETPOINT COMPARATORAMH-762

Connection Diagram

Connection Diagram

Connector

Upper

Lower

GO LO LLHIHH

① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩

a (c)c (e) c (e) a (c) c (e) a (c) c (e) a (c) c (e) a (c)

(　)：PHOTO COUPLER

EXCP.SEL

HI LOA.B chA.A ch

V.B chV.A ch

INPUT

E AC POWER

① ② ③ ④ ⑤ ⑥ ⑦ ⑧

⑨ ⑩ ⑪ ⑫ ⑬ ⑭ ⑮ ⑯ ⑰

10 2 D.COM S/HA S/HB R.RE 0V　＋24V

90V～264V

Front

Side

Panel Cutout

Panel thickness:0.8 to 5.0mm

CONT

TZ PH DZ RE OL

HH HI GO LO LL

HS

P R M S

96

48

153

1317

161

17044.5

92

Min.120

Min

.70

＋0.8－0

45＋

0.6

－0

Dimensions

Ordering Code

AMH-762- VA - -

Comparator Output 1. Relay 2. Photo Coupler

1. None 2. TTL3. Open Collector

BCD Output

1. None 2. BCD3. RS-4854. RS-232C5. Analog Output (1 to 5V 4 to 20mA)

Output

Range

Power Supply 1. 90 to 264VAC

DZACLR NC

DZB NC

NC NCNC

NCNC

PHNC NCNC NC NC NC NC NCNC

NC NCNC NC NCNC NC NC NC NC NCNC

D.COM

D.COM

34

33

2

1

2 8 2 8 2 8 2 8

1 4 1 4 1 4 1 4

NC

DZBNC NC

DZACLROVER

POL PC

ENABLE 1

ENABLE 2

PH

34

33

2

1

100 101 102 103

100 101 102 103

2 8

1 4

104

104

COM

COM

DZH NCPHCLR

4ー20mA

4ー20mA

1ー5V

1ー5V

COM

DZB NC COM

34

33

2

1

NCNC NC NC NC NC NC NCNCNC

NCNC＋＋ー

＋ー

ー

＋ー

NC NCNC NC NC NC

25 1413 1

SG RTS TXDCTS RXD

D-SUB

NCNC SG＋－ TERMINATER

OFF ONRS485output

RS232Coutput

Analog output

Output Connector


ACV

&A

Ordering Code

Dimensions

Connection Diagram

AC Voltage Measurement

Accucracy: ±(0.3% of rdg. + 3 digit) (23°C ± 5°C, 35 ~ 85%RH)

AC Current Measurement

Accucracy: ±(0.5% of rdg. + 3 digit) (23°C ± 5°C, 35 ~ 85%RH)

SpecificationsInput Configuration: Single Ended input Impedance 10MΩ 100PF

or lessRectifier Circuit: Represents effective Value of sine wave by

demodulation of mean ValueConversion Rate: 2.5/secResponse Speed: Approx. 2.5sec(10~90%)Display: LED, 14.2mm 4 digitDecimal Point: Settable to any digit positionsOverrange Indication: When input exceeds the maximum display,

flash displayExternal Control: Hold; HOLD terminal and COM shortedPower Supply: AC90~132V

AC180~264VOperating Temperature: 0~50°C, 35 to 85%RHPower Consumtion: Approx. 2VADimensions: 48(H) × 96(W) × 95(D)mm DIN SizeWeight: Approx. 270gDielectric Strength: Between input terminal and earth(E),

DC500V/1 min. Between power supplyterminal and input terminal, COM, earth(E)AC1500V/1 min.


AC VOLTMETER & AMMETERAP-166

AP-166-

Power Supply 1. AC90~132V2. AC180~264V

Range 12

15

~ 22

25

~

-

48

96

① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ HI LO NC

INPUT

COM HOLD NC EAC POWER

Features

• Average


• AC 999.9mV~700.0V, AC 999.9mA~999.9mA

Measurement

Standard Type

FrequencyRange

999.9mV9.999V99.99V700.0V

Model RangeInput

ImpedanceInput

Protection

AP-166-12AP-166-13AP-166-14AP-166-15


100V100V300V700V

40Hz~10kHz40Hz~10kHz40Hz~4kHz40Hz~1kHz

FrequencyRange

999.9µA9.999mA99.99mA999.9mA

Model RangeInternal

ResistanceInput

Protection

AP-166-22AP-166-23AP-166-24AP-166-25

1kΩ100Ω10Ω1Ω

10mA50mA200mA

1A

40Hz~1kHz40Hz~1kHz40Hz~1kHz40Hz~1kHz

7195

6.5

92

Min.120M

in.7

0

＋0.8－0

45＋

0.6

－0

Front

Side

Panel cut


Upper


ACV

&A

AC VoltmeterAP-560

SpecificationsConversion Rate: 2.5/secOverrange Indication: noneDisplay: 3 digit, 14.2 mm Red LEDPower Consumption: 35 mA (MAX)Operating Temp.: 0 to 50˚C 35 to 85%RHDimensions: 96(W) 48(H) 22(D)mm DIN sizeWeight: Approx. 55 gDielectric Strength: input terminal/case, 1500 V DC/1 minInsulation Resistance: input terminal/case, more than 100 M ohm at

500 V DC

Features

•No need power supply

•Low cost

•Thin case, 1/8 DIN

Resolution

60 to 250 V AC240 to 600 V AC

Model Range Input Protection

AP-560-1AP-560-2

300 V700 V

1 V1 V


Ordering Code

AP-560-1. 60 to 250 V AC2. 240 to 600 V AC

Dimensions

Connection Diagram

Front

Side

Panel cutout

48

96

12.26.3

92

Min.120

Min

.70

＋0.8－0

45＋

0.6

－0

AC INPUT

Panel thickness 0.8 to 3.2 mm

Accuracy : ± 3 digits (23°C ± 5°C 35 to 85%RH)


ACV

&A

AC VOLTMETER & AMMETERA5-








99.99 mV999.9 mV9.999 V

Range MeasurementRange DisplayInput Frequency Maximum

Resolution Input Impedance Input Protection Accuracy

111213

04 10 µV100 µV1 mV

more than 1 MΩ40 Hz to 1 kHz100 V100 V250 V

±(0.2% of rdg + 10 digit)±(0.2% of rdg + 10 digit)±(0.2% of rdg + 10 digit)


9.999 mA99.99 mA999.9 mA



232425

08 1 µA10 µA100 µA

10 Ω1 Ω

0.1 Ω40 Hz to 1 kHz

100 mA500 mA

3 A



99.99 V600 V



1415

05 10 mV100 mV

more than 1 MΩ40 Hz to 1 kHz250 V600 V

±(0.2% of rdg + 10 digit)±(0.3% of rdg + 10 digit)


5A



2609

1 mA CT50 Hz or 60 Hz 8 A ±(0.5% of rdg + 10 digit)offset ±9999


Input configuration : Single endedResponse time : Approx. 1 sec.Crest factor : 4:1 at fullscale (only for TRUE-RMS)Dead zone : 0 to 99 digit

99.99 mV999.9 mV9.999 V



111213

06 10 µV100 µV1 mV

more than 1 MΩ40 Hz to 1 kHz100 V100 V250 V



9.999 mA99.99 mA999.9 mA



232425

10 1 µA10 µA100 µA

10 Ω1 Ω

0.1 Ω40 Hz to 1 kHz

100 mA500 mA

3 A



99.99 V600 V



1415

07 10 mV100 mV

more than 1 MΩ40 Hz to 1 kHz250 V600 V

±(0.2% of rdg + 20 digit)±(0.3% of rdg + 20 digit)


5A



2611

1 mA CT50 Hz or 60 Hz 8 A ±(0.5% of rdg + 20 digit)offset ±9999


AC Voltage, Current (TRUE-RMS)

AC Voltage, Current (Average)

Ordering Code

A5 -

Input

Output

Display board

Main board

0. None 1. HI & LO setpoint2. Analog output3. RS-232C 4. RS-4855. HI & LO setpoint + analog output6. HI & LO setpoint + analog output + RS-232C7. HI & LO setpoint + analog output + RS-485

1. Single 2. Multiple

1. AC100 - 240 V (±10%) 2. DC9 - 60 V

04. AC voltage AVG (99.99 mV to 9.999 V) 05. AC voltage AVG (99.99 V to 600 V)06. AC voltage RMS (99.99 mV to 9.999 V)07. AC voltage RMS (99.99 V to 600 V)08. AC current AVG (9.999 mA to 999.9 mA)09. AC current AVG (5 A)10. AC current RMS (9.999 mA to 999.9 mA)11. AC current RMS (5 A)

Features

•Low Cost


DC9~60 V


Proc

ess

Mon

itor

Ordering code

Dimensions

Connection Diagram



SpecificationsMeasurement function :DC voltage & current measurement.Front

Specify one model from among 4 models.Operation method : Dual slopeInput configuration : Single endedInput Bias Current : 2nA(Typ.)Conversion rate : 2.5 times/sec Normal mode rejection :More than 4dB (50/60Hz) (Typ.)Max.display : 1999Overrange indication : When input exceeds the maximum display,

1999 or -1999 flashesDisplay : LED, 14.2mm, 3 1/2-digitsPolarity : Automatic polarity selectionPolarity display : A “–” is displayed automaticallyExternal control : Hold;COM terminal and S/H terminal shorted Side

or level “0”Decimal point : Settable to any digit positionOperation Temperature/humidity : 0 ~ 50˚C, 35 to 85%RHStorage temperature/humidity : -10 ~ 70˚C, 60%RH max.Power supply : AC 90V~132V 50/60Hz 2.0VA(Max.) (100V)

180V~264V 50/60Hz 2.0VA(Max.) (200V)DC 24V ±20% 40mA(Max.) Isolated

Dimensions : 96mm(W) x 48mm(H) x 71mm(D) DIN sizeWeight : AC Approx. 175g DC Approx. 100gDielectric resistance : AC type; Between power supply and input

terminal(Lo),COM,case, AC2100V/1 min.DC type; Between power supply(0V) andinput(Lo), DC500V

Insulation resistance : Between power supply terminal(0) andinput(Lo) DC500V more than 100M ohm

Accessory : Instruction manual, terminal cover,2-axis,2-screwStandards : IEC1010-1,EN50082-2,EN50081-2Setup environment : Installation category II, Pollution degree 2Altitude : 2000m max.Fuse : Type TR-5 19372-0.2A Slow-blow type

DIGITAL SCALING METERAS-101

Features• Low Cost

• CE Approval

1~5V0~5V

0~10V

Offset ±10Fullscale 100~1999

1MΩ ±100VAS-101-1VAS-101-2VAS-101-3V

DisplayAdjustable

InputImpedance

InputProtection

Model Range

Accuracy : ±(0.1% of rdg. + 2 digits) (23°C ±5°C, 35~85%RH)

4~20mAOffset ±10Fullscale 100~1999

51Ω ±70mAAS-101-2A

DisplayAdjustable

InputImpedance

InputProtection

Model Range

Accuracy : ± (0.1% of rdg. + 2 digits) (23°C ±5°C, 35~85%RH)

Power supply

Range

1: AC 90~132V2: AC 180~264V4: DC 24V (Isolated)

1V: 1~5V2V: 0~5V3V: 0~10V2A: 4~20mA

AS-101- -

48

96

71566.5

92＋0.8－0

45＋

0.6

－0

Front

Side

Panel cut

① ② ③ ④ ⑤ ⑥ ⑦ ⑧

INPUT AC/DC POWER

HI LO NC S/H 0V +VCOM

NC


ProcessM

onitor

Ordering Code

Dimensions

Connection Diagram


Accuracy: 0.1% rdg. ±2 digits (23°C ±5°C)


Accuracy: ±0.2% rdg. ±2 digits (23°C ±5°C)±0.3% rdg. ±1 digit only for AS-203A-25

1~5V Measurement

Accuracy: ±0.1% rdg. ±2 digits (23°C ±5°C)

4~20mA Measurement

Accuracy: ±0.1% rdg. ±2 digits (23°C ±5°C)

SpecificationsInput Configuration: Single EndedInput Bias Current: 2nA (Typ.)Conversion Rate: 2.5/secNormal Mode Rejection: 40dB (Typ.) (50/60Hz)Temperature Coefficient: Offset Typ. ±0.1, Max. ±0.3 digit/°C

Fullscale Typ. ±0.1, Max. ±0.3 digit/°CDisplay: LED, 8mm 3 1/2 digitsPolarity: A "-" is displayed automaticallyDecimal Point: Settable to any digit positionOverrange Indication: When input exceeds the maximum display,

1999 flashesFullscale Adjustment: 100~1999Offset Adjustment: ±1000Span: 2000 countsPower Supply: DC5V ±5%, 90mA (Typ.)

DC24V ±20%, 20mAOperating Temperature: 0~50°C, 35 to 85%RHPower Consumption: 450 mW at 5V, 480 mW at 24VDimensions: 24(H) × 48(W) × 73(D)mm DIN SizeWeight: Approx. 46gDielectric Strength: Between power supply (0V) terminal and input

(Lo) terminal, DC500VBetween input (Lo) terminal and mountingpanel, AC1500V/1 min.


