CANINE RESPITE AREA
Transcript of CANINE RESPITE AREA
CH
ILD
RE
N'S
HO
SP
ITA
L C
OL
OR
AD
O
CA
NIN
E R
ES
PIT
E A
RE
A
SHEET NUMBER
DATE ISSUED:
SCALE:
10/14/2020
REVISIONS:
No. DATE DESCRIPTION
DESIGNED BY:DRAWN BY:CHECKED BY:
SEAL:
BY
11-03-20 DD SUBMITTAL
SHEET TITLE
LS-001
GENERAL NOTES
1. All work shall be performed in accordance with plans approved by the University of Colorado AnschutzMedical Campus.
2. Base information provided by Civil Engineer. Refer to survey, plat, roadway and utility drawings, and otheravailable documents for property limits, existing conditions, and horizontal and vertical control.
3. The limits of work occur at the right-of-way or as shown on plans.4. Verify existing site conditions including, walls, vegetation fences, utilities, property lines, limits of roadways,
curbs and gutters, and other obstructions that may affect the progress of work.5. Locate utilities and maintain their location during all phases of work. Do not damage utility lines/structures.
Notify Owner's Representative of any discrepancies before starting any work. Contractor shall be responsiblefor location of underground utilities or structures, whether or not shown or detailed and installed by any othercontract. Restoration of utilities damaged by the Contractor shall be at the Contractor's expense.
6. Thoroughly review the site conditions, drawings, and technical specifications prior to construction. Completethe work of this project in accordance with approved drawings.
7. Anything mentioned in the technical specifications and not shown on the drawings, or shown on thedrawings and not mentioned in the technical specifications shall be of like effect as if shown on or mentionedin both.
8. Construction installation, materials, testing and inspection shall comply with applicable codes andordinances.
9. Take necessary steps to protect and maintain all finished work for the duration of the contract until finalacceptance
10. These drawings do not specify safety materials, equipment, methods or sequencing to protect persons andproperty. Direct and implement safety operations and procedures to protect the Owner, other Contractors,the Public, and others for the duration of the contract.
11. Notes and details on specific drawings take precedence over general notes and typical details.12. Obtain necessary permits from all jurisdictions as required to construct the work of this project.13. The work of this contract will not be considered complete until all areas have been cleaned of all dirt and
debris and all damaged items are repaired.14. Irrigation system to be designed. It is anticipated that irrigation system will be a modification of the existing
system. Lawn areas to have pop up heads. Shrub areas to have subsurface irrigation (netafim or similar.)
GRADING NOTES1. Employ a licensed surveyor to establish all grade and work lines. Have Owners Representative review grade
stakes prior to final grading.2. All proposed grades shall meet and blend with existing grades at project limits and at curbs sidewalks and
roadways. Existing elevations indicated on plans shall be verified in field to as-built condition.3. Erosion Control- See Civil Engineering Drawings for Contractor responsibilities, means, and methods.4. Contractor shall be responsible for 'rounding off' all sharp ridges existing on site whether or not such conditions
are indicated on plans. Round tops and toes of slope to provide smooth transition to existing grade. Bermsand landforms will be smooth and rounded vertical curves with no sharp transition in grade, unless otherwisenoted.
5. Contractor shall not proceed with construction when it becomes evident that unforseen obstructions, areadiscrepancies and/or grade differences exist. Such conditions shall be immediately brought to the attention ofthe Owner's Representative for decision. The Contractor shall assume full responsibility for all necessaryrevisions due to failure to give such notification.
6. All landscape grades are based upon elevations shown on the Civil Engineer drawings.7. Contractor shall be responsible for any coordination with subcontractors as required to accomplish all grading
operations.8. Maintain positive drainage, unless specifically designed for ponding, at all times. Minimum 2% slope in planted
areas, Minimum 1% in paved areas. Refer to Civil Engineer's drawings for drainage structure locations anddetails..
9. Hold finish grades of shrub and ground cover areas 1" below the top of adjacent pavements or curbs, unlessotherwise noted.
10. Subsurface drainage lines shall be placed with a minimum of 12" cover. Contractor is responsible for verifyinginvert elevations at all drains and pipe depths to ensure positive drainage at the slope indicated to the outletshown on the plans.
11. Maximum slope in landscape planting areas is 3:1. Max slope in turf/sod areas is 4:1.12. No change in contract price will be allowed for actual or claimed discrepancy between existing grade and those
shown on plans after Contractor has accepted existing grades and moved onto site13. Maximum running slopes along walkways are designed and drawn at 4.8% slope in order to ensure the finished
slope is below 5% per ADA guidelines. No running slopes in the direction of travel on paved surfaces are to begreater than 5% without a handrail.
14. Maximum cross slope on walkways are designed and drawn at 1.8% slope in order to ensure the finished crossslope is less than 2% per ADA guidelines. No cross slopes on paved surfaces are to be greater than 2%.
