Catalog Rulmenti INA

732

Transcript of Catalog Rulmenti INA

PRODUCT REFERENCE GUIDECORPORATE OFFICES 308 SPRINGHILL FARM ROAD FORT MILL, SOUTH CAROLINA 29715 TELEPHONE (803)548-8500 FAX (803)548-8599 DISTRIBUTOR CUSTOMER SERVICE TOLL FREE 800-523-6572 FAX (803)548-8594

FOREWORDThis publication was designed to serve as a quick reference to the standard product series offered by INA USA Corporation (INA) for its domestic market. The guide provides a current overview of INA products, including basic envelope dimensions and capacities, in one publication it is not an engineering design guide intended to replace INA engineering catalogs. Consequently, the metric and inch conversions are listed to 3 decimal places for easy reference and rapid identification of correct replacement part(s), not 4 decimal places as necessary for quality control purposes. This publication can be used to narrow the choices between the many different INA product lines and series for new designs. Detailed engineering information for new designs can be found in our traditional catalogs or by contacting the INA Engineering Department. A significant portion of INA sales are special production sizes. The identification of those parts is sometimes difficult since a comprehensive listing is beyond the intent of this publication. Special part numbers take as many different forms as the series listed here, but the basic system is to use sequential numbers for each new design. Usually the prefix is F or FC but can include VH, INA or the bearing type such as NA. INA maintains a technical help desk to identify sizes not known or to match competitors parts. The toll free 800 numbers listed will give you access to INA Customer Service representatives. These representatives can tap into INA Worldwide resources to provide the bearings you need. Storage Life Lubricants age naturally due to environmental influences. It is therefore the users responsibility to follow the directions given by the lubricant manufacturer. The greases used in INA rolling bearings have a mineral oil base and experience shows that they can be stored for up to 3 years without deteriorating providing the following important conditions are met. D Closed storage room D Temperature between 0_C and 40_C D Relative atmospheric humidity 65% or less D Security from chemical agents (vapors, gases, fluids) D Sealed rolling bearings The frictional torque can be considerably higher after linger storage periods than in freshly greased bearings and the lubricity of the grease can also have deteriorated. INA bearings have many optional features available including: D ISO series of bearings generally include the standard clearance options CN, C2, C3 and C4. D ISO bearing series include PN, P6 and P5 precision classes. D Corrotectt plating is available for most bearing designs. Corrotect is a patented process for zinciron and zincironcobalt plating in a thin layer which can be applied to standard components. The protection exceeds stainless steel and the cost is half. Add suffix RR. D All sealed bearings are supplied pregreased. In most cases the standard lubricant is Shell Retinax LX 2 or equivalent. Other greases are available, some at extra cost. D Unsealed bearings may not be greased when shipped. D Speed limits as published, are based on oil lubrication for open bearings or grease lubrication for sealed bearings. The speed limits are calculated based on a nominal load and heat balance equation. Higher speeds may be allowed depending on the application. D Dynamic capacities are published based on INA standard usage of ISO and ABMA formulas. New life theory threshold values are published in other INA publications. D Life calculations and evaluations can be made from INA engineering based catalogs which are available from your INA Sales Representative. D Other features are available based on current production volumes including heat stabilization of the rings, matched bearing sets, with oil holes and grooves, etc.

ABMA ASTM DIN ISO

American Bearing Manufacturers Association American Society Of Testing And Materials Deutsches Institut fr Normung e.V. International Standards Organization

Elges, Andrews and Corrotect are registered trademarks of INA USA Corporation. Permaglide is a registered trademark and a product of KOLBENSCHMIDT AG, Neckarsulm, also produced in Greensburg, Indiana, USA. All other products and company names are trademarks or registered trademarks of their respective companies. ALL RIGHTS RESERVED INA USA Corporation 308 Springhill Farm Road Fort Mill, SC 29715 Reproduction of this publication in whole or in part without the express written consent of INA USA Corporation is prohibited. Although every effort has been made to ensure the accuracy of the information contained in this catalog, INA shall not be liable for any omissions or errors. Purchasers should consult their own testing to determine the suitability of any product for a particular purpose. In no event shall INA be liable for any claims for damages based upon breach of warranty, breach of contract, negligence, strict liability in tort, or any other legal theory.All sales from catalog orders are subject to the Standard Terms and Conditions of Sale. Please contact your INA Sales Representative for a copy of the Standard Terms and Conditions of Sale.

INA USA Corporation reserves the right to make changes / revisions to specifications contained herein without notice. ECopyright 1999, 2000, 2003 INA USA Corporation

Use of INA Part Numbers & SuffixesINA has extra options to give you the maximum flexibility in answering customer needs. Cage styles, seal types, internal clearances, and needle sorts are available to help you select the right part for your customers. UG - Shell type open bearings come standard without grease (Example: SCE87 UG) AA040 - Shell type sealed bearings come standard with 40% Retinax LX2 (Example: SCE8799 AA040) 0-7 - Radial needle roller & cage assemblies come standard with 0-7 Micron Needle Sorts (Example: NRA5X49.8G2 0-7, K25X33X24B 0-7)The table below provides a quick reference regarding our part numbers and integral suffixes. See each part section for part number schematics.PART / SUFFIX HK1010, SCE86PP 2RS 2Z J KDD, KDDU M NPP, NPPU PP RR TN X C2 C3 C4 AA040 UG 0-7 0-10 INA Part Number 2 Lip Seals 2 Gap Shields Steel Cage 2 Gap Shields Bronze Cage 2 Lip Seals 2 Lip Seals 2 Land Riding Seals Plastic Cage Cylindrical OD for Track Rollers Normal Clearance C2 Clearance C3 Clearance C4 Clearance 40% - Shell Retinax LX2 Ungreased / Corrosion Protected 0-7 Micron - Needle Sort 0-10 Micron - Needle Sort DEFINITION 62032RS, 3200J2RS 62032Z, 3300J2Z 52100J, 3200J LR5208KDD, LR5307KDDU 930M, 89460M GRA100NPPB, LR5202NPPU SCE87PP G1103KRRB, RA100RR 81102TN, 87410TN NATV20PPX, NUTR20X 6203, 62032RS 6302 C2, 63022Z C2 6205 C3, 62052RS C3 5305J C4, 6210 C4 HK1010 AA040 HK1010 UG NRA5X49.8G2 0-7, K25X33X24B 0-7 AXK6590 0-10 EXAMPLE SCE87, PASE1-1/2, RA100RR

PRODUCT REFERENCE GUIDENEEDLE BEARINGSPAGES 1-50

CAM FOLLOWERSPAGES 51-84

THRUST BEARINGSPAGES 85-178

RADIAL BALL BEARINGSPAGES 179-288

HIGH PRECISION BEARINGSPAGES 289-322

CYLINDRICAL ROLLER BEARINGSPAGES 323-344

ROLLER CLUTCHESPAGES 345-352

SEALS, SNAP RINGS & ROLLERSPAGES 353-370

PLAIN BEARINGS & ROD ENDSPAGES 371-444

LINEARPAGES 445-666

THIN SECTION, SLEWING RINGS & OTHER PRODUCTS PAGES 667-700

Section ContentsNEEDLE BEARINGS

BEARING SERIES INFORMATION P / N IDENTIFICATION HK BK SCE BCE SCH HK..2RS BK..RS SCH..PP BCH..P CSN SN S CS C K KBK KZK NAO NA49 NA69 NKI NKIS NA48 NA49..2RS RNAO NCS NK NKS RNA49 RNA69 RNA48 RNA49..2RS PNA RPNA IR LR PI

BEARING DESCRIPTION NEEDLE BEARING, GENERAL OVERVIEW NEEDLE BEARINGS OPEN END METRIC CAGED SHELL CLOSED END METRIC CAGED SHELL OPEN END INCH CAGED SHELL CLOSED END INCH CAGED SHELL OPEN END HEAVY INCH CAGED SHELL OPEN END SEALED METRIC CAGED SHELL CLOSED END SEALED METRIC CAGED SHELL OPEN END SEALED INCH CAGED SHELL CLOSED END SEALED INCH CAGED SHELL CLOSED END INCH GREASE RETAINED FULL COMPLEMENT SHELL OPEN END INCH GREASE RETAINED FULL COMPLEMENT SHELL OPEN END INCH MECHANICALLY RETAINED FULL COMPLEMENT SHELL CLOSED END INCH MECHANICALLY RETAINED FULL COMPLEMENT SHELL INCH CAGE AND ROLLER ASSEMBLIES METRIC CAGE AND ROLLER ASSEMBLIES WRIST PIN CAGE AND ROLLER ASSEMBLIES CRANK PIN CAGE AND ROLLER ASSEMBLIES METRIC SEPARABLE PRECISION GROUND NEEDLE METRIC ISO SERIES 49 PRECISION GROUND NEEDLE METRIC ISO SERIES 69 PRECISION GROUND NEEDLE METRIC SERIES NKI PRECISION GROUND NEEDLE METRIC SERIES NKIS PRECISION GROUND NEEDLE METRIC ISO SERIES 48 PRECISION GROUND NEEDLE METRIC ISO SERIES 49 SEALED PRECISION GROUND NEEDLE METRIC SEPARABLE PRECISION GROUND NEEDLE BEARINGS WITHOUT INNER INCH PRECISION GROUND NEEDLE BEARINGS WITHOUT INNER METRIC SERIES NKI PRECISION GROUND NEEDLE BEARINGS WITHOUT INNER METRIC SERIES NKIS PRECISION GROUND NEEDLE BEARINGS WITHOUT INNER METRIC ISO SERIES 49 PRECISION GROUND NEEDLE BEARINGS WITHOUT INNER METRIC ISO SERIES 69 PRECISION GROUND NEEDLE BEARINGS WITHOUT INNER METRIC ISO SERIES 48 PRECISION GROUND NEEDLE BEARINGS WITHOUT INNER METRIC ISO SERIES 49 SEALED PRECISION GROUND NEEDLE WITHOUT INNER METRIC ALIGNING PRECISION GROUND NEEDLE METRIC ALIGNING PRECISION GROUND NEEDLE BEARINGS WITHOUT INNER METRIC PRECISION GROUND NEEDLE BEARING INNER RINGS METRIC GROUND INNER RINGS INCH PRECISION GROUND NEEDLE BEARING INNER RINGS

PAGE 2 3 7 7 7 7 7 12 12 12 12 15 15 16 16 17 17 25 26 27 28 28 28 29 31 32 33 35 35 35 35 35 39 40 41 41 42 47 481

General InformationNEEDLE BEARINGS

PRODUCT DESCRIPTION INA Drawn Shell Needle Bearings D Deep Drawn Shell design for maximum capacity in the minimum radial space. D Cage guided needle rollers for low friction, whole roller loading and high speeds. D Available in standard inch and metric series with seals available as an option. D Available open for through shaft locations or with one end closed for shaft end locations to improve sealing. D Available in alternate design styles as full complement mechanically retained or full complement grease retained. D Easily mounted without snap rings or shoulders. INA Cage And Roller Assemblies D Combinations of needle rollers within various retainer designs for use with hardened shaft and housing. D Retainer guides needles providing full length roller contact for maximum capacity, low friction and long life. D Cages allow easy assembly compared to full sets of loose needles and adapt to higher misalignments. D Cages are available in various materials and designs as required by the applications, such as KZK and KBK for crankpin and wristpin locations. INA Precision Ground Needle Bearings D Through hardened machined and ground raceways with cage and roller complements. D Retainer guides needles providing full length roller contact for maximum capacity, low friction and long life. D Design series exist to match ISO, DIN, popular metric and inch dimension series. D Available with seals, higher precision or heat stabilization. D Location hole and groove in outer ring. INA Self Aligning Needle Bearings D Precision ground needle bearing with cage and roller complement. D Internal spherical seat to statically realign. D Allows for initial static misalignment up to 3_. D Plastic aligning seats and raceway are captured within a drawn shell for ease of assembly.

2

Part Number IdentificationNEEDLE BEARINGS

DRAWN SHELL NEEDLE BEARINGS INCH SERIES SCE, BCE, SCH, BCH, SN, CS, CSN METRIC SERIES HK, BK

HKPREFIX SCE BCE SCH BCH S Standard Series, Caged, Open End Standard Series, Caged, Closed End Heavy Series, Caged, Open End Heavy Series, Caged, Closed End Standard, Series, Full Complement, Mechanically Retained, Open End Standard Series, Full Complement, Grease Retained, Open End Standard Series, Full Complement, Mechanically Retained, Closed End Standard Series, Full Complement, Grease Retained, Closed End Metric Series, Caged, Open End Metric Series, Caged, Closed End

25Shaft Millimeters Sixteenths Of An Inch

20Width Millimeters Sixteenths Of An Inch

2RSSUFFIX RS 2RS P PP AS1 RR

AS1Seal, Metric 2 Seals, Metric Seal, Inch 2 Seals, Inch Oil Hole Corrotect Plated

SN

CS

CSN

HK BK

3

Part Number IdentificationNEEDLE BEARINGS

CAGE AND ROLLER ASSEMBLIES METRIC SERIES K, KZK, KBK

K

25 x 35 x 40Shaft In Millimeters Housing Bore In Millimeters Width In Millimeters

TNSUFFIX ZW AG A,B TN 2 Roller Rows Silver Plated Design Variation Plastic Cage

PREFIX K KZK KBK Metric Metric, Crank Metric, Wrist

UNIT CAGES INCH SERIES

CUNIT CAGE

32Shaft Sixteenths Of An Inch

38Housing Bore Sixteenths Of An Inch

16Width Sixteenths Of An Inch

RADIAL NEEDLE BEARINGS WITHOUT RIBS METRIC SERIES NAO, RNAO

NAOWith Inner Ring Without Inner Ring

25 x 35 x 4Shaft In Millimeters OD In Millimeters Width In Millimeters

TNSUFFIX TN Plastic Cage

PREFIX NAO RNAO

4

Part Number IdentificationNEEDLE BEARINGS

PRECISION GROUND NEEDLE BEARINGS METRIC ISO SERIES NA, RNA

NA48.. 49.. 69..

4914ISO Dimension Series ISO Dimension Series ISO Dimension Series

P6SUFFIX P. C. RR ISR

C3Precision Class Clearance Group Corrotect Plated Inner Ring Oil Groove & Hole Heat Stabilized

PREFIX NA RNA Metric Metric, No Inner Ring

..XX

ISO Definition Of Shaft Diameter

S.

PRECISION GROUND BEARINGS INCH SERIES NCS

NCSPrecision Ground Needle Bearing

12Shaft Sixteenths Of An Inch

12WIDTH Sixteenths Of An Inch

PRECISION GROUND RADIAL NEEDLE BEARING METRIC SERIES NK, NKS, NKI, NKIS

NK

35/30##/## Shaft / Width ## Shaft

TNTN Plastic Cage

NK NKS NKI NKIS

No Inner Ring, Light Series No Inner Ring, Heavy Series With Inner Ring, Light Series With Inner Ring, Heavy Series

5

Part Number IdentificationNEEDLE BEARINGS

ALIGNING NEEDLE ROLLER BEARINGS METRIC SERIES PNA, RPNA

RPNAPNA RPNA With Inner Ring Without Inner Ring

15 / 28Shaft In Millimeters OD In Millimeters

INNER RINGS INCH SERIES PI

PIPREFIX PI Inner Ring With Oil Groove

05Shaft Sixteenths Of An Inch

08OD Sixteenths Of An Inch

08Width Sixteenths Of An Inch

INNER RINGS METRIC SERIES IR, LR

IRIR LR Precision Ground For Precision Needle Bearings Precision Ground For Needle Bearings

05 x 08 x 08Shaft In Millimeters OD In Millimeters

ISIWidth In Millimeters SUFFIX ISI ISRI Oil Hole Oil Hole & Groove

PREFIX

6

Shell BearingsCAGE GUIDED NEEDLE ROLLER BEARING SERIESD D D D

Drawn cup Combined inch and metric sizes Open for through shafts Closed for shaft ends

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section. For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.PART NUMBER OPEN END PART NUMBER CLOSED END SHAFT Fw inch SHAFT Fw mm OD D inch OD D mm WIDTH C inch WIDTH C mm WGT. WGT.

