Bolting Catalog 2019 - SPX Flow · TORQUE WRENCHES MEASUREMENTS/ SPECIFICATIONS Torque Wrench...

10

TORQUE WRENCHES

Page

TORQUE WRENCH OVERVIEW…12-13

Page

TWSD…18-19 Square Drive Torque Wrench

Page

TWSD…20-21 Reactions Arms

Page

ADAPTERS & SOCKETS…22-23

Page

TWLC…30 Reactions Arms

Page

TWLC…31 Custom Accessories

Page

MEASUREMENT/ SPECIFICATIONS…11 Torque Wrench Selection Guide

Page

TWHC…14-15 High Cycle Torque Wrench

Page

TWHC…16-17 Reaction Arms

Page

TWLC…24-25 Drive Bodies

Page

TWL…26-29 Low Clearance Links

HIGH PERFORMANCE, BEST IN CLASS WRENCHES

Page

TWR…28-29 Low Clearance Reducers

Page

TWSL…32-33 SlimLine

spxboltingsystems.com 11

TORQUE WRENCHES MEASUREMENTS/ SPECIFICATIONS

Torque Wrench Selection Guide

Specifications and Dimensional Data

Additional torque may be required for loosening in certain situations:• Rust and corrosion: 2 X break out force• Heat Corrosion: 3 X break out forceOnly the smallest tool suitable for each application, under ideal conditions, is shown.Tools shown are a guideline only. Chart is not a replacement for calculations. Lubrication, corrosion, material type will all effect actual torque requirement. *TWSD1, TWSD3 and TWSD6 are obsolete and have been replaced by the TWHC Series.

Bolt Stud Size

Standard Hex Nut Size

Heavy Hex Nut Size Break Out Tool Make Up Tool

in mm in mm in mm TWHC TWSD TWLC TWHC TWSD TWLC

3/4 19 1-1/8 26 1-1/4 32 TWHC1 TWSD1 TWLC2 TWHC1 TWSD1 TWLC2

7/8 22 1-5/16 33 1-7/16 36 TWHC1 TWSD1 TWLC2 TWHC1 TWSD1 TWLC2

1 25 1-1/2 38 1-5/8 41 TWHC1 TWSD1 TWLC2 TWHC1 TWSD1 TWLC2

1-1/8 26 1-11/16 43 1-13/16 25 TWHC1 TWSD1 TWLC2 TWHC1 TWSD1 TWLC2

1-1/4 32 1-7/8 48 2 50 TWHC3 TWSD3* TWLC4 TWHC1 TWSD1 TWLC21-3/8 35 2-1/16 52 2-3/16 55 TWHC6 TWSD6* TWLC4 TWHC3 TWSD3* TWLC41-1/2 38 2-1/4 57 2-3/8 60 TWHC6 TWSD6* TWLC4 TWHC3 TWSD3* TWLC4

1-5/8 41 2-7/16 62 2-9/16 65 TWHC6 TWSD6* TWLC8 TWHC6 TWSD6* TWLC4

1-3/4 44 2-5/8 67 2-3/4 70 TWHC6 TWSD6* TWLC8 TWHC6 TWSD6* TWLC4

1-7/8 48 2-13/16 71 2-15/16 75

—

TWSD11 TWLC8 TWHC6 TWSD6* TWLC8

2 50 3 77 3-1/8 80 TWSD11 TWLC15

—

TWSD11 TWLC8

2-1/8 54 3-3/16 81 3-5/16 84 TWSD11 TWLC15 TWSD11 TWLC8

2-1/4 57 3-3/8 85 3-1/2 89 TWSD11 TWLC15 TWSD11 TWLC82-3/8 60 3-9/16 91 3-11/16 94 TWSD25 TWLC15 TWSD11 TWLC152-1/2 63 3-3/4 95 3-7/8 99 TWSD25 TWLC30 TWSD11 TWLC15

2-3/4 70 4-1/8 105 4-1/4 108 TWSD25 TWLC30 TWSD25 TWLC15

3 77 4-1/2 114 4 5/8 118 TWSD25 TWLC30 TWSD25 TWLC30

3-1/4 83 4-7/8 124 5 127 TWSD25 TWLC30 TWSD25 TWLC30

3-1/2 89 5-1/4 133 5 3/8 136 TWSD25 TWLC30 TWSD25 TWLC30

3-3/4 95 5-5/8 5-3/4 146 TWSD25 TWLC30 TWSD25 TWLC30

4 102 6 152 6 1/8 155 TWSD25 TWLC30 TWSD25 TWLC30

4-1/4 108

— —

6-1/2 159 TWHC50

— TWLC30 Upon Request

TWHC50

— TWLC30 Upon Request

4-1/2 114 6 7/8 175 TWHC50 TWHC50

4-3/4 120 7-1/4 184 TWHC50 TWHC50

5 127 7-5/8 193 TWHC50 TWHC50

12

TORQUE WRENCH OVERVIEW

TWLC

Multi way swivel allows easier positioning of the hoses on the job site.

Unique slide and shuttle piston design automatically engages without the need to manually rotate tool.

Patented rotating slide design adapts to angle against the piston, keeping forces normal in order to reduce wear and tear.

Fully enclosed components without use of a shroud which can bend and cause safety issues.

Pin is retained to the link body and will not fall out or get lost on the job site.

Steel body link with corrosion resistant nickel plating. Aluminum power head to reduce the overall weight of the tool.

Improved hardened steel reaction pad to protect the tool during torquing and modified radius to fit tighter applications.


TWHC

Push button feature allows quick and easy release and re-positioning of the reaction arm without any tools.

Multi-direction swivel allows operator to align the hoses in a convenient position, for any job!

Adaptable allen drive inserts for special applications, reference page 24.

With just a push of a button, the quick change square drive requires no tools to change from breakout to makeup.

14

TORQUE WRENCH - HIGH CYCLEQuality means Lower Cost of Ownership:• Designed for high cycle life: 2-3x more than existing

technology• Increased reliability: Simple drive assembly means

less downtime• Corrosion resistant material for use in harsh

environments

Enhanced Usability:• Compact nose radius allows the tool to fit in tighter,

hard-to-reach spaces• Low weight, high strength design• Fast operation, long stroke and optimum flow• Multi-direction high flow swivel manifold• Push button square drive reversal and reaction

arm positioning• Push-button release of square drive & reaction arm for

all models except TWHC50.