LAYOUT NOTES1. Verify existing site information including, but not limited to street grades, utilities, property
lines, limits of roadways, curbs and gutters taken from the Civil Engineer's drawings.2. All work shall comply with applicable codes and ordinances.3. Take all dimensions from back of curb, face of wall or building, and centerline of trees unless
otherwise noted.4. All dimensions called out as 'equal' are equidistant measurements.5. Written dimensions supercede scaled dimensions. Do not scale drawings, if there is a
question regarding dimensions, contact Dig Studio for verification.6. All angles to match those noted on drawing and all lines of paving to be parallel unless
otherwise noted. Maintain horizontal alignment of adjacent elements as noted on drawings.7. Reference to north refers to true north. Reference to scale is for full sized drawings only. Do
not scale from drawings.8. Concrete slabs or footings shall be doweled into abutting walls, foundations and footings
only where shown on the plans and details.9. Provide expansion joints in concrete paving a maximum distance of 50 feet apart and at all
intersections, where new concrete abuts existing concrete paving, buildings, curbs andwalls unless otherwise noted.
10. Provide control joints evenly spaced between expansion joints as shown on drawings,except where special score joint pattern is specified.
11. Sleeves and conduits shall be installed a minimum of 18 inches below finished grade andshall extend 12 inches beyond back of curbs, walls, and paving.
12. Coordinate and field verify all sleeving locations for all utility, electrical, and irrigation prior toconstruction.
1. All plant materials shall meet or exceed current American Standard forNursery Stock (ANSI Z60.1-2004) and the Colorado Nursery Act andaccompanying Rules and Regulations.
2. All plants will be balled and burlapped or container grown. Bare root orspaded plants will not be accepted.
3. Supply all plant material in quantities sufficient to complete the plantingbed as shown on the drawings.
4. All plants will be inspected and approved by the Owner's Representativeprior to delivery to the site.
5. Any proposed substitutions of plant species shall be approved by theLandscape Architect and University representative prior to delivery to thesite.
6. Obtain Landscape Architects approval of finish grading prior to the startof planting.
7. Stake locations of all proposed trees and edges of new planting beds forapproval by the Landscape Architect prior to the commencement ofplanting.
8. Landscape Contractor shall be responsible for becoming aware of allunderground utilities, pipes and structures. The Landscape Contractorshall be held responsible for contacting all utility companies for fieldlocation of underground utility lines prior to any excavation. LandscapeContractor shall take sole responsibility for any cost of utility repair due todamage caused by his operations.
9. Do not willfully proceed with construction as designed when it is obviousthat unknown obstructions and/or grade differences exist that may nothave been known during design. Such conditions shall be immediatelybrought to the attention of the Landscape Architect. The LandscapeContractor shall assume full responsibility for all necessary revisions dueto failure to give such notification.
10. Landscape Contractor shall be responsible for any coordination withsubcontractors as required to accomplish planting operations.
11. See specifications for planting requirements, soil preparation testing,materials and execution. Arrange for visit of Landscape Architect forreview and approval a minimum of 48 hours prior to installation.
12. See details and specifications for staking method, plant pit dimensionsand backfill requirements.
13. Landscape Contractor shall provide per-unit costs for every size of plantmaterials, and by type, as called out on planting plans. Unit cost toinclude the plant material itself and installation, including all labor,amendments, fertilizers, etc., as detailed and specified for each size.
14. Landscape Contractor is responsible to do their own quantity takeoffs forall plant materials and sizes shown on plans.
PLANTING NOTES15. The Landscape Contractor shall be responsible for positive drainage
throughout the site with accurately set flow lines. No low spots or ponding ofsurface water will be accepted in final work.
16. Coordinate installation of large plant material with installation of wall footings,bridge abutments and pavements. Any damage to improvements by othersis the responsibility of the Landscape Contractor.
17. The Landscape Contractor shall allow for the addition of specified quantitiesof soil amendments, conditioners and mulch in soil preparation and finishgrading.
18. Imported soil shall be used to supplement the existing soil as necessary tomeet the finish grade requirements at planting areas.
19. The Landscape Contractor shall verify soil test at his expense prior toplanting and will follow test recommendations and Landscape Architect'sapproval for soil amendments.
20. The Landscape Contractor shall receive the specified subgrade elevation, of+/- one tenth of a foot below finish grade. The Landscape Contractor shallbe responsible to furnish and install amended or imported soil in any plantingareas as necessary to achieve the specified finish planting grades unlessotherwise noted on plans or specs.
21. Contractor is to familiarize himself with the layout, grading and civilengineering documents to coordinate actual location of trees and shrubs.
22. Maintenance Statement:All landscaping shown on this plan shall be maintained in a neat and adequate manner. Required maintenance activities shall include, but not limited to, mowing of lawns, trimming of hedges, adequate irrigation, replacement of dead, diseased or unsightly landscaping, removal of weedsfrom planted areas, and appropriate pruning of plant materials.
23. Take all dimensions from back of curb, center line of trees, and centerline oflight pole bases, unless otherwise noted.
24. Take all dimensions perpendicular to any reference line, centerline, buildingface, or back of curb.
25. Written dimensions supercede scaled dimensions. Do not scale drawings, ifthere is a question regarding dimension, contact Landscape Architect forverification.
GENERAL NOTES
SHEET INDEX
Sheet Number Sheet Title
LS-001 GENERAL NOTES
LM-101 MATERIALS PLAN
LS-101 LAYOUT PLAN
LS-201 SITE ENLARGEMENT
LS-202 SITE ENLARGEMENT
LS-203 SITE ENLARGEMENT
LS-501 SITE DETAILS
LS-502 SITE DETAILS
LS-503 SITE DETAILS
LP-101 PLANTING PLAN
LP-102 PLANT PALETTE
LP-501 PLANTING DETAILS
BUILDING
R12'-6"
R3'
R6'
BUILDING
EXISTING LIGHT
EXISTING LIGHT
IRRIGATIONBOXES, TYP.
