c3 Controls Cbfs - Cbfsr

s e r i e s s e r i e s s e r i e s

o hazardous i

30mm 22mm 22mm

30

CERTIFICATIONSConformity to Standards: Certifications:UL 508, 698, 1604 and 2279 UL File #: 157436CSA C22.2 No. 25, 30M, 157 and 213 CSA File #: LR47446IEC 60947-5-1 CE Marked (per EU Low Voltage Directive 73/23/EEC)

Demko File #: 99Y9933270UATEX Certificate #04ATEX0409135U

ELECTRICAL RATINGSHermetically Sealed Refer to page 102.Factory Sealed Refer to page 103.

ENVIRONMENTAL RATINGAll c3controls 30mm H-Line products are UL Listed and are rated for Types 1, 2, 3, 3R, 4/4X, 12 and 13, and meet global standards requirements.

MECHANICAL DESIGN LIFE CYCLESPush Buttons Momentary: 5 Million

Maintained: 1 Million

Selector Switches Non-Illuminated: 3 Million

Standard Contact Blocks 5 Million

Pilot Lights Refer to the Lamp Technical Data charts on page 121.

TEMPERATURE RANGEStorage Temperature: -40 to +185° F (-40 to +85° C)Operating Temperature: -40 to +131° F (-40 to +55° C)

TERMINAL CAPACITY#6 Steel, Plated Terminal Screws with Self Lifting Captive Wire Clamps#22 to #12 AWG (0.5 - 4mm2) Wires (one or two wires per terminal)75° C Copper WireRecommended Terminal Tightening Torque: 7 lb-in (60 Nm).

T E C H N I C A L D A T A

Contact Blocks 102

Push Buttons 104

Pilot Lights 112

Selector Switches 116

Legend Plates 118

Accessories 120

Dimensions 122

See Enclosures 199

Turn to c3controls for30mm Industrial PilotDevices for your toughest

hazardous-duty applications, specially

designed for Class 1, Division 2,

Zone 2. Our 30mm H-Line includes

the broadest range of hermetically sealed

reed switches and factory sealed switches

from 2A to 10A. The 30mm H-Line features all-polyester construction for superior

durability, and every metal part is nickel-plated or stainless steel for superior corrosion

resistance. All operators are UL Listed and are rated Type 4/4X as standard for watertight

and corrosion resistance. In addition, operators are also listed for Type 1, 2, 3, 3R, 12 and

13, and meet global standards requirements.

www.c3controls.com BUY SMART BUY C3CONTROLS 1-800-560-8560 Fax 724-775-5283 101

s e r i e s s e r i e s s e r i e s s e r i e s

ordinary location hazardous iec nema

30mm 30mm 22mm 22mm

30 CONTACT BLOCKS | Modu lar

1. Thermoplastic Stroker

2. Solid Brass Bus Connection

3. Thermoplastic Polyester Body

4. Stainless Steel Terminal Screw

5. Hermetically Sealed Glass Chamber

6. Actuator Magnet

7. Silver Alloy Contacts

HE R M E T I C A L LY SE A L E D FE AT U R E S

www.c3controls.com BUY SMART BUY C3CONTROLS 1-800-560-8560 Fax 724-775-5283102

HERMETICALLY SEALED LOGIC REED CONTACT BLOCKCONFIGURATION - (40 WATTS RESISTIVE)

CODE CONTACT SYMBOL DESCRIPTION COLOR LISTLRNO 1 Normally Open Green $11.00

Contact BlockLRNC 1 Normally Closed Red $11.00

Contact Block(Class 1, Division 2-Zone 2) Logic Reed Blocks are Rated 220V Max.(Thermal), 2 Amps Max., 40 Watts Resistive Max.

• Logic Reeds are great for low power levels (resistive loads only),especially PLC inputs.

• Power Reeds are hermetically sealed, which is excellent for harsh environments and for 100% reliable operations.

HERMETICALLY SEALED MEDIUM LOGIC REEDCONTACT BLOCK CONFIGURATION -

(40 VA INDUCTIVE, 100 WATTS RESISTIVE)CODE CONTACT SYMBOL DESCRIPTION COLOR LISTMLRNO 1 Normally Open Green $18.00

Contact Block MLRNC 1 Normally Closed Red $18.00

Contact Block MLR2NO 2 Normally Open Green/Green $28.00

Contact Blocks MLR2NC 2 Normally Closed Red/Red $28.00

Contact Blocks MLRNONC 1 Normally Open Green/Red $28.00

and 1 Normally Closed Contact Blocks

(Class 1, Division 2-Zone 2) Medium Logic Reed Blocks are Rated 250V, 3.0 Amps Max. (Thermal), 40 VA Inductive Max.,100 Watts Resistive Max.

HERMETICALLY SEALED MID-POWER REED CONTACTBLOCK CONFIGURATION - (180 VA INDUCTIVE)

CODE CONTACT SYMBOL DESCRIPTION COLOR LISTMPRNO 1 Normally Open Green $30.00

Contact Block MPRNC 1 Normally Closed Red $30.00

Contact Block MPR2NO 2 Normally Open Green/Green $52.00

Contact Blocks MPR2NC 2 Normally Closed Red/Red $52.00

Contact Blocks MPRNONC 1 Normally Open Green/Red $52.00


(Class 1, Division 2-Zone 2) Mid-Power Reed MPRNO Series C300AC, 240V AC Max., 2.5 Amps Continuous Thermal, 1800 VA (Make)180 VA (Break), Q150 DC, 69 VA Make and Break, 125V DC Max.,2.5 Amps Continuous Thermal.

HERMETICALLY SEALED POWER REED CONTACT BLOCKCONFIGURATION - (360 VA INDUCTIVE)

CODE CONTACT SYMBOL DESCRIPTION COLOR LISTPRNO 1 Normally Open Green $38.00

Contact Block PRNC 1 Normally Closed Red $38.00

Contact Block PR2NO 2 Normally Open Green/Green $60.00

Contact Blocks PR2NC 2 Normally Closed Red/Red $60.00

Contact Blocks PRNONC 1 Normally Open Green/Red $60.00


Class 1, Division 2 (Groups A,B,C,D) - Zone 2 (Groups IIc) Rated B300,240V AC, 5 Amps (Thermal) Continuous, 3600 VA Make, 360 VA Break(AC), C600 AC, Q300 DC, 220V DC, 69 VA Make and Break (DC).

DISCOUNTSCHEDULE A

6

2

7

5

14

3

FA C T O RY SE A L E D FE AT U R E S1. Glass Reinforced Thermoplastic Body

2. Fine Silver Contacts

3. Stainless Steel Bushing

4. Stainless Steel Terminal Screw

5. Stainless Steel Shaft

6. Nickel-Plated Terminals

7. Stainless Steel Overtravel Spring

8. Stainless Steel Kickout Spring

Modu lar CONTACT BLOCKSs e r i e s s e r i e s s e r i e s s e r i e s


30mm 30mm 22mm 22mm

30


30M M H-LI N E CO N TA C T BL O C K SOur H-Line Contact Blocks feature convenient snap-on secured assembly, saving valuable time and money. For added security, all H-Line operators come standard with a screw-tightening mounting bracket to ensure the contact blocks remain snug to the operator. The hermetically sealed and factory sealed contact blocks are manufactured with all stainless steel hardware, which is excellent for harsh environments and for 100% reliability. We also offer ordinary location contact blocks, please refer to pages 70-71 in our 30mm section.

Mid-Power Reed Medium Logic Reed

AVA I L A B L E CO N TA C T BL O C K S F O R H-LI N E LO C AT I O N S

FACTORY SEALED CONTACT BLOCK CONFIGURATION(720 VA)

CODE CONTACT SYMBOL DESCRIPTION LISTCBFS 1 Normally Open and $48.00

1 Normally Closed Contact Blocks (to be used with linear devices)

CBFSR 1 Normally Open and $48.001 Normally Closed Contact Blocks (to be used with rotary selector devices)

Class 1, Division 2 (Groups B,C,D) T6 (85°C) - Zone 2, A600 RatingDesignation, 10A Continuous @ 600V AC (Thermal), 7200 VA (Make),720 VA (Break). Q300 DC, 250V DC Max., 69 VA Make and Break.

Factory Sealed forLinear Devices

Power Reed Logic ReedFactory Sealed ForRotary Devices

DISCOUNTSCHEDULE A

1

2

3

4

56

7

8

Modu lar | CONTACT BLOCKS



30mm 30mm 22mm 22mm

30

S P E C I A L F E A T U R E

Your Secondary Defense for Added Protection.Chemicals on gloves, wash down areas and particularly harshclimates will do damage to any push button. Utilizing ourstate-of-the-art rubber boots protect both the operators and

the circuits behind them.

Our Fluorosilicone Rubber Boots feature a nickel-plated brassthreaded ring that is insert molded into a special thermoset compoundto withstand most applications in corrosive environments and perform well against more chemicals and vapors than Hypalon Boots.

Standard Rubber Boots are also available. See page 72.

PUSH BUTTONS | Momentary Non - I l l um inated


I T ’ S E A S Y T O B U I L D Y O U R O W N P U S H B U T T O NSimply pick the code number from each of the sections below and combine them to build your partnumber. See page 4 for more detailed directions.

Momentary Push Buttons (Non-Illuminated)

I II III IV V

Example: To build one of our most popular Push Buttons, the part number would be I + II + III + IV + Vor HPBO-FCGN-PRNO

III. CAP TYPECODE DESCRIPTION LISTFC Flush Cap $ 2.40GFC Guarded Flush Cap $ 5.40XC Extended Cap $ 2.40GXC Guarded Extended Cap $ 5.40MC Mushroom Cap $ 8.00JMC Jumbo Mushroom Cap $10.00SMC Shrouded Mushroom Cap $12.50SJC Shrouded Jumbo $14.50

Mushroom Cap

II. CLAMP RINGCODE DESCRIPTION LIST(Blank) Polyester (Type 4X) —A Aluminum (Type 4)* $2.00

*NOTE: Aluminum clamp rings are NOT *corrosion resistant.

I. OPERATOR TYPECODE DESCRIPTION LISTHPBO Push Button Operator w/bracket $9.40PBO Push Button Operator* $8.40

IV. CAP COLORCODE COLOR(Blank) Operator less CapBK BlackBE BlueGN GreenGY GreyRD RedWE WhiteYW Yellow

L E G E N DP L A T E S inalmost any size &color are available

for same day shipping.See pages 118-119 for complete selection.

Example: To build one of our most popular PushButtons with a Rubber Boot, replace II, III & IV(Clamp Ring, Cap Type & Color) with the codefrom the rubber boot chart above. The part number would be I + (code from rubber boot chart above) + V or HPBO-HRBGN-CBFS.NOTE: Rubber boots come standard with a built-in clamp ring andthrust washer. When installing operator we recommend that thethrust washer be placed behind the panel to prevent rotation.