Designed with Safety in Mind:• Fully enclosed drive mechanism for operator safety• Swivel manifold internal relief valve prevents retract

side over-pressurization• Fine tooth pawl prevents tool ‘lock-on’

TORQUE WRENCH

HIGH CYCLE - TWHC Max Torque 71,816 Nm at 700 bar

(53,000 lb-ft at 10,000 psi)

NEW TECHNOLOGY TWHC CONVERSION CHART,SEE PAGE 122

1/4"NPT

STC

700 bar

TW HANDLE

• Robust steel construction with ribbed polymer grip• Multi-position on tool for balanced handling• Cap-screw locking with positive ‘docking’ • Is suitable for all wrench models (TWHC, TWSD,

TWLC), however for larger sizes (TWSD25/TWLC 30/TWHC50) we recommend the use of eye-bolt lifting.

Order No. Description Tool Ref

DFTAS000001 Wrench Handle Size 1

TWSD1TWSD3TWHC1TWHC3TWLC2

DFTAS000002 Wrench Handle Size 2

TWSD6TWSD11TWHC6TWLC4TWLC8TWLC15


Order No. DescriptionTWHC1 WrenchTWHC3 WrenchTWHC6 WrenchTWHC50 Wrench

Order No. DescriptionTWHC1H Wrench with handleTWHC3H Wrench with handleTWHC6H Wrench with handle

Order No. DescriptionDFTAS000001 Handle for TWHC1DFTAS000001 Handle for TWHC3DFTAS000002 Handle for TWHC6


Ordering Information

E

A

DG

F

B

I*

C

H

TWHC

Tool ModelMin Torque Max Torque Square

DriveA B C D E F G H I

Weightmm mm mm mm mm mm mm mm

Nm lb-ft Nm lb-ft in (in) (in) (in) (in) (in) (in) (in) (In) Kg lb

TWHC1 230 170 1, 915 1,413 3/4 132(5.20)

145(5.71)

28(1.10)

111.5(4.39)

170.0(6.69)

39.5(1.56)

67.7(2.67)

86.1(3.39) M6 x 1.0 2.8 6.2

TWHC3 510 376 4,249 3,136 1 165(6.50)

173.5(6.83)

36.5(1.44)

129.6(5.10)

197.7(7.78)

53(2.09)

83.7(3.30)

105.1(4.14) M6 x 1.0 5.3 11.7

TWHC6 984 726 8,198 6,050 1-1/2 192(7.56)

201.6(7.94)

44(1.73)

158.5(6.24)

243.7(9.59)

61(2.40)

99.9(3.93)

135.1(5.32) M8 x 1.25 8.8 19.4

TWHC50 8,628 6,360 71,816 53,000 2-1/2 404.5(15.93)

356.6(14.04)

88(3.46)

266.5(10.49)

446.6(17.58)

115(4.53)

192.2(7.57)

258(10.16) M12 x 1.75 69 152

* Dimension I shows thread size (on both sides of the tool) for safety handle or lifting point. TWHC50 model available with lifting points only.

16

TORQUE WRENCH

REACTIONS ARMS - TWHC

L3

L1

L2

(STD ARM)

(TWHC#-ERA1)

(TWHC#-ERA2)(TWHC#-ERA3) L4

(STD

ARM

)

(TW

HC#-

ERA1

)

(TW

HC#-

ERA2

)

(TW

HC#-

ERA3

)

TWHC EXTENDED REACTION ARM TWHC-ERA

• Long reach version of TWHC standard reaction arm• 3 standard sizes per model (+25mm/50mm/75mm)

(+1 in / 2 in / 3 in), specials upon request• Replaces standard reaction arm – quick release

pin locking• Steel alloy construction• 360° rotation• Available for full range of tool sizes

Tool Ref Order No.L1 L2 L3 L4 Weight

mm in mm in mm in mm in kg lb

TWHC1TWHC1-ERA1 137 5.39 111 4.37

60 2.36 30 1.182 4.4

TWHC1-ERA2 162 6.38 136 5.35 2.3 5.1TWHC1-ERA3 187 7.36 161 6.34 2.6 5.7

TWHC3TWHC3-ERA1 155 6.10 130 5.12

70 2.76 35 1.383 6.6

TWHC3-ERA2 180 7.09 155 6.10 3.5 7.7TWHC3-ERA3 205 8.07 180 7.09 3.9 8.6

TWHC6TWHC6-ERA1 184 7.24 161 6.34

95 3.74 40 1.575 11

TWHC6-ERA2 209 8.23 186 7.32 5.6 12.4TWHC6-ERA3 234 9.21 211 8.31 6.2 13.7


The tool’s designed long-stroke mechanism imparts a minimum 30 degree nut rotation per stroke while maintaining a tight and compact nose radius: this is a clear advantage over the short stroke and back-up pawl mechanisms of light alloy competitive models. Fewer parts and reduced torsion in operation - equals reduced wear, maintenance and associated costs.

HANDLES SOLD SEPARATELY

OK FOR SUBSEA


TWHC REACTION PAD TWHC-RP

• Wrench In-Line Reaction Pad for TWHC wrench: used as simple pad or modified platform for specific application (Machine-able/Weld-able platform)

• Replaces standard reaction arm – quick release pin locking

• Steel alloy construction • 360 degree rotation• Available for full range of tool sizes

TWHC LONG REACTION ARMTWHC-LRA

• Tubular extension arm for TWHC wrench: in-line reaction outside wrench profile


• Steel/light alloy construction (reaction flat machined on tube end)

• Can be cut down to suit specific length• Available for full range of tool sizes

L2

L1

L3

WIDTH

L1L2

Tool Ref Order No.L1 L2 L3 Width Weight

mm in mm in mm in mm in kg lbTWHC1 TWHC1-RP 72 2.835 116 4.567 49 1.93 64 2.52 1 2.2TWHC3 TWHC3-RP 86 3.39 138 5.43 55 2.17 76 2.99 1.5 3.3TWHC6 TWHC6-RP 99 3.90 162 6.38 62 2.44 89 3.50 2.3 5.1

Tool Ref Order No.L1 L2 Weight

mm in mm in kg lbTWHC1 TWHC1-LRA

501 19.72 152 64.5 9.9

TWHC3 TWHC3-LRA 6 13.2TWHC6 TWHC6-LRA 8.1 17.9



18

SQUARE DRIVE TORQUE WRENCH• Low weight, high strength design• Superior torsional strength• Fast operation cycle• Fine tooth ratchet• Floating piston design• Swivel manifold internal relief valve prevents retract

side over-pressurization• Rigid steel body construction• Compact frame size• Reaction and drive accessories available

360° Reaction Arm

TORQUE WRENCH

SQUARE DRIVE - TWSDMax Torque 33,198 Nm at 700 bar

(24,500 lb-ft at 10,000 psi)

OK FOR SUBSEA

1/4"NPT

STC

700 bar

TWSD CONVERSION CHART,SEE PAGE 120


L1

L2

W2

W1R

H1

L3

• Push button reversal of square drive• Corrosion resistant finish• 360˚ reaction arm• Push to lock reaction arms• Multi-axis high flow swivel manifold• Simple design• Consistently accurate torque output• Fully enclosed drive mechanism

