Bul 140U /140UE/ 140M Rotary Operating Mechanism Kit for J ... · Bulletin 140U /140UE / 140M...
Transcript of Bul 140U /140UE/ 140M Rotary Operating Mechanism Kit for J ... · Bulletin 140U /140UE / 140M...
Installation Instructions
WARNING: To prevent electrical shock, disconnect from power source before installing or servicing. Follow NFPA 70E requirements. Install in suitable enclosure. Keep free from
contaminants.
Installation, adjustments, putting into service, use, assembly, disassembly, and maintenance shall be carried out by suitably trained personnel in accordance with applicable code of
practice. In case of malfunction or damage, no attempts at repair should be made.
Bulletin 140U /140UE / 140M Rotary Operating Mechanism Kit for J-Frame Circuit Breaker(Cat 140U-J-_ _ _)
1 2
3 4
Operating Mechanism Installation
Test full range of motion
2
Remove wire tie
after installation
0.7 - 0.9 Nm
(6 - 8 lb-in)
buttontripPush to
Make sure tab
engages slot
1
1
Customer-supplied
pad lock
Bulletin 140U /140UE / 140M Rotary Operating Mechanism Kit for J-Frame Circuit Breaker2
Publication 140U-IN049A-EN-P - January 2013 PN-188947 DIR 10000484010 (Version 00)
21
1 2
Operating Shaft Modification and Installation
Operating Handle Installation
C
C -159
C - 5-9/16
3(1/8)
6.35(1/4)
Ø 3(Ø 1/8)
mm
(in.)
3
C
MIN MAX
2
3
1
2
2
1
1
0.9 - 1.1 Nm
(8 - 10 lb-in)
196.8
(7 - 3/4)
679.4
(26 - 3/4)
196.8
(7 - 3/4)
533
(21)
305
(12)
450.8
(17 - 3/4)
Bulletin 140U /140UE / 140M Rotary Operating Mechanism Kit for J-Frame Circuit Breaker 3
Publication 140U-IN049A-EN-P - January 2013 PN-188947 DIR 10000484010 (Version 00)
3
4
Operating Handle Installation (Cont’d)
(25 lb - in)
T-20
6 mm
1/4 in
TAPE
ø35 mm
1-3/8 in. d
ia.
Front o
f Cover
Partie fr
ontale du panneau
Vorderseite
des deckels
Frente de la ta
pa
Frente da tampa
Parte fr
ontale del panello
2 - ø5.5 m
m
2 - 7/32 in
. dia.
2 - ø5.5 m
m
2 - 7/32 in
. dia.
Drillin
g template
Gabarit de perfo
ration
Bohrschablone
Plantilla de perfo
ración
Modelo de perforação
Stampo preforato
PN-124909
DIR 10000207927 (V
ersion 00)
or
ou
oder
o
or
ou
oder
o
ø35 mm1-3/8 in. dia.
Front of CoverPartie frontale du panneau
Vorderseite des deckelsFrente de la tapaFrente da tampa
Parte frontale del panello
2 - ø5.5 mm2 - 7/32 in. dia.
2 - ø5.5 mm2 - 7/32 in. dia.
Drilling templateGabarit de perforationBohrschablonePlantilla de perforaciónModelo de perforaçãoStampo preforato
orou
odero
orou
odero
Cover Thickness:1.2 - 4.8
(3/64 - 3/16)
Front of Cover
50
(1-31/32)
50
(1-31/32)
25
(63/64)25
(63/64)
(2) - ø 5.5
((2) - ø 7/32)
ø 35
(ø 1-3/8)
63
(2-15/32)
31.5
(1-15/64)
(2) - ø 5.5
((2) - ø 7/32)
ø 35
(ø 1-3/8)
mm
(in.)
OR
PN-188947DIR 10000484010 (Version 00)
Copyright © 2013 Rockwell Automation, Inc. All Rights Reserved. Printed in USA.
Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.
Trademarks not belonging to Rockwell Automation are property of their respective companies.
Handle On - Open or Close Enclosure Handle On with Defeater Plug
Handle Off - Open or Close Enclosure Lock handle Off with Enclosure Door Interlock
1
2
1
2
1
2
mm
(in.)
1
2
3.5 mm Max.
.140 in. Max.
Publication 140U-IN049A-EN-P - January 2013
A
104.8
(4-1/8)
139.7
(5-1/2)
27
(1-1/16)
61.9
(2-7/16)
34.9
(1-3/8)
34.9
(1-3/8)
34.83
(1-3/8)
34.83
(1-3/8)
7.95
(5/16)
7.95
(5/16)
B C D E
3 Pole
Breaker
4 Pole
177.8
(7)
Mounting Plate
Load Side
Line Side
4 P
ole
Ou
tlin
e
3 P
ole
Ou
tlin
e
139.7
(5-1/2)
139.4
(5 - 1/2)
84.9
(3 - 11/32)
170.6
(6 - 23/32)
679.4
(26 - 3/4)
A
B C
E
D
A
51
(2-1/64)
114
(4-31/64)
Max. (12” Operating Shaft)
450.8
(17 - 3/4)Max. (21” Operating Shaft)
196.8
(7 - 3/4)Min.
Reset
B C
Mounting Plate
For 3 Pole Breaker Mounting:
Drill and tap four M4 x .7 holes into
mounting plate.
For 4 Pole Breaker Mounting:
Drill and tap six M4 x .7 holes into
mounting plate.
CONFIDENTIAL AND PROPRIETARY INFORMATION. THIS DOCUMENT CONTAINS CONFIDENTIAL AND PROPRIETARY INFORMATION OF
ROCKWELL AUTOMATION, INC. AND MAY NOT BE USED, COPIED OR DISCLOSED TO OTHERS, EXCEPT WITH THE AUTHORIZED WRITTEN
PERMISSION OF ROCKWELL AUTOMATION, INC.
Sheet
Size Ver
Of 11
A 001000021659Dr. DateG. USHAKOW 2-10-10
SPECIFICATIONS FOR4 PAGE INSTRUCTION SHEET4-1/4” W x 5-1/2” H - FINAL FOLD
MATERIALSIZE
FOLD
TWO SIDES PRINTEDBODY STOCK WHITE
BODY INK BLACK4-1/4" W x 5-1/2" H
FLAT
17" W x 11" H
5-1/2”
8-1/2"
PAGE 2
PAGE 1
11"
8-1/2"
PAGE 3
PAGE 4
Page Layout
Note: After folding---Printed in (Country where printed)* and instruction sheet number in lower left corner should be visible.
* The printing vendor may change the instruction sheet files to show the correct country.
Final Fold
4-1/4”
PN-12345DIR 100000000 (Version 00)Printed in U.S.A.