PROCESS MONITORAS-203A

AS-203A-Power Supply

-3. DC 5V (Isolated)4. DC 24V (Isolated)

11

14Range

~ 21

25

~ 1V

2A

~

5173

4.8

48

24

FullscaleAdjust

Offset Adjust

1 2

LOHI BL COM OV +5. 24V

PowerINPUT

Sta

rt/H

old

3 4 5 6 7 8 9 10

Features

• Easily adjustable offset-fullscale from the front panel

(Span 2000 counts)

• Bright LED, 8mm (Red)

• DIN size 24(H) × 48(W)mm

• Power supply DC5V or DC24V (Isolated)


• 1~5V, 4~20mA Measurement

Miniature Size

±199.9mV±1.999V±19.99V±199.9V

Model RangeInput

ImpedanceInput

Protection

AS-203A-11AS-203A-12AS-203A-13AS-203A-14

Offset ±1000

Fullscale ±100~1999


±100V±250V±250V±500V

DisplayAdjustable

±199.9µA±1.999mA±19.99mA±199.9mA±1.999A

Model RangeInternal

ResistanceInput

Protection

AS-203A-21AS-203A-22AS-203A-23AS-203A-24AS-203A-25

Offset ±1000

Fullscale ±100~1999

1kΩ100Ω10Ω1Ω

0.1Ω

±10mA±50mA

±150mA±500mA

±3A

DisplayAdjustable

1~5V

Model RangeInput

ImpedanceInput

Protection

AS-203A-1V Offset ±1000Fullscale 100~1999 1MΩ ±250V

DisplayAdjustable

Min.65

Min.3522.2

＋0.3

－0

45＋0.6 －0

Front

Side

Panel cut


4~20mA

Model RangeInternal

ResistanceInput

Protection

AS-203A-2A Offset ±1000Fullscale 100~1999 51Ω ±70mA

DisplayAdjustable


Proc

ess

Mon

itor

Ordering Code

Dimensions

Connection Diagram

LOHIOV +5V

D.P

COM

Connect input Lo and Ov.

Power

INPUT

HO

LD

1 2 3 4 5 6 7 8 9 10

101 102 103

48

73

514.8

24

Fullscale Adjust

Offset Adjust

Min.65

Min

.3522

.2+

0.3

–0

45+0.6–0

Front


Side

Panel Cutout

AS-201 -

1V2V3VRange


Accuracy: ±0.1% rdg ±2 digit (23°C ±5°C)

SpecificationsInput Configuration: Single EndedInput Bias Current: 2nA(Typ.)Conversion Rate: 2.5/secNormal Mode Rejection: 40dB Typ. (50/60Hz)Temperature Coefficient: ±0.1 digit (Typ.)/°C

±0.3 digit (Max.)/°CDisplay: LED, 10.2mm 3 1/2 digitPolarity: 1V Range:When input less than 1V, a "-" is

displayed automatically.2V, 3V Range:When input less than 0V, a "-"is displayed automatically.

Decimal Point: Settable to any digit positionOverrange Indication: When input exceeds the maximum display,

1999 flashesFull-scale Adjustment: 100~1999External Hold: Negative 0V or ShortPower Supply: DC 5V±5% 70mA (Typ.)Operating Temperature: 0~50°C, 35 to 85%RHPower Consumption: 350mWDimensions: 24(H) 48(W) 73(D)mm DIN SizeWeight: 40gDielectric Strength: Between Input(Lo) and Mounted panel,

AC1500V/1 min.Insulation Resistance: DC500V 100MΩ or more at above terminals

1~5V0~5V

0~10V

Model Code RangeInput

ImpedanceInput

Protection

AS-201-1VAS-201-2VAS-201-3V

1MΩ1MΩ1MΩ

±250V±250V±250V

0-100~19990-100~19990-100~1999

DisplayAdjustable

PROCESS MONITORAS-201

Features• Adjustable full scale

• Bright LED 10.2mm

• Din size 24(H) 48(W)

• 1-5V, 0-5V, 0-10V measurement

• Power supply DC5V (NO-ISOLATED)

Fullscale Adjustable


ProcessM

onitor

Dimensions

Connection Diagram

INPUT EARTH

Hi Lo (E)

DECIMAL POINT

103 102 101

96

48

Offset VR

Fullscale VR

2212.26.3

Min.120

Min.70

92 ＋0.8 －0

45＋0.6

－0

Panel thickness 0.8~3.2mm

Front

Side

Panel Cutout

4~20mA Measurement

Accuracy: ±0.1% F.S. ±1 digit (23°C ±5°C)

SpecificationsInput Configuration: Single EndedMax. Display: 1999Conversion Rate: 2.5/secNormal Mode Rejection: NMR 40dB (TYP)Temperature Coeficient: Offset display, ±0.3 digit/°C (Max.)

Fullscale display,±0.3 digit/°C (Max.)Overrange Indication: When input exceeds the maximum display,

display +1 and blank other digitsFullscale Adjustment: 100 to 1999Offset Adjustment: ±200 digitsVoltage Drop: 2.2V (at 20mA) Typ.

1.6V (at 4mA) Typ.Display: LCD, 12.7mm Polarity: A "-" is displayed automaticallyDecimal Point: Settable to any digit positionPower Supply: Current loop power (4 to 20mA)Operating Temperature: 0 to 50 °C, 35 to 85% RHDimensions: 48(H) 96(W) 22(D)mm DIN sizeWeight: Approx. 55 g (unit only)Dielectric Strength: Input (Lo) terminal and earch(E),

500VDC/1min.Accessory: Instruction Manual

Ordering Code

AL-501A

4~20mA

Model RangeInput

Protection

AL-501A Offset ±200Fullscale 100~1999 ±50mA

DisplayAdjustable

PROCESS MONITORAL-501A

Features• Self power (4~20mA)

• Easily adjustable for offset-fullscale from the front panel

• LCD Display, 12.7 mm

• Screw terminals

• 4~20mA Measurement

Self Power(4 to 2omA)


Proc

ess

Mon

itor

PROCESS MONITORAL-213

SpecificationsInput Configuration: Single endedMax. display: 1999Conversion rate: 2.5/sec (TYP)Normal mode rejection: 40 dB (TYP)Temperature Coefficient: Offset display, ±0.3 digit/˚C

Fullscale display, ±0.3 digit/˚COverrange indication: When input exceeds the maximum display, display 1

and blank other digitsFullscale adjustment: 100-1999Offset adjustment: ±200Voltage drop: 5 V at 4 mA

5.3 V at 20 mADisplay: LED (red), 10.16 mmPolarity: A "-" is displayed automaticallyDecimal point: Settable to any digit positionOperating temp.: 0 -50˚C 35-85%RHDimensions: 48 (W) 24 (H) 40 (D) mm DIN sizeDielectric strength: Between input (LO) and earth (E) DC500 V/minWeight: approx. 55 g

Ordering codeAL-213

Features

•Self power (4-20mA)

•LED display 10.16mm (red)

•Screw terminal

Display4-20mARange Input ProtectionModel

AL-213

Accuracy: ± (0.1% of FS + 1 digit) (23 ± 5) 35-85%RH

± 50mAOffset ± 200Fullscale 100-1999

4-20mA Measurement Dimensions

Connection Diagram

Front

Side

24

48

10.16

4.3

57.7

39.7

Rear

45

65mm以上

35mm以上

＋0.6－0

22.2＋

0.3－

0

1 2 3


Terminal No. 1 Input HI2 Input LO3 Earth

Panel cutout


ProcessM

onitor

Dimensions

Connection Diagram

4~20mA Measurement

Accuracy: ±(0.1% of FS + 1 digit) (23°C ±5°C, 35 to 85% RH)

SpecificationsInput Configuration: Single endedMax. Display: 1999Conversion Rate: 2.5/secNormal Mode Rejection: NMR 40dB (TYP)Temperature Coeficient: Offset display, ±0.3 digit/°C

Fullscale display, ±0.3 digit/°COverrange Indication: When input exceeds the maximum display,

display 1 and blank other digitsFullscale Adjustment: 100 to 1999Offset Adjustment: ±200Voltage Drop: 5V at 4 mA

5.3V at 20 mADisplay: LED, 14.2 mm Polarity: A "-" is displayed automaticallyDecimal Point: Settable to any digit positionOperating Temp: 0 to 50°C, 35 to 85% RHDimensions: 96(W) × 48(H) × 22(D)mm DIN sizeWeight: Approx. 55 g (unit only)Dielectric Strength: Input (Lo) and earth(E), 500VDC/1 min.Accessory: Instruction Manual, terminal cover.

Ordering Code

AL-512

PROCESS MONITORAL-512

48

96

92

Min.120M

in.7

0

＋0.8－0

45＋

0.6

－0

Front

Side

Panel cut

INPUT EARTH

Hi Lo (E)

Features

• Self power (4~20mA)

• LED display 14.2 mm (red)

• Screw terminal

4~20mA

Model RangeInput

Protection

AL-512 Offset ±200Fullscale 100~1999 ±50mA

Display

22

12.26.3



Ther

mom

eter

PROCESS MONITORAS-243


Dimensions

Connection Diagram

Front

Side

Panel Cutout


24

48

87

655

45

Min.65

Min

.35

＋0.6－0

22.2＋

0.3

－0

1 2

LOHI NC NC NCNCCOMS/H －＋

DC POWERINPUT

3 4 5 6 7 8 9 10

Features

•Easily adjustable offset-fullscale (Span 10000 counts)

•Bright LED, 8 mm (Red)

•DIN size 24 (H) 48 (W) mm

•Power supply DC 24 V (isolated)

•1-5 V, 0-5 V, 0-10 V, 4-20 mA measurement


General SpecificationsInput configuration : Single endedInput bias current : 2 mA (TYP.)Conversion rate : 2.5/secNormal mode rejection : 50dB (TYP.) (50/60 Hz)Temp. coefficient : Offset display ±0.5 digit/˚C

Fullscale display ±0.01% of span/˚COverrange indication : When input exceeds the maximum display,

display flashesFullscale adjustment : 100 to 9999Offset a djustment : ±5000Span : 10000 countsDisplay : LED, 8 mm (Red)Polarity : A "-" is displayed automaticallyScaling : By switch (rear) and fine volume (front)Hold : COM and S/H terminal shortedDecimal point : Settable to any digit positionOperating temperature : 0 to 50˚C 35 to 85%RHPower supply : DC24V±20%Power consumption : 30 mA at DC24VDimensions : 24(H) 48(W) 87(D)mm DIN sizeWeight (unit) : Approx. 50gDielectric strength : Between input (Lo) and mounted panel, AC

1500V/l min.Between input (Lo) and power supply (0V), DC500 V/l min.

Insulation resistance : DC 500 V 100 MΩ or more at the aboveterminals

Accessory : Connector, Instruction manual

Model Range Display Input Impedance Input ProtectionAS-243-1V 1-5 V Offset ±5000 1MΩ ±250VAS-243-2V 0-5V fullscale 1MΩ ±250VAS-243-3V 0-10 V 100 to 9999 1MΩ ±250V

Accuracy: ±(0.1%of rdg+2 digit) (23˚C±5˚C 45~75%RH)

DC Current MeasurementModel Range Display Internal Resistance Input Protection

AS-243-2A 4-20mA Offset ±5000 50Ω ±50mAfullscale100 to 9999

Accuracy: ±(0.1% of rdg+2 digit) (23˚C±5˚C 45~75%RH)

Ordering Code

AS-243 4-

Power Supply

-

Range

4. DC24V

1V2V3V2A


Thermom

eterTHERMOMETER

A5-








KKJTSRB

Range SensorType

–50.0 to 199.9°C–50 to 1200°C–50 to 1000°C–50 to 400°C0 to 1700°C

–10 to 1700°C100 to 1800°C

MeasurementRange

MaximumResolution Accuracy

KAKBJTSRB

13

0.1°C1°C1°C1°C1°C1°C1°C

±(0.5% of FS)±(0.2% of FS)±(0.2% of FS)±(0.6% of FS)±(0.4% of FS)±(0.4% of FS)

±(0.4% of FS) over 500°Cavailable Fahrenheit display

Cold junction compensator accuracy : ±1°C (10 to 40°C)Sensor lead resistance : Less than 50 ΩLinearizing method : Digital linearizingBurn out alarm : ———

PT100 ΩPT100 Ω

Range SensorType

–100.0 to 199.9°C–100 to 600°C

MeasurementRange


PAPB

14 0.1°C1°C

±(0.15% of FS)±(0.3% of FS)

available Fahrenheit displayCurrent for resistance : Approx. 1 mAExternal lead resistance : Less than 10 Ω/leadLinearizing method : Digital linearizingBurn out alarm : ———

RTD

Thermocouple Ordering Code

A5 -

Input

Output

Display board

Main board



1. AC100 - 240 V (±10%) 2. DC9 - 60 V

13. Temperature (Thermocouple) 14. Temperature (RTD)

Dimensions

92

96

487

121

45

147.

