CAODC LEVEL III INSPECTION CHECKLIST C I B R · caodc level iii inspection checklist edition #3...

CAODC LEVEL III INSPECTION CHECKLIST

Edition #3 09/2016 1 of 3

COMPANY: DATE OF INSPECTION: INSPECTED BY:

RIG #: MODEL: MANUFACTURER:

MASTS SHEAVES OK REPAIR N/A 1. Groove wear in sheaves

2. Check sheaves for cracks

3. Warped

4. Water table condition

5. Side play in sheave

6. Crown pillars

7. Crown hand railings

8. Fall protection anchor point(s)

9. Guy line anchors

10. Winch line/rod transfer sheaves

11. Tong line anchor

COMMENTS:

TOP SECTION OK REPAIR N/A 1. Anchor point for rod transfer

2. Anchor point for tong sheave

3. Anchor point for rod basket

4. Main supports

5. Cross members

6. Locking pins

7. Condition of ladder

COMMENTS:

ROD BASKET OK REPAIR N/A

1. Frame

2. Fingers

3. Pin condition

4. Safety chains or cables

COMMENTS:

MONKEYBOARD OK REPAIR N/A 1. Frame condition

2. Fingers condition

3. Pin condition

4. Safety chains

5. Handrails

6. Sheave anchors

COMMENTS:

LOWER SECTION OK REPAIR N/A 1. Locking pin saddle

2. Anchor point for monkey board

3. Chain for hanging blocks

4. Stand pipe brackets

5. Kelly hose safety chained

6. Main supports

7. Cross members8. Raising ram anchor points (remove pins to

inspect) 9. Raising ram pins (remove pins to inspect)

10. Anchor points for scoping ram

11. Floor brackets

12. Tong anchor

13. Winch anchor point

14. Block plate

15. Condition of ladder

16. Manufacturers rating plate

COMMENTS:

TURNBUCKLES OK REPAIR N/A 1. Adjuster condition

2. End connection pin hole

3. End connection threads

COMMENTS:

HYDRAULICS OK REPAIR N/A 1. Hydraulic system

2. Raising ram condition

3. Hose and hose ends

4. Connections

5. Pins and bolts

6. Ram flow restrictor

COMMENTS:

TRUNION OK REPAIR N/A 1. Arms

2. Locks

3. Slides

4. A-base

COMMENTS:

BOOM OK REPAIR N/A 1. Condition

2. Sheaves

3. Anchor points

4. Stoppers

COMMENTS:

SUBSTRUCTURES OK REPAIR N/A 1. Attachment lugs

2. Mast shoes (radius base beam)

3. Table spreader beams

4. Setback beams

5. Spreader legs

6. Pins

7. BOP carrier

8. Condition of welds

9. Condition of decking

COMMENTS:

OVERHEAD EQUIPMENT BLOCKS OK REPAIR N/A 1. Top bolt covers

2. Main sheave bolt

3. Retaining pins

4. Sheave grooves

Make: Model:

Serial #: Equip.#:

Inspection Date: Insp. Comp.:

Insp.#: Tonnage:

COMMENTS:

HOOK AND/OR BECKET OK REPAIR N/A 1. Check hook/becket bolts

2. Check eyewear on hook/becket

3. Check eyewear for rod clevis

4. Does spring seem tight

5. Swivel hook to check bearing

6. Hook latching mechanism

7. If weights added, check welds

8. Shank gap

Make: Model:

Serial #: Equip.#:


Insp.#: Tonnage:

COMMENTS:

LIFTING NUBBINS – 60.3 MM OK REPAIR N/A 1. Threads

2. Body

3. Welds

Make: Model:

Serial #: Equip.#:


Insp.#: Tonnage:

COMMENTS:

LIFTING NUBBINS – 73.0 MM OK REPAIR N/A 1. Threads

2. Body

3. Welds

Make: Model:

Serial #: Equip.#:


Insp.#: Tonnage:

COMMENTS:

SERIAL #:

OK REPAIR N/A 1. Threads

2. Body

3. Welds

Make: Model:

Serial #: Equip.#:


Insp.#: Tonnage:

COMMENTS:

TUBING ELEVATORS – 60.3 MM OK REPAIR N/A 1. Check latch pin

2. Check spring

3. Check latch

4. Check elevator body

5. Check hinge pin

6. Check keeper pin

Make: Model:

