C 011 eadline3pt/1mm Compact Modules

C 01_1 Headline_36pt/14.4mmC 01_2 Subheadline_15pt/7.2mm

Compact Modules Catalog addition: Lubrication / Cover „Resist“

2

Bosch Rexroth AG, R999001350 (2017-03)

2

Catalog addition Lubrication

Compact Modules - catalog addition |


Identification system for short product names

Content

Short product name Example: C K K – 070 – NN – 1System = Compact Modules (C)Linear guide = Ball Rail System (K)Drive = Ball screw drive (K)

Toothed belt drive (R)

Size 070 / 090 / 110 / 145 / 200

Version = Standard version (N)

Generation = Product generation 1

Product description 4

Configuration 6CKK 6CKR 8

Lubrication 9Lube version LSS 9Lube version LPG 9Lube version LCF/LCO 10

Dimensional drawings 11

Lubricants 12

Product description 14

Configuration 15

Dimensional drawings 16

Operating conditions 18Further information 19Request/order form 20

Catalog addition Cover „Resist“

Service and information

333

Compact Modules CKK


| Compact Modules - catalog addition

Catalog addition Lubrication

, lubrication

Compact Modules CKR

4


44 Compact Modules – catalog addition, lubrication |


Product descriptionFurther development of the lubrication concept for Compact ModulesWith new options for various lubrication concepts, Bosch Rexroth is upgrading the product portfolio to follow the market trend.This catalog addition must always be used in conjunction with the “Compact Modules” main catalog.Please refer to the main catalog for all technical data such as dimensions, etc.

Two drive versions: ▶ Compact Modules CKK with Ball Rail System and ball screw drive ▶ Compact Modules CKR with Ball Rail System and toothed belt drive

Four different lube versions ▶ Standard lubrication (LSS) ▶ Preserved (LPG) ▶ Carriage with connection plate prepared for connection to one-point lubrication systems for liquid grease (LCF) ▶ Carriage with connection plate prepared for connection to one-point lubrication systems for oil (LCO)

Versions for oil and liquid grease lubrication prepared for connection to one-point lubrication systems ▶ High operational reliability through automated relubrication ▶ Need-based maintenance reduces consumption of lubricant, while ensuring high availability ▶ More degrees of freedom as lubrication is dependent on position and mounting location ▶ Low-cost unmanned maintenance

Notes on the lube version

LSS: ▶ Initial lubrication by Bosch Rexroth ▶ Relubrication using manual grease gun

LPG: ▶ Ball Rail System and ball screw drive ▶ Relubrication using manual grease gun ▶ Basic lubrication required

LCF: ▶ Prepared for connection to one-point lubrication systems for liquid grease (NLGI grade 00 in accordance with DIN 51818) ▶ Lubrication with liquid grease only via single-line piston distributor system ▶ Basic lubrication required

LCO: ▶ Prepared for connection to one-point lubrication systems for oil ▶ Oil lubrication only via single-line piston distributor system ▶ Runner block and ball screw drive nut with integrated non-return valves ▶ Basic lubrication required

Product description

555

Compact Modules CKKLube version LSS, LPG

▶ Grease lubrication with manual grease gun via frame, carriage or via connection plate

Compact Modules CKRLube version LSS, LPG

▶ Grease lubrication with manual grease gun via frame, carriage or via connection plate

Connection plates Connection plates

| Compact Modules – catalog addition, lubrication


Lube version LCF, LCO

▶ 3 lube fittings ▶ Prepared for connection to

one-point lubrication systems

Lube version LCF, LCO

▶ 2 lube fittings ▶ Prepared for connection to

one-point lubrication systems

Lube version LSS, see main catalog Lube version LSS, see main catalog

Product description

6




1) See Compact Modules main catalog for technical data

CKK

Size

1)

