CAMBRI-LINK CAMBRI-LINK SPECIFICATIONS STANDARD … · durable, efficient belting for spiral cage...
6
CAMBRI-LINK DURABLE, EFFICIENT BELTING FOR SPIRAL CAGE AND STRAIGHT-LINE APPLICATIONS POSITIVE DRIVE • FULLY COLLAPSIBLE LARGE OPEN AREAS PROVEN RESULTS APPLICATIONS BAKING COOLING FREEZING PROOFING TRANSFERS WASHING A potato products company noticed a significant decrease in product throughput when they changed their spiral freezer to plastic belting. They then decided to try Cambri-Link belting, and their throughput immediately increased. Cambri- Link provided much better air flow and was more efficient than the plastic belting. • Rugged flat wire style belt • Efficient and economical • For straight-line and spiral applications Fully collapsible construction for easy cleaning: each picket has an oblong slot that holds the rod, which allows better access for sanitation and reduced area for bacteria build-up Large open mesh area for efficient air circulation and drainage Smooth, flat surface for excellent product stability + Positive drive system for a continuous product flow that is smooth and vibration-free ALL CAMBRI-LINK BELTS PROVIDE INDUSTRY-LEADING BENEFITS: 2.2 x Belt Width (Nominal Inside) STANDARD RADIUS CAMBRI-LINK -OR- LEADING EDGE PERFORMANCE LINK** *Cambri-Link belts are also available for straight running applications. **Leading Edge Performance Link belts are available for spiral systems with high tangential tension ratings (600 lbs. or more) 1 SIDE VIEW: CAMBRI-LINK PICKETS BELT TURNING RADIUS* Down to 1.5 x Belt Width REDUCED RADIUS CAMBRI-LINK -OR- LEADING EDGE PERFORMANCE LINK** Down to 1.0 x Belt Width TIGHT RADIUS CAMBRI-LINK •
Transcript of CAMBRI-LINK CAMBRI-LINK SPECIFICATIONS STANDARD … · durable, efficient belting for spiral cage...
CAMBRI-LINKDURABLE, EFFICIENT BELTING FOR SPIRAL CAGE AND STRAIGHT-LINE APPLICATIONS
POSITIVE DRIVE • FULLY COLLAPSIBLE LARGE OPEN AREAS
CAMBRI-LINK SPECIFICATIONSSTANDARD RADIUS BELTS
CAMBRI-LINK SPECIFICATIONS: STANDARD RADIUS BELTSBELT PITCH 1” (25.4 mm)
MESH SIZES 1/2” x 1” (12.7 x 25.4 mm)1” x 1” (25.4 x 25.4 mm)
FLAT STRIP Extra Heavy Duty: 1/2” x .0625” (12.7 x 1.59 mm)
RODS Extra Heavy Duty: 6 gauge – 0.192” (4.9 mm) diameter
BELT TURNING RADIUS Nominal inside turning radius is 2.2 x belt widthCustom confi gurations available for oversized (>2.2) radii
BELT WIDTH RANGE 12” to 48” (305 mm to 1,219 mm) standard. Custom widths available
MATERIALS Wear resistant stainless steel (WRSS) throughout, standard.Also available in T304 or T316 stainless steel, high carbon steel (HCS), or galvanized steel.