RUBBER BOOTS ALSO AVAILABLE

DISCOUNTSCHEDULE A

V. CONTACT BLOCK CONFIGURATIONCODE DESCRIPTION LIST

FACTORY SEALED, CLASS 1, DIV. 2/ZONE 2, 720 VA(Blank) Operator without Contact Blocks —CBFS Contact Block with 1 Normally $48.00

Open/1 Normally Closed POWER REED, CLASS 1, DIV. 2/ZONE 2, 360 VA INDUCTIVE(Blank) Operator without Contact Blocks —PRNO 1 Normally Open Contact Block $38.00PRNC 1 Normally Closed Contact Block $38.00PR2NO Contact Block w/2 Normally Open $60.00PR2NC Contact Block w/2 Normally Closed $60.00PRNONC Contact Block with 1 Normally $60.00

Open/1 Normally Closed MID-POWER REED, CLASS 1, DIV. 2/ZONE 2, 180 VA INDUCTIVE(Blank) Operator without Contact Blocks —MPRNO 1 Normally Open Contact Block $30.00MPRNC 1 Normally Closed Contact Block $30.00MPR2NO Contact Block w/2 Normally Open $52.00MPR2NC Contact Block w/2 Normally Closed $52.00MPRNONC Contact Block with 1 Normally $52.00

Open/1 Normally Closed MEDIUM LOGIC REED, CLASS 1, DIV. 2/ZONE 2,

40 VA INDUCTIVE, 100 WATTS RESISTIVE(Blank) Operator without Contact Blocks —MLRNO 1 Normally Open Contact Block $18.00MLRNC 1 Normally Closed Contact Block $18.00MLR2NO Contact Block w/2 Normally Open $28.00MLR2NC Contact Block w/2 Normally Closed $28.00MLRNONC Contact Block with 1 Normally $28.00

Open/1 Normally Closed LOGIC REED, CLASS 1, DIV. 2/ZONE 2, 40 WATTS RESISTIVE*

(Blank) Operator without Contact Blocks —LRNO 1 Normally Open Contact Block $11.00LRNC 1 Normally Closed Contact Block $11.00*NOTE: Logic Reeds do not require and are not providedwith a Mounting Screw and must be used with a PBO.

FLUOROSILICONE RUBBER BOOTSCODE COLOR LISTHRBBK Black $18.00HRBGN Green $18.00HRBRD Red $18.00HRBYW Yellow $18.00

*NOTE: PBO can only be used with a Logic Reed contact block.



30mm 30mm 22mm 22mm

30Momentary Non - I l l um inated | PUSH BUTTONS


30M M H-LI N E MO M E N TA RYNO N-IL L U M I N AT E D PU S H BU T T O N Sc3controls goes the extra step to make sure that our products outlast the competition. Our 30mm H-Line Momentary Non-Illuminated Push Buttons are durable and flexible for a variety of uses, and allmetal parts are nickel-plated for superior corrosion resistance. All c3controls 30mm H-Line operatorsare UL Listed and are rated Type 4/4X standard for watertight and corrosion resistance. In addition,operators are also listed for Type 1, 2, 3, 3R, 12 and 13, and meet global standards requirements.

Product features include:

• Polyester construction for superior corrosion resistance, moisture rejection and electrical insulation.

• Our 30mm H-Line operators come standard with a polyester clamp ring, although optional aluminum clamp rings are available.

• #6 stainless steel terminal screws with self-lifting captive wire clamps accommodate #22 through two#12 AWG wires (0.5 - 4mm2) per terminal.

• Operators conveniently mount in a round 1-13/64” (30.5mm) hole that is directly interchangeablewith competitors units and eliminate the labor required for notching.

MOMENTARY NON-ILLUMINATED PUSH BUTTON OPERATORSWITH POLYESTER CLAMP RING (TYPE 4X)

FLUSH CAP EXTENDED CAPCAP COLOR CATALOG NUMBER LIST CATALOG NUMBER LISTGreen HPBO-FCGN-PRNO $49.80 HPBO-XCGN-PRNO $49.80Red HPBO-FCRD-PRNC $49.80 HPBO-XCRD-PRNC $49.80Green HPBO-FCGN-CBFS $59.80 HPBO-XCGN-CBFS $59.80Red HPBO-FCRD-CBFS $59.80 HPBO-XCRD-CBFS $59.80

SOME OF OUR POPULAR CONFIGURATIONS:

U N I Q U E P R O D U C T F E A T U R E S

1. Our revolutionary U-Cup seal is infused with a Teflon coating to eliminate cracking when exposedto harsh conditions such as heat, dryness and sunlight. The U-Cup seal rides easily along thestroker and keeps water, oils, dust and other corrosive particles in the air away from the contactblocks. This U-cup seal also acts like a squeegee and forms a permanent watertight seal thatmeets Type 4/4X with or without a rubber boot. In fact, our push button was the first to be ratedType 4X without using a rubber boot!

2. Our push buttons modular design provides endless options for appropriate operator interface by alternating cap types and colors which ultimately will save you time and money by reducing your inventory.

ADDED SECURITY!For added security, all H-LinePush Buttons come standard with a screw tightening mountingbracket to ensure the contact

blocks remain snug to the operator.

Extended Cap Mushroom Cap (1.5” (38mm) dia.)

Jumbo Mushroom Cap

(2.25” (57mm) dia.)

Shrouded Mushroom Cap

(1.5” (38mm) dia.)

Shrouded JumboMushroom Cap

(2.25” (57mm) dia.)

Flush Cap Guarded Flush Cap

GuardedExtended Flush Cap

MIX AND MATCH ANY COLOR AND MOMENTARY NON-ILLUMINATED PUSH BUTTON CAP

105

PUSH BUTTONS Mainta ined Non - I l l um inated s e r i e s s e r i e s s e r i e s s e r i e s


30mm 30mm 22mm 22mm

30 PUSH BUTTONS | Mainta ined Non - I l l um inated

106 www.c3controls.com BUY SMART BUY C3CONTROLS 1-800-560-8560 Fax 724-775-5283

I T ’ S E A S Y T O B U I L D Y O U R O W N P U S H B U T T O NSimply pick the code number from each of the sections belowand combine them to build your part number. See page 4 formore detailed directions.

VI. CONTACT BLOCK CONFIGURATION(USE CHART V FROM ABOVE)

Example: To build one of our mostpopular Push Buttons, the part number would be I + II + TMC + IV + Vor HPTR -TMCRD-CBFS

Maintained Push Buttons (Non-Illuminated)2-Position Push-Twist Release

TMCI II III IV V

III. CAP TYPECODE DESCRIPTION LISTTMC Twist Mushroom Cap $8.00

IV. CAP COLORCODE COLORBK BlackBE BlueGN GreenGY GreyRD RedWE WhiteYW Yellow

IV. CAP TYPECODE DESCRIPTION LISTMC Mushroom Cap —JMC Jumbo Mushroom Cap $4.00

V. CAP COLORCODE COLOR(Blank) Operator less CapBK BlackBE BlueGN GreenGY GreyRD RedWE WhiteYW Yellow

I. OPERATOR TYPECODE DESCRIPTION LISTHPTR Push-Twist Release w/bracket $31.00PTR Push-Twist Release* $30.00*NOTE: PTR can only be used with a Logic Reed CB.

II. CLAMP RINGCODE DESCRIPTION LIST(Blank) Polyester (Type 4X) —A Aluminum (Type 4)* $2.00*NOTE: Aluminum clamp rings are NOT corrosion resistant.

I. OPERATOR TYPECODE DESCRIPTION LISTHPBO Push Button Operator w/bracket $9.40PBO Push Button Operator* $8.40*NOTE: PBO can only be used with a Logic Reed CB.


*NOTE: Aluminum clamp rings are NOTcorrosion resistant.

Example: To build one of our most popular Push Buttons, the part numberwould be I + II + III + IV + V + VIor HPBO-HPPMCRD-PRNONC

Maintained Push Buttons (Non-Illuminated)2-Position Push-Pull

I II III IV V VI

III. CAP FUNCTIONCODE DESCRIPTION LISTHPP Stainless Steel Push-Pull Maint. $40.60PP Brass Push-Pull Maint. $26.60

The linear push-off twist to release style operator requires a “twist” for the “out” or “on”position and a linear “push” for the “in” or “off”position. The twist mushroom cap is marked witharrows identifying the direction for the twist release.

The 2-Position Push-Pull is maintained in both the push and pull positions. The primary application is “push” to “stop” and “pull” to “start”.

V. CONTACT BLOCK CONFIGURATIONCODE DESCRIPTION LIST







(Blank) Operator without Contact Blocks —LRNO 1 Normally Open Contact Block $11.00LRNC 1 Normally Closed Contact Block $11.00

*NOTE: Logic Reeds do not require and are not *provided with a Mounting Screw and must be*used with a PTR or PBO.

DISCOUNTSCHEDULE A



30mm 30mm 22mm 22mm

30Mainta ined Non - I l l um inated | PUSH BUTTONS

2-POSITION PUSH-PULL MAINTAINED OPERATORSMAINTAINED IN/MAINTAINED OUT

POWER REED CONTACT BLOCK FACTORY SEALED CONTACT BLOCK2 CIRCUIT (1 NO/1 NC) 2 CIRCUIT (1 NO/1 NC)

OUT IN OUT INNC X O NC X ONO O X NO O X

CAP COLOR CATALOG NUMBER LIST CATALOG NUMBER LISTBlack HPBO-HPPMCBK-PRNONC $110.00 HPBO-HPPMCBK-CBFS $98.00Green HPBO-HPPMCGN-PRNONC $110.00 HPBO-HPPMCGN-CBFS $98.00Red HPBO-HPPMCRD-PRNONC $110.00 HPBO-HPPMCRD-CBFS $98.00Yellow HPBO-HPPMCYW-PRNONC $110.00 HPBO-HPPMCYW-CBFS $98.00


30M M H-LI N E MA I N TA I N E DNO N-IL L U M I N AT E D PU S H BU T T O N STHE MOST RUGGED EMERGENCY STOP AVAILABLE IN THE INDUSTRY!The 30mm H-Line of maintained non-illuminated push buttons feature all polyester construction and all metal parts are nickel-plated for superior corrosion resistance; #6 stainless steel terminal screws have self-lifting captive wire clamps to accommodate #22 through two #12 AWG wires (0.5 - 4mm2) per terminal. Units mount in a round 1-13/64” (30.5mm) hole and are directly interchangeable with competitors units. Operators are UL Listed and are rated Type 4/4X standard for watertight and corrosion resistance. In addition, operators are also listed for Type 1, 2, 3, 3R, 12 and 13, and meet global standards requirements.