EXISTING SHRUBS, TYP.
TURF SOD TOREPLACE ASNECESSARY
EXISTING TREE
EXISTING DRAIN
ARTIFICIAL TURF
EXISTING STONES, TYP.
EXISTING WALKWAY
EXISTING WALKWAY
EXISTING WALKWAY
R3'
6'
38'-3"
3-01
1LS-203
2LS
-203
3-02
1-13
3-05
2-07
5-08 LINK BENCH B
5-08LINK BENCH A 1-11 1-12
SEE 1/LS-202 FORENLARGEMENT
SEE 2/LS-201 FORENLARGEMENT
SEE 1/LS-201 FORENLARGEMENT
5-09
1-10
1-10
5-10
1-06
8-01
8-02
NORTH
0 5' 10' 20'
SCALE: 1" = 10'-0"
CH
ILD
RE
N'S
HO
SP
ITA
L C
OL
OR
AD
O
CA
NIN
E R
ES
PIT
E A
RE
A
SHEET NUMBER
DATE ISSUED:
SCALE:
10/14/2020
REVISIONS:
No. DATE DESCRIPTION
DESIGNED BY:DRAWN BY:CHECKED BY:
SEAL:
BY
11-03-20 DD SUBMITTAL
SHEET TITLE
1" = 10'
1 - PAVING & SURFACING: DIVISION 32SYMBOL DESCRIPTION DETAIL
SYNLAWN PET SYSTEM 1/LS-502
DG AND FENCE 5/LS-502
MAIN MOUND 1/LS-200
CRESECENT MOUND 2/LS-200
DOG PAW MOUND 1/LS-201
2 - WALLS & FENCES: DIVISION 32SYMBOL DESCRIPTION DETAIL
AMERISTAR WIREWORKS PLUS FENCE 2/LS-502
3 - METALS: DIVISION 05SYMBOL DESCRIPTION DETAIL
ENTRY FEATURE 1/LS-500
DOG PAW "TOE" PLATFORM 2/LS-500
SHADE STRUCTURE 4/LS-501
5 - FURNISHINGS: DIVISION 32SYMBOL DESCRIPTION DETAIL
LINK BENCH 3/LS-502
NEOLIVIANO BENCH 4/LS-502
WAYFINDING SIGN 6/LS-502
8 - PLANTING: DIVISION 32SYMBOL DESCRIPTION DETAIL
TREE PLANTING
SHRUB PLANTING
1-06
1-10
1-11
1-12
1-13
2-07
3-01
3-02
3-05
5-08
5-09
5-10
8-01
8-02
REFERENCE NOTES SCHEDULE
LM-101
MATERIALS PLAN
7'
BUILDING
6'
BUILDING
1'
BREAKPOINT OF RADII
4'
1'
4'
4'
4'1'
1'
1'
1'
SEE 1/LS-202 FORENLARGEMENT
SEE 2/LS-201 FORENLARGEMENT
SEE 1/LS-201 FORENLARGEMENT
39'-1
"
95'
1'-3"
9'-6
"
4'1'
R15
'
R12'-8"
R14'
R27
'
R28'
R7'
-6"
R2'
11'-6"
R28'
R17
'
15'
1'1'
-11"
7'-8"
22'-1
"
15'-9"
4'-3
"
37'-7
"
18'
R28'
R36'
31'-6
"
32'-4
"
39'-4
"
20'-2
"
39'-6
"48'
41'-1
1"2'-7"11'-9"
10"13'7'-2"8'-6"16'-5"5'-7"
3'-10"26'-8"
2'-6"
50'-9
"
3'3'-3"
NORTH
0 5' 10' 20'
SCALE: 1" = 10'-0"
CH
ILD
RE
N'S
HO
SP
ITA
L C
OL
OR
AD
O
CA
NIN
E R
ES
PIT
E A
RE
A
SHEET NUMBER
DATE ISSUED:
SCALE:
10/14/2020
REVISIONS:
No. DATE DESCRIPTION
DESIGNED BY:DRAWN BY:CHECKED BY:
SEAL:
BY
11-03-20 DD SUBMITTAL
SHEET TITLE
1" = 10'
LS-101
LAYOUT PLAN
R3'
R6'
R3'
6'
38'-3"
2LS-201
R12'-6"
1LS-201
NORTH
CH
ILD
RE
N'S
HO
SP
ITA
L C
OL
OR
AD
O
CA
NIN
E R
ES
PIT
E A
RE
A
SHEET NUMBER
DATE ISSUED:
SCALE:
10/14/2020
REVISIONS:
No. DATE DESCRIPTION
DESIGNED BY:DRAWN BY:CHECKED BY:
SEAL:
BY
11-03-20 DD SUBMITTAL
SHEET TITLE
2
ENLARGEMENT - CRESCENT MOUND
1/4" = 1'
1
ENLARGEMENT - MAIN MOUND
1/4" = 1'
CRESCENT MOUND, 3.5' HT.,SEE DETAIL AND SECTION
SHADE STRUCTURE,SEE DETAIL
LINK BENCH B, SEE DETAIL
MOUND, 5' HT., SEE DETAIL AND SECTION
EXISTING DRAIN
2'
SYNLAWN PET SYSTEM ARTIFICIALTURF, SEE DETAIL 1/L502 FORINSTALLATION SPECIFICATIONS
COMPACTEDSOIL, 8" LIFTS
