Transport Expert

DSn (T-carrier) & Ethernet network testing simplified VeEX™ VePAL TX130+ is a next generation test solution for DSn and PDH networks transporting legacy and next generation services for Ethernet and IP testing.

VePAL TX130+Handheld DSn/PDH and Ethernet Test Set

Platform Highlights

• Intuitive presentation of measurements with test graphics • High resolution color touch-screen viewable in any lighting

conditions fitted with protective cover• Robust, handheld chassis packed with powerful and flexible

features for demanding environments and test conditions• Optimized for field engineers or technicians installing and

maintaining transporting legacy network• Ethernet port and connection for back office applications,

workforce management and triple play service verification• User defined test profiles and thresholds enable fast, efficient

and consistent turn-up of services• USB memory stick support and FTP upload capability for test

result storage and file transfer respectively• Maintain instrument software, manage test configurations,

process measurement results and generate customer test reports using included ReVeal™ PC software

• Extend field testing time using interchangeable LiIon battery pack/s. Greater battery autonomy provided in standby mode

• Supports advanced IP testing; Ping, trace route, ARP Wiz, VoIP, IPTV, web browser, and FTP upload/download via Ethernet or USB port where applicable

• Perform remote testing and monitoring using the remote control option via standard Ethernet interface

Key Features

• Supports DS1, DS3 bit rates; PDH E1, E2, E3 Optional• Balanced (100Ω) and Unbalanced (75Ω) interfaces for DS1 • Dual DS1 Transmitters & Receivers • Dual Rx port DS3 • Full Rate DS1 and Fractional N, Nx64 kbit/s or Nx56 kbit/s

testing• Non intrusive Pulse Mask Analysis at DS1 and DS3 bit rates* • Level and Frequency measurements • Auto Configuration of network type, bit rate, line coding

framing, and test pattern • Bit Error and Performance Analysis per ITU/Bellcore standards • Error and Alarm Generation and Analysis • Histogram and Event analysis for errors and alarms • Round Trip Delay on all interfaces • Transmit Frequency Offset to stress clock recovery circuits • DS1 and DS3 Loop capability• 10/100/1000-T Ethernet Testing for BERT, Throughput,

Loopback and RFC2544 in single stream*• VF drop/insert by headset*- Optional• VF frequency/level measurement and VF send tone*• ISDN PRI (ANSI and ETSI) call set up* • Jitter analysis on all rates*

*Optional

APPLICATIONS

DSn Alarm Monitoring

DS1

DS3 45Mb/s1.5Mb/s

ProtectedMonitoringPoint (PMP)

Applications

Transmission Testing The TX130+ is perfectly suited for both in-service and out-of-service measurements on DSn (T-Carrier) networks. Out-of-service testing usually applies to the installation, commissioning and the “bringing into service” measurements needed to qualify a digital transmission link using industry standard test patterns and methods. In-service testing is an important, ongoing maintenance task - field technicians can monitor PCM signals for errors, alarms, level, frequency and pulse shape to prevent service degradation. The transmitter and receiver can be configured independently to perform MUX tests and round trip delay measurements are possible at various points across the network using any of the test interfaces.

Mobile Backhaul Testing Mobile operators confronted with the explosive growth of data-centric services driven by 3G and LTE Smartphone applications, are urgently upgrading and migrating traditional TDM backhaul networks to Ethernet/IP packet-based technologies. The TX130+ tester equipped with a hybrid of interfaces and applications is perfectly equipped to test both DSn (T-Carrier) and IP transport over copper and fiber backhaul connections across the Radio Access Network (RAN).

Performance Analysis SummaryThe summary screen displays Pass/Fail criteria for each major parameter. A large color coded message informs or alerts the technician of the circuit’s status. The Analysis tab reports test performance per ANSI, Bellcore or ITU-T recommendations.

Errors and AlarmsBER testing is commonly used to verify continuity across a digital link, to check for faults, and for performing acceptance tests.Equipped with an extensive range of test patterns including the ability to inject errors in the pattern, framing and alarm bits, the TX130+ quickly evaluates circuits and examines error responses. Anomalies (errors) and defects (alarms) are clearly displayed and recorded for each network segment, and are logged for further analysis.

