S19-310, S19-310F, S19-310FSS, S19-310SBCombination Drench Shower/Eyewash Unit

Page 1 of 4This information is subject to change without notice. 11/26/2012

Emergency Fixtures Document No. 4490

• Exceeds American National Standard Z358.1 Specifications

• Galvanized Steel Protected with BradTect® Safety Yellow Coating or All Stainless Steel (S19-310FSS)

• Combination Units may be Top-Supplied or Mid-Supplied

• Universal Identification Sign and Inspection Tag Included

• Full, One-Year Warranty

• SpinTec™ showerheads are covered by one or more of the following patents: 8113446; D594,089; D669,555; Reg. Comm. Des. D001079560-0001. Other patents pending.

•Classified by Underwriters Laboratory Inc. to ANSI Z358.1

SpecificationsCombination Drench Shower/Eyewash Unit saves space and fits easily into any work environment. Shower valve operates quickly by a pull rod with a triangular handle. Shower provides a superior washdown with a more even spray pattern. Eyewash operated by a large, highly visible push handle. Safe, steady water flow under varying water supply conditions from 30–90 PSI is assured by integral flow control in the sprayhead assembly. NOTE: The ANSI Z358.1 standard requires an uninterruptible supply of flushing fluid at a minimum 30 PSI flowing pressure.

This plumbing fixture is not intended to dispense water for human consumption through drinking or for preparation of food or beverages.

®

S19-310

Recommended Option:Navigator S19-2100 EFX25

Emergency Thermostatic Mixing Valve

Satisfies ANSI Z358.1tepid water requirements.

S19-310F

S19-310FSS S19-310SB

Model Description S19-310 Drench Shower/Eyewash - Plastic Showerhead and Bowl

S19-310F Drench Shower/Eyewash - Stainless Steel Showerhead Shroud and Bowl

S19-310FSS Drench Shower/Eyewash - All Stainless Steel

S19-310SB Drench Shower/Eyewash - Plastic Showerhead and Stainless Steel Bowl

S19-2100 Navigator EFX25 - Emergency Thermostatic Mixing Valve

actoolsupply.com

actoolsupply.com

actoolsupply.com

Bradley S19-310FSS Stainless Steel Drench Shower Eye Wash

S19-310, S19-310F, S19-310FSS, S19-310SBCombination Drench Shower/Eyewash Unit

Page 2 of 4This information is subject to change without notice. 11/26/2012

Emergency Fixtures Document No. 4490

Standard EquipmentSpinTec™ Showerhead

Standard showerhead is 3.1" (78.7mm) diameter highly visible yellow impact-resistant plastic (Model S19-310F includes a 10¾" [273mm] diameter corrosion-resistant stainless steel shroud). High performance corrosion-resistant stainless steel showerhead measures 1½" (38mm) in diameter (S19-310FSS only). SpinTec drench showerhead features integral 22 GPM flow control, conserving water and helping to accurately size your tepid water system.

Shower ValveChrome-plated brass 1" NPT stay-open ball valve. Operated by a stainless steel rod with triangular handle. S19-310FSS is all stainless steel.

Eye Wash Bowl10" (254mm) diameter yellow impact-resistant plastic or 10¾" (273mm) diameter corrosion-resistant stainless steel.

Standard Sprayhead AssemblyChrome-plated brass sprayhead with twin soft-flow eyewash heads and protective sprayhead covers. Safe, steady water flow under varying water supply conditions from 30–90 PSI is assured by integral flow control in the sprayhead assembly. S19-310FSS is stainless steel.

Eyewash ValveChrome-plated brass ½" NPT stay-open ball valve. Hand operated by highly visible safety yellow PVC push handle. S19-310FSS is all stainless steel.

Pipe and Fittings1¼" galvanized steel with BradTect® safety yellow coating. S19-310BFSS is stainless steel.

Water Supply

1¼" NPT.