5'
2'
6" 11'-6" 11'-6" 6"
R3'-6" R
3'-6
"R3'-6"
℄
4" COMPACTED CLASS 4ROAD BASE CAP
1
℄
R1'-3" R1
'-3"
R1'
2'7"
6" 3' 3' 6"
2'-8
"
SYNLAWN PET SYSTEM ARTIFICIALTURF, SEE DETAIL 1/L502 FORINSTALLATION SPECIFICATIONS
COMPACTEDSOIL, 8" LIFTS
4" COMPACTED CLASS 4ROAD BASE CAP
2
PLAN
SECTION
PLAN
24" DIA. DRAIN PIPE, CUTANGLE TO MATCH SLOPE
1/2" = 1'0"
SECTION
1/2" = 1'0"
NOTE: FINAL SHAPING OF ALLMOUNDS TO BE APPROVED IN THEFIELD BY LANDSCAPE ARCHITECTBEFORE AGGREGATE BASE CAP ANDSYNLAWN ARE INSTALLED
NOTE: FINAL SHAPING OF ALLMOUNDS TO BE APPROVED IN THEFIELD BY LANDSCAPE ARCHITECTBEFORE AGGREGATE BASE CAP ANDSYNLAWN ARE INSTALLED
LS-201
SITE ENLARGEMENT
41°41°
41°
8'-9"
R2'
R2'
R2'
R7'
R7'
R3'
1LS-201
NORTH
1
ENLARGEMENT - DOG PAW MOUND
1/4" = 1'
CH
ILD
RE
N'S
HO
SP
ITA
L C
OL
OR
AD
O
CA
NIN
E R
ES
PIT
E A
RE
A
SHEET NUMBER
DATE ISSUED:
SCALE:
10/14/2020
REVISIONS:
No. DATE DESCRIPTION
DESIGNED BY:DRAWN BY:CHECKED BY:
SEAL:
BY
11-03-20 DD SUBMITTAL
SHEET TITLE
PAW-SHAPED MOUND, 3' HT., SEE DETAIL
RAISED PLAY PLATFORMS, HT. VARIES, SEE DETAIL
1'
6" 6"4'-6" 4'-6"
R1'-8" R
1'-8
"R2'
1'
℄
3'
SYNLAWN PET SYSTEM ARTIFICIALTURF, SEE DETAIL 1/L502 FORINSTALLATION SPECIFICATIONS
COMPACTEDSOIL, 8" LIFTS
4" COMPACTED CLASS4 ROAD BASE CAP
1
SECTION
1/2" = 1'0"
NOTE: FINAL SHAPING OF ALLMOUNDS TO BE APPROVED IN THEFIELD BY LANDSCAPE ARCHITECTBEFORE AGGREGATE BASE CAP ANDSYNLAWN ARE INSTALLED
LS-202
SITE ENLARGEMENT
1
ILLUSTRATIVE SECTION ELEVATION A
1" = 10'-0"
CH
ILD
RE
N'S
HO
SP
ITA
L C
OL
OR
AD
O
CA
NIN
E R
ES
PIT
E A
RE
A
SHEET NUMBER
DATE ISSUED:
SCALE:
10/14/2020
REVISIONS:
No. DATE DESCRIPTION
DESIGNED BY:DRAWN BY:CHECKED BY:
SEAL:
BY
11-03-20 DD SUBMITTAL
SHEET TITLE
2
ILLUSTRATIVE SECTION ELEVATION B
1" = 10'-0" LS-203
SITE SECTIONS
CH
ILD
RE
N'S
HO
SP
ITA
L C
OL
OR
AD
O
CA
NIN
E R
ES
PIT
E A
RE
A
SHEET NUMBER
DATE ISSUED:
SCALE:
10/14/2020
REVISIONS:
No. DATE DESCRIPTION
DESIGNED BY:DRAWN BY:CHECKED BY:
SEAL:
BY
11-03-20 DD SUBMITTAL
SHEET TITLE
11'
5'4'
2'
5" 5"
4'-3"
10"
1'-4
" 8"8"
5" 5"
R1'R1'
2'-8"
6"
5" DIA. CENTER CROSS TUBE
1'-9"1'-9"
5" DIA. TUBE RING, TENEMICPAINT CHILDREN'S HOSPITALYELLOW
DONOR SIGN ORCANINE RESPITEAREA SIGN
5" DIA. METAL TUBE
TUF GRID FENCE
BASE PLATE CONNECTIONTO BELOW SYN LAWN
NOTE: CONTRACTOR TO PROVIDESTRUCTURAL ENGINEERING FOR ENTRYPORTAL STRUCTURE AND SHOPDRAWINGS FOR REVIEW
J-BOLT ANCHOR INTOCONCRETE FOOTING
CONCRETE BASE
5"
ENTRY PORTAL FEATURE1/2" = 1'-0"
10"
3"
3" DIA. CROSSBAR, TENEMICPAINT CHILDREN'S HOSPITALYELLOW
3'3'
3'
4'4'
2'
3'
2'
4'
3"
FENCE POST, 3"X3"CONCRETE BAND,SEE DETAIL
BUILDING FACE
FENCE ENDS ATBUILDING CORNER
5"1'
-41 2"
5"
1'-4
1 2"
6'-7
"
R5'-6"
GATE, 3' WIDTH
GATE, 3' WIDTH
AMERISTARWIREWORKS PLUSFENCE, 5' HT, SEEDETAIL
