Catalogo General de Repetidores

Last Modified LGPAllgon Repeaters

Repeater products Product list

Standard Compact Combi Band Selective Band Selective Dual Band 800 MHz 800MHz Standard 900 MHz 900 MHz Compact 1800 MHz 1800 MHz 1900 MHz 1900 MHz WCDMA EGSM Standard / Compact

Channel Selective (GSM) Moving repeaters 900 MHz Maritime 1800 MHz In-train 1900 MHz EGSM/RGSM CDMA Allgon Fiber 1900 MHz Allgon Fiber optic system 800 MHz

Mechanical Drawings Options and features Standard Low Repeater Options & Features Standard High OMS Compact Low Fibre Optic Transceiver Compact High Fibre Optic Node Conformity Allgon Repeater Conformity Repeater Certificates

Standard 800 MHz Band Selective

Product Description

AR4200_052AR4200_053 25 MHz BWAR4600_052 IDEN

ALLGON SYSTEM AB Utfärdare/Issued by

Kjell Knuutinen Dattum/Date

2003-06-07 Godkänd/Approved

Dok nr/Doc no

AR4200/052-201 Rev

G Sida/Page

1 Dok namn/Doc name PRODUCT SPECIFICATION

Fil/file

AR4200_052_G.doc

Specification of a Band selective Repeater

800 MHz Product Number: AR4200/052

1. Electrical specification (typical value) The repeater complies with the requirements of FCC Frequency band Up link 824 - 849 MHz Frequency band Down link 869 - 894 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-16.9 MHz Filter setting resolution 25 kHz Selectivity BW 3dB 16.9 MHz Selectivity BW 45dB BW 3dB + 1.2 MHz Selectivity BW 50dB BW 3dB + 2.2 MHz Pass band ripple 5 dB Output power, PEP +36 dBm Output power 2 carrier +30 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 160 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female




Dok nr/Doc no

AR4200/053-201 Rev

C Sida/Page


Fil/file

AR4200_053_C.doc


800 MHz, 25 MHz BW version Product Number: AR4200/053

1. Electrical specification (typical values) The repeater complies with the requirements of FCC Frequency band Up link 824 - 849 MHz Frequency band Down link 869 - 894 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-25 MHz Filter setting resolution 25 kHz Selectivity BW 3dB 25 MHz Selectivity BW 20dB BW 3dB + 1.2 MHz Selectivity BW 30dB BW 3dB + 2.0 MHz Pass band ripple 6 dB Output power, PEP +36 dBm Output power 2 carrier +30 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage 115 V AC Power consumption, max 160 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female




Dok nr/Doc no

AR4600/052-201 Rev

E Sida/Page


Fil/file

AR4600_052_E.doc

Specification of a Band selective Repeater IDEN, 800 MHz

Product number: AR4600/052 1. Electrical specification (typical values) The repeater complies with the requirements of FCC

Frequency band Up link 806 – 825 MHz Frequency band Down link 851 - 870 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation –25 to +55 ºC 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-16.9 MHz Filter setting resolution 25 KHz Selectivity BW 3dB 16.9 MHz Selectivity BW 45dB BW 3dB + 1.2 MHz Selectivity BW 50dB BW 3dB + 2.2 MHz Pass band ripple 4 dB Output power, PEP +36 dBm Output power 2 carrier +30 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage 115 V AC Power consumption, typ. (max) 160 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 F Casing class NEMA4/IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female


Product Description

AR1200_052 16,5 MHz BWAR1200_053 25 MHz BW




Dok nr/Doc no

AR1200/052-201 Rev

G Sida/Page


Fil/file

AR1200_052_G.doc


900 MHz Product Number: AR1200/052

1. Electrical specification (typical values) The repeater complies with the requirements of ETS 300 609-4 Frequency band Up link 890 - 915 MHz Frequency band Down link 935 - 960 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation -25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-16.9 MHz Filter setting resolution 25 kHz Automatic gain control Implemented Selectivity BW 3dB 16.9 MHz Selectivity BW 45dB BW 3dB + 1.2 MHz Selectivity BW 50dB BW 3dB + 2.2 MHz Pass band ripple 4 dB Output power, PEP +29 dBm Output power 2 carrier +23 dBm/carrier Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 160 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female




Dok nr/Doc no

AR1200/053-201 Rev

C Sida/Page


Fil/file

AR1200_053_C.doc

STANDARD Band selective Repeater 900 MHz, 25 MHz BW

Product Number: AR1200/053

1. Electrical specification (typical values) The repeater complies with the requirements of ETS 300 609-4 Frequency band Up link 890 - 915 MHz Frequency band Down link 935 - 960 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation -25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-25 MHz Filter setting resolution 25 kHz Automatic gain control Implemented Selectivity BW 3dB 25 MHz Selectivity BW 35dB BW 3dB + 1.2 MHz Selectivity BW 45dB BW 3dB + 2.2 MHz Pass band ripple 6 dB Output power, PEP +29 dBm Output power 2 carrier +23 dBm/carrier Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 160 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female


Product Description

AR2200_001 Low BandAR2200_901 High Band




Dok nr/Doc no

AR2200/001-201 Rev

F Sida/Page


Fil/file

AR2200_001_F.doc


1800 MHz, Lower band Product Number: AR2200/001

1. Electrical specification (typical values) The repeater complies with the requirements of ETS 300 609-4

Frequency band Up link 1710 – 1765 MHz Frequency band Down link 1805 - 1860 MHz Duplex spacing 95 MHz Absolute group delay < 6 µs Antenna isolation supervision Continuously Filter bandwidth (remotely adjustable) 0.5 - 16.9 MHz Filter setting resolution 25 KHz Gain adjustment range (in 1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Selectivity BW 3 dB 16.9 MHz Selectivity BW 45 dB BW3 dB + 1.2 MHz Selectivity BW 50 dB BW3 dB + 2.2 MHz Pass band ripple 6 dB Output power, PEP + 32 dBm Output power 2 carrier + 26 dBm/carrier Automatic gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 160 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female




Dok nr/Doc no

AR2200/901-201 Rev

F Sida/Page


Fil/file

AR2200_901_F.doc


1800 MHz, Upper band Product Number: AR2200/901

1. Electrical specification (typical values) The repeater complies with the requirements of ETS 300 609-4 Frequency band Up link 1730 – 1785 MHz Frequency band Down link 1825 - 1880 MHz Duplex spacing 95 MHz Absolute group delay < 6 µs Antenna isolation supervision Continuously Filter bandwidth (remotely adjustable) 0.5 - 16.9 MHz Filter setting resolution 25 KHz Gain adjustment range (in 1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C 6 dB Selectivity BW 3 dB 16.9 MHz Selectivity BW 45 dB BW3 dB + 1.2 MHz Selectivity BW 50 dB BW3 dB + 2.2 MHz Pass band ripple 6 dB Output power, PEP + 32 dBm Output power 2 carrier + 26 dBm/carrier Automatic gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 160 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female


Product Description

AR3400_001 Low BandAR3400_901 High Band




Dok nr/Doc no

AR3400/001-201 Rev

E Sida/Page


Fil/file

AR3400_001_E.doc

Specification of a band selective repeater 1900 MHz version, Lower band Product number: AR3400/001

1. Electrical specification (typical value) The repeater complies with the FCC requirements

Frequency band Up link 1850 – 1890 MHz Frequency band Down link 1930 – 1970 MHz Duplex spacing 80 MHz Absolute group delay < 6 µs Antenna isolation supervision Continuously Filter bandwidth (remotely adjustable) 0.5 – 16.9 MHz Filter setting resolution 25 KHz Gain adjustment range (in 1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Selectivity BW3 dB 16.9 MHz Selectivity BW 45 dB BW3 dB + 1.2 MHz Selectivity BW 50 dB BW3 dB + 2.2 MHz Passband ripple 6 dB Max output power + 36 dBm Output power 2 carrier + 30 dBm Automat gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, nom. (max) 130 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class NEMA4/IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female




Dok nr/Doc no

AR3400/901-201 Rev

E Sida/Page


Fil/file

AR3400_901_E.doc

Specification of a band selective repeater

1900 MHz version, Upper band Product number: AR3400/901

1. Electrical specification (typical values) The repeater complies with FCC requirements

Frequency band Up link 1870 – 1910 MHz Frequency band Down link 1950 - 1990 MHz Duplex spacing 80 MHz Absolute group delay < 6 µs Antenna isolation supervision Continuously Filter bandwidth (remotely adjustable) 0.5 - 16.9 MHz Filter setting resolution 25 KHz Gain adjustment range (in 1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Selectivity BW 3 dB 16.9 MHz Selectivity BW 45 dB BW3 dB + 1.2 MHz Selectivity BW 50 dB BW3 dB + 2.2 MHz Pass band ripple 6 dB Max output power + 36 dBm Output power 2 carrier + 30 dBm Automat gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 VAC Power consumption, nom. (max) 130 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class NEMA4/IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female

Standard 800 MHz CDMA

Product Description AR4500_0014 2 Channel AR4500_0514 2 Channel, MRX AR4540_0514 2 Channel, High Power, MRX AR4200_012 Band selective, 25 MHz




Dok nr/Doc no

AR4500/0014-201 Rev

B Sida/Page

1 Dok namn/Doc name PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR4500_0014_B.doc

Specification of a CDMA 800 channel selective repeater 2-channel version, standard


1. Electrical specification (typical values) The repeater complies with the requirements of FCC

Frequency band Reverse link 824 - 849 MHz Frequency band Forward link 869 - 894 MHz Number of channels 2 Duplex spacing 45 MHz Gain adjustment range (1 dB steps) 60-90 dB Gain variation in temperature < 4 dB Absolute group delay < 6 µs Output power, RMS, one carrier +33 dBm Output power RMS, two carrier +28 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented Selectivity ±615 kHz > -3 dB Selectivity ±885 kHz < -50 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 3,5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Antenna isolation supervision and regulation No Antenna VSWR supervision No Power supply voltage (default) 115 V AC Power consumption, max 160 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female




Dok nr/Doc no

AR4500/0514-201 Rev

B Sida/Page


Fil/file

AR4500_0514_B.doc

Specification of a CDMA 800 channel selective repeater 2-channel version, standard with MRX



Frequency band Reverse link 824 - 849 MHz Frequency band Forward link 869 - 894 MHz Number of channels 2 Duplex spacing 45 MHz Gain adjustment range (1 dB steps) 60-90 dB Gain variation in temperature < 4 dB Absolute group delay < 6 µs Output power, RMS, one carrier +33 dBm Output power RMS, two carrier +28 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented Selectivity ±615 kHz > -3 dB Selectivity ±885 kHz < -50 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 3,5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Antenna isolation supervision and regulation Yes (MRX) Antenna VSWR supervision Yes (MRX) Power supply voltage (default) 115 V AC Power consumption, max 160 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female




Dok nr/Doc no

AR4540/0514-201

Rev

B Sida/Page

1

Dok namn/Doc name PRELIMINARY PRODUCT SPECIFICATION

Fil/file

AR4540_0514_B.doc

Specification of a CDMA 800 channel selective repeater 2-channel version, High Power with MRX

Product Number: AR4540/0514 1. Electrical specification (typical values) The repeater complies with the requirements of FCC

Frequency band Reverse link 824 - 849 MHz Frequency band Forward link 869 - 894 MHz Number of channels 2 Duplex spacing 45 MHz Gain adjustment range (1 dB steps), DL 65-95 dB Gain adjustment range (1 dB steps), UL 60-90 dB Gain variation in temperature < 4 dB Absolute group delay < 6 µs Output power, RMS, one carrier Forward +38 dBm Output power RMS, two carrier Forward +33 dBm/carrier Output power, RMS, one carrier Reverse +33 dBm Output power RMS, two carrier Reverse +28 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented Selectivity ±615 kHz > -3 dB Selectivity ±885 kHz < -50 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 3,5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Antenna isolation supervision and regulation Yes (MRX) Antenna VSWR supervision Yes (MRX) Power supply voltage (default) 115 V AC Power consumption, max 320 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.5 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female




Dok nr/Doc no

AR4200/012-201 Rev

C Sida/Page


Fil/file

AR4200_012_C.doc

Specification of a Band selective Repeater CDMA 800 MHz, 25 MHz BW version

Product Number: AR4200/012 1. Electrical specification (typical values) The repeater complies with the requirements of FCC Frequency band Reverse link 824 - 849 MHz Frequency band Forward link 869 - 894 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-25 MHz Filter setting resolution 25 kHz Selectivity BW 3dB 25 MHz Selectivity BW 35dB BW 3dB + 1.2 MHz Selectivity BW 45dB BW 3dB + 2.2 MHz Pass band ripple 6 dB Output power RMS, one carrier, DL +33 dBm Output power RMS, one carrier, UL +30 dBm Output power RMS, two carrier, DL +28 dBm/carrier Output power RMS, two carrier, UL +25 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 4 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage 115 V AC Power consumption, max 160 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female

Standard 900 MHz GSM Channel Selective

Product Description

AR1100_002 2 ChannelAR1100_004 4 ChannelAR1111_006 6 ChannelAR1111_008 8 Channel




Dok nr/Doc no

AR1100/002-201 Rev

E Sida/Page


Fil/file

AR1100_002_E.doc

Specification of a GSM 900 channel selective repeater

2-channel version Product Number: AR1100/002


Frequency band Up link 890 - 915 MHz Frequency band Down link 935 - 960 MHz Number of channels 2 Duplex spacing 45 MHz Absolute group delay < 5 µs Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Antenna isolation supervision Continuously Group delay variation within any ± 100KHz segment in the pass band

<± 200 ns

Output power per channel +33 dBm Automatic gain control Implemented Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1 MHz < -50 dB Selectivity ± 5 MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 85 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 2. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female




Dok nr/Doc no

AR1100/004-201 Rev

E Sida/Page


Fil/file

AR1100_004_E.doc




Frequency band Up link 890 - 915 MHz Frequency band Down link 935 - 960 MHz Number of channels 4 Duplex spacing 45 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segment in the pass band

<± 200 ns

Output power per channel +30 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1 MHz < -50 dB Selectivity ± 5 MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 155 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female




Dok nr/Doc no

AR1111/006-201 Rev

E Sida/Page


Fil/file

AR1111_006_E.doc





<± 200 ns

Output power per channel +27 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1 MHz < -50 dB Selectivity ± 5 MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 230 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female




Dok nr/Doc no

AR1111/008-201 Rev

E Sida/Page


Fil/file

AR1111_008_E.doc





<± 200 ns

Output power per channel +27 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1 MHz < -50 dB Selectivity ± 5 MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 305 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female


Product Description

AR2100_002 2 Channel, Low BandAR2100_004 4 Channel, Low BandAR2100_902 2 Channel, High BandAR2100_904 4 Channel, High BandAR2121_006 6 Channel, Low BandAR2121_008 8 Channel, Low BandAR2121_906 6 Channel, High BandAR2121_908 8 Channel, High Band




Dok nr/Doc no

AR2100/002-201 Rev

E Sida/Page


Fil/file

AR2100_002_E.doc


2-channel version, Lower band Product Number: AR2100/002

1. Electrical specification (typical values) The repeater complies with the requirements of ETS 300609-4


<± 200 ns

Output power per channel +33 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 85 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female




Dok nr/Doc no

AR2100/004-201 Rev

E Sida/Page


Fil/file

AR2100_004_E.doc




Frequency band Up link 1710 - 1765 MHz Frequency band Down link 1805 - 1860 MHz Number of channels 4 Duplex spacing 95 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55°C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segment in the pass band

<± 200 ns





Dok nr/Doc no

AR2100/902-201 Rev

E Sida/Page


Fil/file

AR2100_902_E.doc


2-channel version, Upper band Product Number: AR2100/902


Frequency band Up link 1730 – 1785 MHz Frequency band Down link 1825 – 1880 MHz Number of channels 2 Duplex spacing 95 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segment in the pass band

<± 200 ns





Dok nr/Doc no

AR2100/904-201 Rev

E Sida/Page


Fil/file

AR2100_904_E.doc





<± 200 ns





Dok nr/Doc no

AR2121/006-201 Rev

E Sida/Page


Fil/file

AR2121_006_E.doc





<± 200 ns

Output power per channel +27 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 230 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female




Dok nr/Doc no

AR2121/008-201 Rev

E Sida/Page


Fil/file

AR2121_008_E.doc





<± 200 ns





Dok nr/Doc no

AR2121/906-201 Rev

E Sida/Page


Fil/file

AR2121_906_E.doc





<± 200 ns





Dok nr/Doc no

AR2121/908-201 Rev

E Sida/Page


Fil/file

AR2121_908_E.doc


8 channel version, Upper band Product Number: AR2121/908



<± 200 ns



Product Description

AR3100_002 2 Channel, Low BandAR3100_004 4 Channel, Low BandAR3100_902 2 Channel, High BandAR3100_904 4 Channel, High BandAR3131_006 6 Channel, Low BandAR3131_008 8 Channel, Low BandAR3131_906 6 Channel, High BandAR3131_908 8 Channel, High Band




Dok nr/Doc no

AR3100/002-201 Rev

E Sida/Page


Fil/file

AR3100_002_E.doc



1. Electrical specification (typical values) The repeater complies with the FCC requirements

Frequency band Up link 1850 -1890 MHz Frequency band Down link 1930 - 1970 MHz Number of channels 2 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segment in the pass band

<± 200 ns





Dok nr/Doc no

AR3100/004-201 Rev

E Sida/Page


Fil/file

AR3100_004_E.doc





<± 200 ns





Dok nr/Doc no

AR3100/902-201 Rev

E Sida/Page


Fil/file

AR3100_902_E.doc


2-channel version, High band Product Number: AR3100/902


Frequency band Up link 1870 –1910 MHz Frequency band Down link 1950 - 1990 MHz Number of channels 2 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Group delay variation within any ± 100KHz segment in the pass band

<± 200 ns





Dok nr/Doc no

AR3100/904-201 Rev

E Sida/Page


Fil/file

AR3100_904_E.doc





<± 200 ns





Dok nr/Doc no

AR3131/006-201 Rev

E Sida/Page


Fil/file

AR3131_006_E.doc





<± 200 ns





Dok nr/Doc no

AR3131/008-201 Rev

E Sida/Page


Fil/file

AR3131_008_E.doc





<± 200 ns





Dok nr/Doc no

AR3131/906-201 Rev

E Sida/Page


Fil/file

AR3131_906_E.doc





<± 200 ns





Dok nr/Doc no

AR3131/908201 Rev

E Sida/Page


Fil/file

AR3131_908_E.doc





<± 200 ns


Standard 1900 MHz CDMA

Product Description AR3500_001 2 Channel, Low Band AR3500_901 2 Channel, High Band AR3530_001 2 Channel, Low Band, High Power AR3530_051 2 Channel, Low Band, High Power, MRX AR3530_901 2 Channel, High Band, High Power AR3530_951 2 Channel, High Band, High Power, MRX AR3535_022 4 Channel, Low Band, 2+2 AR3535_922 4 Channel, High Band, 2+2 AR3400_011 Band selective, Low band AR3400_911 Band selective, High band




Dok nr/Doc no

AR3500/001-201 Rev

H Sida/Page


Fil/file

AR3500_001_H.doc

Specification of a CDMA 1900 channel selective repeater

2-channel version, Lower band Product number: AR3500/001


Frequency band Reverse link 1850 -1890 MHz Frequency band Forward link 1930 - 1970 MHz Number of channels 2 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 5 µs Output power, RMS, one carrier +33 dBm Output power RMS, two carrier +27 dBm/carrier Automatic gain control Implemented Selectivity ± 615 kHz > -3 dB Selectivity ± 885 kHz < -50 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 160 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female




Dok nr/Doc no

AR3500/901-201 Rev

H Sida/Page


Fil/file

AR3500_901_H.doc


2-channel version, Upper band Product number: AR3500/901

1. Electrical specification (typical value) The repeater complies with FCC requirements

Frequency band Reverse link 1870 –1910 MHz Frequency band Forward link 1950 - 1990 MHz Number of channels 2 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 6 µs Output power, RMS, one carrier +33 dBm Output power RMS, two carrier +27 dBm/carrier Automatic gain control Implemented Selectivity ± 615 kHz > -3 dB Selectivity ± 885 kHz < -50 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 320 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female




Dok nr/Doc no

AR3530/001-201 Rev

E Sida/Page


Fil/file

AR3530_001_E.doc

Specification of a CDMA 1900 channel selective repeater 2-channel version, Lower band

High Power Product Number: AR3530/001

1. Electrical specification (typical value) The repeater complies with FCC requirements

Frequency band Reverse link 1850 –1890 MHz Frequency band Forward link 1930 - 1970 MHz Number of channels 2 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 6 µs Output power, RMS, one carrier Forward +38 dBm Output power RMS, two carrier Forward +33 dBm/carrier Output power, RMS, one carrier Reverse +33 dBm Output power RMS, two carrier Reverse +28 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented Selectivity ± 615 kHz > -3 dB Selectivity ± 885 kHz < -50 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Antenna isolation supervision and regulation MRX receiver implemented Antenna VSWR supervision MRX receiver implemented Power supply voltage (default) 115 V AC Power consumption, max 320 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.5 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female




Dok nr/Doc no

AR3530/051-201 Rev

C Sida/Page


Fil/file

AR3530_051_C.doc

Specification of a CDMA 1900 channel selective repeater 2-channel version, Lower band

High Power, MRX Product Number: AR3530/051

1. Electrical specification (typical values) The repeater complies with the requirements to FCC

Frequency band Reverse link 1850 –1890 MHz Frequency band Forward link 1930 - 1970 MHz Number of channels 2 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) UL 50-90 dB Gain adjustment range (1 dB steps) DL 60-100 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 6 µs Output power, RMS, one carrier Forward +38 dBm Output power RMS, two carrier Forward +33 dBm/carrier Output power, RMS, one carrier Reverse +33 dBm Output power RMS, two carrier Reverse +28 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented Selectivity ± 615 kHz > -3 dB Selectivity ± 885 kHz < -50 dB Band pass ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Antenna isolation supervision and regulation MRX receiver implemented Antenna VSWR supervision MRX receiver implemented Power supply voltage (default) 115 V AC Power consumption, max 320 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.5 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female




Dok nr/Doc no

AR3530/951-201 Rev

C Sida/Page


Fil/file

AR3530_951_C.doc

Specification of a CDMA 1900 channel selective repeater 2-channel version, Upper band

High Power, MRX Product Number: AR3530/951


Frequency band Reverse link 1870 –1910 MHz Frequency band Forward link 1950 - 1990 MHz Number of channels 2 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) UL 50-90 dB Gain adjustment range (1 dB steps) DL 60-100 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 6 µs Output power, RMS, one carrier Forward +38 dBm Output power RMS, two carrier Forward +33 dBm/carrier Output power, RMS, one carrier Reverse +33 dBm Output power RMS, two carrier Reverse +28 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented Selectivity ± 615 kHz > -3 dB Selectivity ± 885 kHz < -50 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Antenna isolation supervision and regulation MRX receiver implemented Antenna VSWR supervision MRX receiver implemented Power supply voltage (default) 115 V AC Power consumption, max 320 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female