Order No. DescriptionTWSD11 WRENCH - 14,823 Nm , 10,940 lb-ftTWSD25 WRENCH - 33,198 Nm , 24,500 lb-ft

Standard Reaction Arm included for all models

Order No. DescriptionDFTAS000002 WRENCH HANDLE Size 2 Tool Ref. TWSD11

TWSD



Tool ModelSquare Drive Min Torque Max. Torque Tool Weight

in Nm lb-ft Nm lb-ft kg lb

TWSD11 1-1/2 1,780 1,313 14,823 10,940 13.1 28.9

TWSD25 2-1/2 3,984 2,940 33,198 24,500 29.5 65.0

Tool ModelL1 L2 L3 H1 R W1 W2

mm in mm in mm in mm in mm in mm in mm in

TWSD11 234 9.2 292 11.5 178 7.0 241 9.5 56 2.2 61 2.4 165 6.5

TWSD25 305 12 376 14.8 231 9.1 315 12.4 71 2.8 76 3.0 200 7.9

20

TORQUE WRENCH

REACTION ARMS - TWSD

L3

L1

L2

(STD ARM)

(TWSD#-ERA1)

(TWSD#-ERA2)(TWSD#-ERA3) L4

(STD

ARM

)

(TW

SD#-

ERA1

)

(TW

SD#-

ERA2

)

(TW

SD#-

ERA3

)

TWSD EXTENDED REACTION ARM TWSD-ERA

• Long reach version of TWSD standard reaction arm• 3 standard sizes per model (+25mm/50mm/75mm)

(+1 in / 2 in / 3 in), specials upon request• Replaces standard reaction arm – quick release

pin locking• Steel alloy construction• 360° rotation• Available for full range of tool sizes


mm in mm in mm in mm in kg lb

TWSD11TWSD11-ERA1 204 8.03 190 7.48

110 4.33 40 1.578 17.6

TWSD11-ERA2 229 9.02 215 8.46 8.5 18.7TWSD11-ERA3 254 10 240 9.45 9.5 20.9

TWSD25TWSD25-ERA1 256 10.08 225 8.86

1455.71 50 1.97

18 39.7TWSD25-ERA2 281 11.06 250 9.84 20 44.1TWSD25-ERA3 306 12.05 275 10.83 147 21 46.3


Mechanical PullerSelection

Optional CylindersTorque Wrench Handle

SEE PAGE 14


TWSD REACTION PAD TWSD-RP

• Wrench In-Line Reaction Pad for TWSD wrench: used as simple pad or modified platform for specific application (Machine-able/Weld-able platform)


• Steel alloy construction • 360 degree rotation• Available for full range of tool sizes

TWSD LONG REACTION ARMTWSD-LRA

• Tubular extension arm for TWSD wrench: in-line reaction outside wrench profile


• Steel/light alloy construction (reaction flat machined on tube end)

• Can be cut down to suit specific length• Available for full range of tool sizes

L2

L1

L3

WIDTH

501.0 (19.72")152.0 (6.0")

Tool Ref Order No.L1 L2 L3 Width Weight

mm in mm in mm in mm in kg lbTWSD11 TWSD11-RP 109,5 4.311 184,5 7.264 65,5 2.579 105 4.133 4 8.8TWSD25 TWSD25-RP 136,5 5.374 243,5 9.587 88,5 3.484 143 5.630 10 22

Tool Ref Order No.L1 L2 Weight

mm in mm in kg lbTWSD11 TWSD11-LRA

501 19.72 152 611 24.3

TWSD25 TWSD25-LRA 22 48.5



22

SQUARE DRIVE

ADAPTERS & SOCKETS

Male Hex Drive Hexagon

Order No.Hexagon

Order No.Wrench Drive Size Drive Size

Size A/F (inch) TWSD TWHC A/F (mm) TWSD TWHC

1(TWHC1)

5/8 TWHCHD01-063 17mm TWHCHD01-0173/4 TWHCHD01-075 19mm TWHCHD01-0197/8 TWHCHD01-088 22mm TWHCHD01-0221 TWHCHD01-100 24mm TWHCHD01-024

27mm TWHCHD01-027

3(TWHC3)


1-1/8 TWHCHD03-113 27mm TWHCHD03-0271-1/4 TWHCHD03-125 30mm TWHCHD03-0301-3/8 TWHCHD03-138 32mm TWHCHD03-0321-1/2 TWHCHD03-150 36mm TWHCHD03-0361-5/8 TWHCHD03-163 41mm TWHCHD03-041

6(TWHC6)


1-1/8 TWHCHD06-113 27mm TWHCHD06-0271-1/4 TWHCHD06-125 30mm TWHCHD06-0301-3/8 TWHCHD06-138 32mm TWHCHD06-0321-1/2 TWHCHD06-150 36mm TWHCHD06-0361-5/8 TWHCHD06-163 41mm TWHCHD06-041

11(TWSD11)

1-1/8 TWD11-113 27mm TWD11-0271-1/4 TWD11-125 30mm TWD11-0301-3/8 TWD11-138 32mm TWD11-0321-1/2 TWD11-150 36mm TWD11-0361-5/8 TWD11-163 41mm TWD11-0411-3/4 TWD11-175 46mm TWD11-046

25(TWSD25)

1-1/2 TWD25-150 36mm TWD25-0361-5/8 TWD25-163 41mm TWD25-0411-3/4 TWD25-175 46mm TWD25-0461-7/8 TWD25-188 50mm TWD25-050

2 TWD25-200 55mm TWD25-0552-1/4 TWD25-225 60mm TWD25-0602-1/2 TWD25-250 65mm TWD25-0652-3/4 TWD25-275 70mm TWD25-070

Customs sizes are available upon request


Impact Sockets - Imperial (for TWHC & TWSD)Socket Size 3/4" Drive 1" Drive 1-1/2" Drive 2-1/2" Drive

Imperial Order No. Order No. Order No. Order No.7/8" TWSIA088 TWSIB088 — —

1-1/16" TWSIA106 TWSIB106 — —1-1/4" TWSIA125 TWSIB125 — —1-3/8" TWSIA138 TWSIB138 — —1-7/16" TWSIA144 TWSIB144 — —1-5/8" TWSIA163 TWSIB163 TWSIC163 —

1-13/16" TWSIA181 TWSIB181 - —2" TWSIA200 TWSIB200 TWSIC200 —

2-3/16" TWSIA219 TWSIB219 TWSIC219 —2-3/8" TWSIA238 TWSIB238 TWSIC238 —2-9/16" — TWSIB256 TWSIC256 —2-3/4" — TWSIB275 TWSIC275 —

