Bsod Error

8/7/2019 Bsod Error

1/13

BSOD Error : STOP: 00000000A | Error -IRQL_NOT_LESS_OR_EQUAL

Tech Advise :

Remove and Check any of the following devices:1. SCSI Devices2. IDE Devices3. Network Adapter4. Internal Modem & Sound Card5. Extra Hard Disks (You have to have at least one to complete the installation) 6. Cd Drive or DVD Drive (If you are installing from the local hard disk) 7. Upgrade Computer BIOS if possible

2. Check Event LogClick on start. Click on RunType - eventvwr.mscorClick on Start >> Control Panel >> Administrator Tools >> Event ViewerClick on Application(In vista click on windows Logs and then application)Here you need to look for red X with error reports. This will let you know what caused your pc to crash last time orprogram conflicting on your PC. Advisable to remove the program and then check if your PC works better or not.

3. Repair Windows to fixSTOP: 00000000A | Error - IRQL_NOT_LESS_OR_EQUALHow to Repair windows - Check this link on how to run windows repair

4. Check your RAMCheck If any of your RAM is malfunctioning. If you have 2 rams installed then try removing one them and reboot PC.Poor and damaged RAM can also cause such errors.

Fix BSOD Error : STOP: 000000050 | PAGE_FAULT_IN_NONPAGED_AREA

This Stop Error explains that requested data was not in memory. Defective memory (including mainmemoy, L2 RAM cache, video RAM) or incompatible software (including remote control and antivirussoftware) might cause this Stop error.Solution:

Hardware failure (memory, processor, or motherboard).

Anti-virus software that is running on your computer.Drivers installed by third-party software.Disable any antivirus running on your computer.STOP: 0x0000000a | STOP: 0x0000001e | STOP: 0x00000050

Uninstall software causing 000000050 page_fault_in_nonpaged_areaLook for software causing error in control panel >> Add remove programs >> Find the software anduninstall

BSOD Error - STOP: 00000001E | KMODE_EXCEPTION_NOT_HANDLED

This Stop error indicates that indicates that the Windows XP kernel detected an illegal or unknownprocessor instruction. The problem can be software or hardware related.

Solution:Hardware failure (memory, processor, or motherboard)Anti-virus software that is running on your computer.Drivers installed by third-party software.Disable any antivirus running on our computerSTOP: 0x0000000a | STOP: 0x0000001e | STOP: 0x00000050

8/7/2019 Bsod Error

2/13

BSOD Error STOP: 00000007B ,INACCESSIBLE_BOOT_DEVICE,Troubleshooting Stop 00000007B or 04,0,0,0 Error

Tech Advise:1

Please do the following steps to fix error

Registry

Caution : Incorrect Registry Editing can cause serious problems.Please be careful while editing registry or contact our supoprt team to fix it remotleyTech Advise:2Restore System.

Step1:Manually remove 00000007B Error

Restart the computer & go into BIOS configuration menu.In the BIOS settings change and revert back the SATA mode to original valueDoing this will allow system to get passed BSoD and boot up properly.

Restart the computer to boot into Windows Vista desktop.Exit all Windows-based programs.Click on Vista Start Menu & Click On Run ButtonIn the Open box type regedit in the Start Search box & then press ENTER.If you receive the User Account Control dialog box click Continue.Locate and then click the following registry subkeyHKEY_LOCAL_MACHINE\System\CurrentControlSet\Servic es\MsahciIn the right pane right-click Start in the Name column & then click Modify.In the Value data box type 0 and then click OK.On the File menu click Exit to close Registry Editor.Restart computer and enable ACHI mode in BIOS again.This time the computer should be able to boot up properly without error or BSoD.Step2: Tools and Software to remove BSOD ERROR 00000007B

Download Infection removal tools here

Step3: How to Uninstall software causing BSOD ERROR 00000007B

Look for software causing error in control panel >> Add remove programs

UninstallCausesCause Of Error BSOD Error || STOP: 00000007B | INACCESSIBLE_BOOT_DEVICE ||Troubleshooting Stop00000007B or 04,0,0,0 Error

The Cause of the problem can be due to the following reasonsThis error explain that Windows XP has lost access to the system partition or Boot Volume during start up.Installing or upgrading hardware drivers proab;ly caused this Stop Error. Setup has encountered a fatalerror that prevents it from continuing.This could also be caused by a Virus on PC

