C 1203-1204 F17-08 USA · 2019. 2. 25. · 1 -1203 1 -1204 Guided Flat Belt Conveyor SV Series...
1
-1203 1 -1204 1 Guided Flat Belt Conveyor SV Series Guided Belt to Prevent Lateral Movement, Center Drive, 2-Groove Frame (Pulley Dia. 30mm) QFeatures: Streamlined structure has achieved the low cost. The center drive section is adjustable. The conveyor maintains good running straightness by the use of the guided belt to prevent lateral movement. Frame Motor Cover1 Motor Cover2 Pulley Holder MMaterial Aluminum Aluminum Low Carbon Steel Aluminum SSurface Treatment Clear Anodize Paint Paint Paint EIn case of selectiong Optional Belts, please select motor manufacturer A or B (Motor C is applicable for Standard Belt only.) EConnect the motor so that the belt rotates in the direction of conveyance. For connection diagram, and details of motor and inverter, see wP. 1267. EWhen "No motor, gearhead" is selected, the motor mounting hole pitch will vary depending on the motor's power rating. Please see Technical Information in our Conveyor Selection web site for the dimension details. EWhen "No motor, gearhead" is selected, this unit will be delivered unassembled. The customer is to assemble the unit according to the included assembly instructions. See our Conveyor Selection site for assembly procedures and packaging details. ENote that warpage might occur in belts with the guided belt depending on the number of plies (thickness). Part Number Width B (mm) Selection Length L 5mm Increment Motor Belt Specification Motor Manufacturer Selection EPrices vary by manufacturer. Output (W) Voltage (V) Specification Gearhead Reduction Ratio SVKR 50 100 150 200 250 390~3000 6 25 40 60 90 (Single-Phase) TA100 TA110 TA115 T200 TA200 TA220 TA230 IM (Constant Speed Motor) SCM (Variable Speed Motor) 5 18 60 150 7.5 25 75 180 9 30 90 12.5 36 100 15 50 120 H (General Specifications, Green) W (General Specifications, White) G (For Sliding, Green) S (For Sliding, White) D (Static Conductive) O (Oil Resistant, Navy Blue) N (Non-Stick Food Grade, White) J (No Belt) *For belts other than the above, select from Belt Specification below. A (Panasonic Motor) B (Oriental Motor) C (Taiwanese Motor) 25 40 60 90 (Three-Phase) SA200 SA220 SA230 IM (Constant Speed Motor) INV (Induction Motor + Inverter) 300 400 40 60 90 (Single-Phase) TA100 TA110 TA115 T200 TA200 TA220 TA230 IM (Constant Speed Motor) SCM (Variable Speed Motor) (Three-Phase) SA200 SA220 SA230 IM (Constant Speed Motor) INV (Induction Motor + Inverter) X5~9 not applicable for 6W Motor 50 100 150 200 250 300 400 6 25 40 60 90 NV (No Motor) NM (No Motor) NH (No Gearhead) R (No Motor, Gearhead) Belt Specification Standard Belt (Body Price Only) Optional Belt 1 Optional Belt 2 No Belt General Purpose H (Green), W (White) - - J (No Belt) For Sliding G (Green), S (White) - - For Inclined Transfer - - - Grip Type - - GG (Green), GW (White) Oil Resistant O (Green) OW (White) - Non-Stick Food Grade N (White) NB (Sky Blue), NBG (Lime Green) HH (Green), HW (White) - Food Grade - KW (White), KSB (Sky Blue), PHB (Sky Blue) - Static Conductive D (Black) - - EFor Flat Belt details, see P.1279~. Part Number - B - L - Motor - Belt Specification - Motor Manufacturer Selection Output - Voltage - Specification - Gearhead Reduction