2-15/16" — TWSIB294 TWSIC294 —3-1/8" — TWSIB313 TWSIC313 TWSIF3133-3/8" — TWSIB338 TWSIC338 TWSIF3383-12" — TWSIB350 TWSIC350 TWSIF3503-3/4" — TWSIB375 TWSIC375 TWSIF3753-7/8" — TWSIB388 — TWSIF3884-1/8" — TWSIB413 TWSIC413 TWSIF4134-1/4" — TWSIB425 TWSIC425 TWSIF4254-5/8" — — TWSIC463 TWSIF463

5" — — — TWSIF5005-3/8" — — — TWSIF5385-3/4" — — — TWSIF5756-1/8" — — — TWSIF613

Impact Sockets - Metric (for TWHC & TWSD)Socket Size 3/4" Drive 1" Drive 1—1/2" Drive 2—1/2" Drive

Metric Order No. Order No. Order No. Order No.22mm TWSMA022 TWSMB022 — —24mm TWSMA024 TWSMB024 — —32mm TWSMA032 TWSMB032 — —36mm TWSMA036 TWSMB036 — —41mm TWSMA041 TWSMB041 TWSMC041 —46mm TWSMA046 TWSMB046 — —50mm TWSMA050 TWSMB050 — —55mm — TWSMB055 — —60mm — TWSMB060 TWSMC060 —65mm — TWSMB065 TWSMC065 —70mm — TWSMB070 TWSMC070 —75mm — TWSMC075 —80mm — TWSMB080 TWSMC080 TWSMF08085mm — TWSMB085 TWSMC085 TWSMF08590mm — TWSMB090 TWSMC090 TWSMF09095mm — TWSMB095 TWSMC095 TWSMF095100mm — TWSMB100 — TWSMF100110mm — TWSMB110 TWSMC110 TWSMF110115mm — — TWSMC115 TWSMF115120mm — — TWSMC120 —135mm — — — TWSMF135150mm — — — TWSMF150

For Long Reach (Extended Length) sockets add “LR” to the end of the part number. For 12 point (bi-hex) sockets, add “BH” to the end of the part number.

24

TORQUE WRENCH LOW CLEARANCEThe TWLC Series Wrench was designed for the most inaccessible bolting areas found in the industry. Its long neck, short height and small radius have all added to its great success.

TORQUE WRENCH

LOW CLEARANCE - TWLCMax Torque 39,024 Nm at 700 bar

(28,800 lb-ft at 10,000 psi)

Drive Body

Combine a drive body with a link to make a wrench. Each are sold separately.

Several link sizes are available for each drive.

1/4"NPT

STC

700 bar

OK FOR SUBSEA

TWSD CONVERSION CHART,SEE PAGE 121

Mechanical PullerSelection

Optional CylindersTorque Wrench Handle

SEE PAGE 14


I

G

H

J

AB

E

C

F

D

• Low weight, high strength design• Superior torsional strength• Fast operation cycle• Fine tooth ratchet• Floating piston design• Link pin does not fall out• Auto-connect drive piston• Compact frame size• Rigid steel body construction• Swivel manifold internal relief valve prevents

retract side over-pressurization

• “Hardened” steel reaction pad on TWLC8, 15 & 30

• Small nose radius• Corrosion resistant finish• Multi-axis high flow swivel manifold• Simple design• Consistent torque output

TWLC


Body Order No.

A B C D E F G H

mm in mm in mm in mm in mm in deg mm in mm in

TWLC2 136 5.4 103 4.1 128 5 8 0.3 35 1.4 13 32 1.3 42 1.7

TWLC4 163 6.4 130 5.1 159 6.3 9 0.4 43 1.7 13 42 1.7 52 2

TWLC8 195 7.7 158 6.2 177 7 24.5 1 40 1.6 14 54 2.1 67 2.6

TWLC15 223 8.8 186 7.3 200 7.9 27 1.1 43 1.7 14 63 2.5 76 3

TWLC30 276 10.9 239 9.4 267 10.5 26 1 62 2.4 15 82 3.2 94 3.7

Body Order

No.Hex Range Min Torque Max Torque Weight (Body Only)

mm mm in in Nm lb-ft Nm lb-ft kg lb

TWLC2 26 60 1 2-3/8 256 189 2,134 1,575 1.0 2.2

TWLC4 33 80 1-5/16 3-1/8 646 477 5,386 3,975 2.0 4.4

TWLC8 49 100 1-7/8 3-15/16 1,293 954 10,772 7,950 3.5 7.7

TWLC15 62 116 2-7/16 4-5/8 2,415 1,782 20,122 14,850 7.0 15.4

TWLC30 80 155 3-1/8 6-1/16 4,683 3,456 39,024 28,800 14.5 31.9

TO SPECIFY A TWLC SOLUTION:1. Find a link for your application (nut size) (page 25-27)2. Choose the appropriate Drive body (page 23)3. Add reducers for additional nut sizes (pages 26-29)Please order Drive Body and Link separately and pay attention to the same size, for Example TWLC2 and TWL2-041.


CAUTION: Always read operating manual before using for proper use of tools and accessories.NOTE: Reference dimensions shown and vary by links size. Exacting dimensions can be found on our website.

• Quick interchangeable heads, no tools necessary• Replaceable reaction pad on larger models

Radius

26

TORQUE WRENCH

LOW CLEARANCE LINKS - TWLC Parts Codes, Nose Radius

TWLC2 TWLC4 TWLC8

Nut A/F Link Order No.

Radius R I J Weight

(Link Only) Link Order No.

Radius R I J Weight


Radius R I J Weight

(Link Only)

Inch Metric mm (in)

mm (in)

mm (in)

kg (lb)

mm (in)

mm (in)

mm (in)

kg (lb)

mm (in)

mm (in)

mm (in)

kg (lb)

1 26 TWL2-026

31.5(1.2)

180(7.1)

38(1.5)

2(4.4)

1-1/16 27 TWL2-0271-1/8 29 TWL2-0291-3/16 30 TWL2-0301-1/4 32 TWL2-0321-5/16 33 TWL2-033 TWL4-033

36.5(1.4)

227(8.9)

53 (2.1)

4(8.8)

1-3/8 35 TWL2-035 TWL4-0351-7/16 36 TWL2-036 TWL4-0361-1/2 38 TWL2-150

34.5(1.4)

181(7.1)

40(1.6)

2(4.4)

TWL4-1501-9/16 40 TWL2-040 TWL4-0401-5/8 41 TWL2-041 TWL4-041

1-11/16 43 TWL2-04337

(1.5)183(7.2)

40(1.6)

2(4.4)