8/7/2019 Bsod Error

3/13

BSOD Error || Stop: 00000007F | UNEXPECTED_KERNEL_MODE_TRAP

Tech Advise:1

Run Check Disk Command

Fix Errors & Speed up through Chkdsk Command

Repair Hard Drive through check disk Command

Reboot Your PC, press F8 key continously while the PC is rebooting until a black window appears. Selectcommand prompt from the list. Now on the Dos window

Type

chkdsk c: /f /r

Enter

(you may get a prompt to press Y/N) Press Y which means that check disk command will run on net bootUP. Please allow the commad to run on next boot UP and

do not exit. This may take 30 min - 1hour.

NOTE: the /f command automatically fixes any errors encountered, the /r command locates bad sectorsand recovers readable information

This will definately help to fix any drive related errors and speed up Your PC performance

Tech Advise:2

If you added new hardware recently remove and replace it to determine if it is causing or contributing tothe problem.

Tech Advise:3

Registry

Caution : Incorrect Registry Editing can cause serious problems.Please be careful while editing registry or contact our supoprt team to fix it remotley

Please do the following steps to fix the BSOD STOP Error||00000007F |UNEXPECTED_KERNEL_MODE_TRAP

Click On Start Menu & Click On Run ButtonIn the boxType regedit

In the registry editor navigate to the subkey HKEY_LOCAL_MACHINE >>> SYSTEM >>>CurrentControlSet >>> Control >>> Session Manager >>> Memory Management.Double-click on PagedPoolSize and SystemPages to view the value for each entry.If PagedPoolSize is not zero assign a value of 0.If SystemPages is not zero assign a value of 40000 for systems with 128 MB or less of memory or 110000for systems with 128 MB to 256 MB of memory.For systems with more memory, do not increase the SystemPages value above 110000 without contactingMicrosoft technical support.Click OK & then close the registry editor.Restart your computer.

8/7/2019 Bsod Error

4/13

Causes:Cause Of Error BSOD Error || Stop: 00000007F | UNEXPECTED_KERNEL_MODE_TRAP

The Cause of the problem can be due to the following reasonsThis Stop Error shows a problem with Hardware caused by mismatched memory a malfunctioning CPUfailure with Fan causing overheating.Computer may have hardware or a Software problem.Faulty driver.

BSOD Error || STOP: 0x0000009F | DRIVER_POWER_STATE_FAILURETech Advise:1Check Devise Manager for any driver conflict. Update drivers.Tech Advise:2Roll Back Driver

Rolling Back Driver Might fix the problem

Click On Start Menu >> Right Click On My Computer >> Click On properties >>Device Manage r>>Double Click on DVD/CD ROM

Right Click On CD-ROM ATA Device

& then Right Click On Properties >> Click On Driver >> Click On Rollback Driver & then Click Ok.Causes

cause Of Error BSOD Error||STOP: 0x0000009F | DRIVER_POWER_STATE_FAILURE

The Cause of the problem can be due to the following reasons

This error indicates a malfunction of a driver.

This error generally occors while shutting down or moving out or standby or Hibernate Mode.

While Shutting down Suspending or resuming from Standby mode Suspending or resuming fromhibemation

BSOD Error || Stop: 0x000000D1 | DRIVER_IRQL_NOT_LESS_OR_EQUAL

Tech Advise:1

Increase Virtual memory.

Click On Start Menu >> Right-click On My Computer & then click Properties.

Click the Advanced tab >> Under Performance >> click Settings.

Click the Advanced tab >> Under Virtual Memory >> click Change.

Click No paging file.

Click OK >> click OK & then click OK.

Restart your computer.

Enable Page File again

8/7/2019 Bsod Error

5/13

Click On Start Menu >> Right-click My Computer & then click Properties.

Click the Advanced tab >> Under Performance >> click Settings.

Click the Advanced tab >> Under Virtual Memory >> click Change.

Click System managed sized

Click OK & then click OK.

Restart your computer.

Causes

Cause Of Error BSOD Error || Stop: 0x000000D1 | DRIVER_IRQL_NOT_LESS_OR_EQUAL


This Stop error indicates that the system attempted to access pageable memory using a kernel processIRQL that was too high.

The major cause is bad devise driver or by a faulty or mismatched RAM or damaged pagefile.

Damaged Virtual Memory Manager or RAM problems.

