Buffet - images-na.ssl-images-amazon.com › images › I › A1rbAwqHQc… · Home Styles Customer...
Transcript of Buffet - images-na.ssl-images-amazon.com › images › I › A1rbAwqHQc… · Home Styles Customer...
Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
88 5100 006
BuffetIMPORTANT
Refer to later page(s) of theseinstructions for drawer assembly.
Carefully remove all the parts from the carton andplace them individually on a soft cloth to preventscratches or other damage.
Carefully and strictly follow these assembly instructionsto ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
A.Side Panel1 pc.
B.Side Panel1 pc.
E.Back Panel3 pcs.
C.Middle Panel1 pc.
D.Middle Panel1 pc.
F.Back Upright2 pcs.
G.Back Stretcher1 pc.
H.Back Stretcher1 pc.
I.Front Stretcher1 pc.
J.Front Stretcher1 pc.
K.Front Upright2 pcs.
Q.Shelf2 pcs.
L.Fixed Shelf1 pc.
M.Base1 pc.
O.Wine Grid2 pcs.
P.Wine Grid2 pcs.
Hex Wrench1 pc.
Small Hex Wrench1 pc.
M6x35Head Cap Bolt4 pcs. (+1 extra)
M6x50Head Cap Bolt (long)8 pcs. (+1 extra)
Cam Lock14 pcs. (+2 extra)
Cross Dowel8 pcs. (+1 extra)
Cam Lock Screw14 pcs. (+1 extra)
M3.5x25Wood Screw (long)24 pcs. (+1 extra)
M3.5x13Wood Screw (short)12 pcs. (+1 extra)
Adjustable Pin8 pcs. (+2 extra)
M3.5x16Wood Screwfor Back Panel12 pcs. (+1 extra)
Pull Handle3 pcs.
M4x25Machine Screw8 pcs.
Knob2 pcs.
R.Door1 pc.
S.Door1 pc.
N.Leg2 pcs.
T.Drawer3 pcs.
Assembly Instructions 2/8
IMPORTANT� Use a soft cloth between these parts and the floor.� Do not use power tools above 8 volts to assemble.� Do not tighten all the bolts until each part is properly assembled.� The unit must be level to work properly. Use the included adjustable levelers to level.� Keep Hex Wrench in a safe place as the bolts may need to be tightened up in the future.
Figure 1
Cam Lock Screw
L
C
D
Cam Lock
STEP 2
Attach Middle Panels (C) and (D)to Fixed Shelf (L) with Cam Locks.
(See Figure 2)
Figure 2
C
D
A
B
STEP 1
Insert Cam Lock Screws into pre-drilled holesof Side Panels (A), (B) and Middle Panels (C), (D).(See Figure 1)
Assembly Instructions 3/8
GH
E
F
Cross Dowel
Head Cap Bolt (long)
STEP 4
Attach Back Stretcher (G) tounit with Cross Dowelsand Head Cap Bolts (long).
Figure 3
IK
KJ
E
E
F
STEP 3
Attach Back Stretcher (H) to unit with Cross Dowelsand Head Cap Bolts (long). (See Figure 3)
Attach Back Uprights (F) to Back Stretcher (H).
Slide Back Panels (E) into place.
STEP 5
Attach Front Stretcher (J) to unit.
Attach Front Uprights (K) to unit.
Attach Front Stretcher (I) to unit.
Cross Dowel
Head Cap Bolt (long)
Assembly Instructions 4/8
A
B
Cam Lock
STEP 6
Attach Side Panels (A) and (B) tounit with Cam Locks.
STEP 7
Attach Base (M) to unit with Cross Dowelsand Head Cap Bolts (long).
Attach Legs (N) to Base (M) with Head Cap Bolts.
STEP 8
Insert Cam Lock Screws into pre-drilled holes of Top.
Cam Lock Screw
Head Cap Bolt (long)
Head Cap Bolt
N
M
N
‘Arrow’ sticker at front
Cam Lock
Cross Dowel
Assembly Instructions 5/8
STEP 9
Turn unit to its’ upright position.
Insert Adjustable Pins intoside panels and middle panelsat desired level.
Place Shelves (Q) into position.
Attach Doors (R) and (S) to unit bysliding door lift hinges intoside panel lift hinges.(See Figure 4)
Attach Knobs to Doors (R) and (S)with Machine Screws. (See Figure 5)
Figure 4 Figure 5
Q
Q
R
S
Cam Lock
Adjustable Pin
STEP 10
Attach Top to unit with Cam Locks.