Dok nr/Doc no

AR3535/022-201 Rev

D Sida/Page


Fil/file

AR3535_022_D.doc



§ True 2+2 CDMA channels in one package § The antenna connections 2+2 channels can either be combined (3dB loss) or separated


Frequency band Reverse link 1850 -1890 MHz Frequency band Forward link 1930 - 1970 MHz Number of channels 4 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 6 µs Output power, RMS, two carrier (no combiner) +33 dBm Output power RMS, four carrier (no combiner) +28 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented Selectivity ± 615 kHz > -3 dB Selectivity ± 885 kHz < -50 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 320 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY




Dok nr/Doc no

AR3535/922-201 Rev

D Sida/Page


Fil/file

AR3535_922_D.doc



§ True 2+2 CDMA channels in one package § The antenna connections 2+2 channels can either be combined (3dB loss) or separated


Frequency band Reverse link 1870 -1910 MHz Frequency band Forward link 1950 - 1990 MHz Number of channels 4 Duplex spacing 80 MHz Gain adjustment range (1 dB steps) 50-90 dB Gain (max variation –25 to +55 °C) 4 dB Absolute group delay < 6 µs Output power, RMS, two carrier (no combiner) +33 dBm Output power RMS, four carrier (no combiner) +28 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented Selectivity ±615 kHz > -3 dB Selectivity ±885 kHz < -50 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 320 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.5 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female




Dok nr/Doc no

AR3400/011-201 Rev

D Sida/Page


Fil/file

AR3400_011_D.doc


CDMA 1900 MHz version, Lower band Product number: AR3400/011

1. Electrical specification (typical value) The repeater complies with the FCC requirements

Frequency band Reverse link 1850 – 1890 MHz Frequency band Forward link 1930 – 1970 MHz Duplex spacing 80 MHz Absolute group delay < 6 µs Antenna isolation supervision Continuously Filter bandwidth (remotely adjustable) 0.5 – 16.9 MHz Filter setting resolution 25 KHz Gain adjustment range (in 1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Selectivity BW 3 dB 16.9 MHz Selectivity BW 45 dB BW3 dB + 1.2 MHz Selectivity BW 50 dB BW3 dB + 2.2 MHz Passband ripple 6 dB Output power RMS, one carrier, DL + 33 dBm Output power RMS, one carrier, UL +30 dBm Output power RMS, two carrier, DL + 28 dBm Output power RMS, two carrier, UL +25 dBm Automatic gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 160 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class NEMA4/IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female




Dok nr/Doc no

AR3400/901-201 Rev

D Sida/Page


Fil/file

AR3400_911_D.doc


CDMA 1900 MHz version, Upper band Product number: AR3400/911


Frequency band Reverse link 1870 – 1910 MHz Frequency band Forward link 1950 - 1990 MHz Duplex spacing 80 MHz Absolute group delay < 6 µs Antenna isolation supervision Continuously Filter bandwidth (remotely adjustable) 0.5 - 16.9 MHz Filter setting resolution 25 KHz Gain adjustment range (in 1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Selectivity BW 3 dB 16.9 MHz Selectivity BW 45 dB BW3 dB + 1.2 MHz Selectivity BW 50 dB BW3 dB + 2.2 MHz Pass band ripple 6 dB Output power RMS, one carrier, DL + 33 dBm Output power RMS, one carrier, UL + 30 dBm Output power RMS, two carrier, DL + 28 dBm Output power RMS, two carrier, UL + 25 dBm Automatic gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 VAC Power consumption, max 160 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class NEMA4/IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female

Compact 800 MHz Band Selective

Product Description ALR4200_001 Adjustable 15 MHz BW ALR4200_002 Adjustable 25 MHz BW ALR4600_001 iDEN ALR4200_011 CDMA 15 MHz ALR4200_012 CDMA 25 MHz


Product Description

ALR1200_001 Adjustable 15 MHz BWALR1200_002 Adjustable 25 MHz BWALR1200_901 EGSM, Adj. 15 MHz BW


Product Description

ALR2200_001 Adjustable BW, Low BandALR2200_901 Adjustable BW, High Band


Kjell Knuutinen

Dattum/Date

2003-06-10

Godkänd/Approved

Dok nr/Doc no

ALR2200/001-201

Rev

F

Sida/Page

Dok namn/Doc name PRODUCT SPECIFICATION

Fil/file

ALR2200-001_F.doc

COMPACT repeater with adjustable bandwidth

1800 MHz version, Low band Product Number: ALR2200/001

1. Electrical specification (typical values) The repeater complies with the requirement of ETS 300 609-4

Frequency tuning band Up link 1710 – 1765 MHz Frequency tuning band Down link 1805 – 1860 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 95 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55°C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 26 dBm Output power, 2 carrier + 20 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class NEMA4/IP65 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 4.3 Inches 385 x 385 x 110 mm Mechanical outline See Compact Low Weight < 22 lbs < 10 kg RF connectors N-type female


Kjell Knuutinen

Dattum/Date

2003-06-10

Godkänd/Approved

Dok nr/Doc no

ALR2200/901-201

Rev

F

Sida/Page


Fil/file

ALR2200-901_F.doc


1800 MHz version, High band Product Number ALR2200/901

1. Electrical specification (typical values) The repeater complies with the requirement of ETS 300609-4

Frequency tuning band Up link 1730 – 1785 MHz Frequency tuning band Down link 1825 – 1880 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 95 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 26 dBm Output power, 2 carrier + 20 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class NEMA4/IP65 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 4.3 Inches 385 x 385 x 110 mm Mechanical outline See Compact Low Weight < 22 lbs < 10 kg RF-connectors N-type female


Product Description ALR3200_001 Low Band ALR3200_901 High Band ALR3200_011 CDMA Low Band ALR3200_911 CDMA High Band


Kjell Knuutinen

Dattum/Date

2003-06-11

Godkänd/Approved

Dok nr/Doc no

ALR3200/001-201

Rev

F

Sida/Page


Fil/file

ALR3200-001_F.doc


1900 MHz version, Low band Product Number: ALR3200/001



2. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class NEMA4/IP65 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 4.3 Inches 385 x 385 x 110 mm Mechanical outline See Compact Low Weight < 22 lbs < 10 kg RF-connectors N-type female


Kjell Knuutinen

Dattum/Date

2003-06-11

Godkänd/Approved

Dok nr/Doc no

ALR3200/901-201

Rev

F

Sida/Page


Fil/file

ALR3200-901_F.doc


1900 MHz version, High band Product Number: ALR3200/901



2. Environmental specification Temperature range -13 to + 131 °F -25 to + 55 °C Casing class NEMA4/IP65 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 4.3 Inches 385 x 385 x 110 mm Mechanical outline See Compact Low Weight < 22 lbs < 10 kg RF-connectors N-type female Lock type Allgon Safety bolts


Kjell Knuutinen

Dattum/Date

2003-07-18

Godkänd/Approved

Dok nr/Doc no

ALR4200/001-201 Rev

H Sida/Page


Fil/file

ALR4200-001_H.doc

COMPACT repeater with adjustable bandwidth 800 MHz version, 15 MHz BW

Product Number: ALR4200/001 1. Electrical specification (typical value) The repeater complies with the requirements of FCC

Frequency tuning band Up link 824 – 849 MHz Frequency tuning band Down link 869 - 894 MHz Filter bandwidth standard, adjustable 0.5 – 15 MHz Filter setting resolution 12.5 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 28 dBm Output power, 2 carrier + 22 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 65 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W

2. Environmental specification Temperature range -13 to + 131 °F -25 to + 55 °C Casing class NEMA4/IP65 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 4.3 Inches 385 x 385 x 110 mm Mechanical outline See Compact Low Weight < 22 lbs < 10 kg RF-connectors N-type female


Kjell Knuutinen

Dattum/Date

2003-07-18

Godkänd/Approved

Dok nr/Doc no

ALR4200/002-201 Rev

F Sida/Page


Fil/file

ALR4200-002_F.doc


800 MHz version, 25 MHz BW Product Number: ALR4200/002

1. Electrical specification (typical value) The repeater complies with the requirements of FCC

Frequency tuning band Up link 824 – 849 MHz Frequency tuning band Down link 869 - 894 MHz Filter bandwidth standard, adjustable 0.5 – 25 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 28 dBm Output power, 2 carrier + 22 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 65 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W

2. Environmental specification Temperature range -13 to + 131 F -25 to + 55 °C Casing class NEMA4/IP65 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 4.3 Inches 385 x 385 x 110 mm Mechanical outline See Compact Low Weight < 22 lbs < 10 kg RF-connectors N-type female


Kjell Knuutinen

Dattum/Date

2003-06-11

Godkänd/Approved

Dok nr/Doc no

ALR4600/001-201

Rev

G

Sida/Page


Fil/file

ALR4600-001_G.doc


800 MHz version, iDEN/SMR, 15 MHz BW Product Number: ALR4600/001

1. Electrical specification (typical value) The repeater complies with the requirements of FCC

Frequency tuning band Up link 806 – 825 MHz Frequency tuning band Down link 851 – 870 MHz Filter bandwidth standard, adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 28 dBm Output power, 2 carrier + 22 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 65 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W



Kjell Knuutinen

Dattum/Date

2003-06-11

Godkänd/Approved

Dok nr/Doc no

ALR1200/001-201

Rev

H

Sida/Page


Fil/file

ALR1200-001_H.doc


Product Number: ALR1200/001 1. Electrical specification (typical values) The repeater complies with the requirements of ETS 300 609-4




Kjell Knuutinen

Dattum/Date

2003-06-11

Godkänd/Approved

Dok nr/Doc no

ALR1200/002-201

Rev

E

Sida/Page


Fil/file

ALR1200-002_E.doc


Product Number: ALR1200/002




Page: 1 (2) File: Options & Features Date: 2003-02-11

Repeater Options and Features

1. Operation Set-up and commissioning of the repeater via an OM-Online (Operation & Maintenance Terminal) software - Standard computer locally connected via RS232 or RCC - Standard computer remotely connected via modem (optional RCU-kit in the

repeater is then required) 2. Hardware & Software requirements OM-Online require a PC with capacity to run Sun’s Java 2 Standard Edition US-English version 1.4.0_02 or higher on 32-bit Windows operating system. Minimum display resolution 800x600 pixels. MS Windows NT 4.0 SP6, Windows 98 SE or Windows 2000 SP2. Access to IP-repeaters requires installation of RAS (Remote Access Service). CommServer SA102 61/1 R1A can be installed in same computer or accessible over network. 3. Alarms Internal and external alarms locally or remotely monitored - LED sum alarm presentation on repeater front - Large number of internal alarms test points, each having a fixed alarm level - Four alarm ports for external alarm connections (e.g. intruder, fire, temperature

etc), each having flexible alarm level settings Settable alarm levels: q None and ceasing q Warning q Error q Critical

Page: 2 (2) File: Options & Features Date: 2003-02-11

4. Options and facilities q Dual band. Most repeaters can be dual band configured. q R2R (Repeater to Repeater) multidrop link is an advanced feature enabling data

communication between repeaters over one single remote interface (RCU) q Fiber optic kit. The repeater can easily be upgraded to a Fiber Optic Repeater by

adding a Fiber Optic Unit (FOU) or a Fiber Optic Node (FON). q Remote Control. All repeaters can be remote controlled either over a fixed wire-

line modem or a radio modem q Battery Back-Up (BBU) for either 25 or 50 Ah battery capacity q Door-switch to be connected to external alarm input q Operation and Maintenance System (OMS). System for managing multiple

repeaters in a network. Requires MS Windows NT 4.0 with Service Pack 6 or higher or MS Windows 2000 with Service Pack 2 or higher. - Single or Multiuser as options - Polling of repeater - Status interrogation - Remote configuration - Supervision of ongoing configurations of multiple repeaters - Automatic downloading of new software - Scheduling activities - Report generating - External connections over the most common IP protocols (TCP/IP, UDP,

Streamsocket) - High level of inbuilt security classes q Power Supply. Most repeaters can be equipped with following power suppliers:

q 230 VAC q 115 VAC q +24 VDC q +48 VDC

Page: 1 (7) File: BUC2002005_RevE.doc Date: 2002-09-06

Allgon Repeater Conformity

1. General The repeater program covers all major cellular standards (GSM, AMPS/TDMA, CDMA and WCDMA). The products are formed from generic design platforms with a high grade of modularity. Mechanical housing and all essential RF electronics for the function of a repeater are standardised. Components like duplex filters and RF SAW filters are frequency specific and adopted to the different cellular standards. These few components are classified as strategic ones and are carefully selected. 2.Declaration of conformity Environmental Allgon repeater products are designed in accordance with ETS300 019: Stationary use at non-weather protected locations, extended climatic tests. Repeater Institute Concerns ETS

Reference Institute reference

AR types SEMKO • Encapsulation test acc. to IP65 requirements

EN 60 529 9749086-03

AR types Packforsk • Humidity • Chock • Vibration

ETS 300 019-2-4, class T4.1E

7861

ALR types SEMKO • Encapsulation test acc. to IP65 requirements

EN 60 529 0012029-04

ALR types SEMKO • Encapsulation UL50/CAN/CSA/CSA-C22.2 No 94 NEMA Type 4

0012029-05

ALR types Packforsk • Humidity • Chock • Vibration

ETS 300 019-2-5, class T4.1E

C01686 (prel.)


Radio Transmission and reception Allgon repeaters are designed in accordance with ETS300 577, GSM05.05: Radio transmission and reception (GSM05.05) and ETS300 609-4, part 4. Europe - Radio Transmission and Reception ETS 300 609-4 (harmonized standard ETS301 502) - EMC emission and immunity ETS 300 342-3 (Harmonized standard ETS 301 489-7) - 3GPP TS25.106 (only applicable on AR65XX models) Allgon Products Accredited Laboratory reference AR1100/004 CS, 230 V, GSM AR1100/004 CS, 230 V, GSM AR1100/002 CS 24/48 VDC, GSM AR1112/104 COMB, 230 V, GSM AR1100/004 CS, 230 V, Opto, GSM AR2100/004 CS, 230 V, DCS, PCN AR1100/002 CS, 230 V, GSM AR1100/904 CS, 230 V, EGSM AR2200/901 CS, 230 V, DCS,PCN AR1111/008 CS 230 V, GSM900 AR6500/001 CS, 230 V, WCDMA AR1100/804, CS,230 V, RGSM ALR2200/001, BS, 230 V, DCS, PCN ALR2200/901, BS, 230 V, DCS, PCN AR1200/052, BS, 230 V, DCS, PCN AR2100/004, CS, 230V, DCS, PCN

1381/008/95 1381/002/96 1381/004/96 1381/009/96 1381/014/97 1381/015/97 1381/016/97 1381/047/97 D000063K, 983911D 9951195R 200622 G127872H 0014109R 0014109R 9951194R 9951196R

US and Canada Relevant products fulfils the US emission requirements according to the Federal Communications Commission rule part 15, 22 and 90 and Industry of Canada specification RSS133 issue 1. Allgon Products FCC ref IC ref AR3100, CS, GSM 1900 AR3400, BS, DAMPS 1900 AR3500, SS, CDMA 1900 AR4200, BS, 800 MHz AR4200, BS, 800 MHz, New PA AR4500, SS, CDMA 800 MHz AR4540, SS, CDMA800 HP AR4600, BS, 800 MHz ALR4200, BS, 800 MHz, Compact ALR4600, BS, 800 MHz, iDEN, Compact

L6GAR3100 L6GAR3400 L6GAR3500 L6GAR4200 L6GAR4200A L6GAR4500 L6GAR4540 L6GAR4600 L6GALR4200 L6GALR4600

2869331142A 2869331138A 2869331135A 2869311169A 2869311209A 2869311191A 2869311237A 2869311189A 2869311227A 2869311226A


CS= Channel selective, BS= Band selective, SS= Segment selective, COMBI= Combinations of CS, BS and CS


EMC Standards Allgon repeaters are designed to meet European EMC Directive 89/336/EEC. Standards for Electrical equipment for Train and Marine are also fulfilled. Repeater Concerns Standard Reference ALR types

Immunity – Generic standard Emission – Generic standard EMC for radio equipment BTS and repeaters BTS systems equip. repeaters Railway applications, Rolling app. Immunity to cond. disturbance Maritime nav. and radio equip. EMC Marine equip. and installations ERM/EMC GSM base stations BTS systems equip. repeaters Limits and methods of measuring EMC for radio equipment Harmonic current emissions Voltage fluctuations and flicker Electrostatic discharge requirement Radiated electromagnetic field Burst Surge Conducted disturbance Voltage dips, interrupts and variation BTS and repeaters Electrostatic discharge requirement Radiated electromagnetic field Burst Surge Conducted disturbance Voltage dips, interrupts and variation Radio freq. electromagnetic field Maritime nav. and radio equip. EMC Marine equip. and installations

EN 61000-6-2 EN 61000-6-3 ETS 301 489-1 ETS 300 342-3 ETS 300 609-4 EN 50121-3-2 EN 61000-4-6 EN 60945 BS 1597 ETS 301 489-8 ETS 300 609-4 EN 55022 ETS 301 489-1 EN 61000-3-2 EN 61000-3-3 EN 61000-4-2 EN 61000-4-3 EN 61000-4-4 EN 61000-4-5 EN 61000-4-6 EN 61000-4-11 ETS 300 342-3 EN 61000-4-2 EN 61000-4-3 EN 61000-4-4 EN 61000-4-5 EN 61000-4-6 EN 61000-4-11 EN 50204 EN 60945 BS 7027

200435-1 200435-2 200217-4 200217-2 0145117D 0014109D E014-TR 020094

AR types Immunity – Generic standard Emission – Generic standard EMC for radio equipment BTS and repeaters BTS systems equip. repeaters

EN 61000-6-2 EN 61000-6-3 ETS 301 489-1 ETS 300 342-3 ETS 300 609-4

200433-1


Harmonic current emissions Voltage fluctuations and flicker Electrostatic discharge requirement Radiated electromagnetic field Burst Surge Conducted disturbance Power freq. magnetic field Voltage dips, interrupts and variation Immunity – Generic standard Emission – Generic standard EMC for radio equipment BTS and repeaters BTS systems equip. repeaters Harmonic current emissions Voltage fluctuations and flicker Electrostatic discharge requirement Radiated electromagnetic field Burst Surge Conducted disturbance Power freq. magnetic field Voltage dips, interrupts and variation Maritime nav. and radio equip. EMC Marine equip. and installations Maritime nav. and radio equip. EMC Marine equip. and installations

EN 61000-3-2 EN 61000-3-3 EN 61000-4-2 EN 61000-4-3 EN 61000-4-4 EN 61000-4-5 EN 61000-4-6 EN 61000-4-8 EN 61000-4-11 EN 61000-6-2 EN 61000-6-3 ETS 301 489-1 ETS 300 342-3 ETS 300 609-4 EN 61000-3-2 EN 61000-3-3 EN 61000-4-2 EN 61000-4-3 EN 61000-4-4 EN 61000-4-5 EN 61000-4-6 EN 61000-4-8 EN 61000-4-11 EN 60945 BS 1597 EN 60945 BS 7027

200434-1 200217-1 E014-TR 020095

DAS types Limits and methods of measuring Immunity – Generic standard Emission – Generic standard EMC for radio equipment BTS and repeaters BTS systems equip. repeaters Railway applications, Rolling app. Immunity to cond. disturbance Maritime nav. and radio equip. EMC Marine equip. and installations ERM/EMC GSM base stations BTS systems equip. repeaters

EN 55022 EN 61000-6-2 EN 61000-6-3 ETS 301 489-1 ETS 300 342-3 ETS 300 609-4 EN 50121-3-2 EN 61000-4-6 EN 60945 BS 1597 ETS 301 489-8 ETS 300 609-4

200436-1 200435-1 200435-2 200217-4 200217-2 0145117D


Limits and methods of measuring EMC for radio equipment Harmonic current emissions Voltage fluctuations and flicker Electrostatic discharge requirement Radiated electromagnetic field Burst Surge Conducted disturbance Voltage dips, interrupts and variation BTS and repeaters Electrostatic discharge requirement Radiated electromagnetic field Burst Surge Conducted disturbance Voltage dips, interrupts and variation Radio freq. electromagnetic field Maritime nav. and radio equip. EMC Marine equip. and installations

EN 55022 ETS 301 489-1 EN 61000-3-2 EN 61000-3-3 EN 61000-4-2 EN 61000-4-3 EN 61000-4-4 EN 61000-4-5 EN 61000-4-6 EN 61000-4-11 ETS 300 342-3 EN 61000-4-2 EN 61000-4-3 EN 61000-4-4 EN 61000-4-5 EN 61000-4-6 EN 61000-4-11 EN 50204 EN 60945 BS 7027

0014109D E014-TR 020094

Fibre Optic Transceiver The Fibre Optic Transceiver (FOT/FON) is to be regarded as a sub-assembly and is solely designed to fit Allgon repeater related products and consequently not allowed to be use in other kind of stand-alone applications. The FOT/FON is working with light in 1,3µm and 1,5µm wavelengths and can be integrated in any kind of Allgon repeater related products without affecting the radio performances. Safety The Allgon Fibre Optic Transceivers (FOT/FON) are classified as “CLASS 1 LASER PRODUCT” under the condition that they are integrated in any type of enclosure. Verification notice: - IEC/EN 60 825-1 Radiation safety of laser products for Europe and Canada - IEC/EN 60950 2:nd edition Safety of Information Technology Equipment, including Electrical Business Equipment. - US Food and Drug Administration requirements, part 1040.10, 1998 EMC The Allgon Fibre Optic Transceiver complies with EMC Directive 89/336/EEC and been tested in accordance with ETS300 342-3.


Repeater safety - IEC Publication 65 - ETL recognition according to UL 1950 3:rd Edition and CAN/CSA C22.2 950-95: Repeater type Listing Mark

ETL AR31xx 2002761 AR34xx 2002761 AR35xx 2002761 AR42xx 2002761 AR45xx 2002761 AR46xx 2002761 ALR32xx 2002761 ALR42xx 2002761


Kjell Knuutinen

Dattum/Date

2003-05-14

Godkänd/Approved

Dok nr/Doc no

SA102 54/1-201

Rev

R3A

Sida/Page


Fil/file

SA102 54-1-201_R3A.doc

Operation and Maintenance System

OMS version R3 Single User or Multi User system for Operation & Maintenance of all Allgon repeaters, WRH and Fiber Optic Nodes. Hardware and software requirements The hardware requirements vary depending on if the computer will be used as a server machine or as a client.