5

45+

0.6

-0

92 +0.8- 0

MIN

.70

MIN.120

Features

•Low Cost


DC9~60 V

•Sensor Type :K, J, T, S, R, B, PT100 Ω


Ther

mom

eter

Ordering Code

Dimensions

Connection Diagram

TC Measuring Range

RTD Measuring Range

SpecificationsInput Configuration: Single EndedConversion: 2.5/secNormal Mode Rejection: 40dB (Typ.)Display: LED, 8mm 3 1/2 digitPolarity: A "-" displayed automaticallyPower Supply: DC5V ±5% 90mA

DC12V ±20% 40mADC24V ±20% 20mA

Operating Temperature: 0~50°C, 35 to 85%RHDimensions: 24(H) × 48(W) × 66(D)mm DIN SizeWeight: Approx. 51gDielectric Strength: Between Input (A, B, COM) and 0V terminal,

DC500VInsulation Resistance: DC500V 100MΩ at above terminals

TC Measurement SectionSensor: K or JTemperature Display: °C or °FResolution: 1°C or 1°FExternal Lead Resistance: Less than 100ΩCold Junction Compensator Accuracy: ±2°C (10°C~40°C)Burn-out Alarm: -1999 FlashingExcessive Input: DC ±5V

RTD Measurement SectionSensor: PT-100ΩCurrent for Resistance: 1mA (Typ.)Temperature Display: °C or °FResolution: 0.1°C or 1°C, 1°FExternal Lead Resistance: Less than 1Ω/leadLinearizing Method: Analog Linearizing

Analog Output SectionVoltage: 1mV/°C or 1mV/°F, 10mV/°C for PAAccuracy: ±2% F.S. (23°C ±5°C)External Lead Resistance: More than 20kΩ

THERMOMETERAT-205

AT-205-Output

-

Code

3. DC5V (Isolated)4. DC24V (Isolated)5. DC12V (Isolated)

1. None3. Analog

Power Supply

PAPFPJ

KCJCKFJF

48

24

45

Min.65

Min

.35

＋0.6－0

22.2＋

0.3

－0

Front

Side

Panel cut

HOLDCOM

OUTT.C.

RTDPt

A B0V

ANALOG DC POWER5V/12V/24

① ② ③ ④ ⑤ ⑥ ⑦

＋

Features

• Small Size

• Power Supply DC5V, DC12V, DC24V

• Sensor Types K, J, and PT-100Ω• Analog Output (option)

• Screw Terminal

• Bright LED, 8mm (Red)

Miniature Size

0°C~+1000°C+32°F~+1832°F

0°C~+400°C+32°F~+752°F

Sensor Measuring RangeAccuracy

(23°C±5°C)

K

J

1°C1°F1°C1°F

±0.8% F.S.±0.8% F.S.±0.8% F.S.±0.8% F.S.

Code

KCKFJCJF

Resolution

-100.0°C~+199.9°C-200°C~+600°C-328°F~+1112°F

Sensor Measuring RangeAccuracy

(23°C±5°C)

PT-100Ω0.1°C1°C1°F

±0.2% F.S.±0.4% F.S.±0.4% F.S.

Code

PAPJPF

Resolution

66

514.8



StrainG

augeSTRAIN GAUGE METER

A5-








–0.3 to +2 mV/V

PowerSupply

for Sensor

ZeroAdjustment

Range

1 to 3 mV/V

SpanAdjustment

Range


5 V10 V

170.5 µV/digit1 µV/digit

±(0.1% of FS) +2 digit

Sensor : 350 ΩPower supply for sensor : 5 V±5% (less than 15 mA)

10 V±5% (less than 30 mA)

HIGOLO

Setting range : –9999 to 9999Hysteresis : 1 to 999 digit for each setpointsRelay contact capacity : AC240 V 8 A resistive load

DC30 V 8 A resistive load

Indication > High setpointHigh setpoint Indication Lo setpointIndication < Lo setpoint

Output

HI & LO setpoint output (A5XX1-XX)

±(0.5% of FS)

Output method : PWM methodScaling : Digital scaling

0 to 1 V0 to 10 V1 to 5 V

4 to 20 mA

more than 10 kΩmore than 10 kΩmore than 10 kΩless than 550 Ω

Output Resistive load Accuracy

Analog output (A5XX2-XX)

Communication method : Full duplexTransmission speed : 2400/4800/9600/19200/38400 bpsStart bit : 1 bitData length : 7 bit/8 bitParity : Even parity/odd parityStop bit : 1 bit/2 bitCharacter code : ASCII codeTransmission control process : lgnored process

RS-232C (Conforming to EIA RS-232C) (A5XX3-XX)

Communication method : Full duplexTransmission speed : 2400/4800/9600/19200/38400 bpsStart bit : 1 bitData length : 7 bit/8 bitParity : Even parity/odd parityError detection : BCCStop bit : 1 bit/2 bitCharacter code : ASCII codeTransmission control process : lgnored processSignal name : + non reversal output

– reversal outputMaximum No. of meter connected : 31Line length : Up to 500 m in total

RS-485 (Conforming to EIA RS-485) (A5XX4-XX)

Strain Gauge

Ordering Code

A5 -

Input

Output

Display board

Main board



1. AC100 - 240 V (±10%) 2. DC9 - 60 V

1 7

Dimensions

92

96

487

121

45

147.

5

45+

0.6

-0

92 +0.8- 0

MIN

.70

MIN.120


Stra

inG

auge

Dimensions

Connection Diagram

SpecificationsAccuracy: 0.1%FS ±1 digitConversion Rate: 2.5/secNormal Mode Rejection: NMR 40dB (Typ) (50/60Hz)Sensor: Strain gauge sensor (350W)Excitation Supply: DC5V±5% 20mADisplay: LED, 8mm (RED)Decimal Point: Settable to any digit positionOverrange Indication: When input exceeds the maximum display,

1999 flashesPower Supply: DC19 to 29V (40mA at DC24V)Operating Temperature: 0 ~ 50°C, 30 ~ 85%RHPower Consumption: Approx. 1WDimensions: 24(H) × 48(W) × 87(D) mm DIN SizeWeight: Approx. 53g (unit only)Dielectric Strength: Between power supply/COM DC500V/ 1 min.

Between -SIG/case AC1500V/ 1 min.Insulation Resistance: DC500V 100MW at above terminalsAccessory: Instruction manual, connectorZero Adjustment: ±0.3mV/VGain Adjustment: 1mV/V~3mV/V to fullscale 1999Zero Drift: 0.02% FS/°CGain Drift: 0.02% rdg/°CAnalog Output: 1mV/digit

0.5% FS, less than 250ppm more than100msec, more than 500W

External Control: Hold

Comparator SectionSetting Range: 10~+1999 (HI and LO)Setting Method: By VolumeSetting Accuracy: Setting value ±2 digit (23°C ±5°C) (Typ.)Relay Contact Capacity: 250VAC 0.1A resistive load

120VAC 0.5A resistive load28VDC 1A resistive load

Comparative Condition: HI setpoint%Indication HILO setpoint.Indication LO

Hysteresis: 5~12 digitResponse Time: less than 100msec

Ordering Code

ASG-251

STRAIN GAUGE METERASG-251

HI LO

48

24

Min.65Min.35

45 ＋0.6 －0

22.2

＋0.3

－0

Front

Side

Panel cut

COMa c b HOLD

POWER

0V +24Va c

Lo

b

HI

1 2 3 4 5 6 7 8 9 10

Features

• Hi and Lo Set points

• Bright LED, 8mm (RED)

• Excitation Supply 20mA at DC5V

Load Cell Direct Input

22 21

87


NCNCCOM－EXC+EXC－SIG

INPUT

+SIG NC COMANALOG OUT

1 2 3 4 5 6 7 8 9 10

Upper

Lower


A7000

A7000 SERIES DIGITAL PANEL METERA7000

Features


12 to 48VDC

• Panel cut out 72mm(W) 36mm(H)

• Option BCD output, RS-232C, RS-485

• HH, HI, GO, LO, LL setpoints

• Input DC, AC, TC, RTD, Frequency, Strain Gauge

Resistance

Common SpecificationMaximum display: 9999Overrange indication: When input exceed the maximum display

display OVER or –OVERZero display: Leading zero suppressionDecimal point: Settable to any digit positionOperating temp: 0 to 50°C(35 to 85% RH)Storage temp.: –10 to 70°C less than 60%RHPower supply: 100 to 240VAC±10%

12 to 48VDC ±10%Power consumption: 8VA(At AC) 7W(At DC)Dimensions: 72mm(W)X36mm(H)X118mm(D)Weight:approx: 160gDielectric strength(AC): Power supply/input terminal/output terminal

AC1500V/min(DC): Power supply/input terminal/output terminal

DC500V/minInput terminal/output terminal DC500V/min

Insulation resistance: DC500V more than 100M Ω at the aboveterminals

A7X11-X

±99.99mV±999.9mV±9.999V±99.99V±700V

Display

±50V±50V

±250V±250V±700V

1112131415

±(0.03% of rdg+1digit)


offset ±9999full scale ±9999

Range Measurement Range InputProtection

Accuracy(23°C±5°C,35~85%RH)

Conversion rate: 100times/sec

Input Specifications

DC voltage, current

A7X12-X

±99.99µA±999.9µA±9.999mA±99.99mA

Display

±10mA±50mA±50mA

±700mA

21222324

±(0.1% of rdg +2 digit)offset ±9999full scale ±9999




A7X13-X

±999.9mA±2.000A

Display

±3A2526





AC voltage, current (TRUE-RMS)

A7X14-X

99.99mV999.9mV9.999V99.99V700.0V

Display

50V50V250V250V700V

1112131415




±(0.2% of rdg +20 digit)

±(0.3%of rdg +20 digit)

Minimum display 50 digitsFrequency range: 40Hz to 1kHzResponse time: Approx 1 sec(10% to 90%)Conversion rate: 1000times/sec

A7X15-X

99.99µA999.9µA9.999mA99.99mA

Display

10mA50mA50mA500mA

21222324

±(0.5%of rdg +20 digit)offset ±9999full scale ±9999




A7X16-X

999.9mA5A

Display

3A8A

2526





Resistance

A7X17-X

99.99Ω999.9Ω9.999kΩ99.99Ω

Display

5mA0.5mA50µA5µA

11121314


Range Measurement Range Current Accuracy(23°C±5°C,35~85%RH)

±(0.1% of rdg + 4 digit)

Conversion rate: 100times/secMeasurement method: Two or Four wire (internal socket changable)

NEW!


A70

00

Thermocouple · RTD

A7X18-X

KKJTSRB

PT100ΩPT100Ω


–10 to 1700°C100 to 1800°C

–100.0 to 199.9°C–100 to 600°C

MeasurementRange

0.1°C1°C1°C1°C1°C1°C1°C

0.1°C1°C

± (0.5% of FS)± (0.2% of FS)± (0.2% of FS)± (0.6% of FS)± (0.4% of FS)± (0.4% of FS)± (0.4% of FS)

± (0.15% of FS)± (0.3% of FS)

KAKBJTSRB

PAPB

Range Sensor type MaximumResolution


available Fahrenheit display

Cold junction compensator accuracy: ±2°C(10 to 40°C)Sensor lead resistance: less than 50ΩLinearzing method: Digital linearizingBurn out alarm: - - - - -Conversion time: 2.5times/sec

Frequency

A7X19-X

0.1 to 999.9Hz 1 to 9.999kHz10 to 99.99kHz

111213

±(0.2% of FS)

Range Measurement Range Accuracy(23°C±5°C,35~85%RH)

L:less than 1.5V(5V, pullup)L:less than 1V, HI:2.5 to 15V

0.3 to 30V P-P30V rms to 500V rms

30V15V30V500V

Open collectorLogic

MagentVoltage

Input type Input voltage level Input Protection

Prescale: 0.01~10.00PPR: 1~100Power supply for sensor: 12VDC±10%

Strain gauge

A7X1A-X

–1 to +1mV/V 1 to 3mV/V

Span adjustmentrange

–4~+4mV/V ±(0.1% of FS)+2 digit

5V10V

Sensor Zero adjustmentrange

Measurementrange Accuracy

Sensor: 350 ΩPower supply for sensor: 5 V±5% (less than 15 mA)

10 V±5% (less than 30 mA)Conversion speed: 1000/sec

Process

A7X1B-X

1 to 5V±5V

4 to 20mA±20mA

Display

1V2V2A3A


Range MeasurementRange Accuracy

±(0.03% of rdg +2digit

±(0.1% of rdg +3digit

Conversion rate: 1000times/secExcitation power supply: 12VDC ± 5%

24VDC ± 5% 25mA

Indication > High High setpointHigh High setpoint>=Indication>High setpoint

High setpoint>=Indication>=Lo setpointLow setpoint>Indication>=Low Low setpoint

Low Low setpoint>Indication

HHHIGOLOLL

Setting range: –9999 to 9999Hysteresis: 1 to 999 digit for each setpointsRelay contact capacity: AC125V 0.3A resistive load

DC30V 1A resistive loadPhotocoupler capacity: DC30V 50mA

Output Specification

HH,HI & LO, LLsetpoints outputComparative condition :

BCD outputType of output: Open collector or TTLLogic: ChangeableOutput rate: DC30V 10mA(open collector)

Funout 2(TTL)

Analog output (PWM)

more than 10kΩ

less than 550Ω

±(0.5% of F.S)50mV p-p

25mV p-p

0 to 1V0 to 10V1 to 5V

4 to 20mA

Output Load resistance Accuracy Ripple

Output method: PWM methodScaling: Digital scalingResolution: 13 bitResponse time: approx 0.5sec

RS232C (Conforming to EIA RS-232C)Communication method: Full duplexTransmission speed: 4800/9600/19200/38400 bpsStart bit : 1 bitData length: 7 bit/8 bitParity: Even parity/ odd parityStop bit: 1 bit/2 bitCharacter code: ASCII codeTransmission control process: Ignord process

RS-485 (Conforming to EIA RS-485)Communication method: Full duplexTransmission speed: 4800/9600/19200/38400 bpsStart bit: 1 bitData length: 7 bit/ 8 bitParity: Even parity/ odd marityError detection: BCCStop bit: 1 bit/2 bitCharacter code: ASCII codeTransmssion control process: Ignord processSignal name: + non reversal output

– reversal outputMaximum no of meter connected: 31Line length: up to 500m in total