DSn (T-Carrier)DSn (T-Carrier) Features

Advanced Mode

Quick and Easy Graphical SetupComplex daily tasks are common in today’s network environment, so technicians need a tester that is easy to configure and which doesn’t require extensive product training beforehand.

The test interface, signal structure, and test pattern setups are structured logically ensuring quick and efficient configuration. An intuitive graphical menu and a list of shortcuts provides fast access to commonly used DSn or PDH test functions boosting productivity.

Physical Layer TestingPrior to performing digital measurements, technicians should confirm analog parameters fall within prescribed limits.

Clock tolerances for each signal hierarchy defined by ITU-T and ANSI recommendations can easily be verified.

Incorrect pulse shape is a result of excessive cable length, impedance mismatch, or poor transmitter design. The G.703 pulse mask option quickly identifies related problems.

Data integrity in plesiochronous networks depends largely on the phase stability of clock and data signals, therefore excessive jitter can cause network outages. Because BER testing is the common method to diagnose network problems in the field, results often mislead the technician because only the effect of a problem and not the actual cause is reported. Ultimately, this makes fault identification more difficult, time consuming, and expensive.

The jitter software option of the TX130+ uses advanced digital measurement techniques for measuring intrinsic jitter, allowing technicians to easily determine when jitter is the source of errors.

Jitter MetricsOutput jitter performance mandated by ITU-T and Telcordia standards is evaluated by measuring the recovered clock of the incoming signal (DS1, DS3, E1, E3) traversing the network.

While the test duration is not defined in the mentioned standards, a measurement period time of 1 minute is recommended. Specified in unit intervals (UI), the maximum Peak-to-Peak Jitter is the most important parameter because Max values are indicative of performance, as these extremes generally cause errors. While jitter is defined as any phase variations above 10Hz, the incoming signal must be filtered in order to measure jitter – the user is therefore able to select between Wide band and High band filters to adjust the measurement bandwidth as required.

Jitter Measurements

ISDN/VF TESTINGJITTER

The ISDN option provides key functionality necessary for testing and troubleshooting T1 or E1 Primary Rate connections. Operating in TE or NT modes, the unit is able to setup and receive ISDN calls with user-defined parameters including call control protocol, called number and related facilities.

Protocol functions feature detailed signaling statistics, message monitoring and decode, and complete result presentation. With these capabilities, analysis of international and national ISDN, and other access protocols is possible.

The Voice Frequency (VF) option is a basic diagnostic tool to install, verify and troubleshoot voice circuits. Digital to analog conversion tests are performed by inserting/measuring tones with user defined frequency and level on selected sub-rate channels.

A microphone/headset adaptor enables Talk/listen capability on a selected timeslot whilst a powerful function allows VF decoding at all DSn/PDH rates.

ISDN Testing VF Testing

The Ping over WAN option verifies IP service across T1 or E1 interfaces. The TX130+ can replace a customer router, modem, or Integrated Access Device (IAD) in order to check IP connectivity with a local or remote end point by transmitting and responding to ICMP echo requests (PINGs).

However before any layer 3 protocol can traverse the WAN using a dialup or dedicated leased line, it must be encapsulated by a data-link layer protocol. Depending on test application and interface, the technician can encapsulate the IP packets using either:

• PPP over HDLC• Ethernet over HDLC

Both static and DHCP connection modes are supported, and the user can determine the IP address and number of Pings to send.

Ping Test over WANPING over WAN

ETHERNETEthernet Features

Intelligent Network/Device DiscoveryEasily discover and select another TX130+, MX100+ tester or MLX100 on the network under test for loopback testing applications. The local device will control the operation of the far end device, in either loopback or peer-to-peer mode. This feature greatly simplifies field testing since there is no need for a second technician to be at the far end configuring the test partner device.

RFC2544 Compliance TestingPerforms the RFC2544 automated test suite at all recommended frame sizes including user configurable frame sizes and up to full line rate. The test suite can also be performed with the far end test partner in loopback mode or peer-to-peer mode - the latter allowing for symmetrical/asymmetrical testing. Thresholds may be configured for accurate SLA assurance and verification. The automated tests supported are throughput, latency, frame loss, and back-to-back frames.