Note: ‘Arrow’ sticker indicates front of Top.
Assembly Instructions 6/8
STEP 13
Attach Pull Handle with Machine Screws.
STEP 12
Slide Drawer Bottom (T5) into the groovesof Drawer Sides (T3) and (T4) until it meetsDrawer Front (T1).
Attach Drawer Bottom (T5) to unit withWood Screws (short).
T1
T2
T3
T4
T5
T1.Drawer Front3 pcs.
T2.Drawer Back3 pcs.
T3.Drawer Side3 pcs.
T4.Drawer Side3 pcs.
T5.Drawer Bottom3 pcs.
Drawer (T)
STEP 11
Attach Drawer Front (T1) and DrawerBack (T2) to Drawer Side (T3) withWood Screws (long).
Attach Drawer Side (T4) to unit withWood Screws (long).
Pull Handle
T1
T2
T3
T4
Bottom
Roller at back
Wood Screw (long)
Wood Screw (short)
Machine Screw
Part List
Assembly Instructions 7/8
T
P
O
O
STEP 14
Slide Drawers (T) into position.
Slide Wine Grids (P) into thegrooves of Fixed Shelf (L).
Slide Wine Grids (O) into unit.
STEP 15
Level unit by adjusting the adjustablelevelers on bottom of unit.(See Figure 6)
Insert Wood Screws for Back Panelinto pre-drilled holes of back panel.
Note: Unit must be level beforetightening these screws.
Wood Screw for Back Panel
P
T
T
Figure 6
L
Assembly Instructions 8/8
Hardware List
STEP 16
Place unit at desired location.
Drill a 3/8” hole in wall in-line withPre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall holeand attach Bracket with Wall Screw.
Attach Bracket at pre-drilled holeat top of unit with Wood Screw.
Move unit back into place.
Slide Tip-over Restraint throughBracket on wall and Bracket on unit.(See Figure 7)
Put tie end of Tip-over Restraint into lockend of Tip-over Restraint and pull until tight.
Anchor1 pc. (+1 extra)
Bracket2 pcs. (+1 extra)
Tip-over Restraint1 pc. (+1 extra)
M3.5x40Wall Screw1 pc. (+1 extra)
M3.5x16Wood Screw1 pc. (+1 extra)
Figure 7
Wood Screw
Wall ScrewBracketon wall
Anchor in wall
3/8” wall hole
Pre-drilled holeat top of unit
Tie end
Lock end
Bracket attop of unit
Tip-overRestraint
IMPORTANT� To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly.
Drill 3/8” hole in wall
Top of unit
NEVERuse glass cleaners on
finished furniture. Ammoniachemically attacks the finish.
allow liquids to remain on furniture.Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubberbased placemats.
PREVENTDISCOLORING
Do not use commercialwaxes and polishes.
PREVENTYELLOWING
Do not place hotobjects on surface.
PREVENTFINISH DAMAGE
Do not writedirectly on surface.
PREVENTMARKING
Do not use power toolsabove 8 volts to assemble.
PREVENTCRACKING
Do not placein direct sunlight.
PREVENTFADING
with a soft cloth moistenedin lukewarm soap and water.Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days ofpurchase. Digital images of the defective parts may be required. If the product was not purchased from an authorizedretail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembleditems nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,[email protected], 888-680-7460, 877-831-0319
Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Drill (8 volts or less), 3/8” Drill Bit
88 5100 302
HutchIMPORTANT
Carefully remove all the parts from the carton andplace them individually on a soft cloth to preventscratches or other damage.
Carefully and strictly follow these assembly instructionsto ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
A.Top1 pc.
Cam Lock18 pcs. (+2 extra)
Cam Lock Screw18 pcs. (+1 extra)
M4x13Wood Screwfor Steel Plate Connector8 pcs. (+1 extra)
M3.5x16Wood Screwfor Back Panel12 pcs. (+1 extra)
Adjustable Pin12 pcs. (+1 extra)
M4x25Machine Screw2 pcs.
Knob2 pcs.
Steel Plate Connector2 pcs.
Hutch Unit
F.Back Stretcher1 pc.
G.Back Stretcher1 pc.
I.Fixed Shelf1 pc.
H.Front Stretcher1 pc.
