Canon Errors 2
description
Transcript of Canon Errors 2
Error Code Description
C0030 Fax PWB Problem. Processing with fax software is
disabled due to software or hardware issues.
C0060 Main PWB Type Mismatch Error.
C0070 Fax PWB Incompatability Detection Problem. Fax
software is not compatible with main PWB software.
C0130 Main PWB EEPROM Backup Memory Device Problem.
EEPROM can not be written or read.
C0140 Main PWB EEPROM Backup Memory Data Problem.
Abnormal reading data from EEPROM.
C0150 Engine PWB EEPROM Backup Memory Device
Problem. EEPROM cannot be written or read.
C0160 Engine PWB EEPROM Backup Memory Data Problem.
Abnormal reading data from EEPROM. Read & write
data do not match five times consecutively.
C0170 Copy Counts Problem. A checksum error is detected
in the main and engine backup memories for copy
counters.
C0180 Machine Number Mismatch Error. Machine number
does not match on main and engine PWBs
C0600 Main PWB DIMM Installed Incorrectly.
C0610 Main PWB DIMM error
C0630 DMA transmission of compressed, decompressed,
rotated, relocated, or blanked-out image data does
not complete within a specified period of time.
C0640 Hard Disk Drive cannot be accessed
C0700 Optional CF backup is not suitable.
C0800 Image processing problem. JAM05 is detected twice.
C0830 Fax Flash ROM program area checksum error
C0870 Fax PWB to Main PWB high capacity data transfer
problem.
C0880 Fax PWB program archive problem.
C0920 Fax backup data is not retained.
C1010 Cassette #1 Lift Motor error. Exceeds 12 seconds of
operation or 500ms of overcurrent.
C1020 Cassette #2 Lift Motor error. Exceeds 12 seconds of
operation or 500ms of overcurrent.
C1030 PF-700 optional cassette #3 lift motor error.
C1040 PF-700 optional cassette #4 lift motor error.
C1100 PF-750 (Left) Lift Motor 1 error. Exceeds 1 second
overcurrent.
C1110 PF-750 (Right) Lift Motor 2 error. Exceeds 1 second
overcurrent.
C1120 PF-750 (Left) Lift Motor 1 position problem. PF
switch 2 remains off after 30 seconds of motor
operation.
C1130 PF-750 (Right) Lift Motor 2 position problem. PF
switch 1 remains off after 30 seconds of motor
operation.
C1800 PF-700/PF-750 Communication Problem.
C1900 PF-700 EEPROM error. Write data & Read data are
not in agreement three times consecutively.
C2000 Drive Motor Problem. Stable Off is detected
exceeding 1 sec after motor stability. Stabilization is
not detected with 6 sec of activation.
C2250 Main Charge Cleaner Motor error. Lock error is
detected three times in a row during cleaner motor
operation.
C2500 Paper Feed Motor error. Stable Off is detected
exceeding 1 sec after motor stability. Stabilization is
not detected within 6 seconds of activation.
C2600 PF-700 Drive Motor error. Lock signal exceeds
500ms.
C2600 PF-750 Paper Conveying Motor error. Lock signal
exceeds 450ms.
C3100 Scanner Carriage Problem. Scanner home position
is not detected at initialization or start of copying
from contact glass.
C3200 Exposure Lamp Problem. Exposure lamp does not
reach the input value threshold within 5 sec of
commencing reading.
C3210 Exposure Lamp Problem. Exposure lamp does not
exceed the input threshold value within 5 sec of
commencing reading.
C3300 CCD AGC Problem. After AGC correct input is not
obtained at the CCD.
C3310 CIS AGC Problem. After AGC correct input is not
obtained at the CIS.
C3500 Communication Error Between Scanner and SHD.
C3900 Scanner PWB Backup Memory Read/Write Problem.
Read & Write data does not match.
C3910 Scanner PWB Backup Memory Data Problem. Data
in a specified area of the backup memory does not
match the specified values.
C4000 Polygon Motor Synchronization Problem. Polygon
motor does not stabilize speed within 20 sec of
activation.
C4010 Polygon Motor Steady-State Problem. Stable Off is
detected for 20 sec continuously after polygon
motor stabilization.
C4200 BD Steady-State Problem. ASIC detects a Beam
Detect error A for 2 sec after polygon motor
stabilization.
C5300 Cleaning Lamp Broken Wire. While the cleaning
lamp is On, the broken wire detection signal is
detected for 2 sec continuously.
C6000 Fuser Heater Break. Thermistor1 detected less than
70C/158F for 10 sec during warmup & ready.
Thermistor2 detected less than 40C/104F for 10 sec
during warmup & ready. Temp at thermistor 1or 2
does not rise by at least 1C/1.8F within 5 sec.
C6020 Abnormally High Thermistor Temperature.
Thermistor 1 or 2 is detected 250C/482F for 40ms
or more.
C6030 Fixing Thermistor Break Error. Thermistor break
signal is detected for 1 sec.
C6050 Abnormally Low Thermistor Temperature.
Thermistor 1 is detected 80C/176F or less for 1 sec
continuously during copying.
C6400 Zero-Cross Signal Error. While fuser heater On/Off
control is performed, the zero-cross signal is not
input within 3 sec.
C6410 Fuser Unit Connection Insertion Problem. Absence
of fuser unit is detected.
C6420 Fuser Unit Fuse Cut Problem. The fuse has been cut
33 sec after the fuse cut signal is turned on.
C7300 Toner Container Problem. Toner level is not
detected when toner empty is detected.
C7400 Developing Unit Connection Insertion Problem.
Absence of the developing unit is detected.
C7410 Drum Unit Connection Insertion Problem. Absence
of the drum unit is detected.
C7800 Broken External Thermistor Wire. Thermistor on the
environmental sensor outputs 4.5v or more.
C7810 Short-Circuited External Thermistor. Thermistor
input value is 0.5v or less.
C7900 Drum EEPROM Error. Reading or writing to the
EEPROM cannot be performed.
C7910 Developing EEPROM Error. Reading or writing to the
EEPROM cannot be performed.
C8020 DF-710 Punch Motor Problem. Punch motor lock
signal is detected for 500ms or more during
activation.
C8030 DF-730 Tray Upper Limit Detection Problem. When
tray elevation motor raises a tray, the upper limit
switch detects On condition.
C8050 DF-710 Paper Conveying Belt Motor 1 Error. Paper
conveying belt home position sensor 1 does not
turn Off within 1.5 sec. Paper conveying belt home
position sensor 1 does not turn On within 2.5 sec.
Jam 88.
C8060 DF-710 Paper Conveying Belt Motor 2 Error. Paper
conveying belt home position sensor 2 does not
turn Off within 1.5 sec. Paper conveying belt home
position sensor 2 does not turn On within 2.5 sec.
C8070 DF-710 Internal Tray Communication Error. The
connection is detected, but communication is not
possible with the internal tray.
C8140 DF-710 Main Tray Problem. Main tray is not
detected in not detected by main tray top limit
detection sensor or main tray capacity detection
sensor within 20 sec of ascending. Main tray upper
limit detection sensor or main tray load detection
sensor is not detected as Off within 20 sec of main
tray descending. Main tray lower limit detection
sensor is not detected as On within 20 sec of main
tray descending. Main tray upper limit detection
sensor or main tray load detection sensor remain on
for 2 sec or more during main tray ascent.
C8140 DF-730 Tray Elevation Motor Problem. Tray lower
limit sensor or surface view sensor cannot be
detected within 10 sec.
C8170 DF-710 Side Registration Motor 1 Problem. During
initial rotations home position is not detected within
3 sec. Jam 88.
C8170 DF-720 Front Side Registration Motor Problem.
During initial rotations home position is not
detected within 106 pulses. When the front side
home position sensor is turned off during
initialization, the sensor did not turn on within 3
sec.
C8170 DF-730 Adjustment Motor Problem. Adjustment
motor home position motor is not detected within a
specific time during activation.
C8180 DF-710 Side Registration Motor 2 Problem. During
initial rotations home position is not detected within
3 sec. Jam 88.
C8180 DF-720 Rear Side Registration Motor Problem.
During initial rotations home position is not
detected within 106 pulses. When the rear side
home position sensor is turned off during
initialization, the sensor did not turn on within 3
sec.
C8190 DF-720 Trailing Edge Registration Motor Problem.
During initial rotations home position is not
detected within 106 pulses. When the trailing edge
home position sensor is turned off during
initialization, the sensor did not turn on within 3
sec.
C8210 DF-710 Stapler Moving Motor 1 Error. During initial
rotations home position is not detected within 1.5
sec.
C8210 DF-720 Finisher Stapler Problem. Stapler home
position sensor does not change state from non-
detect to detect within 200ms of forward (CCW)
rotation. During initial rotations stapler home
position detection does not change state from non-
detect to detect within 600ms of reverse (CW)
rotation.
C8210 DF-730 Stapler Problem. Home position is not
detected within a specific time of activation.
C8220 DF-710 Stapler Moving Motor 2 Error. During initial
rotations home position is not detected within 3.5
sec.
C8230 DF-710 Stapler Motor Problem. Jam 82 is indicated.
C8300 BF-710 Centerfold Unit Communiation Error.
Although the connection is detected, communication
is not possible with the centerfold unit.
C8310 BF-710 Centerfold Side Registration Motor 1
Problem. During initial rotations home position is
not detected within 1000ms.
C8320 BF-710 Centerfold Paper Conveying Belt Motor
Problem. During initial rotations home position is
not detected within 2500ms.
C8330 BF-710 Blade Motor Problem. During initial rotations
home position is not detected within 1500ms.
C8340 BF-710 Centerfold Staple Motor Problem. Jam 89.