Lubr

icat

ion

Vers

ion

Line

ar g

uide

Drive

Screw support

Carriage

Motor attachment

Motor Cover Switching system

Documen-tation

Scre

w jo

urna

l BASA d0 x P Connection plate

8 x

2.5

12 x

2

12 x

5

12 x

10

16 x

5

16 x

10

16 x

16

20 x

5

20 x

20

25 x

10

20 x

40

32 x

5

32 x

10

32 x

20

32 x

32

wit

hout

dr

ive

Without With

Lca (mm) Option Lca

(mm) Option

CK

K-07

0

LPG

see

Com

pact

Mod

ules

mai

n ca

talo

g

Ø 6 mm 31 – – – – – – – – – – – – – – 50 – 73 302 95 341

see Compact Modules main catalog

CK

K-09

0 LPG

Ø 8 mm

33 31 32 – – – – – – – – – – – 50

– 100 302 125 341

–variable

min = 101 max = 235

305 – –

LCF– 03 01 02 – – – – – – – – – – – –

– – – 125 141

LCO – – – 125 241

CK

K-11

0 LPG

Ø 11 mm

– – – – 31 32 33 – – – – – – – – 50

– 124 302 155 341

–variable

min = 125 max = 289

305 – –

LCF– – – – 01 02 03 – – – – – – – – –

– – – 155 141

LCO – – – 155 241

CK

K-14

5

LPG

Ø 14 mm

– – – – – – –31 32 33 –

– – – –

50

– 149 302 190 341

– – – 34 307 309

– – – – – – –31 32 33 –

– – – – –variable

min = 150 max = 349

305 – –

– – – 34 310 – –

LCF – – – – – – –21 22 23 –

– – – – –– – – 190 141

– – – 24 – 109

LCO – – – – – – –21 22 23 –

– – – – –– – – 190 241

– – – 24 – 209

CK

K-20

0

LPG

Ø 16 mm

– – – – – – – – – – – 31 32 33 34

50 Without 254.5 311

– ––

1 312

2 313

3 314

50variable

min = 255.5 max = 429.5

318 – –

–

Without

– – 305

341

1 326

2 327

3 328

LCF – – – – – – – – – – – 01 02 03 04 –

Without

– – 305

141

1 126

2 127

3 128

LCO – – – – – – – – – – – 01 02 03 04 –

Without

– – 305

241

1 226

2 227

3 228

Configuration

777 | Compact Modules – catalog addition, lubrication


Size

1)