BERT Layer 1, 2, 3, and Layer 4 BER testing is supported. The BER test can be configured to use regular PRBS test patterns, stress patterns or user defined test patterns to simulate various conditions. All patterns are encapsulated into an Ethernet frame to verify bit-per-bit performance of circuit under test.

One traffic stream is transmitted across the network under test and bit-per-bit error checking is then performed on the received traffic. Service disruption measurements as well as CRC error checking are also performed. The BER test can be performed with a physical loop (or plug) at the far end (for a layer 1 circuit), or a second test unit or intelligent loopback device in Smart Loop or in Peer-to-Peer mode.

Throughput TestA single traffic stream can be configured with CoS (VLAN priority) and QoS (TOS/DSCP) prioritization to facilitate end-to-end performance verification. The throughput test may be performed with a second test unit at the far end in Smart Loop mode or Peer-to-Peer mode.

Media ConvertersOptical interface testing using VeEX media convertersThe MC100 is a rate-switching 10/100 UTP copper to 100BASE-FX fiber media converter providing cost-effective connectivity between the TX130+ and 100 Mbit/s legacy fiber based networks.

The MC1000 is a miniature 1000BASE-T UTP copper to 1000BASE-X fiber Gigabit Ethernet media converter supporting connectivity from Gigabit switches and other devices such as computers.

Both media converters employ Small Form Pluggable (SFP) Transceivers to support different fiber types, data rates and distances. They can be powered by an external 5 Volt AC power supply or directly from the USB port on the TX130+ unit.

IEEE 802.3ah OAM SupportEthernet in the First Mile (EFM) OAM discovery and loopback controls are supported. This feature allows for the discovery of IEEE 802.3ah OAM-enabled devices and the ability to loopback these devices.

MPLS MeasurementsMultiple Protocol Label Switching (MPLS) is a technology that allows for a more efficient routing of Ethernet/IP packets via the use of MPLS routers in the network. MPLS labels reside between the MAC (Layer 2) and IP layers (Layer 3). Up to three MPLS tags can be configured in the traffic stream with user configurable Label, CoS, and TTL fields.

Q-in-Q (VLAN stacking)For Metro and Carrier Ethernet applications, VLAN stacking, also known as Q-in-Q, is supported. This feature makes a provision for carrier/service provider assigned VLANs, but also retains the VLAN of customer traffic.

Smart LoopbacksFour modes are available for looping back test traffic. At Layer 1, all incoming traffic is looped back unaltered. For Layer 2, all incoming unicast traffic is looped back with the MAC source and destination addresses swapped. For Layer 3, all incoming unicast traffic is looped back with the MAC and IP source and destination addresses swapped, and for Layer 4, all incoming unicast traffic is looped back with the MAC, IP, and UDP/TCP ports swapped.

Ethernet Features cont’d

Test Port StatusAuto-negotiation is a function that enables Fast Ethernet devices to automatically exchange information over a link about speed and duplex abilities. A common cause of performance issues on 10/100T Ethernet links occurs when one port on the link operates at half-duplex while the other port operates at full-duplex.

The port status feature of the TX130+ reports the auto-negotiation and link advertisement parameters of both test set and link partner, which helps to reduce many link performance-related support calls.

Delay and Jitter MeasurementsFrame delay and Jitter measurements are supported. Jitter measurements are based on RFC3393 which describes the industry recognized Inter Packet Delay Variation (IPDV) method.Jitter measurements are performed on the test traffic during BER tests or throughput tests.

IP/IPTV TESTINGIP Testing

Used initially only for Local Area Network (LAN) connectivity within the enterprise, the Internet Protocol (IP) has quickly grown to be the de-facto standard for multi-service network transport.

For Telco and IT technicians, it’s no longer enough to validate equipment at the physical interface or connection protocol level only, so IP testing has become a routine task during service installation and restoration.

The TX130+ supports an array of IP test functions over the 10/100/1000BaseT port including Ping, Trace Route and Triple Play measurement tasks. Web browsing, FTP throughput, VoIP and IPTV tests can be performed at various points in the network to ensure customer satisfaction.