Server:

- Intel Pentium II based computer, running at a minimum of 600 MHz

- 256 MB RAM, 512 MB RAM recommended

- 2 GB available disk space

- Monitor capable of displaying a resolution of 1024 x 768 (1280 x 1024 recommended)

- Network card and TCP/IP protocol installed

- Windows NT4 with service pack 6 or higher, Windows 2000 with service pack 2 or higher

Client:

- Intel Pentium based computer, running at a minimum of 266 MHz

- 128 MB RAM, 256 MB RAM recommended

- 600 MB available disk space

- Monitor capable of displaying a resolution of 1024 x 768 (1280 x 1024 recommended)

- Network card and TCP/IP protocol installed

- Windows NT4 with service pack 6 or higher, Windows 2000 with service pack 2 or higher

- At least one serial communication port. (Multiport serial port board (DigiPort or compatible) is strongly recommended.)

- Hayes compatible modems (minimum 9600 bps) for serial ports. See the Modem Init Strings section for further information about compatible modems.

- One telephone line or mobile phone for each modem. If callback will be used, then each telephone line must have its own designated telephone number.


Kjell Knuutinen

Dattum/Date

2003-05-14

Godkänd/Approved

Dok nr/Doc no

SA102 54/1-201

Rev

R3A

Sida/Page


Fil/file

SA102 54-1-201_R3A.doc

Function and Features Multi-user System - Several users with separate security and configuration profiles can share the same database - Databases from Oracle Corporation with high level of security, performance and reliability Multi-modem - Up to 128 modems can be used simultaneous Alarm handling - Alarms are graphically displayed - Logged alarms can be sorted in any order Multimedia Concept - User defined colour setting of alarm and activity levels - Alarm sound can be played External Alarm transfer - SNMP - Nokia NMS - TCP/IP - ASCII Traffic statistics - Querying traffic statistics for the last week - Report for 7 days displayed per hour or per 15 minutes periods - Graph presenting RSSI percentage value over a peak and mean average time scale - Export all information to a Microsoft Excel file - Storage time settable from 1 to 1000 days Repeater activities - Directly executed - Scheduled executed any time or recurrent - Status shows all activities in progress and COM ports used User and Client Management - Repeater Manager shows a map over a number of regions, cells and repeaters - User Manager contains all the user privileges - Workstation manager for OMS client organisation


Kjell Knuutinen

Dattum/Date

2003-05-14

Godkänd/Approved

Dok nr/Doc no

SA102 54/1-201

Rev

R3A

Sida/Page


Fil/file

SA102 54-1-201_R3A.doc

Internal Mail System - Users in the OMS can communicate with each other - Individual or groups - Anyone to everyone event update Channel plan import - MSI Planet version V2.7/2.8 Data Export - Enabling export of database to a number of databases Templates - Efficient configurations - Template profile includes all repeater parameter settings Reports - OMS database incl. repeater configuration, user preferences and logs - Printed out, displayed or saved Help - On-line assistance - User’s Manual


Kjell KnuutinenDattum/Date

2001-01-05Godkänd/Approved Dok nr/Doc no

K118-201Rev

R1BSida/Page

1Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

K118-201_R1B

Specification of Allgon Fibre Optic TransceiverPart of FOU001

The specification is valid for:K118/1 Fibre Optic Transceiver, 1310 nm optical wavelengthK118/2 Fibre Optic Transceiver, 1550 nm optical wavelength

1. Electrical specification

Common Bandwidth @ 3 dB 1 800 - 2200 MHz Flatness 800 - 1000 MHz ± 2 dB Flatness 1700 - 2000 MHz ± 2 dB Input third order interception point > 50 dBm Input impedance 50 Ohm VSWR < 2 - Supply voltage + 7 V Power consumption, total < 3,5 W Transmitter RIN -155 dB/Hz Laser optic wavelength DFB 1310 or 1550 nm Max continuos RF input + 36 dBm Optical output power + 3 dBm Optic return loss > 55 dB RF attenuation settable by SW in 1 dB steps 2 0 - 20 dB Receiver Optic wavelength 1250 – 1600 nm Max optic power input + 5 dBm RF attenuation settable by SW in 1 dB steps 2 0 - 20 dB Alarm threshold level, warning < - 12 dBm Alarm threshold level, error < - 15 dBm Optic return loss > 55 dB Noise power output at max gain, no fibre connected < -135 dBm/Hz

5. Mechanical specification Dimensions. (W x H x D) 230 x 25 x 115 mm Weight 0,66 Lbs 0,3 kg Optical fibre 9/125 Single mode RF connectors SMA Optical connectors FC-APC, DIN-APC Others available Software interface RS232 9 pin D-sub

1 The Fibre Optic Transceiver is connected to a duplexfilter thus limiting useful bandwidth to cellular standard in use.2 RF to RF system link gain is settable from –55 to –15 dB with 1 meter fibre jumper


Kjell KnuutinenDattum/Date

2001-01-05Godkänd/Approved Dok nr/Doc no

K118-201Rev

R1BSida/Page

2Dok namn/Doc name

PRODUCT SPECIFICATIONFil/file

K118-201_R1B

4. Environmental specification Temperature range -4 to + 167 °F -20 to + 75 °C

5. OperationThe Fibre Optic Transceiver (FOT) is to be regarded as a modular component and is solely designed tofit Allgon repeaters and Base Station master Units and consequently not possible to use in other stand-alone applications. The FOT is a generic product for all types of Allgon repeaters.

6. Hardware & Software requirementsThe FOT is controlled by specific Fibre Optic Operation Terminal (FOOT) software requiring at least:- 486 desktop or notebook- Windows 95, 98 or NT version 4.0 or higher

7. AlarmsA summery alarm is generated by the FOT. The alarm connection is of an open collector type, open innormal mode and closed upon a failure.The summery alarm includes following individual alarms (accessible from FOOT software)- Laser failure (Tx)- No optic power received (Rx)- Temperature- Internal voltage

8. Declaration of conformity- Environmental specification ETS300 019-2-4- EMC emission and immunity ETS300 342-3- Electrical safety IEC/EN 60825-1

IEC/EN 60950




Dok nr/Doc no

K129/1_201 Rev

R1B Sida/Page


Fil/file

K129-201_R1B.doc

Specification of Allgon Fibre Optic Node

Part of FOU Product Number: K129/1

The specification is valid for: K129/1 Fibre Optic Node, 1310 nm optical wavelength K129/2 Fibre Optic Node, 1550 nm optical wavelength 1. Electrical specification

Common Bandwidth @ 3 dB 1 800 - 2200 MHz Flatness 800 - 1000 MHz ± 2 dB Flatness 1700 - 2200 MHz ± 2 dB Input third order interception point > 50 dBm Input impedance 50 Ohm VSWR < 2 - Supply voltage + 7 V Power consumption, total < 5 W Transmitter RIN -155 dBc/Hz Laser optic wavelength DFB 1310 or 1550 nm Max continuos RF input + 36 dBm Min. optical output power, two levels + 3/0 dBm Optic return loss > 55 dB RF attenuation settable by SW in 1 dB steps 2 0 - 20 dB Receiver Optic wavelength 1250 – 1600 nm Max optic power input + 5 dBm Low power output -15 dB RF attenuation settable by SW in 1 dB steps 2 0 - 20 dB Alarm threshold level, settable warning 0 to - 40 dBm Alarm threshold level, settable error 0 to - 40 dBm Optic return loss > 55 dB Noise power output at max gain, no fibre connected < -135 dBm/Hz 5. Mechanical specification Dimensions. (W x H x D) 310x85x40 mm Weight 0,88 Lbs 0,4 kg

1 The Fibre Optic Node is connected to a duplexfilter thus limiting useful bandwidth to cellular standard in use. 2 RF to RF system link gain is settable from –60 to –20 dB with 1 meter fibre jumper




Dok nr/Doc no

K129/1_201 Rev

R1B Sida/Page


Fil/file

K129-201_R1B.doc

Optical fibre 9/125 Single mode RF connectors SMA Optical connectors FC-APC, DIN-APC Others available Software interface RS232 9 pin D-sub 4. Environmental specification Temperature range -4 to + 167 °F -20 to + 75 °C 5. Operation The Fibre Optic Node (FON) is to be regarded as a modular component and is solely designed to fit Allgon repeaters and Base Station master Units and consequently not possible to use in other stand-alone applications. The FON is a generic product for all types of Allgon repeaters. 5,5. New Features • Built-in input power meter (optic meter) • Optical output power, software controlled, two levels • IP addressing • Settable alarm thresholds (two levels) • Sub carrier for data communication • Battery Back-up with charger • External alarm inputs with settable levels and polarity • R2R interface • RCC support • Remote software download 6. Hardware & Software The FON is locally/remotely controlled by standard Allgon Operation & Maintenance Terminal Software (OMT) and Operation & Management System (OMS). 7. Alarms The FON supervision and alarm handling is built identical to our repeater products, e.g. fully compatible with OMT and OMS. Following alarms are given from FON: - Laser failure (Tx) - No optic power received (Rx) - Temperature - Internal voltage - Sub carrier link supervision - External alarm 8. Declaration of conformity - Environmental specification ETS300 019-2-4 - EMC emission and immunity ETS300 342-3 - Electrical safety IEC/EN 60825-1 IEC/EN 60950

Standard 900 MHz EGSM Channel Selective

Product Description AR1100_902 2 Channel AR1100_904 4 Channel AR1111_906 6 Channel AR1111_908 8 Channel

Standard 900 MHz RGSM Channel Selective

Product Description AR1100_802 2 Channel AR1100_804 4 Channel

Standard 900 MHz EGSM Band Selective

Product Description

AR1200_952 16,5 MHz BW




Dok nr/Doc no

AR1200/952-201 Rev

F Sida/Page


Fil/file

AR1200_952_F.doc

STANDARD Band selective Repeater EGSM 900 MHz, 16,9 MHz BW Product Number: AR1200/952

1. Electrical specification (typical values) The repeater complies with the requirements of ETS 300 609-4 Frequency band Up link 880 - 915 MHz Frequency band Down link 925 - 960 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation -25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-16.9 MHz Filter setting resolution 25 kHz Automatic gain control Implemented Selectivity BW 3dB 16.9 MHz Selectivity BW 45dB BW 3dB + 1.2 MHz Selectivity BW 50dB BW 3dB + 2.2 MHz Pass band ripple 6 dB Output power, PEP +29 dBm Output power 2 carrier +23 dBm/carrier Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 160 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female Note! Approx. 1 dB more Pass band ripple when EGSM+GSM band is utilized.




Dok nr/Doc no

AR1100/902-201 Rev

B Sida/Page


Fil/file

AR1100_902_B.doc

Specification of a EGSM 900 channel selective repeater




<± 200 ns





Dok nr/Doc no

AR1100/904-201 Rev

B Sida/Page


Fil/file

AR1100_904_B.doc

Specification of a EGSM 900 channel selective repeater




<± 200 ns





Dok nr/Doc no

AR1111/906-201 Rev

B Sida/Page


Fil/file

AR1111_906_B.doc

Specification of an EGSM 900 channel selective repeater 6-channel version




<± 200 ns

Output power per channel +27 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1 MHz < -50 dB Selectivity ± 5 MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 230 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female Lock type ABLOY




Dok nr/Doc no

AR1111/908-201 Rev

A Sida/Page


Fil/file

AR1111_908_B.doc

Specification of a EGSM 900 channel selective repeater 8-channel version

Product Number: AR1111/908 1. Electrical specification (typical values) The repeater complies with the requirements of ETS 300 609-4


<± 200 ns

Output power per channel +27 dBm Automatic gain control Implemented Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1 MHz < -50 dB Selectivity ± 5 MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 305 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 3.Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female

Compact Dual Band

Product Description ALR1212_001 BS900/BS900 15 MHz BW ALR1212_002 BS900/BS900 25 MHz BW ALR1212_901 BS900/E-GSM 15 MHz BW ALR2212_001 BS1800/BS900 LB 15 MHz BW ALR2212_901 BS1800/BS900 UB 15 MHz BW ALR2222_001 BS1800/BS1800 LB 15 MHz BW ALR2222_095 BS1800/BS1800 LB/UB 15 MHz BW ALR2222_501 BS1800/BS1800 LB 25/15 MHz BW ALR2222_901 BS1800/BS1800 UB 15 MHz BW ALR3232_001 BS1900/BS1900 LB 15 MHz BW ALR3232_901 BS1900/BS1900 UB 15 MHz BW ALR3242_001 BS1900/BS800 LB 15 MHz BW ALR4242_002 BS800/BS800 15 MHz BW


Kjell Knuutinen

Dattum/Date

2003-07-18

Godkänd/Approved

Dok nr/Doc no

ALR1212/001-201 Rev

D Sida/Page


Fil/file

ALR1212-001_D.doc

COMPACT repeater with adjustable bandwidth 900/900 MHz version

Product Number: ALR1212/001 1. Electrical specification (typical values) GSM900 Bottom

The repeater complies with the requirements of ETS 300 609-4

Frequency tuning band Up link 890 – 915 MHz Frequency tuning band Down link 935 – 960 MHz Filter bandwidth standard, adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP* + 22 dBm Output power, 2 carrier* + 16 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 V AC Power consumption < 55 W


Kjell Knuutinen

Dattum/Date

2003-07-18

Godkänd/Approved

Dok nr/Doc no

ALR1212/001-201 Rev

D Sida/Page


Fil/file

ALR1212-001_D.doc

2. Electrical specification (typical values) GSM900 Door The repeater complies with the requirements of ETS 300 609-4


3. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class NEMA4/IP65 4. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 6.3 Inches 385 x 385 x 159,5 mm Mechanical outline See Compact High Weight < 44 lbs < 20 kg RF connectors N-type female Lock type Allgon Safety bolts *Hybrid combiner makes -3 dB less output power .


Kjell Knuutinen

Dattum/Date

2003-07-18

Godkänd/Approved

Dok nr/Doc no

ALR1212/002-201 Rev

D Sida/Page


Fil/file

ALR1212-002_D.doc

COMPACT repeater with adjustable bandwidth BS900/BS900 25 MHz BW

Product Number: ALR1212/002 1. Electrical specification (typical values) GSM900 Bottom

The repeater complies with the requirements of ETS 300 609-4



Kjell Knuutinen

Dattum/Date

2003-07-18

Godkänd/Approved

Dok nr/Doc no

ALR1212/002-201 Rev

D Sida/Page


Fil/file

ALR1212-002_D.doc



3. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class NEMA4/IP65 4. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 6.3 Inches 385 x 385 x 159,5 mm Mechanical outline See Compact High Weight < 44 lbs < 20 kg RF connectors N-type female Lock type Allgon Safety bolts *Hybrid combiner makes -3 dB less output power


Kjell Knuutinen

Dattum/Date

2003-06-12

Godkänd/Approved

Dok nr/Doc no

ALR1212/901-201

Rev

E

Sida/Page


Fil/file

ALR1212-901_E.doc


900 GSM/E-GSM Product Number: ALR1212/901

1. Electrical specification (typical values) 900 GSM The repeater complies with the requirements of ETS 300 609-4

Frequency tuning band Up link 890 – 915 MHz Frequency tuning band Down link 935 – 960 MHz Filter bandwidth standard, adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 45-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset > 20 dB Filter sensitivity @ 600 kHz offset > 30 dB Filter sensitivity @ 1 MHz offset > 35 dB Output power, PEP > + 22 dBm Output power, 2 carrier + 16 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 65 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 V AC Power consumption < 55 W


Kjell Knuutinen

Dattum/Date

2003-06-12

Godkänd/Approved

Dok nr/Doc no

ALR1212/901-201

Rev

E

Sida/Page


Fil/file

ALR1212-901_E.doc

2. Electrical specification (typical values) 900 E-GSM The repeater complies with the requirements of ETS 300 609-4

Frequency tuning band Up link 880 – 905 MHz Frequency tuning band Down link 925 – 950 MHz Filter bandwidth standard, adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset > 20 dB Filter sensitivity @ 600 kHz offset > 30 dB Filter sensitivity @ 1 MHz offset > 35 dB Output power, PEP + 22 dBm Output power, 2 carrier + 16 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption <55 W

3. Environmental specification Temperature range -13 to + 131 °F Temperature range -25 to + 55 °C Casing class NEMA4/IP65 4. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 6.3 Inches 385 x 385 x 159.5 mm Mechanical outline See Compact High Weight < 44 lbs < 20 kg RF-connectors N-type female Lock type Allgon Safety bolts


Kjell Knuutinen

Dattum/Date

2003-06-12

Godkänd/Approved

Dok nr/Doc no

ALR2212/001-201

Rev

C

Sida/Page


Fil/file

ALR2212-001_C.doc


1800/900 MHz version, Low band Product Number: ALR2212/001

1. Electrical specification (typical values) 1800 MHz Low Band The repeater complies with the requirement of ETS 300 609-4

Frequency tuning band Up link 1710 – 1765 MHz Frequency tuning band Down link 1805 – 1860 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 95 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55°C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 26 dBm Output power, 2 carrier + 20 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W


Kjell Knuutinen

Dattum/Date

2003-06-12

Godkänd/Approved

Dok nr/Doc no

ALR2212/001-201

Rev

C

Sida/Page


Fil/file

ALR2212-001_C.doc

2. Electrical specification (typical values) 900 MHz The repeater complies with the requirements of ETS 300 609-4

Frequency tuning band Up link 890 – 915 MHz Frequency tuning band Down link 935 – 960 MHz Filter bandwidth standard, adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 45-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP > + 25 dBm Output power, 2 carrier + 19 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 65 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 V AC Power consumption 55 W

3. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class NEMA4/IP65 4. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 6.3 Inches 385 x 385 x 159,5 mm Mechanical outline See Compact High Weight < 44 lbs < 20 kg RF connectors N-type female Lock type Allgon Safety bolts If common donor and service antennas are used, diplexers are installed in the repeater.

Approx. 1dB loss should be considered.


Kjell Knuutinen

Dattum/Date

2003-06-12

Godkänd/Approved

Dok nr/Doc no

ALR2212/901-201

Rev

C

Sida/Page


Fil/file

ALR2212-901_C.doc


1800/900 MHz version, High band Product Number: ALR2212/901

1. Electrical specification (typical values) 1800 MHz High Band The repeater complies with the requirement of ETS 300609-4

Frequency tuning band Up link 1730 – 1785 MHz Frequency tuning band Down link 1825 – 1880 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 95 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset > 20 dB Filter sensitivity @ 600 kHz offset > 30 dB Filter sensitivity @ 1 MHz offset > 35 dB Output power, PEP + 26 dBm Output power, 2 carrier + 20 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption <55 W


Kjell Knuutinen

Dattum/Date

2003-06-12

Godkänd/Approved

Dok nr/Doc no

ALR2212/901-201

Rev

C

Sida/Page


Fil/file

ALR2212-901_C.doc

2. Electrical specification (typical values) 900 MHz The repeater complies with the requirements of ETS 300 609-4

Frequency tuning band Up link 890 – 915 MHz Frequency tuning band Down link 935 – 960 MHz Filter bandwidth standard, adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 45-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset > 20 dB Filter sensitivity @ 600 kHz offset > 30 dB Filter sensitivity @ 1 MHz offset > 35 dB Output power, PEP > + 25 dBm Output power, 2 carrier + 19 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 65 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 V AC Power consumption <55 W

3. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class NEMA4/IP65 4. Mechanical specification Dimensions. (W x H x D) 15,2 x 15,2 x 6,3 Inches 385 x 385 x 159,5 mm Mechanical outline See Compact High Weight < 44 lbs < 20 kg RF-connectors N-type female Lock type Allgon Safety bolts


Kjell Knuutinen

Dattum/Date

2003-07-18

Godkänd/Approved

Dok nr/Doc no

ALR2222/095-201 Rev

D Sida/Page


Fil/file

ALR2222-095_D.doc


1800 MHz version, Low band/High band, Dual cell Product Number ALR2222/095

Band 1 (Low Band) 1. Electrical specification (typical values) The repeater complies with the requirement of ETS 300609-4

Frequency tuning band Up link 1710 – 1765 MHz Frequency tuning band Down link 1805 – 1860 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 95 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset 20 dB Filter sensitivity @ 600 kHz offset 30 dB Filter sensitivity @ 1 MHz offset 35 dB Output power, PEP* + 23 dBm Output power, 2 carrier* + 17 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power consumption 55 W Power supply voltage 85 - 265 VAC


Kjell Knuutinen

Dattum/Date

2003-07-18

Godkänd/Approved

Dok nr/Doc no

ALR2222/095-201 Rev

D Sida/Page


Fil/file

ALR2222-095_D.doc

Band 2 (High Band)

2. Electrical specification (typical values) The repeater complies with the requirement of ETS 300609-4

Frequency tuning band Up link 1730 – 1785 MHz Frequency tuning band Down link 1825 – 1880 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 95 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset 20 dB Filter sensitivity @ 600 kHz offset 30 dB Filter sensitivity @ 1 MHz offset 35 dB Output power, PEP* + 23 dBm Output power, 2 carrier* + 17 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W

3. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class NEMA4/IP65 4. Mechanical specification Dimensions. (W x H x D) 15,2 x 15,2 x 6,3 Inches 385 x 385 x 159,5 mm Mechanical outline See Compact High Weight < 44 lbs < 20 kg RF-connectors N-type female Lock type Allgon Safety bolts * Hybrid combiner makes -3 dB less output power


Kjell Knuutinen

Dattum/Date

2003-06-12

Godkänd/Approved

Dok nr/Doc no

ALR2222/095-201

Rev

C

Sida/Page


Fil/file

ALR2222-095_C.doc


1800 MHz version, Low band/High band, Dual cell Product Number ALR2222/095

Band 1 (Low Band) 1. Electrical specification (typical values) The repeater complies with the requirement of ETS 300609-4

Frequency tuning band Up link 1710 – 1765 MHz Frequency tuning band Down link 1805 – 1860 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 95 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset 20 dB Filter sensitivity @ 600 kHz offset 30 dB Filter sensitivity @ 1 MHz offset 35 dB Output power, PEP + 20 dBm Output power, 2 carrier + 14 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power consumption 55 W Power supply voltage 85 - 265 VAC


Kjell Knuutinen

Dattum/Date

2003-06-12

Godkänd/Approved

Dok nr/Doc no

ALR2222/095-201

Rev

C

Sida/Page


Fil/file

ALR2222-095_C.doc

Band 2 (High Band) 2. Electrical specification (typical values) The repeater complies with the requirement of ETS 300609-4

Frequency tuning band Up link 1730 – 1785 MHz Frequency tuning band Down link 1825 – 1880 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 95 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset 20 dB Filter sensitivity @ 600 kHz offset 30 dB Filter sensitivity @ 1 MHz offset 35 dB Output power, PEP + 20 dBm Output power, 2 carrier + 14 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W

3. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class NEMA4/IP65 4. Mechanical specification Dimensions. (W x H x D) 15,2 x 15,2 x 6,3 Inches 385 x 385 x 159,5 mm Mechanical outline See Compact High Weight < 44 lbs < 20 kg RF-connectors N-type female Lock type Allgon Safety bolts Note! -3 dB less output power according to combined antennas, 1 service and 1 donor antenna


Kjell Knuutinen

Dattum/Date

2003-06-12

Godkänd/Approved

Dok nr/Doc no

ALR2222/901-201

Rev

C

Sida/Page


Fil/file

ALR2222-901_C.doc


1800 MHz version, High band, Dual band Product Number ALR2222/901

Band 1 1. Electrical specification (typical values) The repeater complies with the requirement of ETS 300609-4