C8350 BF-710 Centerfold Side Registration Motor 2
Problem. During initial rotations home position is
not detected within 1000ms.
C8360 BF-710 Centerfold Main Motor Problem. The motor
lock signal is detected for more than 1000ms during
activation.
C8440 DF-730 Sensor Adjusting Problem. The paper entry
sensor cannot be adjusted within the specified
range.
C8460 DF-730 EEPROM Problem. Reading to or writing
from EEPROM cannot be performed.
C8500 MT-710 Communication Error. The connection is
detected, but communication is not possible with
the mailbox.
C8510 MT-710 Drive Motor Problem. The motor lock signal
is detected for more than 500ms during activation.
C8800 DF-710 Communication Problem. No
communication: there is no reply after (5) tries.
Abnormal communication: a parity or checksum
error is detected (5) times in succession.
C8900 DF-710 Backup Memory Data Problem. Read and
write data does not match.
C8910 PH-5A Backup Memory Data Problem. Read and
write data does not match.
C8920 MT-710 Backup Memory Data Problem. Read and
write data does not match.
C8930 BF-710 Backup Memory Data Problem. Read and
write data does not match.
C9000 DP-700 Communication Problem. A communication
error is detected.
C9040 DP-700 Lift Motor Ascent Error. The DP lift upper
limit switch is not detected within 10000 pulses.
After a one time retry, the DP lift upper limit switch
could not be turned On.
C9050 DP-700 Lift Motor Descent Error. The DP lift lower
limit switch is not detected within 10000 pulses.
After a one time retry, the DP lift lower limit switch
could not be turned On.
C9060 DP-700 EEPROM Error. Read and write data does
not match. Data in the specified area of the backup
memory does not match the specified values.
C9070 DP-700 Communication Error between the DP and
SHD. A communication error is detected.
C9080 DP-700 Communication Error between the DP and
CIS. Reading cannot be performed correctly.
CF000 Operation Panel PWB Communication Error/System
Error. Unknown error. Communication error
between panel and main controller. (If CF620
occurred and is left, CF000 also occurred because of
timeout control.
CF010 Main PWB Checksum Error/System Error.
Communication error between panel and main
controller.
CF020 Memory Checksum Error/Operation System Error.
CF030 Main PWB System Error.
CF040 Engine PWB Communication Error.
CF041 Scanner PWB Communication Error.
CF050 Engine ROM Checksum Error.
CF060 Engine RAM Error.
CF070 Flash ROM Error. Defective flash ROM (which?).
CF080 Flash ROM Error (during download). Defective flash
ROM (which?).
CF090 Fax System M Communication Error.
CF14F Power Source Secondary Side Error/Operation
System Error. The operation decomes unstable after
recovering the power supply fail (brownout or
power drop). Wall voltage is unstable or the main
power supply switch was turned OFF/ON within 1
sec.
CF256 Fax System M IOBL error or KUIOLIB error. Poor
contact at the fax card card due to mis-installation.
CF257 Fax System M IOBL error or KUIOLIB error. Poor
contact at the fax card card due to mis-installation.
CF26F Print System Other Errors. Bug of v.2.03B has been
fixed by v. 2.04A (Booklet > Booklet Print).
CF3xx Undefined.
CF423 Fax System M Error. Wrong data or value detected
when the following function is used. Or poor contact
at fax card due to mis-installation.
CF423 Fax System M Error. The IF error detects during
system authentication from ACT_Account_Manager.
Or poor contact at fax card due to mis-installation.
CF433 CF434
CF437 CF43F
CF441 CF444
CF445 CF451
HDD Image Process Error. Destruction of stored
jobs on the HDD. It may occur when selecting the
keys for calling stored copy or scanner job from a
custom box.
CF45F CF453
CF454 CF45F
CF460 CF463
CF46F CF470
HDD Image Process Error. Destruction of stored
jobs on the HDD. It may occur when selecting the
keys for calling stored copy or scanner job from a
custom box.
CF473 CF47F
CF484 CF487
CF48F CF490
CF493 CF494
HDD Image Process Error. Destruction of stored
jobs on the HDD. It may occur when selecting the
keys for calling stored copy or scanner job from a
custom box.
CF5xx Undefined.
CF610 System Start Error.
CF620 System Error. Error acquiring the event data. Panel
detects CF000 as same error.
CF620 System Error. Error acquiring the event data. Panel
detects CF000 as same error. Unable to Load Files
To CF Card.
CF7D7 Readout Error of SSL (authentication data).
CFAxx HDD Error.
CFB2C CFB30
CFB31
Panel Error. NetFont error. Communication error
between panel and main controller during
initialization or rejection of communication by
controller during initialization. Blue Screen of Death.
CFB30 Incompatible Level Of Firmware on Main EEPROM.
CFB31 Corrupt Firmware on Main EEPROM.
CFB32 Panel Error. Timeout request for start up command.
Start command hasn't been received. Possible
destruction of system file in HDD. Cannot enter
maintenance mode. Blue Screen of Death.
CFB33 Panel Error. Detects disconnection with controller.
Possible overdrive of control board or destruction of
system file in HDD. Cannot enter maintenance
mode. Blue Screen of Death.
F000 Operation Panel PWB Communication Error.
F010 Main PWB Checksum Error.
F020 Memory Checksum Error.
F030 Main PWB System Error.
F040 Engine PWB Communication Error.
F041 Scanner PWB Communication Error.
F050 Engine ROM Checksum Error.
F060 Engine RAM Error.
F070 Flash ROM Error.
F080 Flash ROM Error (during download).
F090 Fax Control PWB Communication Error.
F14F Power Source PWB Second Side Error.
E00000 or U00000 Fax Communication Error: No response or line busy
after the set number of redials.
E00100 or U00100 Fax Communication Error: Transmission was
interruped by a press of the Stop/Clear key.
E00200 or U00200 Fax Communication Error: Reception was
interrupted by a press of the Stop/Clear key.
E00300 or U00300 Fax Communication Error: Recording paper on the
destination unit has run out during reception.
E00420 or U00420 Fax Communication Error: A relay request was
received from the host center but interrupted
because of a mismatch in permit ID or telephone
number.
E00421 or U00421 Fax Communication Error: Subaddress-based relay
reception was interrupted because of a mismatch in
the specified subaddress relay box number.
E00430 or U00430 Fax Communication Error: Polling request
(confidential or reverse polling) was received but
interrupted because of a mismatch in the permit
number.
E00430 or U00430 Fax Communication Error: Subaddress-based
bulletin board transmission was interrupted because
of a mismatch in the permit ID of the transmitting
unit.
E00431 or U00431 Fax Communication Error: Confidential polling
transmission was interrupted because the specified
confidential box number was not registered.
E00431 or U00431 Fax Communication Error: A subaddress-based
bulletin board transmission was interrupted because
the specified subaddress confidential box was not
registered.
E00432 or U00432 Fax Communication Error: Confidential polling
transmission was interrupted because of a
mismatch in the confidential box ID number.
E00432 or U00432 Fax Communication Error: A subaddress-based
bulletin board transmission was interrupted because
of a mismatch in the subaddress confidential box
number.
E00433 or U00433 Fax Communication Error: Confidential polling
request was received but data was not present in
the confidential box.
E00433 or U00433 Fax Communication Error: Subaddress-based
bulletin board transmission request was received
but data was not present in the subaddress
confidential box.
E00434 or U00434 Fax Communication Error: Confidential polling
request was received but interrupted because the
specified confidential box number was intended for
encryption.
E00435 or U00435 Fax Communication Error: Confidential polling
request was received but interrupted because the
specified confidential box was being accessed.
E00435 or U00435 Fax Communication Error: Subaddress-based
bulletin board transmission request was received
but interrupted because the specific subaddress
confidential box was being accessed.
E00440 or U00440 Fax Communication Error: Confidential reception
was interrupted because the specified confidential
box number was not registered.
E00440 or U00440 Fax Communication Error: Subaddress-based
confidential reception or subaddress-based relay
reception was interrupted because the specific
subaddress box was not registered.
E00440 or U00440 Fax Communication Error: Subaddress-based
confidential reception or subaddress-based relay
command reception was interrupted because the
specific subaddress box number was being
accessed.
E00441 or U00441 Fax Communication Error: Confidential reception
was interrupted because the specified confidential
box number was intended for encryption.
E00450 or U00450 Fax Communication Error: The destination
transmitter disconnected because the permit IDs
did not agree while the destination transitter is in
password-check transmission or restricted
transmission.
E00460 or U00460 Fax Communication Error: Encrypted reception was
interrupted because the specified encryption box
number was not registered.
E00460 or U00460 Fax Communication Error: Ecrypted reception
request was received but interrupted because the
specified encryption box was being accessed.
E00462 or U00462 Fax Communication Error: Ecryption reception was
interrupted because the encryption key for the
specified encryption box was not registered.
E00500 or U00500 Fax Communication Error: Multiple communication
was interrupted and the call was not made on
destination units after interruption.
E00600 or U00600 Fax Communication Error: The document processor
cover is open.
E00601 or U00601 Fax Communication Error: Document jam or the
document length exceeds the maximum.
E00602 or U00602 Fax Communication Error: Image scanning section
problem
E00603 or U00603 Fax Communication Error: No document feed.
E00604 or U00604 Fax Communication Error: Document length
exceeded the limit of the bitmap memory capacity.
E00610 or U00610 Fax Communication Error: Recording section cover
open.
E00611 or U00611 Fax Communication Error: Recording paper jam.
E00613 or U00613 Fax Communication Error: Image writing section
problem.
E00614 or U00614 Fax Communication Error: Nearly empty of
recording paper.
E00615 or U00615 Fax Communication Error: Empty of recording
paper.
E00620 or U00620 Fax Communication Error: Copier fixing unit
problem.