IPTV Service Verification

Facing the growing challenge from competition in the cable television and wireless mobile industries, traditional telco’s are fast deploying IPTV to reduce customer churn in order to preserve revenues. As a consequence, technicians normally assigned to take care of leased line and datacom services are now being called upon to make IPTV measurements in order to reduce expensive truck rolls.

Although IPTV testing can be a complicated and daunting task, the TX130+ has been equipped with a good balance of user friendly functions needed to install and troubleshoot IP video service.

• Set-Top Box (STB) emulation offers registration, IGMP and RTSP signaling for Broadcast and Video on Demand (VOD) applications. • Transport stream analysis encompasses data/video/audio bit rates and Program Identification (PID) mapping. • Packet jitter and loss, IGMP latency (channel zapping), PCR and MDI statistics including a Viewer function provide valuable Quality of

Service (QoS) and Quality of Experience (QoE) metrics.

LocalNetwork

PublicNetwork

LocalNetwork

GTWY

VoIP Testing

Take advantage of the three software options offering different test methods to verify and provision your VoIP network. Testing can be performed over any of the Ethernet test ports.

VoIP Check – Simulates a VoIP call to the nearest router and measures the round trip MOS score and related VoIP parameters.

Net Wiz

Ethernet network installation is simplified using this basic, yet powerful feature. A built-in TDR identifies distance to short, distance to open, wire cross, and other anomalies associated with CAT-5 structured cabling. “Sniff” the network using the one-touch discovery feature. Identify routers, gateways, printers, PCs and other devices connected to the network within seconds.

VoIP/NET WIZ

VoIP Expert – Generates industry standard wave files to verify MOS and R-Factor values of upstream and downstream paths and includes QoS measurements such as packet jitter, packet loss, and delay. Compatible with all VeEX testers including VX1000 VoIP server software.

VoIP Call Expert – Emulates an IP phone and can place and receive calls using SIP or H.323 protocols. Comprehensive Codec support and call destination options verify voice encoding and translation provisioning. Real-time evaluation of subjective voice quality is made possible using the Telchemy test method.

DSn (T-Carrier)Electrical Interfaces Dual Bantam (100Ω balanced) Rates and Line code

• 1.544 Mbit/s, AMI & B8ZS • 2.048 Mbit/s, HDB3 & AMI (Optional)

BNC (75Ω unbalanced) Rates and Line code• 2.048 Mbit/s, HDB3 & AMI (Optional) • 8.448 Mbit/s, HDB3• 44.736 Mbit/s, B3ZS (Optional) • 34.368 Mbit/s, HDB3 (Optional)

Compliant to ITU-T G.703, G.823, G.824, G.772 and ANSI T1.102 recommendations where applicable

Clock recovery (pulling range) per ITU-T G.703 Receiver Sensitivity For 1.544 Mbit/s (DS1)

• Terminate: ≤ 6dB (cable loss) • Monitor (PMP): ≤ 26dB (20dB resistive, 6dB cable loss)• Bridge: ≤ 6dB (cable loss)

For 44.736 Mbit/s (DS3)• Terminate: ≤ 12dB (cable loss) • Monitor (PMP): ≤ 26dB (20dB resistive, 6dB cable loss)

Optional For 2.048 Mbit/s (E1)

• Terminate: ≤ 6dB (cable loss) • Monitor (PMP): ≤ 26dB (20dB resistive, 6dB cable loss) • Bridge mode: ≤ 6dB (cable loss)

For 8.448 Mbit/s (E2)• Terminate: ≤ 6dB (cable loss) • Monitor (PMP): ≤ 26dB (20dB resistive, 6dB cable loss)

For 34.368 Mbit/s (E3) • Terminate: ≤ 6dB (cable loss) • Monitor (PMP): ≤ 26dB (20dB resistive, 6dB cable loss)

Clock Synchronization Internal: ± 3.5 ppm stability per ITU-T G.812 Recovered: from the incoming signal External reference via RX2 balanced and BNC unbalanced

