BNC2010 - 住友電工ハードメタル › downloads › assets › mt... ·...
Transcript of BNC2010 - 住友電工ハードメタル › downloads › assets › mt... ·...
スミボロン製品ガイドNo.043
● 高能率加工用チップもラインナップ● チップブレーカ付きワンユースチップ ブレイクマスター 軽切削用 FV型 / 仕上げ切削用 LV型 シリーズ化
● 高能率加工用チップもラインナップ● チップブレーカ付きワンユースチップ ブレイクマスター 軽切削用 FV型 / 仕上げ切削用 LV型 シリーズ化
Stable, Long Tool LifeTrump Card for Cost Reduction
・Inserts for High-ef�ciency Machining Also Available・One-use Insert Break Master with Chipbreaker FV Type for Light Cutting/LV Type for Finishing Added to Series
Long Tool Life
安定・長寿命コスト低減の切り札安定・長寿命コスト低減の切り札
BNC2010 BNC2020
高精度 汎用・高能率GENERAL PURPOSE/HIGH EFFICIENCYHIGH PRECISION
COATED SUMIBORON COATED SUMIBORON
● ●高能率加高能率加●●チップブチップブ
BNC201
高精HIHIHIGHGHGHG PPPRERERE
COATED SUMIBOROCOATED SUMIBORO
プもラインナッププもラインナップレーカ付きワンユースチップレーカ付きワンユースチップ
Stable,Trump Stable
C2020
用・高能率率率UUUURPRPRPOSOSOSOSE/E/E//HIHIHIGHGHGHG EEEFFFFFFICICICCIEIEIENCNCNCCYYYYYYY
SUMIBORONSUMIBORONSUMIBORON
加工用チップ加工用チップレーカ付きレーカ付き
BNC
汎用GEGEGEGENENENERARARALLL PPP
COATEDCOATEDCOATED10
精度度度EEECICICIC SISISIS ONONONONNN
ONON
焼入鋼加工用コーテッドCBN焼結体Coated SUMIBORON for Hardened Steel Machining
コーテッドスミボロン BNC2010/BNC2020Coated SUMIBORON BNC2010 / BNC2020 第3版
hyou1.indd 1 2015/04/21 17:41
BNC2010 ・面粗度、寸法精度が要求される仕上げ加工に対応した高精度加工用材種・新開発のCBN母材にTiCN膜をコーティングし、更に耐摩耗性を向上・新開発の特殊多層膜により境界摩耗を抑制し、優れた面粗度を安定して実現
BNC2020 ・焼入鋼全般の加工に対応した汎用材種・新開発の強靭なCBN母材に耐摩耗性に優れるTiAlN膜をコーティング・強密着層による膜剥離抑制により更なる安定加工、長寿命化を実現
・ A grade for high-precision machining applicable to finishing requiring good surface roughness and dimensional accuracy・ Provides further improved wear resistance thanks to a newly developed CBN substrate coated with a TiCN layer・ Reduces boundary wear and stably achieves excellent surface finish thanks to newly developed special multi-layered coating
・ A general-purpose grade applicable to general hardened steel machining・ A newly developed tough CBN substrate coated with a highly wear-resistant TiAlN layer・ Achieves more stable machining and longer tool life by employing a highly adhesive layer to reduce delamination
更なる長寿命化コスト低減の切り札
コーテッドスミボロン
高精度
汎用・高能率GENERAL PURPOSE
HIGH EFFICIENCY
HIGH PRECISION
COATED SUMIBORON
COATED SUMIBORON
コーテッドスミボロン
Longer Tool LifeTrump Card for Cost Reduction
■ BNC2010 と BNC2020 の CBN 母材とコーティング構造 CBN Substrate and Coating Structure of BNC2010 and BNC2020
■ 適用範囲 Application Range ■ 推奨切削条件 Recommended Cutting Conditions
BNC2010
