BW1 2.35 THEATRE Concept

www.cineversum.com

Part. No.: R599765

THEATRE Concept

ASSEMBLY AND CALIBRATION

Ref: T9004000 Rev: 02

2 R599765 - 2.35 THEATRE Concept

ChangesCineVERSUM provides this manual ’as is’ without warranty of any kind, either expressed or implied, including butnot limited to the implied warranties or merchantability and fitness for a particular purpose. CineVERSUM maymake improvements and/or changes to the product(s) and/or the program(s) described in this publication at anytime without notice.This publication could contain technical inaccuracies or typographical errors. Changes are periodically made to theinformation in this publication; these changes are incorporated in new editions of this publication.

CopyrightAll right reserved. No part of this document may be copied, reproduced or translated. It shall not otherwise berecorded, transmitted or stored in a retrieval system without the prior written consent of CineVERSUM.

GuaranteeCineVERSUM provides a guarantee relating to perfect manufacturing as part of the legally stipulated terms ofguarantee. On receipt, the purchaser must immediately inspect all delivered goods for damage incurred duringtransport, as well as for material and manufacturing faults. CineVERSUM must be informed immediately in writingof any complaints.If the purchaser or third party caries out modifications or repairs on goods delivered by CineVERSUM, or if thegoods are handle incorrectly, in particular if the systems are commissioned operated incorrectly or if, after thetransfer of risks, the goods are subject to influences not agreed upon in the contract, all guarantee claims of thepurchaser will be rendered invalid. Not included in the guarantee coverage are system failures which are attributedto programs or special electronic circuitry provided by the purchaser, e.g. interfaces. Normal wear as well as normalmaintenance are not subject to the guarantee provided by CineVERSUM either.The environmental conditions as well as the servicing and maintenance regulations specified in this manual mustbe complied with by the customer.

TrademarksBrand and product names mentioned in this manual may be trademarks, registered trademarks or copyrights oftheir respective holders. All brands and product names mentioned in this manual serve as comments or examplesand are not to be understood as advertising for the products of their manufactures.

TABLE OF CONTENTS

1.0 2.35 THEATRE Concept .................................................................................................. 41.1 The optional 2.35 THEATRE Concept (Ref.T9004000) ................................................................... 41.2 Installing the 2.35 THEATRE Slider ................................................................................................. 41.3 Anamorphic Lens alignment.............................................................................................................. 5

First install........................................................................................................................... 5Adjust the 16:9 picture ........................................................................................................ 5Set the horizontal position of the lens ................................................................................. 6Set the tilt and vertical position of the lens ......................................................................... 7Adjust the Anamorphic Lens Focus .................................................................................... 8

2.0 Projector-side configuration ............................................................................................ 92.1 Configure the projector THEATRE Mode......................................................................................... 9

Plug the RF-Emitter to the Trigger 2 output of the projector.............................................. 9 Configure Initial Setup Menu -> Trigger 2 to THEATRE .............................................. 9Select a wide format input: Aspect Ratio to Cinemascope .............................................. 9Select a different input: Aspect Ratio to Full Screen ....................................................... 9

2.2 Using the Remote Control Unit. ...................................................................................................... 10[ASPECT] button behavior ............................................................................................... 10Quick Aspect Ratio changes on the same input ................................................................ 11

2.3 Using RS-232 protocole................................................................................................................... 11Communication Specifications ......................................................................................... 11Command Format.............................................................................................................. 11Available Lengths and Commands.................................................................................... 12

3.0 Miscellaneous .................................................................................................................. 143.1 Dimensions ...................................................................................................................................... 143.2 Projection distances ......................................................................................................................... 14

R599765 - 2.35 THEATRE Concept 3

1.0 2.35 THEATRE CONCEPT


1.1 The optional 2.35 THEATRE Concept (Ref.T9004000)

The Blackwing One centralizes the controls and automation commands of the 2.35 THEATRE Concept for a unique,versatile and unexpectedly simple to operate 2.35:1 theatre experience using the THEATRE Anamorphic Lens.The Blackwing One features the exclusive new version of the award-winning THEATRE Mode for a complete andincomparable control over a motorized anamorphic lens.The new THEATRE Mode features:

• Integrated CIW system.

• Dedicated menu to program the 12V Trigger2 output.