• Signal: 1.544 Mbit/s (B8ZS), 2.048 Mbit/s (HDB3)Tx Frequency Offset

• Up to 50 ppm in steps of 0.1 ppm for both optical and electrical interfaces

FunctionsOperating Modes Terminate, Monitor, Intrusive Thru mode Bridge (DS1 & E1)

Signal Structure 1.544 Mbit/s (DS1)

• Unframed or Framed SF (D4), ESF per ANSI and Telcordia standards where applicable

• Test signal in N x 64 kbit/s, N x 56 kbit/s where N=1 to 24 Optional 2.048 Mbit/s (E1)

• Unframed or Framed with/without CRC per ITU-T G.704 (PCM30, PCM30C, PCM31, PCM31C)

• Test signal in N/M x 64 kbit/s where N=1 to 30 8.448 Mbit/s (E2)

• Unframed or Framed per ITU-T G.74234.368 Mbit/s (E3)

• Unframed or Framed according to ITU-T G.75144.736 Mbit/s (DS3)

• Unframed or Framed M13 and C-Bit Parity

Patterns The following test patterns can be generated

• PRBS: 211-1, 215-1, 220-1, 223-1, 231-1: normal or inverted • Fixed: 0000, 1111, 1010, 1000 and 1100 • User programmable word: user defined up to 32 bits

Errors Insertion

• 1.544 Mbit/s (DS1): Code, FAS, Bit, Frame, CRC Optional

• 2.048 Mbit/s (E1): Code, FAS, CRC, EBIT, Bit errors • 8.448 Mbit/s (E2): Code, FAS, 2M FAS, 2M, Bit errors• 34.368 Mbit/s (E3): Code, FAS, 2M FAS, 2M, Bit errors • 44.736 Mbit/s (DS3): Code, FAS, MFAS, P/C-Parity, Bit errors• Single or continuous rate (1 x 10-3 to 5 x 10)

Measurement • 1.544 Mbit/s (DS1): Code, FAS, Bit, Frame, CRC • 44.736 Mbit/s (DS3): Code, FAS, MFAS, P/C-Parity, Bit errors

Optional (E1, E2, E3, DS3) – where applicable • Code, FAS, MFAS, 2M CRC, P/C-Parity, Bit errors

Alarms Generation

• 1.544 Mbit/s (DS1): AIS, yellow, idle, LOS, LOF • Mode: Static (Enable/Disable)

Optional • 2.048 Mbit/s (E1): LOS, AIS, LOF, RDI • 8.448 Mbit/s (E2): LOS, AIS, LOF, RDI, 2M LOF, 2M RDI• 34.368 Mbit/s (E3): LOS, AIS, LOF, RDI, 2M LOF, 2M RDI• 44.736 Mbit/s (DS3): LOS, LOF, OOF, AIS, Parity

Measurement • 1.544 Mbit/s (DS1): LOS, AIS, LOF, AIS, yellow, idle and LSS • 44.736 Mbit/s (DS3): LOS, AIS, LOF, Parity and LSS

Optional (E1, E2, E3) – where applicable • LOS, AIS, LOF, OOF, RDI and LSS

Measurement Functions

Test Results Error count, ES, %ES, SES, %SES, UAS, %UAS, EFS, %EFS, AS, %AS, and rate for all events: errors, alarms and pointer events

Performance Analysis Measurements according to:

• ITU-T G.821 recommendation: ES, EFS, SES and UAS with HRP 1% to 100%

• ITU-T G.826 recommendation: EB, BBE, ES, EFS, SES, UAS; HRP of 1% to 100%

• In service measurement (ISM) using FAS, CRC or Code (DS1 or E1

• Out of Service measurement (OOS) using bit errors (TSE) • ITU-T M.2100 recommendation: ES, EFS, SES, UAS with HRP

1% to 100% • User defined thresholds for Maintenance (MTCE) and Bringing

into Service (BIS) objectives• User defined thresholds for Maintenance (MTCE) and Bringing

into Service (BIS) objectives. In service measurements on both near and far ends of path using TSE