SCE, SCH, HK

BCE, BCH, BK

DYN. CAP. C lbf

DYN. CAP. C N

STAT. CAP. C0 lbf

STAT. CAP. C0 N

SPEED LIMIT rpm

lbs

g

HK 0306 TN SCE24TN SCE21/24 SCE21/24TN HK 0408 SCE34TN SCE36TN SCE36 HK 0509 HK 0608 HK 0609 SCE44 SCE45 SCE47 HK 0709 SCE55 SCE57 SCE59 SCH57 HK 0808 HK 0810 HK 0908 HK 0910 HK 0912 SCE65 SCE66 SCE67 SCE68 SCE610 SCH68 HK 1010 HK 1012 HK 1015 SCE78 SCE710 SCH78 HK 1210 HK 1212 SCE85 SCE86 SCE87 SCE88 SCE810 SCE812 SCH87 SCH88

BK 0306 TN BCE24TN

0.118 0.125 0.156 0.156

3 3.175 3.969 3.969 4 4.762 4.762 4.762 5 6 6 6.350 6.350 6.350 7 7.938 7.938 7.938 7.938 8 8 9 9 9 9.525 9.525 9.525 9.525 9.525 9.525 10 10 10 11.112 11.112 11.112 12 12 12.700 12.700 12.700 12.700 12.700 12.700 12.700 12.700

0.256 0.250 0.281 0.281 0.315 0.344 0.344 0.344 0.354 0.394 0.394 0.437 0.437 0.437 0.433 0.500 0.500 0.500 0.563 0.472 0.472 0.512 0.512 0.512 0.563 0.563 0.563 0.563 0.563 0.625 0.551 0.551 0.551 0.625 0.625 0.688 0.630 0.709 0.687 0.687 0.687 0.687 0.687 0.687 0.750 0.750

6.5 6.350 7.145 7.145 8 8.731 8.731 8.731 9 10 10 11.112 11.112 11.112 11 12.700 12.700 12.700 14.288 12 12 13 13 13 14.288 14.288 14.288 14.288 14.288 15.875 14 14 14 15.875 15.875 17.462 16 18 17.462 17.462 17.462 17.462 17.462 17.462 19.050 19.050

0.236 0.250 0.250 0.250 0.315 0.250 0.375 0.375 0.354 0.315 0.354 0.250 0.313 0.437 0.354 0.313 0.437 0.563 0.437 0.315 0.394 0.315 0.394 0.472 0.313 0.375 0.437 0.500 0.625 0.500 0.394 0.472 0.591 0.500 0.625 0.500 0.394 0.472 0.313 0.375 0.437 0.500 0.625 0.750 0.438 0.500

6 6.350 6.350 6.350 8 6.350 9.525 9.530 9 8 9 6.350 7.938 11.112 9 7.938 11.112 14.288 11.112 8 10 8 10 12 7.938 9.525 11.112 12.700 15.875 12.700 10 12 15 12.700 15.875 12.700 10 12 7.938 9.525 11.112 12.700 15.875 19.050 11.112 12.700

0.002 0.003 0.003 0.003 0.004 0.003 0.004 0.004 0.004 0.005 0.006 0.005 0.006 0.009 0.006 0.008 0.013 0.014 0.015 0.006 0.007 0.007 0.009 0.01 0.007 0.009 0.011 0.013 0.015 0.020 0.009 0.011 0.013 0.016 0.020 0.020 0.01 0.02 0.009 0.011 0.013 0.016 0.021 0.025 0.020 0.022

1 1 1 1 2 1 2 2 2 2 3 2 3 4 3 4 6 6 7 3 3 3 4 5 3 4 5 6 7 9 4 5 6 7 9 9 5 9 4 5 6 7 9 11 9 10

275 240 285 275 400 400 620 630 540 455 640 360 570 920 700 650 1,060 1,340 1,070 620 850 870 960 1,190 650 870 980 1,300 1,660 1,590 990 1,240 1,530 1,430 1,830 1,760 1,110 1,460 820 1,040 1,330 1,550 1,980 2,230 1,650 1,910

1,230 1,070 1,260 1,230 1,780 1,790 2,750 2,800 2,400 2,030 2,850 1,600 2,500 4,000 3,100 2,900 4,700 6,000 4,750 2,750 3,800 3,850 4,250 5,300 2,900 3,900 4,350 5,800 7,400 7,100 4,400 5,500 6,800 6,400 8,100 7,900 4,950 6,500 3,650 4,600 5,900 6,900 8,800 9,900 7,340 8,500

189 165 211 204 295 305 530 550 445 370 590 260 470 870 660 590 1,090 1,480 930 590 890 930 1,050 1,420 610 890 1,030 1,490 2,040 1,590 1,150 1,530 1,980 1,760 2,400 1,840 1,390 1,640 890 1,210 1,660 2,030 2,750 3,200 1,760 2,120

840 740 940 910 1,310 1,360 2,350 2,440 1,990 1,650 2,600 1,200 2,090 3,850 2,950 2,600 4,850 6,600 4,100 2,600 3,950 4,150 4,650 6,300 2,700 3,950 4,600 6,600 9,000 7,100 5,100 6,800 8,800 7,800 10,700 8,200 6,200 7,300 3,950 5,400 7,400 9,000 12,300 14,300 7,800 9,400

46,000 31,500 25,000 25,000 41,000 21,000 21,000 21,000 38,000 35,000 35,000 44,000 44,000 44,000 31,000 35,500 35,500 35,500 35,500 28,000 28,000 25,000 25,000 25,000 29,500 29,500 29,500 29,500 29,500 29,500 23,000 23,000 23,000 25,000 25,000 25,000 20,000 19,000 22,000 22,000 22,000 22,000 22,000 22,000 22,000 22,000

BK 0408 BCE34TN BCE36TN BK 0509 BK 0609 BCE44 BCE45 BCE47 BK 0709 BCE55 BCE57 BCE59 BCH57 BK 0808 BK 0810 BK 0910 BK 0912 BCE65 BCE66 BCE67 BCE68 BCE610 BCH68 BK 1010 BK 1012 BK 1015 BCE78 BCH78 BK 1210 BK 1212 BCE85 BCE86 BCE87 BCE88 BCE810 BCE812 BCH87 BCH88

0.157 0.187 0.187 0.187 0.197 0.236 0.236 0.250 0.250 0.250 0.276 0.313 0.313 0.313 0.313 0.315 0.315 0.354 0.354 0.354 0.375 0.375 0.375 0.375 0.375 0.375 0.394 0.394 0.394 0.437 0.437 0.438 0.472 0.472 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.500

7

Shell BearingsCAGE GUIDED NEEDLE ROLLER BEARING SERIESD D D D

Drawn cup Combined inch and metric sizes Open for through shafts Closed for shaft ends

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section. For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.PART NUMBER OPEN END PART NUMBER CLOSED END SHAFT Fw inch SHAFT Fw mm OD D inch OD D mm WIDTH C inch WIDTH C mm WGT. WGT.

SCE, SCH, HK

BCE, BCH, BK

DYN. CAP. C lbf

DYN. CAP. C N

STAT. CAP. C0 lbf

STAT. CAP. C0 N

SPEED LIMIT rpm

lbs

g

SCH810 SCH812 HK 1312 HK 1412 SCE95 SCE96 SCE97 SCE98 SCE910 SCE912 SCH98 SCH910 SCH912 HK 1512 HK 1516 HK 1522 SCE105 SCE107 SCE1071/2 SCE108 SCE1010 SCE1012 SCH108 SCH1010 SCH1012 SCH1016 HK 1612 HK 1616 HK 1622 HK 1712 SCE116 SCE118 SCE1110 SCE1112 SCH117 SCH1110 SCH1112 HK 1812 HK 1816 SCE126 SCE128 SCE1210 SCE1212 SCH1212 HK 2010 HK 2012

BCH810 BCH812 BK 1312 BK 1412 BCE96 BCE98 BCE910 BCE912 BCH98 BCH910 BCH912 BK 1512 BK 1516 BK 1522 BCE105 BCE107 BCE1071/2 BCE108 BCE1010 BCE1012 BCH108 BCH1010 BCH1012 BCH1016 BK 1612 BK 1616 BK 1622 BK 1712 BCE118 BCE1110 BCE1112 BCH117 BCH1110 BCH1112 BK 1812 BK 1816 BCE126 BCE128 BCE1210 BCE1212 BCH1212 BK 2012

0.500 0.500 0.512 0.551 0.563 0.563 0.563 0.563 0.563 0.563 0.563 0.563 0.563 0.591 0.591 0.591 0.625 0.625 0.625 0.625 0.625 0.625 0.625 0.625 0.625 0.625 0.630 0.630 0.630 0.669 0.687 0.687 0.687 0.687 0.688 0.688 0.688 0.709 0.709 0.750 0.750 0.750 0.750 0.750 0.787 0.787

12.700 12.700 13 14 14.288 14.288 14.288 14.288 14.288 14.288 14.288 14.288 14.288 15 15 15 15.875 15.875 15.875 15.875 15.875 15.875 15.875 15.875 15.875 15.875 16 16 16 17 17.462 17.462 17.462 17.462 17.462 17.462 17.462 18 18 19.050 19.050 19.050 19.050 19.050 20 20

0.750 0.750 0.748 0.787 0.750 0.750 0.750 0.750 0.750 0.750 0.813 0.813 0.813 0.827 0.827 0.827 0.813 0.813 0.813 0.813 0.813 0.813 0.875 0.875 0.875 0.875 0.866 0.866 0.866 0.906 0.875 0.875 0.875 0.875 0.938 0.938 0.938 0.945 0.945 1.000 1.000 1.000 1.000 1.063 1.024 1.024

19.050 19.050 19 20 19.050 19.050 19.050 19.050 19.050 19.050 20.638 20.638 20.638 21 21 21 20.638 20.638 20.638 20.638 20.638 20.638 22.225 22.225 22.225 22.225 22 22 22 23 22.225 22.225 22.225 22.225 23.812 23.812 23.812 24 24 25.400 25.400 25.400 25.400 26.988 26 26

0.625 0.750 0.472 0.472 0.313 0.375 0.438 0.500 0.625 0.750 0.500 0.625 0.750 0.472 0.630 0.866 0.313 0.437 0.469 0.500 0.625 0.750 0.500 0.625 0.750 1.000 0.472 0.630 0.866 0.472 0.375 0.500 0.625 0.750 0.437 0.625 0.750 0.472 0.63 0.375 0.500 0.625 0.750 0.750 0.394 0.472

15.875 19.050 12 12 7.938 9.525 11.130 12.700 15.875 19.050 12.700 15.875 19.050 12 16 22 7.938 11.112 11.910 12.700 15.875 19.050 12.700 15.875 19.050 25.400 12 16 22 12 9.525 12.700 15.875 19.050 11.112 15.875 19.050 12 16 9.525 12.700 15.875 19.050 19.050 10 12

0.022 0.035 0.022 0.023 0.010 0.013 0.019 0.020 0.022 0.026 0.026 0.028 0.037 0.024 0.033 0.044 0.012 0.017 0.018 0.020 0.025 0.031 0.028 0.035 0.042 0.055 0.026 0.035 0.049 0.026 0.014 0.021 0.028 0.035 0.029 0.037 0.045 0.029 0.04 0.022 0.031 0.040 0.046 0.060 0.026 0.031

10 16 10 11 5 6 8 9 10 12 12 13 17 11 15 20 5 8 8 9 11 14 13 16 19 25 12 16 22 12 6 10 13 16 13 17 20 13 18 10 14 18 21 27 12 14

2,360 2,850 1,530 1,600 910 1,160 1,480 1,730 2,120 2,410 2,050 2,700 3,250 1,780 2,360 3,000 970 1,480 1,600 1,830 2,330 2,700 2,250 2,850 3,300 4,300 1,710 2,450 2,950 1,780 1,290 1,930 2,460 2,800 1,900 2,900 3,550 1,820 2,600 1,600 2,210 2,850 3,450 4,150 1,440 1,930

10,500 12,600 6,800 7,100 4,000 5,200 6,600 7,700 9,600 10,700 9,100 12,000 14,400 7,900 10,500 13,400 4,300 6,600 7,100 8,100 10,400 12,100 10,000 12,700 14,700 19,100 7,600 10,900 13,100 7,900 5,700 8,600 10,900 12,400 8,400 12,900 15,900 8,100 11,600 7,100 9,800 12,800 15,300 18,500 6,400 8,600

2,800 3,500 1,780 1,910 1,060 1,440 1,980 2,420 3,150 3,700 2,380 3,350 4,300 2,110 3,250 4,400 1,180 2,100 2,320 2,700 3,650 4,450 2,750 3,750 4,500 6,300 2,180 3,450 4,350 2,320 1,770 2,950 4,050 4,750 2,260 3,850 5,100 2,450 3,900 1,860 2,800 3,950 5,000 5,300 1,840 2,700

12,400 15,700 7,900 8,500 4,700 6,400 8,800 10,800 14,000 16,400 10,600 15,000 19,000 9,400 14,400 19,500 5,200 9,300 10,300 12,000 16,300 19,700 12,200 16,700 20,000 28,000 9,700 15,300 19,400 10,300 7,900 13,200 18,000 21,000 10,000 17,100 22,700 10,900 17,300 8,300 12,500 17,500 22,100 23,600 8,200 12,100

22,000 22,000 18,000 16,000 19,600 19,600 19,600 19,600 19,600 19,600 19,600 19,600 19,600 16,000 16,000 16,000 17,600 17,600 17,600 17,600 17,600 17,600 17,600 17,600 17,600 17,600 15,000 15,000 15,000 14,000 16,000 16,000 16,000 16,000 16,000 16,000 16,000 13,000 13,000 14,700 14,700 14,700 14,700 14,700 12,000 12,000

8

Shell BearingsCAGE GUIDED NEEDLE ROLLER BEARING SERIESD D D D

Drawn cup Combined inch and metric sizes Open for through shafts Closed for shaft ends

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section. For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.PART NUMBER OPEN END PART NUMBER CLOSED END SHAFT Fw inch SHAFT Fw mm OD D inch OD D mm WIDTH C inch WIDTH C mm WGT. WGT.