Lubr

icat

ion

Vers

ion

Line

ar g

uide

Drive

Screw support

Carriage

Motor attachment

Motor Cover Switching system

Documen-tation

Scre

w jo

urna

l BASA d0 x P Connection plate

8 x

2.5

12 x

2

12 x

5

12 x

10

16 x

5

16 x

10

16 x

16

20 x

5

20 x

20

25 x

10

20 x

40

32 x

5

32 x

10

32 x

20

32 x

32

wit

hout

dr

ive

Without With

Lca (mm) Option Lca

(mm) Option

CK

K-07

0

LPG

see

Com

pact

Mod

ules

mai

n ca

talo

g

Ø 6 mm 31 – – – – – – – – – – – – – – 50 – 73 302 95 341


CK

K-09

0 LPG

Ø 8 mm

33 31 32 – – – – – – – – – – – 50

– 100 302 125 341

–variable

min = 101 max = 235

305 – –

LCF– 03 01 02 – – – – – – – – – – – –

– – – 125 141

LCO – – – 125 241

CK

K-11

0 LPG

Ø 11 mm

– – – – 31 32 33 – – – – – – – – 50

– 124 302 155 341

–variable

min = 125 max = 289

305 – –

LCF– – – – 01 02 03 – – – – – – – – –

– – – 155 141

LCO – – – 155 241

CK

K-14

5

LPG

Ø 14 mm

– – – – – – –31 32 33 –

– – – –

50

– 149 302 190 341

– – – 34 307 309

– – – – – – –31 32 33 –

– – – – –variable

min = 150 max = 349

305 – –

– – – 34 310 – –

LCF – – – – – – –21 22 23 –

– – – – –– – – 190 141

– – – 24 – 109

LCO – – – – – – –21 22 23 –

– – – – –– – – 190 241

– – – 24 – 209

CK

K-20

0

LPG

Ø 16 mm

– – – – – – – – – – – 31 32 33 34

50 Without 254.5 311

– ––

1 312

2 313

3 314

50variable

min = 255.5 max = 429.5

318 – –

–

Without

– – 305

341

1 326

2 327

3 328

LCF – – – – – – – – – – – 01 02 03 04 –

Without

– – 305

141

1 126

2 127

3 128

LCO – – – – – – – – – – – 01 02 03 04 –

Without

– – 305

241

1 226

2 227

3 228

Configuration

8




CKRCarriage/

Connection plate

Size 1) Lubrica-tion

Version Linear guide

Drive Without with Motor attachment

Motor Switching system

Documen-tationLca

(mm)Option Lca

(mm)Option

CKR-070 LPG


108 302 95 341


CKR-090

LPG 156 302 125 341

LCF – – 125 141

LCO – – 125 241

CKR-110

LPG 215 302 155 341

LCF – – 155 141

LCO – – 155 241

CKR-145

LPG 240 302 190 341

LCF – – 190 141

LCO – – 190 241

CKR-200

LPG 405 302 305 341

LCF – – 305 141

LCO – – 305 2411) See Compact Modules main catalog for technical data

Configuration

999

Carriage without connection plate1)

Carriage with connection plate1)

Size CKK CKR

Lca (mm) Option Lca (mm) Option

070 95 341 95

341

090 125 341 125

110 155 341 155

145 190 309 / 341 190

200 305 326 / 327 / 328 / 341 305

Lca Lca

Size CKK CKRLca (mm) Option Lca (mm) Option Lca (mm) Option

070 73.0 302 – – 108

302

090 100.0 302

Variable

305 156

110 124.0 302 305 215

145 149.0 302 / 307 305 / 310 240

200 254.5 311 / 312 / 313 / 314 318 405

Lca Lca

LW

Lca



Lube version LPG

1) See Compact Modules main catalog for detail drawing and technical data

Lube version LSS ▶ see Compact Modules main catalog

Lube version

10


10

A

23

11

2

A

Carriage with connection plate1)

Compact Modules – catalog addition, lubrication |


Lube version LCF/LCO

Compact Modules CKK Compact Modules CKR

A Drive side1 Lube fitting, runner block left2 Lube fitting, runner block right3 Lube fitting, ball screw driveLube fittings: Straight connector (SW 9), for Ø4 mm plastic tubes and metal pipes.

1) See Compact Modules main catalog for detail drawing and technical data

Lube version

111111

LcaH6

H5

H5

Ø D

H8



CKK

Size Lube version option Dimensions (mm)

Lca LCF LCO H5 ⌀D H6 H8

(mm)

070 – – – – – – –090 125 141 241 38 8.5

12.5

3110 155 141 241 40 8.5 3145 190 141 241 52 0 0200 305 141, 126, 127, 128 241, 226, 227, 228 62 0 0

CKR

Size Lube version option Dimensions (mm)

Lca LCF LCO H5 ⌀D H6 H8

(mm)

070 – – – – – – –090 125 141 241 38 8.5

12.5

3110 155 141 241 80 8.5 3145 190 141 241 84 0 0200 305 141 241 84 0 0

Dimensional drawings


12




LubricantsLube version LSS LPG LCF LCOSize CKx-110, -145, -200 CKx-070, -090 CKx-110, -145, -200 CKx-070, -090 CKx-090, -110, -145, -200 CKx-090, -110, -145, -200Initial greasing Dynalub 510 Dynalub 520 Preserved, initial greasing required