SPECIFICATIONS

Ethernet Electrical Interfaces Single 10/100/1000 Base-T Ports RJ45 connector IEEE 802.3 compliant Ethernet Features Auto Negotiation Full and Half Duplex Flow Control Modes of Operation Terminate Monitor Pass through Loopback Traffic Generation IEEE 802.3 and Ethernet II (DIX) framesConfigurable MAC, Ethernet Type, VLAN, MPLS, IP, and UDP header

fieldsConstant, Ramp, and Burst traffic profiles with configurable

bandwidth % utilizationJumbo Frame Support (8,000 bytes) Fixed, multiple, and random frame size generation Traffic prioritization via VLAN priority field, MPLS CoS field and the

IP TOS/DSCP fieldsUp to 3 VLAN and MPLS tags can be added to each user configured

traffic stream

RFC2544 Compliance Testing Automated tests with configurable threshold values and maximum

transmit bandwidth settingsThroughput, Latency, Frame Loss, and Back-to-back (burst) testsFrame sizes: 64, 128, 256, 512, 1024, 1280, and 1518 bytes including

2 user configurable frames Bit Error Rate Testing Patterns: PRBS 2^31 -1, PRBS 2^23 -1, PRBS 2^20 -1, PRBS 2^15 -1,

PRBS 2^11 -1, CRPAT (Layer 1 only), CSPAT (Layer 1 only), CRTPAT (Layer 1 only), Normal and inverted patterns

Error Injection: Bit, CRC, Symbol, IP Checksum One configurable stream with one fixed frame size Throughput Testing Single traffic streams with configurable MAC, VLAN, MPLS, and IP

fields including traffic prioritization via the VLAN tag priority field and the IP header TOS/DSCP field

% of bandwidth allocation is configurable for each streamDifferent traffic profiles (constant, ramp, or bursty) may be configured

for different streamsDifferent frame sizes are user configurable per stream

Smart Loop Layer 1 loopback: loops back all incoming traffic Layer 2 and Layer 3 loopback: loops back all incoming unicast traffic

and drops all incoming multicast and broadcast traffic

Key Measurements Error Measurements: Bit, CRC, symbol, IP checksum, jabber frames,

runt frames, collisions, late collisionsAlarm Detection: LOS, pattern loss, service disruptionFrame/Packet Statistics: Multicast, broadcast, unicast, pause frames,

frame size distribution, bandwidth utilization, frame rate, line rate, data rate, frame loss, frame delay variation

Common Functions & Measurements

Auto Configuration (available on all interfaces)Identification of received signal - instrument configuration based on network type, bit rate, line coding, framing, and test pattern

Frequency MeasurementElectrical Interfaces: Hz & bit/s in ppm ; Resolution: 1Hz

Round Trip Delay (available on all interfaces)Measurement Range: 1μS to 10 seconds Resolution: ±1μs or 1 U.I.

Event LoggingDate and time stamped events in tabular format

Histograms (available on all interfaces)Display of Errors and Alarms versus time Resolution: Seconds, minutes, hours and days

LED Indicators Fixed LEDs for Signal, Framing, Pattern and Errors/Alarms Soft LEDs for PDH & DSn Alarms/Errors displaying historical events

and conditions

OptionsPulse Mask Analysis T-Carrier (DS1/DS3)

• Bit rates: 1.544 Mbit/s (DS1) and 44.736 Mbit/s (DS3)• Mode: Non-Intrusive • Display: Pulse shape with Conformance mask verification • Parameters: Width, Rise/Fall time, Overshoot/Undershoot • Conformance Masks: G.703, ANSI T1.102, T1.403, T1.404

PDH (E1/E3)• Bit rates: 2.048 Mbit/s (E1) and 34.368 Mbit/s (E3) • Conformance Mask: G.703

VF Measurement VF drop/insert via HeadsetABCD bits monitor & transmit in selected timeslot channelProgrammable ABCD states for IDLE, SEIZE, USER (E1, 2.048M) and

ON-Hook, OFF-Hook, WINK, USER for DS1 (1.5M)Tone generation: 1Hz, 1 dB resolution

• Frequency (Hz): 50 to 3950 Hz, res. 1Hz• Level (dBm): +3 to -60 dBmO

ISDN PRI TestingNT and TE emulation Place/receive voice and data callsD-channel monitor with full decode: Layer 2 (Q.921) & Layer 3 (Q.931)Protocols