TWL4-04339

(1.5)227(8.9)

53(2.1)

4(8.8)1-3/4 44 TWL2-044 TWL4-044

1-13/16 46 TWL2-046 TWL4-0461-7/8 48 TWL2-188

40(1.6)

185(7.3)

43(1.7)

2(4.4)

TWL4-18842

(1.7)227(8.9)

53(2.1)

4(8.8)

TWL8-188

50.5(2.0)

274(10.8)

77(3.0)

7(15.4)

1-15/16 49 TWL2-049 TWL4-049 TWL8-0492 50 TWL2-050 TWL4-050 TWL8-050

2-1/16 52 TWL2-05242.5(1.7)

185(7.3)

43(1.7)

2(4.4)

TWL4-05244.5(1.8)

227(8.9)

53(2.1)

4(8.8)

TWL8-0522-1/8 54 TWL2-054 TWL4-054 TWL8-0542-3/16 55 TWL2-055 TWL4-055 TWL8-0552-1/4 57 TWL2-057

45.5(1.8)

185(7.3)

43(1.7)

2(4.4)

TWL4-22547.5(1.9)

227(8.9)

53(2.1)

4(8.8)

TWL8-0572-5/16 59 TWL2-059 TWL4-059 TWL8-0592-3/8 60 TWL2-060 TWL4-060 TWL8-0602-7/16 62 TWL4-062

50(2.0)

227(8.9)

53(2.1)

4(8.8)

TWL8-06253

(2.1)274

(10.8)77

(3.0)7.5

(16.5)2-1/2 63 TWL4-063 TWL8-0632-9/16 65 TWL4-065 TWL8-0652-5/8 67 TWL4-067

53(2.1)

229(9.0)

56(2.2)

4(8.8)

TWL8-06756

(2.2)274

(10.8)77

(3.0)7.5

(16.5)2-11/16 68 TWL4-068 TWL8-0682-3/4 70 TWL4-070 TWL8-070

2-13/16 71 TWL4-07155.5(2.2)

229(9.0)

56(2.2)

4.5(9.9)

TWL8-07158.5(2.3)

274(10.8)

77(3.0)

7.5(16.5)2-7/8 73 TWL4-073 TWL8-073

2-15/16 75 TWL4-075 TWL8-0753 77 TWL4-077

59(2.3)

230(9.1)

58(2.3)

4.5(9.9)

TWL8-07762

(2.4)277

(10.9)72

(2.8)8

(17.6)3-1/16 78 TWL4-313 TWL8-3133-1/8 80 TWL4-080 TWL8-0803-3/16 81 TWL8-081

67(2.6)

277(10.9)

72(2.8)

8(17.6)

3-1/4 83 TWL8-0833-5/16 84 TWL8-0843-3/8 85 TWL8-0853-7/16 87 TWL8-087

89 TWL8-0893-1/2 90 TWL8-0903-9/16 91 TWL8-091

73.5 (2.9)

277 (10.9) 72 (2.8) 8

(17.6)

3-5/8 92 TWL8-0923-11/16 94 TWL8-0943-3/4 95 TWL8-095

3-13/16 97 TWL8-09799 TWL8-388

3-7/8 100 TWL8-100

R

MO

RE

SO

LUTI

ON

S O

N N

EX

T P

AG

E

NOTE:The sizes listed on these pages encompass both heavy hex and standard hex nut sizes. Check your local SPX FLOW Bolting Office for availability as some items may be special order.


TWLC15 TWLC30


Radius R I J Weight


Radius R I J Weight

(Link Only)

Inch Metric mm (in)

mm (in)

mm (in)

kg (lb)

mm (in)

mm (in)

mm (in)

kg (lb)

2-7/16 62 TWL15-062

60.5(2.4)

313(12.3)

88(3.5)

12.5(27.5)

2-1/2 63 TWL15-0632-9/16 65 TWL15-0652-5/8 67 TWL15-067

2-11/16 68 TWL15-0682-3/4 70 TWL15-070

2-13/16 71 TWL15-07163

(2.5)313

(12.3)88

(3.5)12.5

(27.5)2-7/8 73 TWL15-0732-15/16 75 TWL15-075

3 77 TWL15-07766.5(2.6)

313(12.3)

88(3.5)

13(28.6)3-1/16 78 TWL15-313

3-1/8 80 TWL15-080 TWL30-080

77(3.0)

393(15.5)

104(4.1)

26.5(58.3)

3-3/16 81 TWL15-081

72(2.8)

313(12.3)

80(3.1)

13.5(29.7)

TWL30-0813-1/4 83 TWL15-083 TWL30-0833-5/16 84 TWL15-084 TWL30-0843-3/8 85 TWL15-085 TWL30-0853-7/16 87 TWL15-087 TWL30-087

89 TWL15-089 TWL30-0893-1/2 90 TWL15-090 TWL30-0903-9/16 91 TWL15-091

78(3.1)

316 (12.4)

80(3.1)

13.5(29.7)

TWL30-091

83(3.3)

393(15.5)

104(4.1)

26.5(58.3)

3-5/8 92 TWL15-092 TWL30-0923-11/16 94 TWL15-094 TWL30-0943-3/4 95 TWL15-095 TWL30-095

3-13/16 97 TWL15-097 TWL30-097 99 TWL15-388 TWL30-388

3-7/8 100 TWL15-100 TWL30-1004 102 TWL15-102

82.5(3.2)

316(12.4)

80(3.1)

14(30.8)

TWL30-102

89(3.5)

393(15.5)

104(4.1)

27.5(60.5)

4-1/16 103 TWL15-103 TWL30-1034-1/8 105 TWL15-105 TWL30-1054-3/16 106 TWL15-106 TWL30-1064-1/4 108 TWL15-425 TWL30-4254-5/16 110 TWL15-110

87.5 (3.4)

316(12.4)

80(3.1)

14(30.8)

TWL30-1104-3/8 111 TWL15-111 TWL30-111

92(3.6)

393(15.5)

104(4.1)

27.5(60.5)

4-7/16 113 TWL15-113 TWL30-1134-1/2 114 TWL15-114 TWL30-114

115 TWL15-115 TWL30-1154-9/16 116 TWL15-116 TWL30-1164-5/8 117 TWL15-463 TWL30-463

4-11/16 119 TWL30-119 99(3.9)

400(15.7)

109(4.3)

28.5(62.7)4-3/4 120 TWL30-120

TWLC30 (Continued)


Radius R I J Weight

(Link Only)

Inch Metric mm (in)

mm (in)

mm (in)

kg (lb)

4-13/16 122 TWL30-122

99(3.9)

400 (15.7)

109(4.3)

28.5(62.7)