• Direct access button on the Remote Control Unit to switch between Anamorphic and standard formats.

1.2 Installing the 2.35 THEATRE Slider

a)Fix the Anamorphic lens to the 2.35 THEATRE Slider,double check the horizontal level of the Lens to avoid anypicture trapezoidal distortion.

b) Use the 3x M6x15 screws to fix the 2.35 THEATRESlider at the bottom of the projector.

M6x15 screews



1.3 Anamorphic Lens alignment

In order to install the 2.35 THEATRE Concept, you can operate the Anamorphic Lens position and setting up thelens alignment by using the RF-RCU to manually control its position.Plug the 2.35 THEATRE Concept to the main power.

First installThe 2.35 THEATRE Concept comes with a Radio-Frequency remote control unit (RF-RCU) to operate the positionof the Anamorphic Lens.

• Push Button 1 to move the Anamorphic Lens out

• Push Button 2 to move the Anamorphic Lens in front of the projector beam.

Use the RF-RCU supplied with the 2.35 THEATRE Concept during calibration only.

Adjust the 16:9 pictureTo obtain a good 2.35 picture, the 16:9 picture should be properly adjusted in the center of the screen fulfilling theavailable screen height. These adjustment are made by using the Zoom, the vertical shift and horizontal shiftfeatures of the projector. When the picture position is correct, adjust the picture focus.

Adjust the Zoom until the 16:9 picture fulfills the screen height.

Button 1

Button 2

ZOOM

ZOOM



Adjust the picture Focus

Set the horizontal position of the lens

Press button 2 of the RF-RCU to move the Anamorphic Lens in front of the projector beam to obtain a 2.35projection.

FOCUS



Adjust the Anamorphic Lens horizontal position to obtain a centered 2.35 picture. Tighten the 2 screws (A) whencompleted.

Set the tilt and vertical position of the lens

Adjust the Anamorphic Lens tilt and vertical position, so that the projector light beam is centered into the

AA

B

B



Anamorphic Lens. Tighten the 2 screws (B) when completed.

Adjust the Anamorphic Lens Focus

The Anamoprhic Lens features a 6-turns focus ring

The focus adjustment is requiered only on the horizontal x-axis. Turn the focus ring clockwise or anti-clockwisedepending on the distance between the projector and the screen to obtain a clear picture.

You may obtain a residual pincushion effect at the screen when using a throw ratio between 1.5:1 and 1.8:1or a projection distance shorter than 5 meters. It is recommanded to install your projector at a minimumdistance of 5 meters from the screen and using 1.8:1 or higher throw ratio.

If the picture is not focused on the vertical y-axis, that means that the 16:9 picture, without the AnamorphicLens, is not focused. Press button 1 on the 2.35 THEATRE Concept RCU to remove the lens and make theadjustments decribed in “Adjust the 16:9 picture”, page 5.

x

y

Not focused Focused


2.0 PROJECTOR-SIDE CONFIGURATION


2.1 Configure the projector THEATRE Mode

Plug the RF-Emitter to the Trigger 2 output of the projector

Connect the RF-Emitter provided with the 2.35 THEATRE Slider to the 12V Trigger 2 output

Configure Initial Setup Menu ⇒⇒⇒⇒ Trigger 2 to “THEATRE”The “Initial Setup ⇒⇒⇒⇒ Trigger 2” menu determines the Trigger 2 output located in the panel input of the Blackwing Onethis is a global parameter (for all inputs):

• ON: the 12V Trigger 2 is always active when the projector is switched ON.

• OFF: the 12V Trigger 2 is always switched Off.

• THEATRE: this option gives to the projector the full control of the Trigger 2 output levels to control theAnamorphic Lens position depending on the selected input and its aspect ratio.

Select a wide format input: Aspect Ratio to “Cinemascope”When selecting a wide format input (2.35:1, 2.37:1 or 2.40:1), the original aspect ratio of the source is larger than16:9, you can see black bars on the top and the bottom of the screen.

• Select the Cinemascope aspect ratio for this input in the menu “Input Signal ⇒⇒⇒⇒ Aspect Ratio ⇒⇒⇒⇒ Cinemascope”.

• Then choose the correct Cinemascope Aspect Ratio in the menu ”Input Signal ⇒⇒⇒⇒ Cinemascope Aspect Ratio ⇒⇒⇒⇒2.37” so that the black bars disappear and the active picture fulfills the height of the screen.

