Bromine Quick-Start Guide - · PDF file1. Start with a clean tub, and new or clean filter...
1
1. Start with a clean tub, and new or clean filter cartridge(s). (Use Spa System Flush when transitioning from any previous sanitizer.) 2. Fill spa with fresh water and operate circulating pump. 3. Test water with Bromine 4-in-1 test strips; adjust where necessary. 4. Add Natural Clarifier at the rate of 1 oz./500 gallons, weekly. 5. Add Metal Free stain/metal preventer per label instructions. 6. Shock water weekly with Oxy-Spa non-chlorine MPS shock at the rate of 1 ½ - 2 oz. per 500 gallons. (1 ½ tablespoons = approx. 2 oz.) 7. Add Granular Bromide Booster to establish an immediate bromide reserve or bank. 8. Add 3 - 4 Bromine Tablets to Float (brominator). Hold brominator underwater to remove air bubbles, then allow to float to surface. Maintain bromine at 3 - 5 ppm. Adjust release opening, more or less, as experience dictates over time. Add tablets as depleted. 9. Allow water to circulate to equilibrate spa chemicals for an hour or two (or overnight) then retest with test strips; readjust water balance if necessary. 10. Place and keep ZorbO in spa to absorb oil scum, replace every 3 - 6 months. NOTE: Follow instructions on each bottle according to your spa’s capacity guidelines. 2. Fill Spa & Circulate Water 3. Bromine 4-in1 Test Strips Test water 4. Add Natural Clarifier 5. Add Metal Free Shock Water with Oxy-Spa 6. 7. Add Granular Bromide Booster 8. Add 3 - 4 Bromine Tablets to Float 9. Circulate water for 1 - 2 hours and retest Bromine 4-in1 Test Strips 10. Place ZorbO in Spa (800) 823-3638 Mon-Fri 6 AM - 5 PM PST Water hardness: 150 - 300 ppm Bromine: 3.0 - 5.0 ppm Total Alkalinity: 80 - 120 ppm pH: 7.2 - 7.6 Recommended Chemical Levels START-UP PROCESS: TEST WATER WEEKLY. Bromine Quick-Start Guide WAIT 5 - 10 MINUTES WHEN ADDING DIFFERENT CHEMICALS! Adding too many chemicals at once can create cloudy water. 1. Clean Tub & New or Clean Filter(s)
Transcript of Bromine Quick-Start Guide - · PDF file1. Start with a clean tub, and new or clean filter...
1. Start with a clean tub, and new or clean filter cartridge(s). (Use Spa System Flush when transitioning from any previous sanitizer.)
2. Fill spa with fresh water and operate circulating pump.
3. Test water with Bromine 4-in-1 test strips; adjust where necessary.
4. Add Natural Clarifier at the rate of 1 oz./500 gallons, weekly.
5. Add Metal Free stain/metal preventer per label instructions.
6. Shock water weekly with Oxy-Spa non-chlorine MPS shock at the rate of 1 ½ - 2 oz. per 500 gallons. (1 ½ tablespoons = approx. 2 oz.)
7. Add Granular Bromide Booster to establish an immediate bromide reserve or bank.
8. Add 3 - 4 Bromine Tablets to Float (brominator). Hold brominator underwater to remove air bubbles, then allow to float to surface. Maintain bromine at 3 - 5 ppm. Adjust release opening, more or less, as experience dictates over time. Add tablets as depleted.
9. Allow water to circulate to equilibrate spa chemicals for an hour or two (or overnight) then retest with test strips; readjust water balance if necessary.
10. Place and keep ZorbO in spa to absorb oil scum, replace every 3 - 6 months.
NOTE: Follow instructions on each bottle according to your spa’s capacity guidelines.
2.
Fill Spa & Circulate Water
3.
TOTAL HARDNESS
TOTAL BROMINE
TOTAL ALKALNITY
pH
Bromine4-in1
Test Strips
Test water
4.
Add Natural Clarifier
5.
Add Metal Free
Shock Water with Oxy-Spa
6. 7.
Add Granular Bromide Booster
8.
Add 3 - 4 Bromine Tablets to Float
9.
Circulate water for 1 - 2 hours and retest
TOTAL HARDNESS
TOTAL BROMINE
TOTAL ALKALNITY
pH
Bromine4-in1
Test Strips
10.
Place ZorbO in Spa
(800) 823-3638Mon-Fri 6 AM - 5 PM PST
Water hardness: 150 - 300 ppm Bromine: 3.0 - 5.0 ppm Total Alkalinity: 80 - 120 ppm pH: 7.2 - 7.6
Recommended Chemical Levels
START-UP PROCESS:
TEST WATER WEEKLY.
Bromine Quick-Start Guide
WAIT 5 - 10 MINUTES WHEN ADDING DIFFERENT CHEMICALS! Adding too many chemicals at once can create cloudy water.
1.
Clean Tub & New or Clean Filter(s)