SOME OF OUR POPULAR CONFIGURATIONS:2-POSITION PUSH-TWIST RELEASE OPERATORS

MAINTAINED IN/MAINTAINED OUTPOWER REED CONTACT BLOCK FACTORY SEALED CONTACT BLOCK2 CIRCUIT (1 NO/1 NC) 2 CIRCUIT (1 NO/1 NC)

OUT IN OUT INNC X O NC X ONO O X NO O X

CAP COLOR CATALOG NUMBER LIST CATALOG NUMBER LISTBlack HPTR-TMCBK-PRNONC $99.00 HPTR-TMCBK-CBFS $87.00Green HPTR-TMCGN-PRNONC $99.00 HPTR-TMCGN-CBFS $87.00Red HPTR-TMCRD-PRNONC $99.00 HPTR-TMCRD-CBFS $87.00Yellow HPTR-TMCYW-PRNONC $99.00 HPTR-TMCYW-CBFS $87.00

AVAILABLE CAP COLORS FOR 2-POSITION MAINTAINED NON-ILLUMINATED PUSH BUTTONS

Mushroom Cap(1.5” (38mm) dia.)

Jumbo Mushroom Cap(2.25” (57mm) dia.)

Mushroom Cap(1.5” (38mm) dia.)


U N I Q U E F E A T U R E S

Our push-twist operator features a nickel-plated detent mechanism with stainless steel ball while our push-pull operator contains a solid stainless steel detent mechanism.These are the best-engineered, most reliable heavy-duty emergency stop buttons in the world. This rugged design,which comes standard with a polyester clamp ring or optionalaluminum clamp ring, ensures reliable operation in emergency applications, providing safe interruption of circuits, and much longer life when compared to any competitor’s product.

We Put The Metal On The Inside —Where It Counts!

Twist Mushroom Cap(1.5” (38mm) dia.)

Twist Mushroom Cap(1.5” (38mm) dia.)


O = OPENX = CLOSED

O = OPENX = CLOSED

ADDED SECURITY!For added security, all H-LinePush Buttons come standard with a screw tightening mountingbracket to ensure the contact

blocks remain snug to the operator.

107



30mm 30mm 22mm 22mm

30 PUSH BUTTONS | Momentary I l l um inated


I T ’ S E A S Y T O B U I L D Y O U R O W N P U S H B U T T O NSimply pick the code number from each of the sections below and combinethem to build your part number. See page 4 for more detailed directions.

Example: To build one of our most popular Push Buttons,the part number would be I + II + III + IV + V + VI + VII or HFVLU120-H IPBCGN-PRNO

Momentary Push Buttons (Illuminated)*

I II III IV V VI VII

VI. LENS COLORCODE COLORAR AmberBE BlueCR ClearGN GreenRD RedWE WhiteYW Yellow

I. BASIC ILLUMINATED PUSHBUTTON OPERATOR

CODE DESCRIPTION LISTHFVLU Full Voltage $31.00HTFLU Transformer (50/60 Hz) $40.00HRLU Resistor $31.00HRTLU Dual Input Remote Test $49.00

II. VOLTAGE BASED ON OPERATOR TYPE

CODE DESCRIPTIONFULL VOLTAGE

6 6V AC/DC12 12V AC/DC24 24V AC/DC120 120V AC/DC

TRANSFORMER120 120V AC240 240V AC277 277V AC480 480V AC

RESISTOR120 120V AC/DC240 240V AC/DC480 480V AC/DC

DUAL INPUT REMOTE TEST6 6V AC/DC12 12V AC/DC24 24V AC/DC120 120V AC/DC

III. LAMP TYPE/COLORCODE COLOR LIST

LEDLA Amber $10.00LB Blue $10.00LG Green $10.00LR Red $10.00LW White $10.00

INCANDESCENT(Blank) Clear —F Clear Flashing Bulb* $ 4.00

*NOTE: Incandescent flashing bulbs available for any 6V full voltage or transformer application.

NEON†NG Green —NR Red —

†NOTE: Only Available in HFVLU120,HRLU240 and HRLU480.

NL No Lamp – $ 1.00

IV. CLAMP RINGCODE DESCRIPTION LIST(Blank) Polyester (Type 4X) —A Aluminum (Type 4)* $2.00*NOTE: Aluminum clamp rings are NOT corrosion resistant.

SE E PAGE 121 F O R LAMPTE C H N I C A L DATA AND LAMPRE P L A C E M E N TCHAR TS .

VII. CONTACT BLOCK CONFIGURATIONCODE DESCRIPTION LIST







(Blank) Operator without Contact Blocks —LRNO 1 Normally Open Contact Block $11.00LRNC 1 Normally Closed Contact Block $11.00*NOTE: Logic Reeds do not require and are not provided*with a Mounting Screw.

DISCOUNTSCHEDULE A

*NOTE: Our momentary illuminated push buttons must be ordered as an assembled part. Contact blocks may be ordered separately.

V. LENS TYPECODE DESCRIPTION LISTHIPBC Illuminated Push Button Lens $ 8.00HIPBCM Illuminated Push Button $12.00

Mushroom Lens HGIPBC Guarded Illuminated $12.00

Push Button Lens*HSIPBCM Shrouded Illuminated $16.00

Push Button Mushroom Lens**NOTE: Aluminum clamp rings are not an option for

HGIPBC or HSIPBCM.

NOTE: When specifying a Logic Reed (LRNO, LRNC) from Chart VII, delete the “H” from the Lens Type code above.

Our unique Dual Input Remote lightunit can be used as an illuminated pushbutton while also permitting the testingof a number of lights from a single pushbutton. A diode circuit isolates the testsupply from the normal supply. Theschematic shownrepresents a typical dual input application.

TEST L1 1LS 1CR L2

COMMON

NORMAL

3CR PSTEST

NORMAL

TEST

COMMON

COMMON

NORMAL

TEST

SOL2LS

D U A L I N P U TR E M O T E T E S T

MOMENTARY ILLUMINATED PUSH BUTTON OPERATORS WITH POLYESTER CLAMP RING (TYPE 4X)

PUSH BUTTON LENS MUSHROOM LENSLENS COLOR CATALOG NUMBER LIST CATALOG NUMBER LIST

Full Amber HFVLU120-HIPBCAR-PRNONC $99.00 HFVLU120-HIPBCMAR-PRNONC $103.00Voltage Green HFVLU120-HIPBCGN-PRNO $77.00 HFVLU120-HIPBCMGN-PRNO $81.00

Red HFVLU120-HIPBCRD-PRNC $77.00 HFVLU120-HIPBCMRD-PRNC $81.00Trans- Amber HTFLU120-HIPBCAR-PRNONC $108.00 HTFLU120-HIPBCMAR-PRNONC $112.00former Green HTFLU120-HIPBCGN-PRNO $86.00 HTFLU120-HIPBCMGN-PRNO $90.00

Red HTFLU120-HIPBCRD-PRNC $86.00 HTFLU120-HIPBCMRD-PRNC $90.00Resistor Green HRLU120-HIPBCGN-PRNO $77.00 HRLU120-HIPBCMGN-PRNO $81.00

Red HRLU120-HIPBCRD-PRNC $77.00 HRLU120-HIPBCMRD-PRNC $81.00


Momentary I l l um inated PUSH BUTTONSs e r i e s s e r i e s s e r i e s s e r i e s


30mm 30mm 22mm 22mm

30Momentary I l l um inated | PUSH BUTTONS


30M M H-LI N E MO M E N TA RYIL L U M I N AT E D PU S H BU T T O N Sc3controls 30mm H-Line Momentary Illuminated Push Buttons are durable and flexible for a variety of uses, and all metal parts are nickel-plated for superior corrosion resistance. All c3controls 30mm H-Line operators are UL Listed and are rated Type 4/4X standard for watertight and corrosion resistance. In addition, operators are also listed for Type 1, 2, 3, 3R, 12 and 13, and meet global standards requirements.




• Full voltage lights incorporate a unique insulated socket design to minimize accidental contact during lamp change.

• All lights use miniature bayonet base lamps that are nickel-plated for corrosion-resistance and to provide reliable lamp secureness.

• #6 stainless steel terminal screws with self-lifting captive wire clamps accommodate #22 through two #12 AWG wires (0.5 - 4mm2) per terminal.

• Operators conveniently mount in a round 1-13/64” (30.5mm) hole that is directly interchangeable with competitors units and eliminate the labor required for notching.


1. Our revolutionary U-Cup seal is infused with a Teflon coating to eliminate crackingwhen exposed to harsh conditions such as heat, dryness and sunlight. The U-Cup sealrides easily along the stroker and keeps water, oils, dust and other corrosive particles inthe air away from the contact blocks. This U-cup seal also acts like a squeegee and formsa permanent watertight seal that meets Type 4/4X standards.

2. All frictional parts are molded with an internal self lubricant to provide outstanding wear withouttroublesome greases used by others.

ADDED SECURITY!For added security, all H-Line Push Buttons comestandard with ascrew tighteningmounting bracket toensure the contactblocks remain snug tothe operator.

MI X A N D MAT C H AN Y CO L O R A N D MO M E N TA RY IL L U M I N AT E D PU S H BU T T O N LE N S

Push Button Lens Push Button Lens Guarded PushButton Lens

Push Button Lens Mushroom Lens (1.5” (38mm) dia.)

Shrouded Mushroom Lens

(1.5” (38mm) dia.)

Mushroom Lens (1.5” (38mm) dia.)



30mm 30mm 22mm 22mm

30 PUSH BUTTONS | Mainta ined I l l um inated


I T ’ S E A S Y T O B U I L D Y O U R O W N P U S H B U T T O NSimply pick the code number from each of the sections below and combinethem to build your part number. See page 4 for more detailed directions.

Example: To build one of our most popular Push Buttons, thepart number would be I + PPM + III + IV + V + IMC + VII + VIIIor HFVPPM120- IMCAR-PRNONC

Maintained Push Buttons (Illuminated)2-Position Push-Pull

PPM IMC I II III IV V VI VII VIII

I. BASIC ILLUMINATED PUSHBUTTON OPERATOR

CODE DESCRIPTION LISTHFV Full Voltage $43.00HTF Transformer (50/60 Hz) $58.00HRL Resistor $45.00

II. CAP TYPECODE DESCRIPTIONPPM Push-Pull Maintained

VI. LENS TYPECODE DESCRIPTION LISTIMC Illuminated Push Button $12.00

Mushroom Lens

VII. LENS COLORCODE COLORAR AmberBE BlueCR ClearGN GreenRD RedWE White

The 2-Position Push-Pull is maintainedin both the push and pull positions. The primary application is “push” to“stop” and “pull” to “start”.