WELDING Button head welds on rods
EDGE REINFORCEMENT Furnished with double reinforcing bars on both edges, unless otherwise specifi ed
SPECIAL CONSTRUCTIONSExtra heavy duty reinforcing bars available for added tension capabilitiesSide plates and lane dividers availableOther special constructions and attachments are available for unique applications
TENSION LIMITS*
*For double reinforcement edge construction
BELT TYPE STRAIGHT RUNNING TURN OR SPIRAL(DOUBLE BARS ON BOTH SIDES)
1/2” x 1” standard mesh 1,700 lbs./ft. (2,530 kg/M) 200 lbs./ft. (297 kg/M)
1/2” x 1” extra heavy duty mesh 1,700 lbs./ft. (2,530 kg/M) 400 lbs./ft (595 kg/M)
1” x 1” standard mesh 1,350 lbs./ft. (2,009 kg/M) 200 lbs./ft. (297 kg/M)
1” x 1” extra heavy duty mesh 1,350 lbs./ft. (2,009 kg/M) 400 lbs./ft (595 kg/M)
CAMBRI-LINK MESH PATTERN
CAMBRI-LINK BELT WEIGHTS:STANDARD & REDUCED RADIUS
BELT WIDTH WEIGHT PER UNIT LENGTH OF BELT1/2” X 1” MESH 1” X 1” MESH
IN. MM LBS./LIN.FT. KG/LIN. M LBS./LIN.FT. KG/LIN. M
12 305 3.24 4.82 2.94 4.37
14 356 3.78 5.62 3.43 5.10
16 406 4.32 6.43 3.92 5.83
18 457 4.86 7.23 4.41 6.56
20 508 5.40 8.04 4.90 7.29
22 559 5.94 8.84 5.39 8.02
24 610 6.48 9.64 5.88 8.75
26 660 7.02 10.45 6.36 9.46
28 711 7.56 11.25 6.85 10.19
30 762 8.10 12.05 7.34 10.92
32 813 8.64 12.86 7.83 11.65
34 864 9.18 13.66 8.32 12.38
36 914 9.72 14.46 8.81 13.11
38 965 10.26 15.27 9.30 13.84
40 1,016 10.80 16.07 9.79 14.57
42 1,067 11.34 16.87 10.28 15.30
44 1,118 11.88 17.68 10.77 16.03
46 1,168 12.42 18.48 11.26 16.75
48 1,219 12.96 19.28 11.75 17.49
PROVEN RESULTS
APPLICATIONSBAKING
COOLING
FREEZING
PROOFING
TRANSFERS
WASHING
A potato products company noticed a signifi cant decrease in product throughput when they changed their spiral freezer to plastic belting. They then decided to try Cambri-Link belting, and their throughput immediately increased. Cambri-Link provided much better air fl ow and was more effi cient than the plastic belting.
• Rugged fl at wire style belt
• Effi cient and economical
• For straight-line and spiral applications
Fully collapsible construction for easy cleaning: each picket has an oblong slot that holds the rod, which allows better access for sanitation and reduced area for bacteria build-up
Large open mesh area for effi cient air circulation and drainage
Smooth, fl at surface for excellent product stability
+ Positive drive system for a continuous product fl ow that is smooth and vibration-free
ALL CAMBRI-LINK BELTS PROVIDE INDUSTRY-LEADING BENEFITS:
2.2 x Belt Width (Nominal Inside)STANDARD RADIUS
CAMBRI-LINK-OR-
LEADING EDGEPERFORMANCE LINK**
*Cambri-Link belts are also available for straight running applications.**Leading Edge Performance Link belts are available for spiral systems with high tangential tension ratings (600 lbs. or more)
1 2
SIDE VIEW: CAMBRI-LINK PICKETS
BELT TURNING RADIUS*Down to 1.5 x Belt Width
REDUCED RADIUS CAMBRI-LINK
-OR-LEADING EDGE
PERFORMANCE LINK**
Down to 1.0 x Belt WidthTIGHT RADIUS CAMBRI-LINK
•
CAMBRI-LINKDURABLE, EFFICIENT BELTING FOR SPIRAL CAGE AND STRAIGHT-LINE APPLICATIONS
POSITIVE DRIVE • FULLY COLLAPSIBLE LARGE OPEN AREAS
CAMBRI-LINK SPECIFICATIONSSTANDARD RADIUS BELTS
CAMBRI-LINK SPECIFICATIONS: STANDARD RADIUS BELTSBELT PITCH 1” (25.4 mm)
MESH SIZES 1/2” x 1” (12.7 x 25.4 mm)1” x 1” (25.4 x 25.4 mm)
FLAT STRIP Extra Heavy Duty: 1/2” x .0625” (12.7 x 1.59 mm)
RODS Extra Heavy Duty: 6 gauge – 0.192” (4.9 mm) diameter
BELT TURNING RADIUS Nominal inside turning radius is 2.2 x belt widthCustom confi gurations available for oversized (>2.2) radii
BELT WIDTH RANGE 12” to 48” (305 mm to 1,219 mm) standard. Custom widths available
MATERIALS Wear resistant stainless steel (WRSS) throughout, standard.Also available in T304 or T316 stainless steel, high carbon steel (HCS), or galvanized steel.
