C103 frequency Divider / Multiplier MKII · frequency divider / multiplier mkii c103 div min max...
Transcript of C103 frequency Divider / Multiplier MKII · frequency divider / multiplier mkii c103 div min max...
USER MANUAL
C103 frequency Divider / Multiplier MKII
FREQUENCY DIVIDER / MULTIPLIER MKIIC103
DIV
MIN MAX
MULT
MIN MAX
F
CV LEVEL
MIN MAX
DIST OUT
F2
CV INDIST
MULT IN F2-M OUT F4-M OUT MULT MIX SW MIX
F2-D OUT MIX OUTDIV IN DIV MIXF4-D OUT
MULT
DIV
DIV
MIN MAX
MULT
MIN MAX
F4DIV
MIN MAX
MULT
MIN MAX
MULT
DIV
DIST
MIN MAX
MULT
DIV
C103 Frequency Divider / Multiplier MKII
1HTTP://WWW.CORSYNTH.COM
The C103 Frequency Divider / Multiplier MKII includes two frequency dividers and two frequency multipliers. It generates four new signals which frequencies are one / two octaves higher / lower than the original input.
This new MKII version, adds a lot of functionality to the original design. It has four built in mixers , new individual outputs and new voltage controlled distortion circuit with independent output. Additionally each divider and multiplier stage has his own level potentiometer.
Thanks to these new additions the divider and multiplier circuits can be used independently. For example a VCO can be connected to the divider to use it as suboctave generator and a LFO can be connected to the multiplier to get synchronized modulations.
The C103 Frequency Divider / Multiplier MKII can be used in many di�erent ways :
- As subctave Generator- To create complex and rich sounds from a simple waveform.- To create synchronized modulations- As a clock divider- As frequency multiplier- To create complex modulation signals- As pattern generator
and more...
If you like the original C103 , this new version retains the same functionality using the Switched mixer but it goes one step further. Thanks to the new level potentiometers , the divider and the multiplier of each stage can have di�erent signal levels.
The frequency divider input is normalized to the multiplier input, If nothing is connected to the divider input, it will take the signal connected to the multiplier input as its input signal.
C103 FrequencyDivider / Multiplier MKII
FREQUENCY DIVIDER / MULTIPLIER MKIIC103
DIV
MIN MAX
MULT
MIN MAX
F
CV LEVEL
MIN MAX
DIST OUT
F2
CV INDIST
MULT IN F2-M OUT F4-M OUT MULT MIX SW MIX
F2-D OUT MIX OUTDIV IN DIV MIXF4-D OUT
MULT
DIV
DIV
MIN MAX
MULT
MIN MAX
F4DIV
MIN MAX
MULT
MIN MAX
MULT
DIV
DIST
MIN MAX
MULT
DIV
C103 frequency divider / multiplier mkII
2HTTP://WWW.CORSYNTH.COM
FREQUENCY DIVIDER / MULTIPLIER MKIIC103
DIV
MIN MAX
MULT
MIN MAX
F
CV LEVEL
MIN MAX
DIST OUT
F2
CV INDIST
MULT IN F2-M OUT F4-M OUT MULT MIX SW MIX
F2-D OUT MIX OUTDIV IN DIV MIXF4-D OUT
MULT
DIV
DIV
MIN MAX
MULT
MIN MAX
F4DIV
MIN MAX
MULT
MIN MAX
MULT
DIV
DIST
MIN MAX
MULT
DIV
C103 Frequency Divider / Multiplier MKII
Divider F level
Divider F2 level
Divider F4 level
Distortion CV level
Distortion level
Divider F2 output
Divider input
Multiplier input
Multiplier F2 output
Multiplier F level
Multiplier F2 level
Multiplier F4 level
Distortion CV input
Distortion output
Divider mix output
Mix output
Divider F4 output
Switched mix output
Switch to chose betweenF Multiplier or Divider
Switch to chose betweenF2 Multiplier or F2 Divider
Switch to chose betweenF4 Multiplier or F4 Divider
Multiplier mix output
Multiplier F4 output
C103 frequency divider / multiplier mkII
3HTTP://WWW.CORSYNTH.COM
C103 MKII BLOCK DIAGRAM
DIST CV IN
PUT
SW M
IX OU
T
∑
MU
LT MIX O
UT
MU
LT INPU
T
DIV IN
PUT
∑D
IV MIX O
UT
∑M
IX OU
T
F2 D O
UT
F4 D O
UT
F2 M O
UT
F4 M O
UT
F MU
LTF2 M
ULT x 2
F4 MU
LT x 4
F DIV
F2 DIV / 2
F4 DIV / 4
∑
DISTO
RTION
DISTO
RTION
OU
T
C103 frequency divider / multiplier mkII
4HTTP://WWW.CORSYNTH.COM
CONTROL DESCRIPTION
DIVIDER F LEVELThis potentiometer sets the level of the divider input. This level a�ects to the Mix out , Divider Mix out and Switched Mix out.
DIV
MIN MAX
F
DIV F2 LEVELThis potentiometer sets the level of the �rst suboctave, generated from the the divider input. This level a�ects to the Mix out , Divider Mix out and Switched Mix out.