SCE, SCH, HK

BCE, BCH, BK

DYN. CAP. C lbf

DYN. CAP. C N

STAT. CAP. C0 lbf

STAT. CAP. C0 N

SPEED LIMIT rpm

lbs

g

HK 2016 HK 2020 HK 2030 SCE136 SCE138 SCE1312 SCE1314 SCH1310 SCH1312 HK 22x28x7.5 TN HK 2210 HK 2212 HK 2216 HK 2220 SCE146 SCE148 SCE1412 SCE1416 SCH1412 SCH1416 SCE1516 HK 24x30x7.5 TN HK 2512 HK 2516 HK 2520 HK 2526 HK 2538 SCE166 SCE168 SCE1612 SCE1616 SCH1610 SCH1612 SCH1616 HK 2816 HK 2820 SCE186 SCE188 SCE1812 SCE1816 SCH1810 SCH1812 SCH1816 SCH1818 SCH1820 HK 3012

BK 2016 BK 2020 BK 2030 BCE138 BCE1312 BCH1310 BCH1312

0.787 0.787 0.787 0.813 0.813 0.813 0.813 0.813 0.813 0.866 0.866

20 20 20 20.638 20.638 20.638 20.638 20.638 20.638 22 22 22 22 22 22.225 22.225 22.225 22.225 22.225 22.225 23.812 24 25 25 25 25 25 25.400 25.400 25.400 25.400 25.400 25.400 25.400 28 28 28.575 28.575 28.575 28.575 28.575 28.575 28.575 28.575 28.575 30

1.024 1.024 1.024 1.063 1.063 1.063 1.063 1.125 1.125 1.102 1.102 1.102 1.102 1.102 1.125 1.125 1.125 1.125 1.188 1.188 1.187 1.181 1.260 1.260 1.260 1.260 1.260 1.250 1.250 1.250 1.250 1.313 1.313 1.313 1.378 1.378 1.375 1.375 1.375 1.375 1.500 1.500 1.500 1.500 1.500 1.457

26 26 26 26.988 26.988 26.988 26.988 28.575 28.575 28 28 28 28 28 28.575 28.575 28.575 28.575 30.162 30.162 30.162 30 32 32 32 32 32 31.750 31.750 31.750 31.750 33.338 33.338 33.338 35 35 34.925 34.925 34.925 34.925 38.100 38.100 38.100 38.100 38.100 37

0.630 0.787 1.181 0.375 0.500 0.750 0.875 0.625 0.750 0.295 0.394 0.472 0.630 0.787 0.375 0.500 0.750 1.000 0.750 1.000 1.000 0.295 0.472 0.630 0.787 1.024 1.496 0.375 0.500 0.750 1.000 0.625 0.750 1.000 0.630 0.787 0.375 0.500 0.750 1.000 0.625 0.750 1.000 1.125 1.250 0.472

16 20 30 9.525 12.700 19.050 22.225 15.875 19.050 7.5 10 12 16 20 9.525 12.700 19.050 25.400 19.050 25.400 25.400 7.5 12 16 20 26 38 9.525 12.700 19.050 25.400 15.875 19.050 25.400 16 20 9.525 12.700 19.050 25.400 15.875 19.050 25.400 28.580 31.750 12

0.042 0.053 0.077 0.031 0.035 0.053 0.060 0.055 0.066 0.02 0.029 0.033 0.046 0.057 0.029 0.042 0.061 0.075 0.070 0.094 0.084 0.022 0.044 0.06 0.073 0.097 0.141 0.040 0.042 0.060 0.084 0.077 0.080 0.105 0.064 0.079 0.042 0.045 0.066 0.088 0.094 0.105 0.138 0.186 0.121 0.051

19 24 35 14 16 24 27 25 30 9 13 15 21 26 13 19 28 34 32 43 38 10 20 27 33 44 64 18 19 27 38 35 36 47 29 36 19 21 30 40 43 48 63 85 55 23

2,850 3,550 4,900 1,590 2,420 3,600 4,150 3,550 4,350 1,300 1,690 2,050 3,000 3,700 1,850 2,500 3,800 4,950 4,400 5,800 5,400 1,370 2,470 3,500 4,450 5,700 7,600 1,750 2,850 4,150 5,600 3,750 4,500 6,500 3,700 4,700 1,870 2,900 4,250 5,800 4,900 5,700 7,100 9,100 9,200 2,700

12,700 15,700 21,800 7,100 10,800 15,900 18,500 15,900 19,200 5,800 7,500 9,100 13,400 16,500 8,200 11,200 16,900 22,100 19,500 25,500 24,100 6,100 11,000 15,600 19,900 25,500 34,000 7,800 12,600 18,500 24,800 16,700 20,000 28,900 16,400 20,900 8,300 12,800 18,900 26,000 21,800 25,000 31,500 40,500 40,900 12,100

4,500 5,800 9,000 1,880 3,200 5,300 6,500 4,650 6,000 1,710 2,360 3,000 4,950 6,500 2,400 3,550 6,100 8,500 6,100 8,600 9,700 1,840 3,400 5,400 7,400 10,100 14,800 2,300 4,300 7,000 10,200 5,100 6,400 10,400 6,000 8,100 2,600 4,550 7,700 11,100 6,500 7,800 10,600 14,500 14,600 4,100

20,100 26,000 40,000 8,400 14,300 23,700 29,000 20,700 26,500 7,600 10,500 13,400 22,100 29,000 10,700 15,800 27,000 38,000 27,000 38,500 43,000 8,200 15,200 24,000 33,000 45,000 66,000 10,200 19,100 31,500 45,500 22,700 28,500 46,300 26,500 36,000 11,500 20,200 34,000 49,500 29,000 35,000 46,500 65,000 64,500 18,200

12,000 12,000 12,000 13,600 13,600 13,600 13,600 13,600 13,600 11,000 11,000 11,000 11,000 11,000 12,600 12,600 12,600 12,600 12,600 12,600 11,800 10,000 10,000 10,000 10,000 10,000 10,000 11,000 11,000 11,000 11,000 11,000 11,000 11,000 9,000 9,000 9,800 9,800 9,800 9,800 9,800 9,800 9,800 9,800 9,800 8,500

BK 2212 BK 2216 BK 2220 BCE146 BCE148 BCE1412 BCE1416 BCH1412 BCH1416 BCE1516 BK 2512 BK 2516 BK 2520 BK 2526 BK 2538 BCE166 BCE168 BCE1612 BCE1616 BCH1610 BCH1612 BCH1616 BK 2816 BK 2820 BCE186 BCE188 BCE1812 BCE1816 BCH1810 BCH1812 BCH1816 BCH1818 BCH1820 BK 3012

0.866 0.866 0.866 0.875 0.875 0.875 0.875 0.875 0.875 0.937 0.945 0.984 0.984 0.984 0.984 0.984 1.000 1.000 1.000 1.000 1.000 1.000 1.000 1.102 1.102 1.125 1.125 1.125 1.125 1.125 1.125 1.125 1.125 1.125 1.181

9

Shell BearingsCAGE GUIDED NEEDLE ROLLER BEARING SERIESD D D D

Drawn cup Combined inch and metric sizes Open for through shafts Closed for shaft ends

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section. For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.PART NUMBER OPEN END PART NUMBER CLOSED END SHAFT Fw inch SHAFT Fw mm OD D inch OD D mm WIDTH C inch WIDTH C mm WGT. WGT.

SCE, SCH, HK

BCE, BCH, BK

DYN. CAP. C lbf

DYN. CAP. C N

STAT. CAP. C0 lbf

STAT. CAP. C0 N

SPEED LIMIT rpm

lbs

g

HK 3016 HK 3020 HK 3026 HK 3038 SCE1916 SCE208 SCE2010 SCE2012 SCE2016 SCE2020 SCH208 SCH2012 SCH2016 SCH2020 HK 32x39x24 SCE2110 SCE228 SCE2212 SCE2216 SCE2220 SCH2212 SCH2216 HK 3512 HK 3516 HK 3520 SCE248 SCE2410 SCE2412 SCE2414 SCE2416 SCE2420 HK 4012 HK 4016 HK 4020 SCE2610 SCE2620 SCE2812 SCE2816 SCE2820 SCE2824 HK 4512 HK 4516 HK 4520 HK 50x57x16 HK 5020 HK 5025

BK 3016 BK 3020 BK 3026 BK 3038 BCE208 BCE2010 BCE2012 BCE2016 BCE2020 BCH208 BCH2012 BCH2016 BCH2020

1.181 1.181 1.181 1.181 1.187 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.250 1.260 1.313

30 30 30 30 30.162 31.750 31.750 31.750 31.750 31.750 31.750 31.750 31.750 31.750 32 33.338 34.925 34.925 34.925 34.925 34.925 34.925 35 35 35 38.100 38.100 38.100 38.100 38.100 38.100 40 40 40 41.275 41.275 44.450 44.450 44.450 44.450 45 45 45 50 50 50

1.457 1.457 1.457 1.457 1.500 1.500 1.500 1.500 1.500 1.500 1.625 1.625 1.625 1.625 1.535 1.625 1.625 1.625 1.625 1.625 1.750 1.750 1.654 1.654 1.654 1.875 1.875 1.875 1.875 1.875 1.875 1.850 1.850 1.850 2.000 2.000 2.125 2.125 2.125 2.125 2.047 2.047 2.047 2.244 2.283 2.283

37 37 37 37 38.100 38.100 38.100 38.100 38.100 38.100 41.275 41.275 41.275 41.275 39 41.275 41.275 41.275 41.275 41.275 44.450 44.450 42 42 42 47.625 47.625 47.625 47.625 47.625 47.625 47 47 47 50.800 50.800 53.975 53.975 53.975 53.975 52 52 52 57 58 58

0.630 0.787 1.024 1.496 1.000 0.500 0.625 0.750 1.000 1.250 0.500 0.750 1.000 1.250 0.945 0.625 0.500 0.750 1.000 1.250 0.750 1.000 0.472 0.630 0.787 0.500 0.625 0.750 0.875 1.000 1.250 0.472 0.630 0.787 0.625 1.250 0.750 1.000 1.250 1.500 0.472 0.630 0.787 0.630 0.787 0.984

16 20 26 38 25.400 12.700 15.875 19.050 25.400 31.750 12.700 19.050 25.400 31.750 24 15.875 12.700 19.050 25.400 31.750 19.050 25.400 12 16 20 12.700 15.875 19.050 22.225 25.400 31.750 12 16 20 15.875 31.750 19.050 25.400 31.750 38.100 12 16 20 16 20 25

0.068 0.086 0.112 0.168 0.095 0.049 0.066 0.082 0.099 0.123 0.079 0.137 0.157 0.174 0.11 0.082 0.055 0.086 0.128 0.179 0.127 0.170 0.06 0.079 0.097 0.106 0.119 0.137 0.159 0.183 0.232 0.066 0.086 0.119 0.121 0.243 0.181 0.254 0.295 0.359 0.073 0.101 0.123 0.11 0.154 0.198

31 39 51 76 43 22 30 37 45 56 36 62 71 79 50 37 25 39 58 81 57 77 27 36 44 48 54 62 72 83 105 30 39 54 55 110 82 115 134 163 33 46 56 50 70 90

3,850 4,950 6,300 8,400 7,400 3,000 3,700 4,750 6,100 7,500 3,700 6,100 8,100 9,800 6,200 4,750 3,050 4,800 6,200 7,600 6,600 8,800 2,950 4,200 5,400 4,200 5,500 6,800 8,100 8,700 10,600 3,150 4,500 5,700 5,700 11,400 7,100 9,300 12,400 14,000 3,350 4,800 6,100 4,100 7,000 8,700

17,200 22,000 28,000 37,500 33,000 13,500 16,500 21,100 27,000 33,500 16,400 27,100 36,000 43,600 27,500 21,100 13,600 21,500 27,500 34,000 29,500 39,000 13,100 18,700 23,800 18,600 24,400 30,500 36,000 38,500 47,500 14,000 20,000 25,500 25,500 51,000 31,500 41,500 55,000 62,000 14,900 21,300 27,000 18,200 31,000 38,500

6,500 8,900 12,100 17,800 12,900 4,950 6,500 8,900 12,300 16,100 4,700 8,900 12,900 16,400 12,100 7,600 5,300 9,600 13,300 17,300 10,100 14,700 4,800 7,500 10,300 5,800 8,300 10,900 13,500 14,900 19,200 5,500 8,700 11,700 8,900 21,900 12,300 17,000 24,300 29,000 6,200 9,700 13,300 8,200 14,200 18,900

29,000 39,500 54,000 79,000 57,000 22,200 29,000 39,500 55,000 71,000 21,000 39,500 57,500 72,900 54,000 34,000 23,700 42,500 59,000 77,000 45,000 65,000 21,300 33,500 46,000 26,000 36,500 48,500 60,000 66,000 86,000 24,300 38,500 52,000 40,000 97,000 55,000 76,000 108,000 130,000 27,500 43,000 59,000 36,500 63,000 84,000

8,500 8,500 8,500 8,500 9,300 8,800 8,800 8,800 8,800 8,800 8,800 8,800 8,800 8,800 8,000 8,400 8,000 8,000 8,000 8,000 8,000 8,000 7,500 7,500 7,500 7,400 7,400 7,400 7,400 7,400 7,400 6,500 6,500 6,500 6,800 6,800 6,300 6,300 6,300 6,300 6,000 6,000 6,000 5,000 5,000 5,000

BCE228 BCE2212 BCE2220 BCH2212 BCH2216 BK 3512 BK 3516 BK 3520 BCE248 BCE2410 BCE2412 BCE2414 BCE2416 BCE2420 BK 4012 BK 4016 BK 4020 BCE2610 BCE2620 BCE2812 BCE2816 BCE2824 BK 4516 BK 4520 BK 5020 BK 5025

1.375 1.375 1.375 1.375 1.375 1.375 1.378 1.378 1.378 1.500 1.500 1.500 1.500 1.500 1.500 1.575 1.575 1.575 1.625 1.625 1.750 1.750 1.750 1.750 1.772 1.772 1.772 1.969 1.969 1.969

10

Shell BearingsCAGE GUIDED NEEDLE ROLLER BEARING SERIESD D D D

Drawn cup Combined inch and metric sizes Open for through shafts Closed for shaft ends

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section. For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.PART NUMBER OPEN END PART NUMBER CLOSED END SHAFT Fw inch SHAFT Fw mm OD D inch OD D mm WIDTH C inch WIDTH C mm WGT. WGT.