TiCN膜と特殊多層膜の積層構造により優れた耐境界摩耗性を実現Achieves excellent boundary wear resistance thanks to a laminated structure of a TiCN layer and special multi-layered coating
TiAlN 膜と強密着層により更なる安定性を実現Achieves further stability thanks to TiAlN and highly adhesive coating layers
BNC2020
BNC2010 BNC2020120 250150 200 300
切削速度 Cutting Speed vc(m/min)
送り量 Feed Rate f(mm/rev)
切込み Depth of Cut ap(mm)
0.03 ~ 0.25 0.03 ~ 0.35
50 200100 150 220切削速度 Cutting Speed vc(m/min)
送り量 Feed Rate f(mm/rev)
切込み Depth of Cut ap(mm)
0.03 ~ 0.40 0.03 ~ 0.50
120 250150 200 300切削速度 Cutting Speed vc(m/min)
送り量 Feed Rate f(mm/rev)
切込み Depth of Cut ap(mm)
0.03 ~ 0.25 0.03 ~ 0.35
50 200100 150 220切削速度 Cutting Speed vc(m/min)
送り量 Feed Rate f(mm/rev)
切込み Depth of Cut ap(mm)
0.03 ~ 0.40 0.03 ~ 0.50
弱断続Light Interrupted
中断続Midium Interrupted
強断続Heavy Interrupted
連続Continuous
刃先への負荷 大小Small LargeImpact Force on Cutting Edge
300
200
120100
断続の強さ
切削速度vC
(m/min)
BNC100
BNC2010 BNC160
BNC2020
BNC300
BNC200
Cut
ting
Spe
edIn
terr
uptio
n Fr
eque
ncy
TiCN膜TiCN Layer
TiN膜 TiN Layer
特殊多層膜Special Multi-layered Coating
TiCN膜TiCN Layer
特殊多層膜Special Multi-layered Coating
TiCN膜TiCN Layer
特殊多層膜Special Multi-layered Coating
耐摩耗性向上Improved Wear Resistance
高耐摩耗性CBN母材
Highly Wear-Resistant CBN Substrate
境界摩耗抑制Reduced Boundary Wear
TiN膜 TiN Layer
TiAlN層TiAlN Layer
強密着層Highly Adhesive Layer
強靱なCBN母材
Tough CBN Substrate
密着力向上Improved Adhesion
耐摩耗性向上Improved Wear Resistance
2 3
002-003.indd 2 2015/04/21 9:34
BNC2010 ・面粗度、寸法精度が要求される仕上げ加工に対応した高精度加工用材種・新開発のCBN母材にTiCN膜をコーティングし、更に耐摩耗性を向上・新開発の特殊多層膜により境界摩耗を抑制し、優れた面粗度を安定して実現
BNC2020 ・焼入鋼全般の加工に対応した汎用材種・新開発の強靭なCBN母材に耐摩耗性に優れるTiAlN膜をコーティング・強密着層による膜剥離抑制により更なる安定加工、長寿命化を実現
・ A grade for high-precision machining applicable to finishing requiring good surface roughness and dimensional accuracy・ Provides further improved wear resistance thanks to a newly developed CBN substrate coated with a TiCN layer・ Reduces boundary wear and stably achieves excellent surface finish thanks to newly developed special multi-layered coating
・ A general-purpose grade applicable to general hardened steel machining・ A newly developed tough CBN substrate coated with a highly wear-resistant TiAlN layer・ Achieves more stable machining and longer tool life by employing a highly adhesive layer to reduce delamination
更なる長寿命化コスト低減の切り札
コーテッドスミボロン
高精度
汎用・高能率GENERAL PURPOSE
HIGH EFFICIENCY
HIGH PRECISION
COATED SUMIBORON
COATED SUMIBORON