(See instructions)required, see instructions required, see instructions

Consistency class NLGI 2 (DIN 51818) NLGI 00 (DIN51818) – NLGI 00 (DIN51818) –Identification KP2K-20 (DIN 51825) GP00K-20 (DIN 51826) – GP00K-20 (DIN 51826) –Lubrication with manual grease gun

yes yes yes – –

Prepared for connection to one-point lubrication systems – – –

• only via single-line piston distributor system• smallest permitted piston distributor size: CKx-090, -110, -145, -200: 0,2 cm3

• only via single-line piston distributor system• smallest permitted piston distributor size: CKx-090, -110: 0.2 cm3; CKx-145: 0.4 cm3; CKx-200: 0.6 cm3

Lubricant recommendation Dynalub 510 (grease lubri-cant)

(NLGI2 DIN 51818)

Dynalub 520 (liquid grease)

(NLGI00 DIN51818)

Dynalub 510 (grease lubri-cant)

(NLGI2 DIN 51818)

Dynalub 520 (liquid grease) (NLGI00 DIN51818)

Dynalub 520 (liquid grease)(NLGI00 DIN51818)

Shell Tonna S3 M220 (lubricant oil)

Properties • Good water resistance• Corrosion protection• Temperature range: –20 to +80 °C

• Good water resistance• Corrosion protection• Temperature range: –20 to +80 °C


• Special demulsifying oil CLP or CGLP as per DIN 51517-3 for machine bed tracks and tool guides• A blend of highly refined mineral base oils and additives• Can be used even when mixed with significant quantities of metalworking fluids

Material numbers R3416 037 00(Cartridge 400 g)

R3416 043 00(Cartridge 400 g)

R3416 037 00(Cartridge 400 g)

R3416 043 00(Cartridge 400 g)

R3416 043 00 (Cartridge 400 g)

–

R3416 035 00(Hobbock 25 kg)

R3416 042 00 (Bucket 5 kg)

R3416 035 00 (Hobbock 25 kg)

R3416 042 00 (Bucket 5 kg)

R3416 042 00(Bucket 5 kg)

–

Alternative lubricants • Tribol GR 100-2 PD• Elkalub GLS 135/N2

• Tribol GR 100-00 PD• Elkalub GLS 135/N00

• Tribol GR 100-2 PD• Elkalub GLS 135/N2• Tribol GR 100-00 PD• Elkalub GLS 135/N00• Dynalub 520



• Special demulsifying oil CLP or CGLP as per DIN 51517-3 for machine bed tracks and tool guides

Alternative lubricants with H1 approval – –

• Berulub FG H2 SL• Cassida Grease EPS2• VP 874

• Berulub FB 34-00• Elkalub GLS 367/N00 – –

c Notes on lubrication

▶ Follow the instructions for each product. ▶ Do not use lubricants containing solid particles (e.g. graphite or MoS2)! ▶ If you use different lubricants from the ones stated, you may find that relubrication intervals are shorter and that

performance decreases with short stroke and load ratio; in addition, chemical interactions can take place between the plastics, lubricants and the anti-corrosion agents. In addition, pumpability in single-line one-point lubrication systems must be guaranteed.

▶ If using a one-point lubrication system, you must make sure that all the pipes and elements are filled with lubricant and do not contain any air pockets until they are connected to the consumer (carriage).

▶ Pumping or storage tanks for the lubricant must be fitted with a stirrer to guarantee the flow of lubricant (to avoid funneling in the tank).

▶ In the case of relubrication, it is not possible to change from grease to oil lubrication or vice versa. ▶ In the case of environmental influences such as contamination, vibration, jolting, etc., we recommend shortening the

relubrication intervals appropriately. Even under normal operating conditions, the system must be relubricated at the latest after 2 years due to aging of the grease.

▶ Rexroth recommends piston distributors manufactured by SKF. These should be installed as close as possible to the lube fittings of the carriage. Long lines (maximum line length 1 m) and small line diameters should be avoided, and the lines should be laid on an upward slant. Install the lines at a gradient.

▶ If other consumers are connected to the single-line centralized lubrication system, the weakest link in the chain will determine the lubrication cycle time.