SCE, SCH, HK

BCE, BCH, BK

DYN. CAP. C lbf

DYN. CAP. C N

STAT. CAP. C0 lbf

STAT. CAP. C0 N

SPEED LIMIT rpm

lbs

g

SCE328 SCE3210 SCE3216 SCE3220 SCE348 SCE3410 SCE3416 HK 5520 HK 5528 SCE3612 SCE3616 HK 6012 HK 6020 HK 6032 SCE4412 SCE5612 BK 5520 BK 5528 BCE3612 BCE3616 BK 6012 BK 6020 BK 6032 BCE4412 BCE3410 BCE3216

2.000 2.000 2.000 2.000 2.125 2.125 2.125 2.165 2.165 2.250 2.250 2.362 2.362 2.362 2.750 3.500

50.800 50.800 50.800 50.800 53.975 53.975 53.975 55 55 57.150 57.150 60 60 60 69.850 88.900

2.375 2.375 2.375 2.375 2.500 2.500 2.500 2.480 2.480 2.625 2.625 2.677 2.677 2.677 3.125 4.000

60.325 60.325 60.325 60.325 63.500 63.500 63.500 63 63 66.675 66.675 68 68 68 79.375 101.600

0.500 0.625 1.000 1.250 0.500 0.625 1.000 0.787 1.102 0.750 1.000 0.472 0.787 1.260 0.750 0.750

12.700 15.875 25.400 31.750 12.700 15.875 25.400 20 28 19.050 25.400 12 20 32 19.050 19.050

0.128 0.150 0.225 0.304 0.137 0.159 0.256 0.163 0.232 0.196 0.265 0.108 0.179 0.3 0.291 0.410

58 68 102 138 62 72 116 74 105 89 120 49 81 136 132 186

4,900 6,400 9,300 12,400 5,200 7,000 11,200 7,100 9,900 8,400 11,300 3,900 7,500 11,900 8,800 11,900

21,800 28,500 41,500 55,000 5,200 31,000 50,000 31,500 44,000 37,500 50,000 17,400 33,500 53,000 38,500 53,000

7,900 11,200 17,900 26,000 8,700 12,700 23,200 15,100 23,200 16,200 24,000 7,200 16,900 30,500 18,300 23,200

35,000 49,500 80,000 116,000 39,000 57,000 103,000 67,000 103,000 72,000 107,000 32,000 75,000 135,000 80,000 103,000

5,500 5,500 5,500 5,500 5,200 5,200 5,200 4,700 4,700 4,900 4,900 4,400 4,400 4,400 4,000 3,150

11

Shell BearingsSEALED SERIESD Drawn cup caged needle bearings D Open and closed, single or double sealed

SCE..PP, SCH..PP, HK..2RS

SCE..P, SCH..P, HK..RS

BCE..P, BCH..P, BK..RS

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section. For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.PART NUMBER 2 SEALS PART NUMBER 1 SEAL PART NUMBER 1 SEAL CLOSED END SHAFT Fw inch SHAFT Fw mm OD D inch OD D mm WIDTH C inch WIDTH C mm WGT. WGT. DYN. CAP. C lbf DYN. CAP. C N STAT. CAP. C0 lbf STAT. CAP. C0 N SPEED LIMIT rpm

lbs

g

SCE45P SCE46PP SCE46P SCE47PP SCE48P SCE49PP SCE56P SCE57PP SCE58P SCE59PPR SCH58P HK 0810 RS HK 0812.2RS SCE66P SCE67PP SCE68PP SCE69P SCE610PP HK 1012 RS HK 1014.2RS SCH79P SCH710PP HK 1214 RS HK 1216.2RS SCE86P SCE87PP SCE89P SCE810PP SCE812PP SCH813PR SCH814PPR HK 1414 RS HK 1416.2RS SCE99P SCE910PP SCE912PP SCH910PR SCH913P HK 1514 RS HK 1516.2RS HK 1518 RS HK 1520.2RS SCE109P SCE1010PP SCE1011P SCE1012PP BCH910PR BCH913P BK 1514 RS BK 1414 RS BCH813P BCE89P BCH79P BCE69P BCE66P BCH58P BCE58P BCE48P

0.250 0.250 0.250 0.250 0.250 0.250 0.313 0.313 0.313 0.313 0.313 0.315 0.315 0.375 0.375 0.375 0.375 0.375 0.394 0.394 0.438 0.438 0.472 0.472 0.500 0.500 0.500 0.500 0.500 0.500 0.500 0.551 0.551 0.563 0.563 0.563 0.563 0.563 0.591 0.591 0.591 0.591 0.625 0.625 0.625 0.625

6.350 6.350 6.350 6.350 6.350 6.350 7.938 7.938 7.938 7.938 7.938 8 8 9.525 9.525 9.525 9.525 9.525 10 10 11.112 11.112 12 12 12.700 12.700 12.700 12.700 12.700 12.700 12.700 14 14 14.288 14.288 14.288 14.288 14.288 15 15 15 15 15.875 15.875 15.875 15.875

0.438 0.438 0.438 0.438 0.438 0.438 0.500 0.500 0.500 0.500 0.563 0.472 0.472 0.563 0.563 0.563 0.563 0.563 0.551 0.551 0.688 0.688 0.709 0.709 0.688 0.688 0.688 0.688 0.688 0.750 0.750 0.787 0.787 0.750 0.750 0.750 0.813 0.813 0.827 0.827 0.827 0.827 0.813 0.813 0.813 0.813

11.112 11.112 11.112 11.112 11.112 11.112 12.700 12.700 12.700 12.700 14.288 12 12 14.288 14.288 14.288 14.288 14.288 14 14 17.462 17.462 18 18 17.462 17.462 17.462 17.462 17.462 19.050 19.050 20 20 19.050 19.050 19.050 20.638 20.638 21 21 21 21 20.638 20.638 20.638 20.638

0.313 0.375 0.375 0.438 0.500 0.563 0.375 0.438 0.500 0.563 0.500 0.394 0.472 0.375 0.438 0.500 0.563 0.625 0.472 0.551 0.563 0.625 0.551 0.630 0.375 0.438 0.563 0.625 0.750 0.813 0.875 0.551 0.630 0.563 0.625 0.750 0.625 0.813 0.551 0.630 0.709 0.787 0.563 0.625 0.687 0.750

7.938 9.525 9.525 11.112 12.700 14.288 9.525 11.112 12.700 14.288 12.700 10 12 9.525 11.112 12.700 14.288 15.875 12 14 14.288 15.875 14 16 9.525 11.112 14.288 15.875 19.050 20.638 22.225 14 16 14.288 15.875 19.050 15.875 20.638 14 16 18 20 14.288 15.875 17.460 19.050

0.007 0.010 0.010 0.009 0.009 0.011 0.009 0.008 0.013 0.011 0.009 0.007 0.007 0.011 0.026 0.013 0.015 0.015 0.009 0.010 0.020 0.024 0.022 0.024 0.020 0.013 0.022 0.022 0.030 0.037 0.026 0.026 0.029 0.026 0.029 0.027 0.022 0.042 0.026 0.033 0.035 0.040 0.022 0.022 0.026 0.029

3 5 5 4 4 5 4 4 6 5 4 3 3 5 12 6 7 7 4 5 9 11 10 11 9 6 10 10 14 17 12 12 13 12 13 12 10 19 12 15 16 18 10 10 12 13

360 360 570 570 920 920 650 650 1,060 1,060 1,170 620 620 650 650 870 1,300 1,300 990 990 1,780 1,780 1,460 1,460 820 820 1,550 1,550 1,980 2,850 2,850 1,600 1,600 1,730 1,730 2,120 2,450 3,250 1,750 1,750 2,360 2,360 1,830 1,830 2,330 2,330

1,600 1,600 2,500 2,500 4,000 4,000 2,900 2,900 4,700 4,700 5,200 2,750 2,750 2,900 2,900 3,900 5,800 5,800 4,400 4,400 7,900 7,900 6,500 6,500 3,650 3,650 6,900 6,900 8,800 12,600 12,600 7,100 7,100 7,700 7,700 9,600 10,900 14,400 7,800 7,800 10,500 10,500 8,100 8,100 10,400 10,400

260 260 470 470 870 870 590 590 1,090 1,090 1,080 590 590 610 610 890 1,490 1,490 1,150 1,150 1,840 1,840 1,640 1,640 890 890 2,030 2,030 2,750 3,550 3,550 1,910 1,910 2,420 2,420 3,150 3,000 4,250 2,200 2,200 3,250 3,250 2,700 2,700 3,650 3,650

1,200 1,200 2,090 2,090 3,850 3,850 2,600 2,600 4,850 4,850 4,800 2,600 2,600 2,700 2,700 3,950 6,600 6,600 5,100 5,100 8,200 8,200 7,300 7,300 3,950 3,950 9,000 9,000 12,300 15,700 15,700 8,500 8,500 10,800 10,800 14,000 13,300 19,000 9,800 9,800 14,400 14,400 12,000 12,000 16,300 16,300

27,000 27,000 27,000 27,000 27,000 27,000 23,000 23,000 23,000 23,000 21,000 20,000 20,000 20,000 20,000 20,000 20,000 20,000 17,000 17,000 15,000 15,000 14,000 14,000 15,000 15,000 15,000 15,000 15,000 14,000 14,000 12,000 12,000 14,000 14,000 14,000 12,000 12,000 11,000 11,000 11,000 11,000 13,000 13,000 13,000 13,000

12

Shell BearingsSEALED SERIESD Drawn cup caged needle bearings D Open and closed, single or double sealed

SCE..PP, SCH..PP, HK..2RS

SCE..P, SCH..P, HK..RS

BCE..P, BCH..P, BK..RS

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section. For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.PART NUMBER 2 SEALS PART NUMBER 1 SEAL PART NUMBER 1 SEAL CLOSED END SHAFT Fw inch SHAFT Fw mm OD D inch OD D mm WIDTH C inch WIDTH C mm WGT. WGT. DYN. CAP. C lbf DYN. CAP. C N STAT. CAP. C0 lbf STAT. CAP. C0 N SPEED LIMIT rpm

lbs

g

SCE1014PP HK 1614 RS HK 1616.2RS HK 1620.2RS BCH06604PK BCH06604PR SCH06604PR HK 1814 RS HK 1816.2RS SCE128PP SCE129P SCE1210PP SCE1211P SCE1212PP SCE1214PPR HK 2016.2RS HK 2018 RS HK 2020.2RS HK 2214 RS HK 2216.2RS HK 2218 RS HK 2220.2RS SCE148PP SCE1414PP SCH1413P SCH1414PP HK 2516.2RS HK 2518 RS HK 2520.2RS HK 2524.2RS HK 2530.2RS SCE1616PP SCH1613P SCH1614P SCH1616PP HK 2820.2RS HK 3016.2RS HK 3018 RS HK 3020.2RS HK 3024.2RS SCE2012P SCE2014PR SCE2016PPR SCH2018P SCH2020PP BCH2212PV BCH1614P BK 2518 RS BCH1413P BK 2018 RS BCE1211P BCE129P BK 1614 RS

0.625 0.630 0.630 0.630 0.670 0.670 0.670 0.709 0.709 0.750 0.750 0.750 0.750 0.750 0.750 0.787 0.787 0.787 0.866 0.866 0.866 0.866 0.875 0.875 0.875 0.875 0.984 0.984 0.984 0.984 0.984 1.000 1.000 1.000 1.000 1.102 1.181 1.181 1.181 1.181 1.250 1.250 1.250 1.250 1.250 1.375

15.875 16 16 16 17.015 17.015 17.015 18 18 19.050 19.050 19.050 19.050 19.050 19.050 20 20 20 22 22 22 22 22.225 22.225 22.225 22.225 25 25 25 25 25 25.400 25.400 25.400 25.400 28 30 30 30 30 31.750 31.750 31.750 31.750 31.750 34.925

0.813 0.866 0.866 0.866 0.938 0.938 0.939 0.945 0.945 1.000 1.000 1.000 1.000 1.000 1.000 1.024 1.024 1.024 1.102 1.102 1.102 1.102 1.125 1.125 1.188 1.188 1.260 1.260 1.260 1.260 1.260 1.250 1.313 1.313 1.313 1.378 1.457 1.457 1.457 1.457 1.500 1.500 1.500 1.625 1.625 1.750

20.638 22 22 22 23.813 23.813 23.838 24 24 25.400 25.400 25.400 25.400 25.400 25.400 26 26 26 28 28 28 28 28.575 28.575 30.162 30.162 32 32 32 32 32 31.750 33.338 33.338 33.338 35 37 37 37 37 38.100 38.100 38.100 41.275 41.275 44.450

0.875 0.551 0.630 0.787 0.688 0.688 0.688 0.551 0.630 0.438 0.563 0.625 0.687 0.750 0.875 0.630 0.709 0.787 0.551 0.630 0.709 0.787 0.500 0.875 0.813 0.875 0.630 0.709 0.787 0.945 1.181 1.000 0.813 0.875 1.000 0.787 0.630 0.709 0.787 0.945 0.750 0.875 1.000 1.125 1.250 0.750

22.225 14 16 20 17.480 17.480 17.480 14 16 11.112 14.288 15.875 17.460 19.050 22.225 16 18 20 14 16 18 20 12.700 22.225 20.638 22.225 16 18 20 24 30 25.400 20.638 22.225 25.400 20 16 18 20 24 19.050 22.225 25.400 28.580 31.750 19.050

0.033 0.029 0.031 0.040 0.037 0.037 0.029 0.031 0.033 0.029 0.037 0.036 0.049 0.045 0.056 0.040 0.046 0.051 0.035 0.040 0.053 0.057 0.035 0.066 0.075 0.060 0.060 0.064 0.068 0.088 0.104 0.073 0.079 0.086 0.095 0.075 0.068 0.082 0.079 0.097 0.079 0.084 0.108 0.168 0.192 0.099

15 13 14 18 17 17 13 14 15 13 17 17 22 20 25 18 21 23 16 18 24 26 16 30 34 27 27 29 31 40 47 33 36 39 43 34 31 37 36 44 36 38 49 76 87 45

2,700 1,710 1,710 2,450 1,660 1,660 1,660 1,820 1,820 1,600 2,210 2,210 2,850 2,850 3,450 1,930 2,850 2,850 2,050 2,050 3,000 3,000 1,850 3,800 4,400 4,050 2,470 3,500 3,500 4,450 5,700 4,050 4,150 4,500 4,500 3,700 2,700 3,850 3,850 4,950 3,650 4,750 4,750 8,200 7,400 5,600

12,100 7,600 7,600 10,900 7,400 7,400 7,400 8,100 8,100 7,100 9,800 9,800 12,800 12,800 15,300 8,600 12,700 12,700 9,100 9,100 13,400 13,400 8,200 16,900 19,500 18,100 11,000 15,600 15,600 19,900 25,500 18,000 18,500 20,000 20,000 16,400 12,100 17,200 17,200 22,000 16,300 21,100 21,100 36,500 33,000 25,000

4,450 2,180 2,180 3,450 1,800 1,800 1,800 2,450 2,450 1,860 2,800 2,800 3,950 3,950 5,000 2,700 4,500 4,500 3,000 3,000 4,950 4,950 2,400 6,100 6,100 6,100 3,400 5,400 5,400 7,400 10,100 6,800 6,400 6,400 6,400 6,000 4,100 6,500 6,500 8,900 6,400 8,900 8,900 13,000 12,800 9,100

19,700 9,700 9,700 15,300 8,000 8,000 8,000 10,900 10,900 8,300 12,500 12,500 17,500 17,500 22,100 12,100 20,100 20,100 13,400 13,400 22,100 22,100 10,700 27,000 27,000 27,000 15,200 24,000 24,000 33,000 45,000 30,000 28,500 28,500 28,500 26,500 18,200 29,000 29,000 39,500 28,500 39,500 39,500 58,000 57,000 40,500

13,000 11,000 11,000 11,000 11,000 11,000 11,000 9,500 9,500 10,000 10,000 10,000 10,000 10,000 10,000 8,500 8,500 8,500 8,000 8,000 8,000 8,000 9,000 9,000 8,000 8,000 7,000 7,000 7,000 7,000 7,000 8,000 7,000 7,000 7,000 6,000 6,000 6,000 6,000 6,000 6,500 6,500 6,500 6,000 6,000 6,000

13

Shell BearingsSEALED SERIESD Drawn cup caged needle bearings D Open and closed, single or double sealed