J.Shelf1 pc.
K.Shelf2 pcs.
D.Back Panel3 pcs.
E.Back Upright2 pcs.
N.Door1 pc.
O.Door1 pc.
L.Middle Panel1 pc.
M.Middle Panel1 pc.
B.Side Panel1 pc.
C.Side Panel1 pc.
Assembly Instructions 2/6
IMPORTANT� Use a soft cloth between these parts and the floor.� Do not use power tools above 8 volts to assemble.� Do not tighten all the screws until each part is properly assembled.
I
BC
STEP 2
Attach Back Stretcher (G) to Side Panel (B)with Cam Lock. (See Figure 2)
Attach Back Uprights (E) to Back Stretcher (G),then slide Back Panels (D) into place.
Attach Back Stretcher (F) to unit with Cam Lock.
Figure 2
F
G
EE
D
DD
B
Figure 1
STEP 1
Insert Cam Lock Screws into pre-drilled holes ofTop (A), Side Panels (B), (C) and Fixed Shelf (I).(See Figure 1)
A
Cam Lock Screw
Cam Lock Screw
Cam Lock Screw
Cam Lock
Cam Lock Screw
Cam Lock
Assembly Instructions 3/6
I
ML
H
Cam Lock
Cam Lock
Cam Lock
C
Cam Lock
STEP 3
Attach Fixed Shelf (I) to unit with Cam Locks.
STEP 4
Attach Middle Panels (L) and(M) to unit with Cam Locks.
Attach Front Stretcher (H)to unit with Cam Lock.
STEP 5
Attach Side Panel (C) to unit withCam Locks.
Assembly Instructions 4/6
Figure 4Figure 3
STEP 6
Insert Adjustable Pins intoside panels at desired level.
Place Shelves (J) and (K)into position.
Attach Doors (N) and (O) to unit bysliding door lift hinges into side panellift hinges. (See Figure 3)
Attach Knobs to Doors (N) and (O) withMachine Screws. (See Figure 4)
K
K
J
N
O
A
STEP 7
Attach Top (A) to unit with Cam Locks.
Adjustable Pin
Cam Lock
Assembly Instructions 5/6
STEP 8
Insert Wood Screws for Back Panelinto pre-drilled holes of unit.
STEP 9
Attach Hutch to Buffet with Steel PlateConnectors by inserting Wood Screwsfor Steel Plate Connector intopre-drilled holes. (See Figure 5)
Wood Screwfor Steel PlateConnector
Steel PlateConnector
Wood Screwfor Back Panel
Figure 5
Assembly Instructions 6/6
Hardware List
STEP 10
Place unit at desired location.
Drill a 3/8” hole in wall in-line withpre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall holeand attach Bracket with Wall Screw.
Attach Bracket at pre-drilled holeat top of unit with Wood Screw.
Move unit back into place.
Slide Tip-over Restraint throughBracket on wall and Bracket on unit.(See Figure 6)
Put tie end of Tip-over Restraint into lockend of Tip-over Restraint and pull until tight.
Anchor1 pc. (+1 extra)
Bracket2 pcs. (+1 extra)
M3.5x40Wall Screw1 pc. (+1 extra)
M3.5x16Wood Screw1 pc. (+1 extra)
Figure 6
Wood Screw
Wall ScrewBracketon wall
Anchor in wall
3/8” wall hole
Pre-drilled holeat top of unit
Tie end
Lock end
Bracket attop of unit
Tip-overRestraint
IMPORTANT� To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly.
Drill 3/8” hole in wall
Top of unit
Tip-over Restraint1 pc. (+1 extra)
NEVERuse glass cleaners on
finished furniture. Ammoniachemically attacks the finish.
allow liquids to remain on furniture.Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubberbased placemats.
PREVENTDISCOLORING
Do not use commercialwaxes and polishes.
PREVENTYELLOWING
Do not place hotobjects on surface.
PREVENTFINISH DAMAGE
Do not writedirectly on surface.
PREVENTMARKING
Do not use power toolsabove 8 volts to assemble.
PREVENTCRACKING
Do not placein direct sunlight.
PREVENTFADING
with a soft cloth moistenedin lukewarm soap and water.Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days ofpurchase. Digital images of the defective parts may be required. If the product was not purchased from an authorizedretail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembleditems nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,[email protected], 888-680-7460, 877-831-0319