E00622 or U00622 Fax Communication Error: Copier drive motor
problem.
E00655 or U00655 Fax Communication Error: CTS was not activated
after RTS due to a modem error.
E00656 or U00656 Fax Communication Error: Data was not transmitted
after CTS was activated due to a modem error.
E00670 or U00670 Fax Communication Error: Power was cut off during
communication.
E00677 or U00677 Fax Communication Error: There was no file to
transmit in the memory transmission mode.
E00690 or U00690 Fax Communication Error: System error.
E00700 or U00700 Fax Communication Error: Communication was
interrupted because of a problem in the destination
unit.
E00800 or U00800 Fax Communication Error: A page transmission
error occurred in G3 mode, because of reception of
a RTN or PIN signal.
E00810 or U00810 Fax Communication Error: A page transmission
error re-occurred in G3 mode after retry of
transmission in ECM mode.
E00900 or U00900 Fax Communication Error: A page reception error
occurred in G3 mode. An RTN or PIN signal was
transmitted because of a page reception error.
E00910 or U00910 Fax Communication Error: A page reception error
occurred in G3 mode. A page reception error
remained after retry of transmission in ECM mode.
E01000 or U01000 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. An FTT signal was
received for a set number of times after TCF signal
transmissions at 2400bps.
E01000 or U01000 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. An RTN signal
was received in response to a Q signal (excluding
EOP) after transmission at 2400bps.
E01001 or U01001 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. The function of
the unit differs from that indicated by a DIS signal.
E01010 or U01010 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. No relevant signal
was received after transmission of a DNL (MPS or
EOM) signal, and the preset number of command
retransfers was exceeded (between units of our
make).
E01011 or U01011 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. No relevant signal
was received after transmission of a DCS, TCF
signal, and the preset number of command
retransfers was exceeded.
E01012 or U01012 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. No relevant signal
was received after transmission of an NSS1, NSS2
(TCF) signal, and the preset number of command
retransfers was exceeded (between units of our
make).
E01013 or U01013 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. No relevant signal
was received after transmission of an NSS3, TCF
signal, and the preset number of command
retransfers was exceeded (between units of our
make).
E01014 or U01014 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. No relevant signal
was received after transmission of an MPS signal,
and the preset number of command retransfers was
exceeded.
E01015 or U01015 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. No relevant signal
was received after transmission of an EOM signal,
and the preset number of command retransfers was
exceeded.
E01016 or U01016 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. An MCF signal
was received but no DIS signal was received after
transmission of an EOM signal, and T1 timeout was
detected.
E01017 or U01017 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. No relevant signal
was received after transmission of an EOP signal,
and the preset number of command retransfers was
exceeded.
E01018 or U01018 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. No relevant signal
was received after transmission of a PRI-EOP signal,
and the preset number of command retransfers was
exceeded.
E01019 or U01019 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. No relevant signal
was received after transmission of a CNC signal,
and the preset number of command retransfers was
exceeded (between units of our make).
E01020 or U01020 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. No relevant signal
was received after transmission of a CTC signal, and
the preset number of command retransfers was
exceeded (ECM).
E01021 or U01021 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. No relevant signal
was received after transmission of an EOR.Q signal,
and the preset number of command retransfers was
exceeded (ECM).
E01022 or U01022 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. No relevant signal
was received after transmission of a RR signal, and
the preset number of command retransfers was
exceeded (ECM).
E01023 or U01023 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. No relevant signal
was received after transmission of a PS.NULL signal,
and the preset number of command retransfers was
exceeded (ECM).
E01024 or U01024 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. No relevant signal
was received after transmission of a PPS.MPS
signal, and the preset number of command
retransfers was exceeded (ECM).
E01025 or U01025 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. No relevant signal
was received after transmission of a PPS.EOM
signal, and the preset number of command
retransfers was exceeded (ECM).
E01026 or U01026 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. No relevant signal
was received after transmission of a PPS.EOP signal,
and the preset number of command retransfers was
exceeded (ECM).
E01027 or U01027 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. No relevant signal
was received after transmission of a PPS.PRI-EOP
signal, and the preset number of command
retransfers was exceeded (ECM).
E01028 or U01028 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. T5 timeout was
detected during ECM Transmission (ECM).
E01040 or U01040 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. A DCN or other
inappropriate signal was received during standby for
DIS signal reception.
E01041 or U01041 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of a DNL (MPS or EOM)
signal (between units of our make).
E01042 or U01042 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of a DCS, TCF signal.
E01043 or U01043 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of an NSS1, NSS2 (TCF)
signal (between units of our make).
E01044 or U01044 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of an NSS3, TCF signal
(between units of our make).
E01045 or U01045 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. A DCN or other
inappropriate signal was received after transmission
of an MPS signal.
E01046 or U01046 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. A DCN or other
inappropriate signal was received after transmission
of an EOM signal.
E01047 or U01047 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. A DCN or other
inappropriate signal was received after transmission
of an EOP signal.
E01048 or U01048 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of a PRI-EOP signal.
E01049 or U01049 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of a CNC signal
(between units of our make).
E01050 or U01050 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of a CTC signal (ECM).
E01051 or U01051 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of an EOR.Q signal
(ECM).
E01052 or U01052 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of an RR signal (ECM).
E01053 or U01053 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of a PPS.NULL signal
(ECM).
E01054 or U01054 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of a PPS.MPS signal
(ECM).
E01055 or U01055 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of a PPS.EOM signal
(ECM).
E01056 or U01056 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of a PPS.EOP signal
(ECM).
E01057 or U01057 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of a PPS.PRI-EOP signal
(ECM).
E01070 or U01070 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. Polarity reversal
was detected during handshake.
E01071 or U01071 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. Polarity reversal
was detected during message transmission.
E01072 or U01072 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. A break in loop
current was detected during transmission.
E01073 or U01073 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. During reverse
polling in V.34 mode at the receiver unit, a CM
signal was not detected when transmitting after
reception.
E01080 or U01080 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. A PIP signal was
received after transmission of a PPS.NULL signal.
E01091 or U01091 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. During
transmission in V.34 mode, communication was
interrupted because a PPR signal was received over
(10) times even after reducing the communication
speed to the minimum with the symbol speed
maintained at the level of connection.
E01092 or U01092 Fax Communication Error: Transmission in G3 mode
was interrupted by a signal error. During
transmission in V.34 mode, communication was
interrupted because of an impossible combination of
the symbol speed and communication speed.
E01100 or U01100 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. Function of the
unit differs from that indicated by a DCS signal.
E01101 or U01101 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. Function of the
unit (excl. communication mode select) differs from
that indicated by an NSS signal.
E01102 or U01102 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. A DTC (NSC)
signal was received when no transmission data was
in the unit.
E01110 or U01110 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. No response after
transmission of a DIS signal.
E01111 or U01111 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. No response after
transmission of a DTC (NSC) signal.
E01112 or U01112 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. No training
reception after reception of a DCS or NSS signal.
E01113 or U01113 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. No response after
transmission of an FTT signal.
E01114 or U01114 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. No message
reception after transmission of a CFR signal.
E01115 or U01115 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. No message
reception after transmission of an MCF signal.
E01116 or U01116 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. No message
reception after transmission of a PPR signal.
E01117 or U01117 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. No message
reception after transmission of a CTR signal.
E01118 or U01118 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. No message
reception after transmission of an ERR signal.
E01119 or U01119 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. No further signals
were received after reception of a message.
E01120 or U01120 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. No response after
transmission of an MCF signal.
E01121 or U01121 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. No response after
transmission of an RTP signal.
E01122 or U01122 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. No response after
transmission of an RTN signal.
E01123 or U01123 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. No response after
transmission of a PIP signal.
E01124 or U01124 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. No response after
transmission of a PIN signal.
E01125 or U01125 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. No response after
transmission of a CNS signal (between units of our
make).
E01126 or U01126 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. No response after
transmission of a PPR signal (ECM).
E01127 or U01127 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. No response after
transmission of an ERR signal (ECM).
E01128 or U01128 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. No response after
transmission of an RNR signal (ECM).
E01129 or U01129 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. No response after
transmission of an SPA signal (short protocol).
E01140 or U01140 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of a DIS signal.
E01141 or U01141 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of a DTC signal.
E01142 or U01142 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of a DCS or NSS signal.
E01143 or U01143 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of an FTT signal.
E01144 or U01144 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of a CFR signal.
E01145 or U01145 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. A DCN signal was
received after reception of a message.
E01146 or U01146 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of an MCF signal
(interoffice communication after reception of an
MPS, EOM signal or confidential interoffice
communication).
E01147 or U01147 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of an RTP signal.
E01148 or U01148 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of an RTN signal.
E01149 or U01149 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of a PIPsignal.
E01150 or U01150 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of a PIN signal.
E01151 or U01151 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of a PPR signal (ECM).
E01152 or U01152 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of a CTR signal (ECM).
E01153 or U01153 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of an ERR signal (ECM).
E01154 or U01154 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of an PNP signal (ECM).
E01155 or U01155 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. A DCN signal was
received after transmission of an SPA signal (short
protocol).
E01160 or U01160 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. During message
reception, transmission time exceeded the
maximum transmission time per line.
E01161 or U01161 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. Number of error
lines exceeded limits during message reception.
E01162 or U01162 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. A break in loop
current was detected during message reception.
E01163 or U01163 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. Polarity reversal
was detected during message reception.
E01164 or U01164 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. One page length
exceeded the specified length during message
reception.
E01170 or U01170 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. A decoding error
occurred during MMR message reception.
E01172 or U01172 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. During reverse
polling in V.34 mode at the transmitting unit, a JM
signal was not detected after transmission of a CM
signal when receiving after transmission.