• DS1 Protocol (1.5M): National ISDN, AT&T, Nortel DMS• E1 Protocol (2M): ETSI (Euro - ISDN)

Via Headset for B-channel talk/listenSupports multirate N x 64k data callSupplementary Services Test: Automatically tests the provisioning of

the following: CLIP, CLIR, COLP, CFU, CFB, CFNR, SUB, MSN, DDI, HOLD, UUS, TP, AOC-S, AOCD, AOCE, MCID, CUG

Jitter Measurement Measurement Range: Per ITU-T 0.171 PASS/FAIL Threshold: Per ITU-T G.823 or User defined Measurement Storage

SPECIFICATIONS

SPECIFICATIONS

Ping Test over WANInterfaces: E1, T1, Datacom (V.24/RS232, V.35/V.11, V.36/RS449

and X.21)Encapsulation types: PPP over HDLC, Ethernet over HDLCIP modes: Static or DHCPPing: Destination IP address, # of Pings, duration, TTL

IP Testing Ping, Trace Route, ARP, FTP/Web tests, Web-browser. These tests are done via the chassis 10/100/1000Base-T and 1000Base-X ports.

VoIP TestingVoIP Check

• Simulates VoIP call to the nearest router• Round Trip MOS score

VoIP Expert• MOS and R-factor measurement• Packet Statistics: packet loss, jitter, delay

VoIP Call Expert• VoIP call setup with VoIP USB adaptor• Supports SIP and H.323 protocols• Codec: G.711U, G.711A, Optional G.723, G.729

IPTVProvides true STB emulationAnalyze up to three streams simultaneouslySupports IGMP/RTSP signaling, MPEG-2, H.264 and VC1 video

compression, MPEG-2 and RTP transport streamsVideo and Audio bit rates and statisticsChannel zapping for quick and complete installation check

NetWizAvailable on 10/100/1000-T test port and 10/100-T management portDetect distance to open/short, wire cross, impedance mismatchNetwork device discovery; Auto Ping verification

Options cont’d

General Specifications

Size 210 x 100 x 55 mm (H x W x D) 8.25 x 3.75 x 2.25 inWeight Less than 1 kg (less than 2.2 lb)Battery LiIon smart battery, 2400 mAh

10.8VDCAC Adaptor Input: 100-240 VAC, 50-60 Hz Output: 15VDC, 3.5AOperating Temperature -10˚C to 50˚C (14˚F to 122˚F)Storage Temperature -20˚C to 70˚C (-4˚F to 158˚F)Humidity 5% to 95% non-condensingDisplay 3.5” QVGA 320x240 full color

touch-screenRuggedness Survives 1.5 m (5 ft) drop to

concrete on all sidesWater-resistance May be used in heavy rainInterfaces USB 2.0, RJ45, 10/100-T Ethernet, Bluetooth 2.0 (optional)Languages Multiple languages supported

VeEX Inc.2255 Martin Ave., Suite G Santa Clara, CA 95050 USATel: +1.408.970.9090Fax: +1.408.970.9099www.veexinc.comcustomercare@veexinc.com

© 2010 VeEX Inc. All rights reserved. VeEX is a registered trademark of VeEX Inc. The information contained in this document is accurate. However, we reserve the right to change any contents at any time without notice. We accept no responsibility for any errors or omissions. In case of discrepancy, the web version takes precedence over any printed literature. D05-00-040P B01 2010/12

The Ver i f icat ion Experts

Ordering Information

Z04-00-010P VePAL TX130+ Handheld DS1 Test Set

Hardware OptionsZ66-00-041P 10/100-T Ethernet BERT, Throughput, RFC2544

H/W optionZ66-00-054P Ethernet HW Load only. Not enabled in

software.