Serial #: Equip.#:


Insp.#: Tonnage:

COMMENTS:


2. Check spring

3. Check latch


5. Check hinge pin

6. Check keeper pin

Make: Model:

Serial #: Equip.#:


Insp.#: Tonnage:

COMMENTS:


2. Check spring

3. Check latch


5. Check hinge pin

6. Check keeper pin

Make: Model:

Serial #: Equip.#:


Insp.#: Tonnage:

COMMENTS:


2. Check spring

3. Check latch


5. Check hinge pin

6. Check keeper pin

Make: Model:

Serial #: Equip.#:


Insp.#: Tonnage:

COMMENTS:


2. Check spring

3. Check latch


5. Check hinge pin

6. Check keeper pin

Make: Model:

Serial #: Equip.#:


Insp.#: Tonnage:

COMMENTS:

LIFTING NUBBINS – 88.9 MM


Edition #3 09/2016 2 of 3

ROD ELEVATORS: 1 OK REPAIR N/A 1. Insert size:

2. Check springs

3. Check rod release springs

4. Check elevator bail

5. Snap rings in place

6. Insert condition

7. All screws in insert


9. Check safety latch

10. Are latch inserts worn

Make: Model:

Serial #: Equip.#:


Insp.#: Tonnage:

COMMENTS:


2. Check springs




6. Insert condition





Make: Model:

Serial #: Equip.#:


Insp.#: Tonnage:

COMMENTS:


2. Check springs




6. Insert condition





Make: Model:

Serial #: Equip.#:


Insp.#: Tonnage:

COMMENTS:

ROD ELEVATORS: 4 OK REPAIR N/A Insert size:

2. Check springs




6. Insert condition





Make: Model:

Serial #: Equip.#:


Insp.#: Tonnage:

COMMENTS:

ROD ELEVATORS: 5 OK REPAIR N/A Insert size:

2. Check springs




6. Insert condition





ROD ELEVATORS: 5 - CONTINUED

Model:

Serial #: Equip.#:


Insp.#: Tonnage:

COMMENTS:


2. Check springs




6. Insert condition





Make: Model:

Serial #: Equip.#:


Insp.#: Tonnage:

COMMENTS:


2. Check springs




6. Insert condition





Make: Model:

Serial #: Equip.#:


Insp.#: Tonnage:

COMMENTS:


2. Check springs




6. Insert condition





Make: Model:

Serial #: Equip.#:


Insp.#: Tonnage:

COMMENTS:

ROD TRANSFER: 1 OK REPAIR N/A 1. Transfer size:

2. Check D-ring

3. Check i-bolt

4. Check transfer body

5. Check bearing

Make: Model:

Serial #: if applicable Equip.#:

Inspection Date: Insp. Comp.: if applicable

Tonnage: Insp.#: if applicable

COMMENTS:


2. Check D-ring

3. Check i-bolt


5. Check bearing

Make:


Inspection Date:

ROD TRANSFER: 2 - CONTINUED


COMMENTS:


2. Check D-ring

3. Check i-bolt


5. Check bearing

Make: Model:




COMMENTS:


2. Check D-ring

3. Check i-bolt


5. Check bearing

Make: Model:




COMMENTS:


2. Check D-ring

3. Check i-bolt


5. Check bearing

Make: Model:




COMMENTS:


2. Check D-ring

3. Check i-bolt


5. Check bearing

Make: Model:




COMMENTS:

BAILS OK REPAIR N/A 1. Check for cracks

2. Check for scarring

3. Check ears for gouging

Make: Model:

Serial #: Equip.#:


Insp.#: Tonnage:

COMMENTS:

ROD LOAD CLEVIS OK REPAIR N/A 1. Check for wear

2. Check pins & bolts for wear

3. Safety/cotter pins in place

Make: Model:

Serial #: Equip.#:


Insp.#: Tonnage:

COMMENTS:

ROD HOOK OK REPAIR N/A 1. Rotate hook to check swivel

2. Rod hook safety latch

3. Hook wear

4. Safety guard over latch release

5. Bail wearInsp. Comp.: if applicable

Make:

1.