▶ Excess lubricant can accumulate inside of the Compact Module or flow out and may lead to contamination of the environment

▶ Never put a Compact Module into operation without basic lubrication.

Lubricants

131313 | Compact Modules – catalog addition, lubrication


Lube version LSS LPG LCF LCOSize CKx-110, -145, -200 CKx-070, -090 CKx-110, -145, -200 CKx-070, -090 CKx-090, -110, -145, -200 CKx-090, -110, -145, -200Initial greasing Dynalub 510 Dynalub 520 Preserved, initial greasing required

(See instructions)required, see instructions required, see instructions

Consistency class NLGI 2 (DIN 51818) NLGI 00 (DIN51818) – NLGI 00 (DIN51818) –Identification KP2K-20 (DIN 51825) GP00K-20 (DIN 51826) – GP00K-20 (DIN 51826) –Lubrication with manual grease gun

yes yes yes – –

Prepared for connection to one-point lubrication systems – – –

• only via single-line piston distributor system• smallest permitted piston distributor size: CKx-090, -110, -145, -200: 0,2 cm3

• only via single-line piston distributor system• smallest permitted piston distributor size: CKx-090, -110: 0.2 cm3; CKx-145: 0.4 cm3; CKx-200: 0.6 cm3

Lubricant recommendation Dynalub 510 (grease lubri-cant)

(NLGI2 DIN 51818)

Dynalub 520 (liquid grease)

(NLGI00 DIN51818)

Dynalub 510 (grease lubri-cant)

(NLGI2 DIN 51818)

Dynalub 520 (liquid grease) (NLGI00 DIN51818)

Dynalub 520 (liquid grease)(NLGI00 DIN51818)

Shell Tonna S3 M220 (lubricant oil)

Properties • Good water resistance• Corrosion protection• Temperature range: –20 to +80 °C



• Special demulsifying oil CLP or CGLP as per DIN 51517-3 for machine bed tracks and tool guides• A blend of highly refined mineral base oils and additives• Can be used even when mixed with significant quantities of metalworking fluids

Material numbers R3416 037 00(Cartridge 400 g)

R3416 043 00(Cartridge 400 g)

R3416 037 00(Cartridge 400 g)

R3416 043 00(Cartridge 400 g)

R3416 043 00 (Cartridge 400 g)

–

R3416 035 00(Hobbock 25 kg)

R3416 042 00 (Bucket 5 kg)

R3416 035 00 (Hobbock 25 kg)

R3416 042 00 (Bucket 5 kg)

R3416 042 00(Bucket 5 kg)

–

Alternative lubricants • Tribol GR 100-2 PD• Elkalub GLS 135/N2


• Tribol GR 100-2 PD• Elkalub GLS 135/N2• Tribol GR 100-00 PD• Elkalub GLS 135/N00• Dynalub 520



• Special demulsifying oil CLP or CGLP as per DIN 51517-3 for machine bed tracks and tool guides

Alternative lubricants with H1 approval – –

• Berulub FG H2 SL• Cassida Grease EPS2• VP 874

• Berulub FB 34-00• Elkalub GLS 367/N00 – –

c Use of lubricants with H1 approval:

Loss of H1 approvalH1 lubricants or separating agent (anti-corrosion agent) only have H1 approval if they are available by material type in unmixed condition (including at the lubrication point). A blend of two H1 approval lubricants or separating agents does not have H1 approval. No food industry authorization or approval

Because of the use of H1 lubricants, the Compact Modules do not have authorization or approval for the food industry.

Lubrication of components at the factoryComponents lubricated by the manufacturer at the factory such as deep-groove ball bearings, cover strips, gears, etc. do not use H1 lubricants.

c Compact Modules with Dynalub 520 (NLGI 00 class) initial greasing must not be pre-lubricated with lubricants of consistency class NLGI 2!