The Anamorphic Lens is automatically placed in front of the projector to restore the correct picture aspect ratio.

Select a different input: Aspect Ratio to “Full Screen” When you switch to a different input, the Anamorphic Lens is automatically removed from the projector if the aspectratio is not configured in Cinemascope. You can switch back to the previous input, the Anamorphic Lens will beautomatically moved in front of the projector.

RF-EMITTER

12V Trigger 112V Trigger 2



2.2 Using the Remote Control Unit.

Blackwing One RCU and quick access to THEATRE Mode features

[ASPECT] button behaviorThe [ASPECT] button triggers the 5 aspect ratio modes. Once a given aspect ratios is selected, the order of the nextaspect ratio is reversed so that the previous aspect ratio becomes the next aspect ratio as described below.

Select active input

Select the correctAspect Ratio

Standard Cinemascope

Converted 16:9

Full Screen

Virtual Wide

When you press sequentially the [ASPECT] button, the aspect mode rotation goes clock-wise. Press [ESC] or wait 15 seconds until the message fades out to confirm

Next time that you will press the [ASPECT] button, the rotation order is reversed. This

The 2.35 THEATRE Concept uses Full Screenand Cinemascope aspect ratios.

behavior ensures a fast switch between different aspect ratios.

selection.



Quick Aspect Ratio changes on the same inputIf Trigger 2 is set to THEATRE Mode, the 2.35 THEATRE Slider is automatically operated by selecting the“Cinemascope” aspect ratio by pressing sequentially the [ASPECT] button on the RCU. The projector will retain theaspect ratio setting for the selected input. To switch back to 16:9, choose the ”Full Screen“ aspect ratio.

You can also use the Remote Control Unit by pressing twice the [ASPECT] button to switch forth and backward fromCinemascope to Fullscreen modes as described below:

2.3 Using RS-232 protocole

Communication SpecificationsControl of 2.35 THEATRE Concept is possible using a computer or automation device connected with a RS-232straight cable connected to the Blackwing One (male - female D-sub 9 pins cable). Communication specificationsfor this unit are as follows:

Command Format

When sending a command to this unit, use the following data format:

Baud Rate 115200 bps

Data Format Binary

Character Length 8 bits

Parity None

Stop Bit 1 bit

X on/off None

Flow Control None

Header Length Command EoD1 or 3 bytes 0 or 1 byte at least 1 byte 1 byte

Header (00h) for power ON command, (77h 88h 99h) for other commands.

Length The total bytes of “Length” and “Command”

Command Designates the command

EoD Designates the end of the data. Fixed to (FFh)

Full Screen Cinemascope

... press twice [ASPECT] button on the Remote Control Unit

When the source automatically switches format...

16:9 format

2.35:1 format

Full Screenon 2.35 screen



Available Lengths and CommandsCommand Header

(00h)Length Command Description

Power ON None 01h If the projector is in standby mode, this commandswitch the unit ON.

Command Header(77h 88h 99h)

Length Command Description

Power OFF03h 02h 01hh If the projector is powered ON, this command

switch this unit into Standby Mode. (Directly OFF)Switch Input 03h 02h 02h Switch active input to Video (Composite)

02h 03h Switch active input to S-Video02h 04h Switch active input to Component02h 05h Switch active input to VGA (sD15)02h 06h Switch active input to HDMI 102h 07h Switch active input to HDMI 2

Blanking 03h 02h 08h Toggle projector Blanking ON02h 09h Toggle projector Blanking OFF

Keypad 03h 01h 01h MENU: Toggle OSD Menu ON and OFF01h 02h UP: Uses as up function key for navigation01h 03h DOWN: Uses as down function key for navigation01h 04h LEFT: Uses as left function key for navigation01h 05h RIGHT: Uses as right function key for navigation01h 06h ENTER: Selects menu item or the next menu01h 07h EXIT: exits the current menu to the previous one.01h 08h SOURCE: Switch input source.01h 09h Power OFF: Turn off the projector (send twice)

12V Trigger #2 03h 03h 01h Switch the trigger to ON.03h 02h Switch the trigger to OFF03h 03h Switch the trigger to THEATRE