10'-7"
5" DIA. TUBE RING, TENEMICPAINT CHILDREN'S HOSPITALYELLOW
3" DIA. CROSSBAR,TENEMIC PAINTCHILDREN'SHOSPITAL YELLOW
5" DIA. TUBE RING,TENEMIC PAINTCHILDREN'SHOSPITAL YELLOW
10'-5
1 2"
2'-6"
6"
2'-6"
R5"
7'
2"
SECTION PLAN ISOMETRIC
1
DOG BAG DISPENSER3/4" = 1'-0"
4'1'
-6" M
IN3'
1'
POST CAP
GALVANIZED VANDALRESISTANT MOUNTINGHARDWARE
DOG BAG DISPENSER AND BAGS,RE: SPECS.2 1/2" SQUARE GALVANIZEDSTEEL POST
TROWEL FINISHTOP OF FOOTING
FINISHED GRADE, FLUSHWITH TOP OF FOOTING
CONDITION VARIES,REF PLAN
CONCRETEFOOTING
COMPACT SUBGRADETO 95% SPD
3
4'-6"
3'-6"
R3"
1'-9"
4'-6"
1"
6"HEIGHT VARIESBETWEEN 1' AND 2'3";SEE PLAN FOR DETAILS
2'
METAL PLATFORM; COLORSVARY BETWEEN CHCO YELLOW,RED, BLUE AND ORANGE
6" DIA. STEEL POSTMETAL PLATFORM; COLORSVARY BETWEEN CHCOYELLOW, RED, BLUE ANDORANGE
CIP CONCRETE FOOTERCOMPACT SUBGRADE TO95% SPD
SYNLAWN PET SYSTEM ARTIFICIALTURF, SEE DETAIL FORINSTALLATION SPECIFICATIONS
DOG PAW "TOE" PLATFORM1/2" = 1'-0"
CUT ARTIFICIAL TURFTO COVER BASE PLATE
3'
1'
2 LITTER RECEPTACLE1" = 1'-0"
NOTES:1. INSTALL PER MANUFACTURERS RECOMMENDATIONS.
MANUFACTURER: DUMOR
SIZE: 22 GAL.
MODELS: TRASH: #287-32 SH SO W/ SHIELDS
RECYCLE: #287-32 SH RC2 W/ SHIELDS MIXED RECYCLING
COLOR / MATERIAL: BLACK / STEEL
SURFACE MOUNT
4
LS-501
SITE DETAILS
CH
ILD
RE
N'S
HO
SP
ITA
L C
OL
OR
AD
O
CA
NIN
E R
ES
PIT
E A
RE
A
SHEET NUMBER
DATE ISSUED:
SCALE:
10/14/2020
REVISIONS:
No. DATE DESCRIPTION
DESIGNED BY:DRAWN BY:CHECKED BY:
SEAL:
BY
11-03-20 DD SUBMITTAL
SHEET TITLE
SHADE STRUCTURE 1/2" = 1'-0"
(3) 5" DIA.COMBINEDCENTER POSTS
12'X
7'-2
"
10'-6
"X
3" DIA. ROUNDSUPPORT BEAMS
120°
120°
120°
1'-8"
3'-1
0"
120°
120°
120°
1'-8"9"
1'-11"
10-GAGE ALUMINUMPANELS, 1/8TH INCHROUND HOLES ON 14"STAGGERED CENTERS
1/8TH INCH GAPBETWEEN PANELS
40°
TOP VIEW STRUCTURE PLAN TOP VIEW SHADE PANEL PLAN
1'-6"
12'
1'-8" 3'-10"9" 1'-8" 9"1'-8" 1'-8"5"
3"
5"
1"1"
3"
1"
R1'-6
" R1'-6"
10'
3'
4'
MESH METAL BENCH RING
(3) 5" DIA. TUBE COLUMNS
3" DIA. METAL TUBE RINGS
5" DIA. METAL TUBE
INFILL ALUMINUMPERFORATED SECTIONS 1/8THINCH ROUND HOLES ON 14 INCHSTAGGERED CENTERS
NOTE: CONTRACTOR TOPROVIDE STRUCTURALENGINEERING FOR ENTRYPORTAL STRUCTURE AND SHOPDRAWINGS FOR REVIEW
CONCRETE FOUNDATION 3' DIA.AND 4' DEEP, WITH #6 REBAR,12" O.C. EACH WAY
1'-6
"
(3) 5" DIA.COMBINEDCENTER POSTSBENCH SUPPORTSBELOW (3)
BENCH
1'-6
"
R1'-1
1"
3'-1
1"
2" DIA. TUBED STEEL
METAL MESHBENCH SEAT
SECTION BENCH PLAN ISOMETRIC
4 LS-502
SITE DETAILS
CH
ILD
RE
N'S
HO
SP
ITA
L C
OL
OR
AD
O
CA
NIN
E R
ES
PIT
E A
RE
A
SHEET NUMBER
DATE ISSUED:
SCALE:
10/14/2020
REVISIONS:
No. DATE DESCRIPTION
DESIGNED BY:DRAWN BY:CHECKED BY:
SEAL:
BY
11-03-20 DD SUBMITTAL
SHEET TITLE
AMERISTAR WIREWORKS PLUS FENCE1/2" = 1'-0"
8' O.C. Nom.