WELDING Button head welds on rods
EDGE REINFORCEMENT Furnished with double reinforcing bars on both edges, unless otherwise specifi ed
SPECIAL CONSTRUCTIONSExtra heavy duty reinforcing bars available for added tension capabilitiesSide plates and lane dividers availableOther special constructions and attachments are available for unique applications
TENSION LIMITS*
*For double reinforcement edge construction
BELT TYPE STRAIGHT RUNNING TURN OR SPIRAL(DOUBLE BARS ON BOTH SIDES)
1/2” x 1” standard mesh 1,700 lbs./ft. (2,530 kg/M) 200 lbs./ft. (297 kg/M)
1/2” x 1” extra heavy duty mesh 1,700 lbs./ft. (2,530 kg/M) 400 lbs./ft (595 kg/M)
1” x 1” standard mesh 1,350 lbs./ft. (2,009 kg/M) 200 lbs./ft. (297 kg/M)
1” x 1” extra heavy duty mesh 1,350 lbs./ft. (2,009 kg/M) 400 lbs./ft (595 kg/M)
CAMBRI-LINK MESH PATTERN
CAMBRI-LINK BELT WEIGHTS:STANDARD & REDUCED RADIUS
BELT WIDTH WEIGHT PER UNIT LENGTH OF BELT1/2” X 1” MESH 1” X 1” MESH
IN. MM LBS./LIN.FT. KG/LIN. M LBS./LIN.FT. KG/LIN. M
12 305 3.24 4.82 2.94 4.37
14 356 3.78 5.62 3.43 5.10
16 406 4.32 6.43 3.92 5.83
18 457 4.86 7.23 4.41 6.56
20 508 5.40 8.04 4.90 7.29
22 559 5.94 8.84 5.39 8.02
24 610 6.48 9.64 5.88 8.75
26 660 7.02 10.45 6.36 9.46
28 711 7.56 11.25 6.85 10.19
30 762 8.10 12.05 7.34 10.92
32 813 8.64 12.86 7.83 11.65
34 864 9.18 13.66 8.32 12.38
36 914 9.72 14.46 8.81 13.11
38 965 10.26 15.27 9.30 13.84
40 1,016 10.80 16.07 9.79 14.57
42 1,067 11.34 16.87 10.28 15.30
44 1,118 11.88 17.68 10.77 16.03
46 1,168 12.42 18.48 11.26 16.75
48 1,219 12.96 19.28 11.75 17.49
PROVEN RESULTS
APPLICATIONSBAKING
COOLING
FREEZING
PROOFING
TRANSFERS
WASHING
A potato products company noticed a signifi cant decrease in product throughput when they changed their spiral freezer to plastic belting. They then decided to try Cambri-Link belting, and their throughput immediately increased. Cambri-Link provided much better air fl ow and was more effi cient than the plastic belting.