コーテッドスミボロン
Longer Tool LifeTrump Card for Cost Reduction
Negative Land Angle
Negative LandCutting Edge
Negative Land Honing
Negative Land Width Negative Land Angle
Edge Treatment Identification Code
Negative Land Width
BNC2010
BNC2020
S01225 あり25° 0.12
S01225 あり25° 0.12
S01730 あり30° 0.17
S02735 あり35° 0.27
●刃先仕様記号の呼び方
刃先形状
ネガランド幅W ネガランド角α
ネガランド幅W
ネガランド角α°Rホーニング
T:ネガランドS:ネガランド+Rホーニング
S 0 1 2 2 5
刃先仕様記号 W ホーニングα 刃先仕様記号 W ホーニングα
汎用タイプ:標準型材種
刃先強化タイプ:HS型
Honing
General Purpose : Standard
Edge Treatment
Grades
Honing Edge Treatment Honing
Yes Yes
Yes Yes
Strong Edge Type : HS
ConventionalCoated CBN
Tool Life 2.3x
Cut
ting
Leng
th
Surface Roughness
100
50
0
BN2010 従来コーテッドCBN
加工数
(個)
寿命 2.3倍
面粗度 Ra=0.6μm
切削距離5.7㎞
WH TypeWiper Inserts
ConventionalCoated CBN
Tool Life 1.8x
Cut
ting
Leng
th
Surface Roughness
加工数
(個)
700
300
500
0BN2010WH型ワイパーチップ
従来コーテッドCBN
寿命 1.8倍
面粗度 Rz=1.6μm
切削距離4㎞
Tool Life 1.5x
ConventionalCoated CBN
加工数
(個)
300
200
100
0
BN2020 従来コーテッドCBN
寿命 1.5倍
Strong Edge TypeHS Type
ConventionalCoated CBN
Tool Life 1.5x
加工数
(個)
HS型刃先強化タイプ
100
200
300
0BN2020 従来コーテッド
CBN
寿命 1.5倍
■ 刃先処理仕様 Cutting Edge Treatment
■ 切削性能 Cutting Performance
■ 使用実例 Application Example
Coated SUMIBORON BNC2010 / BNC2020
Conventional Coated CBNBoundary wear occurs
Reduces boundary wear
Cutting Distance
BNC2010
7
6
5
4
3
2
1
BNC2010
従来コーテッドCBN
切削距離(km)
面粗さRz (μm)
●
●●
■
■
■
■
従来コーテッドCBN境界摩耗発生
BNC2010境界摩耗を抑制
8km加工後
8km加工後
●
0 2 4 6 8
After Cutting 8km
After Cutting 8km
Conventional Coated CBN
Sur
face
Rou
ghne
ss
Tool Life
BNC2020
BNC2020
従来コーテッドCBN
他社コーテッドCBN
5.0工具寿命(km)
0 2.5
2.5km加工後
3km加工後
5km加工後
1.8倍寿命向上
After Cutting 5km
1.8 Times the Conventional Tool Life
After Cutting 3km
After Cutting 2.5km
ConventionalCoated CBN
Comp.Coated CBN
メインシャフト外径連続加工 (58~60HRC)Continuous External Turning of Main Shaft
CVJアウターレース端面加工 (58~60HRC)Facing of CVJ Outer Race
サンギア浸炭層除去加工 (58~60HRC)Carburized Layer Removal for Sun Gears
CVJケージ窓断続加工 (58~60HRC)Interrupted Machining of CVJ Cage Window
BNC2010は耐摩耗性に優れ、良好な面粗度を実現BNC2010 provides excellent wear resistance and achieves excellent surface roughness.
BNC2010+ワイパーチップWH型は、優れた面粗度を長時間維持BNC2010 with a WH type wiper insert maintains excellent surface finish for a long time.
BNC2020は高負荷切削で長寿命を達成BNC2020 achieves a long tool life in high load cutting.
BNC2020の刃先強化タイプHS型は、断続切削で安定性能を発揮BNC2020 strong edge HS type provides stable performance in interrupted cutting.