Frequency tuning band Up link 1730 – 1785 MHz Frequency tuning band Down link 1825 - 1880 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 95 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset 20 dB Filter sensitivity @ 600 kHz offset 30 dB Filter sensitivity @ 1 MHz offset 35 dB Output power, PEP + 23 dBm Output power, 2 carrier + 17 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power consumption 55 W Power supply voltage 85 - 265 VAC


Kjell Knuutinen

Dattum/Date

2003-06-12

Godkänd/Approved

Dok nr/Doc no

ALR2222/901-201

Rev

C

Sida/Page


Fil/file

ALR2222-901_C.doc

Band 2 2. Electrical specification (typical values) The repeater complies with the requirement of ETS 300609-4

Frequency tuning band Up link 1730 – 1785 MHz Frequency tuning band Down link 1825 – 1880 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 95 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset 20 dB Filter sensitivity @ 600 kHz offset 30 dB Filter sensitivity @ 1 MHz offset 35 dB Output power, PEP + 23 dBm Output power, 2 carrier + 17 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption <55 W

3. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class NEMA4/IP65 4. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 6.3 Inches 385 x 385 x 159,5 mm Mechanical outline See Compact Low Weight < 44 lbs < 20 kg RF-connectors N-type female


Kjell Knuutinen

Dattum/Date

2003-07-18

Godkänd/Approved

Dok nr/Doc no

ALR3232/001-201 Rev

D Sida/Page


Fil/file

ALR3232-001_D.doc

COMPACT repeater Dual band with adjustable bandwidth


1. Electrical specification (typical values) 1900 Bottom The repeater complies with the requirements of FCC

Frequency tuning band Up link 1850 – 1890 MHz Frequency tuning band Down link 1930 – 1970 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 80 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 25 dBm Output power, 2 carrier + 19 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption <55 W


Kjell Knuutinen

Dattum/Date

2003-07-18

Godkänd/Approved

Dok nr/Doc no

ALR3232/001-201 Rev

D Sida/Page


Fil/file

ALR3232-001_D.doc

2. Electrical specification (typical values) 1900 Door The repeater complies with the requirements of FCC


3. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class NEMA4/IP65 4. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 6.3 Inches 385 x 385 x 159,5 mm Mechanical outline See Compact High Weight < 44 lbs < 20 kg RF-connectors N-type female Lock type Allgon Safety bolts *Hybrid combiner makes -3 dB less output power


Kjell Knuutinen

Dattum/Date

2003-07-18

Godkänd/Approved

Dok nr/Doc no

ALR3232/901-201 Rev

D Sida/Page


Fil/file

ALR3232-901_D.doc


1900/1900 MHz version, High band Product Number: ALR3232/901


Frequency tuning band Up link 1870 – 1910 MHz Frequency tuning band Down link 1950 – 1990 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 80 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP* + 25 dBm Output power, 2 carrier* + 19 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption <55 W


Kjell Knuutinen

Dattum/Date

2003-07-18

Godkänd/Approved

Dok nr/Doc no

ALR3232/901-201 Rev

D Sida/Page


Fil/file

ALR3232-901_D.doc


Frequency tuning band Up link 1870 – 1910 MHz Frequency tuning band Down link 1950 – 1990 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 80 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP* + 25 dBm Output power, 2 carrier* + 19 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption <55 W

3. Environmental specification Temperature range -13 to + 131 °F -25 to + 55 °C Casing class NEMA4/IP65 4. Mechanical specification Dimensions. (W x H x D) 15,2 x 15,2 x 6,3 Inches 385 x 385 x 159,5 mm Mechanical outline See Compact High Weight < 44 lbs < 20 kg RF-connectors N-type female Lock type Allgon Safety bolts *Hybrid combiner makes -3 dB less output power


Kjell Knuutinen

Dattum/Date

2003-07-18

Godkänd/Approved

Dok nr/Doc no

ALR3242/001-201 Rev

E Sida/Page


Fil/file

ALR3242-001_E.doc

COMPACT repeater Dual band with adjustable bandwidth


1. Electrical specification (typical values) 1900 Bottom The repeater complies with the requirements of FCC



Kjell Knuutinen

Dattum/Date

2003-07-18

Godkänd/Approved

Dok nr/Doc no

ALR3242/001-201 Rev

E Sida/Page


Fil/file

ALR3242-001_E.doc

2. Electrical specification (typical values) 800 Door The repeater complies with the requirements of FCC

Frequency tuning band Up link 824 – 849 MHz Frequency tuning band Down link 869 - 894 MHz Filter bandwidth standard, adjustable 0.5 – 19 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 28 dBm Output power, 2 carrier + 22 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 65 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption <55 W

3. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class NEMA4/IP65 4. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 6.3 Inches 385 x 385 x 159,5 mm Mechanical outline See Compact High Weight < 44 lbs < 20 kg RF-connectors N-type female Lock type Allgon Safety bolts If common donor and service antennas are used, diplexers are installed in the repeater.



Kjell Knuutinen

Dattum/Date

2003-07-18

Godkänd/Approved

Dok nr/Doc no

ALR4242/002-201 Rev

D Sida/Page


Fil/file

ALR4242-002_D.doc

COMPACT repeater with adjustable bandwidth Dual 800 MHz version, 25 MHz BW


1. Electrical specification (typical value) 800 Bottom The repeater complies with the requirements of FCC

Frequency tuning band Up link 824 – 849 MHz Frequency tuning band Down link 869 – 894 MHz Filter bandwidth standard, adjustable 0.5 – 25 MHz Filter setting resolution 12.5 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset > 20 dB Filter sensitivity @ 600 kHz offset > 30 dB Filter sensitivity @ 1 MHz offset > 35 dB Output power, PEP* + 25 dBm Output power, 2 carrier* + 19 dBm Band pass ripple 5 dB Max absolute group delay 6 µs Noise figure at 65 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 – 265 VAC Power consumption <55 W


Kjell Knuutinen

Dattum/Date

2003-07-18

Godkänd/Approved

Dok nr/Doc no

ALR4242/002-201 Rev

D Sida/Page


Fil/file

ALR4242-002_D.doc

2. Electrical specification (typical value) 800 Door The repeater complies with the requirements of FCC

Frequency tuning band Up link 824 – 849 MHz Frequency tuning band Down link 869 – 894 MHz Filter bandwidth standard, adjustable 0.5 – 25 MHz Filter setting resolution 12.5 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset > 20 dB Filter sensitivity @ 600 kHz offset > 30 dB Filter sensitivity @ 1 MHz offset > 35 dB Output power, PEP* + 25 dBm Output power, 2 carrier* + 19 dBm Band pass ripple 5 dB Max absolute group delay 6 µs Noise figure at 65 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 – 265 VAC Power consumption <55 W

3. Environmental specification Temperature range -13 to + 131 °F -25 to + 55 °C Casing class NEMA4/IP65 4. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 6.3 Inches 385 x 385 x 159,5 mm Mechanical outline See Compact High Weight < 44 lbs < 20 kg RF-connectors N-type female Lock type Allgon Safety bolts *Hybrid combiner makes -3 dB less output power

Standard Dual Band

Product Description AR1212_052 GSM900 BS/BS 16,5 MHz BW AR2111_024 GSM1800 2 CH/900 4 CH LB AR2111_042 GSM1800 4 CH/900 2 CH LB AR2111_924 GSM1800 2 CH/900 4 CH UB AR2111_942 GSM1800 4 CH/900 2 CH UB AR2122_021 GSM1800 2 CH/BS1800 16,5 MHz BW AR2212_052 GSM1800 BS/900 BS LB AR2212_952 GSM1800 BS/900 BS UB AR3131_022 GSM1900 2+2 CH LB AR3131_044 GSM1900 4+4 CH LB AR3131_922 GSM1900 2+2 CH UB AR3442_052 TDMA1900 BS/BS 800 16,5 MHz BW AR3442_053 TDMA1900 BS/BS 800 25 MHz BW AR3542_052 CDMA1900/BS800 AR4242_052 BS800/BS800 16,5 MHz BW




Dok nr/Doc no

AR1212/052-201 Rev

D Sida/Page


Fil/file

AR1212_052_D.doc

Specification of a Dual Band selective Repeater 900/900 MHz, 1 donor and 1 service antenna


1. Electrical specification (typical values) The repeater complies with the requirements of ETS 300 609-4 Frequency band Up link Bottom 890 - 915 MHz Frequency band Up link Door 890 - 915 MHz Frequency band Down link Bottom 935 - 960 MHz Frequency band Down link Door 935 - 960 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation -25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-16.9 MHz Filter setting resolution 25 kHz Automatic gain control Implemented Selectivity BW 3dB 16.9 MHz Selectivity BW 45dB BW 3dB + 1.2 MHz Selectivity BW 50dB BW 3dB + 2.2 MHz Pass band ripple 5 dB Output power, PEP +26 dBm Output power 2 carrier +20 dBm/carrier Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 160 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female 3 dB less output power due hybrid antenna ports.




Dok nr/Doc no

AR2111/024-201 Rev

B Sida/Page


Fil/file

AR2111_024_B.doc

Specification of a GSM 1800/900 channel selective repeater 2+4 -channel version, Lower band


• The antenna connections 2+4 channels can either be combined diplexer or separated 1. Electrical specification (typical values) GSM 1800 2 channels The repeater complies with the requirements of ETS 300609-4


<± 200 ns

Output power per channel +33 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 85 W




Dok nr/Doc no

AR2111/024-201 Rev

B Sida/Page


Fil/file

AR2111_024_B.doc

2. Electrical specification (typical values) GSM 900 4 channels The repeater complies with the requirements of ETS 300 609-4


<± 200 ns

Output power per channel +30 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1 MHz < -50 dB Selectivity ± 5 MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 155 W 3. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 4. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female If common donor and service antennas are used, diplexers are installed in the repeater.





Dok nr/Doc no

AR2111/042-201 Rev

B Sida/Page


Fil/file

AR2111_042_B.doc

Specification of a GSM 1800/900 channel selective repeater 4+2 -channel version, Lower band


• The antenna connections 4+2 channels can either be combined with diplexer or separated

1. Electrical specification (typical values) GSM 1800 4 channels The repeater complies with the requirements of ETS 300609-4


<± 200 ns

Output power per channel GSM 1800 +30 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 155 W




Dok nr/Doc no

AR2111/042-201 Rev

B Sida/Page


Fil/file

AR2111_042_B.doc



<± 200 ns

Output power per channel +33 dBm Automatic gain control Implemented Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1 MHz < -50 dB Selectivity ± 5 MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 85 W 3. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 4. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female If common donor and service antennas are used, diplexers are installed in the repeater.





Dok nr/Doc no

AR2111/924-201 Rev

B Sida/Page


Fil/file

AR2111_924_B.doc

Specification of a GSM 1800/900 channel selective repeater 2+4 -channel version, High band

Product Number: AR2111/924 • The antenna connections 2+4 channels can either be combined diplexer or separated



<± 200 ns





Dok nr/Doc no

AR2111/924-201 Rev

B Sida/Page


Fil/file

AR2111_924_B.doc



<± 200 ns

Output power per channel +30 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1 MHz < -50 dB Selectivity ± 5 MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 155 W 3. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 4. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female If common donor and service antennas are used, diplexers are installed in the repeater.





Dok nr/Doc no

AR2111/942-201 Rev

B Sida/Page


Fil/file

AR2111_942_B.doc

Specification of a GSM 1800/900 channel selective repeater 4+2 -channel version, High band


• The antenna connections 4+2 channels can either be combined with diplexer or separated



<± 200 ns





Dok nr/Doc no

AR2111/942-201 Rev

B Sida/Page


Fil/file

AR2111_942_B.doc



<± 200 ns

Output power per channel +33 dBm Automatic gain control Implemented Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1 MHz < -50 dB Selectivity ± 5 MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 85 W 3. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 4. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female If common donor and service antennas are used, diplexers are installed in the repeater.





Dok nr/Doc no

AR2122/021-201 Rev

C Sida/Page


Fil/file

AR2122_021_C.doc

Specification of a Channel/Band selective Repeater GSM1800 2 CH/BS1800 MHz, Lower band


1. Electrical specification (typical values) GSM 1800 2 CH The repeater complies with the requirements of ETS 300609-4


<± 200 ns





Dok nr/Doc no

AR2122/021-201 Rev

C Sida/Page


Fil/file

AR2122_021_C.doc

2. Electrical specification (typical values) GSM 1800 BS The repeater complies with the requirements of ETS 300 609-4

Frequency band Up link 1710 – 1765 MHz Frequency band Down link 1805 - 1860 MHz Duplex spacing 95 MHz Absolute group delay < 6 µs Antenna isolation supervision Continuously Filter bandwidth (remotely adjustable) 0.5 - 16.9 MHz Filter setting resolution 25 KHz Gain adjustment range (in 1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Selectivity BW 3 dB 16.9 MHz Selectivity BW 45 dB BW3 dB + 1.2 MHz Selectivity BW 50 dB BW3 dB + 2.2 MHz Pass band ripple 5 dB Output power, PEP + 29 dBm Output power 2 carrier + 23 dBm/carrier Automatic gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, max 160 W 3. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 4. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female If common donor and service antennas are used, -3 dB less output power




Dok nr/Doc no

AR2212/952/01_201 Rev

C Sida/Page


Fil/file

AR2212_952_C.doc

Specification of a Band Selective Repeater Dual band

1800 MHz/900 MHz High Band Product Number: AR2212/952

1. Electrical specification (typical values) 1800 MHz High Band Bottom The repeater complies with the requirements of ETS 300 609-4 Frequency band Up link 1730 - 1785 MHz Frequency band Down link 1825 – 1880 MHz Duplex spacing 95 MHz Absolute group delay < 6 µs Antenna isolation supervision Continuously Filter bandwidth (remotely adjustable) 0.5 - 16.9 MHz Filter setting resolution 25 KHz Gain adjustment range (in 1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C 6 dB Selectivity BW 3 dB 16.9 MHz Selectivity BW 45 dB BW3 dB + 1.2 MHz Selectivity BW 50 dB BW3 dB + 2.2 MHz Output power, PEP + 32 dBm Output power 2 carrier + 26 dBm/carrier Pass band ripple 6 dB Automatic gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage 230 V AC Power consumption, max 160 W




Dok nr/Doc no

AR2212/952/01_201 Rev

C Sida/Page


Fil/file

AR2212_952_C.doc

2. Electrical specification (typical values) 900 MHz Door The repeater complies with the requirements of ETS 300 609-4 Frequency band Up link 890 - 915 MHz Frequency band Down link 935 - 960 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation -25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-16.9 MHz Filter setting resolution 25 KHz Selectivity BW 3dB 16.9 MHz Selectivity BW 45dB BW 3dB + 1.2 MHz Selectivity BW 50dB BW 3dB + 2.2 MHz Output power, PEP +29 dBm Output power 2 carrier +23 dBm/carrier Pass band ripple 5 dB Automatic gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage 230 V AC Power consumption, max 160 W 3. Environmental specification Temperature range -13 to +131 °F -25 to + 55 °C Casing class IP65 4. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female If common donor and service antennas are used, diplexers are installed in the repeater.





Dok nr/Doc no

AR3131/022-201 Rev

B Sida/Page


Fil/file

AR3131_022_B.doc

Specification of a Dual GSM 1900 channel selective repeater 2+2 -channel version, Lower band


1. Electrical specification (typical values) GSM1900 Bottom The repeater complies with the requirements of ETS 300 609-4


<± 200 ns





Dok nr/Doc no

AR3131/022-201 Rev

B Sida/Page


Fil/file

AR3131_022_B.doc



<± 200 ns

Output power per channel +33 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 85 W 3. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 4.Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female If common donor and service antennas are used, -3 dB less output power




Dok nr/Doc no

AR3131/044-201 Rev

B Sida/Page


Fil/file

AR3131_044_B.doc

Specification of a Dual GSM 1900 channel selective repeater 4+4-channel version, Lower band




<± 200 ns





Dok nr/Doc no

AR3131/044-201 Rev

B Sida/Page


Fil/file

AR3131_044_B.doc



<± 200 ns

Output power per channel +30 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 155 W 3. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 4.Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female If common donor and service antennas are used, -3 dB less output power




Dok nr/Doc no

AR3131/922-201 Rev

B Sida/Page


Fil/file

AR3131_922_B.doc

Specification of a Dual GSM 1900 channel selective repeater 2+2-channel version, High band Product Number: AR3131/922



<± 200 ns





Dok nr/Doc no

AR3131/922-201 Rev

B Sida/Page


Fil/file

AR3131_922_B.doc



<± 200 ns

Output power per channel +33 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ± 100KHz > -3 dB Selectivity ± 400KHz < -35 dB Selectivity ± 600KHz < -45 dB Selectivity ± 1MHz < -50 dB Selectivity ± 5MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 85 W 3. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 4. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female If common donor and service antennas are used, -3 dB less output power




Dok nr/Doc no

AR3442/052-201 Rev

C Sida/Page


Fil/file

AR3442_052_C.doc


1900/800 MHz version, Lower band Product number: AR3442/052

1. Electrical specification (typical value) BS1900 The repeater complies with the FCC requirements

Frequency band Up link 1850 – 1890 MHz Frequency band Down link 1930 – 1970 MHz Duplex spacing 80 MHz Absolute group delay < 6 µs Antenna isolation supervision Continuously Filter bandwidth (remotely adjustable) 0.5 – 16.9 MHz Filter setting resolution 25 KHz Gain adjustment range (in 1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Selectivity BW 3 dB 16.9 MHz Selectivity BW 45 dB BW3 dB + 1.2 MHz Selectivity BW 50 dB BW3 dB + 2.2 MHz Passband ripple 6 dB Max output power PEP ? + 36 dBm Output power 2 carrier ? + 30 dBm Automat gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 160 W




Dok nr/Doc no

AR3442/052-201 Rev

C Sida/Page


Fil/file

AR3442_052_C.doc

2. Electrical specification (typical value) BS800 The repeater complies with the requirements of FCC Frequency band Up link 824 - 849 MHz Frequency band Down link 869 - 894 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-16.9 MHz Filter setting resolution 25 kHz Selectivity BW 3dB 16.9 MHz Selectivity BW 45dB BW 3dB + 1.2 MHz Selectivity BW 50dB BW 3dB + 2.2 MHz Pass band ripple 5 dB Output power, PEP ? +36 dBm Output power 2 carrier ? +30 dBm/carrier Automatic gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 160 W 3. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class NEMA4/IP65 4. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type Remark ? : If common donor and service antennas are used, diplexers are installed in the repeater.





Dok nr/Doc no

AR3442/053-201 Rev

B Sida/Page


Fil/file

AR3442_053_B.doc




Frequency band Up link 1850 – 1890 MHz Frequency band Down link 1930 – 1970 MHz Duplex spacing 80 MHz Absolute group delay < 6 µs Antenna isolation supervision Continuously Filter bandwidth (remotely adjustable) 0.5 – 16.5 MHz Filter setting resolution 25 KHz Gain adjustment range (in 1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Selectivity BW3 dB, 16.5 MHz filter 16.5 MHz Selectivity BW35 dB BW3 dB + 1.2 MHz Selectivity BW45 dB BW3 dB + 2.2 MHz Passband ripple 5 dB Max output power PEP ? + 36 dBm Output power 2 carrier ? + 30 dBm Automat gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 160 W




Dok nr/Doc no

AR3442/053-201 Rev

B Sida/Page


Fil/file

AR3442_053_B.doc

2. Electrical specification (typical value) BS800 The repeater complies with the requirements of FCC Frequency band Up link 824 - 849 MHz Frequency band Down link 869 - 894 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-25 MHz Filter setting resolution 25 kHz Selectivity BW 3dB 25 MHz Selectivity BW 35dB BW 3dB + 1.2 MHz Selectivity BW 45dB BW 3dB + 2.2 MHz Pass band ripple 5 dB Output power, PEP ? +36 dBm Output power 2 carrier ? +30 dBm/carrier Automatic gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 160 W 3. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class NEMA4/IP65 4. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors 7/16-type Remark ? : If common donor and service antennas are used, diplexers are installed in the repeater.





Dok nr/Doc no

AR3442/052-201 Rev

C Sida/Page


Fil/file

AR3442_052_C.doc




Frequency band Up link 1850 – 1890 MHz Frequency band Down link 1930 – 1970 MHz Duplex spacing 80 MHz Absolute group delay < 6 µs Antenna isolation supervision Continuously Filter bandwidth (remotely adjustable) 0.5 – 16.9 MHz Filter setting resolution 25 KHz Gain adjustment range (in 1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Selectivity BW 3 dB 16.9 MHz Selectivity BW 45 dB BW3 dB + 1.2 MHz Selectivity BW 50 dB BW3 dB + 2.2 MHz Passband ripple 6 dB Max output power PEP ? + 36 dBm Output power 2 carrier ? + 30 dBm Automat gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 160 W




Dok nr/Doc no

AR3442/052-201 Rev

C Sida/Page


Fil/file

AR3442_052_C.doc

2. Electrical specification (typical value) BS800 The repeater complies with the requirements of FCC Frequency band Up link 824 - 849 MHz Frequency band Down link 869 - 894 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-16.9 MHz Filter setting resolution 25 kHz Selectivity BW 3dB 16.9 MHz Selectivity BW 45dB BW 3dB + 1.2 MHz Selectivity BW 50dB BW 3dB + 2.2 MHz Pass band ripple 5 dB Output power, PEP ? +36 dBm Output power 2 carrier ? +30 dBm/carrier Automatic gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 160 W 3. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class NEMA4/IP65 4. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type Remark ? : If common donor and service antennas are used, diplexers are installed in the repeater.





Dok nr/Doc no

AR4242/052-201 Rev

C Sida/Page


Fil/file

AR4242_052_C.doc

Specification of a Dual Band selective Repeater 800/800 MHz

Product Number: AR4242/052 1. Electrical specification (typical value) BS800 Bottom The repeater complies with the requirements of FCC Frequency band Up link 824 - 849 MHz Frequency band Down link 869 - 894 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-16.9 MHz Filter setting resolution 25 kHz Selectivity BW 3dB 16.9 MHz Selectivity BW 45dB BW 3dB + 1.2 MHz Selectivity BW 50dB BW 3dB + 2.2 MHz Pass band ripple 5 dB Output power, PEP +36 dBm Output power 2 carrier +30 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 160 W




Dok nr/Doc no

AR4242/052-201 Rev

C Sida/Page


Fil/file

AR4242_052_C.doc

2. Electrical specification (typical value) BS800 Door The repeater complies with the requirements of FCC Frequency band Up link 824 - 849 MHz Frequency band Down link 869 - 894 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-16.9 MHz Filter setting resolution 25 kHz Selectivity BW 3dB 16.9 MHz Selectivity BW 45dB BW 3dB + 1.2 MHz Selectivity BW 50dB BW 3dB + 2.2 MHz Pass band ripple 5 dB Output power, PEP +36 dBm Output power 2 carrier +30 dBm/carrier Max out of band spurious emission -13 dBm Automatic gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 115 V AC Power consumption, max 160 W 3. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class IP65 4. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female If common donor and service antennas are used, -3 dB less output power.