A7000

Ordering CodeA 7 1 –

Output

Input

0. none1. Relay output2. Photocoupler output3. BCD output (TTL)4. BCD output (Open collector)5. BCD output (TTL), Photocoupler output6. BCD output (Open collector),

Photocoupler output7. Analog output8. Analog output, Photocoupler output9. RS-232CA. RS-485B. RS-232C, Photocoupler outputC. RS-485, Photocoupler output

1. DC voltage2. DC current3. DC current4. AC Voltage5. AC current6. AC current7. Resistance8. Temperature (T/C, RTD)9. FrequencyA. Strain gaugeB. Process

Power supply 1. AC100 to 240V2. DC12 to 48V

Dimensions

68

80

87

72

36

7

118

33

HHHIGOLOLL

REPHDZMEP1P2P3

ME

Min.96

68+0.7–0

33–0 +

0.6



A60

00A6000 SERIES DIGITAL PANEL METER

A6000 Features


12 to 48VDC

• Panel cut out 96mm(W) 48mm(H)

• Option BCD output, RS-232C, RS-485

• HI, GO, LO 2 setpoints, Analog output

• Input DC, AC, TC, RTD, Frequency, Strain Gauge

Resistance

Common SpecificationDisplay: Main display Red or Green LED 20 mm

Sub display Red LED 6 mmConversion rate: 1000 times/sec.Maximum display: 9999Overrange indication: When input exceed the maximum display

display OVER or –OVERZero display: Leading zero suppressionDecimal point: Settable to any digit positionOperating temp.: 0 to 50°C 35 to 85%RHStorage temp.: –10 to 70°C less than 60%%RHPower supply: AC 100 to 240 V ±10%

DC 12 to 48 V ±10%Power consumption: 8 VA (max. load)Dimensions: 96 mm(W)X 48 mm(H)X 97.5 mm(D)DIN sizeWeight: approx. 450 gDielectric strength(AC): Power supply/input terminal/output terminal

AC1500 V/min.(DC): Power supply/input terminal/output terminal

DC500 V/min.(Common): Case/each terminal

AC1500 V/min.Insulation resistance: DC500 V more than 100 MΩ at the above

terminals

A6XX1-XX

±99.99mV±999.9mV±9.999V±99.99V±700V

Display

±50V±50V

±250V±250V±700V

1112131415







DC voltage, current

A6XX2-XX

±99.99µA±999.9µA±9.999mA±99.99mA

Display

±10mA±10mA±50mA

±500mA

21222324




A6XX3-XX

±999.9mA±2.000A

Display

±3A2526




AC voltage, current (TRUE-RMS)

A6XX4-XX

99.99mV999.9mV9.999V99.99V700.0V

Display

50V50V250V250V700V

1112131415




±(0.2% of rdg +20 digit)

±(0.3%of rdg +20 digit)

Minimum display 50 digits

A6XX5-XX

99.99µA999.9µA9.999mA99.99mA

Display

10mA50mA50mA500mA

21222324





A6XX6-XX

999.9mA5A

Display

3A8A

2526





Resistance

A6XX7-XX

99.99Ω999.9Ω9.999kΩ99.99kΩ

Display

5mA0.5mA50µA5µA

11121314


Range Measurement Range Current Accuracy(23°C±5°C,35~85%RH)

±(0.1% of rdg + 4 digit)

Measurement method: Two or Four wire (internal socket changable)

NEW!

(Multiple) (Single)


A6000

65


Thermocouple · RTD

A6XX8-XX

KKJTSRB

PT100ΩPT100Ω


–10 to 1700°C100 to 1800°C

–100.0 to 199.9°C–100 to 600°C

MeasurementRange

0.1°C1°C1°C1°C1°C1°C1°C

0.1°C1°C

± (0.5% of FS)± (0.2% of FS)± (0.2% of FS)± (0.6% of FS)± (0.4% of FS)± (0.4% of FS)± (0.4% of FS)

± (0.15% of FS)± (0.3% of FS)

KAKBJTSRB

PAPB

Range Sensor type MaximumResolution


available Fahrenheit display Cold junction compensator accuracy : ±2°C(10 to 40°C)Sensor lead resistance: : less than 50ΩLinearzing method: : Digital linearizingBurn out alarm: : - - - - -Conversion time: : 2.5times/sec

Frequency

A6XX9-XX

0.1 to 999.9Hz 1 to 9.999kHz10 to 99.99kHz

111213

±(0.2% of FS)

Range Measurement Range Accuracy(23°C±5°C,35~85%RH)

L:less than 1.5V(5V, pullup)L:less than 1V, HI:2.5 to 15V

0.3 to 30V P-P30V to 500V rms

30V15V30V500V

Open collectorLogic

MagentVoltage

Input type Input voltage level Input Protection

Prescale : 0.01~10.00PPR : 1~100Power supply for sensor : 12VDC±10%

Strain gauge

A6XXA-XX

–1 to +1mV/V 1 to 3mV/V

Span adjustmentrange

–4~+4mV/V ±(0.1% of FS)+2 digit

5V10V

Sensor Zero adjustmentrange

Measurementrange Accuracy

Sensor : 350 ΩPower supply for sensor : 5 V±5% (less than 15 mA)

10 V±5% (less than 30 mA)Conversion speed : 1000/sec

Process

A6XXB-XX

1 to 5V±5V

4 to 20mA±20mA

Display

1V2V2A3A


Range MeasurementRange Accuracy

±(0.03% of rdg +2digit)

±(0.1% of rdg +3digit)

Excitation power supply: 12VDC ± 5%24VDC ± 5% 25mA

Indication > High setpointHigh setpoint >= Indication >= Lo setpoint

Indication < Lo setpoint

HIGOLO

Setting range : -9999 to 9999Hysteresis : 1 to 999 digit for each setpointsRelay contact capacity : AC250 V 2 A resistive load

DC30 V 2 A resistive loadPhotocoupler capacity : DC30 V 20 mA


HI & LO setpoints output (A6XXX-1X Reply output)(A6XXX-2X Photocoupler)

Comparative condition

pattern 1 pattern 2 pattern 3 pattern 4 pattern 5 pattern 6 pattern 7 pattern 8P.SEL1 OFF ON OFF ON OFF ON OFF ONP.SEL2 OFF OFF ON ON OFF OFF ON ONP.SEL3 OFF OFF OFF OFF ON ON ON ON

ON : Shorted between COM terminal and P.SEL terminal or same levelOFF : Open between COM terminal and P.SEL terminal or 5 V

Start/Hold : shorted between COM terminal or same level holdOpen COM terminal and start/hold terminal or 5 V start

D.ZERO : Shorted between COM terminal and D.ZERO terminal ONP.HOLD : Shorted between COM terminal and P.HOLD terminal ONR.RE(relay reset) : Shorted between COM terminal and R.RE terminal ONP.SEL1 to 3 : as below

External control (A6XXX-X1)

Option

BCD output (A6XXX-X2 TTL)(A6XXX-X3 Open collector)

Type of output: Open collector or TTLLogic: ChangeableOutput rate: DC30V 10mA(open collector)

Funout 2(TTL)

Analog output (A6XXX-X4)

more than 10kΩ

less than 550Ω

±(0.5% of F.S)50mV p-p

25mV p-p

0 to 1V0 to 10V1 to 5V

4 to 20mA

Output Load resistance Accuracy Ripple

Output method : PWM methodScaling : Digital scalingResolution : 13 bitReponse time : approx 0.5sec

RS232C (Conforming to EIA RS-232C)(A6XXX-X5)Communication method : Full duplexTransmission speed : 4800/9600/19200/38400 bpsStart bit : 1 bitData length : 7 bit/8 bitParity : Even parity/ odd parity/ noneStop bit : 1 bit/2 bitCharacter code : ASCII codeTransmission control process : Ignord process

RS-485 (conforming to EIA RS-485)(A6XXX-X6)Communication method : Full duplexTransmission speed : 4800/9600/19200/38400 bpsStart bit : 1 bitData length : 7 bit/ 8 bitParity : Even parity/ odd marity/ noneError detection : BCCStop bit : 1 bit/2 bitCharacter code : ASCII codeTransmssion control process : Ignord processSignal name : +non reversal output

- reversal outputMaximum no of meter connected : 31Line length : up to 500m in total


A60

00A6000 SERIES DIGITAL PANEL METER

A6000 Ordering CodeA6 -

Option 0. none1. External control2. BCD output (TTL)3. BCD output (open collector)4. Analog output5. RS-232C6. RS-4857. RS-232C, analog output8. RS-485, analog output

Comparator output 0. none1. Relay2. Photocoupler

Input 1. DC voltage2. DC current3. DC current4. AC voltage5. AC current6. AC current7. Resistance8. Temperature (T/C, RTD)9. FrequencyA. Strain gaugeB. Process

Display board 1. Multiple2. Single

Power supply 1. AC 100 to 240 V2. DC12 to 48 V

Dimensions

Multiple

Input Option

Comparator Power

Single

48

(97.

5)

10.9

77

0.5

(86.

5)

(21.

5)

44.8

91.5

102.5

96

45+

0.6

-0

92 +0.8- 0

MIN

.70

MIN.120

67

MEMO

68

MEMO


Transmitter

69

TERMINAL TYPE TRANSMITTERTZ-1X

Output signalDC 0 to 5VDC 1 to 5VDC 0 to 10VDC –10 to 10VDC 4 to 20mA

Output load resistance

more than 2kΩ

more than 4kΩ

less than 550Ω

Code No.0123AY special

Special Voltage output: DC -10 to 10V span 0.06 to 20V Current output: DC 0 to 20mA span 1 to 20mA

Output specifications

Ordering CodeInput signal

DC 0 to 5VDC 1 to 5VDC 0 to 10VDC –10 to 10VDC 0 to 1VDC 0 to 0.1VDC 0 to 0.06VDC 0 to 20VDC –2 to 2VDC –5 to 5VDC 4 to 20mADC 0 to 20mA

Allowable input

-50 to +150%F.S

Input Resistance

more than 1MΩ

250Ω

Code No.0123456789ABY special

Special Voltage input: DC -250V to 250V span 0.06 to 500VCurrent input: DC 0 to 50mA span DC 1mA to 50mA

Input specifications

TZ -1X-

Output

Input

0. DC 0 to 5V1. DC 1 to 5V2. DC 0 to 10V3. DC -10 to 10VA. DC 4 to 20mAY. special

Response time L. 50msecH. 1msec

0. DC 0 to 5V1. DC 1 to 5V2. DC 0 to 10V3. -10 to 10V4. DC 0 to 1V5. DC 0 to 0.1V6. DC 0 to 0.06V7. DC 0 to 20V8. DC -2 to 2V9. DC -5 to 5VA. DC 4 to 20mAB. DC 0 to 20mAY. special

Features

・ AC power supply 100 to 240VAC

・ DIN rail mounting

・ Input/Output/Power supply isolated

12

34

56

78

Load

Caution: Be polarity careful

PowerSupply(AC)

Inpu

t Sig

nal

Connection Diagram

ZERO SPAN

3(+)

4(–)

2

1

NC

Input SignalInput

Circuit

Isolation AMP

OutputCircuit

Powe

r Sup

ply Ci

rcuit

5(+)

6(-)

Output Signal

AC 100V

Block Diagram

Dimensions

Front

Side

98.1

25

94

35.2

37.3

40.8

9847

Terminal Cover

Slide Bar

1

2

3

4

5

6

7

8

General specificationsAccuracy: ±0.1% F.S (25˚C±2˚C)Fluctuating power source: ±0.06% F.SFluctuating load: ±0.06% F.STemp. Coefficient: ±0.02% F.S/˚CResponse time: 50msec or 1msec(TYP) (0 to 90%)Adustable volume range: ±5% F.S or more (zero and span)Insulated Resistance: input/output/power supply, more than 100MΩDielectric strength: input/output/power supply, AC2000V/1 min.Power supply: 100 to 240VAC±10%Power consuption: less than 30mA (at 100VAC)Operating Temp: -5 to 50˚C

Less than 90% RHCase Material: Black ABSWeight: Approx. 100g

NEW!


Tran

smitt

erTERMINAL TYPE TRANSMITTER

TZ-1B



more than 2kΩ

more than 4kΩ

less than 550Ω

Code No.0123AY Special

Special Voltage output: DC -10 to 10V span 0.06 to 20VCurrent output: DC 0 to 20mA span 1 to 20mA


Ordering CodePotentiometer100 to 10kΩ

special

Input range

0 to 100%

Code No.1Y

Special 100 to 10kΩ (span range 50% or more)Dip switch for only available input code 1SW1 ON: 0 to 100% (span adjust range 95 to 105%) SW2 ON: 0 to 90% (span adjust range 85 to 95%) SW3 ON: 0 to 80% (span adjust range 75 to 85%) SW4 ON: 0 to 70% (span adjust range 65 to 75%)


TZ -1B-

Output

Input


1. 0 to 100%Y. special

Features




12

34

56

78

MAX

MIN

Pot

entio

met

er

Load

Out

put S

igna

l


PowerSupply(AC)

Connection Diagram

ZERO

5(+)

6(-)2

1

4

3

SPANBase Circuit

InputCircuit

Isolation AMP

OutputCircuit

Powe

r Sup

ply Ci

rcuit

Output Signal

Pot

entio

met

er

AC 100V

Block Diagram

Dimensions

Front

Side

98.1

25

94

35.2

37.3

40.8

9847

Terminal Cover

Slide Bar

1

2

3

4

5

6

7

8

General specificationsAccuracy: ±0.1% F.S (25˚C±2˚C)Fluctuating power source: ±0.06% F.SFluctuating load: ±0.06% F.STemp. Coefficient: ±0.02% F.S/˚CResponse time: 50msec(TYP) (0 to 90%)Change setting error: less than ±2% (0 to 100% at deliver)Adustable volume range: ±5% F.S or more (zero and span)Insulated Resistance: input/output/power supply, more than 100MΩDielectric strength: input/output/power supply, AC2000V/1 min.Power supply: 100 to 240VAC±10%Power consuption: less than 30mA (at 100VAC)Operating Temp: -5 to 50˚C


NEW!