• Rugged fl at wire style belt
• Effi cient and economical
• For straight-line and spiral applications
Fully collapsible construction for easy cleaning: each picket has an oblong slot that holds the rod, which allows better access for sanitation and reduced area for bacteria build-up
Large open mesh area for effi cient air circulation and drainage
Smooth, fl at surface for excellent product stability
+ Positive drive system for a continuous product fl ow that is smooth and vibration-free
ALL CAMBRI-LINK BELTS PROVIDE INDUSTRY-LEADING BENEFITS:
2.2 x Belt Width (Nominal Inside)STANDARD RADIUS
CAMBRI-LINK-OR-
LEADING EDGEPERFORMANCE LINK**
*Cambri-Link belts are also available for straight running applications.**Leading Edge Performance Link belts are available for spiral systems with high tangential tension ratings (600 lbs. or more)
1 2
SIDE VIEW: CAMBRI-LINK PICKETS
BELT TURNING RADIUS*Down to 1.5 x Belt Width
REDUCED RADIUS CAMBRI-LINK
-OR-LEADING EDGE
PERFORMANCE LINK**
Down to 1.0 x Belt WidthTIGHT RADIUS CAMBRI-LINK
TIGHT (1.0) RADIUS BELTING
CAMBRI-LINK SPECIFICATIONSREDUCED RADIUS BELTS
CAMBRI-LINK SPECIFICATIONSTIGHT RADIUS BELTS
CAMBRI-LINK SPECIFICATIONS: TIGHT RADIUS BELTSSpecifi cations for Cambri-Link Tight Radius belts are the same as Cambri-Link Standard belts, except as noted below:
MESH SIZES(INNER | OUTER)
1/2” x 1” | 1/2” x 1-1/2” (12.7 x 25.4 mm | 12.7 x 38.1 mm)1” x 1” | 1/2” x 1-1/2” (25.4 x 25.4 mm | 12.7 x 38.1 mm)1” x 1” | 1” x 1-1/2” (25.4 x 25.4 mm | 25.4 x 38.1 mm)
FLAT STRIP Inner Section: 1/2” x .0625” (12.7 x 1.59 mm)Outer Section: 1/2” x .0460” (12.7 x 1.17 mm)
BELT TURNING RADIUS 1.0 x belt width to 2.0 x belt widthOther belt radii possible for custom applications
MATERIALS Wear resistant stainless steel (WRSS) throughout, standardAlso available in T304 or T316 stainless steel, or high carbon steel (HCS)
EDGE REINFORCEMENTStandard: extra heavy duty double reinforcing bars form an internal tension-bearing row; no reinforcement on belt edgesSingle or double reinforcing bars are available for one or both edges
SPECIAL CONSTRUCTIONS Extended bar side plates availableLane dividers available
SPROCKETS Uses standard sprockets for 1” pitch Cambri-Link belts
TANGENTIAL TENSION
TYPE OF BELT*
Straight Run Application Turn or Spiral Application
Tension per Unit of Belt Width Total Allowable Tension
lbs./ft. kg/M lbs. kg
1/2” x 1” | 1/2” x 1-1/2” 850 1,265 400 181.4
1” x 1” | 1/2” x 1-1/2” 675 1,005 400 181.4
1” x 1” | 1” x 1-1/2” 675 1,005 400 181.4
*Double extra heavy duty reinforcement edge construction
• Constructed with two turn belts that share a common rod • Inner section is a 1/2” x 1” or 1” x 1” Cambri-Link mesh belt • Outer section has an elongated pitch to allow for the necessary edge extension
• Generally has no reinforcement on the inner or outer belt edges; however, single or double reinforcing bars are available
• Tight turning radius of 1.0 x belt width
TIGHT (1.0) RADIUS BELTING
TIGHT RADIUS CAMBRI-LINK
CAMBRI-LINK SPECIFICATIONS: REDUCED RADIUS BELTSSpecifi cations for Cambri-Link Reduced Radius belts are the same as Cambri-Link Standard Radius belts, except as noted below:
BELT TURNING RADIUS 1.5 belt width to 2.0 x belt widthOther belt radii possible for custom applications
EDGE REINFORCEMENT1.7 Radius belts are constructed with single reinforcing bars along the inside belt edge1.5 Radius belts eliminate the reinforcing bars on the inside belt edgeReduced radius belts cannot be fl ipped
SPECIAL CONSTRUCTIONSExtra heavy duty reinforcing bars are available for the outside belt edgeLane dividers and side plates are availableFor 1.5 Radius belts, side plates may only be used on the outside belt edge
SPROCKETS Uses standard Cambri-Link sprockets
TANGENTIAL TENSION
TYPE OF BELT*Straight Run Application
Turn or Spiral ApplicationSingle Bar on Inside
Double Bars on Outside
lbs./ft. kg/M lbs. kg
1/2” x 1” 1,700 2,530 400 181.4
1” x 1” 1,350 2,009 400 181.4
*Double extra heavy duty reinforcement edge construction
REDUCED RADIUS CAMBRI-LINK
• Saves valuable fl oor space
• Provides greater throughput because a wider belt can be used in the same amount of fl oor space
• Reduces energy costs due to greater load capacity in smaller systems
• Constructed with no central links or bars to interfere with product placement
REDUCED (1.5) RADIUS BELTING
CAMBRI-LINK WITH LANE DIVIDERS (Available for all Cambri-Link belts)
3 4
TIGHT (1.0) RADIUS BELTING
CAMBRI-LINK SPECIFICATIONSREDUCED RADIUS BELTS
CAMBRI-LINK SPECIFICATIONSTIGHT RADIUS BELTS
CAMBRI-LINK SPECIFICATIONS: TIGHT RADIUS BELTSSpecifi cations for Cambri-Link Tight Radius belts are the same as Cambri-Link Standard belts, except as noted below:
MESH SIZES(INNER | OUTER)
1/2” x 1” | 1/2” x 1-1/2” (12.7 x 25.4 mm | 12.7 x 38.1 mm)1” x 1” | 1/2” x 1-1/2” (25.4 x 25.4 mm | 12.7 x 38.1 mm)1” x 1” | 1” x 1-1/2” (25.4 x 25.4 mm | 25.4 x 38.1 mm)
FLAT STRIP Inner Section: 1/2” x .0625” (12.7 x 1.59 mm)Outer Section: 1/2” x .0460” (12.7 x 1.17 mm)
BELT TURNING RADIUS 1.0 x belt width to 2.0 x belt widthOther belt radii possible for custom applications
MATERIALS Wear resistant stainless steel (WRSS) throughout, standardAlso available in T304 or T316 stainless steel, or high carbon steel (HCS)
EDGE REINFORCEMENTStandard: extra heavy duty double reinforcing bars form an internal tension-bearing row; no reinforcement on belt edgesSingle or double reinforcing bars are available for one or both edges
SPECIAL CONSTRUCTIONS Extended bar side plates availableLane dividers available
SPROCKETS Uses standard sprockets for 1” pitch Cambri-Link belts
TANGENTIAL TENSION
TYPE OF BELT*
Straight Run Application Turn or Spiral Application
Tension per Unit of Belt Width Total Allowable Tension
lbs./ft. kg/M lbs. kg
1/2” x 1” | 1/2” x 1-1/2” 850 1,265 400 181.4
1” x 1” | 1/2” x 1-1/2” 675 1,005 400 181.4
1” x 1” | 1” x 1-1/2” 675 1,005 400 181.4
*Double extra heavy duty reinforcement edge construction
• Constructed with two turn belts that share a common rod • Inner section is a 1/2” x 1” or 1” x 1” Cambri-Link mesh belt • Outer section has an elongated pitch to allow for the necessary edge extension
• Generally has no reinforcement on the inner or outer belt edges; however, single or double reinforcing bars are available