BNC2010
BNC2010
BNC2020
BNC2020
チップ:2NC-CNGA120412WH (BNC2010)Inserts
切削条件:vc=150m/min f=0.2mm/rev ap=0.2mm DryCutting Conditions
チップ:4NC-DNGA150408 (BNC2010)Inserts
切削条件:vc=200m/min f=0.10mm/rev ap=0.35mm DryCutting Conditions
被削材:SCM415 58-62HRC (連続)Work Material Continuous
チップ:4NC-DNGA150408 刃先処理:S01225Inserts Cutting Edge Treatment
切削条件:vc=160m/min f=0.08mm/rev ap=0.1mm WetCutting Conditions
被削材:SCM415-5V 58-62HRC (断続切削)Work Material Interrupted
チップ:4NC-CNGA120412 刃先処理:S01225Inserts Cutting Edge Treatment
切削条件:vc=130m/min f=0.1mm/rev ap=0.6mm DryCutting Conditions
チップ:4NC-CNGA120408 (BNC2020)Inserts
切削条件:vc=100m/min f=0.15mm/rev ap=0.5mm WetCutting Conditions
チップ:3NC-TNGA160420HS (BNC2020)Inserts
切削条件:vc=120m/min f=0.10mm/rev ap=0.15mm DryCutting Conditions
2 3
002-003.indd 3 2015/04/21 9:34
4 5
Negative Land Angle
Negative LandCutting Edge
Negative Land Honing
Negative Land Width Negative Land Angle
Edge Treatment Identification Code
Negative Land Width
BNC2010
BNC2020
S01215 あり15° 0.12
S01215 あり15° 0.12
S01215 あり15° 0.12
S01215 あり15° 0.12
●刃先仕様記号の呼び方
刃先形状
ネガランド幅W ネガランド角α
ネガランド幅W
ネガランド角α°Rホーニング
T:ネガランドS:ネガランド+Rホーニング
S 0 1 2 2 5
刃先仕様記号 W ホーニングα 刃先仕様記号 W ホーニングα
ワイパーチップ WG型材種
ワイパーチップ WH型
Honing
Wiper Insert : WG Type
Edge Treatment
Grades
Honing Edge Treatment Honing
Yes Yes
Yes Yes
Wiper Insert : WH Type
■ 刃先処理仕様 Cutting Edge Treatment
■ 刃先処理仕様 Cutting Edge Treatment
■ ワンユースワイパーチップ WG 型 /WH 型 SUMIBORON One-Use Wiper inserts WG Type / WH Type
● 適用領域(面粗さ規格1.6s~3.2s) Application Range (Surface Roughness Standard: 1.6s to 3.2s)
● ワイパーチップの作用 Purpose of Wiper Edge
● ワイパーチップの仕上げ面粗さ Surface Roughness of Wiper Insert
■ チップブレーカ付きワンユースチップ ブレイクマスター FV 型 /LV 型 /SV 型 SUMIBORON Break Master FV Type / LV Type / SV Type
● 適用範囲 Application Range
Coated SUMIBORON BNC2010 / BNC2020
・焼入鋼加工の切りくず処理に最適なチップブレーカ・FV型 /LV型は焼入鋼仕上げ~軽切削に最適・SV型は浸炭層除去加工に最適で、独自設計のブレーカ形状により、 焼入部から未焼入部まで切りくず処理が可能
・焼入鋼加工用ワイパーチップで研削加工に匹敵する優れた面粗さを実現・低送り加工用WG型、高送り加工用WH型をラインアップ
・A chipbreaker ideal for chip control in hardened steel machining.・FV Type and LV Type are ideal for finishing and light cutting of hardened steel.・SV Type is ideal for carburized layer removal and is applicable to both hardened and
non-hardened parts with effective chip control thanks to its unique chipbreaker design.
・ By using wiper inserts for hardened steel machining, achieves excellent surface roughness on the same level achieved with grinding.・ WG Type for low-feed machining and WH Type for high-feed machining are available.
・To optimize the effectiveness, we recommend using wiper inserts for continuous cutting.・Chattering and undulation may occur, so use with high-rigidity machines and work materials.
Dep
th o
f Cut
SV型SV型
0.1 0.2 0.30
0.1
0.3
0.5
0.7
LV型LV型
送り量 f Feed Rate (mm/rev)
切込み
FV型FV型
ap(mm)
FV Type
LV Type
SV Type LV型 軽切削用切込み 0.3mm以下の条件で優れた切りくず処理性を発揮
FV型 仕上げ切削用切込み 0.2mm以下の仕上げ条件で優れた切りくず処理性を発揮
SV型 浸炭層除去加工用浸炭焼入層除去加工に最適。チョコ停や寸法不良を解消
Delivers outstanding chip control in conditions with a depth of cut of 0.3 mm or less.
Delivers outstanding chip control in finishing conditions with a depth of cut of 0.2 mm or less.
Perfect for carburised layer removal.No constant stoppage or incorrect part dimension problems.