F2DIV
MIN MAX
DIVIDER F4 LEVELThis potentiometer sets the level of the second subocta-ve, generated from the the divider input. This level a�ects to the Mix out , Divider Mix out and Switched Mix out.
F4DIV
MIN MAX
MULTIPLIER F LEVELThis potentiometer sets the level of the multiplier input. This level a�ects to the Mix out , Multiplier Mix out and Switched Mix out.
MULT
MIN MAX
F
MULTIPLIER F2 LEVELThis potentiometer sets the level of the multipliers �rst stage. The signal is generated using the multiplier input. This level a�ects to the Mix out , Multiplier Mix out and Switched Mix out.
MULT
MIN MAX
F2
C103 frequency divider / multiplier mkII
5HTTP://WWW.CORSYNTH.COM
MULTIPLIER F4 LEVELThis potentiometer sets the level of the multipliers second stage. The signal is generated using the multiplier input. This level a�ects to the Mix out , Multiplier Mix out and Switched Mix out.
F SWITCH SELECTORThis switch allows to select the input for the �rst channel of the Switched Mixer. The signal is selected post-fader. The signals available are DIV F and MULT F
MULT
MIN MAX
F4
MULT
DIV
F2 SWITCH SELECTORThis switch allows to select the input for the second chan-nel of the Switched Mixer. The signal is selected post-fader. The signals available are DIV F2 and MULT F2
MULT
DIV
F4 SWITCH SELECTORThis switch allows to select the input for the third channel of the Switched Mixer. The signal is selected post-fader. The signals available are DIV F4 and MULT F4
MULT
DIV
DISTORTION LEVELThe distortion circuits takes the signal directly from the Mix Output. This potentiometer sets the amount of distortion. Depending on the level of the input signal, the circuit can start to distort even with the potentiome-ter at minimum.
DIST
MIN MAX
DIST OUTDISTORTION OUTOutput of the the distortion circuit.
C103 frequency divider / multiplier mkII
6HTTP://WWW.CORSYNTH.COM
DISTORTION CVDistortion CV input. The potentiomenter LEVEL sets the amount of modulation sent to the distortion circuit.
DIV INDIVIDER INPUTFrequency divider input. This input accepts any kind of basic waveform ( square wave, triangle wave, saw wave, sine wave… ). If nothing is patched to this input , it is internally connected to the multiplier input. This connec-tion breaks when a jack is inserted.
CV LEVEL
MIN MAX
CV IN
F2-D OUT F2 DIVIDER OUTPUTOutput of the �rst stage of the divider circuit. The output is a square wave with a frequency one octave below the frequency of the divider input signal.
F4-D OUT F4 DIVIDER OUTPUTOutput of the second stage of the divider circuit. The output is a square wave with a frequency two octaves below the frequency of the divider input signal.
DIV MIXDIVIDER MIX OUTPUTThis is the output of the Divider Mixer. The level of each stage is set by the DIV potentiometers.
MIX OUT MIX OUTPUTThis output is the sum of the Divider Mixer and the Multi-plier Mixer. The level of each channel is set by the DIV and MULT potentiometers.
C103 frequency divider / multiplier mkII
6HTTP://WWW.CORSYNTH.COM
MULT INMULTIPLIER INPUTFrequency multiplier input. The frequency multiplier works well with sine, triangle or similar waveforms. If a saw wave is connected to this input it will be converted to a triangle wave ( with the same frequency of the original) at the F2 output.
F2-M OUT F2 MULTIPLIER OUTPUTOutput of the �rst stage of the multiplier circuit. The output is waveform with a frequency one octave higher than the frequency of the multiplier input signal.
F4-M OUT F4 MULTIPLIER OUTPUTOutput of the second stage of the multiplier circuit. The output is waveform with a frequency two octaves higher than the frequency of the multiplier input signal.
MULT MIXMULTIPLIER MIX OUPUTThis is the output of the Multiplier Mixer. The level of each stage is set by the MULT potentiometers.
SW MIXSWITCHED MIX OUTPUTThis is the output of the Switched Mixer. This mixer has three chanels with two inputs each. The active input is selected using the F, F2 and F4 switches The level of each channel is set by the DIV and MULT potentiometers.
C103 frequency divider / multiplier mkII
8HTTP://WWW.CORSYNTH.COM
Power connectors
Module Format : 5U, MU format ( Synthesizers.com, Moog ) Module Width : 2 MU ( Moog unit ) Module Depth : 52 mm ( 2,05 inches ) Power : +15V@75mA , -15V@80mA Power connectors : Synthesizers.com , MOTM ( 4 pin )
TECHNICAL DATA
+15V+5V-15VN/C GND
Synthesizers.com
GND +15V-15V GND
MOTM
IMPORTANT !!!!This module has two power connec-tors (Synthesizers.com and MOTM). Only one is needed to power the module. (Synthesizers.com or MOTM).
Never connect both at the same time.
Synthesizers.compower connector
MOTMpower connector
C103 frequency divider / multiplier mkII
9HTTP://WWW.CORSYNTH.COM
MODULAR LEVEL
MIN MAX
MODULAR SYNTHS