SCE..PP, SCH..PP, HK..2RS

SCE..P, SCH..P, HK..RS

BCE..P, BCH..P, BK..RS

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section. For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.PART NUMBER 2 SEALS PART NUMBER 1 SEAL PART NUMBER 1 SEAL CLOSED END SHAFT Fw inch SHAFT Fw mm OD D inch OD D mm WIDTH C inch WIDTH C mm WGT. WGT. DYN. CAP. C lbf DYN. CAP. C N STAT. CAP. C0 lbf STAT. CAP. C0 N SPEED LIMIT rpm

lbs

g

HK 3516.2RS HK 3518 RS HK 3520.2RS SCE2414P SCE2416P SCE2422P SCE2424PP HK 4016.2RS HK 4018 RS HK 4020.2RS HK 4518 RS HK 4520.2RS HK 5022 RS HK 5024.2RS

1.378 1.378 1.378 1.500 1.500 1.500 1.500 1.575 1.575 1.575 1.772 1.772 1.969 1.969

35 35 35 38.100 38.100 38.100 38.100 40 40 40 45 45 50 50

1.654 1.654 1.654 1.875 1.875 1.875 1.875 1.850 1.850 1.850 2.047 2.047 2.284 2.284

42 42 42 47.625 47.625 47.625 47.625 47 47 47 52 52 58 58

0.630 0.709 0.787 0.875 1.000 1.375 1.500 0.630 0.709 0.787 0.709 0.787 0.866 0.945

16 18 20 22.225 25.400 34.920 38.100 16 18 20 18 20 22 24

0.071 0.086 0.090 0.155 0.183 0.243 0.258 0.082 0.099 0.106 0.110 0.119 0.168 0.179

32 39 41 70 83 110 117 37 45 48 50 54 76 81

2,950 4,200 4,200 6,900 8,100 10,600 10,600 3,150 4,500 4,500 4,800 4,800 7,000 7,000

13,100 18,700 18,700 30,500 36,000 47,000 47,000 14,000 20,000 20,000 21,300 21,300 31,000 31,000

4,800 7,500 7,500 11,100 13,700 19,200 19,200 5,500 8,700 8,700 9,700 9,700 14,200 14,200

21,300 33,500 33,500 49,500 61,000 19,464 19,464 24,300 38,500 38,500 43,000 43,000 63,000 63,000

5,000 5,000 5,000 5,500 5,500 5,500 5,500 4,500 4,500 4,500 4,000 4,000 3,600 3,600

14

Shell BearingsCSN, SN, SNH SERIESD Full complement grease retained series D Drawn cup needle rollers D Open and closed end designs

CSN, CSNH

SN, SNH

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section. For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.PART NUMBER SHAFT Fw inch SHAFT Fw mm OD D inch OD D mm WIDTH C inch WIDTH C mm WGT. WGT. DYN. CAP. C lbf DYN. CAP. C N STAT. CAP. C0 lbf STAT. CAP. C0 N SPEED LIMIT rpm

lbs

g

SN45 SN55 SN56 SN57 SN65 CSN66 SN66 SN68 SN76 SN78 SN88 SN810 SN812 SNH87 SN105 SN116 SN128 SN148 SN1816 CSN2816

0.250 0.313 0.313 0.313 0.375 0.375 0.375 0.375 0.438 0.438 0.500 0.500 0.500 0.500 0.625 0.688 0.750 0.875 1.125 1.750

6.350 7.938 7.938 7.938 9.525 9.525 9.525 9.525 11.112 11.112 12.700 12.700 12.700 12.700 15.875 17.462 19.050 22.225 28.575 44.450

0.438 0.500 0.500 0.500 0.563 0.563 0.563 0.563 0.625 0.625 0.688 0.688 0.688 0.750 0.813 0.875 1.000 1.125 1.375 2.125

11.112 12.700 12.700 12.700 14.288 14.288 14.288 14.288 15.875 15.875 17.462 17.462 17.462 19.050 20.638 22.225 25.400 28.575 34.925 53.975

0.313 0.313 0.375 0.438 0.313 0.500 0.375 0.500 0.375 0.500 0.500 0.625 0.750 0.438 0.313 0.375 0.500 0.500 1.000 1.000

7.938 7.938 9.525 11.113 7.938 12.700 9.525 12.700 9.525 12.700 12.700 15.875 19.050 11.112 7.938 9.525 12.700 12.700 25.400 25.400

0.007 0.009 0.011 0.011 0.010 0.008 0.008 0.015 0.020 0.018 0.020 0.024 0.031 0.024 0.015 0.019 0.037 0.040 0.130 0.269

3 4 5 5 5 4 4 7 9 8 9 11 14 11 7 9 17 18 59 122

980 1,260 1,370 1,620 1,390 1,550 1,300 1,730 1,710 2,230 2,650 2,900 3,600 2,110 1,440 2,090 3,350 3,900 8,200 13,300

4,350 5,600 6,100 7,200 6,200 6,900 5,800 7,700 7,600 9,900 11,800 12,900 15,900 9,400 6,400 9,300 15,000 17,400 36,500 59,000

1,100 1,390 1,980 2,200 1,660 2,090 1,190 1,730 2,470 3,600 4,150 5,300 6,600 1,960 1,510 3,850 5,600 7,100 20,200 30,500

4,900 6,200 8,800 9,800 7,400 9,300 5,300 7,700 11,000 16,000 18,400 23,600 29,500 8,700 6,700 17,100 25,000 31,500 90,000 136,000

10,000 8,300 8,300 8,300 7,100 7,100 7,100 7,100 6,300 6,300 5,600 5,600 5,600 5,300 4,550 4,200 3,750 3,250 2,600 1,660

15

Full Complement Shell BearingsMECHANICALLY RETAINED SERIESD Drawn cup D Open or closed end

S, SH

CS, CSH

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section. For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.PART NUMBER SHAFT Fw inch SHAFT Fw mm OD D inch OD D mm WIDTH C inch WIDTH C mm WGT. lbs WGT. g DYN. CAP. C lbf DYN. CAP. C N STAT. CAP. C0 lbf STAT. CAP. C0 N SPEED LIMIT rpm

S44 S45 S55 S57 CS59 S66 S78 S810 S85 S88 S98 S1012 S108 S116 S1110 S1112 S1210 CS1210 S1212 S128 S1316 CS1316 S138 S1412 S148 CS1516 S1612 S168 SH1612 SH1616 S1710 S1812 S2012 S2016 S2212 S2220 S2416 S2610 S268 S2812 S2824 S3016 S308 S3216 S3624 S4216

0.250 0.250 0.313 0.313 0.313 0.375 0.438 0.500 0.500 0.500 0.563 0.625 0.625 0.688 0.688 0.688 0.750 0.750 0.750 0.750 0.813 0.813 0.813 0.875 0.875 0.938 1.000 1.000 1.000 1.000 1.063 1.125 1.250 1.250 1.375 1.375 1.500 1.625 1.625 1.750 1.750 1.875 1.875 2.000 2.250 2.625

6.350 6.350 7.938 7.938 7.938 9.525 11.112 12.700 12.700 12.700 14.288 15.875 15.875 17.462 17.463 17.463 19.050 19.050 19.050 19.050 20.638 20.638 20.638 22.225 22.225 23.812 25.400 25.400 25.400 25.400 26.988 28.575 31.750 31.750 34.925 34.925 38.100 41.275 41.275 44.450 44.450 47.625 47.625 50.800 57.150 66.675

0.438 0.438 0.500 0.500 0.500 0.563 0.625 0.688 0.688 0.688 0.750 0.813 0.813 0.875 0.875 0.875 1.000 1.000 1.000 1.000 1.063 1.063 1.063 1.125 1.125 1.188 1.250 1.250 1.314 1.314 1.313 1.375 1.500 1.500 1.625 1.625 1.875 2.000 2.000 2.125 2.125 2.250 2.250 2.375 2.625 3.000

11.112 11.112 12.700 12.700 12.700 14.288 15.875 17.462 17.462 17.462 19.050 20.638 20.638 22.225 22.225 22.225 25.400 25.400 25.400 25.400 26.988 26.988 26.988 28.575 28.575 30.162 31.750 31.750 33.380 33.380 33.338 34.925 38.100 38.100 41.275 41.275 47.625 50.800 50.800 53.975 53.975 57.150 57.150 60.325 66.675 76.200

0.250 0.313 0.313 0.438 0.563 0.375 0.500 0.625 0.313 0.500 0.500 0.750 0.500 0.375 0.625 0.750 0.625 0.625 0.750 0.500 1.000 1.000 0.500 0.750 0.500 1.000 0.750 0.500 0.750 1.000 0.625 0.750 0.750 1.000 0.750 1.250 1.000 0.625 0.500 0.750 1.500 1.000 0.500 1.000 1.500 1.000

6.350 7.938 7.938 11.112 14.288 9.525 12.700 15.875 7.938 12.700 12.700 19.050 12.700 9.525 15.880 19.050 15.875 15.875 19.050 12.700 25.400 25.400 12.700 19.050 12.700 25.400 19.050 12.700 19.050 25.400 15.875 19.050 19.050 25.400 19.050 31.750 25.400 15.875 12.700 19.050 38.100 25.400 12.700 25.400 38.100 25.400

0.004 0.007 0.007 0.011 0.015 0.011 0.018 0.024 0.021 0.020 0.020 0.035 0.022 0.020 0.031 0.037 0.044 0.044 0.055 0.035 0.079 0.079 0.040 0.064 0.040 0.084 0.071 0.044 0.088 0.108 0.062 0.079 0.086 0.117 0.095 0.159 0.207 0.130 0.088 0.175 0.375 0.256 0.115 0.267 0.084 0.353

2 3 3 5 7 5 8 11 10 9 9 16 10 9 14 17 20 20 25 16 36 36 18 29 18 38 32 20 40 49 28 36 39 53 43 72 94 59 40 80 170 116 52 121 38 160

600 820 940 1,420 1,870 1,300 2,230 2,700 1,370 2,180 2,300 3,650 2,450 2,050 3,200 3,850 4,000 4,000 4,800 3,200 7,300 7,300 3,000 5,000 3,650 7,500 5,500 3,600 6,900 8,900 4,750 6,500 6,300 8,200 6,400 10,300 10,700 6,500 7,300 8,100 18,900 13,500 5,700 12,400 19,600 14,400

2650 3650 4200 6300 8300 5800 9900 12000 6100 9700 10230 16300 10900 9100 14200 17100 17700 17700 21350 14300 32500 32500 13400 22300 16300 33500 24600 15900 30500 39500 21100 29000 28000 36500 28500 46000 47500 29000 32500 36000 84000 60000 25500 55000 87000 64000

570 880 1,100 1,870 2,700 1,780 3,150 4,850 1,780 3,650 4,050 7,600 4,550 3,250 6,700 8,400 7,000 7,000 8,900 5,200 13,700 13,700 4,900 8,800 5,800 14,800 11,900 6,700 11,100 15,700 9,900 13,300 14,800 20,900 16,000 30,000 2,410 12,400 12,400 16,900 44,000 28,500 9,600 30,500 56,000 40,000

2550 3900 4900 8300 11900 7900 14100 21600 7900 16300 18014 34000 20300 14400 30000 37500 31000 31000 39500 23100 61000 61000 21700 39000 26000 66000 53000 30000 49500 70000 44000 59000 66000 93000 71000 133000 10700 55000 55000 75000 196000 126000 42500 136000 250000 177000

15,000 15,000 12,500 12,500 12,500 10,700 9,400 8,300 8,400 8,400 7,500 6,800 6,800 6,300 6,300 6,300 5,600 5,600 5,600 5,600 5,200 5,200 5,200 4,900 4,900 4,600 4,300 4,300 4,250 4,250 4,100 3,900 3,500 3,500 3,200 3,200 2,850 2,650 2,650 2,490 2,490 2,340 2,340 2,200 1,970 1,700

16

Needle Roller And Cage AssembliesUNIT CAGE SERIESD Inch and metric D Single and double row

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section. For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.PART NUMBER SHAFT Fw inch SHAFT Fw mm HSG. BORE Ew inch HSG. BORE Ew mm WIDTH Bc inch WIDTH Bc mm WGT. WGT. DYN. CAP. C lbf DYN. CAP. C N STAT. CAP. C0 lbf STAT. CAP. C0 N SPEED LIMIT rpm

lbs

g

K 3x5x7 TN K 3x5x9 TN K 3x6x7 TN K 4x7x7 TN K 4x7x10 TN K 5x8x8 TN K 5x8x10 TN K 6x9x8 TN K 6x9x10 TN K 6x10x13 TN K 7x9x7 TN K 7x10x8 TN K 7x10x10 TN K 8x11x8 TN K 8x11x10 TN K 8x11x13 TN K 8x12x8 K 8x12x10 TN K 9x12x10 TN K 9x12x13 TN C060806 K 10x13x10 TN K 10x13x13 TN K 10x13x16 TN K 10x14x10 TN K 10x14x13 TN K 10x16x12 TN K 12x15x10 TN K 12x15x13 TN K 12x15x20 ZW TN K 12x16x10 K 12x16x13 TN K 12x17x13 TN K 12x18x12 TN C081008 K 14x17x10 K 14x17x17 TN K 14x18x10 K 14x18x13 K 14x18x14 K 14x18x15 TN K 14x18x17 K 14x20x12 C091108 C091110 K 15x18x17 TN

0.118 0.118 0.118 0.158 0.158 0.197 0.197 0.236 0.236 0.236 0.276 0.276 0.276 0.315 0.315 0.315 0.315 0.315 0.354 0.354 0.375 0.394 0.394 0.394 0.394 0.394 0.394 0.472 0.472 0.472 0.472 0.472 0.472 0.472 0.500 0.551 0.551 0.551 0.551 0.551 0.551 0.551 0.551 0.563 0.563 0.591

3 3 3 4 4 5 5 6 6 6 7 7 7 8 8 8 8 8 9 9 9.525 10 10 10 10 10 10 12 12 12 12 12 12 12 12.700 14 14 14 14 14 14 14 14 14.288 14.288 15

0.197 0.197 0.236 0.276 0.276 0.315 0.315 0.354 0.354 0.394 0.354 0.394 0.394 0.433 0.433 0.433 0.472 0.472 0.472 0.472 0.500 0.512 0.512 0.512 0.551 0.551 0.630 0.591 0.591 0.591 0.630 0.630 0.669 0.709 0.625 0.669 0.669 0.709 0.709 0.709 0.709 0.709 0.787 0.688 0.688 0.709

5 5 6 7 7 8 8 9 9 10 9 10 10 11 11 11 12 12 12 12 12.700 13 13 13 14 14 16 15 15 15 16 16 17 18 15.875 17 17 18 18 18 18 18 20 17.463 17.463 18

0.276 0.354 0.276 0.276 0.394 0.315 0.394 0.315 0.394 0.512 0.276 0.315 0.394 0.315 0.394 0.512 0.315 0.394 0.394 0.512 0.375 0.394 0.512 0.630 0.394 0.512 0.472 0.394 0.512 0.787 0.394 0.512 0.512 0.472 0.500 0.394 0.669 0.394 0.512 0.551 0.591 0.669 0.472 0.500 0.625 0.669

7 9 7 7 10 8 10 8 10 13 7 8 10 8 10 13 8 10 10 13 9.525 10 13 16 10 13 12 10 13 20 10 13 13 12 12.700 10 17 10 13 14 15 17 12 12.700 15.875 17

