Preconfiguration information (private network or VPN)

Item Topic Description

BARCODE Bar code Mandatory. This information can be obtained from the delivery

list or product label.

NETWORKING Networking scenario:

Private network and VPN:

private

Public network access

through IPSec: public

Mandatory

S_POE_RF1

S_POE_RF2

Status of TRX 1 or TRX 2:

1: enabled

0: Disabled

Optional. In PoE power supply mode, the BTS3900B only

supports one TRX. This information is used to disable the other

TRX.

S_BTSIP Static IP address of the BTS3900B Optional. In private network and VPN, this parameter should be

set when the static IP address of the BTS is required.

S_BTSIPMASK Subnet mask Optional. In private network and VPN, this parameter should be

set when the static IP address of the BTS is required.

S_GWIP IP addresses of the gateway Optional. In private network and VPN, this parameter should be

set when the static IP address of the BTS is required.

S_BSCIP Port IP address of the BSC Optional. In private network and VPN, this parameter should be

set when the static IP address of the BTS is required.

S_BSCIPMASK Subnet mask of the BSC Optional. In private network and VPN, this parameter should be

set when the static IP address of the BTS is required.

S_VLANSWITCH Whether the VLAN is enabled Optional. In private network and VPN, this parameter should be

set when the static IP address of the BTS is required.

S_VLANFLAG Value range of the VLAN ID: 2 to

4094

Optional. In private network and VPN, this parameter should be

set when the static IP address of the BTS is required.

S_VLANPRI Value range of the VLAN priority: 0

to 7

Optional. In private network and VPN, this parameter should be

set when the static IP address of the BTS is required.

Preconfiguration information (public network access through IPSe)

Item Topic Description

BARCODE Bar code Mandatory. This parameter can be obtained from

the delivery list or product label.

NETWORKING Networking scenario:

Private network and VPN:

private

Public network access

through IPSec: public

Mandatory

S_POE_RF1

S_POE_RF2

Status of TRX 1 or TRX 2:

1: enabled

0: Disabled

Optional. In PoE power supply mode, the BTS3900B

only supports one TRX. This parameter is used to

disable the other TRX.

IPADDR Static IP address of the BTS3900B Optional. In public network access through IPSec

mode, the static IP address of the BTS should be

set.

IPMASK Subnet mask of the BTS3900B IP

address

Optional

S_STATIC_IPGW Static IP gateway of the BTS3900B Optional. In public network access through IPSec

mode, the static IP gateway is used to configure

default route during the setting of BTS static IP

address.

DNS_Server DNS Optional

PSeGW_IP IP addresses of the PSeGW

PSeGW_DN Domain name of the PSeGW

Set either the IP address or the domain name.

When you choose to set the domain name, the DNS

should be configured in the network and properly

set.

M2000_DHCPServer_IP IP address of the M2000 DHCP server

M2000_DHCPServer_DN Domain name of the M2000 DHCP

server

Set either the IP address or the domain name.

When you choose to set the domain name, the DNS

should be configured in the network and properly

set.

GW_LOCAL_ID Type of IKE local authentication:

name: Indicates that the IKE

authentication is performed by the

domain name.

Mandatory. The type of the IKE local authentication

must be the same as the type of the IKE peer

authentication on the SeGW.

Item Topic Description

ip: Indicates that the IKE

authentication is performed by the IP

address.

GW_REMOTE_ID Type of the IKE peer authentication:

name: Indicates that the IKE

authentication is performed by the

domain name.

ip: Indicates that the IKE

authentication is performed by the IP

address.

Mandatory. The type of the IKE peer authentication

must be the same as the type of the IKE remote

authentication on the SeGW.

GW_LOCAL_NAME The IKE local name that is used during

the tunnel establishment with the

PSeGW

Optional

This parameter is configured only when

GW_LOCAL_ID is set to name. The IKE local name

must be the same as the IKE peer name on the

PSeGW.

GW_ROMOTE_NAME The IKE remote name that is used

during the tunnel establishment with

the PSeGW

Optional

This parameter is configured only when

GW_ROMOTE_ID is set to name. The IKE remote

name must be the same as the IKE local name on

the PSeGW.

GWS_LOCAL_NAME The IKE local name that is used during

the tunnel establishment with the BSC

SeGW

Optional

This parameter is configured only when

GW_LOCAL_ID is set to name. The IKE local name

must be the same as the IKE remote name on the

BSC SeGW.

GWS_REMOTE_NAME The IKE remote name that is used

during the tunnel establishment with

the BSC SeGW

Optional

This parameter is configured only when

GW_ROMOTE_ID is set to name. The IKE remote

name must be the same as the IKE local name on

the BSC SeGW.

PRE_SHARED_KEY Pre-shared key Mandatory

The key is used for authentication when an IPSec

tunnel is established with the PSeGW. The key must

be the same as that on the PSeGW.

Procedure

1. Connect the USB disk to the USB port of the BTS3900B directly or through a USB data cable. Check the status

of the RUN/ALM LED on the BTS3900B panel.

If ... Then ...

The RUN/ALM LED is green and blinks on for 0.125 s

and off for 0.125 s

It indicates that preconfiguration data file is being loaded

to the equipment.

2. WARNING:

3. When the RUN/ALM LED is green and blinks on for 0.125 s and off for 0.125 s, do not remove the USB disk.

4. After the preconfiguration file is loaded, wait one or two minutes. After the BTS is reset, check the status of the

RUN/ALM LED on the BTS3900B panel.

If ... Then ...

The RUN/ALM LED is green and blinks on for 1 s and off

for 1 s

It indicates that the BTS is running properly. Go to 3.

5. Remove the USB disk or USB data cable from the USB port on the side of the BTS3900B.

6. Check the transmission between the BTS3900B and the BSC on the LMT.