III. VOLTAGE BASED ON OPERATOR TYPE





IV. LAMP TYPE/COLORCODE COLOR LIST





†NOTE: Only Available in HFVPPM120, HRLPPM240 and HRLPPM480.


V. CLAMP RINGCODE DESCRIPTION LIST(Blank) Polyester (Type 4X) —A Aluminum (Type 4)* $2.00

*NOTE: Aluminum clamp ringsare NOT corrosion resistant.

VIII. CONTACT BLOCK CONFIGURATIONCODE DESCRIPTION LIST







(Blank) Operator without Contact Blocks —LRNO 1 Normally Open Contact Block $11.00LRNC 1 Normally Closed Contact Block $11.00*NOTE: Logic Reeds do not require and are not provided*with a Mounting Screw.

DISCOUNTSCHEDULE A

SE E PAGE 121 F O R LAMPTE C H N I C A L DATA AND LAMPRE P L A C E M E N T CHAR TS .

Mainta ined I l l um inated | PUSH BUTTONSs e r i e s s e r i e s s e r i e s s e r i e s


30mm 30mm 22mm 22mm

30



2-POSITION PUSH-PULL MAINTAINED OPERATORS WITH POLYESTER CLAMP RING (TYPE 4X)POWER REED CONTACT BLOCK FACTORY SEALED CONTACT BLOCK

2 CIRCUIT (1 NO/1 NC) 2 CIRCUIT (1 NO/1 NC)

OUT IN OUT INPRNONC X O CBFS X OPRNONC O X CBFS O X

TYPE CATALOG NUMBER LIST CATALOG NUMBER LISTTransformer HTFPPM120-IMCRD-PRNONC $130.00 HTFPPM120-IMCRD-CBFS $118.00Full Voltage HFVPPM120-LRIMCRD-PRNONC $125.00 HFVPPM120-LRIMCRD-CBFS $113.00Resistor HRLPPM120-IMCRD-PRNONC $117.00 HRLPPM120-IMCRD-CBFS $105.00

AVA I L A B L E LE N S CO L O R S F O R 2-PO S I T I O N MA I N TA I N E D IL L U M I N AT E D PU S H BU T T O N S

30M M H-LI N E MA I N TA I N E DIL L U M I N AT E D PU S H BU T T O N Sc3controls 30mm H-Line Maintained Illuminated Push Buttons are durable and flexible for a variety of uses, and all metal parts are nickel-plated for superior corrosion resistance. All c3controls 30mm H-Line operators are UL Listed and are rated Type 4/4X standard for watertight and corrosion resistance. In addition,operators are also listed for Type 1, 2, 3, 3R, 12 and 13, and meet global standardsrequirements.





• All lights use miniature bayonet base lamps that are nickel-plated for corrosion-resistance and provide reliable lamp secureness.


• Operators conveniently mount in a round 1-13/64” (30.5mm) hole that is directly interchangeable with competitors units and eliminate the labor required for notching.


(1.5” (38mm) dia.)(1.5” (38mm) dia.) (1.5” (38mm) dia.)(1.5” (38mm) dia.) (1.5” (38mm) dia.)(1.5” (38mm) dia.)

O = OPENX = CLOSED

1. Our seal is infused with a coating to eliminate cracking when exposed to harsh conditions such as heat, dryness and sunlight. This seal also acts as a light reflector because it is white which increases light output and improves visibility from all angles.

2. All frictional parts are molded with an internal self lubricant to provide outstanding wear without troublesome greases used by others.

3. Our rugged Lexan™ caps can resist high impact for reliable performance in most environments even in high temperature ambients.

111

Pilot LightsPLL

I II III IV V VI



30mm 30mm 22mm 22mm

30 PILOT L IGHTS |


I T ’ S E A S Y T O B U I L D Y O U R O W N P I L O T L I G H TSimply pick the code number from each of the sections below and combinethem to build your part number. See page 4 for more detailed directions.

Example: To build one of our most popular Pilot Lights, the part number would be I + II + III + IV + PLL + VI or HFVLU120LG-PLLGN

VI. LENS COLORCODE COLORAR AmberBE BlueCR ClearGN GreenRD RedWE White

V. LENS TYPECODE DESCRIPTION LISTPLL Pilot Light Lens $6.00

II. VOLTAGE BASED ON OPERATOR TYPE





DUAL INPUT REMOTE TEST6 6V AC/DC12 12V AC/DC24 24V AC/DC120 120V AC/DC240 240V AC/DC

I. BASIC PILOT LIGHT OPERATORCODE DESCRIPTION LISTHFVLU Full Voltage $31.00HTFLU Transformer (50/60 Hz) $40.00HRLU Resistor $31.00HRTLU Dual Input Remote Test $49.00

III. LAMP TYPE/COLORCODE COLOR LIST





†NOTE: Only Available in HFVLU120, HRLU240 and HRLU480.


IV. CLAMP RINGCODE DESCRIPTION LIST(Blank) Polyester (Type 4X) —A Aluminum (Type 4)* $2.00


AVA I L A B L E LE N S CO L O R S F O R PI L O T LI G H T S


D U A L I N P U T R E M O T E T E S TOur unique Dual Input Remote light unit can be used as a pilot light while also permitting thetesting of a number of lights from a single pushbutton. A diode circuit isolates the test supplyfrom the normal supply. The schematic shownrepresents a typical dual input application.

TEST L1 1LS 1CR L2

COMMON

NORMAL

3CR PSTEST

NORMAL

TEST

COMMON

COMMON

NORMAL

TEST

SOL2LS

DISCOUNTSCHEDULE A



30mm 30mm 22mm 22mm

30| PILOT L IGHTS


30M M H-LI N E PI L O T LI G H T SOur 30mm H-Line Pilot Lights and Illuminated Push-To-Test PilotLights, when utilized with our LED lamps provide leakage protection, long-lasting life and high quality with tremendousresistance to shock and vibration. Our reflection technologyand state-of-the-art LED lamps improve visibility from allangles. c3controls LED lamps last 100,000 hours — that’s 11.4years! Combine these LEDs with our full voltage, transformer orresistor packages for optimum durability. All c3controls 30mmH-Line operators are UL Listed and are rated Type 4/4X standard for watertight andcorrosion resistance. In addition, operators are also listed for Type 1, 2, 3, 3R, 12 and 13, and meet global standards requirements.



• All metal parts are nickel-plated for superior corrosion resistance.



• Operators conveniently mount in a round 1-13/64” (30.5mm) hole that is directly interchangeable with competitors units and eliminates the labor required for notching.

PILOT LIGHTS WITH POLYESTER CLAMP RING (TYPE 4X)CATALOG NUMBER DESCRIPTION LISTHFVLU24LA-PLLAR Full Voltage 24V Amber LED w/Amber Lens $47.00HFVLU24LG-PLLGN Full Voltage 24V Green LED w/Green Lens $47.00HTFLU120LR-PLLRD Transformer 120V Red LED w/Red Lens $56.00


1. Compact, thin design is also vibration resistant.

2. Our seal is infused with a coating to eliminate cracking when exposed to harsh conditions such as heat, dryness and sunlight. This seal also acts as a light reflector because it is white which increases light output and improves visibility from all angles.

3. Our rugged Lexan™ lenses provide better visibility and can resist high impact for reliable performance in most environments, even in high temperature ambients.

4. These light units use a miniature bayonet base lamp which are nickel-plated for corrosion resistance and provide reliable lamp secureness.


113



30mm 30mm 22mm 22mm

30

SE E B O T T O M O F PA G E 109 F O R LE N S TY P E/CO L O R OP T I O N S.

I T ’ S E A S Y T O B U I L D Y O U R O W N P I L O T L I G H TSimply pick the code number from each of the sections below and combinethem to build your part number. See page 4 for more detailed directions.

PILOT L IGHTS | Push -To -Test


II. BASIC PUSH-TO-TEST OPERATOR CODE DESCRIPTION LISTFV Full Voltage $31.00TF Transformer (50/60 Hz) $40.00RL Resistor $31.00 VIII. LENS COLOR

CODE COLORAR AmberBE BlueCR ClearGN GreenRD RedWE White

V. LAMP TYPE/COLORCODE COLOR LIST





†NOTE: Only Available in FVPTT120, RLPTT240 and RLPTT480.


III. OPERATOR TYPECODE DESCRIPTION LISTPTT Push-To-Test $6.00

I. CONTACT BLOCK CONFIGURATIONCODE DESCRIPTION LISTHPR Hermetically Sealed Reed $60.00

Contact (wired at factory)HFS Factory Sealed Contact $54.00

(wired at factory)

IV. VOLTAGE BASED ON OPERATOR TYPE





VI. CLAMP RINGCODE DESCRIPTION LIST(Blank) Polyester (Type 4X) —A Aluminum (Type 4)* $2.00

*NOTE: Aluminum clamp rings*are NOT corrosion resistant.

Example: To build one of our most popular Pilot Lights, the part number would be I + II + PTT + IV + V + VI + VII + VIIIor HFSFVPTT120-H IPBCGN

Push-To-Test Pilot Lights combine an illuminated push button with a normallyopen/normally closed contact block factorywired for three-point wiring in standard push-to-test circuits. See page 86 forwiring schematic.

Push-To-Test Pilot LightsPTT

I II III IV V VI VII VIII


DISCOUNTSCHEDULE A

PUSH-TO-TEST PILOT LIGHTS W/POLYESTER CLAMP RING (TYPE 4X)CATALOG NUMBER DESCRIPTION LISTHPRFVPTT120-HIPBCAR FV 120V w/Incand. Lamp, Amber Lens & Herm. Seal. Reed $105.00HFSFVPTT120-HIPBCGN FV 120V w/Incand. Lamp, Green Lens & Factory Seal. CB $ 99.00HFSFVPTT120-HIPBCRD FV 120V w/Incand. Lamp, Red Lens & Factory Seal. CB $ 99.00

SOME OF OUR POPULAR CONFIGURATIONS:ADDED SECURITY!For added security, all H-Line Push-To-Test Pilot Lights come standard with a screw tightening

mounting bracket to ensure the contact blocks remain snug to

the operator.

VII. LENS TYPECODE DESCRIPTION LISTHIPBC Illuminated Push Button Lens $ 8.00HIPBCM Illuminated Push Button $12.00

Mushroom Lens HGIPBC Guarded Illuminated $12.00

Push Button Lens*HSIPBCM Shrouded Illuminated $16.00

Push Button Mushroom Lens**NOTE: Aluminum clamp rings are not an option for *HGIPBC or HSIPBCM.