BSOD Error || STOP: 0x000000EA | THREAD STUCK IN DEVICE DRIVER

Tech Advise:1

Update your Video Adapter or install the latest Drivers for Windows XP.Replace your Video Card

Tech Advise:2

Please do the following steps to fix the error

Adjust the Hardware AccelerationClick On Start Menu >> Click On Control Panel >> & then double-click Display.On the Settings tab >> click On Advanced >> & then Click the Troubleshoot tab.Move the Hardware Acceleration slider to None >> & then click to clear the Enable write combining checkbox.Click OKCauses

Cause Of Error BSOD Error || STOP: 0x000000EA | THREADSTUCK IN DEVICE DRIVER

The Cause of the problem can be due to the following reasonsThis Error is caused by a devise driver causing the system to pause indefinitley. A hardware problem with the video AdapterOr a faulty video driver.This can indicate that there is a problem with the video hardware or that the graphics adaptercannot program the hardware correctly.

8/7/2019 Bsod Error

6/13

BSOD Error - STOP: 0x00000024 | Stop 0x24 or NTFS_FILE_SYSTEM

Tech Advise:1

Try disabling any virus scanning programs,

Tech Advise:2

Defrag Your PC.It is important to defrag your PC once a month to keep the performance of the PC up to date

Click on start >>> Programs >> System Tools >> Disk Defragmentor

CLick on Defrag Now

Defrag will help to clean any bad sectors on drive, increase disk space, speed up your PC performance

Tech Advise:3





Type

chkdsk c: /f /r

Enter





Tech Advise:4

Reconnect the drive that contains the corrupted NTFS volume.Restart the computer & then run the following command on the corrupted NTFS volume:chkdsk driveletter: /fAfter you use the Chkdsk tool to repair the corrupted NTFS volume, rename%SystemRoot%\System32\Drivers\NTFS.old to NTFS.SYS, and then shut down and restart the computer.

CAUSES:Cause Of Error STOP: 0x00000024 | Stop 0x24 or NTFS_FILE_SYSTEM

The Cause of the problem can be due to the following reasons This Stop error indicates that a problem occurred within NTFS.SYS, the driver file that allows the systemto read and write to

8/7/2019 Bsod Error

7/13

Drives formatted with the NTFS file system.A similar Stop message, 0x00000023 exists for the file allocation table FAT16 or FAT32 file systems.The NTFS.SYS file is the driver file that enables your computer to read and write to NTFS partitions.Damage in the NTFS file system, damaged portions of your hard disk or damaged SCSI or IDE drivers canalso Cause this issue.

BSOD Error - STOP : 0xC0000218 | UNKNOWN_HARD_ERROR - Stop: 0xc0000218 (Registry File Failure)

This error is caused when a registry hive file could not be loaded. The may be missing or corrupt. It may

be caused by hard disk failure or some other hardware problem.

Solution:1. Start your computer by running the Recovery Console, run the chkdsk /p command on the drive, andthen restart yourcomputer.2. When Windows loads, press SPACE BAR when the "Load Last Known Good" message appears.

BSOD Error || Stop 0x0000002E or DATA_BUS_ERROR

Tech Advise:1

Please do the steps to fix BSOD Error || Stop 0x0000002E or DATA_BUS_ERROR

Please verify that the RAM is the correct type for this installation & is correctly rated for speed voltage& other parameters required by your specific computer.If everything is correctcontact the manufacturer of your computers motherboard for BIOS updates.

Tech Advise:2

If your computer manufacturer provided a hardware test utilityuse it to diagnose which RAM module is bad.If you dont have a diagnostic application remove all but one RAM module and reboot your computer.

Tech Advise:3





Type

chkdsk c: /f /r

Enter



8/7/2019 Bsod Error

8/13



CAUSES:Cause Of Error BSOD Error || Stop 0x0000002E or DATA_BUS_ERROR


The cause is typically failed or defective RAM including motherboard Level 2 cache or video memoryincompatible or mismatched memory hardwareOr when a device driver attempts to access an address inThe 0x8xxxxxxx range that does not exist does not map to a physical addressA Stop 0x2E message can also indicate hard disk damage caused by viruses or other problems

BSOD Error || 0x0000003F or NO_MORE_SYSTEM_PTES

Tech Advise:1

Caution : Incorrect Registry Editing can cause serious problems.Please be careful while editing registry or contact our supoprt team to fix it remotley