Dok nr/Doc no

AR2212/052/01_201 Rev

C Sida/Page


Fil/file

AR2212_052_C.doc

Specification of a Band Selective Repeater Dual band

1800 MHz/900 MHz Low Band Product Number: AR2212/052

1. Electrical specification (typical values) 1800 MHz Low Band Bottom The repeater complies with the requirements of ETS 300 609-4 Frequency band Up link 1710 - 1765 MHz Frequency band Down link 1805 – 1860 MHz Duplex spacing 95 MHz Absolute group delay < 6 µs Antenna isolation supervision Continuously Filter bandwidth (remotely adjustable) 0.5 - 16.9 MHz Filter setting resolution 25 KHz Gain adjustment range (in 1 dB steps) 45-85 dB Gain (max variation –25 to +55 °C 6 dB Selectivity BW 3 dB 16.9 MHz Selectivity BW 45 dB BW3 dB + 1.2 MHz Selectivity BW 50 dB BW3 dB + 2.2 MHz Output power, PEP + 32 dBm Output power 2 carrier + 26 dBm/carrier Pass band ripple 6 dB Automatic gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage 230 V AC Power consumption, max 160 W




Dok nr/Doc no

AR2212/052/01_201 Rev

C Sida/Page


Fil/file

AR2212_052_C.doc

2. Electrical specification (typical values) 900 MHz Door The repeater complies with the requirements of ETS 300 609-4 Frequency band Up link 890 - 915 MHz Frequency band Down link 935 - 960 MHz Duplex spacing 45 MHz Absolute group delay < 6 µs Gain adjustment range (1 dB steps) 45-85 dB Gain (max variation -25 to +55 °C) 6 dB Antenna isolation supervision Continuously Filter band width (remotely adjustable) 0.5-16.9 MHz Filter setting resolution 25 KHz Selectivity BW 3dB 16.9 MHz Selectivity BW 45dB BW 3dB + 1.2 MHz Selectivity BW 50dB BW 3dB + 2.2 MHz Output power, PEP +29 dBm Output power 2 carrier +23 dBm/carrier Pass band ripple 5 dB Automatic gain control Implemented Noise figure at 85 dB gain, 25° C (typical) 6 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage 230 V AC Power consumption, max 160 W 3. Environmental specification Temperature range -13 to +131 °F -25 to + 55 °C Casing class IP65 4. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female If common donor and service antennas are used, diplexers are installed in the repeater.


WCDMA Standard / Compact

Product Description AR6500_001 1-2 Channel AR6560_002 1-2 Channel, High Power AR6565_022 3-4 Channel ALR6200_001 15 MHz Band selective Compact

Utfärdare/Issued by

Product Management Dattum/Date


SYKLK

Dok nr/Doc no

AR6500/001-201 Rev

K Sida/Page


Fil/file

AR6500_001_K.doc

Specification of a WCDMA channel selective repeater 1-2 channel version

Product Number: AR6500/001 1. Electrical specification (typical values) The repeater complies with the requirements of 3G TS 25.106 V4.1.0

Frequency band Up link 1920 -1980 MHz Frequency band Down link 2110 - 2170 MHz Duplex spacing 190 MHz Number of channels 1-2 Nominal channel spacing 5 MHz Channel frequency steps 200 kHz Channel band width @ -3 dB 4,4 MHz Automatic gain control Implemented Gain adjustment range (1 dB steps) 60-90 dB Absolute group delay <6 µs Output power (DL) RMS, one WCDMA carrier 1 +30 dBm Output power (DL) RMS, two WCDMA carrier 1 +25 dBm/carrier Output power (UL) RMS, one WCDMA carrier 1 +20 dBm Output power (UL) RMS, two WCDMA carrier 1 +15 dBm/carrier Spurious and Intermodulation 2 -30 dBm Pass band ripple within 4,0 MHz 2 dB Gain variation at 80 dB gain, over freq. band 4 dB Noise figure at max gain, 25° C 3 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB RF-connectors N-type female Power supply voltage 230 V AC Power consumption, max 160 W 1 Measured with test model 1/64 DPCH active channels 2 According to 3G TS 25.106 V4.1.0 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 F Humidity (relative) 95 % Casing class NEMA4/IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female




Dok nr/Doc no

AR6560_002-201 Rev

K Sida/Page


Fil/file

AR6560_002_K.doc

Specification of a WCDMA channel selective repeater 1-2 channel version, high power

Product number: AR6560/002 1. Electrical specification (typical values) The repeater complies with the requirements of 3G TS 25.106 V4.1.0 Frequency band Up link 1920 –1980 MHz Frequency band Down link 2110 – 2170 MHz Duplex spacing 190 MHz Number of channels 1-2 Nominal channel spacing 5 MHz Channel frequency steps 200 KHz Channel band width @ -3 dB 4,4 MHz Automatic gain control Implemented Gain adjustment range (1 dB steps) 65-95 dB Absolute group delay <6 µs Output power (DL) RMS, one WCDMA carrier 1 +38 dBm Output power (DL), RMS, two WCDMA carrier 1 +33 dBm/carrier Output power (UL), RMS, one WCDMA carrier 1 +20 dBm Output power (UL), RMS, two WCDMA carrier 1 +15 dBm/carrier Spurious and Intermodulation 2 -30 dBm Pass band ripple within 4,0 MHz 2 dB Gain variation at 80 dB gain, over freq. band 4 dB Noise figure at max gain, 25° C 3 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss (typical) 14 dB RF-connectors N-type female Power supply voltage 230 V AC Power consumption, max 320 W 1 Measured with test model 1/64 DPCH active channels at 61% clipping ratio fulfilling spectrum emission mask 2

According to 3G TS 25.106 V4.1.0 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 F Humidity (relative) 95 % Casing class NEMA4/IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 9.6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female


Product Management Dattum/Date


SYKLK Dok nr/Doc no

AR6565/022-201 Rev

I Sida/Page


Fil/file

AR6565_022_I.doc

Specification of a WCDMA channel selective repeater 2+2 channel version

Product Number: AR6565/022 ! True 2+2 CDMA channels in one package ! The antenna connections 2+2 channels can either be combined (3dB loss) or separated 1. Electrical specification (typical values) The repeater complies with the requirements of 3G TS 25.106 V4.0.0 Frequency band Up link 1920 -1980 MHz Frequency band Down link 2110 - 2170 MHz Duplex spacing 190 MHz Number of channels 3-4 Nominal channel spacing 5 MHz Channel frequency steps 200 kHz Channel band width @ -3 dB 4,4 MHz Automatic gain control Implemented Gain adjustment range (1 dB steps) 55-90 dB Absolute group delay <6 µs Output power ( DL) RMS, one WCDMA carrier 1 +30 dBm Output power ( DL) RMS, two WCDMA carrier 1 +25 dBm/carrier Output power ( UL) RMS, one WCDMA carrier 1 +20 dBm Output power ( UL) RMS, two WCDMA carrier 1 +15 dBm/carrier Spurious and Intermodulation 2 -30 dBm Pass band ripple within 4,0 MHz 2 dB Gain variation at 80 dB gain, over freq. band 4 dB Noise figure at max gain, 25° C 3 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB RF-connectors N-type female Power supply voltage (default) 230 V AC Power consumption, max 320 W 1 Measured with test model 1/64 DPCH active channels 2According to 3G TS 25.106 V4.0.0

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 F Humidity (relative) 95 % Casing class NEMA4/IP65 MTBF 50000 Hours 3. Mechanical specification Dimensions. (W x H x D) 17,4 x 20,9 x 9,6 Inches 440 x 530 x 240 mm Mechanical outline See Standard High Weight 75 lbs 34 Kg RF connectors N-type female


Kjell Knuutinen

Dattum/Date

2004-02-05

Godkänd/Approved

Dok nr/Doc no

ALR6200-201 Rev

G Sida/Page


Fil/file

ALR6200_G.doc

Specification of a compact WCDMA band selective repeater 1-3 channel capacity

Product number: ALR6200/001 1. Electrical specification (typical values) The repeater complies with 3G TS 25.106 V4.1.0 requirements Frequency band Up link 1920 –1980 MHz Frequency band Down link 2110 – 2170 MHz Duplex spacing 190 MHz Filter bandwidth, software adjustable 5-15 MHz Number of carriers 1-3 Filter setting resolution 25 KHz Automatic gain control Implemented Gain adjustment range (1 dB steps) 55-70 dB Absolute group delay <6 µs Output power, RMS, DL +24 dBm Output power RMS, DL, two WCDMA carrier +19 dBm/carrier Output power RMS DL, three WCDMA carrier +18 dBm/carrier Output power, RMS, UL +20 dBm Output power RMS, UL, two WCDMA carrier +15 dBm/carrier Output power RMS UL, three WCDMA carrier +14 dBm/carrier Spurious and Intermodulation -30 dBm Pass band ripple in each WCDMA channel 3 dB Noise figure UL max gain, 25° C 3 dB Noise figure DL max gain, 25° C 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB RF-connectors N-type female Power supply voltage 85-260 VAC Power consumption, max 55 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class NEMA4/IP65 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 4.3 Inches 385 x 385 x 110 mm Mechanical outline See Compact Low Weight < 22 lbs < 10 kg RF-connectors N-type female Lock type Allgon Safety bolts

ALLGON SYSTEMS AB Utfärdare/Issued by



Dok nr/Doc no

AR1100/802-201 Rev

D Sida/Page


Fil/file

AR1100_802_D.doc

Specification of a RGSM 900 channel selective repeater 2-channel version



<± 200 ns

Max output power per channel +33 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ±100KHz > -3 dB Selectivity ±400KHz < -35 dB Selectivity ±600KHz < -45 dB Selectivity ±1 MHz < -50 dB Selectivity ±5 MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, typ. (max) 80 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female

ALLGON SYSTEMS AB Utfärdare/Issued by



Dok nr/Doc no

AR1100/804-201 Rev

D Sida/Page


Fil/file

AR1100_804_D.doc

Specification of a RGSM 900 channel selective repeater 4-channel version



<± 200 ns

Max output power per channel +30 dBm Automatic gain control Implemented Antenna isolation supervision Continuously Selectivity ±100KHz > -3 dB Selectivity ±400KHz < -35 dB Selectivity ±600KHz < -45 dB Selectivity ±1 MHz < -50 dB Selectivity ±5 MHz < -60 dB Pass band ripple 3 dB Noise figure at 85 dB gain, 25° C (typical) 5 dB Maximum input power (non-destructive) +13 dBm Receiver input port return loss 14 dB Power supply voltage (default) 230 V AC Power consumption, typ. (max) 120 W 2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight 46 lbs 21 Kg RF connectors N-type female


Kjell Knuutinen

Dattum/Date

2003-06-11

Godkänd/Approved

Dok nr/Doc no

ALR1200/901-201

Rev

F

Sida/Page


Fil/file

ALR1200-901_F.doc

COMPACT repeater with adjustable bandwidth 900 MHz version, EGSM, 15 MHz BW



Frequency tuning band Up link 880 – 915 MHz Frequency tuning band Down link 925 – 960 MHz Filter bandwidth standard, adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter sensitivity @ 400 kHz offset > 20 dB Filter sensitivity @ 600 kHz offset > 30 dB Filter sensitivity @ 1 MHz offset > 35 dB Output power, PEP + 25 dBm Output power, 2 carrier + 19 dBm/carrier Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W

2. Environmental specification Temperature range -13 to + 131 °F Temperature range -25 to + 55 °C Casing class NEMA4/IP65 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 4.3 Inches 385 x 385 x 110 mm Mechanical outline See Compact Low Weight < 22 lbs < 10 kg RF-connectors N-type female Lock type Allgon Safety bolts

LinDAS unit specification

Product Description

UA117 01/1 OCM, Opto Coverter ModuleUA119 01/1 RCM, RF Combining Module


Kjell Knuutinen

Dattum/Date

2001-11-01

Godkänd/Approved Dok nr/Doc no

UA117 01/1-201

Rev

A

Sida/Page

1 (2)

Dok namn/Doc name

PRELIMINARY PRODUCT SPECIFICATIONFil/file

OCM_UA117 01-1_A

Optical Converter Module OCMBase specification for UA117 01/1

The Opto Converter Module OCM is an active module used in Allgon standardized LinDAS (LightIndoor Distributed Antenna System to convert/reconvert RF/opto signals to/from the Central Huband the Remote Hub.

Typical valuesBand width @ 3 dB 800 – 2200 MHzInput impedance 50 OhmMax RF input power +36 dBmLaser transmitter optical wavelength DFB 1310 or 1550 nmOptical receiver wavelength 1250 - 1600 nmOptical RF transmitter/receiverattenuation settable by SW in 1 dB steps

0 – 20 dB

Third order IPin + 55 to +75 dBmReceiver settable alarm level WARNING 0 to -40 dBm in 1 dB stepsReceiver settable alarm level ERROR 0 to -40 dBm in 1 dB stepsSupply voltage 85 – 265 VACPackage (sizes in mm) Standard 19”

W=412 (483 panel)D= 500H= 88 (2U)

Weight Max 5 kgTemp range 0 to +50 CºWeather protection IP42RF connectors SMA-type female (max 6)Opto connectors FC-APC (max 24)

FeaturesOperation capability

- Inbuilt input power meter (optic meter)- Optical output power, software controlled, two levels- IP addressing for supporting large system build out- Settable alarm thresholds (two levels)- Sub carrier for data communication over fiber, only one remote access point- Battery Back-up with charger- External alarm inputs with settable levels and polarity- R2R interface for communication between Allgon HW products via RS485- RCC support- Remote software download- Compatible with OMT and OMS software


Kjell Knuutinen

Dattum/Date

2001-11-01


UA117 01/1-201

Rev

A

Sida/Page

2 (2)

Dok namn/Doc name


OCM_UA117 01-1_A

Alarm capability- No optic power received (Rx)- Laser failure (Tx)- Temperature- Internal voltage- Sub carrier link supervision- External alarm

Declaration of conformity- Environmental specification ETS300 019-2-4- Radio Transmission and Reception ETS300 609-4- EMC emission and immunity ETS300 342-3- EMC immunity IEC 801-2,4 and 5- Radiation Safety of laser products IEC/EN 60 825-1- Safety of IT technology IEC/EN 609 50- US Food and Drug Administration req. Part 1040.10, 1998- Electrical safety IEC publication 65- UL 1950 third Edition- UL CAN/CVSA-C22.2 No 950-M95


Kjell Knuutinen

Dattum/Date

2001-11-01


UA116 01/1-201

Rev

A

Sida/Page

1 (2)

Dok namn/Doc name


RCM_UA116 01-1_A

RF Combining Module RCMBase specification for UA116 01/1

The RF Combiner Module is to be used in the Allgon standardised indoor system LinDAS (LightIndoor Distributed Antenna System).

Typical valuesRF in/out from BTS Max +40 dBm RMS/port Note 1

RF in/out to CM Max +36 dBm (depending on configuration)Impedance 50 OhmPackage (sizes in mm) Standard 19”

W=412 (483 panel)D= 500H= 88 (2U)

Weight Max 4 kgTemp range 0 to +50 CºWeather protection IP42RF connectors BTSIN/OUT

N-type female (Max 24)

RF connectors IN/OUT(to OCM)

SMA-type female (Max 6)

FeaturesThe RCM has a modular design allowing:- single and multiband configurations- single and multi operator capability- Easy up gradable

The RCM is designed in such way that electrical and mechanical data are fullycompatible to Allgon approved sub components like:- Hybrid couplers in frequency range 800-2300 MHz- Duplex filters 800, 900, 1800, 1900 and 2100 MHz frequency bands- Diplex filters for combining 800/1900, 900/1800, 900/2100, 1800/2100 MHz

Diplex/Duplex filters are supposed to work in the frequency bands with respect tostandard duplex spacing like GSM (900/1800/1900), PCS, AMPS/TDMA/iDEN andUMTS

Note 1 Max power handling capability of hybrid input connector. The input power and number of installedhybrid couplers must be in such way that the temperature of the RCM never will exceed 100 C°. Forced aircooling is always to recommend.


Kjell Knuutinen

Dattum/Date

2001-11-01


UA116 01/1-201

Rev

A

Sida/Page

2 (2)

Dok namn/Doc name


RCM_UA116 01-1_A

LinDAS system specification

System

Single band 900 MHzSingle band 1800 MHzDual band 800/1900 MHzDual band 900/1800 MHz


Kjell Knuutinen

Dattum/Date

2001-11-27


RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name


LiNDAS System SpecificationSingle band 900 MHz

Electrical specification (typical values)

System Frequency tuning band Up link 890 – 915 MHz Frequency tuning band Down link 935 – 960 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Adjustable UL gain (typical settings) 1 -10 to 10 dB Gain step resolution 1 dB Out of band gain @ 400 KHz off-set 45 dB Out of band gain @ 600 KHz off-set 40 dB Out of band gain @ 1 MHz off-set 35 dB Out of band gain @ 5 MHz off-set 25 dB Downlink Output power, PEP (no inbuild power split) + 25 dBm Group delay exclusive fibre 6 µs Max Noise figure at max gain, 25° C (no inbuild powersplit)

8 dB

Spur free dynamic range @ 200kHz >70 dB

Max continuous RF power downlink with/without RCM +40/36 dBm Max continuous RF power uplink RH +13 dBm Laser optic wavelength DFB 1310 or 1550 nm Optical output power, two levels SW adjustable + 3/0 dBm Optic return loss > 55 dB Noise power output at max gain, no fiber connected < -135 dBm/Hz Power Consumption Remote Hub + OCM <70 W

Output power (RMS) reference table (dBm) at antenna portNo Carrier 9002 +194 +14

RF Combining Module (RCM)

1 Following parameters are adjustable in the system: RH: 55 – 70 dB, CM: optical transmitter/receiver attenuation range 0 – 20 dB.


Kjell Knuutinen

Dattum/Date

2001-11-27


RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name


RF in/out from BTS Max +40 dBm RMS/portRF in/out to CM Max +36 dBm (depending on configuration)Impedance 50 OhmPackage (sizes in mm) Standard 19”

W=412 (483 panel)D= 500H= 88 (2U)






Kjell Knuutinen

Dattum/Date

2001-11-27


RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name


RF / Opto Converter Module (OCM)

Band width @ 3 dB 800 – 2200 MHzInput impedance 50 OhmLaser transmitter optical wavelength DFB 1310 or 1550 nmOptical receiver wavelength 1250 - 1600 nmOptical RF transmitter/receiverattenuation settable by SW in 1 dB steps

0 – 20 dB

Third order Ipin + 55 to +75 dBmReceiver settable alarm level WARNING 0 to -40 dBm in 1 dB stepsReceiver settable alarm level ERROR 0 to -40 dBm in 1 dB stepsSupply voltage 85 – 265 VACPackage (sizes in mm) Standard 19”

W=412 (483 panel)D= 500H= 88 (2U)



Kjell Knuutinen

Dattum/Date

2001-11-27


RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name


Remote Hub (RH)

Output power PEP (IM –13 dBm) Note 1 + 29 dBmOutput power PEP (IM –30 dBm) Note 1 + 26 dBmOutput power PEP (IM –36 dBm) Note 1 + 25 dBmOutput power PEP @ 4 antenna ports Above –6 dB/portGroupe delay, absolute 6 µsNoise figure @ 25 Cº 8 dBMaximum input power + 13 dBmSupply voltage 85 – 265 VACPower consumption (single band) < 55 WPower consumption (dual band) < 110 WDimension (WxHxD) in mm (single band) 385 x 385 x 110Dimension (WxHxD) in mm (dual band) 385 x 385 x 160Weight (single band) < 10 kgWeight (dual band) < 20 kgTemperature range -20 to +55 CºWeather protection IP65RF connectors N-type female (max 4)

System Features• Inbuilt input power meter (optic meter)• Optical output power, software controlled, two levels• IP addressing over Fiber To Fiber link (F2F)• Settable alarm thresholds (two levels)• Sub carrier for data communication over fiber• Battery Back-up with charger• External alarm inputs with settable levels and polarity• R2R interface• RCC support• Remote software download• Compatible with OMT and OMS software

5. Alarms• Laser failure (Tx)• No optic power received (Rx)• Temperature• Internal voltage• Sub carrier link supervision• External alarm

Note 1 In dual band applications calculate approx. 1 dB loss caused by the inbuilt diplex filters.


Kjell Knuutinen

Dattum/Date

2001-11-27


RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name


ManagementOMT (Operation & Maintenance Terminal) software for local and remote access mainly for installationand commissioning;• PC connected via RS232• PC connected via modem in CM

OMS (Operation & Maintenance System) software for fleet management• T1 connected via modem in CM

Software requirements OMTThe OMT software package requires at least:� Windows 95, 98 or NT version 4.0 or higher� 8 MB of RAM (16 is recommended)� 4 MB free hard disk space

Software requirements OMS� Intel Pentium II based computer, running at a minimum of 450 MHz� 256 MB RAM� 2000 MB available disk space� Monitor capable of displaying a resolution of 1024 x 768 (1280 x 1024 recommended)� Network card and TCP/IP protocol installed� Windows NT4 with service pack 5 or higher

Declaration of conformity- Environmental specification ETS300 019-2-4- Radio Transmission and Reception ETS300 609-4- EMC emission and immunity ETS300 342-3- EMC immunity IEC 801-2,4 and 5- Electrical safety IEC publication 65- Laser safety US Food and Drug Administration req.