0.050.60
-35°
30°
45°0.4
0.15
-35°30°
0.84
SV Typefor Carburised Layer Removal
LV Typefor Lightcutting
FV Typefor Finishing Cut
SV Type
FV Type
LV Type
材種Grades
Negative Land Angle
Negative LandCutting Edge
Negative Land Honing
Negative Land Width Negative Land Angle
Edge Treatment Identification Code
Negative Land Width
BNC2010
BNC2020
ー あり0° 0.12
ー あり0° 0.12
●刃先仕様記号の呼び方
刃先形状
ネガランド幅W ネガランド角α
ネガランド幅W
ネガランド角α°Rホーニング
T:ネガランドS:ネガランド+Rホーニング
S 0 1 2 2 5
刃先仕様記号 W ホーニングα
ブレイクマスター FV型
Honing
Break Master FV Type
Edge Treatment Honing
Yes
Yes
S00535 あり35° 0.05
S00535 あり35° 0.05
刃先仕様記号 W ホーニングα
ブレイクマスター LV型Break Master LV Type
Edge Treatment Honing
Yes
Yes
S01235 あり35° 0.12
S01235 あり35° 0.12
刃先仕様記号 W ホーニングα
ブレイクマスター SV型Break Master SV Type
Edge Treatment Honing
Yes
Yes
Cut
ting
Spe
ed
0.1 0.30.2
150
WG型 WH型
WG型 WH型
WG型 WH型
0.40.05
220
100
50BN2000
BNC2010
BNC2020
切削速度vC
(m/min)
送り量 f Feed Rate (mm/rev)
WG Type
WG Type
WG Type
WH Type
WH Type
WH Type
・ ワイパー切れ刃の効果を最大限に発揮するため、連続切削での使用を推奨します。・ うねりやびびりが発生する可能性がありますので、剛性の高い機械と被削材で使用してください。
ワイパーチップ 標準チップ(ワイパー無し ノーズR0.8)Wiper Insert Standard Insert (No Wiper / R0.8)
f:送り量
Rz(最大高さ)送り方向
ワイパー刃
チップ
被削材
f:送り量
Rz(最大高さ)送り方向
チップ
Feed DirectionHighest peak Highest peak
Feed Direction
Feed Rate Feed Rate
Insert Insert
Wiper Insert
ワイパーチップ(WG型/WH型) 標準チップ(ワイパー無し ノーズR0.8)
低送り加工(f =0.1mm) 高送り加工(f =0.3mm) 低送り加工(f =0.1mm) 高送り加工(f =0.3mm)
面粗さ
面粗さRz
Surface Roughness Rz(Highest peak)
Surface RoughnessProfile
Low feed cutting High feed cutting
WG Type WH Type
Low feed cutting High feed cutting
(最大高さ)
WG型 WH型
Wiper Insert (WG Type/WH Type) Standard Insert (No Wiper / R0.8)
004-005.indd 4 2015/04/21 9:35
4 5
Coated SUMIBORON BNC2010 / BNC2020
BNC2010/BNC2020 在庫型番(ネガティブ)■マルチコーナーワンユースチップ/ネガティブ(穴つき)
Multi-cornered,One-use Type/Negative(With Hole)
外 観Appearance
型 番Catalogue No.
