Building and ductwork airtightness requirements in...
Transcript of Building and ductwork airtightness requirements in...
Building and ductwork airtightness
requirements in Europe
TightVent Airtightness Association
Committee
January 12th, 2016
Analysis of answers of airtightness associations representatives performed by:
Valérie Leprince, Maria Kapsalaki, Rémi Carrié
Presentation
• The objective of this study is to compare approaches for requirements and competent tester schemes for building and ductwork airtightness in various European countries.
• Special thanks to the persons who have kindly answered the questionnaires:
– Barry Cope (ATTMA), UK – Oliver Solcher (FliB), Germany – Liesje Van Gelder (BCCA), Belgium- Flemish region – Owe Svensson (SP), Sweden – Jiri Novak (FSV, CVUT), Czech Republic – Radoslaw Gorzenski (PUT),Poland – Targo Kalamees (TTU) , Estonia – Mark Shirley (2eva), Ireland – Adeline Mélois (CEREMA), France – Russel Macdonald (iATS), UK – Vladislavs Kevišs (Irbest), Latvia – Jurgen Luft (Woehler), Germany
BUILDING AIRTIGHTNESS
EP-regulation
Airtightness reference
• 8 out of 10 countries have at least one indicator that use the envelope area as reference value – Germany use internal volume for buildings below 1500m3/h and envelope area for
others – France use envelope area but without low floor
• 9 out of 10 countries have a reference pressure value at 50 Pa
50 Pa
4 Pa
Reference value Pressure
Regulatory EP-calculation depends
on building airtightness ?
• When building airtightness is not taken into account in EP-calculation it may be hard to promote it – Building airtightness is
not taken into account in 3 out of 10 countries
– However minimum requirement exist in Czech Republic
Yes
No
Minimum building airtightness requirements
in some cases in EP regulation?
Does this maximum value have to be justified?
Yes, by systematic testing Yes, by systematic testing or by applying a certified approach No Not necessarily
Yes
No
Minimum building airtightness
requirements • Minimum requirements exist in 6 out of 10 countries
but do not necessarily need to be systematically justified
– Only Ireland, UK and France impose systematic justification
• In Belgium there is no minimum requirement but the default value for airtightness is such penalizing therefore 30-50% of new buildings are tested
• In Germany the test is done in most of new buildings
• Two countries propose an alternative to systematic testing: a certified quality approach for building (IE and FR)
Minimum requirement value < 10 m³/h.m² @ 50 Pa
< 1500 m3 : n50 < 3 1/h < 1.5 1/h
> 1500 m3 : q50 < 4.5 m3/h/m² < 2.5 m3/h/m²
n50 4.5 1/h 1.5 1/h 1 1/h 0.6 1/h
Recommendations: n50 3 1/h 1.5 1/h The measured building airtightness should not be higher than the value used in EP-calculation
q50 ≤ 7 m3/h/m²
q4Pa_surf 0.6 m3/h/m² 1 m3/h/m²
Recommendations: q50 3 m3/h/m² 2 m3/h/m² 1.5 m3/h/m²
Equivalent area assuming V/A= 1.1 m
Keys
Single-family house/multi-family building/ non-
residential building
Blue: Retrofitted; Green: New
Without mechanical ventilation /With
mechanical ventilation / With heat recovery
Passive house
Relative area. Proportional to the q50 or
calculated q50 if the requirement is not
expressed in q50 (assuming V/S=1.1m).
Countries for which EP-regulation require a
minimum airtightness level that has to be
justified
Summary of EP-regulation Country EP regulation(s)
Minimum requirement applies to:
Approved Document L of the Building Regulations in England and Wales. Technical Handbook 6 in Scotland.
Energieeinsparverordnung EnEV 2014
EPB x ČSN 73 0540-2 Thermal performance of buildings - Part 2 - Requirements
Regulation of the Minister of Infrastructure on the technical conditions that should be met by buildings and their location x Methodology for calculating the energy performance of buildings, regulation of Minister of Economic Affairs and Communications. Minimum requirements for energy performance, regulation of Government
x
EPBD -->Ireland 2011 Part (L) --> verified via DEAP software programme from government body SEAI
RT2012
BUILDING AIRTIGHTNESS
Programmes
Programme EP-calculation depend
on building airtightness ?
• In Czech republic,
airtightness in not
taken into account in
regulatory EP-
calculation but is in
programme
calculation Yes
No
Minimum building airtightness requirements
in some cases in EP programmes?
• Does this maximum
value have to be justified?