AVA I L A B L E LE N S CO L O R S F O R MU LT I-VO LTA G E PI L O T LI G H T S

Mult i -Vo l tage | PILOT L IGHTSs e r i e s s e r i e s s e r i e s s e r i e s


30mm 30mm 22mm 22mm

30


I T ’ S E A S Y T O B U I L D Y O U R O W N P I L O T L I G H T

20-240 Multi-Voltage Pilot Lights30MV20-240 LW PLL

I II III IV V VI

VI. LENS COLORCODE COLORAR AmberBE BlueCR ClearGN GreenRD RedWE White

IV. CLAMP RINGCODE DESCRIPTION LIST(Blank) Polyester (Type 4X) —A Aluminum (Type 4)* $2.00


II. LED BULB FUNCTIONCODE DESCRIPTION LISTD Standard —F Flashing $10.00

Simply pick the code number from each of the sections below and combinethem to build your part number. See page 4 for more detailed directions.

Example: To build one of our most popular Pilot Lights, the partnumber would be 30MV20-240 + II + LW + IV + PLL + VIor 30MV20-240DLW-PLLRD

I. BASIC OPERATORCODE DESCRIPTION LIST30MV20-240 Multi-Voltage Pilot Light $60.00

III. LAMP TYPE/COLORCODE DESCRIPTIONLW LED White

V. LENS TYPECODE DESCRIPTION LISTPLL Pilot Light Lens $6.00

U N I Q U E P R O D U C T F E A T U R E S Exclusive!ELIMINATE THE HEADACHE OF

MATCHING SPECIFIC LAMPS WITHLIGHT UNITS!

With our state-of-the-art, super-bright white LEDs and printed circuitboards, this c3controls indicating light unit will handle any voltagefrom 20V to 240V AC or DC without losing light intensity. All youhave to do is pick your lens color. An optional flashing unit is also

available. This compact design is also rated Type 4/4X as standard. All of this is achieved with just one light unit, reducing your inventory!

c3controls LED lamps last 100,000 hours — that’s 11.4 years!

DISCOUNTSCHEDULE A

SE E PAGE 121 F O R LAMP TE C H N I C A L DATA CHAR TS .

115



30mm 30mm 22mm 22mm

30 SE L E C T O R SW I T C H E S |


I T ’ S E A S Y T O B U I L D Y O U R O W N S E L E C T O R S W I T C HSimply pick the code number from each of the sections below and combine them to build yourpart number. See page 4 for more detailed directions.

Selector Switches

I II III IV V* VI*Example: To build one of our most popular Selector Switches, the part number would be I + II + III + IV + V + VIor HSSO3-SHWE-PRNO/PRNO

*NOTE: Contact block configurations are based on circuit *designations (see page 117 for circuit designation charts).


*NOTE: Aluminum clamp rings*are NOT corrosion resistant.

III. HANDLE TYPECODE DESCRIPTION LISTSH Standard $5.00SL Lever $5.00

IV. HANDLE INSERT COLORCODE DESCRIPTIONBE BlueGN GreenGY GreyRD RedWE WhiteYW Yellow

I. BASIC SELECTOR SWITCHOPERATOR FUNCTION

CODE POS./FUNCTION LISTFACTORY SEALED CONTACT BLOCKS

HSS02 2/Maintained $13.00HSROLR 2/Spring Return, L to R $22.00HSRORL 2/Spring Return, R to L $22.00HSS03 3/Maintained $13.00HSROLC 3/Spring Return, L to C $22.00HSRORC 3/Spring Return, R to C $22.00HSROLRC 3/Spring Return, L & R to C $22.00HERMETICALLY SEALED REED CONTACT BLOCKS*HSS02 2/Maintained $13.00HSROLR 2/Spring Return, L to R $22.00HSRORL 2/Spring Return, R to L $22.00HSS0R3 3/Maintained $13.00HSROR3LC 3/Spring Return, L to C $22.00HSROR3RC 3/Spring Return, R to C $22.00HSROR3LRC 3/Spring Return, L & R to C $22.00

*NOTE: Remove “H” from code when ordering a Hermetically Sealed Reed in conjunction with

a Logic Reed Contact Block.

Each operating handle is black with afactory assembled color insert.

V. CONTACT BLOCK CONFIGURATION(LEFT SIDE)

CODE DESCRIPTION LISTFACTORY SEALED, CLASS 1, DIV. 2/ZONE 2, 720 VA

(Blank) Operator without Contact Blocks —CBFSR Contact Block with 1 Normally $48.00


Open/1 Normally ClosedPRNCS 2 Normally Closed Contact Blocks $78.00

Wired in SeriesPRNOP 2 Normally Open Contact Blocks $78.00

Wired in ParallelMID-POWER REED, CLASS 1, DIV. 2/ZONE 2, 180 VA INDUCTIVE(Blank) Operator without Contact Blocks —MPRNO 1 Normally Open Contact Block $30.00MPRNC 1 Normally Closed Contact Block $30.00MPR2NO Contact Block w/2 Normally Open $52.00MPR2NC Contact Block w/2 Normally Closed $52.00MPRNONC Contact Block with 1 Normally $52.00

Open/1 Normally ClosedMPRNCS 2 Normally Closed Contact Blocks $62.00

Wired in SeriesMPRNOP 2 Normally Open Contact Blocks $62.00

Wired in ParallelMEDIUM LOGIC REED, CLASS 1, DIV. 2/ZONE 2,

40 VA INDUCTIVE, 100 WATTS RESISTIVE†(Blank) Operator without Contact Blocks —MLRNO 1 Normally Open Contact Block $18.00MLRNC 1 Normally Closed Contact Block $18.00MLR2NO Contact Block w/2 Normally Open $28.00MLR2NC Contact Block w/2 Normally Closed $28.00MLRNONC Contact Block with 1 Normally $28.00

Open/1 Normally Closed MLRNCS 2 Normally Closed Contact Blocks $38.00

Wired in SeriesMLRNOP 2 Normally Open Contact Blocks $38.00

Wired in ParallelLOGIC REED, CLASS 1, DIV. 2/ZONE 2, 40 WATTS RESISTIVE*†

(Blank) Operator without Contact Blocks —LRNO 1 Normally Open Contact Block $11.00LRNC 1 Normally Closed Contact Block $11.00LRNCS 2 Normally Closed Contact Blocks $24.00

Wired in SeriesLRNOP 2 Normally Open Contact Blocks $24.00

Wired in Parallel

VI. CONTACT BLOCK CONFIGURATION(RIGHT SIDE)

(USE CHART V FROM ABOVE)

† We recommend that any NormallyClosed Logic Reed Contact Blockbe mounted to the operator beforeNormally Open Contact Blocks are mounted.

DISCOUNTSCHEDULE A

*NOTE: Logic Reeds do not require and are not providedwith a Mounting Screw.



30mm 30mm 22mm 22mm

30


| SE L E C T O R SW I T C H E S

30M M H-LI N E SE L E C T O R SW I T C H E SWith our unique universal cam design, c3controls Selector Switches offer multiple functions in a single device eliminating the need to install separate devices to perform individual functionsbased on contact block configuration. In addition, interchangeable selector handles provideproduct selection and field flexibility. All operators feature polyester housings, are UL Listedand are rated Type 4/4X standard for watertight and corrosion resistance. In addition, operatorsare also listed for Type 1, 2, 3, 3R, 12 and 13, and meet global standards requirements.

Standard Handle Lever HandleStandard Handle Lever HandleStandard Handle Lever Handle

O = OPEN X = CLOSED

U N I Q U E P R O D U C T F E A T U R E SSAVE TIME & MONEY - WITH C3CONTROLS, ONE CAM DOES IT ALL!

1. One-Cam does it all vs. our competitors who need up to fifteen cams to perform the same function. This One-Cam designeliminates the need for multiple cam configurations and selector switch configuration nightmares, saving time, inventory,money, and ensuring 100% cam selection configuration accuracy.

2. Our revolutionary U-Cup seal is infused with a Teflon coating to eliminate cracking when exposedto harsh conditions such as heat, dryness and sunlight.

3. All frictional parts are molded with an internal self-lubricant to provide outstanding wear andsmooth cam operations without troublesome greases used by others that attracts dust and otherparticles in the area.

MI X A N D MAT C H AN Y IN S E RT CO L O R A N D SE L E C T O R SW I T C H HA N D L E

HANDLE POSITIONS2-POSITION 3-POSITION

HERMETICALLY SEALED REED CONTACT BLOCK SELECTION FOR 3-POSITION SELECTOR SWITCHESCIRCUIT HANDLE POSITION POWER REED MID-POWER REED MEDIUM REED LOGIC REED MOUNTINGDESIG. LEFT CENTER RIGHT CAT. # CAT. # CAT. # CAT. # POSITIONG X O O PRNO MPRNO MLRNO LRNO LEFTH O X O PRNCS (PRNC/PRNC) MPRNCS (MPRNC/MPRNC) MLRNCS (MLRNC/MLRNC) LRNCS (LRNC/LRNC) BOTH WIRED IN SERIESI O O X PRNO MPRNO MLRNO LRNO RIGHTJ O X X PRNC MPRNC MLRNC LRNC LEFTK X O X PRNOP (PRNO/PRNO) MPRNOP (MPRNO/MPRNO) MLRNOP (MLRNO/MLRNO) LRNOP (LRNO/LRNO) BOTH WIRED IN PARALLELL X X O PRNC MPRNC MLRNC LRNC RIGHT

FACTORY SEALED BLOCK SELECTION FOR 2-POSITION SELECTOR SWITCHESCIRCUIT HANDLE POSITION CONTACT BLOCK MOUNTINGDESIG. LEFT RIGHT CATALOG NO. POSITIONA O X CBFSR EITHER

X O

FACTORY SEALED BLOCK SELECTION FOR 3-POSITION SELECTOR SWITCHESCIRCUIT HANDLE POSITION CONTACT BLOCK MOUNTINGDESIG. LEFT CENTER RIGHT CATALOG NO. POSITIONB X O O CBFSR LEFT

O X OC O O X CBFSR RIGHT

O X O

HERMETICALLY SEALED BLOCK SELECTION FOR 2-POSITION SELECTOR SWITCHESCIRCUIT HANDLE POSITION CONTACT BLOCK MOUNTINGDESIG. LEFT RIGHT CATALOG NO. POSITIOND O X PRNO EITHERE X O PRNC EITHERF O X PRNONC EITHER

X O



30mm 30mm 22mm 22mm

30 LEGEND PL ATES |


I T ’ S E A S Y T O B U I L D Y O U R O W N L E G E N D P L A T ESimply pick the code number from each of the sections below and combine them to build yourpart number. See page 4 for more detailed directions.