Standard Heights (Nominal)4', 5', 6' & 8'(6' displayed)
36" Min.Footing depth
2" Nom.
NOTES:1.) Post size depends on fence height and wind loads. See WIREWORKS PLUS post sizing chart.2.) Number of Architectural "V" folds varies with height. 4' height (2 folds), 5' height (2 folds), 6' height (3 folds), and 8'
height (4 folds).
Post size varies with Height(See WIREWORKS Post-Sizing chart)TM
1
TM
UPX25/UPX25WGA/B
LINE BRACKETSEND/GATE BRACKET
"No Mar" Polyester Color CoatEpoxy Powder Coat
Zinc PhosphateGalvanized Steel
Reinforcing Architectural "V" fold.(Note: Number of folds vary with height)
2
2"
6"
3"6 Gauge
Values shown are nominal and not to beused for installation purposes. See productspecification for installation requirements.
2
DG AND FENCE1/2" = 1'-0"
7'
4"
8"
1'
3'
SYNLAWN PET SYSTEM ARTIFICIALTURF, SEE DETAIL FORINSTALLATION SPECIFICATIONS
AMERISTAR WIREWORKS PLUSFENCE, 5' HT., SEE DETAIL
5'
PLANTING AREA
3" DEEP SHREDDEDWOOD MULCH
6" ROLL TOP ALUMINUM EDGING RED SANDSTONE BREEZEWITH STABILIZER. INSTALLIN (2) - 2 INCH LIFTS
FILTER FABRIC
GRADE
1 2" 2X6 TREX NAILER BOARD,ATTACH WITH GALVANIZEDSCREWS
8" DIA. SONOTUBEFOOTING AT POSTS
COMPACT SUBGRADETO 95% SPD
12" WIDE X 6" DEEPCONCRETE BAND. BROOMFINISH ON HORIZONTALSURFACE. SCORE JOINT ATCENTER OF POST
5
www.synlawn.com
SYNLAWN2680 ABUTMENT ROAD SE
DALTON, GA 30721TOLL FREE: 1-866-SYNLAWN
FAX: (706) 277-1128®
CADdetails.comPROTECTED BY COPYRIGHT ©2020 CADDETAILS.COM LTD.REVISION DATE 11/03/2020
SYNLAWN PET PLATINUM - INSTALLED OVER AGGREGATE BASE
DRAINAGE PASS THROUGH FOR WATER INREGULAR GRID THROUGHOUT BACKING
90% COMPACTION
SYNTIPEDE PET PLATINUMW/ SUPER YARN™ GRASS FIBER
2-3"
1 1/2"
AT LE
AST
2"
CONCRETE CURB(OPTIONAL)
1 1/2"
4-6"
NOT TO SCALE
SECURING THE GRASS TO THE BASE
GALVANIZED FLATHEAD SYNTHETICGRASS SPIKES 6" TO12" APART ALONGPERIMETER.
SYNLAWN PET SYSTEM
ENVIROLOC™ BACKINGSYSTEM
COMPACTED AGGREGATE BASE- CLASS II ROAD BASE, 1/4"
MINUS WITH FINES MIXED IN
NATURAL DIRT SUBGRADE(COMPACTED)
SPECIFICATIONSPRODUCT SKU:GRASS ZONE YARN/COLOR:GRASS ZONE DENIER:THATCH ZONE YARN/COLOR:THATCH ZONE DENIER:GRASS ZONE YARN SHAPE:FINISHED PILE HEIGHT:FINISHED PILE WEIGHT:BACKING:TUFT GAUGE:TOTAL WEIGHT:TUFF BIND:
NOTE: THE GRASS MUST BE INSTALLED AND SEAMED WITH ADJACENT PIECESRUNNING IN THE SAME DIRECTION; SEAMS SHOULD BE GLUED WITH SUITABLESEAMING GLUE AND SEAMING CLOTH, NOT ADHESIVE TAPE.
FALL RATING:PERMEABILITY:FEATURES:
TEST DATA:
IPEMA CERTIFIED> 1,200 INCHES PER /SYSANITIZED®, ENVIROLOC™, STATBLOCK™,DUALCHILL™, DELUSTER, UV STABILIZERSASTM E108 CLASS A FIRE RATING,ASTM F1292, ASTM F1551, ASTM F1951
SYNLAWN PET PLATINUMPE SUPER YARN™ FIELD / APPLE10,000/6FIELD GREEN/BEIGE5,040/12OMEGA1 1/2"80 OZ.15/18 PP 2-PART, 20 OZ ENVIROLOC™3/8"106 OZ.> 8 LBS.
1437-312
NOTES:
2. INSTALLATION TO BE COMPLETED IN ACCORDANCE WITH SPECIFICATIONS BY FACTORY AUTHORIZED INSTALLERS.3. DO NOT SCALE DRAWINGS.4. CONTRACTORS NOTE: FOR PRODUCT AND COMPANY INFORMATION VISIT www.CADdetails.com/info REFERENCE NUMBER 1437-312.