Model:


Edition #3 09/2016 3 of 3

ROD HOOK - CONTINUED

Make: Model:

Serial #:

Inspection Date:

Equip.#:

Insp. Comp.: if applicable

Insp.#: Tonnage:

COMMENTS:

KELLY SWIVEL OK REPAIR N/A 1. Bail

2. Pins on bail

3. Gooseneck

4. Upper kelly cock

5. Thread condition on kelly cock

Make: Model:

Serial #:

Inspection Date:

Equip.#:


Insp.#: Tonnage:

COMMENTS:

POWER SWIVEL OK REPAIR N/A 1. Track condition

2. Pins for track

3. Safety connections inside track

4. Crown hanger

5. Links on top drive

6. Pins for balls

7. Upper kelly cock

8. Thread condition on kelly cock

9. Safety chains for hoses

10. Gooseneck

Make: Model:

Serial #:

Inspection Date:

Equip.#:


Insp.#: Tonnage:

COMMENTS:

DRAWWORKS BRAKE LOAD PATH COMPONENTS MAIN DRUM: EXTERNAL COMPONENT OK REPAIR N/A 1. Brake bands

2. Brake handle

3. Brake handle locking mechanism

4. Brake linkage components:

− Welded external lugs

− Linkage arm

− Drawworks input lug

− Bearing blocks− Washers/cotter pins or pin

connections

MAIN DRUM: EXTERNAL COMP. - CONTINUED OK REPAIR N/A − Pins

− Pinholes in lugs

− Threaded connections

5. Auxiliary brake or equivalent

6. Any other load bearing mechanical brake

COMMENTS:

MAIN DRUM: INTERNAL COMPONENT OK REPAIR N/A 1. Brake bands

2. Brake links - welded

3. Brake links – solid

4. Brake turnbuckles

5. Brake equalizer

6. Threaded connections

7. Pins

8. Pinholes in lugs

9. Brake block wear

10. Flange condition


COMMENTS:

SANDLINE DRUM: EXTERNAL COMPONENT OK REPAIR N/A 1. Brake bands

2. Welded external lugs

3. Linkage arm

4. Drawworks input lug

5. Bearing blocks

6. Washers/cotter pins or pin connections

7. Pins

8. Pinholes in lugs


COMMENTS:

SANDLINE DRUM: INTERNAL COMPONENT OK REPAIR N/A 1. Brake bands

2. Brake links - welded

3. Brake links – solid

4. Brake turnbuckles

5. Brake equalizer


7. Pins

8. Pinholes in lugs

9. Brake block wear

10. Flange condition

CARRIER MOUNTED EQUIPMENT FREE STANDING PACKAGES OK REPAIR N/A 1. Off Drillers side main beam

2. Load line lugs

3. Turnbuckle lug weld

4. Drillers side main beam

5. Cross member connection

6. Turnbuckle pin connection

COMMENTS:

A-LEGS OK REPAIR N/A 1. Pin condition

2. Frame

3. Threaded legs

COMMENTS:

HEADACHE RACK OK REPAIR N/A 1. Tie down

2. Rack structure

COMMENTS:

OUTRIGGERS OK REPAIR N/A 1. Pins and lugs (outrigger to carrier)

2. Frame condition

3. Frame welds

4. Guy line lugs

5. Spreader bar condition

6. Screw jack condition

7. All keeper pins and chains

8. Belly jack condition

9. Belly jack attachment points

10. Mat condition

COMMENTS:

CYLINDER MOUNTS OK REPAIR N/A 1. Raising ram condition

2. Raising ram connection

COMMENTS:

DEADLINE ANCHORS (IF APPLICABLE) OK REPAIR N/A 1. Drill line anchor bolts

2. Drill line anchor welds

COMMENTS:

LEVEL III INSPECTION COMPLETION

This Level III Inspection been logged in the Overhead Equipment Log Book

This Level III Inspection was done in accordance with CAODC RP’s: 3.0, 4.0, 10.0 and 11.0

Inspector’s Signature:

Field Superintendent’s Signature:

Estimated Completion Date For All Repairs:

COMMENTS:

CAODC LEVEL III INSPECTION CHECKLIST C I B R · caodc level iii inspection checklist edition #3...

Documents

Transcript of CAODC LEVEL III INSPECTION CHECKLIST C I B R · caodc level iii inspection checklist edition #3...