Ratio SVKR - 100 - 1000 - 25 - T100 - IM - 25 - H - C Configure Online * CE is not supported for widths of 300 and 400. CE Compliant Part Number B Available Sizes L390~ 400 L405~ 500 L505~ 600 L605~ 700 L705~ 800 L805~ 900 L905~ 1000 L1005 ~1100 L1105 ~1200 L1205 ~1300 L1305 ~1400 L1405 ~1500 L1505 ~1600 L1605 ~1700 L1705 ~1800 L1805 ~1900 L1905 ~2000 L2005 ~2200 L2205 ~2400 L2405 ~2600 L2605 ~2800 L2805 ~3000 SVKR 50 100 150 200 - 250 - - 300 - - - 400 - - - - *Reference Value may different by selected Belt. QGearhead Reduction Ratio Gearhead Reduction Ratio Belt Speed (m/min) 50Hz 60Hz 5 47.1 56.5 7.5 31.4 37.7 9 26.2 31.4 12.5 18.8 22.6 15 15.7 18.8 18 13.1 15.7 25 9.4 11.3 30 7.9 9.4 36 6.5 7.9 50 4.7 5.7 60 3.9 4.7 75 3.1 3.8 90 2.6 3.1 100 2.4 2.8 120 2.0 2.4 150 1.6 1.9 180 1.3 1.6 * May decrease depending on load condition. QConveying Capacity 6W / B=400 25W / B=400 40W / B=400 60W / B=400 90W / B=400 0 5 10 15 20 0 10 20 30 40 50 60 Belt Speed (m/min) Transfer Mass (kg/Unit) Output (W) Motor Reduction Ratio Motor Length (A) Specification Manufacturer 6W Constant Speed Motor Panasonic 5~25 101.0 30~180 108.0 Oriental 5~25 105.0 30~180 115.0 Taiwanese 5~75 114.7 90~180 120.7 Variable Speed Motor Panasonic 5~25 111.0 30~180 118.0 Oriental 5~25 115.0 30~180 125.0 Taiwanese 5~75 126.9 90~180 132.9 25W Constant Speed Motor Panasonic 5~180 115.0 Oriental 5~18 117.0 25~180 127.5 Taiwanese 5~75 129.0 90~180 136.0 Variable Speed Motor Panasonic 5~180 125.0 Oriental 5~18 127.0 25~180 137.5 Taiwanese 5~75 139.5 90~180 146.5 Motor Specifications Output (W) Motor Reduction Ratio Motor Length (A) Specification Manufacturer 40W Constant Speed Motor Panasonic 5~180 142.0 Oriental 5~18 147.0 25~180 165.0 Taiwanese 5~75 161.6 90~180 170.6 Variable Speed Motor Panasonic 5~180 152.0 Oriental 5~18 157.0 25~180 175.0 Taiwanese 5~75 172.1 90~180 181.1 60W Constant Speed Motor Panasonic 5~180 180.0 Oriental 5~180 185.0 Taiwanese 5~75 182.6 90~180 191.6 Variable Speed Motor Panasonic 5~180 210.0 Oriental 5~180 215.0 Taiwanese 5~75 194.6 90~180 203.6 90W Constant Speed Motor Panasonic 5~180 195.0 Oriental 5~180 200.0 Taiwanese 5~75 195.6 90~180 204.6 Variable Speed Motor Panasonic 5~180 232.0 Oriental 5~180 230.0 Taiwanese 5~75 209.6 90~180 218.6 SVKR *When L≥490, each slot has four (4) nuts inserted. When counterbores for inserting nuts are required, please specify in alterations. *1 When L≥2005, belt support rollers are mounted at these positions. E The dimensions in the diagram are for Belt Specification H (0.8mm thick.). Take note that belt thickness varies by Belt Specifications. For Belt Specifications, see P.1279. E The “Detail C” of the frame is used for pulley holder mounting. The nuts cannot be moved to this area. 6W Motor Type 33 33 A 3.2 25W, 40W, 60W, 90W Motor Type 250 62 15 65 Capacitor Attached for Single-Phase Constant Speed Motor Only 49.7 34.5 #80 25W Motor Type 40W, 60W, 90W Motor Type 250 62 18 62 50 41 Capacitor Attached for Single-Phase Constant Speed Motor Only #90 Frame Cross Section and Enlarged View 2.5 1.5 5 5.2 8.2 +0.5 0 B+40 (Frame Width) 3 (13) 29 Detail A 8 13 8 3 5 13 14 11.8 R5 Carrying Surface Side Detail A (for M5) +0.5 0 For B=50 EFor B=50, down facing slot is not provided. EFor B=200 and 250, *2 section