Transmitter

71

TERMINAL TYPE TRANSMITTERTZ-1D



more than 2kΩ

more than 4kΩ

less than 550Ω




Ordering CodeInput signalAC 0 to 1AAC 0 to 5A

Allowable inputInput Resistance

less than 0.05Ω

Code No.12Y special

less than 7.5A(15A, within 1ms)

Special Less than AC 0 to 5A span 1 to 5AInput Frequency 40hz to 1kHz


TZ -1D-

Output

Input


1. AC 0 to 1A2. AC 0 to 5AY. special

Features




12

34

56

78

Inpu

t Sig

nal

Load

Out

put S

igna

l


PowerSupply(AC)

Connection Diagram

ZERO

1

2

3

6

NC

CT

SPAN

Input Signal OutputCircuit

Powe

r Sup

ply Ci

rcuit

5(+)

6(-)

Output Signal

AC 100V

T-RMSset-up

diagram

Block Diagram

Dimensions

Front

Side

98.1

25

94

35.2

37.3

40.8

9847

Terminal Cover

Slide Bar

1

2

3

4

5

6

7

8

General specificationsAccuracy: ±0.15% F.S (5 to 100% F.S)

±0.5% F.S (0 to 5% F.S)25˚C±2˚C

Fluctuating power source: ±0.06% F.SFluctuating load: ±0.06% F.SFluctuating frequency: ±0.2% F.S(60Hz)Temp. Coefficient: ±0.02% F.S/˚CResponse time: Less than 700msec (TYP) (0 to 90%)Adustable volume range: ±5% F.S or more (zero and span)Insulated Resistance: input/output/power supply, more than 100MΩDielectric strength: input/output/power supply, AC2000V/1 min.Power supply: 100 to 240VAC±10%Power consuption: Less than 30mA (at 100VAC)Operating Temp: -5 to 50˚C


NEW!


Tran

smitt


TZ-1E



more than 2kΩ

more than 4kΩ

less than 550Ω


Special Voltage output: DC -10 to 10V span 1 to 20V Current output: DC 0 to 20mA span 1 to 20mA



AC 0 to 35VAC 0 to 100VAC 0 to 110VAC 0 to 200VAC 0 to 220V


more than 1MΩ

Code No.12345Y special

less than 150%(Max. AC250V)

Special Voltage input: AC 0 to 250V span 4 to 250VInput Frequency : 40Hz to 1KHz


TZ -1E-

Output

Input


1. AC 0 to 35V2. AC 0 to 100V3. AC 0 to 110V4. AC 0 to 200V5. AC 0 to 220VY. special

Features




12

34

56

78

Load

Out

put S

igna

l


PowerSupply(AC)

Inpu

t Sig

nal

Connection Diagram

ZERO

1

2

3(+)

4(-)

NC

SPAN

Input SignalOutputCircuit

Powe

r Sup

ply Ci

rcuit

5(+)

6(-)

Output Signal

AC 100V

T-RMSset-up

diagram

Isolation AMP

Block Diagram

Dimensions

Front

Side

98.1

25

94

35.2

37.3

40.8

9847

Terminal Cover

Slide Bar

1

2

3

4

5

6

7

8

General specificationsAccuracy: ±0.15% F.S (5 to 100% F.S)

±0.5% F.S (0 to 5% F.S)25˚C±5˚C

Fluctuating power source: ±0.06% F.SFluctuating load: ±0.06% F.SFluctuating frequency: ±0.2% F.S (60Hz)Temp. Coefficient: ±0.02% F.S/˚CResponse time: less than 700msec(TYP) (0 to 90%)Adustable volume range: ±5% F.S or more (zero and span)Insulated Resistance: input/output/power supply, more than 100MΩDielectric strength: input/output/power supply, AC2000V/1 min.Power supply: 100 to 240VAC±10%Power consuption: less than 30mA (at 100VAC)Operating Temp: -5 to 50˚C


NEW!


Transmitter

73

TERMINAL TYPE TRANSMITTERTZ-1F



more than 2kΩ

more than 4kΩ

less than 550Ω





DC 0 to 5mVDC 1 to 10mVDC 0 to 50mVDC 0 to 60mVDC 0 to 100mVDC 0 to 10µADC 0 to 100µADC 0 to 200µA


more than 1MΩ

more than 1KΩ

less than 500Ω

Code No.01234ABCY special

-50 to +150%F.S

Special Voltage input: DC -100mV to 100mV span DC 5 to 200mVCurrent input: DC -5mA to 5mA span DC 10µA to 10mA


TZ -1F-

Output

Input


Response time L. 50msecH. 3msec

0. DC 0 to 5mV1. DC 0 to 10mV2. DC 0 to 50mV3. DC 0 to 60mV4. DC 0 to 100mVA. DC 0 to 10µAB. DC 0 to 100µAC. DC 0 to 200µAY. special

Features




12

34

56

78

Load


PowerSupply(AC)

Inpu

t Sig

nal

Connection Diagram

ZERO SPAN

3(+)

4(–)

2

1

NC

Input SignalInput

Circuit

Isolation AMP

OutputCircuit

Powe

r Sup

ply Ci

rcuit

5(+)

6(-)

Output Signal

AC 100V

Block Diagram

Dimensions

Front

Side

98.1

25

94

35.2

37.3

40.8

9847

Terminal Cover

Slide Bar

1

2

3

4

5

6

7

8

General specificationsAccuracy: ±0.1% F.S (25˚C±2˚C)Fluctuating power source: ±0.06% F.SFluctuating load: ±0.06% F.STemp. Coefficient: ±0.02% F.S/˚CResponse time: 50msec or 3msec(TYP) (0 to 90%)Adustable volume range: ±5% F.S or more (zero and span)Insulated Resistance: input/output/power supply, more than 100MΩDielectric strength: input/output/power supply, AC2000V/1 min.Power supply: 100 to 240VAC±10%Power consuption: less than 30mA (at 100VAC)Operating Temp: -5 to 50˚C


NEW!


Tran

smitt

erPROGRAMMABLE TRANSMITTER

TW-3M

0 to 5 VDC1 to 5 VDC0 to 10 VDC4 to 20 mADC0 to 20 mADC

More than 2 kΩMore than 2 kΩMore than 4 kΩLess than 550 ΩLess than 550 Ω

Output signal Allowable load resistance


Ordering Code

0 to 5 VDC1 to 5 VDC0 to 10 VDC0 to 60 mVDC4 to 20 mADC0 to 20 mADC

More than 1 MΩ

250 Ω

Input signal Input resistance

Input Specification

TW-3M - -

1: 100 - 240VAC4: 24VDC (CE available)

C: Connector (screw) Type (UL available)N: Screw Type

Features

・ Can change input and output by front Dip switch

・ 100 to 240 VAC or 24 VDC power supply

・ DIN rail mount type

6

5

4

3

2

1

12

11

10

9

8

7

Inputsignal

Power(AC)

Outputsignal

Power(DC)

Note: When conducting wiring, be careful with its polarity.

Connection Diagram

Input signalOutput signal

ZERO SPAN

Power

75

68

11

12

Isolated Amp.

Power circuit

Output

circuit

Input

circuit

Block Diagram

General SpecificationsLinearity: Less than ± 0.1% F.STemperature characteristic: ± 0.02% F.S/°CResponse time: Less than 50ms ( 0 to 90%)Insulantion resistance: Between input and output or power supply,

more than 100MΩDielectric strength: Between input and output or power supply,

for 1 min. at 2000VACPower supply: 24VDC ±10%

100-240VAC ±10%Power comsumption: Less than 80mA (at 24VDC)

Less than 50mA (at 100-240VAC)Operationg temperature: -5 to 50°COperating humidity: Less than 90%

(No dew-condensing)Case material: Black PBT 94-V0Weight: Approx. 130g

Dimensions

ON

OF

F

1 2

3 4

SW

1

ON

OF

F SPA

N

ZER

O1 2

3 4

5 6

7 8

SW

2

Front view

Side view

35.4

35.2 4.5

1841

64.5

Sliding from 96 to 98

94

2048

I/Ora

nge

setti

ng D

ipS

Ws.

ZE

RO

/SPA

Nad

just

ers

Setting or changing input/output range

1. Setting or changing input rangeSW1

0-5V ONOFF

SW2

1-5V ONOFF

0-10V ONOFF

0-60mV ONOFF

4-20mA ONOFF

0-20mA ONOFF

1 2 3 4 1 2 3 4 5 6 7 8

2. Setting or changing output rangeSW1

0-5V ONOFF

SW2

1-5V ONOFF

0-10V ONOFF

4-20mA ONOFF

0-20mA ONOFF

1 2 3 4 1 2 3 4 5 6 7 8

(C Type) (N Type)


Transmitter

75

TRANSMITTER WITH ONE INPUT AND TWO OUTPUTSTW-2X

Other than the above

Code No.AY

Output signal4-20mA DC

Load resistanceLess than 550 ohm

Limit of Y specificationsCurrent output : 20mADC or less , Minimum span ; 1mADCVoltage output : From -10VDC to +10VDC

Minimum span ; 1VDC


Code No.012ABY

Output signal0-5V DC1-5V DC

0-10V DC4-20mA DC0-20mA DC

Load resistance

Less than 2K ohm

Less than 4K ohm

Less than 550 ohm

Limit of Y specificationsCurrent output : 20mADC or less , Minimum span ; 1mADCVoltage output : From -10VDC to +10VDC

Minimum span ; 1VDC

First output specifications

Second output specifications

Ordering Code


Code No.012ABY

Intput signal0-5V DC1-5V DC

0-10V DC4-20mA DC0-20mA DC

Input resistance

More than 1M ohm

250 ohm

Limit of Y specificationsVoltage input : 250VDC or less , Minimum span ; 100mVDCCurrent input : 50mADC or less , Minimum span ; 1mADC


TW-2X -

Second Output code

First Output code

Input code

0: 0 - 5V DC1: 1 - 5V DC2: 0 - 10V DCA: 4 - 20mA DCB: 0 - 20mA DCY: SpecialA: 4 - 20mA DCY: Special0: 0 - 5V DC1: 1 - 5V DC2: 0 - 10V DCA: 4 - 20mA DCB: 0 - 20mA DCY: Special

- 4 -C: Connector (screw) TypeN: Screw Type

Features

・ DIN rail mount

・ 2 outputs

・ Input/output1/output2/power supply Isolated

Note: Pay attention to the connection polarity.

Signalinput

Signaloutput1

DC24V

Signaloutput2

TW-2X

654321

121110987

-

+

-

+

-

+

-

+

Connection Diagram

Inputcircuit

Outputcircuit

Isoration Amp.

Powe

r circ

uit

Isolation Amp.

1

Outputcircuit

2

ZEROSPAN

TW-2X

ZEROSPAN

Signaloutput 2

DC 24V

NC

Signaloutput 1

Signalinput

5(+)

1(+)

6(–)

2(–)

11(+)

7(+)

12(–)

9

10NC

3

4

8(–)

Block Diagram

Dimensions

Front view

Side view

Withterminalcover

64.5

94

96～98

35.4

2017

.4

42.5

4.3

4841

ZE

RO

OU

T 1

SPA

N

OU

T 1

ZE

RO

OU

T 2

SPA

N

OU

T 2

General specificationsAccuracy: ±0.25% FSTemperature characteristic: ±200 ppm FS/ (TYP)Response time: Less than 50msec ( 0 to 90%)Insulantion resistance: Between input and/output 1/output 2/power ;

More than 100MΩ (at 500VDC)Dielectric strength: Between input and/output 1/output 2/power ;

For 1 min. at 2000VACPower supply voltage: 24VDC ±10%Current comsumption: Less than 110mAOperationg ambient temperature: -5 to 50Operating ambient humidity: Less than 90% RH (No condensing)Weight: Approx. 130gAccessories: Instruction manual

Terminal coverDetachable 6-P connector

(C Type) (N Type)


Tran

smitt

er


Output Specifications (1st, 2nd output)

General SpecificationAccuracy: ±0.25% F.S (25˚C±2˚C)Temperature Characteristic: ±0.02% F.S/˚CResponse time: less than 50msec (0 to 90%)Insulation resistance: Between input and output 1, output 2, power

supply more than 100M Ω (500V DC)Dielectric strength: Between input and output 1, output 2, power

supply 1500V AC per 1 min.Power supply: 100 to 240V AC ±10%Operating temperature: –5 to 50˚C less than 90%RH (No

condensing)Power comsumption: Less than 45mA at 100V AC

Less than 30mA at 200V ACWeight: Approx. 130gAccessory: Instruction manual, terminal cover

Transmitter With Two OutputsTW-2XA

Featuers• DIN Rail m ount

• AC Power Supply 100 to 240V AC±10%

• 2 Outputs

Y specificationInput voltage: less than 250V DC min span 0.1V DCInput Curent: less than 50mA DC min. span 1mA DC

