Calipers via laser
12
DIGITAL FABRICATION IN THE ARTS in the Cottage at the Western Pennsylvania School for the DEAF Edgewood, Pennsylvania, 2015 MAKING CALIPERS IN THE COTTAGE’s LASER CUTTER 1)Download Caliper file: http://www.thingiverse.com/thing:594 2) Open in Adobe Illustrator, your caliper should measure 7 inches across and 3.21 inches tall 3) Group the measurment indicator by dragging and holding down your mouse across the numbers and measurements. 1
-
Upload
fran-flaherty -
Category
Documents
-
view
224 -
download
4
description
Digital Fabrication in the Arts in the Cottage Western Pennsylvania School for the Deaf Edgewood, Pennsylvania Instructions for making Calipers at the Cottage
Transcript of Calipers via laser
DIGITAL FABRICATION IN THE ARTS in the Cottage at the Western Pennsylvania School for the DEAF
Edgewood, Pennsylvania, 2015
MAKING CALIPERS IN THE COTTAGE’s LASER CUTTER 1)Download Caliper file: http://www.thingiverse.com/thing:594
2) Open in Adobe Illustrator, your caliper should measure 7 inches across and 3.21 inches tall 3) Group the measurment indicator by dragging and holding down your mouse across the numbers and measurements.
1
DIGITAL FABRICATION IN THE ARTS in the Cottage at the Western Pennsylvania School for the DEAF
Edgewood, Pennsylvania, 2015
4) Move the measurement up a few millimeters to separate it from the caliper handle with the arrow keys or your mouse
5) Select the whole drawing
2
DIGITAL FABRICATION IN THE ARTS in the Cottage at the Western Pennsylvania School for the DEAF
Edgewood, Pennsylvania, 2015
3
DIGITAL FABRICATION IN THE ARTS in the Cottage at the Western Pennsylvania School for the DEAF
Edgewood, Pennsylvania, 2015
6) Shift click the measurement to deselect it from the group. Notice that the selected parts are in blue and the numbers and measurements are not in blue. The selected lines are the lines that you want the laser to cut
4
DIGITAL FABRICATION IN THE ARTS in the Cottage at the Western Pennsylvania School for the DEAF
Edgewood, Pennsylvania, 2015
7) Change the stroke on this to .001 inches or .072 pt to get ready to cut (hairline in Corel)
5
DIGITAL FABRICATION IN THE ARTS in the Cottage at the Western Pennsylvania School for the DEAF
Edgewood, Pennsylvania, 2015
8) Reselect the measurement and make the stroke 1 pt. Because this stroke is larger than .001 inches or .072 pt, the laser cutter will etch this and not cut.
6
DIGITAL FABRICATION IN THE ARTS in the Cottage at the Western Pennsylvania School for the DEAF
Edgewood, Pennsylvania, 2015
9) Save as to EPS
10) Move the file to the laser cutter computer via USB. 11) Import your file in CorelDraw
7
DIGITAL FABRICATION IN THE ARTS in the Cottage at the Western Pennsylvania School for the DEAF
Edgewood, Pennsylvania, 2015
If it shows you this window, please enter 1:1in the scaling.
8
DIGITAL FABRICATION IN THE ARTS in the Cottage at the Western Pennsylvania School for the DEAF
Edgewood, Pennsylvania, 2015
12) Make sure your numbers and measurements are still grouped
9
DIGITAL FABRICATION IN THE ARTS in the Cottage at the Western Pennsylvania School for the DEAF
Edgewood, Pennsylvania, 2015
13) and your cut lines are at hairline.
14) Save your file. 15) Go to File>Print>then click on Preferences
10
DIGITAL FABRICATION IN THE ARTS in the Cottage at the Western Pennsylvania School for the DEAF
Edgewood, Pennsylvania, 2015
16) You will see the Epilog Driver
17)
● Adjust the SPEED/POWER for Raster Engravings and SPEED/POWER/FREQ for Vector Cuts according to the Epilog Guide attached to the end of this booklet.
● ● Adjust the PIECE SIZE and make it the same size as the material you have in the
Laser Cutter ● ● Make sure AUTO FOCUS is checked ● ● Then press OK. ● ● Then from the PRINT DIALOG BOX, press OK again.
11
DIGITAL FABRICATION IN THE ARTS in the Cottage at the Western Pennsylvania School for the DEAF
Edgewood, Pennsylvania, 2015
18) You will see your file in the digital panel of the laser cutter.
19) Check to make sure the vent is on. 20) Then press GO. DO NOT LIFT THE COVER OF THE MACHINE WHILE YOU ARE CUTTING 21) Clean up after yourself and shut the machine off.
12