0.001 0.001 0.001 0.001 0.002 0.002 0.002 0.002 0.002 0.004 0.001 0.002 0.002 0.002 0.003 0.004 0.001 0.004 0.003 0.005 0.005 0.004 0.005 0.006 0.006 0.01 0.012 0.006 0.005 0.011 0.008 0.012 0.011 0.013 0.009 0.009 0.009 0.009 0.014 0.013 0.011 0.018 0.019 0.010 0.013 0.01

0.3 0.4 0.4 0.5 0.7 0.7 0.9 0.8 1.1 1.9 0.6 0.9 1 1 1.2 1.7 0.4 2 1.5 2.1 2.5 1.6 2.3 2.9 2.5 4.6 5.5 2.9 2.3 5 3.7 5.5 4.9 6 4.2 4 4 4 6.5 6 5 8 8.5 4.7 5.9 4.6

345 385 320 390 520 530 670 590 750 850 405 640 820 700 890 1,150 800 1,120 1,010 1,330 900 1,070 1,390 1,600 1,300 1,690 1,820 1,100 1,440 1,890 1,440 1,800 2,160 2,250 1,490 1,190 2,050 1,600 1,840 2,140 2,140 2,430 2,320 1,630 2,190 1,800

1540 1710 1430 1740 2330 2350 3000 2600 3350 3800 1810 2850 3650 3100 3950 5100 3550 5000 4500 5900 4000 4750 6200 7100 5800 7500 8100 4900 6400 8400 6400 8000 9600 10000 6600 5300 9100 7100 8200 9500 9500 10800 10300 7300 9800 8000

290 335 218 285 415 430 600 510 710 700 425 600 810 670 920 1,300 690 1,060 1,120 1,600 940 1,240 1,750 2,090 1,350 1,890 1,620 1,370 1,910 2,750 1,620 2,110 2,340 2,230 1,960 1,600 3,150 1,910 2,270 2,750 2,750 3,250 2,380 2,290 3,350 2,700

1290 1480 970 1270 1840 1920 2650 2280 3150 3100 1880 2650 3600 3000 4100 5800 3050 4700 5000 7100 4200 5500 7800 9300 6000 8400 7200 6100 8500 12200 7200 9400 10400 9900 8700 7100 14100 8500 10100 12300 12300 14400 10600 10200 15000 12100

50,000 50,000 47,000 43,000 43,000 39,000 39,000 37,000 37,000 35,000 35,000 34,000 34,000 32,000 32,000 32,000 32,000 32,000 31,000 31,000 30,000 29,000 29,000 29,000 29,000 29,000 28,000 27,000 27,000 27,000 27,000 27,000 26,000 26,000 26,000 25,000 25,000 25,000 25,000 25,000 25,000 25,000 24,000 25,000 25,000 25,000

17

Needle Roller And Cage AssembliesUNIT CAGE SERIESD Inch and metric D Single and double row

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section. For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.PART NUMBER SHAFT Fw inch SHAFT Fw mm HSG. BORE Ew inch HSG. BORE Ew mm WIDTH Bc inch WIDTH Bc mm WGT. WGT. DYN. CAP. C lbf DYN. CAP. C N STAT. CAP. C0 lbf STAT. CAP. C0 N SPEED LIMIT rpm

lbs

g

K 15x19x10 K 15x19x13 K 15x19x17 K 15x20x13 K 15x21x15 K 15x21x21 C101208 K 16x20x10 K 16x20x13 K 16x20x17 K 16x22x12 K 16x22x13 K 16x22x16 K 16x22x20 K 16x24x20 K 17x21x10 K 17x21x13 K 17x21x17 K 18x22x10 K 18x22x13 K 18x22x17 K 18x24x12 K 18x24x13 K 18x24x20 K 18x25x14 K 18x25x22 K 18x28x16 K 19x23x13 K 19x23x17 C121616 K 20x24x10 K 20x24x12 K 20x24x13 K 20x24x17 K 20x26x12 K 20x26x13 K 20x26x17 K 20x26x20 K 20x28x16 K 20x28x20 K 20x28x25 K 20x30x30 C131608 C131714 K 21x25x13 K 21x25x17

0.591 0.591 0.591 0.591 0.591 0.591 0.625 0.630 0.630 0.630 0.630 0.630 0.630 0.630 0.630 0.669 0.669 0.669 0.709 0.709 0.709 0.709 0.709 0.709 0.709 0.709 0.709 0.748 0.748 0.750 0.787 0.787 0.787 0.787 0.787 0.787 0.787 0.787 0.787 0.787 0.787 0.787 0.813 0.813 0.827 0.827

15 15 15 15 15 15 15.875 16 16 16 16 16 16 16 16 17 17 17 18 18 18 18 18 18 18 18 18 19 19 19.050 20 20 20 20 20 20 20 20 20 20 20 20 20.638 20.638 21 21

0.748 0.748 0.748 0.787 0.827 0.827 0.750 0.787 0.787 0.787 0.866 0.866 0.866 0.866 0.945 0.827 0.827 0.827 0.866 0.866 0.866 0.945 0.945 0.945 0.984 0.984 1.102 0.906 0.906 1.000 0.945 0.945 0.945 0.945 1.024 1.024 1.024 1.024 1.102 1.102 1.102 1.181 1.000 1.063 0.984 0.984

19 19 19 20 21 21 19.050 20 20 20 22 22 22 22 24 21 21 21 22 22 22 24 24 24 25 25 28 23 23 25.400 24 24 24 24 26 26 26 26 28 28 28 30 25.400 26.988 25 25

0.394 0.512 0.669 0.512 0.591 0.827 0.500 0.394 0.512 0.669 0.472 0.512 0.630 0.787 0.787 0.394 0.512 0.669 0.394 0.512 0.669 0.472 0.512 0.787 0.551 0.866 0.630 0.512 0.669 1.000 0.394 0.472 0.512 0.669 0.472 0.512 0.669 0.787 0.630 0.787 0.984 1.181 0.500 0.875 0.512 0.669

10 13 17 13 15 21 12.700 10 13 17 12 13 16 20 20 10 13 17 10 13 17 12 13 20 14 22 16 13 17 25.400 10 12 13 17 12 13 17 20 16 20 25 30 12.700 22.230 13 17

0.011 0.015 0.021 0.015 0.024 0.037 0.011 0.012 0.017 0.022 0.022 0.026 0.026 0.037 0.049 0.012 0.014 0.021 0.013 0.018 0.024 0.026 0.029 0.04 0.033 0.051 0.053 0.018 0.024 0.058 0.014 0.018 0.02 0.026 0.024 0.026 0.035 0.042 0.044 0.06 0.071 0.108 0.023 0.054 0.02 0.022

5 7 9.5 7 11 17 5.2 5.5 7.5 10 10 12 12 17 22 5.5 6.5 9.5 6 8 11 12 13 18 15 23 24 8 11 26.4 6.5 8 9 12 11 12 16 19 20 27 32 49 10.2 24.7 9 10

1,690 1,910 2,550 2,230 3,200 4,350 1,840 1,750 2,000 2,650 2,600 2,800 3,350 4,100 4,800 1,820 2,340 2,750 1,890 2,070 2,700 2,650 2,950 4,550 3,800 5,200 4,400 2,140 2,800 5,600 2,000 2,200 2,200 2,900 3,000 3,250 4,300 4,750 4,450 5,400 6,900 8,000 2,800 5,100 2,270 3,000

7500 8500 11300 9900 14300 19400 8200 7800 8900 11700 11500 12400 14800 18300 21400 8100 10400 12200 8400 9200 12100 11700 13100 20200 16800 23100 19600 9500 12500 25000 8900 9800 9800 12900 13400 14400 19200 21100 19800 23900 30500 35500 12500 22600 10100 13300

2,070 2,450 3,500 2,600 3,700 5,500 2,750 2,230 2,650 3,800 2,800 3,150 3,950 5,100 5,300 2,380 3,300 4,000 2,550 2,850 4,050 3,000 3,450 6,100 4,350 6,500 4,250 3,050 4,300 7,800 2,850 3,200 3,200 4,600 3,650 4,000 5,800 6,500 5,000 6,400 8,800 9,300 3,950 7,000 3,400 4,850

9200 10900 15600 11500 16400 24300 12300 9900 11800 16800 12500 13900 17500 22800 23500 10600 14600 17900 11300 12700 18000 13300 15300 27000 19300 29000 18900 13500 19200 34500 12600 14300 14300 20400 16200 17900 26000 29000 22400 28500 39000 41500 17600 31000 15100 21500

24,000 24,000 24,000 24,000 24,000 24,000 24,000 24,000 24,000 24,000 23,000 23,000 23,000 23,000 22,000 23,000 23,000 23,000 22,000 22,000 22,000 22,000 22,000 22,000 22,000 22,000 21,000 22,000 22,000 21,000 21,000 21,000 21,000 21,000 21,000 21,000 21,000 21,000 20,000 20,000 20,000 20,000 21,000 21,000 21,000 21,000

18

Needle Roller And Cage AssembliesUNIT CAGE SERIESD Inch and metric D Single and double row

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section. For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.PART NUMBER SHAFT Fw inch SHAFT Fw mm HSG. BORE Ew inch HSG. BORE Ew mm WIDTH Bc inch WIDTH Bc mm WGT. WGT. DYN. CAP. C lbf DYN. CAP. C N STAT. CAP. C0 lbf STAT. CAP. C0 N SPEED LIMIT rpm

lbs

g

K 22x26x10 K 22x26x13 K 22x26x17 K 22x28x17 K 22x29x16 K 22x30x15 TN K 22x32x24 C141816 K 23x35x16 TN K 24x28x10 K 24x28x13 K 24x28x17 K 24x29x13 K 24x30x17 K 24x30x31 ZW K 25x29x10 K 25x29x13 K 25x29x17 K 25x30x13 K 25x30x17 K 25x30x20 K 25x30x26 ZW K 25x31x17 K 25x31x21 K 25x32x16 K 25x33x20 K 25x33x24 K 25x35x30 C161908 C162112 C162116 K 26x30x10 K 26x30x13 K 26x30x17 K 26x30x22 ZW K 28x33x13 K 28x33x17 K 28x33x27 TN K 28x34x17 K 28x35x16 K 28x35x18 K 28x35x27 K 28x40x18 K 28x40x25 C182212 C182416

0.866 0.866 0.866 0.866 0.866 0.866 0.866 0.875 0.906 0.945 0.945 0.945 0.945 0.945 0.945 0.984 0.984 0.984 0.984 0.984 0.984 0.984 0.984 0.984 0.984 0.984 0.984 0.984 1.000 1.000 1.000 1.024 1.024 1.024 1.024 1.102 1.102 1.102 1.102 1.102 1.102 1.102 1.102 1.102 1.125 1.125

22 22 22 22 22 22 22 22.225 23 24 24 24 24 24 24 25 25 25 25 25 25 25 25 25 25 25 25 25 25.400 25.400 25.400 26 26 26 26 28 28 28 28 28 28 28 28 28 28.575 28.575

1.024 1.024 1.024 1.102 1.142 1.181 1.260 1.125 1.378 1.102 1.102 1.102 1.142 1.181 1.181 1.142 1.142 1.142 1.181 1.181 1.181 1.181 1.221 1.221 1.260 1.299 1.299 1.378 1.188 1.313 1.313 1.181 1.181 1.181 1.181 1.299 1.299 1.299 1.339 1.378 1.378 1.378 1.575 1.575 1.375 1.500

26 26 26 28 29 30 32 28.575 35 28 28 28 29 30 30 29 29 29 30 30 30 30 31 31 32 33 33 35 30.162 33.338 33.338 30 30 30 30 33 33 33 34 35 35 35 40 40 34.925 38.100

0.394 0.512 0.669 0.669 0.630 0.591 0.945 1.000 0.630 0.394 0.512 0.669 0.512 0.669 1.221 0.394 0.512 0.669 0.512 0.669 0.787 1.024 0.669 0.827 0.630 0.787 0.945 1.181 0.500 0.750 1.000 0.394 0.512 0.669 0.866 0.512 0.669 1.063 0.669 0.630 0.709 1.063 0.709 0.984 0.750 1.000

10 13 17 17 16 15 24 25.400 16 10 13 17 13 17 31 10 13 17 13 17 20 26 17 21 16 20 24 30 12.700 19.050 25.400 10 13 17 22 13 17 27 17 16 18 27 18 25 19.050 25.400

0.017 0.021 0.026 0.04 0.035 0.04 0.095 0.066 0.064 0.019 0.022 0.029 0.031 0.042 0.071 0.019 0.024 0.031 0.024 0.035 0.04 0.042 0.042 0.044 0.046 0.073 0.086 0.143 0.027 0.072 0.096 0.015 0.024 0.033 0.026 0.029 0.037 0.042 0.053 0.053 0.06 0.09 0.11 0.154 0.062 0.131

7.5 9.5 12 18 16 18 43 30.1 29 8.5 10 13 14 19 32 8.5 11 14 11 16 18 19 19 20 21 33 39 65 12.4 32.6 43.5 7 11 15 12 13 17 19 24 24 27 41 50 70 28.2 59.3

2,050 2,340 3,100 4,350 4,500 4,500 7,600 6,500 5,500 2,160 2,470 3,250 3,050 4,400 6,200 2,230 2,550 3,350 3,300 4,200 4,900 4,800 4,400 5,600 4,700 6,400 7,600 10,600 3,050 6,400 8,200 2,270 2,600 3,400 3,550 3,450 4,450 5,200 4,900 4,850 5,400 7,900 7,500 10,200 5,000 9,700

9100 10400 13700 19400 20000 20100 34000 29000 24500 9600 11000 14500 13600 19500 27500 9900 11300 14900 14600 18700 21700 21400 19600 24700 21000 28500 34000 47000 13700 28500 36500 10100 11600 15200 15700 15300 19700 23300 21800 21500 24000 35000 33500 45500 22200 43000

3,000 3,600 5,100 6,100 5,700 5,300 9,000 9,800 5,400 3,350 3,950 5,600 4,450 6,200 9,800 3,450 4,150 5,800 4,900 6,700 8,200 8,000 6,400 8,500 6,300 8,500 10,600 13,900 4,700 8,500 11,900 3,600 4,300 6,200 6,400 5,400 7,500 9,200 7,500 6,600 7,600 12,400 8,300 12,400 7,400 13,400

13400 15900 22700 27000 25500 23400 40000 43500 23900 14800 17600 25000 19700 27500 43500 15400 18400 26000 21800 30000 36500 35500 28500 38000 28000 38000 47000 62000 20900 38000 53000 16100 19200 27500 28500 24200 33500 41000 33500 29500 34000 55000 37000 55000 33000 60000

20,000 20,000 20,000 20,000 19,000 19,000 18,000 19,000 17,000 19,000 19,000 19,000 18,000 18,000 18,000 18,000 18,000 18,000 18,000 18,000 18,000 18,000 18,000 18,000 17,000 17,000 17,000 16,000 18,000 17,000 17,000 18,000 18,000 18,000 18,000 16,000 16,000 16,000 16,000 16,000 16,000 16,000 14,000 14,000 15,000 15,000

19

Needle Roller And Cage AssembliesUNIT CAGE SERIESD Inch and metric D Single and double row