thickness is 4mm. ECompatible with JIS standard hex nuts. (13) 8 8 29 B+40 (Frame Width) (B+10)/2 13 14 11.8 Carrying Surface Side 3* 2 13 15 R5 Detail A 3* 2 5 9 R5 +1 0 For B=100~250 For B=300 29 (13) 8 Detail A 8 22 18 14.5 R3 120 80 15 11 Ø4.2 9 3 R5 R5 100 11.8 14 5 3 3 15 85 340 15 80 120 For B=400 29 (13) 8 8 14.5 100 11.8 14 3 3 85 Detail A 22 80 15 15 15 15 18 15 Ø4.2 9 3 R5 R3 R5 35 440 5 35 80 50 120 120 11 50 L: Distance between Pulleys L+31.6 31.6 29 L/2 Ø30 B: Belt Width 1.3 (Belt Upper Surface) 20 20 B+40 3.2 A 15.8 32.5 15.8 18 B+46 250 70 144.5 10 62 Ø30 Belt Support Roller *1 Ø28.6 L/4 Ø50 30.5 39.5 Capacitor Attached for Single-Phase Constant Speed Motor Only #60 Direction of Conveyance 33 Ø30 Ø30 Belt Support Roller *1 Detail C Detail C 30 30 For details of alterations, see w P. 1264. Specify Drive Section Position Additional Counterbores Roller Edge Motor Cover with Window Brackets for Speed Controller Included Post-Assembly Insertion Nuts Included Motors with Electromagnetic Brake Stands (Legs) Conveyor Resource Site: http://www. misumiusa.com/conveyor/ Conveyor selection, Design your own kit, & Maintenance parts search.
Transcript of C 1203-1204 F17-08 USA · 2019. 2. 25. · 1 -1203 1 -1204 Guided Flat Belt Conveyor SV Series...
-12031 -12041-12031 -12041
Guided Flat Belt Conveyor SV SeriesGuided Belt to Prevent Lateral Movement, Center Drive, 2-Groove Frame (Pulley Dia. 30mm)
Q Features: Streamlined structure has achieved the low cost. The center drive section is adjustable. The conveyor maintains good running straightness by the use of the guided belt to prevent lateral movement.
Frame Motor Cover1
Motor Cover2
Pulley Holder
MMaterial Aluminum Aluminum Low Carbon Steel AluminumSSurface Treatment Clear Anodize Paint Paint Paint
EIn case of selectiong Optional Belts, please select motor manufacturer A or B (Motor C is applicable for Standard Belt only.)
EConnect the motor so that the belt rotates in the direction of conveyance. For connection diagram, and details of motor and inverter, see wP. 1267.EWhen "No motor, gearhead" is selected, the motor mounting hole pitch will vary depending on the motor's power rating. Please see Technical Information in our Conveyor Selection web site for the dimension details.EWhen "No motor, gearhead" is selected, this unit will be delivered unassembled. The customer is to assemble the unit according to the included assembly instructions. See our Conveyor Selection site for assembly procedures and packaging details.ENote that warpage might occur in belts with the guided belt depending on the number of plies (thickness).
Part Number
Width B (mm)
Selection
Length L5mm
Increment
MotorBelt Specification
Motor Manufacturer Selection
EPrices vary by manufacturer.Output (W) Voltage (V) Specification Gearhead Reduction Ratio
SVKR
50100150200250
390~3000
625406090
(Single-Phase)TA100
TA110 TA115T200 TA200
TA220 TA230
IM(Constant Speed Motor)
SCM(Variable Speed Motor)
51860150
7.52575180
93090
12.536100
1550120
H (General Specifications, Green)W (General Specifications, White)
G (For Sliding, Green)S (For Sliding, White)
D (Static Conductive)O (Oil Resistant, Navy Blue)N (Non-Stick Food Grade, White)
J (No Belt)
* For belts other than the above, select from Belt Specification below.