在庫 Stock
コ
ナ
数No ofCutting Edges
焼結体切刃長Cutting Edge Length
寸法 Dimensions(mm)
BNC2
010
BNC2
020
内接円Inscribed Circle
厚 さThickness
穴 径Hole
ノーズ半径
Nose Radius
2NC-CNGA120404 D D2
2.512.7 4.76 5.16
0.4120408 D D 2.4 0.8120412 D D 2.3 1.2
4NC-CNGA120404 D D4
2.512.7 4.76 5.16
0.4120408 D D 2.4 0.8120412 D D 2.3 1.2
4NC-CNGA120404WG D D4
2.412.7 4.76 5.16
0.4120408WG D D 2.4 0.8120412WG D D 2.3 1.2
4NC-CNGA120404WH D D4
2.412.7 4.76 5.16
0.4120408WH D D 2.3 0.8120412WH D D 2.2 1.2
2NC-DNGA150404 D D2
2.512.7 4.76 5.16
0.4150408 D D 2.1 0.8150412 D D 2.0 1.2
4NC-DNGA150404 D D4
2.512.7 4.76 5.16
0.4150408 D D 2.1 0.8150412 D D 2.0 1.2
4NC-DNGA150404WG D D 42.3
12.7 4.76 5.160.4
150408WG D D 2.0 0.8
4NC-DNGA150404WH D D 42.1
12.7 4.76 5.160.4
150408WH D D 1.8 0.8
4NC-SNGA120404 D D4
2.512.7 4.76 5.16
0.4120408 D D 2.3 0.8120412 D D 2.1 1.2
3NC-TNGA160404 D D3
2.39.525 4.76 3.81
0.4160408 D D 2.0 0.8160412 D D 2.0 1.2
6NC-TNGA160404 D D6
2.39.525 4.76 3.81
0.4160408 D D 2.0 0.8160412 D D 2.0 1.2
2NC-VNGA160404 D D2
2.89.525 4.76 3.81
0.4160408 D D 2.0 0.8160412 1.7 1.2
4NC-VNGA160404 D D4
2.89.525 4.76 3.81
0.4160408 D D 2.0 0.8160412 D 1.7 1.2
6NC-WNGA0804046
2.312.7 4.76 5.16
0.4080408 D D 2.0 0.8080412 2.0 1.2
6NC-WNGA080408WH D D 6 1.9 12.7 4.76 5.16 0.8
6NC-WNGA080408WG D D 6 2.0 12.7 4.76 5.16 0.8
※型番末尾 WG:低送り用ワイパーチップ WH型:高送り用ワイパーチップWG : Wiper insert for Low-feed type WH : Wiper insert for High-feed type
■マルチコーナーワンユースチップ/ネガティブ(穴つき)Multi-cornered,One-use Type/Negative(With Hole)
外 観Appearance
型 番Catalogue No.
在庫 Stock
コ
ナ
数No ofCutting Edges
焼結体切刃長Cutting Edge Length
寸法 Dimensions(mm)
BNC2
010
BNC2
020
内接円Inscribed Circle
厚 さThickness
穴 径Hole
ノーズ半径
Nose Radius
2NC-CNGA120416 D D2
3.312.7 4.76 5.16
1.6120420 D D 3.2 2.0120424 D D 3.1 2.4
4NC-CNGA120416 D D4
3.312.7 4.76 5.16
1.6120420 D D 3.2 2.0120424 D D 3.1 2.4
2NC-DNGA150416 D D2
3.412.7 4.76 5.16
1.6150420 D D 3.0 2.0150424 D D 2.7 2.4
4NC-DNGA150416 D D4
3.412.7 4.76 5.16
1.6150420 D D 3.0 2.0150424 D D 2.7 2.4
3NC-TNGA160416 D D3
3.39.525 4.76 3.81
1.6160420 D D 3.0 2.0160424 D D 2.7 2.4
6NC-TNGA160416 D D6
3.39.525 4.76 3.81
1.6160420 D D 3.0 2.0160424 D D 2.7 2.4
※チップ逃げ面が干渉する為、専用ホルダをご使用ください。専用ホルダの詳細は総合カタログ[スミボロン章]をご覧ください。* The insert flank may cause interference, so use exclusive holders. For details on exclusive holders, refer to the chapter of SUMIBORON in the General Catalog.
■マルチコーナーワンユースチップ/ネガティブ(穴つき)Multi-cornered,One-use Type/Negative(With Hole)
外 観Appearance
型 番Catalogue No.
在庫 Stock
コ
ナ
数No ofCutting Edges
焼結体切刃長Cutting Edge Length
寸法 Dimensions(mm)
BNC2
010
BNC2
020
内接円Inscribed Circle
厚 さThickness
穴 径Hole
ノーズ半径
Nose Radius
4NC-CNGA120404HS D D4
2.512.7 4.76 5.16
0.4120408HS D D 2.4 0.8120412HS D D 2.3 1.2
4NC-DNGA150404HS D D4
2.512.7 4.76 5.16
0.4150408HS D D 2.1 0.8150412HS D D 2.0 1.2
6NC-TNGA160404HS D D6
2.39.525 4.76 3.81
0.4160408HS D D 2.0 0.8160412HS D D 2.0 1.2
4NC-VNGA160404HS D D4
2.89.525 4.76 3.81
0.4160408HS D D 2.0 0.8160412HS D 1.7 1.2
6NC-WNGA080408HS D D 6 2.0 12.7 4.76 5.16 0.8
■マルチコーナーワンユースチップ/ネガティブ(穴つき)Multi-cornered,One-use Type/Negative(With Hole)
外 観Appearance
型 番Catalogue No.