123 TWL30-1234-7/8 124 TWL30-124

4-15/16 125 TWL30-1255 127 TWL30-500

5-1/16 129 TWL30-129

105(4.1)

400(15.7)

109(4.3)

28.5(62.7)

5-1/8 130 TWL30-1305-3/16 132 TWL30-1325-1/4 133 TWL30-1335-3/8 135 TWL30-135

137 TWL30-5385-7/16 138 TWL30-138

110(4.3)

400(15.7)

109(4.3)

28.5(62.7)

5-1/2 140 TWL30-1405-9/16 141 TWL30-1415-5/8 143 TWL30-143

5-11/16 144 TWL30-1445-3/4 145 TWL30-145

146 TWL30-1465-13/16 148 TWL30-148

116(4.6)

400(15.7)

109 (4.3)

29.5(64.9)

5-7/8 149 TWL30-149150 TWL30-150

5-15/16 151 TWL30-1516 152 TWL30-152

6-1/16 154 TWL30-1546-1/8 155 TWL30-155

R

MO

RE

SO

LUTI

ON

S O

N N

EX

T P

AG

E



12 point links available upon request. Please contact factory.

28

TORQUE WRENCH

LOW CLEARANCE REDUCERS - TWLC

Drive Body, Links & Reducers

Special sizes available upon request.

Body Reference Nut A/F Reducer Reducer Reducer

Order No. Link No. mm in mm in Order No. mm in Order No. mm in Order No.

TWLC2

TWL2-032 32 1-1/4 – – – – – – – – –

TWL2-036 36 1-7/16 – – – – – – – – –

TWL2-041 41 1-5/8 41-36 1-5/8 – 1-7/16 TWR2-041036 41-32 1-5/8 – 1-1/4 TWR2-041032 – – –

TWL2-046 46 1-13/16 46-41 1-13/16 – 1-5/8 TWR2-046041 46-36 1-13/16 – 1-7/16 TWR2-046036 46-32 1-13/16 – 1-1/4 TWR2-046032

TWL2-050 50 2 50-46 2 – 1-13/16 TWR2-050046 50-41 2 – 1-5/8 TWR2-050041 50-36 2 – 1-7/16 TWR2-050036

TWL2-055 55 2-3/16 55-50 2-3/16 – 2 TWR2-055050 55-46 2-3/16 – 1-13/16 TWR2-055046 55-41 2-3/16 – 1-5/8 TWR2-055041

TWL2-060 60 2-3/8 60-55 2-3/8 – 2-3/16 TWR2-060055 60-50 2-3/8 – 2 TWR2-060050 60-46 2-3/8 – 1-13/16 TWR2-060046

TWLC4

TWL4-041 41 1-5/8 41-36 1-5/8 – 1-7/16 TWR4-041036 41-32 1-5/8 – 1-1/4 TWR4-041032 – – –

TWL4-046 46 1-13/16 46-41 1-13/16 – 1-5/8 TWR4-046041 46-36 1-13/16 – 1-7/16 TWR4-046036 46-32 1-13/16 – 1-1/4 TWR4-046032

TWL4-050 50 2 50-46 2 – 1- 13/16 TWR4-050046 50-41 2 – 1-5/8 TWR4-050041 50-36 2 – 1-7/16 TWR4-050036

TWL4-055 55 2-3/16 55-50 2-3/16 – 2 TWR4-055050 55-46 2-3/16 – 1-13/16 TWR4-055046 55-41 2-3/16 – 1-5/8 TWR4-055041

TWL4-060 60 2-3/8 60-55 2-3/8 – 2-3/16 TWR4-060055 60-50 2-3/8 – 2 TWR4-060050 60-46 2-3/8 – 1-13/16 TWR4-060046

TWL4-065 65 2-9/16 65-60 2-9/16 – 2-3/8 TWR4-065060 65-55 2-9/16 – 2-3/16 TWR4-065055 65-50 2-9/16 – 2 TWR4-065050

TWL4-070 70 2-3/4 70-65 2-3/4 – 2-9/16 TWR4-070065 70-60 2-3/4 – 2-3/8 TWR4-070060 70-55 2-3/4 – 2-3/16 TWR4-070055

TWL4-075 75 2-15/16 75-70 2-15/16 – 2-3/4 TWR4-075070 75-65 2-15/16 – 2-9/16 TWR4-075065 75-60 2-15/16 – 2-3/8 TWR4-075060

TWL4-080 80 3-1/8 80-75 3-1/8 – 2-15/16 TWR4-080075 80-70 3-1/8 – 2-3/4 TWR4-080070 80-65 3-1/8 – 2-9/16 TWR4-080065

TWLC8

TWL8-060 60 2-3/8 60-55 2-3/8 – 2-3/16 TWR8-060055 60-50 2-3/8 – 2 TWR8-060050 60-46 2-3/8 – 1-13/16 TWR8-060046

TWL8-065 65 2-9/16 65-60 2-9/16 – 2-3/8 TWR8-065060 65-55 2-9/16 – 2-3/16 TWR8-065055 65-50 2-9/16 – 2 TWR8-065050

TWL8-070 70 2-3/4 70-65 2-3/4 – 2-9/16 TWR8-070065 70-60 2-3/4 – 2-3/8 TWR8-070060 70-55 2-3/4 – 2-3/16 TWR8-070055

TWL8-075 75 2-15/16 75-70 2-15/16 – 2-3/4 TWR8-075070 75-65 2-15/16 – 2-9/16 TWR8-075065 75-60 2-15/16 – 2-3/8 TWR8-075060

TWL8-080 80 3-1/8 80-75 3-1/8 – 2-15/16 TWR8-080075 80-70 3-1/8 – 2-3/4 TWR8-080070 80-65 3-1/8 – 2-9/16 TWR8-080065

TWL8-085 85 3-3/8 85-80 3-3/8 – 3-1/8 TWR8-085080 85-65 3-3/8 – 2-15/16 TWR8-085065 85-70 3-3/8 – 2-3/4 TWR8-085070

TWL8-090 90 3-1/2 90-85 3-1/2 – 3-3/8 TWR8-090085 90-80 3-1/2 – 3-1/8 TWR8-090080 90-75 3-1/2 – 2-15/16 TWR8-090075

TWL8-095 95 3-3/4 95-90 3-3/4 – 3-1/2 TWR8-095090 95-85 3-3/4 – 3-3/8 TWR8-095085 95-80 3-3/4 – 3-1/8 TWR8-095080

TWL8-100 100 3-7/8 100-95 3-7/8 – 3-3/4 TWR8-100095 100-90 3-7/8 – 3-1/2 TWR8-100090 100-85 3-7/8 – 3-3/8 TWR8-100085



Body Reference Nut A/F Reducer Reducer Reducer

Order No. Link No. mm in mm in Order No. mm in Order No. mm in Order No.