A (Panasonic Motor)B (Oriental Motor)C (Taiwanese Motor)
25406090
(Three-Phase)SA200
SA220 SA230
IM (Constant Speed Motor)
INV (Induction Motor + Inverter)
300400
406090
(Single-Phase)TA100
TA110 TA115T200 TA200
TA220 TA230
IM(Constant Speed Motor)
SCM(Variable Speed Motor)
(Three-Phase)SA200
SA220 SA230
IM (Constant Speed Motor)
INV (Induction Motor + Inverter)
X5~9 not applicable for 6W Motor
50 100 150200 250300 400
625406090
NV (No Motor) NM (No Motor) NH (No Gearhead) R (No Motor, Gearhead)
Belt Specification Standard Belt (Body Price Only) Optional Belt 1 Optional Belt 2 No Belt
General Purpose H (Green), W (White) - -
J(No Belt)
For Sliding G (Green), S (White) - -
For Inclined Transfer - - -
Grip Type - - GG (Green), GW (White)
Oil Resistant O (Green) OW (White) -
Non-Stick Food Grade N (White) NB (Sky Blue), NBG (Lime Green)HH (Green), HW (White) -
Food Grade - KW (White), KSB (Sky Blue), PHB (Sky Blue) -
Static Conductive D (Black) - -
EFor Flat Belt details, see P.1279~.
Part Number - B - L -
Motor- Belt
Specification -Motor
Manufacturer SelectionOutput - Voltage - Specification - Gearhead
Reduction RatioSVKR - 100 - 1000 - 25 - T100 - IM - 25 - H - C
Con�gure Online
* CE is not supported for widths of 300 and 400.
CECompliant
C_1203-1204_F17-08_USAC_1203-1204_F17-08_USA USA FINAL2_1st
Part Number B
Available SizesL390~
400L405~
500L505~
600L605~
700L705~
800L805~
900L905~1000
L1005~1100
L1105~1200
L1205~1300
L1305~1400
L1405~1500
L1505~1600
L1605~1700
L1705~1800
L1805~1900
L1905~2000
L2005~2200
L2205~2400
L2405~2600
L2605~2800
L2805~3000
SVKR
50100
150
200 -
250 - -
300 - - -
400 - - - -
*Reference Value may different by selected Belt.
QGearhead Reduction Ratio
Gearhead Reduction Ratio
Belt Speed (m/min)50Hz 60Hz
5 47.1 56.5
7.5 31.4 37.7
9 26.2 31.4
12.5 18.8 22.6
15 15.7 18.8
18 13.1 15.7
25 9.4 11.3
30 7.9 9.4
36 6.5 7.9
50 4.7 5.7
60 3.9 4.7
75 3.1 3.8
90 2.6 3.1
100 2.4 2.8
120 2.0 2.4
150 1.6 1.9
180 1.3 1.6
* May decrease depending on load condition.QConveying Capacity
6W / B=40025W / B=40040W / B=40060W / B=40090W / B=400
0
5
10
15
20
0 10 20 30 40 50 60Belt Speed (m/min)
Tran
sfer
Mas
s (k
g/Un
it)
Output(W)
Motor Reduction Ratio
Motor Length(A)Specification Manufacturer
6W
Constant Speed Motor
Panasonic5~25 101.0
30~180 108.0
Oriental5~25 105.0
30~180 115.0
Taiwanese5~75 114.7
90~180 120.7
Variable Speed Motor
Panasonic5~25 111.0
30~180 118.0
Oriental5~25 115.0
30~180 125.0
Taiwanese5~75 126.9
90~180 132.9
25W
Constant Speed Motor
Panasonic 5~180 115.0
Oriental5~18 117.0
25~180 127.5
Taiwanese5~75 129.0
90~180 136.0
Variable Speed Motor
Panasonic 5~180 125.0
Oriental5~18 127.0
25~180 137.5
Taiwanese5~75 139.5
90~180 146.5
Motor SpecificationsOutput
(W)Motor Reduction
RatioMotor Length
(A)Specification Manufacturer
40W
Constant Speed Motor
Panasonic 5~180 142.0
Oriental 5~18 147.025~180 165.0
Taiwanese 5~75 161.690~180 170.6
Variable Speed Motor
Panasonic 5~180 152.0
Oriental 5~18 157.025~180 175.0
Taiwanese 5~75 172.190~180 181.1
60W
Constant Speed Motor
Panasonic 5~180 180.0Oriental 5~180 185.0
Taiwanese 5~75 182.690~180 191.6
Variable Speed Motor
Panasonic 5~180 210.0Oriental 5~180 215.0
Taiwanese 5~75 194.690~180 203.6
90W
Constant Speed Motor
Panasonic 5~180 195.0Oriental 5~180 200.0
Taiwanese 5~75 195.690~180 204.6
Variable Speed Motor
Panasonic 5~180 232.0Oriental 5~180 230.0
Taiwanese 5~75 209.690~180 218.6
SVKR
* When L≥490, each slot has four (4) nuts inserted. When counterbores for inserting nuts are required, please specify in alterations.