Part 1040.10, 1998- UL 1950 third Edition- UL CAN/CVSA-C22.2 No 950-M95- FCC 24E


Kjell Knuutinen

Dattum/Date

2001-11-27


RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name


LiNDAS System SpecificationSingle band 1800 MHz


System Frequency tuning band Up link 2 1710 – 1785 MHz Frequency tuning band Down link 2 1805 – 1880 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Adjustable UL gain (typical settings) 1 -10 to 10 dB Gain step resolution 1 dB Out of band gain @ 400 KHz off-set 45 dB Out of band gain @ 600 KHz off-set 40 dB Out of band gain @ 1 MHz off-set 35 dB Out of band gain @ 5 MHz off-set 25 dB Downlink Output power, PEP (no inbuild power split) + 26 dBm Group delay exclusive fibre 6 µs Max Noise figure at max gain, 25° C (no inbuild powersplit)

8 dB



Output power (RMS) reference table (dBm) at antenna portNo Carrier 18002 +204 +15

1 Following parameters are adjustable in the system: RH: 55 – 70 dB, CM: optical transmitter/receiver attenuation range 0 – 20 dB.2 Upper and lower band is available


Kjell Knuutinen

Dattum/Date

2001-11-27


RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name




W=412 (483 panel)D= 500H= 88 (2U)






Kjell Knuutinen

Dattum/Date

2001-11-27


RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name




0 – 20 dB

Third order Ipin + 55 to +75 dBmReceiver settable alarm level WARNING 0 to -40 dBm in 1 dB stepsReceiver settable alarm level ERROR 0 to -40 dBm in 1 dB stepsSupply voltage 85 – 265 VACPackage (sizes in mm) Standard 19”

W=412 (483 panel)D= 500H= 88 (2U)



Kjell Knuutinen

Dattum/Date

2001-11-27


RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name


Remote Hub (RH)

Output power PEP (IM –13 dBm) Note 1 + 29 dBmOutput power PEP (IM –30 dBm) Note 1 + 26 dBmOutput power PEP (IM –36 dBm) Note 1 + 25 dBmOutput power PEP @ 4 antenna ports Above –6 dB/portGroupe delay, absolute 6 µsNoise figure @ 25 Cº 8 dBMaximum input power + 13 dBmSupply voltage 85 – 265 VACPower consumption (single band) < 55 WPower consumption (dual band) < 110 WDimension (WxHxD) in mm (single band) 385 x 385 x 110Dimension (WxHxD) in mm (dual band) 385 x 385 x 160Weight (single band) < 10 kgWeight (dual band) < 20 kgTemperature range -20 to +55 CºWeather protection IP65RF connectors N-type female (max 4)





Kjell Knuutinen

Dattum/Date

2001-11-27


RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name









Kjell Knuutinen

Dattum/Date

2001-11-27


RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name


LiNDAS System SpecificationDual band 900/1800MHz


System Frequency tuning band Up link 890 – 915 MHz Frequency tuning band Down link 935 – 960 MHz Frequency tuning band Up link 2 1710 – 1785 MHz Frequency tuning band Down link 2 1805 - 1880 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Adjustable UL gain (typical settings) 1 -10 to 10 dB Gain step resolution 1 dB Out of band gain @ 400 KHz off-set 45 dB Out of band gain @ 600 KHz off-set 40 dB Out of band gain @ 1 MHz off-set 35 dB Out of band gain @ 5 MHz off-set 25 dB Downlink Output power, PEP (no inbuild power split) + 25 dBm Group delay exclusive fibre 6 µs Max Noise figure at max gain, 25° C (no inbuild powersplit)

8 dB



Output power (RMS) reference table (dBm) at antenna portNo Carrier 900 18002 +19 +204 +14 +15

1 Following parameters are adjustable in the system: RH: 55 – 70 dB, CM: optical transmitter/receiver attenuation range 0 – 20 dB.2 Upper and lower band is available


Kjell Knuutinen

Dattum/Date

2001-11-27


RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name




W=412 (483 panel)D= 500H= 88 (2U)






Kjell Knuutinen

Dattum/Date

2001-11-27


RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name




0 – 20 dB

Third order IPin + 55 to +75 dBmReceiver settable alarm level WARNING 0 to -40 dBm in 1 dB stepsReceiver settable alarm level ERROR 0 to -40 dBm in 1 dB stepsSupply voltage 85 – 265 VACPackage (sizes in mm) Standard 19”

W=412 (483 panel)D= 500H= 88 (2U)



Kjell Knuutinen

Dattum/Date

2001-11-27


RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name


Remote Hub (RH)

Output power PEP (IM –13 dBm) Note 1 + 29 dBmOutput power PEP (IM –30 dBm) Note 1 + 26 dBmOutput power PEP (IM –36 dBm) Note 1 +25 dBmOutput power PEP @ 4 antenna ports Above –6 dB/portGroupe delay, absolute 6 µsNoise figure @ 25 Cº 8 dBMaximum input power + 13 dBmSupply voltage 85 – 265 VACPower consumption (single band) < 55 WPower consumption (dual band) < 110 WDimension (WxHxD) in mm (single band) 385 x 385 x 110Dimension (WxHxD) in mm (dual band) 385 x 385 x 160Weight (single band) < 10 kgWeight (dual band) < 20 kgTemperature range -20 to +55 CºWeather protection IP65RF connectors N-type female (max 4)





Kjell Knuutinen

Dattum/Date

2001-11-27


RCE200141-201

Rev

A

Sida/Page

Dok namn/Doc name









Kjell Knuutinen

Dattum/Date

2002-01-26


RCE200150-201

Rev

A

Sida/Page

Dok namn/Doc name


LiNDAS System SpecificationDual band 800/1900MHz

Electrical specification

System Frequency tuning band Up link 824 – 849 MHz Frequency tuning band Down link 869 - 894 MHz Frequency tuning band Up link 1870 – 1910 MHz Frequency tuning band Down link 1950 – 1990 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Adjustable UL gain (typical settings) 1 -10 to 10 dB Gain step resolution 1 dB Out of band gain @ 400 KHz off-set 45 dB Out of band gain @ 600 KHz off-set 40 dB Out of band gain @ 1 MHz off-set 35 dB Out of band gain @ 5 MHz off-set 25 dB Downlink Output power, PEP (no inbuild power split) Min + 28 dBm 3rd order intercept point + 49 dBm Group delay exclusive fibre 6 µs Typical Noise figure at max gain, 25° C (no inbuildpower split)

8 dB


Max continuous RF power downlink with/without RCM +40/36 dBm Max continuous RF power uplink RH +13 dBm Laser optic wavelength DFB 1310 or 1550 nm Optical output power, two levels SW adjustable + 3/0 dBm Optic return loss > 55 dB Noise power output at max gain, no fiber connected < -135 dBm/Hz Power Consumption Remote Hub + CM <70 W

Output power (RMS) reference table (dBm) at antenna portNo Carrier CDMA TDMA GSM1 +22 +25 +252 +17 +22 +224 +12 +17 +17

1 Following parameters are adjustable in the system: RH: 55 – 70 dB, CM: optical transmitter/receiver attenuation range 0 – 20 dB.


Kjell Knuutinen

Dattum/Date

2002-01-26


RCE200150-201

Rev

A

Sida/Page

Dok namn/Doc name



RF in/out from BTS Max +40 dBm RMS/portRF in/out to CM Max +36 dBm (depending on

configuration)Impedance 50 OhmPackage (sizes in mm) Standard 19”

W=412 (483 panel)D= 500H= 88 (2U)

Weight Max 4 kgTemp range 0 to +50 C�Weather protection IP42RF connectors BTS IN/OUT N-type female (Max 6)RF connectors IN/OUT (to CM) SMA-type female (Max 24)

RF in/out from BTS Max +40 dBm RMS/portRF in/out to CM Max +36 dBm (depending on

configuration)Impedance 50 OhmPackage (sizes in mm) Standard 19”

W=412 (483 panel)D= 500H= 88 (2U)

Weight Max 4 kgTemp range 0 to +50 C�Weather protection IP42RF connectors BTS IN/OUT N-type female (Max 6)RF connectors IN/OUT (to CM) SMA-type female (Max 24)


Kjell Knuutinen

Dattum/Date

2002-01-26


RCE200150-201

Rev

A

Sida/Page

Dok namn/Doc name


RF / Opto Converter Module (CM)

Band width @ 3 dB 800 – 2200 MHzInput impedance 50 OhmLaser transmitter optical wavelength DFB 1310 or 1550 nmOptical receiver wavelength 1250 - 1600 nmRF transmitter/receiver attenuation settableby SW in 1 dB steps

0 – 20 dB

Receiver settable alarm level WARNING 0 to -40 dBReceiver settable alarm level ERROR 0 to -40 dBmSupply voltage 85 – 265 VACPackage (sizes in mm) Standard 19”

W=412 (483 panel)D= 500H= 88 (2U)

Weight Max 5 kgTemp range 0 to +50 C�Weather protection IP42RF connectors SMA-type female (max 6)Opto connectors FC-APC (max 24)

Band width @ 3 dB 800 – 2200 MHzInput impedance 50 OhmLaser transmitter optical wavelength DFB 1310 or 1550 nmOptical receiver wavelength 1250 - 1600 nmRF transmitter/receiver attenuation settableby SW in 1 dB steps

0 – 20 dB

Receiver settable alarm level WARNING 0 to -40 dBReceiver settable alarm level ERROR 0 to -40 dBmSupply voltage 85 – 265 VACPackage (sizes in mm) Standard 19”

W=412 (483 panel)D= 500H= 88 (2U)

Weight Max 5 kgTemp range 0 to +50 C�Weather protection IP42RF connectors SMA-type female (max 6)Opto connectors FC-APC (max 24)


Kjell Knuutinen

Dattum/Date

2002-01-26


RCE200150-201

Rev

A

Sida/Page

Dok namn/Doc name


Remote Hub (RH)

System Features� Inbuilt input power meter (optic meter)� Optical output power, software controlled, two levels� IP addressing over Fiber To Fiber link (F2F)� Settable alarm thresholds (two levels)� Sub carrier for data communication� Battery Back-up with charger� External alarm inputs with settable levels and polarity� R2R interface� RCC support� Remote software download� Compatible with OMT and OMS software

5. Alarms� Laser failure (Tx)� No optic power received (Rx)� Temperature� Internal voltage� Sub carrier link supervision� External alarm

Max composit output power (IM –13 dBm) + 29 dBmMax composit output power (IM –30 dBm) + 26 dBmMax composit output power (IM –36 dBm) + 25 dBmMax composit output power @ 4 antenna ports Above – 6 dB/portMax absolute group delay 6 µsNoise figure @ 25 C� 8 dBMaximum input power + 13 dBmSupply voltage 85 – 265 VACPower consumption 55 WDimension (WxHxD) in mm 385x385x100Weight 8 kgTemp range 0 to +50 C�Weather protection IP42RF connectors N-type female (max 4)

Max composit output power (IM –13 dBm) + 29 dBmMax composit output power (IM –30 dBm) + 26 dBmMax composit output power (IM –36 dBm) + 25 dBmMax composit output power @ 4 antenna ports Above – 6 dB/portMax absolute group delay 6 µsNoise figure @ 25 C� 8 dBMaximum input power + 13 dBmSupply voltage 85 – 265 VACPower consumption 55 WDimension (WxHxD) in mm 385x385x100Weight 8 kgTemp range 0 to +50 C�Weather protection IP42RF connectors N-type female (max 4)


Kjell Knuutinen

Dattum/Date

2002-01-26


RCE200150-201

Rev

A

Sida/Page

Dok namn/Doc name


OperationSet-up and control of the system via OMT (Operation & Maintenance Terminal) software� PC connected via RS232� PC connected via modem in CM� Set-up, monitoring and control of the system via OMS (Operation & Maintenance System) software� PC connected via modem in CM





Allgon Fiber optic system

Product LinDAS Unit specification LinDAS System specification Allgon Fiber 19” rack BMU

COVERAGE SYSTEMS

System description .doc

Product Description

19” Rack mounted Base station Master Unit

19” Rack mounted Site Distribution Unit

COVERAGE SYSTEMS

1 (13)

Table of content

List of abbreviations ............................................................................. 2

General Information ............................................................................. 3

System Concept ................................................................................... 4

Features & Advantages ........................................................................ 5

Product Description.............................................................................. 6

POI – Point Of Interconnect...................................................................................................................... 6 OCU - Optical Conversion Unit ............................................................................................................... 8 XCU – Cross Coupling Unit ...................................................................................................................... 10

Declaration of Conformity ................................................................... 12 Copyright © Allgon Systems AB 2002 Issued by: Allgon Coverage SE-187 80 Täby, Sweden [email protected] The reproduction, transmission or use of this document or its contents is not permitted without expressed written authority. Offenders will be liable for damages. All rights, including rights created by patent grant or registration of a utility model or design, are reserved. Technical specifications and features are binding only insofar as they are specifically and expressly agreed upon in a written contract.

COVERAGE SYSTEMS

2 (13)

List of abbreviations BMU BTS

Base Station Master Unit Base station Transceiver System

CH Central Hub DAN Distributed Antenna Network DL Down Link ETS European Telecommunication Standards FCC Federal Communications Commission FON Fibre Optic Node IM Inter modulation LAN Local Area Network LED Light Emitted Diode OMS Operation & Maintenance System OMT Operation & Maintenance Terminal OCU PEP

Optical Conversion Unit Peak Envelope Power

POI PSTN

Point Of Interconnect Public Switched Telephone Network

RF Radio Frequency RH Remote Hub R2R Repeater to Repeater (communication link) RMS Root Mean Square Rx Receiver SDU Tx

Site Distribution Unit Transmitter

UL Up Link VAC Voltage Alternating Current VDC Voltage Direct Current WAN Wide Area Network WDM Wave length Division Multiplexing XCU 3G

Cross Coupling Unit Third Generation mobile system

COVERAGE SYSTEMS

3 (13)

General Information The new 19” product line is a unique, cost-efficient solution for multi-operator systems. The concept offers unlimited functionality and flexibility, since all modules are custom designed. It provides RF signal combining and optical distribution for radio systems from 800 to 2400 MHz. The BMU is located at the BTS site and converts the RF signals to light after the separate RF signals have been combined. The SDU, used for multi-operator and multi-band systems, is located at the repeater site and converts the light to a RF signal and separates each RF band before amplifying the signal through the repeater. A flexible, modular concept employing Allgon’s in-house mini-filter and optical technology guarantees quality and meets tough lead-time demands. Allgon Coverage Engineering works closely with customers to draw up specifications and designs for all systems. Well proven Technology The products are based on the well-proven Allgon repeater platforms and focus on cost-effective coverage while maintaining quality and flexibility. Our standard repeater and fiber optic products are successfully used in RF applications for subways, road tunnels and airports. These applications exist in harsh environments and require equipment with a special focus on robust mechanical design, weather protection while providing for high level of supervision and control.

COVERAGE SYSTEMS

4 (13)

System Concept The Allgon Fiber Optic Distribution System converts the RF signals at the BTS location to FO light and distributes the signal to the local sites where the signal will be re-converted to RF. The BMU consists of three types of modules.

• OCU – Optical Conversion Unit • POI – Point Of Interconnect • XCU – Cross Coupling Unit

The SDU consists of two types of modules.

• OCU – Optical Conversion Unit • POI – Point Of Interconnect

Figure 1. 19” Fibre Optic Distribution System

COVERAGE SYSTEMS

5 (13)

Features & Advantages Allgon 19” Fiber Optic Distribution system distinguishes itself from the competitors systems in the following areas: • The products will meet future demands for high signal quality. In high data

speed systems like 3G the signal to noise ratio is crucial for system performance.

• The fiber optic distribution system is an operator selective system using IF

filtering techniques to minimize noise and interference to the BTS. Interference and noise contribution caused by less precise products will cause increased drop calls and a lower grade of service.

• The fiber optic system has a high dynamic range that allow distribution of the

signal over long fiber runs and/or use of optical splitters for distributing the signals to several repeaters serving several antennas. The dynamic range correlate also with the tougher dynamic range requirements for mobile stations operating in near field indoor environment.

• The low noise figure of the fiber optic system improves uplink performance

considerably, and the system will not be uplink limited even for a large DAN with multiple repeaters. This is especially important in CDMA systems where reduced noise is directly translates into increased capacity.

• The POI is designed to combine multiple operator’s frequency bands and

sectors into one common distribution network. The system includes special high performance miniature diplex and duplex filters for compact integration.

• Complete Management. The fiber optic distribution system can be controlled

and monitored by using a sophisticated management platform that can handle large multi user systems with alarm integration to an overlaying operator’s management system. Also products used in the system are fully compatible with all other Allgon repeater products already in operation.

• The Fiber Optic Distribution System is custom tailored and will be unique

configured to meet operators’ system requirements. • The Fiber Optic System has a modular design and permits an easy upgrade

from 2 G to 3G.

COVERAGE SYSTEMS

6 (13)

Product Description

POI – Point Of Interconnect The POI is a passive unit and interface directly with the base station (BMU) and the repeaters (SDU) via coaxial cables. The POI has a custom tailored modular design allowing:

- single and multi band configurations - single and multi operator capability - easily up-gradable

The POI is designed i n such way that electrical and mechanical data are fully compatible to Allgon approved sub components like:

- Hybrid couplers in frequency range 800-2300 MHz - Duplex filters 800, 900, 1500, 1800, 1900 and 2100 MHz frequency bands - Diplex filters for combining 450/800/900, 800/1900, 900/1800, 900/2100,

1800/2100 MHz Diplex/Duplex filters are supposed to work in the frequency bands with respect to standard duplex spacing like GSM (900/1800/1900), PCS, AMPS/TDMA/iDEN and UMTS.

Figure 2. POI

OCU RF IN/OUT

BTS RF IN/OUT to/from BTS

Cross coupling panel

COVERAGE SYSTEMS

7 (13)

Note!

• The POI is customer configurable. Not used connectors (blind holes) are protected with a cover plate.

Main characteristics RF in/out from BTS Max +50 dBm total RMSNote 1

Max +40 dBm RMS/port Note 1

RF in/out to OCU Max +36 dBm (depending on configuration) Impedance 50 Ohm Package (sizes in mm) Standard 19”

W=412 (483 panel) D= 500 H= 132,5 (3U)

Weight Max 5 kg Temp range 0 to +50 Cº Weather protection IP42 RF connectors BTS IN/OUT

N-type and/or 7/16 female (Max 12)

RF connectors IN/OUT (to OCU)


Cross coupling connectors IN/OUT


Note 1 Max power handling capability of hybrid input connector. The input power and number of installed hybrid couplers must be in such way that the temperature of the POI never will exceed 100 C°. Forced air cooling is always to recommend.

COVERAGE SYSTEMS

8 (13)

OCU - Optical Conversion Unit The Optical Conversion Unit OCU is an active unit used within ACE Product concept to convert/reconvert RF/optical signals to/from the BTS and the remote site.

Figure 3. OCU

ANT External antenna for radio modem

RF IN/OUT To/from RCM

STATUS LED Indication ofFibre link

OPTO IN/OUT Optical connection to RH

FON Configuration/communication interface to the Fibre optical board

WLI - Wire link interface for communication between different units in a repeatre

REMOTE Modem connection

Mains switch

External alarm in

COVERAGE SYSTEMS

9 (13)

OCU optional • Up to 4 FON boards • 85 –265 VAC or 24/48 VDC power supply • Standard Hayes compatible PSTN wireline modem or radio modems for cellular

standards GSM900, GSM1800, GSM1900, CDMA800, CDMA1900 and AMPS/TDMA

• WDM for supporting one fibre for UL and DL • Optical splitters for serial or cascade connection to fiber optic repeater Note!

The OCU is customer configurable. Not used connectors (blind holes) are protected with a cover plate

Main characteristics Band width @ 3 dB 800 – 2200 MHz Input impedance 50 Ohm Max RF input power +36 dBm Laser transmitter optical wavelength DFB 1310 or 1550 nm Optical receiver wavelength 1250 - 1600 nm Optical RF transmitter/receiver attenuation settable by SW in 1 dB steps

0 – 20 dB

Third order IPin + 55 to +75 dBm Receiver settable alarm level WARNING 0 to -40 dBm in 1 dB steps Receiver settable alarm level ERROR 0 to -40 dBm in 1 dB steps Supply voltage 85 – 265 VAC Package (sizes in mm) Standard 19”

W=412 (483 panel) D= 500 H= 177 (4U)

Weight Max 10 kg Temp range 0 to +50 Cº Weather protection IP42 RF connectors SMA-type female (max 8) Optical connectors DIN-APC (max 32)

COVERAGE SYSTEMS

10 (13)

XCU – Cross Coupling Unit The XCU has a custom tailored modular design depending on the number of FON boards included in the OCU. The XCU will split each BTS signal into four outputs on the front panel for cross coupling capability.

The XCU is designed in such way that electrical and mechanical data are fully compatible to Allgon approved sub components like: - Hybrid couplers in frequency range 800-2300 MHz - Duplex filters 800, 900, 1500, 1800, 1900 and 2100 MHz frequency bands Duplex filters are supposed to work in the frequency bands with respect to standard duplex spacing like GSM (900/1800/1900), PCS, AMPS/TDMA/iDEN and UMTS.

Figure 4. XCU

POI RF IN/OUT

BTS RF IN/OUT to/from BTS

Advanced Cross coupling panel

COVERAGE SYSTEMS

11 (13)

Main characteristics RF in/out from BTS Max +50 dBm total RMSNote 1

Max +40 dBm RMS/port Note 1

RF in/out to POI Max +36 dBm Impedance 50 Ohm Package (sizes in mm) Standard 19”

W=412 (483 panel) D= 500 H= 132,5 (3U)

Weight Max 5 kg Temp range 0 to +50 Cº Weather protection IP42 RF connectors BTS IN/OUT

N-type and/or 7/16 female (Max 12)

RF connectors IN/OUT (to POI)


Cross coupling connectors IN/OUT


Note 1 Max power handling capability of hybrid input connector. The input power and number of installed hybrid couplers must be in such way that the temperature of the RCM never will exceed 100 C°. Forced air cooling is always to recommend.