TWLC15

TWL15-070 70 2-3/4 70–65 2-3/4 – 2-9/16 TWR15-070065 70-60 2-3/4 – 2-3/8 TWR15-070060 70-55 2-3/4 – 2-3/16 TWR15-070055

TWL15-075 75 2-15/16 75-70 2-15/16 – 2-3/4 TWR15-075070 75-65 2-15/16 – 2-9/16 TWR15-075065 75-60 2-15/16 – 2-3/8 TWR15-075060

TWL15-080 80 3-1/8 80-75 3-1/8 – 2-15/16 TWR15-080075 80-70 3-1/8 – 2-3/4 TWR15-080070 80-65 3-1/8 – 2-9/16 TWR15-080065

TWL15-085 85 3-3/8 85-80 3-3/8 – 3-1/8 TWR15-085080 85-65 3-3/8 – 2-15/16 TWR15-085065 85-70 3-3/8 – 2-3/4 TWR15-085070

TWL15-090 90 3-1/2 90-85 3-1/2 – 3-3/8 TWR15-090085 90-80 3-1/2 – 3-1/8 TWR15-090080 90-75 3-1/2 – 2-15/16 TWR15-090075

TWL15-095 95 3-3/4 95-90 3-3/4 – 3-1/2 TWR15-095090 95-85 3-3/4 – 3-3/8 TWR15-095085 95-80 3-3/4 – 3-1/8 TWR15-095080

TWL15-100 100 3-7/8 100-95 3-7/8 – 3-3/4 TWR15-100095 100-90 3-7/8 – 3-1/2 TWR15-100090 100-85 3-7/8 – 3-3/8 TWR15-100085

TWL15-105 105 – 105-100 – TWR15-105100 105-95 – TWR15-105095 105-90 – TWR15-105090

TWL15-425 – 4-1/4 – 4-1/4 – 3-7/8 TWR15-425388 – 4-1/4 – 3-3/4 TWR15-425375 – 4-1/4 – 3-1/2 TWR15-425350

TWL15-110 110 – 110-105 – TWR15-110105 110-100 – TWR15-110010 110-95 – TWR15-110095

TWL15-115 115 – 115-110 – TWR15-115110 115-105 – TWR15-115105 115-100 – TWR15-115100

TWL15-463 – 4-5/8 – 4-5/8 – 4-1/4 TWR15-463425 – 4-5/8 – 3-7/8 TWR15-463388 – 4-5/8 – 3-3/4 TWR15-463375

TWLC30

TWL30-080 80 3-1/8 80-75 3-1/8 – 2-15/16 TWR30-080075 80-70 3-1/8 – 2-3/4 TWR30-080070 80-65 3-1/8 – 2-9/16 TWR30-080065

TWL30-085 85 3-3/8 85-80 3-3/8 – 3-1/8 TWR30-085080 85-65 3-3/8 – 2-15/16 TWR30-085065 85-70 3-3/8 – 2-3/4 TWR30-085070

TWL30-090 90 3-1/2 90-85 3-1/2 – 3-3/8 TWR30-090085 90-80 3-1/2 – 3-1/8 TWR30-090080 90-75 3-1/2 – 2-15/16 TWR30-090075

TWL30-095 95 3-3/4 95-90 3-3/4 – 3-1/2 TWR30-095090 95-85 3-3/4 – 3-3/8 TWR30-095085 95-80 3-3/4 – 3-1/8 TWR30-095080

TWL30-100 100 3-7/8 100-95 3-7/8 – 3-3/4 TWR30-100095 100-90 3-7/8 – 3-1/2 TWR30-100090 100-85 3-7/8 – 3-3/8 TWR30-100085TWL30-105 105 – 105-100 – TWR30-105100 105-95 – TWR30-105095 105-90 – TWR30-105090TWL30-425 – 4-1/4 – 4-1/4 – 3-7/8 TWR30-425388 – 4-1/4 – 3-3/4 TWR30-425375 – 4-1/4 – 3-1/2 TWR30-425350TWL30-110 110 – 110-105 – TWR30-110105 110-100 – TWR30-110010 110-95 – TWR30-110095TWL30-115 115 – 115-110 – TWR30-115110 115-105 – TWR30-115015 115-100 – TWR30-115100TWL30-463 – 4-5/8 – 4-5/8 – 4-1/4 TWR30-463425 – 4-5/8 – 3-7/8 TWR30-463388 – 4-5/8 – 3-3/4 TWR30-463375TWL30-120 120 – 120-115 – TWR30-120115 120-110 – TWR30-120110 120-105 – TWR30-120105TWL30-500 – 5 – 5 – 4-5/8 TWR30-500463 – 5 – 4-1/4 TWR30-500425 – 5 – 3-7/8 TWR30-500388TWL30-130 130 – 130-120 – TWR30-130120 130-115 – TWR30-130115 130-110 – TWR30-130110TWL30-135 135 5-3/8 135-125 5-3/8 – 5 TWR30-135125 135-120 5-3/8 – 4-5/8 TWR30-135120 135-115 5-3/8 – 4-1/4 TWR30-135115TWL30-145 145 5-3/4

AVAILABLE UPON REQUESTTWL30-150 150 –TWL30-155 155 6-1/8




30

TORQUE WRENCH

REACTION ARMS - TWLC

SPX FLOW Bolting Systems offer a varied range of alternative and optional reaction accessories, which help to find a reaction point solution no matter how unusual the bolted application is.

TWLC REACTION BAR TWLC-RB

• In-Line Extension Reaction Bar for TWLC wrench: allows extended reach on the same plane

• Pin engagement, no tools required• Available for full range of tool sizes

TWLC REACTION PADDLETWLC-RP

• Off-Set Reaction Arm for TWLC wrench: allows off-set reaction within wrench profile

• Pin engagement, no tools required • Light alloy construction• Available for full range of tool


L1

L2L3

Tool Ref Order No.L1 L2 L3 Weight

mm in mm in mm in kg lb TWLC2 TWLC2-RB 381 15 28 1.10 55 2.17 2.6 5.7TWLC4 TWLC4-RB 457 18 35 1.38 66 2.60 4.8 10.6TWLC8 TWLC8-RB 457 18 37 1.46 85 3.35 9 19.8TWLC15 TWLC15-RB 508 20 40 1.57 102 4.01 14.5 32TWLC30 TWLC30-RB 508 20 35 1.38 127 5 27 59.5


L4L3 L2

L1


mm in mm in mm in mm in kg lbTWLC2 TWLC2-RP 84 3.31 35 1.38 142 5.59 13 0.51 0.5 1.1TWLC4 TWLC4-RP 109 4.29 46 1.81 178 7.01 19 0.75 0.9 2TWLC8 TWLC8-RP 136,5 5.37 57 2.25 220 8.66 26 1.02 1.8 4TWLC15 TWLC15-RP 165 6.50 70 2.76 252 9.92 45 1.77 3.5 7.7TWLC30 TWLC30-RP 200 7.874 86 3.39 317 12.48 44 1.73 6 13.2


CUSTOM REACTION PADS AND REDUCERS ARE AVAILABLE. Contact SPX FLOW or an authorized distributor for more details

WHEN NOTHING ELSE WILL WORK, SPLIT ADAPTERS ARE MADE TO ORDER AND AVAILABLE UPON REQUEST.