Aspect Ratio 03h 03h 04h Switch aspect ratio to Standard03h 05h Switch aspect ratio to Full Screen03h 06h Switch aspect ratio to Cinemascope03h 07h Switch aspect ratio to Converted 16:903h 08h Switch aspect ratio to Virtual Wide

Lens Aperture 03h 03h 09h Open one level up the Lens Aperture03h 0Ah Close on level down the Lens Aperture

Picture Mode 03h 04h 01h Switch picture mode to Standard04h 02h Switch picture mode to Dynamic04h 03h Switch picture mode to Theater04h 04h Switch picture mode to User 104h 05h Switch picture mode to User 204h 06h Switch picture mode to User 3

Picture Adjust 03h 05h 01h Show brightness slider (use left or right to modify)05h 02h Show contrast slider05h 03h Show colour slider05h 04h Show hue slider05h 05h Show sharpness slider05h 06h Show black level slider05h 07h Show white level slider



Examples

Colour Temperature 03h 06h 01h Switch colour temperature to Low06h 02h Switch colour temperature to medium06h 03h Switch colour temperature to High06h 04h Switch colour temperature to User 106h 05h Switch colour temperature to User 206h 06h Switch colour temperature to User 306h 07h Switch colour temperature to Medium-high

Gamma 03h 07h 01h Switch gamma to Gamma 107h 02h Switch gamma to Gamma 207h 03h Switch gamma to Gamma 307h 04h Switch gamma to Gamma 407h 05h Switch gamma to User 107h 06h Switch gamma to User 207h 07h Switch gamma to User 3

Scaling features 03h 08h 01h Set detail enhancement to Off08h 02h Set detail enhancement to Low08h 03h Set detail enhancement to Medium08h 04h Set detail enhancement to High

Temporal Noise 03h 08h 05h Set TNR to Off08h 06h Set TNR to Low08h 07h Set TNR to Medium08h 08h Set TNR to High

Mosquito Noise 03h 09h 01h Set MNR to Off09h 02h Set MNR to Low09h 03h Set MNR to Medium09h 04h Set MNR to High

Block Artifact 03h 09h 05h Set BAR to Off09h 06h Set BAR to On

Reset to default 03h 0Ah 01h Reset settings to default value

You want to... Command to sendSwitch the projector ON 00h 01h FFhSwitch the projector OFF 77h 88h 99h 03h 02h 01h FFhSwitch the projector OFF with OSDconfirmation

77h 88h 99h 03h 01h 09h FFh

Change Active Input to Comp. 77h 88h 99h 03h 02h 04h FFhSwitch to 16:9 screen 77h 88h 99h 03h 03h 05h FFhSwitch to Cinemascope screen 77h 88h 99h 03h 03h 06h FFhDisplay On Screen Menu 77h 88h 99h 03h 01h 01h FFhChange aspect ratio to Cinemascope 77h 88h 99h 03h 03h 06h FFhChange aspect ratio to Full Screen 77h 88h 99h 03h 03h 05h FFh


3.0 MISCELLANEOUS

3.0 MISCELLANEOUS

3.1 Dimensions

3.2 Projection distances

Projection Screen SizeDiagonal size

(Aspect Ratio 2.35:1)

Projection Screen Base size

Projection ScreenHeight

Blackwing One

Projecting Distanceminimum - maximum

107" (2720 mm) 98.4" (2500 mm) 41.7" (1060 mm) 3310 mm - 4780 mm

128" (3250 mm) 118.1" (3000 mm) 50.4" (1280 mm) 3960 mm - 5720 mm

149" (3780 mm) 137.8" (3500 mm) 58.7" (1490 mm) 4610 mm - 6650 mm

170" (4520 mm) 157.5" (4000 mm) 66.9" (1700 mm) 5260 mm - 7590 mm

200" (5080 mm) 184.3" (4680 mm) 77.5" (1970 mm) 6190 mm - 8930 mm

530 mm

20.9’’

691

mm

27.2

’’

530 mm

20.9’’

199 mm7.8’’

691 mm

27.2’’


Contact Information:

TEC - CineVERSUM7, rue La CAILLE, 75017 Paris - FRANCEWeb: www.cineversum.com

Contact informationTEC - CineVERSUM7, rue La Caille, 75017 Paris, Francewww.cineversum.com
Part. No. R599765

BW1 2.35 THEATRE Concept

Documents

Transcript of BW1 2.35 THEATRE Concept