在庫 Stock
コ
ナ
数No ofCutting Edges
焼結体切刃長Cutting Edge Length
寸法 Dimensions(mm)
BNC2
010
BNC2
020
内接円Inscribed Circle
厚 さThickness
穴 径Hole
ノーズ半径
Nose Radius
4NC-CNGG120404N-FV D D4
2.512.7 4.76 5.16
0.4120408N-FV D D 2.4 0.8120412N-FV D D 2.3 1.2
4NC-CNGG120404N-LV D D4
2.512.7 4.76 5.16
0.4120408N-LV D D 2.4 0.8120412N-LV D D 2.3 1.2
4NC-CNGG120404N-SV4
2.512.7 4.76 5.16
0.4120408N-SV D 2.4 0.8120412N-SV D 2.4 1.2
4NC-DNGG150404N-FV D D4
2.512.7 4.76 5.16
0.4150408N-FV D D 2.1 0.8150412N-FV D D 2.0 1.2
4NC-DNGG150404N-LV D D4
2.512.7 4.76 5.16
0.4150408N-LV D D 2.1 0.8150412N-LV D D 2.0 1.2
4NC-DNGG150404N-SV4
2.512.7 4.76 5.16
0.4150408N-SV D D 2.1 0.8150412N-SV D D 2.0 1.2
6NC-TNGG160404N-FV D D6
2.39.525 4.76 3.81
0.4160408N-FV D D 2.0 0.8160412N-FV D D 2.0 1.2
6NC-TNGG160404N-LV D D6
2.39.525 4.76 3.81
0.4160408N-LV D D 2.0 0.8160412N-LV D D 2.0 1.2
6NC-TNGG160404N-SV6
2.39.525 4.76 3.81
0.4160408N-SV D D 2.0 0.8160412N-SV D D 2.0 1.2
4NC-VNGG160404N-FV D D 42.8
9.525 4.76 3.810.4
160408N-FV D D 2.0 0.8
4NC-VNGG160404N-LV D D 42.8
9.525 4.76 3.810.4
160408N-LV D D 2.0 0.8
※型番末尾 FV:仕上げ切削用 LV:軽切削用 SV:浸炭層除去加工用FV : Chipbreaker for Finish cutting type LV : Chipbreaker for Light cutting type SV : Carburised layer removal
高能率加工用High Efficiency Machining
刃先強化タイプ HS 型Strong Edge Type HS
ブレイクマスターBreak Master
ワイパー
ワイパー
ワイパー
ワイパー
ワイパー
ワイパー
D印:標準在庫品 無印:受注生産品DMark:Standard Stock Item No mark: Made-to-order item
004-005.indd 5 2015/04/21 9:35
� R2(2015.5)Ⅲ�1410�TP
BNC2010/BNC2020 在庫型番(ポジティブ)
Coated SUMIBORON BNC2010 / BNC2020
■マルチコーナーワンユースチップ/ボジティブ(穴つき)Multi-cornered,One-use Type/Positive(With Hole)
外 観Appearance
逃げ角ReliefAngle
型 番Catalogue No.