HAVE A UNIQUE APPLICATION? DOES STANDARD PRODUCT NOT FIT?

TWLC15 split adapter, closed position

TWLC15 split adapter, open position

32

Drive Body

TWSL Series

TWLC Series

Optional Handle Order #: DFTAS000002

TORQUE WRENCH

SLIMLINE, TWSL

THE SLIMLINE

TORQUE WRENCHThe SlimLine Torque Wrench is engineered to fit inaccessible applications with minimal clearance.

Features & Benefits• Dynamic engineering modeling (FEA) optimized tool

design to extend life and durability• The SlimLine links use the same quick change Drive

Body as the existing TWLC links• Small nose radius, fits all standard API and ANSI

flanges• Rigid steel body construction with corrosion resistant

plating• Fully enclosed drive mechanism for operator safety• Swivel manifold has an internal relief valve to prevent

retract side over-pressurization• Multi-axis swivel technology for free positioning of tool

and hoses

The Drive Body is designed to interchange with the TWLC (Low Clearance) and the new TWSL (SlimLine) Links, lowering your tool investment across each series to broaden your application reach.

DRIVE BODY INTERCHANGES WITH THE TWLC & TWSL LINK SIZES

*Contact your nearest SPXFLOW Bolting Systems sales representative for assistance in sizing the proper tool for your application, or go to spxboltingsystems.com website for details about other available link sizes not listed.

SizeA B C D E F G

mm (In)

mm (In)

mm (In)

mm (In)

mm (In)

mm (In)

mm (In)

TWSL2 145 (5.71)

114 (4.49)

128 (5.04)

184.5 (7.26)

8.8 (0.35)

25.0 (0.98)

42.00 (1.65)

TWSL4 168.1 (6.61)

137.0 (5.39)

168.0 (6.61)

224.3 (8.83)

10.72 (0.42)

30.5 (1.20)

52.00 (2.04)

*TWSL4-046 DIMENSION 9.91mm

SIZE HEX RANGE A(mm)

B(mm)

C (mm)

D(mm)

E(mm)

F(mm)

G(mm)

MIN TORQUElb-ft (Nm)

MAX TORQUElb-ft (Nm)

TWSL4 1 11/16" - 3 1/8" 43 - 80 mm 168.1 137.0 168.0 224.3 10.72* 30.5 52.0 505 (685) 2639 - 4210 (3578 - 5708)

D

A

HEX RANGE

E

C

B

F

GG

FFC

FAFB

FE

FD

HEX RANGE


Drive BodyOrder No.

Hex Range for SlimLine SlimLine Min Torque SlimLine Max. Torque Weight (Body Only)


TWLC2 28 60 1-1/8 2-3/8 301 222 1,681 ~ 2,508 1,240 ~ 1,850 1.0 2.2TWLC4 46 80 1-13/16 3-1/8 685 505 3,578 ~ 5,708* 2,639 ~ 4,210* 2.0 4.4TWLC8 57 100 2-1/4 3-15/16 Contact Factory for Details 3.5 7.7

Note: Links are sold separately from the drive body, refer to the tables below.

Torque Wrench Drive Body Ordering Information for SlimLine


The TWSL’s narrow width and reduced radius design enables the tool to fit into tight areas where standard low clearance links cannot.

Due to the compact design, the maximum torque of the TWSL links vary depending on link size, * reference the information below for complete details.

TWSL2 SlimLine Link Reference Table*

Nut A/F Link

Order No.

Max. Torque Weight(Link Only)

mm in Nm lb-ft kg lb32 1-1/4 TWSL2-032 1,681 1,240 1.87 4.1

36 1-7/16 TWSL2-036 1,939 1,430 1.90 4.2

41 1-5/8 TWSL2-041 2,169 1,600 1.93 4.3

46 1-13/16 TWSL2-046 2,508 1,850 1.95 4.3

50 2 TWSL2-050 2,508 1,850 1.96 4.3

55 2-3/16 TWSL2-055 2,508 1,850 1.98 4.4

60 2-3/8 TWSL2-060 2,508 1,850 1.99 4.4

* Shown with optional handle, order # DFTAS000001 for TWSL2, DFTAS00002 for TWSL4 & TWSL8.

Torque Wrench Link Ordering Information for SlimLine

Link Order No.

Hex Range for SlimLine SlimLine Min Torque SlimLine Max. Torque Weight (Link Only)


TWSL2-# 28 60 1-1/8 2-3/8 301 222 1,681 - 2,508 1,240 - 1,850 1.9 - 2.05 4.2 - 4.5TWSL4-# 46 80 1-13/16 3-1/8 685 505 3,578 ~ 5,708* 2,639 ~ 4,210* 3.7 - 3.8 8.0 - 8.4TWSL8-# 57 100 2-1/4 3-15/16 Contact Factory for Details

Note: The “#” suffix will be replaced with the actual link size in a numeric value.

SlimLine Application Range

Standard

(TWLC Series)

New SlimLine*

(TWSL Series)

TWSL4 SlimLine Link Reference Table*

Nut A/F Link

Order No.

Max. Torque Weight(Link Only)

mm in Nm lb-ft kg lb

46 1-13/16 TWSL4-046 3,578 2,639 3.65 8

50 2 TWSL4-050 4,435 3,271 3.72 8.2

55 2-3/16 TWSL4-055 4,838 3,568 3.74 8.2

60 2-3/8 TWSL4-060 5,243 3,867 3.78 8.3

65 2-9/16 TWSL4-065 5,708 4,210 3.79 8.4

70 2-3/4 TWSL4-070 5,708 4,210 3.81 8.4

75 2-15/16 TWSL4-075 5,708 4,210 3.83 8.4

80 3-1/8 TWSL4-080 5,708 4,210 3.82 8.4

Bolting Catalog 2019 - SPX Flow · TORQUE WRENCHES MEASUREMENTS/ SPECIFICATIONS Torque Wrench...

Documents

Transcript of Bolting Catalog 2019 - SPX Flow · TORQUE WRENCHES MEASUREMENTS/ SPECIFICATIONS Torque Wrench...