COVERAGE SYSTEMS

12 (13)

Declaration of Conformity Allgon Coverage System includes a number of generic hardware-, software-, communication- and fibre optic platforms. This forms the base of our product portfolio including repeater and DAS products for all major cellular standards. Environmental All products are design in accordance with ETS300 019-2-4, class 1: “Stationary use at non-weather protected locations, extended climate tests” EMC, emission part • ETS300 342-3 • FCC (part 15, 22 and 24) EMC, immunity part • ETS301 489-1 • FCC (part 15, 22 and 24) Radio Transmission and Reception • ETS301 502 • FCC (part 15, 22 and 24) Safety • EN60950: 1992 • UL 1950 third edition and CAN/CSA C22.2 No 950-95, 1995 Fibre Optic Safety Class 1 product • IEC/EN60 825-1 Radiation safety of laser products for Europe and Canada • IEC/EN 60950 2:nd edition • US Food and Drug Administration requirements part 1040.10, 1998

Product list

2002-12-19

Product nr. InformationABR5500/00101 Repeater DMB-1500 MhzALM1200/00202 Compact Maritime 900 MHz ABW 25 MHz, RCCALM2200/00202 Compact Maritime 1800 MHz ABW 25 MHz, RCCALR1200/00101 Compact 900 MHz, ABW 15 MHzALR1200/00102 Compact 900 MHz, ABW 15 MHz, RCCALR1200/00201 Compact 900 MHz, ABW 25 MHzALR1200/00202 Compact 900 MHz, ABW 25 MHz, RCCALR1200/00401 Compact 900 MHz, ABW 25 MHz, DCALR1200/00402 Compact 900 MHz, ABW 25 MHz, DC, RCCALR1200/04201 Compact 900 MHz, ABW 25 MHz ChinaALR1200/04202 Compact 900 MHz, ABW 25 MHz, RCC, ChinaALR1200/90101 Compact 900 MHz EGSM, ABW 15 MHzALR1200/90102 Compact 900 MHz EGSM, ABW 15 MHz, RCCALR1212/00101 Compact Dual 900 15 MHzALR1212/00102 Compact Dual 900 15 MHz, RCCALR1212/00201 Compact Dual 900 25 MHzALR1212/00202 Compact Dual 900 25 MHz, RCCALR2200/00101 Compact BS-1800 LB 15ALR2200/00102 Compact BS-1800 LB 15 RCCALR2200/00201 Compact BS-1800 LB 25 MHz ALR2200/00202 Compact BS-1800 LB 25 MHz RCCALR2200/90101 Compact BS-1800 UB 15ALR2200/90102 Compact BS-1800 UB 15 RCCALR2200/90201 Compact BS-1800 UB 25 MHz ALR2200/90202 Compact BS-1800 UB 25 MHz RCCALR2212/00101 Compact BS Dual1800/900 LBALR2212/00102 Compact Dual 1800/ 900 15 MHz, RCCALR2212/90101 Compact.BS Dual 1800/900 UBALR2212/90102 Compact.BS Dual 1800/900 UB, RCCALR2222/00101 Compact BS Dual 1800 15ALR2222/00102 Compact BS Dual 1800 15 RCCALR2222/09501 Compact BS Dual 1800 15 LB, UB 1 service 1 donorALR2222/09502 Compact BS Dual 1800 15 LB, UB 1 service 1 donor RCCALR3200/00101 Compact BS1900 LBALR3200/00102 Compact BS1900 LB, RCC GSMALR3200/90101 Compact BS1900 UBALR3200/90102 Compact BS1900 UB, RCC GSMALR3232/00101 Compact Dual 1900 LBALR3232/00102 Compact Dual 1900 LB, RCC GSMALR3232/09501 Compact Dual 1900 LB, UB 1 service 1 donorALR3232/09502 Compact Dual 1900 LB, UB 1 service 1 donor RCC GSMALR3232/90101 Compact Dual 1900 UBALR3232/90102 Compact Dual 1900 UB, RCC GSMALR3242/00101 Compact Dual 1900/800 LB 15+15 MHzALR3242/00102 Compact Dual 1900/800 LB 15+15 MHz RCC GSMALR3242/00301 Compact Dual 1900/800 LB 15+15 MHz 1 service 2 donor ALR3242/00302 Compact Dual 1900/800 LB 15+15 MHz 1 service 2 donor, RCC GSMALR3242/90201 Compact Dual 1900/800 UB 25+25 MHzALR3242/90202 Compact Dual 1900/800 UB 25+25 MHz, RCC GSM

ALR3242/90301 Compact Dual 1900/800 UB 15+15 MHz 1 service 2 donor ALR3242/90302 Compact Dual 1900/800 UB 15+15 MHz 1 service 2 donor, RCC GSMALR3242/00501 Compact Dual 1900/800 LB 15+15 MHz 1 service 1 donor ALR3242/00502 Compact Dual 1900/800 LB 15+15 MHz 1 service 1 donor. RCC GSMALR3242/90501 Compact Dual 1900/800 UB 15+15 MHz 1 service 1 donor ALR3242/90502 Compact Dual 1900/800 UB 15+15 MHz 1 service 1 donor, RCC GSMALR3246/00301 Compact Dual 1900/800 SMR LB 15+15 MHz 1 service 2 donorALR4200/00101 Compact BS 800 15 MHzALR4200/00102 Compact BS 800 15 MHz, RCC TDMAALR4200/00201 Compact BS 800 25MHzALR4200/00202 Compact BS 800 25MHz, RCC TDMAALR4242/00101 Compact Dual 800 15ALR4242/00102 Compact Dual 800 15 RCC TDMAALR4600/00101 Compact 800 SMR-IDENALT1200/00202 Compact In-Train 900, 25 MHz, RCCALT2200/00202 Compact In-Train 1800, 25 MHz, RCCAM1200/00202 Repeater Maritime 900 MHz, 25 MHz, RCUAM2200/00202 Repeater Maritime 1800 MHz, 25 MHz, RCUAR1100/00201 Repeater GSM900 2 ch 230VACAR1100/00202 Repeater GSM900 2 ch 230VAC, RCUAR1100/00203 Repeater GSM900 2 ch 24VDCAR1100/00204 Repeater GSM900 2 ch 24VDC, RCUAR1100/00205 Repeater GSM900 2 ch 48 VDCAR1100/00206 Repeater GSM900 2 ch 48, RCUAR1100/00207 Repeater GSM900 2 ch 115VDCAR1100/00208 Repeater GSM900 2 ch 115VDC, RCUAR1100/00401 Repeater GSM900 4 ch 230VACAR1100/00402 Repeater GSM900 4 ch 230VAC, RCUAR1100/00403 Repeater GSM900 4 ch 24VDCAR1100/00404 Repeater GSM900 4 ch 24VDC, RCUAR1100/00405 Repeater GSM900 4 ch 48 VDCAR1100/00406 Repeater GSM900 4 ch 48 VDC, RCUAR1100/00407 Repeater GSM900 4 ch 115VACAR1100/00408 Repeater GSM900 4 ch 115VAC, RCUAR1100/80201 Repeater RGSM900 2 ch 230VACAR1100/80202 Repeater RGSM900 2 ch 230VAC, RCUAR1100/80203 Repeater RGSM900 2 ch 24VDCAR1100/80204 Repeater RGSM900 2 ch 24VDC+RCUAR1100/80205 Repeater RGSM900 2 ch 48VDCAR1100/80206 Repeater RGSM900 2 ch 48VDC, RCUAR1100/90202 Repeater EGSM 2 ch 230VAC, RCUAR1100/90204 Repeater EGSM 2 ch 24VDC, RCU.AR1100/90206 Repeater EGSM 2 ch 48VDC, RCU.AR1100/90401 Repeater EGSM 4 ch 230VAC.AR1100/90402 Repeater EGSM 4 ch 230VAC, RCU.AR1100/90404 Repeater EGSM 4 ch 24VDC, RCUAR1100/90406 Repeater EGSM 4 ch 48VDC, RCUAR1111/00601 Repeater GSM900 6 ch 230VACAR1111/00602 Repeater GSM900 6 ch 230VAC, RCUAR1111/00603 Repeater GSM900 6 ch 24VDCAR1111/00604 Repeater GSM900 6 ch 24VDC, RCUAR1111/00605 Repeater GSM900 6 ch 48VDCAR1111/00606 Repeater GSM900 6 ch 48VDC, RCUAR1111/00801 Repeater GSM900 8 ch 230VACAR1111/00802 Repeater GSM900 8 ch 230VAC, RCUAR1111/00803 Repeater GSM900 8 ch 24VDC

AR1111/00804 Repeater GSM900 8 ch 24VDC, RCUAR1111/04201 Repeater Dual Cell GSM 900 4+2 ch 230VACAR1111/04202 Repeater Dual Cell GSM 900 4+2 ch 230VAC, RCUAR1111/04401 Repeater Dual Cell GSM 900 4+4 ch 230VACAR1111/04402 Repeater Dual Cell GSM 900 4+4 ch 230VAC, RCUAR1111/90601 Repeater EGSM 6 ch 230VACAR1111/90602 Repeater EGSM 6 ch 230VAC, RCUAR1111/90606 Repeater EGSM 6 ch 48VDC, RCUAR1111/90801 Repeater EGSM 8 ch 230VACAR1111/90802 Repeater EGSM 8 ch 230VAC, RCUAR1111/90806 Repeater EGSM 8 ch 48VDC, RCUAR1200/04301 Repeater, BS 25 MHz 230 VAC, ChinaAR1200/04302 Repeater, BS 25 MHz 230 VAC, RCU, ChinaAR1200/05201 Repeater, BS 16,5 MHz 230VACAR1200/05202 Repeater, BS 16,5MHz 230VAC, RCUAR1200/05203 Repeater, BS 16,5MHz 21-60VDCAR1200/05204 Repeater, BS 16,5MHz 21-60VDC, RCUAR1200/05301 Repeater, BS 25 MHz 230VACAR1200/05302 Repeater, BS 25 MHz 230VAC, RCUAR1200/95201 Repeater, EGSM, BS 16,9 MHz 230VACAR1200/95202 Repeater, EGSM, BS 16,9 MHz 230VAC, RCUAR1200/95203 Repeater, EGSM, BS 16,9 MHz 21-60VDCAR1200/95204 Repeater, EGSM, BS 16,9 MHz 21-60VDC, RCUAR1212/05201 Repeater, Dual BS 900. 16,9 MHz 230VACAR1212/05202 Repeater, Dual BS 900. 16,9 MHz 230VAC, RCUAR1212/05203 Repeater, Dual BS 900. 16,9 MHz 21-60VDCAR1212/05204 Repeater, Dual BS 900. 16,9 MHz 21-60VDC, RCUAR2100/00201 Repeater DCS-1800 2 ch.LB 230VACAR2100/00202 Repeater DCS-1800 2 ch.LB 230VAC, RCUAR2100/00203 Repeater DCS-1800 2 ch.LB 24VDCAR2100/00204 Repeater DCS-1800 2 ch.LB 24VDC RCUAR2100/00207 Repeater DCS-1800 2 ch LB 115VACAR2100/00208 Repeater DCS-1800 2 ch.LB 115VAC, RCUAR2100/00401 Repeater DCS-1800 4 ch.LB 230VACAR2100/00402 Repeater DCS-1800 4 ch.LB 230VAC,RCUAR2100/00407 Repeater DCS-1800 4 ch.LB 115VACAR2100/00408 Repeater DCS-1800 4 ch.LB 115VAC, RCUAR2100/90201 Repeater DCS-1800 2 ch.UB 230VACAR2100/90202 Repeater DCS-1800 2 ch.UB 230VAC, RCUAR2100/90207 Repeater DCS-1800 2 ch UB 115VACAR2100/90208 Repeater DCS-1800 2 ch UB 115VAC, RCUAR2100/90401 Repeater DCS-1800 4 ch.UB 230VACAR2100/90402 Repeater DCS-1800 4 ch.UB 230VAC, RCUAR2111/02201 Repeater Dual 1800/900 2+2 ch LB 230VACAR2111/02401 Repeater Dual 1800/900 2+4 ch LB 230VACAR2111/04401 Repeater Dual 1800/900 4+4 ch LB 230VACAR2111/04402 Repeater Dual 1800/900 4+4 ch LB 230VAC RCUAR2111/54401 Repeater Dual 1800/900 4+4 ch FB 230VACAR2111/54402 Repeater Dual 1800/900 4+4 ch FB 230VAC RCUAR2111/94401 Repeater Dual 1800/900 4+4 ch UB 230VACAR2111/94402 Repeater Dual 1800/900 4+4 ch UB 230VAC, RCUAR2121/00601 Repeater DCS-1800 6 ch LB 230VACAR2121/00602 Repeater DCS-1800 6 ch LB 230VAC RCUAR2121/00606 Repeater DCS-1800 6 ch LB 48VDC RCUAR2121/00801 Repeater DCS-1800 8 ch LB 230VACAR2121/00802 Repeater DCS-1800 8 ch LB 230VAC, RCU

AR2121/00806 Repeater DCS-1800 8 ch LB 48VDC, RCUAR2121/90601 Repeater DCS-1800 6 ch UB 230VACAR2121/90602 Repeater DCS-1800 6 ch UB 230VAC RCUAR2121/90801 Repeater DCS-1800 8 ch UB 230VACAR2122/02101 Repeater DCS-1800 2 ch/BS 16,9 LB 230VACAR2122/02107 Repeater DCS-1800 2 ch/BS 16,9 LB 115VACAR2142/04201 Repeater Dual 1800 4 CH/800 BS 230VACAR2142/04202 Repeater Dual 1800 4 CH/800 BS 230VAC RCUAR2142/04207 Repeater Dual 1800 4 CH/800 BS 115VACAR2200/00101 Repeater BS1800 LB adj 16,9 MHZ 230VACAR2200/00102 Repeater BS1800 LB adj 16,9 MHz 230VAC, RCUAR2200/00103 Repeater BS1800 LB adj 16,9 MHz 21-60VDCAR2200/00104 Repeater BS1800 LB adj 16,9 MHz 21-60VDC, RCUAR2200/00107 Repeater BS1800 LB adj 16,9 MHz 115VACAR2200/00108 Repeater BS1800 LB adj 16,9 MHz 115VAC, RCUAR2200/90101 Repeater BS1800 UB adj 16,9 MHz 230VACAR2200/90102 Repeater BS1800 UB adj 16,9 MHz 230VAC, RCUAR2200/90103 Repeater BS1800 UB adj 16,9 MHz 21-60VDCAR2200/90104 Repeater BS1800 UB adj 16,9 MHz 21-60VDC, RCUAR2212/95201 Repeater Dual BS1800/BS900 UB 230VACAR2212/95202 Rep. Dual BS1800/BS900 UB 230VAC, RCUAR2212/95203 Rep. Dual BS1800/BS900 UB 21-60VDCAR2212/95204 Rep. Dual BS1800/BS900 UB 21-60VDC, RCUAR2222/00207 Rep. Dual BS1800 LB 115VACAR3100/00201 Repeater GSM1900 2 ch.LB 115 VACAR3100/00204 Repeater GSM1900 2 ch.LB 24 VDC, RCUAR3100/00207 Repeater GSM1900 2 ch.LB 230VACAR3100/00401 Repeater GSM1900 4 ch.LB 115VACAR3100/00404 Repeater GSM1900 4 ch.LB 24VDC, RCUAR3100/00407 Repeater GSM1900 4 ch.LB 230VACAR3100/00408 Repeater GSM1900 4 ch.LB 230VAC RCUAR3100/50201 Repeater GSM1900 2 ch FB, 115 VAR3100/50207 Repeater GSM1900 2 ch FB, 230 VAR3100/50401 Repeater GSM1900 4 ch FB 115VACAR3100/50404 Repeater GSM1900 4 ch FB 24VDC RCUAR3100/50407 Repeater GSM1900 4 ch FB 230VACAR3100/90201 Repeater GSM1900 2 ch.UB 115VACAR3100/90207 Repeater GSM1900 2 ch UB 230VACAR3131/02201 Repeater Dual GSM1900 2+2 CH LB 115VACAR3131/04401 Repeater Dual GSM1900 4+4 CH LB 115VACAR3131/92201 Repeater Dual GSM1900 2+2 CH UB 115VACAR3400/00101 Repeater BS 1900 LB, 115 VAR3400/00103 Repeater BS 1900 LB, 21-60VDCAR3400/00104 Repeater BS 1900 LB, 21-60VDC, RCUAR3400/00107 Repeater BS 1900 LB, 230 VAR3400/01101 Repeater BS CDMA 1900 LB, 115 VAR3400/01102 Repeater BS CDMA 1900 LB, 115 V RCUAR3400/01103 Repeater BS CDMA 1900 LB, 21-60VDCAR3400/01104 Repeater BS CDMA 1900 LB, 21-60VDC, RCUAR3430/01101 Repeater BS CDMA 1900 LB HP, 115 VAR3430/01102 Repeater BS CDMA 1900 LB HP, 115 V RCUAR3400/90101 Repeater BS 1900 UB 115VACAR3400/90103 Repeater BS 1900 UB 21-60VDCAR3400/90104 Repeater BS 1900 UB 21-60VDC, RCUAR3400/90107 Repeater BS 1900 UB 230VACAR3400/91101 Repeater BS CDMA 1900 UB, 115 V

AR3400/91102 Repeater BS CDMA 1900 UB, 115 V RCUAR3430/91101 Repeater BS CDMA 1900 UB HP, 115 VAR3430/91102 Repeater BS CDMA 1900 UB HP, 115 V RCUAR3434/00101 Repeater Dual BS 1900 TDMA LB 115VACAR3434/51101 Repeater Dual BS 1900 CDMA FB 115VACAR3434/51102 Repeater Dual BS 1900 CDMA FB 115VAC, RCUAR3434/51103 Repeater Dual BS 1900 CDMA FB 21-60VDCAR3434/51104 Repeater Dual BS 1900 CDMA FB 21-60VDC, RCUAR3442/05201 Repeater Dual BS1900/800 LB 115VACAR3442/05301 Repeater Dual BS1900/800 LB, 25 MHz 115VACAR3442/05303 Repeater Dual BS1900/800 LB, 25 MHz 24VDCAR3446/01101 Repeater Dual BS CDMA 1900/800 SMR LB, 115 VACAR3500/00101 Repeater CDMA-1900 2 CH 115VAC LBAR3500/00103 Repeater CDMA-1900 2 CH 21-60VDC LBAR3500/00104 Repeater CDMA-1900 2 CH 21-60VDC, RCU LBAR3500/00107 Repeater CDMA-1900 2 CH 230VAC LBAR3500/05101 Repeater CDMA-1900 2 CH MRX 115VAC LBAR3500/05103 Repeater CDMA-1900 2 CH MRX 21-60VDC LBAR3500/05104 Repeater CDMA-1900 2 CH MRX 21-60VDC, RCU LBAR3500/05107 Repeater CDMA-1900 2 CH MRX 230VAC LBAR3500/90101 Repeater CDMA-1900 UB 2 CH 115VACAR3500/90103 Repeater CDMA-1900 UB 2 CH 21-60VDCAR3500/90104 Repeater CDMA-1900 UB 2 CH 21-60VDC, RCUAR3500/90107 Repeater CDMA-1900 UB 2 CH 230VACAR3500/95107 Repeater CDMA-1900 UB 2 CH MRX 230VACAR3530/05101 Repeater CDMA-1900 MRX HP 2 CH 115VAC LBAR3530/05103 Repeater CDMA-1900 MRX HP 2 CH 21-60VDC LBAR3530/05104 Repeater CDMA-1900 MRX HP 2 CH 21-60VDC, RCU LBAR3530/05107 Repeater CDMA-1900 MRX HP 2 CH 230VAC LBAR3530/95101 Repeater CDMA-1900 MRX HP 2 CH 115VAC UBAR3530/95102 Repeater CDMA-1900 MRX HP 2 CH 115VAC UB RCUAR3530/95103 Repeater CDMA-1900 MRX HP 2 CH 24VDC UBAR3530/95104 Repeater CDMA-1900 MRX HP 2 CH 24VDC UB RCUAR3530/95107 Repeater CDMA-1900 MRX HP 2 CH 230VAC UBAR3535/95107 Repeater CDMA-1900 MRX 4 CH 230VAC UBAR3434/51101 Repeater Dual CDMA 1900 BS, 16,5 MHz, LB, UBAR3434/51102 Repeater Dual CDMA 1900 BS, 16,5 MHz, LB, UB RCUAR3434/51103 Repeater Dual CDMA 1900 BS, 16,5 MHz, 21-60VDC LB, UBAR3434/51104 Repeater Dual CDMA 1900 BS, 16,5 MHz, 21-60 VDC LB, UB RCUAR3535/00201 Repeater CDMA-1900 4 CH 115VAC LBAR3535/00202 Repeater CDMA-1900 4 CH 115VAC LB, RCUAR3535/00203 Repeater CDMA-1900 4 CH 21-60 VDC LBAR3535/00204 Repeater CDMA-1900 4 CH 21-60 VDC LB, RCUAR3535/00207 Repeater CDMA-1900 4 CH 230VAC LBAR3535/02201 Repeater CDMA-1900 2+2 CH 115VAC LBAR3535/02202 Repeater CDMA-1900 2+2 CH 115VAC, RCU LBAR3535/02203 Repeater CDMA-1900 2+2 CH 21-60VDC LBAR3535/02204 Repeater CDMA-1900 2+2 CH 21-60VDC, RCU LBAR3535/02207 Repeater CDMA-1900 2+2 CH 230VAC LBAR3535/90201 Repeater CDMA-1900 4 CH 115VAC UBAR3535/90202 Repeater CDMA-1900 4 CH 115VAC UB, RCUAR3535/90203 Repeater CDMA-1900 4 CH 21-60VDC UBAR3535/90204 Repeater CDMA-1900 4 CH 21-60VDC UB, RCUAR3535/90207 Repeater CDMA-1900 4 CH 230VAC UBAR3535/90208 Repeater CDMA-1900 4 CH 230VAC UB, RCUAR3535/92201 Repeater CDMA-1900 2+2 CH UB 115VAC

AR3535/92202 Repeater CDMA-1900 2+2 CH UB 115VAC, RCUAR3535/92203 Repeater CDMA-1900 2+2 CH UB 21-60VDCAR3535/92204 Repeater CDMA-1900 2+2 CH UB 21-60VDC, RCUAR3535/92207 Repeater CDMA-1900 2+2 CH UB 230VACAR3535/95107 Repeater CDMA-1900 4 CH UB MRX 230VACAR3542/05201 Repeater Dual CDMA1900/BS800 115VAC LBAR3542/05203 Repeater Dual CDMA1900/BS800 21-60VDC LBAR3542/05204 Repeater Dual CDMA1900/BS800 21-60VDC, RCU LBAR4200/01201 Repeater BS CDMA 800, 25 MHz 230 VAR4200/01202 Repeater BS CDMA 800, 25 MHz 230 V RCUAR4200/01203 Repeater BS CDMA 800, 25 MHz 21-60VDCAR4200/01204 Repeater BS CDMA 800, 25 MHz 21-60VDC RCUAR4200/01207 Repeater BS CDMA 800, 25 MHz 115VACAR4200/01208 Repeater BS CDMA 800, 25 MHz 115 VAC RCUAR4200/05201 Repeater BS 800 16,9 230VACAR4200/05203 Repeater BS 800 16,9 21-60VDCAR4200/05204 Repeater BS 800 16,9 21-60VDC, RCUAR4200/05207 Repeater BS-800 16,9 115VACAR4200/05301 Repeater BS 800 25 230VACAR4200/05303 Repeater BS 800 25 21-60VDCAR4200/05304 Repeater BS 800 25 21-60VDC, RCUAR4200/05307 Repeater BS 800 25 115VACAR4240/01201 Repeater BS CDMA 800 HP, 25 MHz 230 VAC AR4240/01202 Repeater BS CDMA 800 HP, 25 MHz 230 VAC RCUAR4240/01203 Repeater BS CDMA 800 HP, 25 MHz 21-60 VDC AR4240/01204 Repeater BS CDMA 800 HP, 25 MHz 21-60 VDC RCUAR4240/01207 Repeater BS CDMA 800 HP, 25 MHz 115 VAC AR4240/01208 Repeater BS CDMA 800 HP, 25 MHz 115 VAC RCUAR4242/01101 Repeater Dual BS CDMA 800 16,9 230VACAR4242/01102 Repeater Dual BS CDMA 800 16,9 230VAC, RCUAR4242/01103 Repeater Dual BS CDMA 800 16,9 21-60VDCAR4242/01104 Repeater Dual BS CDMA 800 16,9 21-60VDC, RCUAR4242/01107 Repeater Dual BS CDMA 800 16,9 115VACAR4242/01108 Repeater Dual BS CDMA 800 16,9 115VAC, RCUAR4242/01207 Repeater Dual BS CDMA 800 25 MHz 115VACAR4242/05201 Repeater Dual BS 800 16,9 230VACAR4242/05203 Repeater Dual BS 800 16,9 21-60VDCAR4242/05204 Repeater Dual BS 800 16,9 21-60VDC, RCUAR4242/05207 Repeater Dual BS 800 16,9 115VACAR4500/00141 Repeater CDMA-800 2 CH 230VACAR4500/00142 Repeater CDMA-800 2 CH 230VAC, RCUAR4500/00147 Repeater CDMA-800 2 CH 115VACAR4500/05141 Repeater CDMA-800 2 CH 230VAC, MRXAR4500/05142 Repeater CDMA-800 2 CH 230VAC, RCU, MRXAR4500/05147 Repeater CDMA-800 2 CH 115VAC, MRXAR4500/05148 Repeater CDMA-800 2 CH 115VAC, MRX, RCUAR4540/05141 Repeater CDMA-800 2 CH 230VAC, MRX HPAR4540/05142 Repeater CDMA-800 2 CH 230VAC, MRX, HP, RCUAR4540/05147 Repeater CDMA-800 2 CH 115VAC, MRX, HPAR4540/05148 Repeater CDMA-800 2 CH 115VAC, MRX, HP, RCUAR4545/00201 Repeater CDMA-800 4 CH 230VACAR4545/00202 Repeater CDMA-800 4 CH 230VAC, RCUAR4545/00203 Repeater CDMA-800 4 CH 21-60VDCAR4545/00204 Repeater CDMA-800 4 CH 21-60VDC, RCUAR4545/00207 Repeater CDMA-800 4 CH 115VACAR4545/00208 Repeater CDMA-800 4 CH 115VAC, RCU