Legend Plates

I II III I. STANDARD LEGEND PLATE TYPECODE DESCRIPTION LISTLP Standard 2”h x 2”w $2.00LPN Narrow 2”h x 1.75”w $2.00LPS Short 1.75”h x 2”w $2.00LPT *Tall 2.25”h x 2”w $2.50LPR Standard Round 2.4” Dia. $3.50LPRM Medium Round 2.75” Dia. $4.00LPRJ Jumbo Round 3.75” Dia. $4.50

A. PUSH BUTTONS AND LIGHTSCODE DESCRIPTION00 (Blank)01 Auto02 Close31 Cycle Start100 Cycle Stop03 Down04 Emergency Stop06 Fast101 Fault07 Forward08 Hand32 High33 In09 Inch10 Jog38 Jog Forward39 Jog Reverse34 Low35 Lower11 Manual26 Motor Run12 Off13 On14 Open36 Out27 Overload15 Power Off16 Power On30 Push-To-Reset17 Push-To-Test37 Raise18 Reset19 Reverse20 Run21 Slow22 Start23 Stop24 Test29 Trip25 Up

C. 3-POSITION SELECTORCODE LEGEND LEFT LEGEND CENTER LEGEND RIGHT00 (Blank) (Blank) (Blank)92 Auto Off Hand93 Auto Man Off80 Down Off Up81 Fwd Auto Rev82 Fwd Off Rev83 Hand Off Auto94 High Off Low99 Jog Off Auto90 Local Off Remote84 Manual Off Auto89 Off Run Start85 Off Start Run86 Off 1 295 Open Off Close91 Raise Off Lower96 Slow Off Fast97 Summer Off Winter98 Up Off Down87 1 Off 288 1 2 3

III. LEGEND DESIGNATION

II. FACE AND LETTER COLORCODE FACE COLOR LETTER COLORAL Aluminum Black (Blank) Black White BE Blue White GN Green White RD Red White WE White Black YW Yellow Black

Legend plates feature 2 lines of text with approximately 16 characters per line.*The tall legend plate (LPT) features 3 lines of text with approximately 16 characters per line.

LEGEND PLATESCATALOG NO. DESIGNATION LISTLPRYW-04 Emergency Stop $3.50LP-22 Start $2.00LPT-83 Hand Off Auto $2.50

POPULAR CONFIGURATIONS:

NOT FINDING WHAT YOU NEED INA STANDARD PLATE?

We offer Special and Custom Engraving up to 12” x 24” (304.8mm x 609.6mm).

Please consult factory or see page 119 for details.

DISCOUNTSCHEDULE A

B. 2-POSITION SELECTORCODE LEGEND LEFT LEGEND RIGHT00 (Blank) (Blank)50 Auto Hand68 Auto Manual51 Down Up63 Fast Slow52 Fwd Rev53 Hand Auto73 High Low54 Inch Run75 Left Right70 Local Remote55 Manual Auto56 Off On57 On Off58 Open Close65 Pull Start Push Stop66 Push Off Pull On64 Push On Push Off67 Push To Stop Pull To Start71 Raise Lower59 Rev Fwd60 Run Jog69 Slow Fast61 Start Stop62 Stop Start74 Summer Winter72 Up Down

| LEGEND PL ATESs e r i e s s e r i e s s e r i e s s e r i e s


30mm 30mm 22mm 22mm

30


2.40"(61mm)

2" (50.8mm)

2 Lines16 Characters

7 C

hara

cter

s

7 C

hara

cter

s

1 3/4"


7 C

hara

cter

s

2"

3/4"

3 Lines

7 C

hara

cter

s

7 C

hara

cter

s

16 CharactersMax Per Line

SPEED

0 10

2" (50.8mm)

2" (50.8mm)

2 1/4"(57.2mm)

2" (50.8mm)

2" (50.8mm)

3/4"(19.1mm)

3/4"(19.1mm)

3/4"(19.1mm)

2" (50.8mm)


7 C

hara

cter

s

7 C

hara

cter

s

1 3/4"


7 C

hara

cter

s

2"

3/4"

3 Lines

7 C

hara

cter

s

7 C

hara

cter

s

16 CharactersMax Per Line

SPEED

0 10

2" (50.8mm)

2" (50.8mm)

2 1/4"(57.2mm)

2" (50.8mm)

2" (50.8mm)

3/4"(19.1mm)

3/4"(19.1mm)

3/4"(19.1mm)LP-SP

StandardLPR-SP

Standard RoundLPT-SP

Tall

I T ’ S E A S Y T O B U I L D Y O U R O W N L E G E N D P L A T ESimply pick the code number from each of the sections below and combinethem to build your part number. See page 4 for more detailed directions.

Special Legend Plates

I II III

FE AT U R E BE N E F I T SAll Legend Plates are a 2-ply laminated plastic, laser engraved for a permanent and quality appearance and feature 2 lines of text with approximately 16 characters per line.

TO H E L P S I M P L I F Y YOUR ORDER PROCESS , TEMPLATES A R E AVA I L A B L E B Y CALL ING OURF ACTOR Y AT 1-800-560-8560 OR R E F E R E N C E ONE OF THE THREE DRA WINGS B E L O W.

I. STANDARD LEGEND PLATE TYPECODE DESCRIPTION LISTLP Standard 2”h x 2”w $2.00LPN Narrow 2”h x 1.75”w $2.00LPS Short 1.75”h x 2”w $2.00LPT *Tall 2.25”h x 2”w $2.50LPR Standard Round 2.4” Dia. $3.50LPRM Medium Round 2.75” Dia. $4.00LPRJ Jumbo Round 3.75” Dia. $4.50* The tall legend plate (LPT) features 3 lines of text with

16 characters per line.

II. FACE AND LETTER COLORCODE FACE COLOR LETTER COLORAL Aluminum Black(Blank) Black White BE Blue White GN Green White RD Red White WE White Black YW Yellow Black

III. LEGEND DESIGNATIONCODE DESCRIPTION LISTSP Special Legend $7.00NOTE: $3.00 each when ordering 3 or more of thesame exact legend plate.

Upon receipt of your order, legend plates will be set up as specified and a proof will be sent to you prior to production to ensure accuracy.

To order, submit your drawing to:

Mail: c3controlsAttn: Customer ServiceP.O. Box 496Beaver, PA 15009

Fax: 724-775-5283

Email: [email protected] A

CUSTOM LEGEND PLATES• Available in 2-ply 12” x 24” (304.8mm x 609.6mm)

sheets of laminated plastic for custom laser engraving.

• Add your Corporate Logo! Send us your corporate logo electronically to promote your company image in a clean professional legend plate.

• Initial Set-Up Fee Per Legend Plate: $25/hour (minimum fee $25.00).

• $1.00/Square Inch (minimum $9.00).

To order, submit your drawing to:

Mail: c3controlsAttn: Customer ServiceP.O. Box 496Beaver, PA 15009

Fax: 724-775-5283

Email: [email protected]

(Sample custom plate)

119



30mm 30mm 22mm 22mm

30 AC C E S S O R I E S |


PUSH MAINTAINED FLUSHAND EXTENDED CAPS

Our panel gaskets are constructed of Neoprene for long life and low compression set andprovide a watertight

seal. Panel gaskets aresupplied to accommodate

different panel thickness. In order to meetType 4/4X requirements, at least one 1/16” (1.6mm)gasket must be used. NOTE: All c3controls 30mm operators are provided with gaskets.

PANEL GASKETS

Our Mechanical Interlock features a 2” (50.8mm) center and can be

used to interlock two adjacent operators. This may also beused to interlock a two-unitmaintained/momentary assembly. NOTE: Factoryinstallation recommended.

To simplify tightening and loosening of standard

polyester and aluminum 1-3/8”(34.9mm) octagonalclamp rings. Won’t

scratch your lens or panel.

CLAMP RING WRENCH

HOLE PLUG

Anti-rotationdevice for usewith 30mm pushbuttons, selectorswitches and

pilot lights to provide additional

protection from rotation and aid in alignment. This product isoptional with c3controls gasket technology. NOTE: Can only be used in conjunction with speciallegend plates that have the “up notch” design.

THRUST & TRIM WASHERS

Use with a secondarystandard cap and

mechanical interlock to provide two

button momentary/maintained operation

or use on adjacent operators withmechanical interlock to provide two-button maintained/maintained operation. Comes with our standard polyester clamp ring. An optional polished aluminum clamp ring is also available, add prefix “A” to catalog code and increase theprice $2.00. NOTE: Aluminum clamp rings areNOT corrosion resistant.

MECHANICAL INTERLOCK

LOCK OFF ATTACHMENTSc3controls offers a wide variety of 30mm corrosiveresistant lock-off attachments for maintained andmomentary push buttons and selector switches.Our LOAX, LOAM and LOAP lock-offs permit

locking operators in thedepressed position. Our

LOAFC lock-off covers and locks the operator so itsposition cannot be changedand features a 1/4” (6.4mm)diameter padlocking hasp.

GUARD ATTACHMENTOur PPGD guards against

accidental operation and ismade of a high strengthpolyester material.

LOAFC

LOAX/LOAM/LOAP

DISCOUNTSCHEDULE A

Our unique Reset Push Buttonmounts in a standard 1-13/64” (30.5mm) hole andaccepts either 20 hex headbolts or 20 thread rod to provide adjustable extensionand save on all rod cutting andfitting labor. Universal styles includetwo bolts to cover 1” to 3” (25.4mm to 76.2mm)space from cover to overload reset rod. It is ratedType 4/4X as standard.

RESET PUSH BUTTON

CODE FITS LISTPPGD Maintained Push Buttons $20.00

CODE DESCRIPTION LISTMI 30mm Mechanical Interlock $12.00

CODE DESCRIPTION LISTHP 30mm Grey Hole Plug $4.00

CODE FITS LISTLOAX Standard Extended Cap $16.00LOAM Standard Momentary $16.00

Mushroom CapLOAP Push-Pull Maintained $16.00

Mushroom Cap (PPMC) or Push Maintained Extended Cap (PMXC)

LOAFC Most Push Buttons and $25.00Selector Switches

CODE DESCRIPTION LISTPG2 1/16” (1.6mm) Gasket $0.50PG6 3/16” (4.8mm) Gasket $0.50

CODE DESCRIPTION LISTTTW 30mm Anti-Rotation Washers $1.00

COLOR FLUSH EXTENDED LISTCODE CODE

Black PMFCBK PMXCBK $22.00Green PMFCGN PMXCGN $22.00Red PMFCRD PMXCRD $22.00Yellow PMFCYW PMXCYW $22.00

CODE DESCRIPTION LISTCRW 30mm Clamp Ring Wrench $10.00

CODE DESCRIPTION LISTRPB Reset Push Button $ 9.00RPB-B RPB w/Bolts (1/4-20 x 1-3/4” & 3”) $10.00RPB-W RPB w/Washers $10.00RPB-BW RPB w/Bolt & Washer Set $11.00RPBB 2 Bolts (1/4-20 x 1-3/4” & 3”) $ 1.00RPBW Washer Set $ 1.00Other bolt lengths available - please consult factory.