Yes, by systematic testing Yes, by systematic testing or by applying a certified approach Yes by testing some buildings selected by a third party
• 7 out of 10 countries have programmes with requirement on airtightness
Yes
No
Minimum requirement value q50< 10 m³/h.m²
< 1500 m3 n50 < 3 1/h < 1.5 2/h
> 1500 m3 q50 < 4.5 m3/h/m² < 2.5 m3/h/m²
n50 2.5 1/h 0.6 1/h
NF40 NF 15
n50 1 1/h 0.6 1/h
0.6 1/h
q50 ≤ 7 m3/h/m²
q4Pa_surf 0.4 m3/h/m² 0.8 m3/h/m²
Equivalent area assuming V/A= 1.1 m
Summary of Programmes Country Programme
Minimum requirement applies to:
SAP - Standard Assessment Procedure
DIN V 4108-6/ DIN V 4701-10; DIN V 18599
Passiefhuis
New Green Savings Programme (state subsidies programme for construction of energy efficient buildings)
NF15 and NF40 by National Fund for Environmental Protection and Water Management
Irish Building Regulations Technical Guidance Document Part (L) - Conservation of Fuel & Energy
Effinergie +, BEPOS Effinergie
BUILDING AIRTIGHTNESS
Airtightness tester schemes
Is there a quality framework for
testers in your country? • 7 countries out of 10 now
have a quality framework for building airtightness testers
• In 4 countries out of the 7 this qualification is required for testing in the context of the EP-regulation or/and a EP-programme
– In UK the qualification is not required but if test is performed by a qualified tester a «standardised certificate » is automatically issued (no need for the tester to make a full report)
Is the qualification mandatory for
testing in the context of:
The regulation
A programme Both
regulation
and
programme Not required
Yes
No
40 542
1000
20020
250
20
Qualified tester are increasing
in Europe January 2013 January 2014 June 2015 January 2017
>1100 testers >1350 testers >1800 testers
>2000 testers
• The number of tester is increasing rapidly in Belgium, Ireland, France and UK
– Either because they are requiring airtightness testing in regulation (FR, UK, IE)
– Or because they are promoting airtightness by awarding the EP- calculation if test is performed (BE)
• In Germany this is only Flib figures but other qualifications exist
Have guidelines for airtightness testing (apart from ISO
9972) been published or updated in your country in the last
5 year?
• Only 4 countries out of 10 have issued guidelines
• Quality framework does not require guidelines
– Czech republic, Ireland and Sweden have a quality framework but no specific guidelines
– No country have guidelines without quality framework
Yes
No
Qualification tester schemes
and guidelines Country Qualification tester schemes Guidelines Previous Guidelines
Air Tightness Testing & Measurement Associations (ATTMA) The Independent Airtightness Testing Scheme (iATS)
ATTMA TSL1 2016 (Dwellings), ATTMA TSL2 (Non-Dwellings) 2010 (currently under revision)
There are some certification schemes. I.e. FLiB- certification.
EnEV 2014
EnEV 2009
Kwaliteitskader Luchtdichtheid
STS-P 71-3 2014
yes, specification document with additional requirements of government 2013
Diplomerad lufttäthetsprovare (diplomaed airtightnestester)
Not published yet, but we are working on ByggaL (means "Building airtight") and part of that is a guideline for airtightness testing in Sweden. Hopefully it will be published in this year
Membership in the Association Blower Door CZ
The National Standards Authority of Ireland- NSAI (95% of testers), The Irish National Accreditation Board - INAB and we also recognise the British ATTMA
Qualibat 8711 FD 50-784, 2016 GAP 50-764, 2014
BUILDING AIRTIGHTNESS
Database
Is there available field data on building airtightness
levels achieved in your country?
Yes it represents almost all measured data (90-100%) Yes it represents a large amount of measured data (60-90%) Yes it represents about half measured data (40-60%) Yes it represents a moderate amount of measured data (10-40%) Yes it represents a small amount of measured data (0-10%) No data available
What is the specificity of the buildings
and/or testers that performed the tests?
• 6 countries out of 10 have a database
– In Germany this is rough figures from Flib members
• Mainly new residential buildings tested by qualified testers
Database sources and access Country Database source How to have access to this data or studies:
Both iATS and ATTMA maintain a lodgement scheme for completion results.
For ATTMA: A case must be made to explain why you want the data, who you are and what you intend to do with it. We would also ask that any publications are run past us first. For iATS: Access would have to be arranged with co-operation from iATS directors. Please contact [email protected]
Flib asks its members for rough figures (not mandatory)
http://www.flib.de/presse/2015/05/2015_05_Meld_Statistik15_I.pdf
BCCA database, EPBD database
databases are not public
Database of test results collected by the members of Association Blower Door CZ
contact person: Jiri Novak, [email protected]
Overview of measurements, 2008.
https://www.etis.ee/File/DownloadPublic/3cf0f211-274f-4bcf-a63a-6f01651e48b9?name=Fail_Raport.pdf&type=application/pdf http://dx.doi.org/10.1016/j.buildenv.2006.06.001
Only via individual testers If needed a lead person could be appointed to role out a questionnaire or the format that you wish to use and a methodology be put in place to gather the information.