To increase the number of PTEs allocated in the registryClick On Start Menu & then Click On Run ButtonIn the Run box type regedit

In the registry editor navigate to the subkey HKEY LOCAL MACHINE SYSTEM CurrentControlSet ControlSession Manager\Memory ManagementDouble click on PagedPoolSize and SystemPages to view the value for each entryIf PagedPoolSize is not zero assign a value of 0If SystemPages is not zero assign a value of 40000 for systems with 128 MB or less of memory or110000 for systems with 128 MB to 256 MB of memory

For systems with more memory do not increase the SystemPages value above 110000 without contactingMicrosoft technical support

Click OK and then close the registry editor

& Restart your computer

CAUSESCause Of Error BSOD Error || 0x0000003F or NO_MORE_SYSTEM_PTES


The system Page Table Entries PTE are depleted or fragmented due to the system performing a large

number of input output actions

A faulty device driver is not managing memory properly

An application such as a backup program is improperly allocating large amounts of kernel memory

8/7/2019 Bsod Error

9/13

BSOD Error || 0x00000077 or KERNEL_STACK_INPAGE_ERROR

Tech Advise:1

Please do the following steps to fix BSOD Error || 0x00000077 or KERNEL_STACK_INPAGE_ERROR

Step 1


To the Fix Errors



Type

chkdsk c: /f /r

Enter



NOTE: the /f command automatically fixes any errors encountered, the /r command locates bad sectorsand recovers readable informationStep 2

Scan and Remove boot sector virus

Causes

Cause Of Error BSOD Error || 0x00000077 or KERNEL_STACK_INPAGE_ERROR

The Cause of the problem can be due to the following reasonsDefective hardware

Bad sectors in the virtual memory paging file or a disk controller error In extremely rare cases depleted

nonpaged pool resources can cause this error.

BSOD Error || 0x00000079 or MISMATCHED_HAL

Tech Advise:1

Please do the following steps to fix BSOD Error || 0x00000079 or MISMATCHED_HAL Error

How to install Recovery Console

Please Insert the Windows XP CD into the CD-ROM drive.Click Start On & then click Run Button.In the Run Menu type d:\i386\winnt32.exe /cmdcons where d is the drive letter for the CD-ROM drive.In the case of 'Microsoft Windows XP Professional x64 Edition, type d:\amd64\winnt32.exe /cmdconswhere d is the drive letter for the CD-ROM drive.A Windows Setup Dialog Box appears. The Windows Setup Dialog Box describes the Recovery Consoleoption.

8/7/2019 Bsod Error

10/13

To confirm the installation click On Yes.Restart the computer.The next time that you start your computerMicrosoft Windows Recovery Console appears on the startup menu.

Start Windows XP by using the Recovery Console.

At the Recovery Console promptType the number of the older Windows operating system installation & then press ENTER.

For example type the number that corresponds to the Windows XP installation.Type the Administrator password & then press ENTER.Type c: & then press ENTER.Type ren ntldr oldntldr & then press ENTER.Insert the Windows Server 2003 CD-ROM into the CD-ROM or DVD-ROM drive.Type map & then press ENTER. Note the drive letter that is assigned to the CD-ROM or DVD-ROM drivethat contains the Windows Server 2003 CD-ROM.Type copy drive:\i386\ntldr (where drive is the letter of the CD-ROM or DVD-ROM drive that contains theWindows Server 2003 CD-ROM & then press ENTER.For example type copy d:\i386\ntldr, and then press ENTER.Type exit & then press ENTER to quit the Recovery Console.

CAUSE

Cause Of Error BSOD Error || 0x00000079 or MISMATCHED_HAL

The Cause of the problem can be due to the following reasonsThe Stop 0x79 message indicates that the hardware abstraction layer HAL and the kernel type for thecomputer do not matchThis error most often occurs when ACPI firmware settings are changed For example you might installWindows XP on an x86 basedcomputer with the firmware ACPI enable option enabled and later decide to disable it This error can alsoresult when mismatchedsingle and multi processor configuration files are copied to the system

BSOD Error || 0x0000007A or KERNEL_DATA_INPAGE_ERROR

Tech Advise:1

Step 1

Bad sectors in the virtual memory paging file disk controller error virus infection or memory hardwareproblemsThis problem might be fix through inrease virtual Memory

How to increase virtual memory.