For relubrication quantity and relubrication position ⇒ see Compact Modules CKK/Compact Modules CKR instructions.Relubrication intervalWhen using the standard lubrication from the manufacturer:Relubrication interval⇒ see Compact Modules CKK/Compact Modules CKR instructions.Use of Dynalub 520 (NLGI00) instead of Dynalub 510 (NLGI2):The relubrication interval is 75% of the standard relubrication interval ⇒ CKK/CKR instructions.Use of lubricants with H1 approval:First relubrication takes place after 20 km. As a guideline value for relubrication intervals, 50% of the standard relubrication intervals must be applied ⇒ see Compact Modules CKK/Compact Modules CKR instructions.

Lubricants

14


14 Compact Modules – catalog addition, Cover |


Structural design: ▶ Compact Modules with ball screw drive (CKK) ▶ Sizes: CKK -110, -145, -200 ▶ With connection plate ▶ Cover „Resist“

Properties: ▶ Increased protection because of toothed sealing profile ▶ Integrated tape guide at the carriage provides perfect

toothing of the sealing profile ▶ Sealing profile made of FKM material ▶ PWIS free (paint-wetting impairment substances) ▶ Replaceable sealing profile ▶ Short term heat resistance of sealing profile up to 300°C ▶ Suitable for dry chip admission and handling of

components during welding applications

Product descriptionAdvanced lubrication options:

▶ Standard lubrication (LSS) ▶ Preserved (LPG) ▶ Carriage with connection plate prepared for connection to

one-point lubrication systems for liquid grease (LCF) ▶ Carriage with connection plate prepared for connection to

one-point lubrication systems for oil (LCO)

Catalog addition: Cover „Resist“

Strip clampsfor Sealing profile

Sealing profile made of FKM material

Connection plate

Tape guide

Brackets for Cover

Cover plate

Lube fittings forone-point lubrication systems1)

1) See chapter Lubrication

Thoothing sealing profile

Product description

151515 | Compact Modules – catalog addition, Cover


Size

Lubr

icat

ion1

)

Vers

ion

Gui

dew

ay

Dri

ve u

nit

Carriage withconnection plate

Mot

or a

ttac

hmen

t

Mot

or

Cover Switching system3)

Scre

wsu

ppor

t

L ca

(mm

)

Opt

ion

Cover strip

wit

hout

wit

h

Res

ist2

)

CK

K-11

0

LSS

see

Com

pact

Mod

ules

mai

n ca

talo

g

–

155

41

see

Com

pact

Mod

ules

mai

n ca

talo

g

012

LPG – 341

LCF – 141

LCO – 241

CK

K-14

5

LSS –

190

09

– 41

LPG – 309

– 341

LCF – 109

– 141

LCO – 209

– 241

CK

K-20

0

LSS without

305

41

1 26

2 27

3 28

LPG without 341

1 326

2 327

3 328

LCF without 141

1 126

2 127

3 128

LCO without 241

1 226

2 227

3 228

1) See chapter Lubrication2) Not tested with contact of dusts and cooling lubricants.

If you are unsure about using this product, please contact Bosch Rexroth. In the case of prolonged downtimes, a delayed resetting behavior of the sealing profile can occur in the area of the tape guide.

3) Switch mounting and accessories see Compact Modules main catalog 4) Only CKK-200

Without switch

000Without mounting duct

Without socket plug

Magnetic sensor with plug

REED sensor 058

HALL sensorPNP NC contact

059

Magnetic sensor4)

REED sensor 021

Hall-sensor - PNP NC contact 022

Hall-sensor-PNP-NO contact 023

Mounting duct 025

Socket plug 027

Configuration

Configuration

16


16 Compact Modules – catalog addition, Cover |


Size A B2 C H H11 H12 H13 Lca Z1

CKK-110 100 120 16 50 84 44 12 155 60.7

CKK-145 145 155 20 65 105 59 12 190 71.6

CKK-200 200 212 27 100 150 82 24 305 86.4


Z1 = application point of the effective force


171717 | Compact Modules – catalog addition, Cover


18


18 Compact Modules – catalog addition | Service and information


Normal operating conditionsAmbient temperature with Rexroth servo motor 0 °C ... 40 °C, above 40 °C loss of performance

Ambient temperature for mechanical system(No passing below the dew point) –10 °C ... 60 °C

Travel smin1) see Compact Modules main catalog

Contamination2) not permissible

Required and supplementary

documentationFor further instructions and information, please refer to documentation belonging to this product.