Use to seal unused panel holes.Our hole plug comes with additional sealing panel gaskets to ease installation and is rated Type 4X.

We offer four types of 30mm extended clamp ringsthat guard against accidental operation. Use ourExtended Clamp Rings (ECR or AECR) with flushcaps, our Clear Guarded Clamp Ring (EECR) withilluminated push buttons and our Large ExtendedClamp Ring (LECR) with flush or extended caps,which also provides easier access to your push buttons.

FOR USE WITH NON-ILLUMINATED CAPSCODE DESCRIPTION LISTECR Extended Ring $3.00LECR Large Extended Ring $5.00AECR Aluminum Extended Ring $5.00

FOR USE WITH ILLUMINATED CAPSCODE DESCRIPTION LISTEECR Guarded Clear Polyester Ring $4.00

EXTENDED CLAMP RINGS

LECR EECR ECR

AECR



30mm 30mm 22mm 22mm

30


| AC C E S S O R I E S

LED, INCANDESCENT & NEON REPLACEMENT LAMPS

LAMP TECHNICAL DATALAMP C3 LAMP RATED LUMENS DESIGN LIFE CURRENT SHOCK & VIBRATION TYPE PART NUMBER VOLTAGE (HRS.) DRAW (MA) PERFORMANCEIncd. FVB6 6.3V 0.65 mscd 5,000 250 Very GoodIncd. FVB12 14V 0.31 mscd 15,000 80 GoodIncd. FVB24 28V 0.62 mscd 7,500 80 GoodIncd. FVB55 55V 1.10 mscd 5,000 50 GoodIncd. FVB120 120V 0.36 mscd 10,000+ 20 GoodNeon FVB120N (G or R) 95-135V DIM 10,000 2 Very GoodLED LED6 6V 1,000-2,180 mcd* 100,000 20 ExcellentLED LED12 12V 1,000-2,180 mcd* 100,000 20 ExcellentLED LED24 24V 1,000-2,180 mcd* 100,000 20 ExcellentLED LED48 48V 1,000-2,180 mcd* 100,000 20 ExcellentLED LED120 120V 1,000-2,180 mcd* 100,000 20 Excellent*Average range — @20ma Max.

DISCOUNTSCHEDULE A

DISCOUNTSCHEDULE C

H-LINE UL TEMPERATURE RATINGSLAMP TYPE CLASS DESIGNATION TEMPERATUREFULL VOLTAGE INDICATING LIGHTS (Temperature rating is determined based on maximum lamp temperature)Incandescent Class 1, Div 2, Groups A,B,C,D T4A, 248° F (120° C)

Class 1, Zone 2 IIC T4A, 248° F (120° C)Neon Class 1, Div 2, Groups A,B,C,D T6, 185° F (85° C)

Class 1, Zone 2 IIC T6, 185° F (85° C)LED Class 1, Div 2, Groups A,B,C,D T6, 185° F (85° C)

Class 1, Zone 2 IIC T6, 185° F (85° C)RESISTOR LIGHTS (Temperature rating is a function of the maximum lamp or resistor temperature obtained under power)Incandescent Class 1, Div 2, Groups A,B,C,D T3C, 320° F (160° C)

Class 1, Zone 2 IIC T3C, 320° F (160° C)Neon Class 1, Div 2, Groups A,B,C,D T6, 185° F (85° C)

Class 1, Zone 2 IIC T6, 185° F (85° C)LED Class 1, Div 2, Groups A,B,C,D T6, 185° F (85° C)

Class 1, Zone 2 IIC T6, 185° F (85° C)TRANSFORMER LIGHTS (Temperature rating is a function of the maximum transformer winding temperature)Incandescent Class 1, Div 2, Groups A,B,C,D T4A, 248° F (120° C)

Class 1, Zone 2 IIC T4A, 248° F (120° C)LED Class 1, Div 2, Groups A,B,C,D T4A, 248° F (120° C)

Class 1, Zone 2 IIC T4A, 248° F (120° C)MULTI-VOLTAGE LIGHTS LED Class 1, Div 2, Groups A,B,C,D T4A, 248° F (120° C)

Class 1, Zone 2 IIC T4A, 248° F (120° C)

LED LampsLED

I II III To order LED Lamps, thepart number would be LED + II + III.

I. LAMP TYPECODE DESCRIPTIONLED LED Lamp

III. LAMP COLORCODE COLOR LISTAR Amber $14.00BE Blue $14.00GN Green $14.00RD Red $14.00WE White $14.00

Incandescent Lamps

Neon Lamps

LAMP REMOVAL TOOL

CODE VOLTAGE LISTFVB6 6V $2.00FVB12 12V $2.00FVB24 24V $2.00FVB55 55V $4.00FVB120 120V $4.00FVB6F 6V Flashing $6.00

CODE VOLTAGE COLOR LISTFVB120NG 120V Green $2.00FVB120NR 120V Red $2.00

CODE DESCRIPTION LISTLRT Lamp Removal Tool $4.00

II. VOLTAGECODE DESCRIPTION6 6V*12 12V24 24V48 48V120 120V**NOTE: No leakage protection.

Used to facilitate the removal of lamps particularly in illuminated push buttons and push-to-test operators.

NOTE: DiscountSchedule A does notapply to Lamp RemovalTool.

New &Improved!

c3controls offers a full range of lamp options in a miniature bayonet base for direct interchangeability whichprovides flexibility in choosing the best lamp for each installation application. Multiple voltage options inIncandescent, LED and Neon lamps are available. Please refer to the charts at the bottom of the page forlamp technical data and temperature ratings. To determine the appropriate replacement lamp based onyour operator voltage, please refer to the chart on page 95.

Features built-in leakage protection.



30mm 30mm 22mm 22mm

30 DIMENSIONS |


MOMENTARY NON-ILLUMINATED H-LINE PUSH BUTTONS

1 3/16"(30.2mm)

2 1/8"(54mm)

2 1/4"(57.2mm)

Illum PB

9/16"(14.3mm)

1 3/16"(30.2mm)

2 1/8"(54mm)

2 7/16"(61.9mm)

Sel Switch

9/16"(14.3mm)

1 3/16"(30.2mm)

2 1/8"(54mm)

2 3/8"(60.3mm)

9/16"(14.3mm)

Non Illum Push Button

7/16"(11.1mm)

2 3/16"(55.6mm)

9/16" (14.3mm)

Mtg. bracket

Panel Thk.(3/16" (4.8mm) shown)

1 3/8"(34.9mm)

2 1/

8" (5

4mm

)

2"(50.8mm)

1 9/16"(39.7mm)

2 7/16"(61.9mm)

Mtg. bracket

1 5/

8"(4

1.3m

m)

7/16"(11mm)

1 3/8"(34.9mm)

7/16"(11.1mm)

2 3/16"(55.6mm)

9/16" (14.3mm)

Mtg. bracket


1 3/8"(34.9mm)

2 1/

8" (5

4mm

)

2"(50.8mm)

1 9/16"(39.7mm)

2 7/16"(61.9mm)

Mtg. bracket

1 5/

8"(4

1.3m

m)

7/16"(11mm)

1 3/8"(34.9mm)

NON-ILLUMINATED OPERATOR

(SHOWN WITH FLUSH CAP & FACTORY SEALED CONTACT BLOCK)

9/16"(14.3mm)

3/8"(9.5mm)

2 1/8"(54mm)

1 5/8"(41.3mm) Operator

Hsg.

1 9/16"(39.7mm)

Operator Hsg.

2 7/16"(61.9mm)

Mtg. bracket

MOMENTARY EXTENDED CAP

1 3/8"(34.9mm)

1 9/16"(39.7mm)

2" (50.8mm)

1 9/16"(39.7mm)

2 1/8"(54mm)

1 5/8"(41.3mm)

2 7/16"(61.9mm)

Mtg. bracket

MOMENTARY 1.5” (38MM) MUSHROOM CAP

MOMENTARY 1.5” (38MM) SHROUDED MUSHROOM CAP MOMENTARY 2.25” (57.2MM) SHROUDED JUMBO MUSHROOM CAP

1 3/8"(34.9mm)

2 1/4"(57.2mm)

2" (50.8mm)

1 9/16"(39.7mm)

Operator Hsg.

2 7/16"(61.9mm)

Mtg. bracket

2 1/8"(54mm)

1 5/8"(41.3mm)Operator

Hsg.

MOMENTARY 2.25” (57.2MM) JUMBO MUSHROOM CAP

13/16"(20.6mm)

1 1/2"(38.1mm)

2 1/

8" (5

4mm

)

2" (50.8mm)

1 9/16"(39.7mm)

Operator Hsg.

2 7/16"(61.9mm)

Mtg. Bracket

13/16" 2 3/16"9/16"Mtg.

bracket

Panel Thk.(3/16" shown)

1 1/2"

1 5/

8"(4

1.3m

m)

Ope

rato

r H

sg.

MOMENTARY FLUOROSILICONE RUBBER BOOT NON-ILLUMINATED PUSH BUTTON MOUNTING BRACKET

1 7/8"(47.9mm)

1 7/16"(36.5mm)

2 1/

8" (

54m

m)

1 5/

8"(4

1.3m

m)

Ope

rato

r H

sg.

1 9/16"(39.7mm)

Operator Hsg.

2 7/16" (61.9mm) Mounting Bracket

2" (50.8mm)

2 5/8"(66.7mm)

1 7/16"(36.5mm)

1 1/8"(28.6mm)

2 1/

8" (

54m

m)

2" (50.8mm)


Hsg.1

5/8"

(41.

3mm

)O

pera

tor

Hsg

.

2 7/16"(61.9mm)

Mounting bracket

2 5/8"(66.7mm)

1 7/16"(36.5mm)

1 1/8"(28.6mm)

2 1/

8" (

54m

m)

2" (50.8mm)


Hsg.

1 5/

8"(4

1.3m

m)

Ope

rato

r H

sg.

2 7/16"(61.9mm)

Mounting bracket

Fully-assembled operators come standard with one 3/16” (4.8mm) and three 1/16” (1.6mm) gaskets. See page 126 for mounting gasket specifications.



30mm 30mm 22mm 22mm

30


2-POSITION PUSH-PULL MAINTAINED OPERATOR

(SHOWN WITH 2.25” (57.2MM) JUMBO MUSHROOM CAP)

1 7/16"(36.5mm)Out Dim.

1 3/16"(30.2mm)In Dim.