*1 When L≥2005, belt support rollers are mounted at these positions.E�The dimensions in the diagram are for Belt Specification H (0.8mm thick.). Take note that belt thickness varies
by Belt Specifications. For Belt Specifications, see P.1279.E�The “Detail C” of the frame is used for pulley holder mounting. The nuts cannot be moved to this area.
6W Motor Type
250
62
15 65
CapacitorAttached for Single-Phase Constant Speed Motor Only
49.7
34.5
3333A
3.2
#80
25W, 40W, 60W, 90W Motor Type
250
62
15 65
CapacitorAttached for Single-Phase Constant Speed Motor Only
49.7
34.5
3333A
3.2
#80
25W Motor Type
40W, 60W, 90W Motor Type
250 6218
6250
41
CapacitorAttached for Single-Phase Constant Speed Motor Only
#90
Frame Cross Section and Enlarged View
(13)
88
29
B+40 (Frame Width)
(B+10)/213
1411.8
2.5 1.55
5.2
8.2
+0.
50
Carrying Surface Side
3*2
13
15
R5
Detail A
3*2
5
9
R5
B+40 (Frame Width)
3
(13)29
Detail A
8
13
8
3
5
13
1411.8
R5
Carrying Surface Side
Detail A (for M5)
+0.50
+1 0
For B=50
EFor B=50, down facing slot is not provided.EFor B=200 and 250, *2 section thickness is 4mm.ECompatible with JIS standard hex nuts.
(13)
88
29
B+40 (Frame Width)
(B+10)/213
1411.8
2.5 1.55
5.2
8.2
+0.
50
Carrying Surface Side
3*2
13
15
R5
Detail A
3*2
5
9
R5
B+40 (Frame Width)
3
(13)29
Detail A
8
13
8
3
5
13
1411.8
R5
Carrying Surface Side
Detail A (for M5)
+0.50
+1 0
For B=100~250
For B=300
29
(13)
8
Detail A
8
22 1814.5 R3
120
8015
11
Ø4.2 93
R5 R5
100
11.814
533
1585
340
1580
120
For B=400
29
(13)
8
8
14.5
100
11.814
3
3
85
Detail A22
80
15 15 15 1518
15
Ø4.293
R5
R3
R5
35
440
5
35 80
50 120120
11
50
L: Distance between Pulleys
L+31.6
31.6
29L/2
Ø30
B: B
elt W
idth
1.3 (B
elt Up
per S
urfac
e)20
20
B+40
3.2
A
15.8
32.5
15.8
18
B+46
25070
144.
5
10
62
Ø30Belt Support Roller *1
Ø28.6
L/4
Ø50
30.5
39.5
CapacitorAttached for Single-Phase Constant Speed Motor Only
#60
Direction of Conveyance
33
Ø30
Ø30
Belt Support Roller *1
Detail C Detail C30 30
For details of alterations, see wP. 1264.
Specify Drive Section PositionAdditional Counterbores
Roller EdgeMotor Cover with Window
Brackets for Speed Controller IncludedPost-Assembly Insertion Nuts IncludedMotors with Electromagnetic Brake
Stands (Legs)
Conveyor Resource Site: http://www.misumiusa.com/conveyor/Conveyor selection, Design your own kit, & Maintenance parts search.
![[XLS]cindasdata.com · Web viewMaterial_Cross_Index Material_Cross_Index MCode and MName 1103, Carbon Steel T-1 1201, High Strength Steel 4130 1203, High Strength Steel 4140 1204,](https://static.fdocuments.net/doc/165x107/5afc6e7e7f8b9a864d8c1ae5/xls-viewmaterialcrossindex-materialcrossindex-mcode-and-mname-1103-carbon.jpg)