Special250 Ω

Input0 to 5V DC1 to 5V DC0 to 10V DC4 to 20mA DC

Input Resistance

more than 1M Ω

Code No.012AY

Special

Output signal0 to 5V DC1 to 5V DC0 to 10V DC4 to 20mA DC

Load Resistance

more than 2K Ω

more than 4K Ωless than 550 Ω

Code No.012AY

Y specificationOutput voltage: less than ±10V DC min. span 1V DCOutput Curent: less than 20mA DC min. span 1mA DC

Ordering Code

Dimensions

Connection Diagram

Block Diagram

TW-2XA- -1

Input

2nd output

1st output

0. 0 to 5V DC 1. 1 to 5V DC 2. 0 to 10V DC A. 4 to 20mA DC Y. Special



Front

96 to 98 Slide

94

64.5

20

35.4

17.4

41

4.3

48

Side

Output 1

Input

TW–2XA–XXX–1

Output 2

Power Supply(AC)

ZERO SPAN ZERO SPAN

Output 1 OutputCircuit 1

InputCircuit

InputCircuit

OutputCircuit 2

Input

Output 2

Power Supply


Transmitter

77

InputSpecification


[1st output]

Y specification

[2nd output]

General SpecificationAccuracy: ±0.25% F.STemperature characteristic: ±200ppmF.S/˚C(TYP)Response time: less than 2 sec (0 to 90%)Insulation resistance: Between Input and output/power supply

more than 100M Ω (500V DC)Dielectric strength: Between Input and output/power supply

1500V AC per 1 min.Power supply: 100 to 240V AC ±10%

24V DC ±10%Power consumption: Less than 110mA at DC

Less than 50mA at ACOperating temperature: –5 to 50˚C less than 90%RH (No

condensing)Weight: Approx. 160gAccessory: Instruction manual, terminal cover, 6P

connector

Temperature Transmitter With Two OutputsTW-2C

Featuers• DIN Rail Mount

• AC Power Supply 100 to 240V AC ±10%

DC Power Supply 24V DC ±10%

• 2 Outputs

• Sensor Type: R,K,E,J,T,S,B,PT-100 Ω

SensorRKEJTSB

Pt 100 Ω

CodeRKEJTSBP

Input temperature0 to 1700˚C

–50 to 1200˚C–50 to 900˚C–50 to 1000˚C–50 to 350˚C0 to 1700˚C

200 to 1700˚C–150 to 800˚C

Minimum Span400˚C100˚C100˚C100˚C100˚C500˚C

1000˚C100˚C

Thermocouple Input SpecificationAccuracy of Cold Junction Compensation ±1˚C (10 to 30˚C)(For thermocouples other than B type thermocouple)

RTD lnput SpecificationAllowable leadwire resistance: Less than 10ΩCurrent following through RTD: 1mA

Ordering Code

Dimensions

Connection Diagram

Block Diagram

RKEJTSBP

0. 0 to 5V DC1. 1 to 5V DC2. 0 to 10V DCA. 4 to 20mA DC

A. 4 to 20mA DCY. special

1. 100 to 240 AC4. 24V DC

TW-2C- -

Input

2nd output

Power supply

1st output

35.4

41

20

94

96 to 98 Slide

64.5

17.4

42.4

4.3

Front

Side

TerminalCover

TW–2C

TCRTD

Input

PowerSupply

1st Output

2nd Output

Input MPU

(–)6

(–)5

(+)4

11

12

9(+)

7(+)

8(–)

Burnout Circuit

Cold Junction Compensation

10(–)

2ndOutputCircuit

1stOutputCircuit

Pow

er Supply

CodeAY

Output signal4 to 20mA DC

Output Load resistanceless than 550 Ω

Output at burnout

Approx. 120% F.SSpecial

Code Y

Output signal 0 to 5VDC 1 to 5VDC 0 to 10VDC

Output Load resistance

more than 2K Ω

more than 4K Ω

Output at burnout

Approx. 120% F.S

Code012A

Output signal0 to 5V DC1 to 5V DC0 to 10V DC4 to 20mA DC

Output Load resistance

more than 2K Ω

more than 4K Ωless than 550 Ω

Output at burnout

Approx. 120% F.S


Tran

smitt

er

DC voltage measurement

DC current measurement

Specification

Measuring SectionInput configuration : Single ended Conversion rate : 12.5times/sec (50Hz), 15times/sec (60Hz)Noise rejection ratio : NMR40dB or more (50/60Hz)Display : Red LED 8mm heightPolarity display : Automatic “-” display when the computation

result is minusOverrange warning : When input exceeds the maximum display,

display “o.L” or “-o.L”Maximum display : ± 9999 (4 digit)Decimal point : Settable to any digit positionZero display : Leading zero suppressionTemp. coeff. : ± 100ppm/˚C

Common SectionMemory backup : EEPROM (rewrite 100,000times)Operating temp. : 0 to 50˚C 35 to 85%RHStorage temp. : -10 to +70˚C less than 60%RHPower supply : 24V DC ± 20%Power consumption : 70mA (TYP) at 24V DCDimensions : 48mm (W) 98mm (H) 41mm (D)Weight : approx. 140g (unit only)Dielectric strength : Input (LO) and comparator output 500V DC

per min.Power supply (0V) and input (LO),comparator output case, 1500V AC per min.Input (LO) and case, 1500V AC per min.

Case material : Black PBTInsulation resistance : 500V DC 500M ohm or more as the above

terminalsExcitation supply : 24V DC ± 10% 25mA ripple less than

200mVp-pAccessories : Instruction manual. terminal cover,

connector

Comparison SectionControl method: Computation by microcomputerSetting range: -9999 to +9999Operating: By conversion rateComparison condition: Hi setpoint < Measured value →HI

Hi setpoint Measured value Lo setpoint →GOMeasured value < Lo setpoint →LO

Relay output capacity: 30V DC/1A resistive load125V AC/0.5A resistive load

Photo coupler output capacity: Voltage max. 30VCurrent max. 50mASaturation voltage less than 1.2V at 50mA

Digital Alarm SetterTW-3R

Featuers• DIN rail mount

• Hi and Lo setpoints

• Power supply 24V DC

Range Measurment012

0 to 5V1 to 5V0 to 9.999V

DisplayOffset ± 9999

Fullscale± 9999

Input Protection

± 250V

Input impedance1M Ω1M Ω1M Ω

Accuracy: ± (0.1% of rdg +2 digit) (23˚C ± 5˚C 35 to 85%RH)

Range Measurment

A 4 to 20mA

DisplayOffset ± 9999

Fullscale± 9999

Input Protection

± 60mA

Input impedance

50 Ω

Accuracy: ± (0.1% of rdg +2 digit) (23˚C ± 5˚C 35 to 85%RH)

Ordering Code

Dimensions

Connection Diagram

TW-3R-

Comparator output

Range

1. Relay 2. Photo Coupler

0. 0 to 5V DC 1. 1 to 5V DC 2. 0 to 9.999V DC A. 4 to 20mA DC

35.4

41

20

94

96～98 Slide

64.5

17.4

42.4

4.3

Front

Side

Terminal Cover

HI

GO

LO

EM

NCHI

LOInput

－

＋

DC24V

TW–3R

Relay

0V

Photocoupler

NCNC

+24V

HI

COM

LOCC

e


Transmitter

79

TransmitterTH-1X

Code No. Output signal Load resistancemore than 2KΩmore than 2KΩmore than 4KΩmore than 4KΩless than 550Ω

0123AY

DC 0 to 5 VDC 1 to 5 VDC 0 to 10 V

DC -10 to 10 VDC 4 to 20 mA

special

Special: Voltage input less than ±10 V DC, min span 1 VDCCurrent input less than 20 mA DC, min span 5 mA DC

Output specificationDC voltage & current

Ordering Code

Code No. Input signal Input resistance012345AY

DC 0 to 5 VDC 1 to 5 VDC 0 to 10 V

DC -10 to 10 VDC 0 to 1 V

DC 0 to 0.1 VDC 4 to 20 mA

special

more than 1MΩ

250Ω

Special: Voltage input less than 250 V DC, min span 0.1 VCurrent input less than 50 mA DC, min span 5 mA DC

Input specificationsDC voltage & current

TH-1X-

Input code

Output code

0.　DC 0 to 5 V1.　DC 1 to 5 V2.　DC 0 to 10 V3.　DC -10 to 10 V4.　DC 0 to 1 V5.　DC 0 to 0.1 VA.　DC 4 to 20 mAY.　special

0.　DC 0 to 5 V1.　DC 1 to 5 V2.　DC 0 to 10 V3.　DC -10 to 10 VA.　DC 4 to 20 mAY.　special

Features

・Easy to change input/output code (SJ)

・Slim width 12.5 mm

・DIN rail mount type

・24 VDC power supply

Dimensions

＋－

78

＋－

＋－

6

34

34

56

78

INPUT

SPAN

ZERO

TAG

TH-1X

MODEL

INPUT

OUTPUT

POWER

LOT No.

TAG No.

TH-IX-00

DCO～5V

DCO～5V

DC24V

0105A

OUTPUT

TOKYO JAPAN

ASAHI KEIKI

POWER

5

99±0.5

59±0.5

115±

0.5

（4）

4max

12.5

DIN rail

Front

Side

General specificationAccuracy: ±0.25% F.STemp. Coefficient: ±0.02% F.S/°CResponse Time: less than 20 msec (0 to 90%TYP)Insulated Resistance: input/output/power supply, more than 100MΩDielectric Strength: input/output/power supply, AC 1500V/1 min.Power Supply: 24 V DC±10%Power consumption: less than 60 mAOperating Temp.: -5 to 50°C less than 90%RHSize: 99 mm (H)×12.5 mm(W)×115 mm(D)

Connection Diagram

＋

－

＋

－

DC 24V

output

LOAD

input 4

3

6

5

8

7


Tran

smitt

erTemperature Transmitter

TH-1C

Code Output signal

0

1

2

A

DC 0 to 5 V

DC 1 to 5 V

DC 0 to 10 V

DC 4 to 20 mA

OutputLoad resistance

More than 2k Ω

More than 4k ΩLess than 550 Ω

Output at burnout

Approx 120% F.S


Ordering Code

Sensor Code Input temperature Minimum Span

R

K

E

J

T

S

B

Pt 100 Ω

R

K

E

J

T

S

B

P

0 to 1700°C-50 to 1200°C-50 to 900°C-50 to 1000°C-50 to 350°C0 to 1700°C

200 to 1700°C-150 to 800°C

400°C100°C100°C100°C100°C500°C1000°C100°C

Input Specification

TH-1C-

Input code 1.

2.

Output code

Accessory code

R. R Type (0 to 1700°C)K. K Type (0 to 1200°C)E. E Type (0 to 900°C)J. J Type (0 to 1000°C)T. T Type (0 to 350°C)S. S Type (0 to 1700°C)B. B Type (0 to 1700°C)

P. RTD Pt (0 to 800°C)

0. 0 to 5 VDC1. 1 to 5 VDC2. 0 to 10 VDCA. 4 to 20 mADC

0. No accessory provided1. Software and cable provided

As input specifications, separately specify the zero and span temperatures (in steps of 1°C).Otherwise, any one of the above temperatures is selected.When purchasing only the setting soft cable, specify "TH-1C-XX-1."

Example: TH-1C-K0-1 0 to 1000°C

Can change input sensor

Featuers

・Slim width 12.5mm


・Power supply 24VDC ±10%

・Input sensor

R,K,E,J,T,S,B, PT-100 ohm

Dimensions

990.5

590.5

115

0.5

(4)

4

12.5

0.5

0

DIN rail (35mm Wlde)

Front View

Side View

General SpecificationAccuracy: ±0.25% F.S (At 25±2°C)Temperature characteristic: ±0.02% F.S/°CPower supply voltage variation:±0.1% F.SResponse Time: Less than 2 sec (0 to 90%)Insulation resistance: Between input and output/power supply;

More than 100 MΩ at 500 VDCDielectric strength: Between input and output/power supply;

For 1 min. at 1500 VACPower supply voltage: 24V DC±10%Consuming current: Less than 60 mA (At 24 VDC)Operating ambient temperature: -5 to 50°COperating ambient humidity: Less than 90%RH (No-condensing)Storage temperature: -10 to 70°CStorage humidity: Less than 60%RH (No-condensing)Case material: Black PC risin 94V-2Weight: Approx. 80g

Connection Diagram


2

1

4

3

6

5

8

7

2

1

4

3

6

5

8

7

Out

put s

igna

l

LoadDC

24V

Out

put s

igna

l

LoadDC

24V

T/C input

Pt input

B

A

B

Thermocouple Input SpecificationAccuracy of Cold Junction Compensation ±1°C (10 to 30°C)(For thermocouples other than B type thermocouple)

RTD Input SpecificationAllowable leadwire resistance: Less than 10 ΩCurrent following through RTD: 1mA


Transmitter

81

TransmitterTH-41

Ordering Code

TH-41-

Number of channels 1.　1 channel2.　2 channel

Featuers

・Self-powered

・1ch or 2ch input

・Slim width 12.5mm


Dimensions

34

12

56

78

TAG

TH

-41

990.5

590.5

115

0.5

(4)

4max

12.5

0.5

0

DIN rail (35mm Wlde)

Front View

Side View

12

INPU

T1

34

INPU

T2

56

OUTP

UT2

78

OUTP

UT1

MOD

ELIN

PUT1

OUTP

UT1

INPU

T2 OU

TPUT

2LO

T No

.TA

G No

.