1 5/8"(41.3mm)

2 7/16"(61.9mm)

Mtg. bracket

1 7/16"Out Dim.

3 1/16"

1 5/8"

Panel Thk.(3/16" shown)

1 3/16"In Dim.

2 1/8"(54mm)

1 5/8"(41.3mm) Operator

Hsg.

2-POSITION PUSH-PULL MAINTAINED

1.5” (38MM) MUSHROOM CAP

1 7/16"(36.5mm)Out Dim.

2 1/

8" (

54m

m)

9/16"(14.3mm)

Mtg. Bracket

1 5/

8"(4

1.3m

m)

Ope

r. H

sg.

2" (50.8mm)

1 9/16"(39.7mm) Oper. Hsg.

2 7/16" (61.9mm)Mounting Bracket


2 3/16"(55.6mm)

2 1/4"(57.2mm)

1 3/16"(30.2mm)In Dim.

MAINTAINED NON-ILLUMINATED H-LINE PUSH BUTTONS

MOMENTARY ILLUMINATED H-LINE PUSH BUTTONS

1 7/16"

2 1/4"(57.2mm)

2 1/8"(54mm)

1 7/16"(36.5mm)

1 11/16"(42.9mm)

Panel Thk.3/16" (4.8mm)

1 3/16"(30.2mm)

2 1/8"(54mm)

2 1/4"(57.2mm)

Illum PB

9/16"(14.3mm)

1 3/16"(30.2mm)

2 1/8"(54mm)

2 7/16"(61.9mm)

Sel Switch

9/16"(14.3mm)

1 3/16"(30.2mm)

2 1/8"(54mm)

2 3/8"(60.3mm)

9/16"(14.3mm)


ILLUMINATED PUSH BUTTON MOUNTING BRACKET


ILLUMINATED TRANSFORMER, RESISTOR

AND DUAL INPUT OPERATORS (SHOWN WITH HIPBCM)

ILLUMINATED TRANSFORMER AND RESISTOR OPERATORS

(SHOWN WITH IMC)ILLUMINATED FULL VOLTAGE OPERATOR

(SHOWN WITH IMC)

2-POSITION PUSH-PULL MAINTAINED ILLUMINATED H-LINE PUSH BUTTONS


7/8"(22.5mm)

2 7/16"(61.9mm)

1 7/16"(36.5mm) 2 1/4"

(57.2mm)

2 1/8"(54mm)

1 3/4"(44.5mm)

2 1/4"(57.2mm)

1 9/16"(39.7mm)

1 1/2"(38.1mm)

2 1/4"(57.2mm)

3 3/16"(80.9mm)11/16"

(17.5mm)

To end of transformer/resistor/ dual-input housing


ILLUMINATED FULL VOLTAGE OPERATOR

(SHOWN WITH HIPBC)

3 9/16"(90.5mm)1 7/16"

(36.5mm)


1 9/16"(39.7mm)

1 5/8"(41.3mm)

2 1/8"(54mm)


| DIMENSIONS




30mm 30mm 22mm 22mm

30 DIMENSIONS |


H-LINE PILOT LIGHTS

FULL VOLTAGE PILOT LIGHT OPERATOR

(SHOWN WITH PLL)

1 1/16"(27mm)

3/4"(19.1mm)

1 3/4"(44.5mm)

1 5/8"(41.3mm)


1 3/4"(44.5mm)

1 5/8"(41.3mm)

1 1/16"(27mm)

2 3/16"(55.6mm)

1 9/16"(39.7mm)


TRANSFORMER & RESISTOR PILOT

LIGHT OPERATORS

(SHOWN WITH PLL)

1 1/16"(27mm)

2 3/16"(55.6mm)

1 5/8" (41.3mm) 7/8"(22.5mm)Add'lblocks


1 5/8"(41.3mm)

1 3/4"(44.5mm)

DUAL INPUT

PILOT LIGHT OPERATOR

(SHOWN WITH PLL)

FULL VOLTAGE PUSH-TO-TEST OPERATOR

(SHOWN WITH HIPBCM)

PUSH-TO-TEST H-LINE PILOT LIGHTS

TRANSFORMER & RESISTOR PUSH-TO-TEST OPERATORS

(SHOWN WITH HIPBC)

1 1/2"(38.1mm)

3 3/16"(81mm)

2 1/8"(54mm)

1 5/8"(41.3mm)


Hsg.

2 7/16"(61.9mm)

Mtg. bracket

1 3/16"(30.2mm)

2 1/8"(54mm)

2 1/4"(57.2mm)

Illum PB

9/16"(14.3mm)

1 3/16"(30.2mm)

2 1/8"(54mm)

2 7/16"(61.9mm)

Sel Switch

9/16"(14.3mm)

1 3/16"(30.2mm)

2 1/8"(54mm)

2 3/8"(60.3mm)

9/16"(14.3mm)


ILLUMINATED PUSH-TO-TEST MOUNTING BRACKET

2 1/4"(57.2mm)

2 1/8"(54mm)


1 3/16"(30.2mm)

3 1/8"(79.4mm)

MULTI-VOLTAGE H-LINE PILOT LIGHT

MULTI-VOLTAGE PILOT LIGHT (SHOWN WITH PLL)

1 1/16"(27mm)

2 1/16"(52.4mm)

1 9/16"(39.7mm)


1 5/8"(41.3mm)

1 5/8"(41.3mm)

1"(25.4mm)

Fully-assembled operators come standard with one 3/16” (4.8mm) and two 1/16” (1.6mm) gaskets. See page 126 for mounting gasket specifications.

Fully-assembled operators come standard with four 1/16” (1.6mm) gaskets. See page 126 for mounting gasket specifications.


2 1/4"(57.2mm)

2 1/8"(54mm)


1 3/16"(30.2mm)

3 1/8"(79.4mm)

V I S I T W W W . C 3 C O N T R O L S . C O MT O D O W N L O A D C A D D R A W I N G S



30mm 30mm 22mm 22mm

30


H-LINE SELECTOR SWITCHES

SELECTOR SWITCH OPERATOR

(SHOWN WITH STANDARD HANDLE)

1 1/8"(28.6mm)

3 1/16"(77.8mm)9/16" (14.3mm)Mtg. bracket

1 3/8"(34.9mm)


2 7/16"(61.9mm)

Mtg. bracket


Hsg.


Hsg.

2 1/8"(54mm)

SELECTOR SWITCH LEVER HANDLE

1" (25.4) Swing Radius

1 1/8"(28.6mm)

31/32"(787.4mm)

1 3/16"(30.2mm)

2 1/8"(54mm)

2 1/4"(57.2mm)

Illum PB

9/16"(14.3mm)

1 3/16"(30.2mm)

2 1/8"(54mm)

2 7/16"(61.9mm)

Sel Switch

9/16"(14.3mm)

1 3/16"(30.2mm)

2 1/8"(54mm)

2 3/8"(60.3mm)

9/16"(14.3mm)


SELECTOR SWITCH MOUNTING BRACKET

H-LINE CONTACT BLOCKSFACTORY SEALED CONTACT BLOCK POWER REED, MID-POWER REED & MEDIUM LOGIC

REED CONTACT BLOCKS

NC contacts

NO contacts

1 15/16"(49.2mm)

1 1/2"(38.1mm)

1 1/8"(28.6mm)

1"(25.4mm)

1 11/16"(42.9mm)

NC contacts

NO contacts

1 15/16"(49.2mm)

1 1/2"(38.1mm)

1 1/8"(28.6mm)

1"(25.4mm)

1 11/16"(42.9mm)

1 11/16"(42.9mm)

1 3/16"(30.2mm)

2 5/16"(58.7mm)

2 13/16"(71.4mm)

13/16"(20.6mm)LOGIC REED CONTACT BLOCK

7/8"(22.5mm)

1 3/8"(34.9mm)

1 11/16"(42.9mm)

7/8"(22.5mm)

11/16"(17.5mm)

5/16"(7.9mm)

5/16"(7.9mm)

7/8"(22.5mm)

1 3/8"(34.9mm)

1 11/16"(42.9mm)

7/8"(22.5mm)

11/16"(17.5mm)

5/16"(7.9mm)

5/16"(7.9mm)


| DIMENSIONS



30mm 30mm 22mm 22mm

30 DIMENSIONS |


1 1/2"(38.1mm)

1 3/8"(34.9mm)

MAINTAINED EXTENDED

PUSH BUTTON CAP

H-LINE RESET PUSH BUTTON

RESET PUSH BUTTON

1/2"(12.7mm)

Travel

7/16"(11.1mm)

1 3/8"(34.9mm)

MAINTAINED FLUSH & EXTENDED H-LINE PUSH BUTTON CAPS

MAINTAINED FLUSH PUSH BUTTON CAP

(SHOWN WITH AN OPERATOR AND CONTACT BLOCK)

1 3/8"(34.9mm)

2 3/16"(55.6mm)

9/16"(14.3mm)

Mtg. Bracket


1 3/8"(34.9mm)

2"(50.8mm)

1 9/16"(39.7mm)

Operator Hsg.

2 7/16"(61.9mm)

Mtg. Bracket

2 1/8"(54mm)


Hsg.

LOCK-OFF ATTACHMENT

2 1/16"(52.4mm)

2 9/16"(65.1mm)

7/8"

(22.

5mm

)

2 1/16"(52.4mm)

2 9/16"(65.1mm)

Hinge Point

1 1/

4"(3

8.1m

m)

11/16"(17.5mm)

1 7/8"(47.9mm)

2"(5

0.8m

m)

2"(50.8mm)

1 7/

8"(4

7.9m

m)

1 7/

8"(4

7.9m

m)

2"(5

0.8m

m)

1 3/16"(30.2mm)

2 11/16"(68.3mm)

2 9/16"(65.1mm) from hinge

2 1/16"(52.4mm) from hinge 1 9/16"

(39.7mm)closed height

1 5/16"(33.3mm)cavity height

Fully-assembled operators come standard with one 3/16” (4.8mm) and three 1/16” (1.6mm) gaskets. See below for mounting gasket specifications.

Fully-assembled operators come standard with one 3/16” (4.8mm) and three 1/16” (1.6mm) gaskets. See below for mounting gasket specifications.

MOUNTING GASKETSPANEL THICKNESS # OF GASKETS NEEDEDIN DECIMALS 3/16” (4.8MM) & 1/16” (1.6MM)

less than .080 1 4.080 – .132 1 3.133 – .185 1 2.186 – .238 1 1.239 – .291 0 3.292 – .344 0 2NOTE: Remove one 1/16” (1.6mm) gasket when using a

legend plate.

LOAFC

c3 Controls Cbfs - Cbfsr

Documents

Transcript of c3 Controls Cbfs - Cbfsr