• Tight turning radius of 1.0 x belt width
TIGHT (1.0) RADIUS BELTING
TIGHT RADIUS CAMBRI-LINK
CAMBRI-LINK SPECIFICATIONS: REDUCED RADIUS BELTSSpecifi cations for Cambri-Link Reduced Radius belts are the same as Cambri-Link Standard Radius belts, except as noted below:
BELT TURNING RADIUS 1.5 belt width to 2.0 x belt widthOther belt radii possible for custom applications
EDGE REINFORCEMENT1.7 Radius belts are constructed with single reinforcing bars along the inside belt edge1.5 Radius belts eliminate the reinforcing bars on the inside belt edgeReduced radius belts cannot be fl ipped
SPECIAL CONSTRUCTIONSExtra heavy duty reinforcing bars are available for the outside belt edgeLane dividers and side plates are availableFor 1.5 Radius belts, side plates may only be used on the outside belt edge
SPROCKETS Uses standard Cambri-Link sprockets
TANGENTIAL TENSION
TYPE OF BELT*Straight Run Application
Turn or Spiral ApplicationSingle Bar on Inside
Double Bars on Outside
lbs./ft. kg/M lbs. kg
1/2” x 1” 1,700 2,530 400 181.4
1” x 1” 1,350 2,009 400 181.4
*Double extra heavy duty reinforcement edge construction
REDUCED RADIUS CAMBRI-LINK
• Saves valuable fl oor space
• Provides greater throughput because a wider belt can be used in the same amount of fl oor space
• Reduces energy costs due to greater load capacity in smaller systems
• Constructed with no central links or bars to interfere with product placement
REDUCED (1.5) RADIUS BELTING
CAMBRI-LINK WITH LANE DIVIDERS (Available for all Cambri-Link belts)
3 4
CAMBRIDGE ENGINEERED SOLUTIONS877.649.7492 +1.410.901.2660
LEADING EDGE PERFORMANCE GRID
•Designed for systems with high tangential tension ratings of 600 lbs. or more (272+ kg)
• Operates at sustained speeds up to 150 feet per minute (45.7 meters per minute)
• Weight-bearing capacity of 15 lbs. per linear foot or more (22+ kg per meter)
• Collapses down to a 1.5 turn radius ratio
• Constructed with double rows of extra heavy duty reinforcing bars plus three rows of heavy duty links on the outside edge
LEADING EDGE PERFORMANCE LINK SPROCKETS
NO. OF TEETH/SPROCKET
DESIGNATION
PITCH DIAMETER
BOTTOM DIAMETER
HUB LENGTH
BORE SIZESPROCKET THICKNESS
APPROXIMATE WEIGHT
IN MM IN MM IN MM IN MM LBS KG LBS KG
18E 6.117 155.4 5.617 142.7 2.0 50.8 1.0 - 4.0 25.4 - 101.6 2.0 50.8 1.5 0.68
23E 7.875 200.0 7.368 187.1 2.0 50.8 1.0 - 4.0 25.4 - 101.6 2.0 50.8 1.2 0.54
Materials: UHMW and Stainless Steel
LEADING EDGE PERFORMANCE LINKSpecifi cations for LE Performance Link belts are the same as Cambri-Link Standard belts, except as noted below:
BELT PITCH 1” (25.4 mm) nominal
BELT TURNING RADIUS Down to 1.5 x belt width
BELT WIDTH RANGE 12” to 60” standard (305 to 1,524 mm)
MATERIALS Wear Resistant Stainless Steel (WRSS)
TENSION LIMITS Tangential tension rating of 600 lbs. (272 kg) or more
LEADING EDGE PERFORMANCE LINK
CAMBRI-LINK SPROCKETS
NO. OF TEETH/
SPROCKETDESIG.
NOMINALDIAMETER
OVERALLDIAMETER
PITCH DIAMETER
HUB DIA.(BOTTOM
DIAMETER)HUB
LENGTHFACE
WIDTHAPPROX.WEIGHT
BORE SIZE
IN MM IN MM IN MM IN MM IN MM IN MM LBS KG IN MM
Cambri-Link E-Code Steel and Stainless Steel Sprockets for 1” x 1” and 1/2” x 1” Belts