TH-4

1-2

DC4

20

mA

max

. 30V

30m

ADC

4

20m

ADC

4

20m

Am

ax. 3

0V 3

0mA

DC4

20

mA

0105

A

TOKY

O JA

PAN

ASAH

I KEI

KI

SpecificationsInput signal: 4 to 20mADCMax. input current 30mADCMax. output load: 1000 ohmsVoltage loss: less than 3VResponse time: 20ms (0 to 90%)Temperature characteristic: less than ±0.005%/°CAccuracy: ±0.1% F.SOperating temp.: -5 to 50 °COperating ambient humidity: less than 90%RH (no condensing)Storage temp.: -10 to 70°CWeight: Approx. 80gDielectric Strength: Between the input and output 2000VAC/1min.Insulation resistance: Between the input and output or power supply

more than 100M ohms (at 500 VDC)

Connection Diagram

2

1

4

3

6

5

8

7


Inpu

t sig

nal C

H2

Inpu

t sig

nal C

H1

Out

put s

igna

l CH

1

Load

Load

Out

put s

igna

l CH

2

Operating ConditionWhen using the TH-41, pay attention to the following.The TH-41 can be used if the sum of voltage calculated by a voltageloss of 3V across the TH-41 and that of RA X 20mA across a loadconnected is smaller than the signal cource voltage.

Signalsource

LoadRA

TH-41VA

20 mA 20 mA

Voltage loss: 3V

VA 3V 20 mA RA


Tran

smitt

er

Input Specification


General SpecificationSetting range at factory: Input 1 to 5 V DC, Output 4 to 20mA DCAccuracy: ±0.25% F.S (25˚C±2˚C)After changed input range error:

±1% F.SAfter changed output range error:

±1% F.STemperature characteristic: ±0.02% F.S/˚CResponse time: less than 15ms (0 to 90%)(TYP)Insulation resistance: Between input and output/power supply

more than 100M ohm at 500V DCDielectric strength: Between input and output/power supply

1500V AC per 1min.Power supply: 24 V DC ±10%Power consumption: Less than 80mAOperating temperature: –5 to 50˚C Less than 90%RH (No

condensing)Weight: Approx. 80gApproval: EN61000-6-2, EN55011Accessory: Switch sheet

Ordering code

Programmable TransmitterTH-1M

Featuers• Can change input and output by front dip switch


• DIN Rail mount

Input resistance

More than 1 MΩ

250 Ω

Input signal0 to 5V DC1 to 5V DC0 to 10V DC0 to 60mV DC4 to 20mA DC0 to 20mA DC

Output signal0 to 5 V DC1 to 5 V DC0 to 10 V DC4 to 20 mA DC0 to 20 mA DC

Allowable load resistanceMore than 2 k ΩMore than 2 k ΩMore than 4 k ΩLess than 550 ΩLess than 550 Ω

Setting or changing input/output range

Dimensions

Connection Diagram

Block Diagram

ONOFF

1 2 3 4

SW1 SW2

0-5V

1. Setting or changing input range

1-5V

0-10V

0-60mV

4-20mA

0-20mA1 2 3 4 5 6 7 8

ONOFF

ONOFF

ONOFF

ONOFF

ONOFF

ONOFF

1 2 3 4

SW1 SW2

0-5V

2. Setting or changing output range

1-5V

0-10V

4-20mA

0-20mA1 2 3 4 5 6 7 8

ONOFF

ONOFF

ONOFF

ONOFF

99±0.5

43

65

87SP

AN

ZE

RO

TA

GT

H-1

M

4max

12.5

+0.

5

–

0

59±0.511

5±0.

5

(4)

DIN RAIL

Front

Side

DC24V

OutputInput

3(+)

4(–) 6(–)

5(+)

8(–)

7(+)

ZERO SPAN

OutputCircuit

InputCircuit

Pow

er Supply

Circuit

Input Output

Isolation AMP

DC24V

TH-1M


Transmitter

83

Ordering Code

Input specifications4-20mA DC (Input resistance 50Ω)


For code No. YLimit of specificationsVoltage output : Less than +10VDC and more than -10VDCMinimum span : 1VDCCurrent output : Less than 20mADCMinimum span : 5mADC

SpecificationsAccuracy : ±0.25%F.S (23˚C±2˚C) Temperature characteristic : ±200ppmF.S/˚C (TYP.)Response time : Less than 50 msec (0~90%)Insulated resistance : Between input and output/power supply;

More than 100MΩ (at 500V DC)Dielectric strength : Between input and output/power supply;

For 1 min. at 2000VACPower supply voltage : 24V DC±10% less than 80mAOperating ambient Temp. : -5 to +50˚COperating ambient humidity : Less than 90%RH(No-condersing)Weight : Approx. 80g

Powerr supply to 2-wire transmitterOutput voltage : 24~32VDC (No load resistance)Current Capacity : Less than 22mADCCurrent at short circuit : Less than 30mADCPermissible : Short circuit duration : No limit

Dimensions

Connection Diagram

Block Diagram

DISTRIBUTORTZ-5L

Features• DIN rail mount

• Low cost

• Miniature Size

• Isolated Input/Output/Power supply

Output code

Input code

0: DC 0~5V1: DC 1~5V2: DC 0~10VA: DC 4~20mAY: Special

DC 4~20mA

TZ-5L-A

Circuit

Power Supply Circuit

IsolationAMP

Output

DC24V

Output

5(＋)6(ー)

7(＋)

8(ー)

3(ー)

1(+)

4(–)

2(＋)

ExcitationPowerSupply

Zero Span

Input

InputCircuit

012AY

DC0~5VDC1~5VDC0~10VDC4~20mA


Output signal

more than 2KΩ

more than 4KΩless than 550Ω

Load resistanceCode No.

5 max94

54

63

11.5

25

25.5

Side

Front

83

34.5 41

2-W

ireT

rans

mitt

er

Out

put S

igna

l

DC24V6 842

5 731

LOA

D

Note : Pay attention to the connection polarity.


Tran

smitt

er


Output Specifications

General SpecificationsAccuracy: ±0.25% F.S.Temp. Coefficient: ±200 ppm/°C F.S(Typ)Response Time: Less than 50msec(0 to 90%)Insulated Resistance: Input/Output/Power supply more than

100MΩ(500VDC)Dielectric Strength: Input/Output/Power supply 2000VAC/l minPower Supply: 24VDC ±10% less than 60mAOperating Temp: -5~+50°C, less than 90%RHWeight: 80g

012ABY

DC0~5VDC1~5VDC0~10VDC4~20mADC0~20mA　　　　　　　　 Special

Output signal

more than 2KΩ

more than 4KΩ

less than 550Ω

Input resistanceCode No.

*Code "Y" specificationsVoltage output: less than ±10VDC (span 1VDC)Current output: less than 20mADC (span 1mADC)

012ABY

DC0~5VDC1~5VDC0~10VDC4~20mADC0~20mA　　　　　　　　 Special

Input signal

more than 1MΩ

250Ω

Input resistanceCode No.

*Code "Y" specificationsVoltage input: less than 250VDC (span 100mVDC)Current input: less than 50mADC (span 1mADC)

TERMINAL TYPE TRANSMITTERTZ-5H

Features• Miniature size

• DIN rail mount


• Easy connection

Side

Front

98

9454

63

11.5

25

2 4 6 8

5 71 3

83

25.5 34

.5 41

INPUTOUTPUTDC24V

6 842

5 731

LOA

D

Circuit


IsolationAMP

Output

DC24V

Output

5(＋)6(ー)

7(＋)

8(ー)

4(ー)

1

2

3(＋)

N.C

Zero Span

Input

InputCircuit

Block Diagram

Connection Diagram

Dimensions

TZ-5H-

Output code

Input code

0. 0~5VDC1. 1~5VDC2. 0~10VDCA. 4~20mADCB. 0~20mADCY. Special

0. 0~5VDC1. 1~5VDC2. 0~10VDCA. 4~20mADCB. 0~20mADCY. Special

Ordering Guide


Transmitter

85

TERMINAL TYPE TRANSMITTERTZ-5X

Features

• DC Power supply 24VDC

• DIN rail mounting

• Input / Output / Power supply isolated

Output SignalDC 0 to 5VDC 1 to 5VDC 0 to 10VDC –10 to 10VDC 0 to 4VDC 4 to 20mA


more than 2 kΩ

more than 4 kΩ

more than 2 kΩless than 550 Ω

Code No.01236AY Special

Special Voltage output: DC -10 to 10V span DC 1VCurrent output: DC 0 to 20mA span DC 1mA


Ordering CodeInput Signal

DC 0 to 5VDC 1 to 5VDC 0 to 10VDC –10 to 10VDC 0 to 1VDC 0 to 0.1VDC 0 to 4VDC 0 to 20VDC –2 to 2VDC –5 to 5VDC 4 to 20mADC 0 to 20mA

Allowable input

–50 to +150%F.S

Input Resistance

more than 1MΩ

250Ω

Code No.0123456789ABY Special

Special Voltage input: DC less than 250V span 0.1VCurrent input: DC less than 50mA span DC 1mA


0. DC 0 to 5V1. DC 1 to 5V2. DC 0 to 10V3. DC –10 to 10V6. DC 0 to 4VA. DC 4 to 20mAY. special

0. DC 0 to 5V1. DC 1 to 5V2. DC 0 to 10V3. DC –10 to 10V4. DC 0 to 1V5. DC 0 to 0.1V6. DC 0 to 4V7. DC 0 to 20V8. DC –2 to 2V9. DC –5 to 5VA. DC 4 to 20mAB. DC 0 to 20mAY. special

Output

Input

TZ-5X-

DC24V

++

–––

+12

34

56

78

Inpu

t Sig

nal

Load

Out

put S

igna

l


Connection Diagram

3(+)

4(–)

ZERO SPAN

2

1

8(–)

7(+)DC 24V

5(+)

6(–)

NC

Input Signal InputCircuit

Isolation AMP

OutputCircuit

Powe

r Sup

ply Ci

rcuit

Output Signal

Block Diagram

Dimensions

Front

Side

94

25

57.6

35.2

37.3

40.8

9847

1

2

3

4

5

6

7

8

Terminal Cover

Slide Bar

General specificationsAccuracy: ±0.1% F.S (25˚C±2˚C)Temp. Coefficient: ±200PPM F.S/˚C (TYP)Response time: less than 50msec (0 to 90%)Insulated Resistance: input/output/power supply, more than 100MΩDielectric strength: input/output/power supply, AC2000V/1 min.Power supply: 240VDC±10%Power consuption: less than 65mA (at 24VDC)Operating Temp: -5 to 50˚C



Tran

smitt


Ordering Code

TZ-41

Dimensions

Connection Diagram

Block Diagram

SpecificationsSignal Input: 0 to 20mA,4 to 20mA or0 to 5mASignal Output: 0 to 20mA, 4 to 20mA or 0 to 5mAInput Current: Max. 30mALoad: Max. 600ΩVoltage loss between input and output: Approx. 3.3VOutput Ripple: Less than 0.5% (20mA at 250W)Temp, Coefficient: Less than ±100PPM/°CAccuracy: ±0.1% (23°C±1°C) at 250W loadAdditional Error: +0.1%/100W at load,250W

-0.1%/100W at load.250WOperating Temp: -5 to +50°C, less than 90% RHMechanical Design: Type of snap mount on DIN railInsulated Resistance: More than 100MW at 500VDC between input

and outputDielectric Strength: 1 min. at 2kVAC between input and outputWeight: Approx. 80g

INPUT/OUTPUTTZ-41 is designed as "Self Powered Isolation" and transformation ratio is1:1. Input current is 0 to 20mA, but customers can use input currentranges 0 to 5mA, 0 to 20mA or 4 to 20mA.Having 1:1 isolation the output current will of course be the same as theinput current, e.g., 0 to 5mA, 0 to 20mA, 4 to 20mA.TZ-41 will provide 0 to 5V or 1 to 5V output.

Output load and AccuracyPlease note the TZ-41 can operate into a load of up to 600W. Accuracyis a function of load resistance. Standard accuracy is +/- 0.1% with a250W load and ambient temp. of 23±1°C. For loads other then 250Waccuracy changes as shown below.

Example load 450ΩStandard accuracy: ±0.1%Additional error (+200W): ±0.1% - 0.2%=-0.1% to -0.3%

(-0.1%/100Ωatload>250Ω)

TZ-41

1

2

3（＋）

4（－）

N.C

N.C

N.C

N.C

５（＋）

６（－）

７

８

Output Output

Chopper Oscillation Circuit

RectifierCircuit

Features

• Miniature Size

• Self-powered

• Easy Connection

• DIN rail mount

11.5

25

63

54

94

98

83

1 3

2 4

5 7

6 8

25.5

34.5 41

Front

Side

1234

5678

Input Output

LOA

D

DC0~20mA(4~20mA)


Transmitter

87

General SpecificationsAccuracy: ±0.25% F.STemp. Coefficient: ±200ppm/˚C (Typ.)Response Time: Less than 80mS (0~90%) (Typ.)Dielectric Strength: Input/Output/Power supply AC2000V/1 min.Insulated Resistance: Input/Output/Power supply more than

100MΩ at DC500VOperating Temp.: -5~50˚CPower Supply: DC24V±10% less than 55mABurn Out: Upper side

TERMINAL TYPE TRANSMITTERTZ-5A

Ordering Code

Features

•Isolated Input/Output/Power supply

•DIN rail mount

•Input RTD sensor

TZ-5A-

Output Code

Input Code

1. 0~100°C2. 0~200°C3. 0~300°C4. 0~400°C5. 0~500°C6. 0~600°CY. Special

1. DC 1~5V2. DC 4~20mA3. DC 0~10VY. Special

Input SpecificationsPT-100 Ω three wires less than 20Ω

123456

Y

0 to 100°C0 to 200°C0 to 300°C0 to 400°C0 to 500°C0 to 600°CSpecial (0~600°C)(Span more than 100°C)

Temp. RangeCode No.