E01191 or U01191 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. Communication
was interrupted because an error occurred during
an image data reception sequence in the V.34
mode.
E01199 or U01199 Fax Communication Error: Reception in G3 mode
was interrupted by a signal error. A DIS signal with
different FIF was received after transmission of a
DIS signal.
E01400 or U01400 Fax Communication Error: An invalid one-touch key
was specified during communication.
E01500 or U01500 Fax Communication Error: A communication error
occurred when calling in V.8 mode.
E01600 or U01600 Fax Communication Error: A communication error
occurred when called in V.8 mode.
E01700 or U01700 Fax Communication Error: A communication error
occurred in phase 2 (line probing) in the period
after transmission of INFO0, before entering phase
3 (primary channel equivalent device training),
before starting T.30 protocol, during transmission in
V.34 mode. For example: INFO0/A/Abar (B/Bbar,
for polling transmission)/INFOh was not detected.
E01720 or U01720 Fax Communication Error: A communication error
occurred in phase 4 (modem parameter exchange)
in the period after initiating the control channel,
before starting T.30 protocol, during transmission in
V.34 mode. For example: PPh/ALT/MPh/E was not
detected.
E01721 or U01721 Fax Communication Error: A communication error
occurred before starting T.30 protocol during
transmission in V.34 mode. Operation was
interrupted due to the absence of a common
communication speed between the units. 1) A DCN
signal was received from the destination unit and
the line was cut, or 2) a DIS (NSF, CSI) signal was
received from the destination unit and in response
to the signal, the unit transmitted a DCN signal and
the line was cut.
E01800 or U01800 Fax Communication Error: A communication error
occurred in phase 2 (line probing) in the period
after transmission of INFO0, before entering phase
3 (primary channel equivalent device training),
before starting T.30 protocol during reception in
V.34 mode. For example: INFO0/B/Bbar (A/Abar,
for polling reception)/probing tone was not
detected.
E01810 or U01810 Fax Communication Error: A communication error
occurred in phase 3 (primary channel equivalent
device training), before starting T.30 protocol
during reception in V.34 mode. For example:
S/Sbar/PP/TRN was not detected.
E01820 or U01820 Fax Communication Error: A communication error
occurred in phase 4 (modem parameter exchange)
in the period after initiating the control channel,
before starting T.30 protocol during reception in
V.34 mode. For example: PPh/ALT/MPh/E was not
detected.
E02000 or U02000 Fax Communication Error: Relay broadcast was
refused by a relay station because of a mismatch in
permit ID number and permit telephone number
when a relay command was used.
E02100 or U02100 Fax Communication Error: A relay command failed
because the destination unit (relay station) had no
relay broadcast capability.
E02200 or U02200 Fax Communication Error: A relay command from a
command station failed because a telephone
number was not registered in the relay station was
specified.
E02200 or U02200 Fax Communication Error: Relay broadcast was
requested to a relay station but failed because a
telephone number was not registered in the relay
station was specified.
E02200 or U02200 Fax Communication Error: Subaddress-based relay
broadcast transmission failed because the data
registered in the subaddress relay box was deleted.
E02303 or U02303 Fax Communication Error: Receiving station
information was not normally received in reception
of a relay command. Timeout was detected before a
correct DNL signal was received.
E02304 or U02304 Fax Communication Error: Receiving station
information was not normally received in reception
of a relay command. A signal other than MPS or
EOM signal was received after a DNL signal was
received.
E02400 or U02400 Fax Communication Error: An interoffice
subaddress-based relay transmission was
interrupted because of a mismatch in the specified
relay box number.
E03000 or U03000 Fax Communication Error: No document was
present in the destination unit when polling
reception started.
E03100 or U03100 Fax Communication Error: In reverse polling,
although no original was set in the destination unit,
transmission was complete.
E03200 or U03200 Fax Communication Error: In confidential polling
reception, data was not accumulated in the
specified box in the destination unit.
E03200 or U03200 Fax Communication Error: In interoffice
subaddress-based bulletin board reception, data
was not stored in the box specified by the
destination unit.
E03300 or U03300 Fax Communication Error: In polling reception from
a unit of our make, operation was interrupted due
to a mismatch in permit ID number or telephone
number.
E03300 or U03300 Fax Communication Error: In interoffice
subaddress-based bulletin board reception,
operation was interrupted due to a mismatch in
permit ID number or telephone number.
E03400 or U03400 Fax Communication Error: Polling reception was
interupted because of a mismatch in individual
numbers.
E03500 or U03500 Fax Communication Error: In confidential polling
reception, the specified confidential box number
was not registered in the destination.
E03500 or U03500 Fax Communication Error: In interoffice
subaddress-based bulletin board reception, the
specified subaddress confidential box number was
not registered in the destination unit.
E03500 or U03500 Fax Communication Error: The destination was
being accessed.
E03600 or U03600 Fax Communication Error: Confidential polling
reception was interrupted because of a mismatch in
specified confidential box numbers.
E03600 or U03600 Fax Communication Error: An interoffice
subaddress-based bulletin board reception was
interrupted because of a mismatch in the specified
subaddress confidential box number.
E03700 or U03700 Fax Communication Error: Confidential polling
reception failed because the destination unit had no
confidential polling transmission capability or data
was not accumulated in any box in the destination
unit.
E03700 or U03700 Fax Communication Error: Interoffice subaddress-
based bulletin board reception failed because the
destination unit had no subaddress-based bulletin
board transmission capability, or data was not
stored in any subaddress confidental box in the
destination unit.
E04000 or U04000 Fax Communication Error: The confidential box
specified for confidential transmission was not
registered in the destination unit.
E04000 or U04000 Fax Communication Error: In interoffice
subaddress-based transmission mode, the specified
subaddress box number was not registered in the
destination unit.
E04000 or U04000 Fax Communication Error: The destination was
being accessed.
E04100 or U04100 Fax Communication Error: Confidential transmission
failed because the destination unit had no
confidential capability.
E04100 or U04100 Fax Communication Error: Subaddress-based
transmission failed because the destination unit had
no subaddress-based reception capability.
E04200 or U04200 Fax Communication Error: In encrypted
tranmission, the specified encryption box was not
registered in the destination unit.
E04300 or U04300 Fax Communication Error: Encrypted transmission
failed because the destination unit had no encrypted
communication capability.
E04400 or U04400 Fax Communication Error: Communication was
interrupted because of an encryption key error
during encrypted transmission. Encryption keys did
not agree.
E04401 or U04401 Fax Communication Error: Communication was
interrupted because of an encryption key error
during encrypted trasmission. The encryption key
was not registered.
E04500 or U04500 Fax Communication Error: Encrypted reception was
interrupted because of a mismatch in ecryption
keys.
E05000 or U05000 Fax Communication Error: In transmission with a
specified number, the set number of originals was
different from the number of transmitted originals.
E05100 or U05100 Fax Communication Error: Password check
transmission or restricted transmission was
interrupted because the permit ID numbers did not
match.
E05200 or U05200 Fax Communication Error: Password check
reception or restricted reception was interrupted
because the permit ID numbers did not match, the
rejected fax numbers did match, or the destination
receiver did not return its phone number.
E05300 or U05300 Fax Communication Error: Password check
reception or restricted reception was interrupted
because the permitted numbers did not match, the
rejected numbers did match, or the machine in
question did not acknowledge its phone number.
E09000 or U09000 Fax Communication Error: G3 communication was
attempted but failed because the destination unit
was a G2 machine.
E12000 or U12000 Fax Communication Error: Relay broadcast was
requested from a command station but memory
overflowed during reception.
E12000 or U12000 Fax Communication Error: In subaddress-based
relay reception memory overflowed.
E12100 or U12100 Fax Communication Error: Relay was commanded
but memory overflowed in the destination unit
(relay station).
E14000 or U14000 Fax Communication Error: Memory overflowed
during confidential reception.
E14000 or U14000 Fax Communication Error: Memory overflowed in
subaddress-based confidential reception.
E14100 or U14100 Fax Communication Error: Memory overflowed in
the destination unit during confidential
transmission.
E14100 or U14100 Fax Communication Error: Memory overflowed in
the destination unit during interoffice subaddress-
based transmission.
E19000 or U19000 Fax Communication Error: Memory overflowed
during memory reception.
E19100 or U19100 Fax Communication Error: Memory overflowed in
the destination unit during transmission.
E19200 or U19200 Fax Communication Error: Memory transmission
failed because a decoding error occurred.
E19300 or U19300 Fax Communication Error: Transmission failed
because an error occurred during JBIG encoding.
E19400 or U19400 Fax Communication Error: Reception failed because
an error occurred during JBIG encoding.
Send SMB Error
1102
Error: Username/Password or Shared Name/Folder
Name. Domain name is not entered.
Send SMB Error
1102
Error: Username/Password or Shared Name/Folder
Name. Assign disable user/password.
Send SMB Error
1102
Error: Username/Password or Shared Name/Folder
Name. Assign the user who is not allowed to access
the folder.
Send SMB Error
1102
Error: Username/Password or Shared Name/Folder
Name. Assign disable shared name.
Send SMB Error
1102
Error: Username/Password or Shared Name/Folder
Name. Host name error.
Send SMB Error
1103
Error: Pathname or File Name. Domain name is not
entered.
Send SMB Error
1103
Error: Pathname or File Name. Connect to the folder
which is not permitted for reference/writing.
Send SMB Error
1103
Error: Pathname or File Name. Assign disable folder
path.
Send SMB Error
1105
Error: Not Supported Protocol. SMB protocol is set
to OFF.
Send SMB Error
2101
Error: Can Not Connect. Enter the disable host
name/IP address.
Send SMB Error
2101
Error: Can Not Connect. Assign the wrong port
number.
Send SMB Error
2101
Error: Can Not Connect. Network is not connected.