ODOR REDUCING TOP DRESSINGPER SPECIFICATIONS:
RESIDENTIAL (1-4LBS. PER FT2)
GEOTEXTILE WEED BARRIER(OPTIONAL)
1. FOR PET INSTALLS IT IS RECOMMENDED TO RINSE DAILY TO PREVENT ODORS REGARDLESS OF PET DEODORIZER USE.
BENDER BOARD(1/2"-3/4" BELOW CONCRETE EDGE)NAIL OR SCREW FROM TOP
SYNLAWN PET SYSTEM1" = 1'-0"
1
NEOLIVIANO BENCH1/2" = 1'-0"
GRADE
MANUFACTURER: LANDSCAPE FORMSMODEL: NEOLIVIANO BENCH, BACKED, 69 IN,SURFACE MOUNT, WOODNOTES:INSTALL PER MANUFACTURER'S SPECIFICATIONS
CIP CONCRETEFOOTER, 4 PERBENCH, INSTALLPLUMB AND LEVEL
COMPACTSUBGRADE TO95% SPD
4"
1'
6"
DG, MIN. 12" COVER
4
LINK BENCHN.T.S.
MANUFACTURER: LANDSCAPE FORMSMODEL: (2) LINK BENCH, PIANO KEY, (1) 140 IN. CENTERLINE AND (1)MODIFIED CUSTOM RADII, INSIDE FULL BACKREST, NO ARMS, METAL LEGSNOTES:INSTALL PER MANUFACTURER'S SPECIFICATIONSLINK BENCH A: 140" RADIUS, 2 SEGMENTSLINK BENCH B: MODIFIED CUSTOM RADIUS, 3 SEGMENTS
3
WAYFINDING SIGNN.T.S.
NOTES:CUSTOM FABRICATED
6LS-503
SITE DETAILS
BUILDING
BUILDING
(2,217 sf) TUR SOD
(40) COT ACU
(70) LAM SIL
(7) ULM EP2
(12) MIS GRA
(15) MIS GRA
(51) LIG LOD
ARTIFICIAL TURF (4,113 sf)
(30) LIG LOD(14) MIS GRA
(30) CAR MRO
(26) ANE SYL
(34) HEU RBE
(13) DIC SP2
(47) SED AU3(65) GAL ODO
(9) HEU RBE
(13) CAR MRO
(11) SED AU3
(42) GAL ODO
TREES CODE QTY BOTANICAL / COMMON NAME SIZE
ULM EP2 7 ULMUS DAVIDIANA JAPONICA `MORTON` TM 3" CALACCOLADE ELM
SHRUBS CODE QTY BOTANICAL / COMMON NAME SIZE
COT ACU 40 COTONEASTER ACUTIFOLIUS 7 GALPEKING COTONEASTER
LIG LOD 81 LIGUSTRUM VULGARE `LODENSE` 2 GALLODENSE PRIVET
MIS GRA 41 MISCANTHUS SINENSIS `GRACILLIMUS` 5 GALMAIDEN GRASS
GROUND COVERS CODE QTY BOTANICAL / COMMON NAME SIZE SPACING
4,113 SF ARTIFICIAL TURF
ANE SYL 26 ANEMONE SYLVESTRIS 1 GAL 18" o.c.SNOWDROP ANEMONE
CAR MRO 43 CAREX MORROWII 1 GAL 18" o.c.JAPANESE SEDGE
DIC SP2 13 DICENTRA SPECTABILIS 1 GAL 24" o.c.BLEEDING HEART
GAL ODO 107 GALIUM ODORATUM FLATS 12" o.c.SWEET WOODRUFF
HEU RBE 43 HEUCHERA X `ROOT BEER` 1 GAL 18" o.c.ROOT BEER CORAL BELLS
LAM SIL 69 LAMIUM MACULATUM `BEACON SILVER` 1 GAL 18" o.c.BEACON SILVER LAMIUM
SED AU3 58 SEDUM X `AUTUMN JOY` 1 GAL 18" o.c.AUTUMN JOY SEDUM
TUR SOD 2,223 SF TURF SOD SODDROUGHT TOLERANT FESCUE BLEND
PLANT SCHEDULE
NORTH
0 5' 10' 20'
SCALE: 1" = 10'-0"
CH
ILD
RE
N'S
HO
SP
ITA
L C
OL
OR
AD
O
CA
NIN
E R
ES
PIT
E A
RE
A
SHEET NUMBER
DATE ISSUED:
SCALE:
10/14/2020
REVISIONS:
No. DATE DESCRIPTION
DESIGNED BY:DRAWN BY:CHECKED BY:
SEAL:
BY
11-03-20 DD SUBMITTAL
SHEET TITLE
1" = 10'
LP-101
PLANTING PLAN
CH
ILD
RE
N'S
HO
SP
ITA
L C
OL
OR
AD
O
CA
NIN
E R
ES
PIT
E A
RE
A
SHEET NUMBER
DATE ISSUED:
SCALE:
10/14/2020
REVISIONS:
No. DATE DESCRIPTION
DESIGNED BY:DRAWN BY:CHECKED BY:
SEAL:
BY
11-03-20 DD SUBMITTAL
SHEET TITLE
LP-102
PLANT PALETTE
CH
ILD
RE
N'S
HO
SP
ITA
L C
OL
OR
AD
O
CA
NIN
E R
ES
PIT
E A
RE
A
SHEET NUMBER
DATE ISSUED:
SCALE:
10/14/2020
REVISIONS:
No. DATE DESCRIPTION
DESIGNED BY:DRAWN BY:CHECKED BY:
SEAL:
BY
11-03-20 DD SUBMITTAL
SHEET TITLE
2 X ROOTBALLDIAMETER NOTE:INCORPORATE LIQUID ROOT STIMULANT
AS PART OF PLANTING OPERATION
SHRUB PLANTING1/2" = 1'-0"
3" DEEP SHREDDED WOOD MULCH
PLANT CROWN 1" ABOVE FINISH GRADE
PLANTING MIXSCARIFY SIDES OF HOLE PRIOR TO BACK-FILLINGREMOVE PLANT FROM CONTAINER OR PEELBACK BURLAP AND REMOVE TWINE / WIREFROM ROOT BALL AFTER 23 BURIED IN PIT.PLACE ON UNDISTURBED SUBGRADE
1 GROUNDCOVER AND PERENNIAL PLANTING1" = 1'-0"
SPACE GROUNDCOVER OR PERENNIAL
TO SPECIFIED TRIANGULAR SPACING
3" DEEP SHREDDEDWOOD MULCH
PLANTING MIX
SUBGRADE
12"
2
EDGE OF PAVING,WALL, PLANTER BED
OR HEADER (SEEPLANS)
FOR TRIANGULAR SPACING OF SHRUBS,PERENNIALS AND GROUNDCOVERS.