Local codes may require the installation of a backflow prevention valve

to complete proper installation. Compliance with local codes is the

responsibility of the installer. Valve must be tested annually to verify that

it is functioning properly. Backflow prevention valves are not included

with the fixture and may be supplied by the contractor or purchased from

Bradley Corporation.

SpinTec Flow Rate vs Inlet Pressure at Fixture

0

5

10

15

20

25

30

35

40

10 20 30 40 50 60 70 80 90

Inlet pressure at Fixture (psig)

Flo

w R

ate

(g

pm

)

actoolsupply.com

actoolsupply.com

S19-310, S19-310F, S19-310FSS, S19-310SBCombination Drench Shower/Eyewash Unit

Page 3 of 4This information is subject to change without notice. 11/26/2012

Emergency Fixtures Document No. 4490

Ø 9" (229mm) Flange with (3) Ø 3⁄8"

(10mm) Holes on Ø 8" (203mm) Bolt Circle

Top View From Bowl

6"(152mm)

9"(229mm)

Ø 10¾"(273mm)

253⁄8" (645mm)

85"(2159mm) to Bottom

of Base

25½"(648mm)

Ø 10¾"(273mm)

363⁄8" (924mm) to Bottom

of Base

55⁄8" (143mm)

10½" (267mm)

9½" (241mm)

66"(1676mm) to Bottom

of Base

6"(152mm)

Ø 9" (229mm) Flange with (3) Ø 3⁄8" (10mm)

Holes on Ø 8" (203mm) Bolt Circle

Top View From Bowl

9"(229mm)

253⁄8" (645mm)

86"(2184mm) to Bottom

of Base

68½"(1740mm) to Bottom

of Base

Ø 10"(254mm)

10½" (267mm)

9½" (241mm)

66"(1676mm) to Bottom

of Base

6"(152mm)

4½"(114mm)

Ø 3.1"(78.7mm)

941⁄8" (2391mm) to Bottom

of Base

42" (1067mm) to Bottom

of Base

363⁄8" (924mm) to Bottom

of Base

All dimensions assume standard thread engagement. Variations in manufacturing allow for +/- 1⁄8" (3mm) per threaded joint. To find the tolerance of a dimension, add the number of thread joints in between a dimension and multiply it by 1⁄8" (3mm).

Model S19-310 Model S19-310F

actoolsupply.com

actoolsupply.com

S19-310, S19-310F, S19-310FSS, S19-310SBCombination Drench Shower/Eyewash Unit

Page 4 of 4This information is subject to change without notice. 11/26/2012

Emergency Fixtures Document No. 4490

Ø 9" (229mm) Flange with (3) Ø 3⁄8" (10mm)

Holes on Ø 8" (203mm) Bolt Circle

Top View From Bowl

9"(229mm)

253⁄8" (645mm)

86"(2180mm) to Bottom

of Base

25½"(648mm)

Ø 10¾"(273mm)

363⁄8" (924mm) to Bottom

of Base

5½" (140mm)

10½" (267mm)

9½" (241mm)

66"(1676mm) to Bottom

of Base

6"(152mm)

4½"(114mm)

Ø 3.1"(78.7mm)

Ø 9" (229mm) Flange with (3) Ø 3⁄8"

(10mm) Holes on Ø 8" (203mm) Bolt

Circle

Top View From Bowl

9"(229mm)

26" (660mm)

25½"(648mm)

Ø 10¾"(273mm)

36" (914mm) to Bottom

of Base

5¾" (146mm)

10½" (267mm)

9½" (241mm)

66"(1676mm) to Bottom

of Base

6"(152mm)

85"(2159mm) to Bottom

of Base

3¾" (95mm)

1½" (38mm)

Model S19-310FSS

All dimensions assume standard thread engagement. Variations in manufacturing allow for +/- 1⁄8"(3mm) per threaded joint. To find the tolerance of a dimension, add the number of thread joints in between a dimension and multiply it by 1⁄8" (3mm).

Model S19-310SB

actoolsupply.com

actoolsupply.com