Send SMB Error
2103
Error: Response Wait With Timeout. The server is
unable to communicate.
Send SMB Error
2201
Error: Network Transfer. Error occurs on the
network.
Send SMB Error
2203
Error: Response Wait With Timeout. Response is not
returned from the server, above specified time.
Send SMB Error
9181
Error: Page Max Count Over. The number of pages
of a send file exceeds 999 pages.
Send FTP Error
1101
Error: Host Name. Enter the disable host name/IP
address.
Send FTP Error
1102
Error: Username/Password. Domain name is not
entered.
Send FTP Error
1102
Error: Username/Password. Assign disable
user/password.
Send FTP Error
1103
Error: Pathname or File Name. Connect to the folder
which is not permitted for reference/writing.
Send FTP Error
1103
Error: Pathname or File Name. Assign disable folder
path.
Send FTP Error
1105
Error: Not Supported Protocol. FTP protocol is set to
OFF.
Send FTP Error
2101
Error: Can Not Connect. Enter the disable host
name/IP address.
Send FTP Error
2101
Error: Can Not Connect. Assign the wrong port
number.
Send FTP Error
2101
Error: Can Not Connect. Network is not connected.
Send FTP Error
2102
Error: Cannot Connect With Timeout. The server is
unable to communicate.
Send FTP Error
2102
Error: Cannot Connect With Timeout. Send the
server which does not support FTP server.
Send FTP Error
2103
Error: Response Wait With Timeout. The server is
unable to communicate.
Send FTP Error
2201
Error: Network Transfer. Error occurs on the
network.
Send FTP Error
2202
Error: Network Transfer With Timeout. Error occurs
on the network.
Send FTP Error
2203
Error: Response Wait With Timeout. Response is not
returned from the server, above specified time.
Send FTP Error
3101
Error: Server Response. The server is error status.
Send FTP Error
9181
Error: Page Max Count Over. The number of pages
of a send file exceeds 999 pages.
Send email Error
1101
Error: Host Name. SMTP server name is not set.
Error SMTP server name.
Send email Error
1102
Error: Username/Password. User ID for the
authentication is not entered or entered wrongly.
Wrong authentication password is entered.
Send email Error
1104
Error: No Recipient Address. The destination
address is not specified.
Send email Error
1105
Error: Not Supported Protocol. SMTP protocol is set
to OFF.
Send email Error
1106
Error: No Sender Info. Sender address is not
entered.
Send email Error
2101
Error: Can Not Connect. Select [Other Authenticate]
when authenticating POP before SMTP.
Send email Error
2101
Error: Can Not Connect. The specified server is not
SMTP server.
Send email Error
2101
Error: Can Not Connect. Network is not connected.
Send email Error
2102
Error: Cannot Connect With Timeout. The server is
unable to communicate.
Send email Error
2103
Error: Response Wait With Timeout. The server is
unable to communicate.
Send email Error
2201
Error: Network Transfer. Error occurs on the
network.
Send email Error
2202
Error: Network Transfer With Timeout. Error occurs
on the network.
Send email Error
2203
Error: Response Wait With Timeout. Response is not
returned from the server, above specified time.
Send email Error
2204
Error: Email Size Limit. The size of the email
attachment exceeds its limit.
Send email Error
3101
Error: Server Response. The server is error status.
Send email Error
3101
Error: Server Response. Server setting is not
authenticated normally.
Send email Error
3201
Error: Not Found Authentication Mechanism.
Unsupported SMTP Authentication Mechanism is
found.
Send email Error
9181
Error: Page Max Count Over. The number of pages
of a send file exceeds 999 pages.
TWAIN Error 2202 Error: Network Transfer With Timeout. Response is
not returned from the server, above the specified
time.
TWAIN Error 9181 Error: Page Max Count Over. The number of pages
of a send file exceeds 999 pages.
Software Error
5101
Error: Not Yet Connected. Operation handle error.
Error for stored status in the operation handle.
Software Error
5102
Error: Already Connected. Operation handle error.
Error for stored status in the operation handle.
Software Error
5103
Error: Not Yet Opened. Error for storage status in
the operation handle.
Software Error
5104
Error: Already Opened. Error for storage status in
the operation handle.
Software Error
7101
Error: Memory Allocation. Insufficient memory
space.
Software Error
7102
Error: Socket Create. Unable to create a
communication socket.
Software Error 720f Error: Unknown Error. Unable to determine the
cause.
Send error. Job is
cancelled. Press
[End]. 1101
Send Email Error: Host Name. SMTP server name is
not set. Error SMTP server name.
Send error. Job is
cancelled. Press
[End]. 1101
Send FTP Error: Host Name. Enter the disable host
name/IP address.
Send error. Job is
cancelled. Press
[End]. 1102
Send Email Error: Username/Password. User ID for
the authentication is not entered or entered
wrongly. Wrong authentication password is entered.
Send error. Job is
cancelled. Press
[End]. 1102
Send SMB/FTP Error: Username/Password or
Shared Name/Folder Name. Domain name is not
entered.
Send error. Job is
cancelled. Press
[End]. 1102
Send SMB/FTP Error: Username/Password or
Shared Name/Folder Name. Assign disable
user/password.
Send error. Job is
cancelled. Press
[End]. 1102
Send SMB Error: Username/Password or Shared
Name/Folder Name. Assign disable shared name.
Send error. Job is
cancelled. Press
[End]. 1102
Send SMB Error: Username/Password or Shared
Name/Folder Name. Host name error.
Send error. Job is
cancelled. Press
[End]. 1103
Send SMB/FTP Error: Pathname or File Name.
Domain name is not entered.
Send error. Job is
cancelled. Press
[End]. 1103
Send SMB/FTP Error: Pathname or File Name.
Connect to the folder which is not permitted for
reference/writing.
Send error. Job is
cancelled. Press
[End]. 1103
Send SMB/FTP Error: Pathname or File Name.
Assign disable folder path.
Send error. Job is
cancelled. Press
[End]. 1104
Send Email Error: No Recipient Address. The
destination address is not specified.
Send error. Job is
cancelled. Press
[End]. 1105
Send Email Error: Not Supported Protocol. SMTP
protocol is set to OFF.
Send error. Job is
cancelled. Press
[End]. 1105
Send SMB Error: Not Supported Protocol. SMB
protocol is set to OFF.
Send error. Job is
cancelled. Press
[End]. 1105
Send FTP Error: Not Supported Protocol. FTP
protocol is set to OFF.
Send error. Job is
cancelled. Press
[End]. 1106
Send Email Error: No Sender Info. Sender address
is not entered.
Send error. Job is
cancelled. Press
[End]. 2101
Send Email Error: Can Not Connect. Network is not
connected.
Send error. Job is
cancelled. Press
[End]. 2101
Send Email Error: Can Not Connect. Select [Other
Authenticate] when authenticating POP before
SMTP.
Send error. Job is
cancelled. Press
[End]. 2101
Send Email Error: Can Not Connect. The specified
server is not SMTP server.
Send error. Job is
cancelled. Press
[End]. 2101
Send SMB/FTP Error: Can Not Connect. Enter the
disable host name/IP address.
Send error. Job is
cancelled. Press
[End]. 2101
Send SMB/FTP Error: Can Not Connect. Assign the
wrong port number.
Send error. Job is
cancelled. Press
[End]. 2101
Send SMB/FTP Error: Can Not Connect. Network is
not connected.
Send error. Job is
cancelled. Press
[End]. 2102
Send Email/ FTP Error: Cannot Connect With
Timeout. The server is unable to communicate.
Send error. Job is
cancelled. Press
[End]. 2102
Send FTP Error: Cannot Connect With Timeout.
Send the server which does not support FTP server.
Send error. Job is
cancelled. Press
[End]. 2103
Send Email/ SMB/ FTP Error: Response Wait With
Timeout. The server is unable to communicate.
Send error. Job is
cancelled. Press
[End]. 2201
Send Email/ SMB/ FTP Error: Network Transfer.
Error occurs on the network.
Send error. Job is
cancelled. Press
[End]. 2202
Send Email/FTP Error: Network Transfer With
Timeout. Error occurs on the network.
Send error. Job is
cancelled. Press
[End]. 2202
Send TWAIN Error: Network Transfer With Timeout.
Response is not returned from the server, above the
specified time.
Send error. Job is
cancelled. Press
[End]. 2203
Send Email/FTP Error: Response Wait With Timeout.
Response is not returned from the server, above
specified time.
Send error. Job is
cancelled. Press
[End]. 2204
Send Email Error: Email Size Limit. The size of the
email attachment exceeds its limit.
Send error. Job is
cancelled. Press
[End]. 3101
Send Email/FTP Error: Server Response. The server
is error status.
Send error. Job is
cancelled. Press
[End]. 3101
Send Email Error: Server Response. Server setting
is not authenticated normally.
Send error. Job is
cancelled. Press
[End]. 3201
Send Email Error: Not Found Authentication
Mechanism. Unsupported SMTP Authentication
Mechanism is found.
Send error. Job is
cancelled. Press
[End]. 5101
Send Software Error: Not Yet Connected. Operation
handle error. Error for stored status in the operation
handle.
Send error. Job is
cancelled. Press
[End]. 5102
Send Software Error: Already Connected. Operation
handle error. Error for stored status in the operation
handle.
Send error. Job is
cancelled. Press
[End]. 5103
Send SoftwareError: Not Yet Opened. Error for
storage status in the operation handle.
Send error. Job is
cancelled. Press
[End]. 5104
Send Software Error: Already Opened. Error for
storage status in the operation handle.
Send error. Job is
cancelled. Press
[End]. 7102
Send Software Error: Socket Create. Unable to
create a communication socket.