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section. For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.PART NUMBER SHAFT Fw inch SHAFT Fw mm HSG. BORE Ew inch HSG. BORE Ew mm WIDTH Bc inch WIDTH Bc mm WGT. WGT. DYN. CAP. C lbf DYN. CAP. C N STAT. CAP. C0 lbf STAT. CAP. C0 N SPEED LIMIT rpm

lbs

g

C182420 K 30x34x13 K 30x35x13 K 30x35x17 K 30x35x26 ZW K 30x35x27 K 30x37x16 K 30x37x18 K 30x40x18 K 30x40x30 C202412 (F88312) C202612 C202616 C202624 C202812 K 32x37x13 K 32x37x17 K 32x37x27 K 32x37x28 TN K 32x38x16 K 32x38x20 K 32x38x26 K 32x39x16 K 32x39x18 K 32x40x25 K 32x40x36 K 32x40x42 ZW TN K 32x46x32 C222820 K 35x40x13 K 35x40x17 K 35x40x25 K 35x40x27 TN K 35x40x30 ZW K 35x40x32 ZW K 35x42x16 K 35x42x18 K 35x42x20 K 35x42x30 K 35x43x18 K 35x45x20 K 35x45x30 K 35x45x49 K 36x42x16 K 37x42x17 K 37x42x27

1.125 1.181 1.181 1.181 1.181 1.181 1.181 1.181 1.181 1.181 1.250 1.250 1.250 1.250 1.250 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.260 1.375 1.378 1.378 1.378 1.378 1.378 1.378 1.378 1.378 1.378 1.378 1.378 1.378 1.378 1.378 1.417 1.457 1.457

28.575 30 30 30 30 30 30 30 30 30 31.750 31.750 31.750 31.750 31.750 32 32 32 32 32 32 32 32 32 32 32 32 32 34.925 35 35 35 35 35 35 35 35 35 35 35 35 35 35 36 37 37

1.500 1.339 1.378 1.378 1.378 1.378 1.457 1.457 1.575 1.575 1.500 1.625 1.625 1.625 1.750 1.457 1.457 1.457 1.457 1.496 1.496 1.496 1.535 1.535 1.575 1.575 1.575 1.811 1.750 1.575 1.575 1.575 1.575 1.575 1.575 1.654 1.654 1.654 1.654 1.693 1.772 1.772 1.772 1.654 1.654 1.654

38.100 34 35 35 35 35 37 37 40 40 38.100 41.275 41.275 41.275 44.450 37 37 37 37 38 38 38 39 39 40 40 40 46 44.450 40 40 40 40 40 40 42 42 42 42 43 45 45 45 42 42 42

1.250 0.512 0.512 0.669 1.024 1.063 0.630 0.709 0.709 1.181 0.750 0.750 1.000 1.500 0.750 0.512 0.669 1.063 1.102 0.630 0.787 1.024 0.630 0.709 0.984 1.417 1.654 1.260 1.250 0.512 0.669 0.984 1.063 1.181 1.260 0.630 0.709 0.787 1.181 0.709 0.787 1.181 1.929 0.630 0.669 1.063

31.750 13 13 17 26 27 16 18 18 30 19.050 19.050 25.400 38.100 19.050 13 17 27 28 16 20 26 16 18 25 36 42 32 31.750 13 17 25 27 30 32 16 18 20 30 18 20 30 49 16 17 27

0.163 0.031 0.031 0.042 0.079 0.066 0.06 0.066 0.106 0.161 0.068 0.107 0.143 0.215 0.149 0.04 0.042 0.066 0.046 0.055 0.066 0.084 0.082 0.068 0.108 0.161 0.17 0.262 0.195 0.042 0.046 0.068 0.086 0.106 0.11 0.075 0.075 0.082 0.148 0.084 0.123 0.176 0.304 0.064 0.049 0.09

74.1 14 14 19 36 30 27 30 48 73 31.1 48.7 64.9 97.4 67.8 18 19 30 21 25 30 38 37 31 49 73 77 119 88.2 19 21 31 39 48 50 34 34 37 67 38 56 80 138 29 22 41

11,700 2,750 3,500 4,400 5,400 6,900 5,200 5,800 7,200 11,000 5,800 7,800 10,100 14,400 10,200 3,500 4,450 6,700 5,300 4,850 6,000 7,500 5,400 6,000 8,400 12,100 11,200 14,800 12,600 3,650 4,700 6,600 5,600 5,700 7,200 5,500 6,200 6,700 8,800 6,400 8,300 11,900 18,400 5,500 5,000 7,200

52000 12300 15600 19600 24000 30500 23100 26000 32000 49000 26000 34500 45000 64000 45500 15500 19900 30000 23600 21500 26500 33500 23800 26500 37500 54000 50000 66000 56000 16200 20800 29500 25000 25500 32000 24400 27500 30000 39000 28500 37000 53000 82000 24600 22400 32000

17,100 4,900 5,700 7,600 9,900 13,300 7,500 8,700 9,000 15,500 9,600 10,500 14,600 22,700 12,400 5,700 8,000 13,500 9,800 7,800 10,100 13,700 8,000 9,200 13,000 20,700 18,900 18,700 19,800 6,300 8,700 13,500 10,900 11,200 14,800 8,400 9,700 11,000 15,300 9,400 11,200 17,800 31,500 9,600 9,700 15,300

76000 21700 25500 34000 44000 59000 33500 38500 40000 69000 42500 46500 65000 101000 55000 25500 35500 60000 43500 34500 45000 61000 35500 41000 58000 92000 84000 83000 88000 28000 38500 60000 48500 50000 66000 37500 43000 49000 68000 42000 50000 79000 139000 42500 43000 68000

15,000 15,000 15,000 15,000 15,000 15,000 15,000 15,000 14,000 15,000 15,000 13,000 13,000 13,000 13,000 14,000 14,000 14,000 14,000 14,000 14,000 14,000 14,000 14,000 14,000 14,000 14,000 13,000 12,000 13,000 13,000 13,000 13,000 13,000 13,000 13,000 13,000 13,000 13,000 13,000 12,000 12,000 12,000 13,000 12,000 12,000

20

Needle Roller And Cage AssembliesUNIT CAGE SERIESD Inch and metric D Single and double row

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section. For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.PART NUMBER SHAFT Fw inch SHAFT Fw mm HSG. BORE Ew inch HSG. BORE Ew mm WIDTH Bc inch WIDTH Bc mm WGT. WGT. DYN. CAP. C lbf DYN. CAP. C N STAT. CAP. C0 lbf STAT. CAP. C0 N SPEED LIMIT rpm

lbs

g

K 37x45x26 K 38x43x17 K 38x43x27 K 38x46x20 K 38x46x32 C243016 C243020 C243024 K 39x44x24 K 39x44x26 ZW K 40x44x13 K 40x45x13 K 40x45x17 K 40x45x21 K 40x45x27 K 40x45x30 ZW K 40x46x17 K 40x47x18 K 40x47x20 K 40x48x20 K 42x47x13 K 42x47x17 K 42x47x25 TN K 42x47x27 K 42x47x30 ZW K 42x50x18 K 42x50x20 K 43x48x17 K 43x48x27 K 43x50x18 C283412 C283416 C283424 K 45x49x19 K 45x50x17 K 45x50x27 K 45x50x32 TN K 45x51x36 ZW K 45x52x18 K 45x52x21 TN K 45x53x20 K 45x53x21 K 45x53x22 K 45x53x28 K 45x59x18 TN K 45x59x32

1.457 1.496 1.496 1.496 1.496 1.500 1.500 1.500 1.535 1.535 1.575 1.575 1.575 1.575 1.575 1.575 1.575 1.575 1.575 1.575 1.654 1.654 1.654 1.654 1.654 1.654 1.654 1.693 1.693 1.693 1.750 1.750 1.750 1.772 1.772 1.772 1.772 1.772 1.772 1.772 1.772 1.772 1.772 1.772 1.772 1.772

37 38 38 38 38 38.100 38.100 38.100 39 39 40 40 40 40 40 40 40 40 40 40 42 42 42 42 42 42 42 43 43 43 44.450 44.450 44.450 45 45 45 45 45 45 45 45 45 45 45 45 45

1.772 1.693 1.693 1.811 1.811 1.875 1.875 1.875 1.732 1.732 1.732 1.772 1.772 1.772 1.772 1.772 1.811 1.850 1.850 1.890 1.850 1.850 1.850 1.850 1.850 1.969 1.969 1.890 1.890 1.969 2.125 2.125 2.125 1.929 1.969 1.969 1.969 2.008 2.047 2.047 2.087 2.087 2.087 2.087 2.323 2.323

45 43 43 46 46 47.625 47.625 47.625 44 44 44 45 45 45 45 45 46 47 47 48 47 47 47 47 47 50 50 48 48 50 53.975 53.975 53.975 49 50 50 50 51 52 52 53 53 53 53 59 59

1.024 0.669 1.063 0.787 1.260 1.000 1.250 1.500 0.945 1.024 0.512 0.512 0.669 0.827 1.063 1.181 0.669 0.709 0.787 0.787 0.512 0.669 0.984 1.063 1.181 0.709 0.787 0.669 1.063 0.709 0.750 1.000 1.500 0.748 0.669 1.063 1.260 1.417 0.709 0.827 0.787 0.827 0.866 1.102 0.709 1.260

26 17 27 20 32 25.400 31.750 38.100 24 26 13 13 17 21 27 30 17 18 20 20 13 17 25 27 30 18 20 17 27 18 19.050 25.400 38.100 19 17 27 32 36 18 21 20 21 22 28 18 32

0.135 0.064 0.095 0.104 0.168 0.168 0.210 0.252 0.066 0.099 0.04 0.049 0.068 0.073 0.101 0.128 0.062 0.086 0.093 0.108 0.04 0.071 0.057 0.108 0.119 0.117 0.117 0.066 0.11 0.09 0.145 0.193 0.289 0.06 0.075 0.112 0.099 0.187 0.093 0.075 0.121 0.132 0.132 0.179 0.159 0.326

61 29 43 47 76 76.2 95.3 114.3 30 45 18 22 31 33 46 58 28 39 42 49 18 32 26 49 54 53 53 30 50 41 65.6 87.5 131.3 27 34 51 45 85 42 34 55 60 60 81 72 148

9,900 4,600 7,100 8,000 12,400 10,800 13,000 15,300 6,400 6,200 3,150 3,950 4,800 5,600 7,400 6,000 5,600 6,600 7,300 8,100 4,000 4,900 6,200 7,500 7,500 7,100 7,900 4,850 7,500 7,000 9,100 11,900 16,900 4,050 5,100 7,800 8,700 10,100 7,100 6,700 8,800 8,700 9,600 11,700 9,900 16,400

44000 20500 31500 35500 55000 48000 58000 68000 28500 27500 14000 17600 21400 24900 33000 26500 25000 29500 32500 36000 17800 21700 27500 33500 33500 31500 35000 21600 33500 31000 40500 53000 75000 18000 22500 34500 38500 45000 31500 30000 39000 38500 42500 52000 44000 73000

16,600 8,700 15,300 12,800 22,300 16,700 21,300 26,000 13,300 12,600 6,400 7,300 9,300 11,200 16,400 12,100 10,100 11,200 12,800 13,300 7,500 9,700 13,000 16,900 17,100 11,200 12,800 9,700 16,900 12,100 13,900 19,800 31,000 9,100 10,300 18,000 20,500 22,300 12,800 11,700 15,100 15,100 17,100 22,000 12,100 22,900

74000 38500 68000 57000 99000 74000 95000 116000 59000 56000 28500 32500 41500 50000 73000 54000 45000 50000 57000 59000 33500 43000 58000 75000 76000 50000 57000 43000 75000 54000 62000 88000 138000 40500 46000 80000 91000 99000 57000 52000 67000 67000 76000 98000 54000 102000

12,000 12,000 12,000 12,000 12,000 11,000 11,000 11,000 12,000 12,000 12,000 12,000 12,000 12,000 12,000 12,000 11,000 11,000 11,000 11,000 11,000 11,000 11,000 11,000 11,000 11,000 11,000 11,000 11,000 11,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 10,000 9,500 9,500

21

Needle Roller And Cage AssembliesUNIT CAGE SERIESD Inch and metric D Single and double row

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section. For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.PART NUMBER SHAFT Fw inch SHAFT Fw mm HSG. BORE Ew inch HSG. BORE Ew mm WIDTH Bc inch WIDTH Bc mm WGT. WGT. DYN. CAP. C lbf DYN. CAP. C N STAT. CAP. C0 lbf STAT. CAP. C0 N SPEED LIMIT rpm

lbs

g

K 45x59x36 K 47x52x17 K 47x52x27 K 47x53x25 K 47x55x28 K 48x54x19 K 50x55x13.5 K 50x55x17 K 50x55x20 K 50x55x30 K 50x57x18 K 50x58x20 K 50x58x25 K 52x57x12 K 55x60x20 K 55x60x27 K 55x60x30 K 55x60x40 ZW K 55x62x18 K 55x63x15 K 55x63x20 K 55x63x25 K 55x63x32 K 56x61x20 C364216 C364220 C364224 K 58x63x17 K 58x64x19 K 58x65x18 K 58x65x36 ZW K 60x65x20 K 60x65x30 K 60x66x33 ZW K 60x66x40 ZW K 60x68x20 K 60x68x23 K 60x68x25 K 60x68x27 K 60x68x30 ZW K 60x68x34 ZW K 60x75x42 K 62x70x40 ZW K 63x70x21 C404616 C404620

1.772 1.850 1.850 1.850 1.850 1.890 1.969 1.969 1.969 1.969 1.969 1.969 1.969 2.047 2.165 2.165 2.165 2.165 2.165 2.165 2.165 2.165 2.165 2.205 2.250 2.250 2.250 2.284 2.284 2.284 2.284 2.362 2.362 2.362 2.362 2.362 2.362 2.362 2.362 2.362 2.362 2.362 2.441 2.480 2.500 2.500

45 47 47 47 47 48 50 50 50 50 50 50 50 52 55 55 55 55 55 55 55 55 55 56 57.150 57.150 57.150 58 58 58 58 60 60 60 60 60 60 60 60 60 60 60 62 63 63.500 63.500

2.323 2.047 2.047 2.087 2.165 2.126 2.165 2.165 2.165 2.165 2.244 2.284 2.284 2.244 2.362 2.362 2.362 2.362 2.441 2.480 2.480 2.480 2.480 2.402 2.625 2.625 2.625 2.480 2.520 2.559 2.559 2.559 2.559 2.598 2.598 2.677 2.677 2.677 2.677 2.677 2.677 2.953 2.756 2.756 2.875 2.875

59 52 52 53 55 54 55 55 55 55 57 58 58 57 60 60 60 60 62 63 63 63 63 61 66.675 66.675 66.675 63 64 65 65 65 65 66 66 68 68 68 68 68 68 75 70 70 73.025 73.025

1.417 0.669 1.063 0.984 1.102 0.748 0.532 0.669 0.787 1.181 0.709 0.787 0.984 0.472 0.787 1.063 1.181 1.575 0.709 0.591 0.787 0.984 1.260 0.787 1.000 1.250 1.500 0.669 0.748 0.709 1.417 0.787 1.181 1.299 1.575 0.787 0.906 0.984 1.063 1.181 1.339 1.654 1.575 0.827 1.000 1.250

36 17 27 25 28 19 13.5 17 20 30 18 20 25 12 20 27 30 40 18 15 20 25 32 20 25.400 31.750 38.100 17 19 18 36 20 30 33 40 20 23 25 27 30 34 42 40 21 25.400 31.750