13E 4 101.6 4.850 123.2 4.350 110.5 - - 2.000 50.8 1.5 38.1 5 2.27 3/4 to 1-5/8 19.1 to 41.3
18E 6 152.4 6.617 168.1 6.117 155.4 - - 2.000 50.8 1.5 38.1 9 4.08 3/4 to 2 19.1 to 50.8
23E 8 203.2 8.368 212.5 7.868 199.8 4.0 101.6 2.000 50.8 1.85 47.0 12 5.44 3/4 to 2-1/2 19.1 to 63.5
Cambri-Link E-Code UHMW Plastic Sprockets for 1” x 1” and 1/2” x 1” Belts
13E 4 101.6 4.850 123.2 4.350 110.5 - - 2.000 50.8 2.0 50.8 1.7 0.77 3/4 to 2 19.1 to 50.8
18E 6 152.4 6.617 168.1 6.117 155.4 5.617 142.7 2.000 50.8 2.0 50.8 1.5 0.68 3/4 to 3 19.1 to 76.2
23E 8 152.4 8.368 212.5 7.868 199.8 7.368 187.1 2.000 50.8 2.0 50.8 1.2 0.54 3/4 to 4 19.1 to 101.6
LEADING EDGE PERFORMANCE-GRID
5 6
SPROCKET INFORMATION
CAMBRI-LINK SPROCKET
CAMBRI-LINK & LEADING EDGE PERFORMANCE LINK
LEADING EDGE PERFORMANCE GRID
•Designed for systems with high tangential tension ratings of 600 lbs. or more (272+ kg)
• Operates at sustained speeds up to 150 feet per minute (45.7 meters per minute)
• Weight-bearing capacity of 15 lbs. per linear foot or more (22+ kg per meter)
• Collapses down to a 1.5 turn radius ratio
• Constructed with double rows of extra heavy duty reinforcing bars plus three rows of heavy duty links on the outside edge
LEADING EDGE PERFORMANCE LINK SPROCKETS
NO. OF TEETH/SPROCKET
DESIGNATION
PITCH DIAMETER
BOTTOM DIAMETER
HUB LENGTH
BORE SIZESPROCKET THICKNESS
APPROXIMATE WEIGHT
IN MM IN MM IN MM IN MM LBS KG LBS KG
18E 6.117 155.4 5.617 142.7 2.0 50.8 1.0 - 4.0 25.4 - 101.6 2.0 50.8 1.5 0.68
23E 7.875 200.0 7.368 187.1 2.0 50.8 1.0 - 4.0 25.4 - 101.6 2.0 50.8 1.2 0.54
Materials: UHMW and Stainless Steel
LEADING EDGE PERFORMANCE LINKSpecifi cations for LE Performance Link belts are the same as Cambri-Link Standard belts, except as noted below:
BELT PITCH 1” (25.4 mm) nominal
BELT TURNING RADIUS Down to 1.5 x belt width
BELT WIDTH RANGE 12” to 60” standard (305 to 1,524 mm)
MATERIALS Wear Resistant Stainless Steel (WRSS)
TENSION LIMITS Tangential tension rating of 600 lbs. (272 kg) or more
LEADING EDGE PERFORMANCE LINK
CAMBRI-LINK SPROCKETS
NO. OF TEETH/
SPROCKETDESIG.
NOMINALDIAMETER
OVERALLDIAMETER
PITCH DIAMETER
HUB DIA.(BOTTOM
DIAMETER)HUB
LENGTHFACE
WIDTHAPPROX.WEIGHT
BORE SIZE
IN MM IN MM IN MM IN MM IN MM IN MM LBS KG IN MM
Cambri-Link E-Code Steel and Stainless Steel Sprockets for 1” x 1” and 1/2” x 1” Belts
13E 4 101.6 4.850 123.2 4.350 110.5 - - 2.000 50.8 1.5 38.1 5 2.27 3/4 to 1-5/8 19.1 to 41.3
18E 6 152.4 6.617 168.1 6.117 155.4 - - 2.000 50.8 1.5 38.1 9 4.08 3/4 to 2 19.1 to 50.8
23E 8 203.2 8.368 212.5 7.868 199.8 4.0 101.6 2.000 50.8 1.85 47.0 12 5.44 3/4 to 2-1/2 19.1 to 63.5
Cambri-Link E-Code UHMW Plastic Sprockets for 1” x 1” and 1/2” x 1” Belts
13E 4 101.6 4.850 123.2 4.350 110.5 - - 2.000 50.8 2.0 50.8 1.7 0.77 3/4 to 2 19.1 to 50.8
18E 6 152.4 6.617 168.1 6.117 155.4 5.617 142.7 2.000 50.8 2.0 50.8 1.5 0.68 3/4 to 3 19.1 to 76.2
23E 8 152.4 8.368 212.5 7.868 199.8 7.368 187.1 2.000 50.8 2.0 50.8 1.2 0.54 3/4 to 4 19.1 to 101.6
LEADING EDGE PERFORMANCE-GRID
5 6
SPROCKET INFORMATION
CAMBRI-LINK SPROCKET
CAMBRI-LINK & LEADING EDGE PERFORMANCE LINK