You can find PDF files of these documents in the Internet at www.boschrexroth.com/mediadirectory

We would also be pleased to send you the requested documents.

If you are unsure about using this product, please contact Bosch Rexroth.

Operating conditions

1) Minimum travel to ensure a reliable lubrication distribution.2) Cover „Resist“:

Suitable for dry chip admission and handling of components during welding applications. Not tested with contact of dusts and cooling lubricants.

www.boschrexroth.com/mediadirectory

191919

http://www.boschrexroth.com/goto

Service and information | Compact Modules – catalog addition


Further informationBosch Rexroth homepage: http://www.boschrexroth.com

Compact Modules product information: http://www.boschrexroth.com/en/xc/products/product- groups/linear-motion-technology/linear-motion-systems/compact-modules/index

GoTo Europe:

http://www.boschrexroth.com/goto

http://www.boschrexroth.com

https://www.boschrexroth.com/en/xc/products/product-groups/linear-motion-technology/linear-motion-systems/compact-modules/index



20


20

Company: Responsible person: Address: Department: Telephone: Fax:

QuantityComments:

From

Acceptance of: _____ pcs, ______ per month, _______ per year, per order, or ________________________

1) Only required for carriage options with variable centerline-to-centerline distance. 2) Only required for “Mounting kits for motors according to customer specification”.

Compact Modules – catalog addition | Service and information


Rexroth – Compact Modules

Find your local contact person here:www.boschrexroth.com/addressen

Request/order form

Ordering exampleOrdering data Option Explanation from catalogCompact Module(short product name)

CKK-110-NN-1,715 mm

CKK-110 Compact ModulesLength = 715 mm (1500 max.)

A(main catalog)

Version MF01 Flange/coupling for motor attachment acc. to illustration MF01Linear guide 01 Standard frameDrive 02 Ball screw drive 16 x 10Carriage 141 Carriage with connection plate for one-point

lubrication system for liquid grease (LCF), Lca = 155 mmB

(this catalog)Motor attachment 01 Flange/coupling for MSK 030C motor A

(main catalog)Motor 85 MSK 030C motor with brake

Cover 02 With cover „Resist“B

(this catalog)

1. Switch 21 REED sensor (delivered as separate part)

A(main catalog)

2. Switch 22 HALL sensor, PNP NC (delivered as separate part)3. Switch 21 REED sensor (delivered as separate part)Mounting duct / cable duct 25 Mounting duct (delivered as separate part)Socket plug 17 Socket-plug, loose (delivered as separate part)Documentation 01 Standard report

212121Service and information | Compact Modules – catalog addition


A

B

22


22 Compact Modules – catalog addition, lubrication | Notice


232323Notice | Compact Modules – catalog addition, lubrication


Find your local contact person here:www.boschrexroth.com/contact

Bosch Rexroth AGErnst-Sachs-Straße 10097424 Schweinfurt, GermanyTel. +49 9721 937-0 Fax +49 9721 937-275www.boschrexroth.com

R999001350 (2017-03)© Bosch Rexroth AG 2017Subject to changes!

The data specified above only serves to describe the product.Since our products undergo continuous further development, no statement regarding any particular quality or suitability for any particular use can be derived from this information. The information does not release the user from making his/her own inspections and evaluations. It must be remembered that our products are subject to a natural process of wear and aging.

C 011 eadline3pt/1mm Compact Modules

Documents

Transcript of C 011 eadline3pt/1mm Compact Modules