123

Y

1~5V4~20mA0~10VSpecial (Current 20mA)(Voltage less than ±10V)

Temp. RangeCode No.

Allowable Load: More than 2KΩ(At 1 to 5V)Resistance More than 4KΩ(At 0 to 10V)

Less than 550Ω(At 4 to 20mA)

Output SpecificationsDC voltage or current

Dimension

Connection Diagram

Block Diagram

98

9454

2541

2 4 6 8

5 71 3

Input

Pt100Ω

Output1 3 5

2 4 6

7

8

A

B BLO

ADDC

24V

Circuit

Power CircuitBurn-out Circuit

Input Circuit

IsolatedAmplifier

Constant Current Circuit

Output

DC24V

Output

＋5ー6

＋7

ー8

RTD

3

2

1

4

N.C

Span Zero


Tran

smitt

er

Input SpecificationsPotentiometer (100 to 10KΩ)


General SpecificationsAccuracy: ±0.25%F.ScTemp. Coefficient: ±200ppm/˚C (Typ.)Response Time: Less than 50mS (0~90%) (Typ.)Dielectric Strength: Input/Output/Power supply AC2000V/1 min.Insulated Resistance: Input/Output/Power supply more than

100MΩ at DC500VOperating Temp.: -5~50˚CPower Supply: DC24V +15%,-5% less than 55mAZero Adjustment Range: 0~10%Span Adjustment Range: 90~100%Reference Voltage: 0.5V

TERMINAL TYPE TRANSMITTERTZ-5B

Ordering Guide

Features

•Isolated Input/Output/Power Supply

•DIN Rail mount

•Input Potentiometer

TZ-5B-

Output Code

DC 1 to 5VDC 4 to 20mADC 0 to 10VY. Special

123Y

1~5V4~20mA0~10VSpecial

Temp.RangeCode No.

Special Current Output Range: Less than 20mA (Min. span 1mA)Special Voltage Output Range: Less than ±10V (Min. span 1V)

Allowable Load: More than 2KΩ(At 1 to 5V)Resistance More than 4KΩ (At 0 to 10V)

Less than 550Ω (At 4 to 20mA)

Dimension

98

9454

2541

2 4 6 8

5 71 3

Connection Diagram

Block Diagram

Input

Potentionmeter

Output1 3 5

2 4 6

7

8

A

B

LOA

DDC24V

Power CircuitInput Circuit

IsolatedAmplifier

Constant Voltage Circuit

DC24V＋7

ー8

3

2

1

4

N.C

Pot

entio

nmet

er

OutputOutput Circuit

＋5ー6

Span Zero


Transmitter

89

TERMINAL TYPE TRANSMITTERTZ-5C

Features

•Input K sensor

•Isolated input/output/power supply

•DIN rail mount

•Small size and easy installation

Input SpecificationsSensor type K


General SpecificationsAccuracy: ±0.4% F.STemp. Coefficient: ±300ppm/˚C F.S (TYP.)Response Time: Less than 0.5sec (0~90%) (TYP.) Load Resistance: DC1~5V more than 2kΩ

DC4~20mA Less than 550ΩDC0~10V more than 4kΩ

Insulated resistance: Input/output/power supply more than100MΩ(DC500V)

Dielectric Stregth: Input/output/power supply AC2000V/1min.Power Supply: DC24V+15%,

-5%Power Consumption: Less than 60mAOperation Temp: -5~50˚Cless than 90%RHCold Junction Compensator: ±1˚C at 20˚C±10˚C

12Y

0 ~ 500°C 0 ~ 1000°C Special(0 ~ 1000°C)Span(300 ~ 1000°C)

Temp. rangeCode No.

123Y

DC 1~5VDC 4~20mA DC 0~10VSpecial(Current less than 20mA)(Voltage less than ±10V)

OutputCode No.

Ordering Guide

TZ-5C-

Output

Input1. 0~500°C2. 0~1000°CY. Special


Dimension

98

9454

2541

Side

Front

DIN RAIL2 4 6 8

5 71 3

Connection Diagram

Block Diagram

OUTPUT1 3 5

2 4 6

7

8LO

ADDC

24V

TCJ Senser+

-K Sensor

Circuit


Input Circuit

IsolationAMP

Output

DC24V

Output

＋5ー6

＋7

ー8

4

2

1

3

N.C

N.C

Span Zero

Input

Burn out

Cold junctionCompensation

Circuit

+

ー

Sensor


Tran

smitt


TZ-5D Features

• Input AC current(True-RMS)

• Isolated input/output/power supply

•DIN rail mount


Input /Output Specification

General SpecificationsAccuracy: ±0.1% F.SInput Frequency: 40Hz~1kHzTemp. Coefficient: ±200ppm/˚C (Typ.)Response Time: Less than 0.5sec (0~90%) Power Supply: DC24V+15% less than 55mA

-5%Operation Temp: -5~50˚C less than 90%RHInsulated Resistance: Input/output/power supply more than

100MΩ(DC500V)Dielectric Strength: Input/output/power supply AC1500V/1min.

123456Y

AC 0~1AAC 0~1AAC 0~1AAC 0~5AAC 0~5AAC 0~5A

Special

Intput

DC 1~5VDC 4~20mADC 0~10VDC 1~5VDC 4~20mADC 0~10V

OutputCode No.

Special AC current input: Less than 0~5A,Min span AC1A DC current output: Less than DC20mA,Min span DC1mA DC voltage output: Less than DC±10V,Min span DC1V Load resistance: DC 1~5V more than 2kΩ

DC 0~10V more than 4kΩDC 4~20mA less than 550Ω

Dimension

98

9454

2541

Side

Front

DIN RAIL2 4 6 8

5 71 3

Connection Diagram

Block Diagram

INPUT OUTPUT1 3 5

2 4 6

7

8

LOA

DDC24V

Circuit


Output

DC24V

Output

＋5ー6

＋7

ー8

3

2

1

4

N.C

SpanZero

Input

RMS CircuitC/T Isolation

Output InputTZ-5D-DC 1~5VDC 4~20mADC 0~10VDC 1~5VDC 4~20mADC 0~10V

1. AC 0~1A2. AC 0~1A3. AC 0~1A4. AC 0~5A5. AC 0~5A6. AC 0~5AY. Special

Ordering Guide


Transmitter

91

TERMINAL TYPE TRANSMITTERTZ-5E

Features

•Input AC voltage


•Power supply DC24V

•DIN rail mount

•Small size easy installation



General SpecificationsAccuracy: ±0.1% F.STemp. coefficient: ±200ppm/˚C F.S (Typ.)Response time: 70mS (Typ) 0~90%Input frequency: 40H~1KHzDielectric stregth: Input/output/power supply AC2000V/l min.Insulated resistance: Input/output/power supply more than 100MΩ

at DC500VOperating temp.: -5˚C~50˚C (less than 90% RH)Power supply: DC24V -5%, +10%

567Y

AC 0~35VAC 0~110VAC 0~150VSpecial

InputCode No.

Special specification Voltage: less than AC300V, min span AC4V

123Y

DC 1~5VDC 4~20mADC 0~10V

Special

Output

More then 2kΩ More then 550Ω More then 4kΩ

Load resistanceCode No.

Special specification Current: less than 20mA,min span 1mA Voltage: less than ±10V,min span 1V

Dimension

98

9454

2541

Side

Front

DIN RAIL2 4 6 8

5 71 3

Connection Diagram

Block Diagram

AC OUTPUT1 3 5

2 4 6

7

8

LOA

DDC24V

Circuit


IsolationAMP

Output

DC24V

Output

＋5ー6

＋7

ー8

3

2

1

4

N.C

Span Zero

Input

RMSConversion

TZ-5E-

Output

Input

5. AC 0~35V6. AC 0~110V7. AC 0~150VY. Special


Ordering Guide


Tran

smitt

er

Dimension

98

9454

2541

Side

Front

DIN RAIL2 4 6 8

5 71 3

TERMINAL TYPE TRANSMITTERTZ-5F

Features

•Input small current and voltage


•Power supply DC24V

•DIN rail mount




General SpecificationsLoad resistance: More than 2KΩ( at 1~5V)

More than 4KΩ( at 0~10V)Less than 550Ω( at 4~20mA)

Accuracy: ±0.25% F.STemp. coefficient: ±200ppm/˚C F.S (Typ.)Response time: Less than 0.1sec 0~90%Dielectric stregth: Input/output/power supply AC2000V/l min.Insulated resistance: Input/output/power supply more than 100MΩ

at DC500VOperating temp.: -5˚C~50˚C (less than 90% RH)Power supply: DC24V -5%, +15%

123Y

DC 0~10mVDC 0~50mVDC 0~100µASpecial

InputCode No.

Special specification Current: less than 1mA, min span 10µA Voltage: less than 100V, min span 5mV

123Y

DC 1~5V DC 4~20mADC 0~10VSpecial

OutputCode No.

Special specification Current: less than 20mA, min span 1mA Voltage: less than ±10V, min span 1V

Connection Diagram

Block Diagram

INPUT OUTPUT1 3 5

2 4 6

7

8

LOA

DDC24V

Circuit


Input Conversion

IsolationAMP

Output

DC24V

Output

＋5ー6

＋7

ー8

4

1

2

3

N.C

Span Zero

Input

Ordering GuideTZ-5F-

Output

Input

1. DC 0~10mV2. DC 0~ 50mV3. DC 0~100μAY. Special

1. DC 1~5V 2. DC 4~20mA 3. DC 0~10VY. Special


DIGITAL PANEL METERACCESSORIES

Shunt Resistor (20A, 60A)

20A/200 mV±0.5%

60A/ 60 mV±0.5%

Power Supply

Splash Proof Cover (WP)

• Dimensions 59 mm(H) ｴ 170 mm(W) ｴ 18 mm(D)

• Dust-proof and water proof

• Available bracket installation 1/8 DIN case

IP66 COVER (WP-3)

80 2-4.1×6φ

6

5

4

1

2

3 37

+5V

DVNC

AC100VG

ND4543

30

69±0.5

Model No. Input voltage Output voltage Output current

APS-250-1

APS-250-2

APS-240-1

APS-240-2

90~132VAC

180~264VAC

90~132VAC

180~264VAC

4.85~5.15V

24V±10%

Max 250mA

80mA

(Input voltage is selectable internal switch)

140

Fittng hole distance 120mm

Height 50

107

59


MODEL RANGE DIVIDE RATIO RESOLUTIONINTERNALRESISTANCE

MAX. INPUTVOLTAGE

ACCURACYTEMPERATURECOEFFICIENT

ADV-501-12ADV-501-13ADV-501-14ADV-501-15

± 2V± 20V± 200V±2000V

1/101/1001/10001/10000

1mV10mV

100mV1V

1MΩ10MΩ10MΩ

100MΩ

less than ± 200V± 750V± 750V±2500V

less than 0.1%0.1%0.1%0.1%

± 50PPM± 50PPM± 50PPM±100PPM

MODEL RANGE DIVIDE RATIO RESOLUTIONINTERNALRESISTANCE

MAX. INPUTVOLTAGE

ACCURACYTEMPERATURECOEFFICIENT

ADV-502-14ADV-502-15

± 200V±2000V

1/1001/1000

100mV1V

10MΩ100MΩ

less than ± 750V±2500V

less than 0.1%0.1%

± 50PPM± 100PPM

MODEL RANGE RESOLUTIONINTERNALRESISTANCE ACCURACY

ASH-400-19ASH-400-20ASH-400-21ASH-400-22ASH-400-23ASH-400-24ASH-400-25ASH-400-26

±1.999µA±19.99µA±199.9µA±1.999mA±19.99mA±199.9mA

±1.999A±5.00A

100kΩ10kΩ1kΩ

100Ω10Ω1Ω

0.1Ω 0.01Ω

1nA10nA

100nA1µA

10µA100µA

1mA10mA

± 1%±1digit±0.5%±1digit±0.2%±1digit±0.2%±1digit±0.2%±1digit±0.3%±1digit±0.3%±1digit

±1%±1digit

INPUT MAX.CURRENT

less than±1mA± 5mA± 10mA± 50mA±150mA±500mA

±3A±8A

DIGITAL PANEL METERACCESSORIES

VOLTAGE DIVIDER

･FOR USE 0.2V RANGE(11 Range)

DIMENSIONS CONNECTION DIAGRAM

･FOR USE 2V RANGE(12 Range)

SHUNT

･FOR USE 0.2V(11 Range)

95

MEMO

96

MEMO

June 2004(KS)

DIG

ITAL PA

NEL M

ETER, TRASM

ITTER CATA

LOG

UE　

2004

33-6, YAGUCHI 2-CHOME, OHTA-KU,TOKYO 146-8505, JAPANFAX :(03)3757-2989PHONE :(03)3579-3893E-mail :[email protected]

We reserve the right to change specifications without notice.

Catalogue 2004 - Micronix Plus | Termoviziune - Aparate ... · PDF fileCatalogue 2004. SPECIAL...

Documents

Transcript of Catalogue 2004 - Micronix Plus | Termoviziune - Aparate ... · PDF fileCatalogue 2004. SPECIAL...