Cat TL943 Telehandler with Stabilizers Spec Sheet · PDF fileCat ® TL943C Telehandler with...
-
Upload
duongthien -
Category
Documents
-
view
221 -
download
1
Transcript of Cat TL943 Telehandler with Stabilizers Spec Sheet · PDF fileCat ® TL943C Telehandler with...
Cat®
TL943CTelehandler with Stabilizers
SpecificationsEngineModel Cat® C3.4B Tier 4 InterimGross Power (Basic) 83 kW 111.3 hpMaximum Torque (Standard) 450 Nm at 1400 rpm 332 lb-ftBore 99 mm 3.9 inStroke 110 mm 4.3 inDisplacement 3.4 L 207 .5 cu in
WeightsOperating Weight 12 304 kg 27,125 lb
Operating SpecificationsRated Load Capacity 4082 kg 9,000 lbMaximum Lift Height 13.1 m 43 ftMaximum Forward Reach 9.6 m 31.4 ftFrame Leveling 10°Top Travel Speed 32.7 kph 20.3 mph Capacity at Max Height (o/r Up) 3175 kg 7,000 lbCapacity at Max Height (o/r Down) 3175 kg 7,000 lbCapacity at Max Reach (o/r Up) 499 kg 1,100 lbCapacity at Max Reach (o/r Down) 1225 kg 2,700 lbTurning Radius over Tires 3.7 m 12 ftDrawbar Pull (Loaded) 115.7 kN 26,000 lb
Hydraulic SystemVariable displacement load sensing axial piston pump• Auxiliary Hydraulic Circuit used for all attachments equipped
with cylinders or other hydraulic components. Consists of valves, controls and hydraulic lines.
Service Refill CapacitiesFuel Tank 144 L 38 galHydraulic System 178 L 47 gal
TiresStandard 370/75-28 Duraforce MT Optional 13.00 x 24 Foam Filled 370/75-28 Foam Filled 13.00 x 24 12 PR
Transmission SpeedsForward 4 speedReverse 3 speed
Boom PerformanceBoom Up 13.9 SecondsBoom Down 10.2 SecondsTele In 16.8 SecondsTele Out 14.9 Seconds
Axles • Trunnion mounted planetary 55 degree steer axles. • Integral steer cylinder. • High bias limited slip differential on front axle.
Brakes• Service Brakes are inboard wet disc brakes on front and rear axles.• Parking Brakes are spring-applied hydraulic release on front axle.
Light on dash indicates when brake is on.
Work ToolsHydraulic Includes Includes IT Coupler Auxiliary Electrics Auxiliary ElectricsPallet Forks (2) 1525 mm, (2) 60 in, 2.36 in x 6 in 60 mm x 150 mm (2) 1220 mm, (2) 48 in, 2.36 in x 4 in 60 mm x 100 mm (2) 1220 mm, (2) 48 in, 2.36 in x 5 in 60 mm x 125 mm Lumber Forks (2) 1525 mm, (2) 60 in, 1.75 in x 7 in 45 mm x 180 mm (2) 1829 mm, (2) 72 in, 2 in x 6 in 50 mm x 150 mmCubing Forks (2) 1220 mm, (2) 48 in, 2 in x 2 in 50 mm x 50 mmCarriages:Standard Tilt 1270 mm 50 inWide Tilt 1829 mm 72 inSide Shift 1220 mm 48 inStandard Rotate 1270 mm 50 inWide Rotate 1829 mm 72 inSwing 100°, 1829 mm, 4028 kg 100°, 72 in, 9,000 lb Capacity, 2268 kg Swung Capacity, 5,000 lb SwungDual Fork Positioning 1270 mm 50 in
cat000046-13TL943Cs-SS-D5e.indd 1 4/19/12 9:46 AM
For more complete information on Cat products, dealer services, and industry solutions, visit us on the web at www.cat.com
© 2012 Caterpillar All rights reserved. Printed in U.S.A.
Materials and specifications are subject to change without notice. Featured machines in photos may include additional equipment. See your Cat dealer for available options.
CAT, CATERPILLAR, SAFETY.CAT.COM, their respective logos, “Caterpillar Yellow” and the POWER EDGE trade dress, corporate and product identity used herein, are trademarks of Caterpillar and may not be used without permission.