Send error. Job is
cancelled. Press
[End]. 720f
Send Software Error: Unknown Error. Unable to
determine the cause.
Send error. Job is
cancelled. Press
[End]. 9181
Send Email/ SMB/ FTP/ TWAIN Error: Page Max
Count Over. The number of pages of a send file
exceeds 999 pages.
"Acceptable staple
count exceeded."
Is the acceptable staple count exceeded?
"Add paper in
cassette #."
Is the indicated cassette out of paper?
"Add paper in MP
tray."
Is the paper of the specified size loaded in the
multipurpose tray?
"Add staples." Has the document finisher run out of staples?
"Add toner."
"An error has
occurred."
An internal error has occurred.Make a note of the
error code number displayed on the panel. See
above.
"Box Limit
Exceeded."
Document Box is full, and no further storage is
available; Job is cancelled. Repeat Copy Box is full,
and no further repeat copy is available.
"Cannot connect to
Authentication
Server."
"Cannot duplex
print on this
paper."
Did you select a paper size/type that cannot be
duplex printed?
"Cannot execute
this job."
Job is restricted by Job Accounting.
"Cannot offset this
paper."
Did you select a paper size that cannot be offset
(A3, B4, A5R, B6R, Folio, Ledger, Statement, &
8K)?
"Cannot punch this
paper type."
Did you select a paper size/type that cannot be
punched?
"Cannot staple this
paper."
Did you select a paper size/type that cannot be
stapled?
"Check the cover." Are any covers open? Does the message indicate
which cover is open?
"Check the
document
Is the document processor open? Is the top cover of
the document processor open?
processor."
"Check the
finisher."
Is the document finisher set correctly?"
"Clean the slit
glass."
Dirt has been identified on the slit glass.
"Empty the punch
waste box."
The punch waste box of the 3,000 sheet finisher is
full.
"Failed to specify
Job Accounting."
Job accounting is not specified in the print driver.
"Failed to store job
retention data."
"Fax box limit
exceeded."
Fax box is full, and no further storage is available.
"Finisher tray is full
of paper."
Is the acceptable storage capacity exceeded for the
document finisher tray?"
"Folding tray is full
of paper."
Is the acceptable storage capacity exceeded for the
folding tray of the 3,000 sheet document finisher?"
"Hard Disk error.
Job is cancelled.
Press [End] ##"
An error has occurred on the hard disk.
"Incorrect Login
User Name or
Password."
"Job Accounting
restriction
exceeded."
The print count exceeded the acceptable count
restricted by Job Accounting.
"Job Separator is
full of paper."
Is the maximum capacity of the job separator tray
exceeded?
"KPDL error." A PostScript error has occurred.
"Mailbox tray is full
of paper."
"Memory card
error."
Was the memory card (Compact Flash) removed
while being accessed? Was a valid memory card
inserted?
"Memory card
error. Job is
cancelled. Press
[End]. Code: 01
Memory Card Error: Format error.
"Memory card
error. Job is
cancelled. Press
[End]. Code: 04
Memory Card Error: Insufficient memory card space
to complete this operation.
"Memory is full." Unable to continue the job, as the memory is used
up."
"Memory Is Low" Logic Lockup
"Paper Jam. ###" Make a note of the jam location number displayed
on the panel. Leave the machine On.
"Print overrun." Warning. Low printer memory.
"Removable
memory error."
An error has occurred on the USB stick memory or
Compact Flash memory.
"Removable
memory was
removed."
"Replace all
originals and press
[Continue]."
"Replace the waste
toner box."
The waste toner box is full.
"Reset all originals
in the document
processor."
Are there any originals left in the document
processor?
"Scanner memory
is full."
Scanning cannot be performed due to insufficient
memory for the scanner. Is the acceptable scanning
count exceeded?
"Scanner Paused" DMA transmission of compressed, ecompressed,
rotated, relocated, or blanked-out image data does
not complete within a specified period of time.
"Set the folding
tray."
Is the folding tray correctly installed to the 3,000
sheet capacity document finisher?
"Set the folding
unit."
Is the folding tray correctly installed to the 3,000
sheet capacity document finisher?
"Set the punch
waste box."
The waste toner box is not installed correctly.
"Set the waste
toner box."
The waste toner box is not installed correctly.
"Staple error." The location of the jam will be indicated on the
panel. Leave the machine On.
"Staple jam." The location of the jam will be indicated on the
panel. Leave the machine On.
"The ID is not
registered."
The account ID# does not match.
"The memory card
is not formatted."
Is the removable memory formatted by this
machine?
"The phone
receiver is off the
hook."
"The removable
memory is not
formatted."
Is the removable memory formatted by this
machine?
"The source file is
not found."
The specified file is not found.
"Top tray of the
machine is full of
paper."
The exit tray at the top of the machine is full.
"Tray # is full of
paper."
Is the acceptable storage capacity exceeded for any
of the output trays A, B, or C of the 3,000 sheet
capacity document finisher?
"Warning low
memory."
Further scanning cannot be performed due to
insufficient memory.
Error Code Description
0xF330 Component: RIP. Category: RIP. Recovery impossible error
(CreatePrint and return back value of API is indirect).
0xF331 Component: RIP. Category: RIP. Fail to initialize.
0xF333 Component: RIP. Category: RIP. Access failure to ME.
0xF335 Component: RIP. Category: RIP. Failure to switch TASK.
0xF336 Component: RIP. Category: RIP. IOBL process failure.
0xFB30 Component: Panel. Category: KI-Panel. Failed to connect the
communication of the controller when starting up. Blue back
screen. Cannot enter maintenance mode.
0xFB31 Component: Panel. Category: KI-Panel. Refused to connect
the communication of the controller when starting up. Blue
back screen. Cannot enter maintenance mode.
0xFB32 Component: Panel. Category: KI-Panel. Time to start up
request command (start up request command could not be
received). Blue back screen. Cannot enter maintenance
mode.
0xFB33 Component: Panel. Category: KI-Panel. Cut off of the
communication with the controller is detected - waiting to
receive: select () OK return, recv() RX data length 0. Blue
back screen. Cannot enter maintenance mode.
0xFB34 Component: Panel. Category: KI-Panel. Time out for
Response telegraphic message (could not receive response
telegraphic message within a fixed time). In case on not
through httpd, this error occurs (in case it does not become
CGI time out).
0xFB35 Component: Panel. Category: KI-Panel. Received abusive
command from controller. At this moment, only the case that
unexpected command comes in when wating for the startup
request command.
0xFB36 Component: Panel. Category: KI-Panel. Connection error is
detected when waiting for he response telegraphic message
from the controller. select () function returned the error
(other than EINTR).
0xFB37 Component: Panel. Category: KI-Panel. Connection error is
detected when waiting for he response telegraphic message
from the controller. rcv () function returned the error.
0xFB38 Component: Panel. Category: KI-Panel. Communication error
is detected when transferring (using UNIX domain) response
telegraphic message in the panel. send() function returned
the error (other than EINTR).
0xFB39 Component: Panel. Category: KI-Panel. Crucial error is
detected when processing receive/transfer of the response
telegraphic message from controller. Failed to acquire
semafo???
0xFB3A Component: Panel. Category: KI-Panel. Communication error
is detected when sending required response telegraphic
message from panel. send() function returned the error
(other than EINTR).
CF000 Component: HDD. Failure to initialize with "dbinit,
hostif_stat_chg" comand.
CF000 Operation panel PWB comunication error.
CF010 ROM Checksum Error.
CF010 Main PWB Checksum Error/System Error. Communication
error between panel and main controller.
CF012 ROM Checksum Error.
CF020 Memory Checksum Error/Operation System Error.
CF030 Main PWB System Error.
CF040 Engine PWB Communication Error.
CF040 Engine PWB Communication Error.
CF041 Scanner PWB Communication Error.
CF050 Engine ROM Checksum Error.
CF060 Engine RAM Error.
CF070 Flash ROM Error. Defective flash ROM (which?).
CF080 Flash ROM Error (during download). Defective flash ROM
(which?).
CF090 Fax System M Communication Error.
CF125 Scanner Unit Error
CF131 Component: PCM. Category: OS. Failure to initialize with
"dbinit, hostif_stat_chg" comand.
CF131 Component: PCM. Category: OS. Failure to acquire Entity
data with "dbinit, hostif_stat_chg" comand.
CF145 Fax Unit Error.
CF14F Power Source Secondary Side Error/Operation System Error.
The operation decomes unstable after recovering the power
supply fail (brownout or power drop). Wall voltage is
unstable or the main power supply switch was turned
OFF/ON within 1 sec.
CF14F Component: OS. Category: OS. Primary supply voltage
dropped off temporarily and recovery operation was not
stable. If the input power supply voltage is not stable of the
Main SW is turned Off/On quickly (about 1 second), this
problem occurs.
CF186 Print Unit: DVU_PRT_SYSERR_F226_ERROR (Video data
flushing error)
CF18A Engine Firmware Incompatible.
CF18C Document BOX error.
CF1FF Component: ScanSys. Category: ScanSys. When the scanner
scanning parameter from the topside is in error.
CF1FF Component: IPLogical. Category: PrintSystem. Could not
obtain instance of Config, SystemStatus. Use below
mentioned class: ipl_search_output.cpp,
ipl_feeder_spec.cpp, outputcheck.cpp.
CF1FF Component: Machine Configuration. Category: PrintSystem.
Could not obtain instance of Config, SystemStatus. Use
below mentioned class: machine_status_engine.cpp.
CF1FF Component: OutputMission. Category: PrintSystem.
Increasing and decreasing "Lib", in case that even if there is
no original available, tried to process increasing &
decreasing.
CF1FF Component: OutputMission. Category: PrintSystem. In case
to specify some other value (indirect value) other than single
sided/duplex/forced duplex for increasing & decreasing "Lib".