0.351 0.077 0.112 0.112 0.176 0.101 0.066 0.077 0.095 0.143 0.104 0.165 0.198 0.053 0.088 0.132 0.157 0.218 0.115 0.117 0.148 0.176 0.225 0.099 0.243 0.304 0.364 0.095 0.101 0.115 0.28 0.115 0.17 0.229 0.256 0.157 0.207 0.196 0.251 0.284 0.309 0.529 0.384 0.146 0.268 0.335

159 35 51 51 80 46 30 35 43 65 47 75 90 24 40 60 71 99 52 53 67 80 102 45 110.1 137.6 165.2 43 46 52 127 52 77 104 116 71 94 89 114 129 140 240 174 66 121.4 151.8

17,100 5,200 7,900 8,700 11,900 6,900 4,100 4,950 6,000 8,800 7,500 8,000 9,900 4,050 6,400 8,500 9,200 10,900 8,000 5,600 9,000 11,200 13,900 6,200 13,500 14,400 17,500 6,100 7,900 7,900 11,000 6,600 9,600 10,300 13,000 9,800 11,100 11,900 11,100 10,000 10,800 26,500 14,800 10,200 14,000 16,600

76000 23300 35000 38500 53000 30500 18200 22100 26500 39000 33500 35500 44000 18000 28500 38000 41000 48500 35500 25000 40000 50000 62000 27500 60000 64000 78000 27000 35000 35000 49000 29500 42500 46000 58000 43500 49500 53000 49500 44500 48000 118000 66000 45500 62000 74000

24,500 11,000 18,700 18,400 22,700 13,700 8,200 10,600 13,500 21,800 14,200 13,900 18,200 8,200 14,800 21,800 24,300 30,000 15,700 9,200 16,600 22,500 29,000 14,600 25,000 27,500 35,500 14,400 17,500 15,700 24,100 16,200 26,000 25,000 34,000 19,100 22,700 25,000 22,500 19,800 21,600 44,500 33,000 22,700 27,000 34,000

109000 49000 83000 82000 101000 61000 36500 47000 60000 97000 63000 62000 81000 36500 66000 97000 108000 133000 70000 41000 74000 100000 130000 65000 112000 122000 157000 64000 78000 70000 107000 72000 116000 112000 151000 85000 101000 111000 100000 88000 96000 197000 146000 101000 121000 151000

9,500 10,000 10,000 10,000 9,500 9,500 9,500 9,500 9,500 9,500 9,000 9,000 9,000 9,000 8,500 8,500 8,500 8,500 8,500 8,500 8,500 8,500 8,500 8,500 7,900 7,900 7,900 8,000 8,000 8,000 8,000 8,000 8,000 8,000 8,000 7,500 7,500 7,500 7,500 7,500 7,500 7,500 7,500 7,500 7,200 7,200

22

Needle Roller And Cage AssembliesUNIT CAGE SERIESD Inch and metric D Single and double row

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section. For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.PART NUMBER SHAFT Fw inch SHAFT Fw mm HSG. BORE Ew inch HSG. BORE Ew mm WIDTH Bc inch WIDTH Bc mm WGT. WGT. DYN. CAP. C lbf DYN. CAP. C N STAT. CAP. C0 lbf STAT. CAP. C0 N SPEED LIMIT rpm

lbs

g

C404624 K 64x70x16 K 65x70x20 K 65x70x30 K 65x73x23 K 65x73x30 K 68x74x20 K 68x74x30 K 68x74x35 ZW K 68x75x32 ZW K 70x76x20 K 70x76x30 K 70x78x25 K 70x78x30 K 70x78x46 ZW K 70x80x30 K 72x80x20 K 73x79x20 K 75x81x20 K 75x81x30 K 75x83x23 K 75x83x30 K 75x83x35 ZW K 75x83x40 ZW C485416 C485424 K 80x86x20 K 80x86x30 K 80x88x30 K 80x88x40 ZW K 80x88x46 ZW K 85x92x20 K 90x97x20 K 90x98x27 K 90x98x30 K 95x103x30 K 95x103x40 ZW K 100x107x21 K 100x108x27 K 100x108x30 C647224 K 105x112x21 K 105x113x30 K 110x117x24 K 110x118x30 K 115x123x27

2.500 2.520 2.559 2.559 2.559 2.559 2.677 2.677 2.677 2.677 2.756 2.756 2.756 2.756 2.756 2.756 2.835 2.874 2.953 2.953 2.953 2.953 2.953 2.953 3.000 3.000 3.150 3.150 3.150 3.150 3.150 3.347 3.543 3.543 3.543 3.740 3.740 3.937 3.937 3.937 4.000 4.134 4.134 4.331 4.331 4.528

63.500 64 65 65 65 65 68 68 68 68 70 70 70 70 70 70 72 73 75 75 75 75 75 75 76.200 76.200 80 80 80 80 80 85 90 90 90 95 95 100 100 100 101.600 105 105 110 110 115

2.875 2.756 2.756 2.756 2.874 2.874 2.913 2.913 2.913 2.953 2.992 2.992 3.071 3.071 3.071 3.150 3.150 3.110 3.189 3.189 3.268 3.268 3.268 3.268 3.375 3.375 3.386 3.386 3.465 3.465 3.465 3.622 3.819 3.858 3.858 4.055 4.055 4.213 4.252 4.252 4.500 4.409 4.449 4.606 4.646 4.843

73.025 70 70 70 73 73 74 74 74 75 76 76 78 78 78 80 80 79 81 81 83 83 83 83 85.725 85.726 86 86 88 88 88 92 97 98 98 103 103 107 108 108 114.300 112 113 117 118 123

1.500 0.630 0.787 1.181 0.906 1.181 0.787 1.181 1.378 1.260 0.787 1.181 0.984 1.181 1.811 1.181 0.787 0.787 0.787 1.181 0.906 1.181 1.378 1.575 1.000 1.500 0.787 1.181 1.181 1.575 1.811 0.787 0.787 1.063 1.181 1.181 1.575 0.827 1.063 1.181 1.500 0.827 1.181 0.945 1.181 1.063

38.100 16 20 30 23 30 20 30 35 32 20 30 25 30 46 30 20 20 20 30 23 30 35 40 25.400 38.100 20 30 30 40 46 20 20 27 30 30 40 21 27 30 38.100 21 30 24 30 27

0.402 0.117 0.123 0.183 0.238 0.311 0.157 0.221 0.265 0.291 0.157 0.243 0.273 0.326 0.496 0.331 0.216 0.165 0.174 0.251 0.273 0.324 0.401 0.465 0.318 0.476 0.132 0.174 0.304 0.501 0.573 0.225 0.24 0.331 0.379 0.364 0.587 0.265 0.408 0.397 0.847 0.284 0.476 0.379 0.478 0.441

182.1 53 56 83 108 141 71 100 120 132 71 110 124 148 225 150 98 75 79 114 124 147 182 211 144.0 216.0 60 79 138 227 260 102 109 150 172 165 266 120 185 180 384.0 129 216 172 217 200

19,600 6,300 6,900 9,900 10,300 12,800 8,000 10,500 10,900 12,100 8,100 11,700 11,700 13,500 17,500 16,400 9,300 8,300 8,400 11,700 11,200 13,900 14,200 16,400 14,800 21,100 8,700 12,600 16,200 17,100 19,800 10,000 10,100 13,700 15,300 15,500 18,700 10,800 12,800 16,000 27,500 10,700 16,200 12,600 17,500 14,200

87000 28000 30500 44000 46000 57000 35500 46500 48500 54000 36000 52000 52000 60000 78000 73000 41500 37000 37500 52000 50000 62000 63000 73000 66000 94000 38500 56000 72000 76000 88000 44500 45000 61000 68000 69000 83000 48000 57000 71000 122000 47500 72000 56000 78000 63000

42,000 13,500 17,300 28,000 21,100 27,500 18,900 26,500 28,000 29,000 19,300 31,500 25,000 30,500 42,500 33,500 19,100 20,200 21,100 32,000 24,500 32,000 33,000 40,000 31,500 49,000 22,000 35,500 40,000 43,000 52,000 24,300 25,500 33,500 38,500 40,500 51,000 28,500 32,000 42,500 62,000 28,500 44,500 35,500 49,000 38,000

186000 60000 77000 124000 94000 123000 84000 118000 125000 128000 86000 139000 112000 135000 189000 148000 85000 90000 94000 143000 109000 143000 147000 177000 140000 219000 98000 159000 179000 192000 231000 108000 113000 150000 172000 180000 228000 127000 143000 188000 275000 127000 197000 158000 219000 170000

7,200 7,500 7,500 7,500 7,000 7,000 7,000 7,000 7,000 7,000 6,500 6,500 6,500 6,500 6,500 6,500 6,500 6,500 6,500 6,500 6,000 6,000 6,000 6,000 6,100 6,100 6,000 6,000 6,000 6,000 6,000 5,500 5,000 5,000 5,000 4,900 4,900 4,700 4,700 4,700 4,500 4,500 4,500 4,300 4,300 4,100

23

Needle Roller And Cage AssembliesUNIT CAGE SERIESD Inch and metric D Single and double row

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section. For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.PART NUMBER SHAFT Fw inch SHAFT Fw mm HSG. BORE Ew inch HSG. BORE Ew mm WIDTH Bc inch WIDTH Bc mm WGT. WGT. DYN. CAP. C lbf DYN. CAP. C N STAT. CAP. C0 lbf STAT. CAP. C0 N SPEED LIMIT rpm

lbs

g

K 120x127x24 K 120x127x34 K 125x133x35 K 130x137x24 K 135x143x35 K 145x153x26 K 145x153x36 K 150x160x46 K 155x163x26 K 155x163x36 K 160x170x46 K 165x173x26 K 170x180x46 K 175x183x32 K 185x195x37 K 195x205x37 K 210x220x42 K 220x230x42 K 240x250x42 K 265x280x50

4.724 4.724 4.921 5.118 5.315 5.709 5.709 5.906 6.102 6.102 6.299 6.496 6.693 6.890 7.284 7.677 8.268 8.661 9.449 10.433

120 120 125 130 135 145 145 150 155 155 160 165 170 175 185 195 210 220 240 265

5.000 5.000 5.236 5.394 5.630 6.024 6.024 6.299 6.417 6.417 6.693 6.811 7.087 7.205 7.677 8.071 8.661 9.055 9.843 11.024

127 127 133 137 143 153 153 160 163 163 170 173 180 183 195 205 220 230 250 280

0.945 1.339 1.378 0.945 1.378 1.024 1.417 1.811 1.024 1.417 1.811 1.024 1.811 1.260 1.457 1.457 1.654 1.654 1.654 1.969

24 34 35 24 35 26 36 46 26 36 46 26 46 32 37 37 42 42 42 50

0.364 0.49 0.606 0.375 0.662 0.578 0.662 1.257 0.584 0.785 1.213 0.706 1.323 0.882 1.338 1.367 1.632 1.742 1.874 3.991

165 222 275 170 300 262 300 570 265 356 550 320 600 400 607 620 740 790 850 1810

13,300 18,200 19,300 13,700 20,500 16,600 22,000 33,000 16,900 22,500 34,000 18,200 35,500 22,300 29,000 30,000 34,500 35,500 37,000 57,000

59000 81000 86000 61000 91000 74000 98000 147000 75000 100000 152000 81000 158000 99000 128000 133000 154000 158000 164000 255000

39,000 58,000 58,000 42,000 65,000 51,000 73,000 106,000 53,000 76,000 115,000 60,000 121,000 79,000 96,000 101,000 126,000 133,000 142,000 193,000

174000 260000 260000 186000 290000 225000 325000 470000 236000 340000 510000 265000 540000 350000 425000 450000 560000 590000 630000 860000

4,000 4,000 3,800 3,700 3,500 3,300 3,300 3,200 3,100 3,100 3,000 2,900 2,800 2,700 2,600 2,500 2,300 2,200 2,000 1,800

24

Conrod BearingsKBK SERIESD Needle roller and cage assemblies D Wristpin bearing positions

For details on part numbers, descriptive suffixes and various technical references, please refer to front of this section. For engineering or technical information contact your local sales representative or call Distributor Sales (800)523-6572.PART NUMBER SHAFT Fw inch SHAFT Fw mm HSG. BORE Ew inch HSG. BORE Ew mm WIDTH Bc inch WIDTH Bc mm WEIGHT WEIGHT DYN. CAP. DYN. CAP. STAT. CAP. STAT. CAP. ROLLER LENGTH inch ROLLER LENGTH mm

lbs

g

lbf

N

lbf

N

KBK 9x13x12.5 KBK 10x13x14.5 KBK 10x14x13 KBK 12x15x13 KBK 12x15x15 KBK 12x15x17.5 KBK 12x16x13 KBK 12x16x16 KBK 13x17x17.5 KBK 14x18x13 KBK 14x18x14.5 KBK 14x18x17 KBK 14x18x21 KBK 15x19x20 KBK 16x20x20 KBK 18x22x22 KBK 18x22x24 KBK 18x22x25 KBK 20x24x30 KBK 20x25x22

0.354 0.394 0.394 0.472 0.472 0.472 0.472 0.472 0.512 0.551 0.551 0.551 0.551 0.591 0.630 0.709 0.709 0.709 0.787 0.787

9 10 10 12 12 12 12 12 13 14 14 14 14 15 16 18 18 18 20 20

0.512 0.512 0.551 0.591 0.591 0.591 0.630 0.630 0.669 0.709 0.709 0.709 0.709 0.748 0.787 0.866 0.866 0.866 0.945 0.984

13 13 14 15 15 15 16 16 17 18 18 18 18 19 20 22 22 22 24 25

0.492 0.571 0.512 0.512 0.591 0.689 0.512 0.630 0.689 0.512 0.571 0.669 0.827 0.787 0.787 0.866 0.945 0.984 1.181 0.866

12.5 14.5 13 13 15 17.5 13 16 17.5 13 14.5 17 21 20 20 22 24 25 30 22

0.011 0.01 0.013 0.01 0.012 0.014 0.015 0.019 0.022 0.018 0.018 0.024 0.024 0.029 0.031 0.037 0.04 0.044 0.051 0.044

5 4.7 6 4.7 5.5 6.5 7 8.5 10 8 8 11 11 13 14 17 18 20 23 20

1350 1210 1350 1330 1350 1750 1550 1800 2180 1640 1640 2160 2810 2540 2650 3040 3170 3130 3570 3640

6000 5400 6000 5900 6000 7800 6900 8000 9700 7300 7300 9600 12500 11300 11800 13500 14100 13900 15900 16200

1370 1480 1390 1730 1780 2470 1750 2140 2770 1960 1960 2790 3910 3480 3800 4650 4950 4830 5960 5240

6100 6600 6200 7700 7900 11000 7800 9500 12300 8700 8700 12400 17400 15500 16900 20700 22000 21500 26500 23300

0.386 0.425 0.386 0.386 0.425 0.543 0.386 0.465 0.543 0.386 0.386 0.504 0.701 0.622 0.622 0.622 0.701 0.78 0.78 0.642

9.8 10.8 9.8 9.8 10.8 13.8 9.8 11.8 13.8 9.8 9.8 12.8 17.8 15.8 15.8 15.8 17.8 19.8 19.8 16.3

25

Conrod BearingsKZK SERIESD Needle roller and cage assemblies D Crankpin bearing positions

For details on part numbers, descriptive suf