Interfaces/Test Options499-05-009 Ping Test over WAN (E1/DS1) Interface499-05-142 2Mbit/s Pulse Mask Analysis499-05-144 1.5Mbit/s Pulse Mask Analysis499-05-145 DS3 (45Mbit/s) Testing (Dual RX)499-05-146 DS3 (45Mbit/s) Pulse Mask Analysis499-05-147 E3 (34Mbit/s) Testing (Dual RX)499-05-148 E3 (34Mbit/s) Pulse Mask Analysis499-05-149 DS1/E1 Jitter Measurement499-05-152 DS3/E3 Jitter Measurement499-05-155 Dual Port E1 (2Mbit/s)499-05-176 E1 APS/Service Disruption MeasurementZ88-00-008G ISDN PRI (ANSI, ETSI) Call Setup, incl. EarpieceZ88-00-009G VF Measurements, incl. Earpiece

Ethernet Software Options499-05-014 MX MPLS Tags499-05-015 MX Jitter Measurements499-05-058 MX MAC Flooding499-05-059 MX Asymmetric Testing499-05-093 MX VLAN Flooding499-05-154 1000-T Ethernet BERT, Throughput, RFC2544

(requires Z66-00-041P)499-05-178 10/100T Ethernet Software Option (for field

upgrade when Z66-00-054P has been purchased)

Additional Options (via USB, 10/100 Base-T Management Port)499-05-001 Web Browser (requires Advanced IP option)499-05-002 NetWiz499-05-003 Remote Control499-05-008 IPTV Expert (requires Ethernet hardware)499-05-095 VoIP G.723 Codec499-05-096 VoIP G.729 Codec499-05-102 VoIP Check499-05-175 USB Bluetooth Dialing and File Transfer Support

(USB adaptor not included)Z33-00-001 VoIP Expert, incl. VoIP Check optionZ88-00-001G WiFi Wiz, incl. USB WiFi AdaptorZ88-00-001P VoIP Call Expert, incl. VoIP USB Adaptor &

EarpieceZ88-00-005G Advanced IP, incl. Ethernet Cable

Media Converter OptionsZ99-00-024P MC1000, 1000-T to 1000-X Media Converter

with USB Power Cord (requires SFP options)Z99-00-025P MC100, 100-T to 100-FX Media Converter with

USB Power Cord (requires SFP options)301-01-001G 850nm SX (550m) SFP - 1GE, 1G/2G FC301-01-002G 1310nm LX (10km) SFP - 1GE, 1G/2G FC301-01-013G 1310nm 100FX MM (2km) SFP - 100Mbps301-01-014G 1310nm 100FX SM (15km) SFP - 100MbpsA03-00-006G AC Adaptor, US PlugF02-00-026G USB Power Cord

Recommended AccessoriesA02-00-001G Car AdaptorC02-00-002G Carrying Pouch for V100 w/Standard Battery PackD09-00-006 TX130+ Test ReportF02-00-009G RJ48 to 3-Pin Banana Test Cable, 2 mF02-00-010G BNC to BNC Test Cable, 2 mF02-00-011G Bantam to Bantam Test Cable, 2 mF02-00-022G RJ48 to Bantam Test Cable, 2 mF02-00-023G RJ48 to RJ48 Test Cable, 2 mZ77-00-006G LCD Protective Film (Pack of 5)Z77-00-013G* Advanced DS3/DS1 Cable KitZ77-00-016G* Male BNC to WECO Mini 440A Adaptor (Pack of 2)Z77-00-017G* Basic DS3/DS1 Cable KitZ77-00-018G* Male BNC to WECO Adaptor (Pack of 2)Z99-99-007G USB Bluetooth Adaptor (requires 499-05-175)

Replacement Items403-15-001G Top Connector Cover Hinge (Pack of 5)405-02-001G Screen Protector405-02-002G Top Connector CoverA01-00-001G AC Adaptor for V100B02-03-002G Battery Pack for V100B02-06-002G Extended Battery Pack for V100C01-00-001G Carrying Case for V100C03-00-001G Shoulder StrapF02-00-001G Ethernet Cable RJ45 to RJ45 2 m (6 ft)F04-00-001G Power Cord - US 2 m (6 ft)F04-00-002G Power Cord - EU 2 m (6 ft)F04-00-003G Power Cord - UK 2 m (6 ft)Z77-00-001G Stylus with String (Pack of 5)Z99-99-004G Headset/Earpiece (Mini USB Type)

*Check with factory for availability.

ORDERING INFO.