CF1FF Component: OutputMission. Category: PrintSystem. In case
of the address for Job setting value structure is NULL.
CF1FF Component: OutputMission. Category: PrintSystem. In case
of the code for output completion notice is indirect.
CF1FF Component: OutputMission. Category: PrintSystem. When
writing the original information to the storage, in case to get
the reply back as [Other Error].
CF1FF Component: OutputMission. Category: PrintSystem. In case
to get the reply as [Finisher out of order Error], [No Feeder
available in search] from Paper feed/eject "Lib".
CF1FF Component: OutputMission. Category: PrintSystem. In case
to get the reply as failure from rotation calculation "Lib".
CF1FF Component: PrintSystem. Category: PrintSystem. Could not
obtain instance of Config, SystemStatus. Use below
mentioned class: print_startup.cpp.
CF1FF Component: SVI. Category: LioPanel. Logical Error (In case
of given parameter is NULL).
CF214 Codec: GICL_CDC_ERR_FACTOR_JPEG (several hardware
error, software error).
CF215 Codec: GICL_CDC_ERR_FACTOR_SRLE (several hardware
error, software error).
CF234 Data conversion error.
CF235 Error code when receiving/printing email.
CF245 Process Manager:
SYS_PRCM_ERR_FACTOR_SVC_PROC_DOWN (Device
process down).
CF246 Process Manager:
SYS_PRCM_ERR_FACTOR_DEV_PROC_DOWN (Device
process down).
CF247 Process Manager:
SYS_PRCM_ERR_FACTOR_JOBIMG_PROC_DOWN (Job image
process down).
CF247 Component: ScanSys. Category: ScanSys. Library Error
inside of ScanSys.
CF248 Component: UNKNOWN. Category: UNKNOWN.
CF248 Component: UNKNOWN. Category: UNKNOWN. Code present
on with Kyocera Barfode Font CF card installed.
CF248 Process Manager:
SYS_PRCM_ERR_FACTOR_PRN_PROC_DOWN (Printer
process down).
CF256 Fax System M IOBL error or KUIOLIB error. Poor contact at
the fax card card due to mis-installation.
CF257 Component: LFM. Category: FaxSys. KUIOLIB error. Poor
contact at the fax card card due to mis-installation.
CF257 Fax System M IOBL error or KUIOLIB error. Poor contact at
the fax card card due to mis-installation.
CF25E Network Manager:
CF25F Component: LFM. Category: FaxSys. Instance Check Error,
Paramemter Error from topside.
CF26F Component: PrintSys. Category: PrintSys. It occurs when the
error noticed from VideoDriver. Use by Video_Driver class:
Function name, factor can be found by the detail code.
CF26F Print System Other Errors. Bug of v.2.03B has been fixed by
v. 2.04A (Booklet > Booklet Print).
CF26F System State Manager:
CF278 Energy Saving Manager:
CF320 Component: LioFax. Category: FaxSys. An Observer Deletion
Error occurred during salvage process. Error received from
the method on EventManager or message Tx.
CF321 Component: LioFax. Category: FaxSys. Segment code for
LioFax initialization is different from "03KH".
CF323 Component: LioFax. Category: FaxSys. Return address of
Page class when doing FAX Tx/Rx is other abnormal error.
Entity (Config, BOX, etc.) access error.
CF324 Component: LioFax. Category: FaxSys. Entity parameter
error.
CF325 Component: LioFax. Category: FaxSys. In case that the time
when Error came back from LFM.
CF326 Component: LioFax. Category: FaxSys. IOBL error.
CF327 Component: LioFax. Category: FaxSys. At the time of
KUIOLIB error, CodeChange error, FaxLib error (Sender
recorde, Entity related error).
CF32F Component: LioFax. Category: FaxSys. Instance Check Error.
Parameter Error from topside.
CF337 Device Error (scan control):
CF3FF Component: RIP. Category: RIP. Other/System Crucial Error.
CF423 Component: FaxJOB. Category: FaxSys. As the error came
back at IF for DocumentBox, JobInfo, Config Entity.
CF423 Component: FaxJob. Category: FaxSys. The error came back
when accessing (obtaining data, setting data) to below Entity
related: job_ent(JobModel,JobInfo), config_ent, reservation,
account(certificate), document_box.
CF423 Fax System M Error. Wrong data or value detected when the
following function is used. Or poor contact at fax card due to
mis-installation.
CF423 Fax System M Error. The IF error detects during system
authentication from ACT_Account_Manager. Or poor contact
at fax card due to mis-installation.
CF424 Component: FaxJob. Category: FaxSys. As the error came
back when obtaining IF for system authentication from
ACT_Account_Manager.
CF424 Component: FaxJob. Category: FaxSys. The date obtained
from the below Entity related is unexpected data:
job_ent(JobInfo).
CF427 Component: FaxJob. Category: FaxSys. The error came back
for the IF of LioFax observer addition/deletion.
CF42F Component: FaxJob. Category: FaxSys. As handing over of
the NULL pointer in the class occurred. As memory
reservation with new in heap domain is failed: Assert for
preventing from segment drop off.
CF42F Component: FaxJob. Category: FaxSys. When generating the
class, fail new at obtaining data domain, soft logic error
(software bug).
CF433 Component: NetClient. Category: ImageProcess. Entity
Error.
CF434 Component: NetClient. Category: ImageProcess. Entity Data
Invalid.
CF437 Component: NetClient. Category: ImageProcess. Other
Library Error (ImageLibrary, PageData, EventManager).
CF43F Component: NetClient. Category: ImageProcess. Crucial (no
memory, invalid parameter, etc.).
CF441 Component: CreateScan. Category: ImageProcess. Initialize
Error.
CF444 Component: CreateScan. Category: ImageProcess. Entity
Data Invalid.
CF445 Component: CreateScan. Category: ImageProcess.
Middleware Error (LioScanner error).
CF451 Component: CreatePrint. Category: ImageProcess.
Initialization Error.
CF433
CF434
CF437
CF43F
CF441
CF444
CF445
HDD Image Process Error. Destruction of stored jobs on the
HDD. It may occur when selecting the keys for calling stored
copy or scanner job from a custom box.
CF451
CF453 Component: CreatePrint. Category: ImageProcess. Entity
Error.
CF454 Component: CreatePrint. Category: ImageProcess. Entity
Data Mismatch.
CF45F Component: CreatePrint. Category: ImageProcess. Other
Error.
CF460 Component: CreateBox (Memory Tx). Category:
ImageProcess. Unrecoverable Error.
CF463 Component: CreateBox (Memory Tx). Category:
ImageProcess. Entity Error.
CF46F Component: CreateBox (Memory Tx). Category:
ImageProcess. Crucial (no memory, invalid parameter, etc.).
CF46F PDL Interpreter: REN_INT_ERR_FACTOR_GENERAL (other
general error).
CF470 Component: CreateFax. Category: ImageProcess.
Unrecoverable Error.
CF473 Component: CreateFax. Category: ImageProcess. Entity
Error.
CF47F Component: CreateFax. Category: ImageProcess. Crucial (no
memory, invalid parameter, etc.).
CF484 Component: Edit. Category: ImageProcess. Data Invalid
(PageData).
CF487 Component: Edit. Category: ImageProcess. Other Library
Error (ImageLibrary).
CF48F Component: Edit. Category: ImageProcess. Crucial.
CF490 Component: Output(Fax). Category: ImageProcess.
Unrecoverable Error.
CF493 Component: Output(Fax). Category: ImageProcess. Entity
Error.
CF494 Component: Output(Fax). Category: ImageProcess. Entity
Data Invalid.
CF45F
CF453
CF454
CF45F
CF460
CF463
CF46F
CF470
CF473
CF47F
CF484
CF487
CF48F
CF490
CF493
CF494
HDD Image Process Error. Destruction of stored jobs on the
HDD. It may occur when selecting the keys for calling stored
copy or scanner job from a custom box.
CF515
CF526 System Error:
CF528 Component: SVI. Category: LioPanel. Panel data abusion
error.
CF530 Component: PJL. Category: RIP. Recovery impossible error:
Thread Create failed.
CF530 Component: ReportEventService. Category: RIP. Recovery
impossible error: Thread Create failed.
CF530 Component: SVCTL_FaxRx_Event_Control. Category: KI Sc.
As failed to obtain EM_FaxRx_Ec_Event_Fax_Enable.
CF530 Component: SVCTL_Reservation_Event_Control. Category:
KI Sc. As failed to notice the event for
EM_Rsv_EC_op_Event_FaxJob_Ready.
CF530 Component: SVCTL_Job_Start_Command. As JobInfo giving
to JSM_JobServiceManager is NULL.
CF533 Component: PJL. Category: RIP. Entity error: when CLITICAL
ERROR occurred at ME access.
CF533 Component: ReportEventService. Category: RIP. Entity
error: when CLITICAL ERROR occurred at ME access.
CF551 Component: MLPRN. Category: NetAppl. Task generation
error.
CF551 Component: MLPRT. Category: NetAppl. Task generation
error.
CF551 Component: EVR_LGS. Category: NetAppl. Task generation
error.
CF610 Component: SSTUP. Category: OS. Error in the
SystemStartUp (Thread generation, Entity data acquisition,
DiskManager operation).
CF610 Undefined.
CF610 System Start Error.
CF615 Report Page Generator: USV_RPG_ERR_FACTOR_STREAM
(Stream access error).
CF620 Component: EventManager. Category: KM-Entity. Failed to
obtain/receive event from framework.
CF620 Unable to Print.
CF620 System Error. Error acquiring the event data. Panel detects
CF000 as same error.
CF620 System Error. Error acquiring the event data. Panel detects
CF000 as same error. Unable to Load Files To CF Card.