STABILIZERS DOWN STABILIZERS UP
A
C
E
B
D
F
20°
8.5 m (28 ft)
9.7 m (32 ft)
10.9 m (36 ft)
12.1 m (40 ft)
13.4 m (44 ft)
14.6 m (48 ft)
7.3 m (24 ft)
6.1 m (20 ft)
4.9 m (16 ft)
3.7 m (12 ft)
2.4 m (8 ft)
-2.4 m (-8 ft)
1.2 m (4 ft)
0 m (0 ft)
-1.2 m (-4 ft)
3.7 m (12 ft)
4.9 m(16 ft)
6.1 m(20 ft)
7.3 m(24 ft)
8.5 m(28 ft)
9.7 m(32 ft)
10.9 m(36 ft)
2.4 m (8 ft)
1.2 m (4 ft)
0 m (0 ft)
40°
50°
60°
69°
0°
10°
30°
-6°
1225
kg
(2,7
00 lb
)
1814
kg
(4,0
00 lb
)
2268
kg
(5,0
00 lb
)
3175
kg
(7,0
00 lb
)
4082
kg
(9,0
00 lb
)
A
C
E
B
D
F
20°
8.5 m (28 ft)
9.7 m (32 ft)
10.9 m (36 ft)
12.1 m (40 ft)
13.4 m (44 ft)
14.6 m (48 ft)
7.3 m (24 ft)
6.1 m (20 ft)
4.9 m (16 ft)
3.7 m (12 ft)
2.4 m (8 ft)
-2.4 m (-8 ft)
1.2 m (4 ft)
0 m (0 ft)
-1.2 m (-4 ft)
3.7 m (12 ft)
16 ft(4.9 m)
4.9 m(16 ft)
7.3 m(24 ft)
8.5 m(28 ft)
9.7 m(32 ft)
10.9 m(36 ft)
2.4 m (8 ft)
1.2 m (4 ft)
0 m (0 ft)
40°
50°
60°
69°
0°
10°
30°
-6°
1225
kg
(2,7
00 lb
)
1814
kg
(4,0
00 lb
)
2268
kg
(5,0
00 lb
)
3175
kg
(7,0
00 lb
)
4082
kg
(9,0
00 lb
)
-10 10 20 30 40 50 60 70 80
TL943
-10 10 20 30
40 50 60
70 80
TL943
-1010 20
30 4050 60 70 80
TL943
-10 1020 30
40 5060
7080 TL943
A
C
E
B
D
F
20°
8.5 m (28 ft)
9.7 m (32 ft)
10.9 m (36 ft)
12.1 m (40 ft)
13.4 m (44 ft)
14.6 m (48 ft)
7.3 m (24 ft)
6.1 m (20 ft)
4.9 m (16 ft)
3.7 m (12 ft)
2.4 m (8 ft)
-2.4 m (-8 ft)
1.2 m (4 ft)
0 m (0 ft)
-1.2 m (-4 ft)
3.7 m(12 ft)
4.9 m(16 ft)
6.1 m(20 ft)
7.3 m(24 ft)
8.5 m(28 ft)
9.7 m(32 ft)
10.9 m(36 ft)
2.4 m (8 ft)
1.2 m (4 ft)
0 m (0 ft)
3.7 m(12 ft)
4.9 m(16 ft)
6.1 m(20 ft)
7.3 m(24 ft)
8.5 m(28 ft)
9.7 m(32 ft)
10.9 m(36 ft)
2.4 m(8 ft)
1.2 m(4 ft)
0 m(0 ft)
40°
50°
60°
69°
0°
10°
30°
-6°
499
kg (1
,100
lb)
907
kg (2
,000
lb)
1361
kg
(3,0
00 lb
) 18
14 k
g (4
,000
lb)
2268
kg
(5,0
00 lb
)
3175
kg
(7,0
00 lb
)
4082
kg
(9,0
00 lb
)
A
C
E
B
D
F
20°
8.5 m (28 ft)
9.7 m (32 ft)
10.9 m (36 ft)
12.1 m (40 ft)
13.4 m (44 ft)
14.6 m (48 ft)
7.3 m (24 ft)
6.1 m (20 ft)
4.9 m (16 ft)
3.7 m (12 ft)
2.4 m (8 ft)
-2.4 m (-8 ft)
1.2 m (4 ft)
0 m (0 ft)
-1.2 m (-4 ft)
40°
50°
60°
69°
0°
10°
30°
-6°
499
kg (1
,100
lb)
907
kg (2
,000
lb)
1361
kg
(3,0
00 lb
) 18
14 k
g (4
,000
lb)
2268
kg
(5,0
00 lb
)
3175
kg
(7,0
00 lb
)
4082
kg
(9,0
00 lb
)
-10 10 20 30 40 50 60 70 80
TL943
-10 10 20 30
40 50 60
70 80
TL943
-1010 20
30 4050 60 70 80
TL943
-10 1020 30
40 5060
7080 TL943
TL943C Telehandler with Stabilizers
Dimensions
All dimensions are approximate.
AEHQ6744-00 (03-2012)
Load Chart and Dimensions
Rated lift capacities shown are with machine equipped with carriage and pallet forks. The machine must be level on a firm surface with undamaged, properly inflated tires. Machine specifications and stability are based on rated lift capacities at specific boom angles and boom lengths.
(If specifications are critical, the proposed application should be discussed with your dealer.)
DO NOT exceed rated lift capacity loads, as unstable and dangerous machine conditions will result.
DO NOT tip the machine forward to determine the allowable load.
Use only approved attachments with proper material handler model/attachment load capacity charts displayed in the operator’s cab. OSHA
requires all rough terrain forklift operators be trained according to OSHA 29 CFR 1910.178 (1).
Due to continuous product improvements, machine specifications and/or equipment changes may be made without prior notification. This machine meets or exceeds ANSI/ITSDF B56.6-2005 as originally manufactured for intended applications.
IMPORTANT
2.42 m (95.3 in) 3.35 m (132 in)
6.25 m (246 in)
483 mm (19 in)
2.43
m (9
5.5 i
n)
3.43 m (135 in)
cat000046-13TL943Cs-SS-D5e.indd 2 4/19/12 9:46 AM