在庫�Stock
コ
ナ
数No ofCutting Edges
焼結体切刃長Cutting Edge Length
寸法�Dimensions(mm)
BNC2
010
BNC2
020
内接円Inscribed Circle
厚�さThickness
穴�径Hole
ノーズ半径
Nose Radius
7° 2NC-CCGW060202 D D 22.4
6.35 2.38 2.80.2
060204 D D 2.3 0.4
7°2NC-CCGW09T302 D D
22.5
9.525 3.97 4.40.2
09T304 D D 2.5 0.409T308 D D 2.4 0.8
7° 2NC-CCGW09T304WG D D 22.4
9.525 3.97 4.40.4
09T308WG D D 2.4 0.8
7° 2NC-CCGW09T304WH D D 22.4
9.525 3.97 4.40.4
09T308WH D D 2.3 0.8
7° 2NC-DCGW070202 D D 22.6
6.35 2.38 2.80.2
070204 D D 2.5 0.4
7°2NC-DCGW11T302 D D
22.7
9.525 3.97 4.40.2
11T304 D D 2.5 0.411T308 D D 2.1 0.8
7° 2NC-DCGW11T304WG D D 22.3
9.525 3.97 4.40.4
11T308WG D D 2.1 0.8
7° 2NC-DCGW11T304WH D D 22.1
9.525 3.97 4.40.4
11T308WH D D 1.8 0.8
11°3NC-TPGW110302 D D
32.4
6.35 3.18 3.40.2
110304 D D 2.3 0.4110308 D D 2.0 0.8
11°3NC-TPGW160402
32.4
9.525 4.76 4.40.2
160404 D D 2.3 0.4160408 D D 2.0 0.8
5°2NC-VBGW110302 D D
23.2
6.35 3.18 4.40.2
110304 D D 2.8 0.4110308 D D 2.0 0.8
5°2NC-VBGW160402 D D
23.8
9.525 4.76 4.40.2
160404 D D 3.3 0.4160408 D D 2.5 0.8
7° 2NC-VCGW160404 D D 22.8
9.525 4.76 4.40.4
160408 D D 1.9 0.8
※型番末尾 WG:低送り用ワイパーチップ WH:高送り用ワイパーチップWG : Wiper insert for Low-feed type WH : Wiper insert for High-feed type
■マルチコーナーワンユースチップ/ボジティブ(穴つき)Multi-cornered,One-use Type/Positive(With Hole)
外 観Appearance
逃げ角ReliefAngle
型 番Catalogue No.
在庫�Stock
コ
ナ
数No ofCutting Edges
焼結体切刃長Cutting Edge Length
寸法�Dimensions(mm)
BNC2
010
BNC2
020
内接円Inscribed Circle
厚�さThickness
穴�径Hole
ノーズ半径
Nose Radius
11° 3NC-TPGW160404HS D D 32.3
9.525 4.76 3.40.4
160408HS D D 2.0 0.8
7° 2NC-VCGW160404HS D D 22.8
9.525 4.76 4.40.4
160408HS D D 1.9 0.8
■マルチコーナーワンユースチップ/ボジティブ(穴つき)Multi-cornered,One-use Type/Positive(With Hole)
外 観Appearance
逃げ角ReliefAngle
型 番Catalogue No.
在庫�Stock
コ
ナ
数No ofCutting Edges
焼結体切刃長Cutting Edge Length
寸法�Dimensions(mm)
BNC2
010
BNC2
020
内接円Inscribed Circle
厚�さThickness
穴�径Hole
ノーズ半径
Nose Radius
7° 2NC-CCGT060204N-FV D D 2 2.3 6.35 2.38 2.8 0.4
7° 2NC-CCGT09T304N-FV D D 22.4
9.525 3.97 4.40.4
09T308N-FV D D 2.3 0.8
7° 2NC-CCGT09T304N-LV D D 22.4
9.525 3.97 4.40.4
09T308N-LV D D 2.3 0.8
7° 2NC-DCGT070204N-FV D D 2 2.4 6.35 2.38 2.8 0.4
7° 2NC-DCGT11T304N-FV D D 22.4
9.525 3.97 4.40.4
11T308N-FV D D 2.0 0.8
7° 2NC-DCGT11T304N-LV D D 22.4
9.525 3.97 4.40.4
11T308N-LV D D 2.0 0.8
11° 3NC-TPGT110304N-FV D D 32.3
6.35 3.97 3.40.4
110308N-FV D D 2.0 0.8
※型番末尾 FV:仕上げ切削用 LV:軽切削用FV : Chipbreaker for Finish cutting type LV : Chipbreaker for Light cutting type
刃先強化タイプHS型Strong Edge Type HS
ブレイクマスターBreak Masterワイパー
ワイパー
ワイパー
ワイパー
D印:標準在庫品 無印:受注生産品DMark:Standard Stock Item No mark: Made-to-order item
hyou4.indd 1 2015/04/21 9:35