For Windows XP

Click On Start Menu >> click Control Panel.Click On Performance & Maintenance >> click System.On the Advanced tab under Performance click On Settings.On the Advanced tab under Virtual memory click Change.Under Drive Volume Labelclick the drive that contains the paging file that you want to change.Under Paging file size for selected driveclick to Custom size check box.You can enter the amount of memory you would like to reserve for Virtual memory by entering the initial& maximum size.Click On SetWhen you are prompted to restart the computer click On Yes.

8/7/2019 Bsod Error

11/13

Step 2




Reboot Your PC, press F8 key continously while the PC is rebooting until a black window appears. Select

command prompt from the list. Now on the Dos window

Type

chkdsk c: /f /r

Enter





Step 3Reinstall Operating System

CausesCause Of Error 0x0000007A or KERNEL_DATA_INPAGE_ERROR


A page of kernel data was not found in the pagefile and could not be read into memoryThis might be due to incompatible disk or controller drivers firmware or hardware

BSOD Error || 0x000000C2 or BAD_POOL_CALLER

Tech Advise: 1

Roll Back Driver




& then Right Click On Properties >>Click On Driver>> Click On Rollback Driver & then Click Ok.

8/7/2019 Bsod Error

12/13

Step 1

Reboot the System.

Step 2

Remove the modem and Repair the OS

CAUSE

Cause Of Error BSOD Error || 0x000000C2 or BAD_POOL_CALLER


The Stop 0xC2 message indicates that a kernel-mode process or driver incorrectly attempted to performmemory operations

Faulty Driver or SoftwareFailing or Defective hardware

BSOD Error || Stop 0x000000CE or DRIVER_UNLOADED_WITHOUT

Step 1

Roll Back Driver





CAUSECause Of Error BSOD Error || Stop 0x000000CE or DRIVER_UNLOADED_WITHOUTThe Cause of the problem can be due to the following reasons

Installing faulty drivers or system services If a driver is listed by name

BSOD Error || Stop 0x000000ED or UNMOUNTABLE_BOOT_VOLUME

Tech Advise:

Run Check Disk to Fix the above error

Reboot your PC and press F8 key continously until Menu appears in DOS mode.Select command prompt from the list. Now in the command prompt typechkdsk c: /f /r(space after chkdsk & space after c: )EnterThis may take some time. You may get an error "windows cannot check the Disk- Do you want to run onreboot"Type Yes or YEnter

8/7/2019 Bsod Error

13/13

reboot

NOTE:The /f command will fix the errors. The r /r command finds bad sectors and recovers information which is readable. Areboot is required.

the /f command automatically fixes any errors encountered, the /r command locates bad sectors andrecovers readable information

Cause Of Error- Stop 0x000000ED or UNMOUNTABLE_BOOT_VOLUME


The error can be due to unexpected shut down or software conflict effecting the hard drive.Sometimes bacause of the cache not written to drive properly causingSometimes the contents of the cache are not written to the drive properly causing such errors ||BSOD Error - STOP : 0xC0000218 | UNKNOWN_HARD_ERROR - Stop: 0xc0000218 (Registry File Failure)

This error is caused when a registry hive file could not be loaded. The may be missing or corrupt. It maybe caused by hard disk failure or some other hardware problem.

Solution:1. Start your computer by running the Recovery Console, run the chkdsk /p command on the drive, andthen restart yourcomputer.

2. When Windows loads, press SPACE BAR when the "Load Last Known Good" message appears.

BSOD Error || 0x0000021A or STATUS_SYSTEM_PROCESS_TERMINATED

Tech Advise:1

Roll Back Driver


Click On Start Menu >> Right Click On My Computer >> Click On properties >>Device Manage r >> Double Click onDVD/CD ROM



Step 2Reboot the System.

Step 3Reinstall the Operating System

CAUSE

Cause Of Error BSOD Error || 0x0000021A or STATUS_SYSTEM_PROCESS_TERMINATED


Windows XP switches into kernel mode and a user mode subsystem such asWinlogon or the Client Server Runtime Subsystem CSRSS is compromised and security can no longer beguaranteed BecauseWindows XP cannot run without Winlogon or CSRSS this is one of the few situations where the failure of auser mode servicecan cause the system to stop responding

Bsod Error

Documents

Transcript of Bsod Error