SEE PLANT SPACING DISTANCE.
12P P P
R
P
P
P
P
1 2 P
PTRIANGULAR
4"6"8"
10"12"18"24"30"3'4'5'6'
RROW3 716"5 14"7"
8 3 4"10 3 8"1'-3 5 8"1'-8 3 4"
2'-2"2'-7"
3'-5 12"4'-4"
5'-2 3 8"
AREA PER PLANTSQ.FT..096.22.385.60.871.953.465.427.80
13.8421.6531.20
SHRUB AND PERENNIAL SPACING3/8" = 1'-0"
3
TREE STAKING IN OPEN SPACESTREE GUYING OR THREE STAKE LAYOUT TREE STAKING ALONG ROADS OR WALKS
120°
120°
120°
180°180°
EDGE OF WALK ORCURB
ALIGN (2) POSTS ORSTAKES PARALLEL WITHROAD OR WALKS
ALIGN STAKES PARALLELWITH DIRECTION OFPREVAILING WIND. ALLSTAKES TO BECONSISTENT ALIGNMENT.
ALIGN STAKESPARALLEL WITH ROADOR WALKS
EDGE OF WALK ORCURB
TREE STAKING & GUYING1/2" = 1'-0"
DIRECTION OFPREVAILING WIND
6
TREE PLANTING DETAIL6" = 1'-0"
DO NOT CUT SINGLE LEADER. PRUNE ONLY DAMAGED,
DEAD WOOD, OR CO-DOMINANT LEADERS AT CITY
FORESTER'S DIRECTION.
12" NYLON TREE STRAP WITH GROMMETS ON GUY WIRE. DO NOT TWISTS STRAPS TO
TIGHTEN AROUND TRUNK.
1/2" DIAMETER WHITE PVC PIPE SECTION ON ENTIRE LENGTH OF EACH WIRE.
14-GAUGE GALVANIZED WIRE, DOUBLE STRAND. LEAVE 1-2" SLACK IN WIRE TO ALLOW
FOR TRUNK MOVEMENT.
IF NEEDED, 6' STEEL T-POST OR WOOD STAKE (4' EXPOSED, 2' IN UNDISTURBED
SUBGRADE) WITH SAFETY CAPS, SET TO WINDWARD SIDE AND OTHER OPPOSITE; OR
OTHER PRE-APPROVED STAKING METHOD.
DECIDUOUS TREE FALL PLANTING: WRAP TRUNK TO FIRST BRANCH WITH SPECIFIED
TREE WRAP MATERIAL. SECURE AT TOP WITH MASKING TAPE. DO NOT WRAP ROUGH
BARK, POPULUS, OR GLEDITSIA TREES. REMOVE IN SPRING AS SPECIFIED.
SET ROOT COLLAR 2 TO 3" HIGHER THAN FINISHED GRADE. REMOVE EXCESS SOIL
FROM TOP OF ROOT BALL.
CIRCLE OF SHREDDED WOOD MULCH, 3" DEEP AND 4-6" AWAY FROM TRUNK, TO
OUTER EDGE OF PLANTING HOLE.
FORM 2" HIGH DIRT SAUCER AROUND PIT AT OUTSIDE OF TRANSITION ZONE.
FINISH GRADE
COMPLETELY REMOVE ALL TWINE AND WIRE BASKET. PULL BURLAP DOWN MINIMUM
OF 2/3, CUT AND REMOVE FROM PIT.
SLOPE SIDES OF PLANTING PIT AS SHOWN, ROUGHEN SIDES PRIOR TO BACKFILL.
SPECIFIED BACKFILL MIXTURE (INCLUDE NATIVE SOIL WHERE POSSIBLE).
UNDISTURBED SUBGRADE
ANY BROKEN, CRUMBLING, OR OTHERWISE DAMAGED ROOTBALL WILL BE
REJECTED. DAMAGE DURING PLANTING OPERATIONS WILL NOT BE EXCUSED.2X ROOTBALL DIAMETER
3-4 X ROOT BALL DIAMETER
12 X X
12 X
5
ORNAMENTAL GRASS PLANTING1" = 1'-0"
12"
SET ORNAMENTAL GRASS TOSPECIFIED TRIANGULAR SPACING
RE: PLANT SCHEDULE
SUBGRADE
PLANTING MIX 12"DEPTH, MIN.
3" WOOD MULCH, RE:SPECS
P-DOG-214
LP-501
PLANTING DETAILS