Data collection via Qualibat qualification (required)
Various articles have been published they are available on airbase (AIVC database): key authors are Mélois, Bailly, Guyot, Carrié, and Leprince.
Irbest as largest tester company could provide some statistic data for last period
BUILDING AIRTIGHNESS
Awarness
What has changed regarding building airtightness
in the last 5 years in your country?
• In every country things have changed!
• Significant increase of awareness for 3 out of the
10 countries, moderate increase for the 7 others
– In Sweden the awareness has increased mostly before 2011
• New regulation in 6 countries out of 10
– 4 countries (IE, CZ, SE, LV) have had neither new regulation nor new programme in the last 5 years
– For Ireland airtightness requirements were introduced before 2011
Test of large buildings
Reduced maximum value
What were the motivations for change?
• Energy use and national policy
are the main drivers for change
• Indoor air quality comes last:
only Ireland quote it
What is in your view the progress needed to
promote building airtightness in your country?
• Energy use is the main driver and remains the main progress needed for 7 out of the 11 respondents
• Long-term performance come 2nd, there is on going project in various countries
• Impact on IAQ comes 4th
- Better understanding of building air tight to avoid damages in the construction
- Cost savings during building operation
DUCTWORK AIRTIGHTNESS
Ductwork airtightness
• Only Belgium, France, Latvia and Germany have
completed the questionnaire
• Czech republic and Poland have answered that
ductwork airtightness was not really considered
in their countries
• Answers from Sweden, UK, Ireland, Spain and
Estonia are missing
How ductwork airtightness is taken into
account in regulations?
• Only France (RT2012) and Belgium (EPB) consider ductwork airtightness as an input in EP-regulation
– But there is no minimum requirement
– In France if a value better than default value is used then it has to be justified (testing or certified quality approach)
• In Belgium the leakage flow according EN 14134 is used
– The ductwork area is not estimated
• In France the airtightness class is used according EN 12237
– The ductwork area is estimated either with flat rate based on building floor area (residential buildings) or with flat rate based on flowrate (non-residential buildings)
How ductwork airtightness is taken into
account in EP-programmes?
• Only French programme Effinergie + and
Effinergie BEPOS get requirement on ductwork
airtightness with required justification
– It applies to new buildings
– Class A is required
Qualification for ductwork testers
• Among respondent, only France has a
qualification for ductwork testers (Qualibat 8721)
– The qualification is required for testing in the context of regulation and programme.
– 35 testers are qualified
• Specific guidelines exist: FD E 51-767, 2014
• No field data are available yet but their should
be in 2017 in France
Awareness for ductwork airtightness
• Among respondent, only France has had change regarding ductwork airtightness in the last 5 years with a new regulation, a new programme, a new qualification an increasing number of test and an increasing of awareness.
• The awareness on ductwork airtightness has increased moderately in France, Belgium and Germany
– In Belgium likely because of broader awareness of efficiency of ventilation system
What is in your view the progress needed to
promote ductwork airtightness in your country?
• As for building airtightness
the main driver for change will
probably be energy use
therefore progress are
needed in this topic
Conclusion: Lots of change in 5 years
regarding building airtightness
In most countries building airtightness is taken into account in EP- calculation
• Requirements with mandatory justification in 3 countries (many test s in 2 others)
• Lot of programmes
• Required values may be easy to achieve
Airtightness testers schemes
• 7 out of 10 countries have an airtightness testers schemes
• The number of testers in Europe has almost doubled in 4 years
• Database are set in 6 out o f 10 countries
Every countries agree that things have changed in the last 5 years
• The main driver is energy : more work are needed on this topic
• The IAQ problem came farther but the problem of airtightness in not ventilated building (ex. refurbished) has been raised
Conclusion: ductwork airtightness
low awareness • Only France and Belgium seem to take into
account ductwork airtightness in their
regulations
• Only France have a EP- programme with
requirements on ductwork airtightness and a
qualification for testers
• Progress are needed to better understand the
impact of ductwork airtightness on energy use
(fan, cooling and heating)
THANK YOU FOR
YOUR ATTENTION
Analysis of answers of airtightness associations representatives performed by: Valérie Leprince, Maria Kapsalaki, Rémi Carrié