CF630 Component: PowerManagement. Category: OS. Failed to
mount or unmount during transition of the condition.
CF710 Component: IIS. Category: NetApl. Network file written error
(inetd).
CF713 Component: IIS. Category: NetApl. Entity error (inetd).
CF720 Component: IIS. Category: NetApl. Network file written error
(services).
CF723 Component: IIS. Category: NetApl. Entity error (services).
CF730 Component: IIS. Category: NetApl. Network file written error
(snmpd).
CF733 Component: IIS. Category: NetApl. Entity error (snmpd).
CF743 Component: IIS. Category: NetApl. Entity error (hosts
allow).
CF750 Component: IIS. Category: NetApl. Network file written error
(hostname).
CF753 Component: IIS. Category: NetApl. Entity error (hostname).
CF760 Component: IIS. Category: NetApl. Network file written error
(papd).
CF763 Component: IIS. Category: NetApl. Entity error (papd).
CF770 Component: IIS. Category: NetApl. Network file written error
(cups).
CF773 Component: IIS. Category: NetApl. Entity error (cups).
CF780 Component: IIS. Category: NetApl. Network file written error
(dhcclient).
CF783 Component: IIS. Category: NetApl. Entity error (dhcclient).
CF790 Component: IIS. Category: NetApl. Network file written error
(smb).
CF793 Component: IIS. Category: NetApl. Entity error (smb).
CF7A0 Component: IIS. Category: NetApl. Network file written error
(netware).
CF7A3 Component: IIS. Category: NetApl. Entity error (netware).
CF7B0 Component: IIS. Category: NetApl. Network file written error
(ipfilter).
CF7B3 Component: IIS. Category: NetApl. Entity error (ipfilter).
CF7C0 Component: IIS. Category: NetApl. Network file written error
(ethermode).
CF7C3 Component: IIS. Category: NetApl. Entity error (ethermode).
CF7D0 Component: IIS. Category: NetApl. Network file written error
(other).
CF7D3 Component: IIS. Category: NetApl. Entity error (other).
CF7D7 Readout Error of SSL (authentication data).
CFAxx HDD Error.
CFAxx HDD Error.
CFA10 Component: OS_TOOLS. Category: OS. Error inside of hot
plug detection thread, overwritten thread (failed to issue the
event, failed to operate signal handler).
CFA20 Component: OS_TOOLS. Category: OS. Failed to obtain
memory size.
CFA23 Component: OS_TOOLS. Category: OS. Access error to the
Entity at master data stored area component.
CFA30 Component: OS_TOOLS. Category: OS. CF-DETECT OPEN
error <0x07>.
CFA30 Component: OS_TOOLS. Category: OS. CF-DETECT IOCTL
error <0x08>.
CFA30 Component: OS_TOOLS. Category: OS. CF-DETECT CLOSE
error <0x09>.
CFA30 Component: OS_TOOLS. Category: OS. AES conversion
OPEN error <0x0a>.
CFA30 Component: OS_TOOLS. Category: OS. AES conversion
IOCTL error <0x0b>.
CFA30 Component: OS_TOOLS. Category: OS. AES conversion
CLOSE error <0x0c>.
CFA30 Component: OS_TOOLS. Category: OS. AES conversion
command return value error <0x0d>.
CFA30 Component: OS_TOOLS. Category: OS. Message queue
creation error <0x15>.
CFA30 Component: OS_TOOLS. Category: OS. Message queue Tx
error <0x16>.
CFA30 Component: OS_TOOLS. Category: OS. Message queue Rx
error <0x17>.
CFA30 Component: OS_TOOLS. Category: OS. Message queue
deletion error <0x18>.
CFA37 Component: OS_TOOLS. Category: OS. Event Tx error
<0x19>.
CFA43 Component: OS_TOOLS. Category: OS. Access error to the
Entity at USB activation component.
CFB00 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_E_GENERIC).
CFB01 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_DNS_INVAL).
CFB02 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_DNS_NOSERVER).
CFB03 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_DNS_TIMEDOUT).
CFB04 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_DNS_NOTFOUND).
CFB05 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_TCP_OPEN).
CFB06 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_TCP_CONNECT).
CFB07 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_TCP_READ).
CFB08 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_TCP_WRITE).
CFB09 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_SSL_CONNECT).
CFB0A Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_SSL_HANDSHAKE).
CFB0B Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_SSL_READ).
CFB0C Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_SSL_WRITE).
CFB0D Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_REQTIMEDOUT).
CFB0E Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_RSPTIMEDOUT).
CFB0F Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_CACHE_NONE).
CFB10 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_CACHE_EXPIRE).
CFB11 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_AUTH_UNKNOWN).
CFB12 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_AUTH_NOHEADER).
CFB13 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_AUTH_FORMAT).
CFB14 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_REDIRECT_FORMAT).
CFB15 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_REDIRECT_CANCELLED).
CFB16 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_REQ_HEADER_SIZEOVER).
CFB17 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_REQ_BODY_SIZEOVER).
CFB18 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_RSP_HEADER_SIZEOVER).
CFB19 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_REQ_TOOMANYCONTINUE).
CFB1A Component: Panel. Category: KI-Panel. Netfront error
(SLIM_HTTP_E_TLS_INTOLERANT).
CFB1B Component: Panel. Category: KI-Panel. Netfront error
(SLIM_FILEP_E_OPEN).
CFB1C Component: Panel. Category: KI-Panel. Netfront error
(SLIM_FILEP_E_READ).
CFB1D Component: Panel. Category: KI-Panel. Netfront error
(SLIM_CONTENT_E_SIZEOVER).
CFB1E Component: Panel. Category: KI-Panel. Netfront error
(SLIM_CONTENT_E_NO_CONTENT).
CFB1F Component: Panel. Category: KI-Panel. Netfront error
(SLIM_CONTENT_E_TOOMANYREDIRECT).
CFB20 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_CONTENT_E_TOOMANYAUTH).
CFB21 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_BROWSER_ERROR_NOMEMORY).
CFB22 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_BROWSER_ERROR_NOMEMORY_IMAGE).
CFB23 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_BROWSER_ERROR_TOTAL_SIZEOVER).
CFB24 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_BROWSER_ERROR_BADURL).
CFB25 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_BROWSER_ERROR_BADMIMETYPE).
CFB26 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_BROWSER_ERROR_MIXEDSECURETYPE).
CFB27 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_BROWSER_ERROR_INPUTHISTORY_SIZEOVER).
CFB28 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_BROWSER_ERROR_INPUT_REQUIRED).
CFB29 Component: Panel. Category: KI-Panel. Netfront error
(SLIM_BROWSER_ERROR_KMC_NOTIFYMAXWINDOW).
CFB2A Component: Panel. Category: KI-Panel. Netfront error
(SLIM_BROWSER_ERROR_KMC_SWKOVERFLOW).
CFB2B Component: Panel. Category: KI-Panel. Netfront error
(SLIM_BROWSER_ERROR_KMC_FILEDOWNLOAD).
CFB2C Component: Panel. Category: KI-Panel. Netfront error
(SLIM_BROWSER_ERROR_KMC_SEGFAULT).
CFB2C
CFB30
CFB31
Panel Error. NetFont error. Communication error between
panel and main controller during initialization or rejection of
communication by controller during initialization. Blue Screen
of Death.
CFB30 Component: Panel. Category: KI-Panel. Failed to connect the
communication of the controller when starting up. Blue back
screen. Cannot enter maintenance mode.
CFB30 Incompatible Level Of Firmware on Main EEPROM.
CFB30 Incompatible Level Of Firmware on Main EEPROM.
CFB31 Component: Panel. Category: KI-Panel. Refused to connect
the communication of the controller when starting up. Blue
back screen. Cannot enter maintenance mode.
CFB31 Corrupt Firmware on Main EEPROM.
CFB31 Corrupt Firmware on Main EEPROM.
CFB32 Component: Panel. Category: KI-Panel. Time to start up
request command (start up request command could not be
received). Blue back screen. Cannot enter maintenance
mode.
CFB32 Panel Error. Timeout request for start up command. Start
command hasn't been received. Possible destruction of
system file in HDD. Cannot enter maintenance mode. Blue
Screen of Death.
CFB33 Component: Panel. Category: KI-Panel. Cut off of the
communication with the controller is detected - waiting to
receive: select () OK return, recv() RX data length 0. Blue
back screen. Cannot enter maintenance mode.
CFB33 Panel Error. Detects disconnection with controller. Possible
overdrive of control board or destruction of system file in
HDD. Cannot enter maintenance mode. Blue Screen of
Death.
CFB34 Component: Panel. Category: KI-Panel. Time out for
Response telegraphic message (could not receive response
telegraphic message within a fixed time). In case on not
through httpd, this error occurs (in case it does not become
CGI time out).
CFB35 Component: Panel. Category: KI-Panel. Received abusive
command from controller. At this moment, only the case that
unexpected command comes in when wating for the startup
request command.
CFB36 Component: Panel. Category: KI-Panel. Connection error is
detected when waiting for he response telegraphic message
from the controller. select () function returned the error
(other than EINTR).
CFB37 Component: Panel. Category: KI-Panel. Connection error is
detected when waiting for he response telegraphic message
from the controller. rcv () function returned the error.
CFB38 Component: Panel. Category: KI-Panel. Communication error
is detected when transferring (using UNIX domain) response
telegraphic message in the panel. send() function returned
the error (other than EINTR).
CFB39 Component: Panel. Category: KI-Panel. Crucial error is
detected when processing receive/transfer of the response
telegraphic message from controller. Failed to acquire
semafo???
CFB3A Component: Panel. Category: KI-Panel. Communication error
is detected when sending required response telegraphic
message from panel. send() function returned the error
(other than EINTR).