AR4545/02241 Repeater CDMA-800 2+2 CH 230VACAR4545/02243 Repeater CDMA-800 2+2 CH 21-60VDCAR4545/02244 Repeater CDMA-800 2+2 CH 21-60VDC, RCUAR4545/02247 Repeater CDMA-800 2+2 CH 115VACAR4600/05201 Repeater BS 800 SMR IDEN 230VACAR4600/05203 Repeater BS 800 SMR IDEN 21-60VDCAR4600/05204 Repeater BS 800 SMR IDEN 21-60VDC, RCUAR4600/05207 Repeater BS 800 SMR IDEN 115VACAR6500/00101 Repeater W-CDMA 1-2 Ch 230VACAR6500/00102 Repeater W-CDMA 1-2 Ch 230VAC, RCUAR6500/00103 Repeater W-CDMA 1-2 Ch 21-60VDCAR6500/00104 Repeater W-CDMA 1-2 Ch 21-60VDC, RCUAR6560/00101 Repeater W-CDMA 1-2 Ch, HP 230VACAR6560/00102 Repeater W-CDMA 1-2 Ch, HP 230VAC, RCUAR6560/00103 Repeater W-CDMA 1-2 Ch, HP 21-60VDCAR6560/00104 Repeater W-CDMA 1-2 Ch, HP 21-60VDC, RCUAR6565/02201 Repeater W-CDMA 3-4 Ch 230VACAR6565/02202 Repeater W-CDMA 3-4 Ch 230VAC, RCUAR6565/02203 Repeater W-CDMA 3-4 Ch 21-60VDCAR6565/02204 Repeater W-CDMA 3-4 Ch 21-60VDC, RCUEA101 02/1 Software kit EnglishEA101 09/1 Weather Shield kitEA101 10/5 RCU Kit GSM-1900, WavecomEA101 10/6 RCU Kit GSM 900/1800, WavecomEA101 12/1 Door switch kitEA101 14/1 Expansion Kit 2->4 ch. 1900 MHzEA101 16/1 Expansion Kit 4->6 ch. 900 MHzEA101 19/1 Expansion Kit 2->4 ch. 1800 MHzEA101 20/1 Expansion Kit EGSM 2-4 chEA101 21/1 Expansion Kit EGSM 4-6 chEA101 22/1 Expansion Kit 900MHz 2-4chEA101 25/1 Expansion Kit AMPSEA101 31/1 Expansion Kit 4-8 ch. 900MHzEA101 32/1 Dual band Kit 900, adj 16.5 MHzEA101 33/1 Dual band Kit 1800, 2 ch. LBEA101 35/1 POI 900/1800 Kit, 1-port, N-typeEA101 35/2 POI 900/1800 Kit, 1-port, 7/16-typeEA101 36/1 POI 900/1800 Kit, 2-port, N-typeEA101 36/2 POI 900/1800 Kit, 2-port, 7/16-typeEA101 37/1 POI 800/1900 Kit, 1-port, N-typeEA101 37/2 POI 800/1900 Kit, 1-port, 7/16-type EA101 38/1 POI 800/1900 Kit, 2-port, N-typeEA101 38/2 POI 800/1900 Kit, 2-port, 7/16-typeEA101 39/1 Fiber Optic Installation KitEA101 43/1 Expansion Kit 4-8 ch. 1800MHzEA101 47/1 R2R-Kit InternalEA101 47/2 R2R-Kit ExternalEA101 48/1 Expansion Kit 4-6 ch. 1800MHzEA101 49/1 RCC KIT 900, WavecomEA101 50/1 RCC KIT 1800, WavecomEA101 52/1 RCC KIT 1900, WavecomEA101 54/1 Expansion Kit CDMA1900 MhzEA101 56/1 Dual band Kit BS 1800 MhzEA101 57/1 Pole mounting bracket for CompactEA101 58/1 Expansion Kit 4->6 ch 1900 MhzEA101 59/1 Repeater Tool Kit

EA101 60/1 Key Kit CompactEA101 61/1 Fiber Optic Maintenance KitEA101 63/1 RCU Kit CDMA 800, SierraEA101 64/1 RCU Kit CDMA 1900, SierraEA101 65/1 RCU Kit TDMA 800EA101 66/1 RCC Kit Wireline modemEA101 70/1 Expansion Kit WCDMA 1-2 CHEA101 73/1 Hinge kitEA101 74/1 RCC Kit TDMA 800EA101 75/1 RCC Kit CDMA 800EA101 75/3 RCC Kit CDMA 1900EA101 76/1 RCC Kit GSM 900/1800EA101 77/1 Expansion Kit Compact 1800, 15 MHzEA101 78/1 Expansion Kit Compact 900, 15 MHzEA101 78/2 Expansion Kit Compact 900, 25 MHzRL102 00/01 OMS Nokia Alarm Interface DemoRL102 01/01 OMS Nokia Alarm Interface Lic.RL104 00/01 OMS Single User, Demo VersionRL104 01/01 OMS Single User LicenseRL104 01/02 OMS Single User License Add.RL105 00/01 OMS Multi User, Demo VersionRL105 01/01 OMS Multi User License 5 usersRL105 01/02 OMS Multi User License Add.RS108/1 OMS Single User Ann. Sup. & UGRS108/2 OMS Single User Add. Sup. & UGRS108/3 OMS Multi User Ann. Sup. & UGRS108/4 OMS Multi User Add An Sup.& UGRS108/7 OMS Nokia Alarm In An Sup.& UGUA102 04/1 BBU 25Ah with 24VDC outputUA102 04/2 BBU 50Ah with 24VDC outputUA104 04/1 Solar Panel 1UA104 04/1 Solar Panel 2UA104 04/1 Solar Panel 3UA104 04/1 Solar Panel 4UA104 04/1 Solar Panel 5UA104 04/1 Solar Panel 6UA104 04/1 Solar Panel 7UA104 04/1 Solar Panel 8UA104 04/1 Solar Panel 9UA104 04/1 Solar Panel 10UA109 00/1 ACE FOUUA109 01/1-A FOU Type A, excl. repeaterUA109 01/1-B FOU Type B, excl. repeaterUA109 01/1-C FOU Type C, excl. repeaterUA109 01/1-D FOU Type D, excl. repeaterUA109 01/1-WA FOU Type A, WDM, excl. repeaterUA109 01/1-WB FOU Type B, WDM, excl. repeaterUA109 01/1-WC FOU Type C, WDM, excl. repeaterUA109 01/1-WD FOU Type D, WDM, excl. repeaterUA111 00/1 ACE BMUUA111 01/1-SS11L BMU. 1 LINE Star/Serial 1 FOT/FONUA111 01/1-SS22L BMU. 2 LINE Star/Serial 2 FOT/FONUA111 01/1-St12L BMU. 2 LINE Star 1 FOT/FONUA111 01/1-St13L BMU. 3 LINE Star 1 FOT/FONUA111 01/1-St14L BMU. 4 LINE Star 1 FOT/FONUA111 01/1-St23L BMU. 3 LINE Star 2 FOT/FON

UA111 01/1-St24L BMU. 4 LINE Star 2 FOT/FONUA111 01/1-St25L BMU. 5 LINE Star 2 FOT/FONUA111 01/1-St26L BMU. 6 LINE Star 2 FOT/FONUA111 01/1-St27L BMU. 7 LINE Star 2 FOT/FONUA111 01/1-St28L BMU. 8 LINE Star 2 FOT/FONUA111 01/1-WSS11LBMU. 1 LINE ,WDM Star/Serial 1 FOT/FONUA111 01/1-WSS22LBMU. 2 LINE, WDM Star/Serial 2 FOT/FONUA111 01/1-WSt12LBMU. 2 LINE, WDM Star 1 FOT/FONUA111 01/1-WSt13LBMU. 3 LINE, WDM Star 1 FOT/FONUA111 01/1-WSt14LBMU. 4 LINE, WDM Star 1 FOT/FONUA111 01/1-WSt23LBMU. 3 LINE, WDM Star 2 FOT/FONUA111 01/1-WSt24LBMU. 4 LINE, WDM Star 2 FOT/FONUA111 01/1-WSt25LBMU. 5 LINE, WDM Star 2 FOT/FONUA111 01/1-WSt26LBMU. 6 LINE, WDM Star 2 FOT/FONUA111 01/1-WSt27LBMU. 7 LINE, WDM Star 2 FOT/FONUA111 01/1-WSt28LBMU. 8 LINE, WDM Star 2 FOT/FONUA111 02/1 ACE BMU RackUA113 00/1 ACE RMUUA113 01/1-SS1L RMU. 1 LINE Star/SerialUA113 01/1-St2L RMU. 2 LINE Star UA113 01/1-St3L RMU. 3 LINE Star UA113 01/1-St4L RMU. 4 LINE Star UA113 01/1-WSS1LRMU. 1 LINE Star/Serial, WDMUA113 01/1-WSt2L RMU. 2 LINE Star, WDMUA113 01/1-WSt3L RMU. 3 LINE Star, WDMUA113 01/1-WSt4L RMU. 4 LINE Star, WDMUA115 00/1 Site Distribution UnitUA115 02/1 ACE SDU RackVE007 96/1 External R2R Cable for Compact VE008 17/1 BBU Compact Alarm Cable

Maritime Repeaters

Product Description ALM1200_00202 Compact 900 MHz ALM2200_00102 Compact 1800 MHz, Low Band ALM2200_90102 Compact 1800 MHz, High Band AM1200_05302 Standard 900 MHz AM2200_00102 Standard 1800 MHz, Low Band AM2200_90102 Standard 1800 MHz, High Band


Kjell Knuutinen

Dattum/Date

2003-06-16

Godkänd/Approved

Dok nr/Doc no

ALM1200/002-201

Rev

B

Sida/Page


Fil/file

ALM1200-002_B.doc

Ferry repeater with adjustable bandwidth

900 MHz version, 25 MHz BW Product Number: ALM1200/002

1. Electrical specification (typical values) The repeater complies with following standards:

- Radio Transmission and Reception ETS 300 609-4 - EMC for GSM and DCS repeaters ETS301 489-1 - EMC for Maritime applications EN60945 - Emission for Maritime applications BS1597 - Immunity for Maritime application BS7027

Frequency tuning band Up link 890 – 915 MHz Frequency tuning band Down link 935 – 960 MHz Filter bandwidth standard, adjustable 0.5 – 25 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Gain trail dynamic range 25 dB DL/UL gain trail tracking accuracy 2 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 25 dBm Output power, 2 carrier + 19 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W


Kjell Knuutinen

Dattum/Date

2003-06-16

Godkänd/Approved

Dok nr/Doc no

ALM1200/002-201

Rev

B

Sida/Page


Fil/file

ALM1200-002_B.doc



Kjell Knuutinen

Dattum/Date

2003-06-18

Godkänd/Approved

Dok nr/Doc no

ALM2200/001-201

Rev

B

Sida/Page


Fil/file

ALM2200-001_B.doc


1800 MHz version, Low band Product Number: ALM2200/001



Frequency tuning band Up link 1710 – 1765 MHz Frequency tuning band Down link 1805 – 1860 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 95 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55°C) 5 dB Gain step resolution 1 dB Gain trail dynamic range 25 dB DL/UL gain trail tracking accuracy 2 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 26 dBm Output power, 2 carrier + 20 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W


Kjell Knuutinen

Dattum/Date

2003-06-18

Godkänd/Approved

Dok nr/Doc no

ALM2200/001-201

Rev

B

Sida/Page


Fil/file

ALM2200-001_B.doc

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class NEMA4/IP65 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 4.3 Inches 385 x 385 x 110 mm Mechanical outline See Compact Low Weight < 22 lbs < 10 kg RF connectors N-type female Lock type Allgon Safety bolts


Kjell Knuutinen

Dattum/Date

2003-06-18

Godkänd/Approved

Dok nr/Doc no

ALM2200/901-201

Rev

B

Sida/Page


Fil/file

ALM2200-901_B.doc


1800 MHz version, High band Product Number: ALM2200/901





Kjell Knuutinen

Dattum/Date

2003-06-18

Godkänd/Approved

Dok nr/Doc no

ALM2200/901-201

Rev

B

Sida/Page


Fil/file

ALM2200-901_B.doc





Dok nr/Doc no

AM1200/053-201 Rev

D Sida/Page


Fil/file

AM1200_053_D.doc

Maritime repeater with adjustable bandwidth

900 MHz version Product Number: AM1200/053



Frequency tuning band Up link 890 – 915 MHz Frequency tuning band Down link 935– 960 MHz Filter bandwidth, software adjustable 0.5 – 25 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 45-85 dB Gain (max variation –25 to +55°C) 6 dB Gain step resolution 1 dB Gain trail dynamic range 30 dB DL/UL gain trail tracking accuracy 2 dB Selectivity BW 3 dB 25 MHz Selectivity BW 35 dB BW 3dB + 1.2 MHz Selectivity BW 45 dB BW 3dB + 2.2 MHz Output power, PEP + 29 dBm Output power, 2 carrier + 23 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 6 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage, default 230 VAC Power consumption 1 160 W

1 Repeater equipped with AC power supply must have power line filter EA101 84/2 and DC power supply must have power line filter EA101 84/3




Dok nr/Doc no

AM1200/053-201 Rev

D Sida/Page


Fil/file

AM1200_053_D.doc

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight < 46 lbs < 21 Kg RF connectors N-type female


Kjell Knuutinen

Dattum/Date

2003-06-16

Godkänd/Approved

Dok nr/Doc no

AM2200/001-201

Rev

C

Sida/Page


Fil/file

AM2200-001_C.doc


1800 MHz version, Low band Product Number: AM2200/001



Frequency tuning band Up link 1710 – 1765 MHz Frequency tuning band Down link 1805 – 1860 MHz Filter bandwidth, software adjustable 0.5 – 16,9 MHz Filter setting resolution 25 kHz Duplex spacing 95 MHz Gain adjustment range 45-85 dB Gain (max variation –25 to +55°C) 6 dB Gain step resolution 1 dB Gain trail dynamic range 30 dB DL/UL gain trail tracking accuracy 2 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 32 dBm Output power, 2 carrier + 26 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 6 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 1 85 - 265 VAC Power consumption 160 W



Kjell Knuutinen

Dattum/Date

2003-06-16

Godkänd/Approved

Dok nr/Doc no

AM2200/001-201

Rev

C

Sida/Page


Fil/file

AM2200-001_C.doc

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class NEMA4/IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight < 46 lbs < 21 kg RF connectors N-type female


Kjell Knuutinen

Dattum/Date

2003-06-16

Godkänd/Approved

Dok nr/Doc no

AM2200/901-201

Rev

C

Sida/Page


Fil/file

AM2200-901_C.doc


1800 MHz version, Upper band Product Number: AM2200/901



Frequency tuning band Up link 1730 – 1785 MHz Frequency tuning band Down link 1825 – 1880 MHz Filter bandwidth, software adjustable 0.5 – 16,9 MHz Filter setting resolution 25 kHz Duplex spacing 95 MHz Gain adjustment range 45-85 dB Gain (max variation –25 to +55°C) 6 dB Gain step resolution 1 dB Gain trail dynamic range 30 dB DL/UL gain trail tracking accuracy 2 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 32 dBm Output power, 2 carrier + 26 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 6 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 1 160 W



Kjell Knuutinen

Dattum/Date

2003-06-16

Godkänd/Approved

Dok nr/Doc no

AM2200/901-201

Rev

C

Sida/Page


Fil/file

AM2200-901_C.doc

2. Environmental specification Temperature range -25 to + 55 °C -13 to +131 °F Casing class NEMA4/IP65 3. Mechanical specification Dimensions. (W x H x D) 17.4 x 20.9 x 6.9 Inches 440 x 530 x 175 mm Mechanical outline See Standard Low Weight < 46 lbs < 21 kg RF connectors N-type female

In-train Repeaters

Product Description ALT1200_00202 Compact 900 MHz ALT2200_00102 Compact 1800 MHz, Low Band ALT2200_90102 Compact 1800 MHz, High Band


Kjell Knuutinen

Dattum/Date

2003-06-16

Godkänd/Approved

Dok nr/Doc no

ALT1200/002-201

Rev

B

Sida/Page


Fil/file

ALT1200-002_B.doc

In-Train repeater with adjustable bandwidth

900 MHz version, 25 MHz BW Product Number: ALT1200/002


- Radio Transmission and Reception ETS 300 609-4 - EMC for GSM and DCS repeaters ETS301 489-1 - EMC for railway applications-apparatus EN50121-3-2

Frequency tuning band Up link 890 – 915 MHz Frequency tuning band Down link 935 – 960 MHz Filter bandwidth standard, adjustable 0.5 – 25 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Gain trail dynamic range 25 dB DL/UL gain trail tracking accuracy 2 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 25 dBm Output power, 2 carrier + 19 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W


Kjell Knuutinen

Dattum/Date

2003-06-16

Godkänd/Approved

Dok nr/Doc no

ALT1200/002-201

Rev

B

Sida/Page


Fil/file

ALT1200-002_B.doc



Kjell Knuutinen

Dattum/Date

2003-06-16

Godkänd/Approved

Dok nr/Doc no

ALT2200/001-201

Rev

B

Sida/Page


Fil/file

ALT2200-001_B.doc


1800 MHz version, Low band Product Number: ALT2200/001





Kjell Knuutinen

Dattum/Date

2003-06-16

Godkänd/Approved

Dok nr/Doc no

ALT2200/001-201

Rev

B

Sida/Page


Fil/file

ALT2200-001_B.doc



Kjell Knuutinen

Dattum/Date

2003-06-16

Godkänd/Approved

Dok nr/Doc no

ALT2200/901-201

Rev

B

Sida/Page


Fil/file

ALT2200-901_B.doc


1800 MHz version, Upper band Product Number: ALT2200/901





Kjell Knuutinen

Dattum/Date

2003-06-16

Godkänd/Approved

Dok nr/Doc no

ALT2200/901-201

Rev

B

Sida/Page


Fil/file

ALT2200-901_B.doc



Kjell Knuutinen

Dattum/Date

2003-06-18

Godkänd/Approved

Dok nr/Doc no

ALR4200/011-201

Rev

G

Sida/Page


Fil/file

ALR4200-011_G.doc

COMPACT repeater with adjustable bandwidth 800 MHz version, CDMA, 15 MHz Product Number: ALR4200/011


Frequency tuning band Up link 824 – 849 MHz Frequency tuning band Down link 869 – 894 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power DL, RMS + 27 dBm Output power UL, RMS + 24 dBm Output power DL, 2 carrier + 23 dBm Output power UL, 2 carrier + 20 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure DL, at 70 dB gain, 25° C 6 dB Noise figure UL, at 70 dB gain, 25° C 5 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W

2. Environmental specification Temperature range -25 to + 55 °C -13 to + 131 °F Casing class NEMA4/IP65 3. Mechanical specification Dimensions. (W x H x D) 15.2 x 15.2 x 4.3 Inches 385 x 385 x 110 mm Mechanical outline See Compact Low Weight < 22 lbs < 10 kg RF-connectors N-type female Lock type Allgon Safety bolts


Kjell Knuutinen

Dattum/Date

2003-06-18

Godkänd/Approved

Dok nr/Doc no

ALR4200/012-201

Rev

F

Sida/Page


Fil/file

ALR4200-012_F.doc

COMPACT repeater with adjustable bandwidth 800 MHz version, CDMA 25 MHz Product Number: ALR4200/012


Frequency tuning band Up link 824 – 849 MHz Frequency tuning band Down link 869 – 894 MHz Filter bandwidth, software adjustable 0.5 – 25 MHz Filter setting resolution 25 kHz Duplex spacing 45 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power DL, RMS + 27 dBm Output power UL, RMS + 24 dBm Output power DL, 2 carrier + 23 dBm Output power UL, 2 carrier + 20 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure DL, at 70 dB gain, 25° C 6 dB Noise figure UL, at 70 dB gain, 25° C 4 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 – 265 VAC Power consumption 55 W



Kjell Knuutinen

Dattum/Date

2003-06-18

Godkänd/Approved

Dok nr/Doc no

ALR3200/011-201

Rev

C

Sida/Page


Fil/file

ALR3200-011_C.doc


1900 MHz version, CDMA Low band Product Number: ALR3200/011


Frequency tuning band Up link 1850 – 1890 MHz Frequency tuning band Down link 1930 – 1970 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 80 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 27 dBm Output power, RMS +24 dBm Output power, 2 carrier + 23 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W



Kjell Knuutinen

Dattum/Date

2003-06-18

Godkänd/Approved

Dok nr/Doc no

ALR3200/911-201

Rev

C

Sida/Page


Fil/file

ALR3200-911_C.doc


1900 MHz version, CDMA High band Product Number: ALR3200/911 1. Electrical specification (typical values) The repeater complies with the requirements of FCC

Frequency tuning band Up link 1870 – 1910 MHz Frequency tuning band Down link 1950 – 1990 MHz Filter bandwidth, software adjustable 0.5 – 15 MHz Filter setting resolution 25 kHz Duplex spacing 80 MHz Gain adjustment range 55-70 dB Gain (max variation –25 to +55 °C) 5 dB Gain step resolution 1 dB Filter selectivity @ 400 kHz offset > 20 dB Filter selectivity @ 600 kHz offset > 30 dB Filter selectivity @ 1 MHz offset > 35 dB Output power, PEP + 27 dBm Output power, RMS + 24 dBm Output power, 2 carrier + 23 dBm Pass band ripple 5 dB Max absolute group delay 6 µs Noise figure at 70 dB gain, 25° C 8 dB Maximum input power +13 dBm Receiver input port return loss 14 dB Power supply voltage 85 - 265 VAC Power consumption 55 W


Catalogo General de Repetidores

Documents

Transcript of Catalogo General de Repetidores