User Guide SH100 pg

Conference Speaker SH100User Guide

User Guide SH100 pg

Charging the Bluetooth Conference Speaker Before you can use your Bluetooth Conference Speaker you need to charge the Lithium battery. Use the provided USB cable to connect the device to your computer to charge.

You will hear an indicator tone and see a solid red LED and a flashing blue LED when charging.

When the battery has fully charged, you will see a solid blue LED.

ON/OFF switch

Micro USB cable LED indicator

1

The Bluetooth Conference Speaker is now ready for connection. Disconnect the USB cable and slide the ‘ON/OFF’ switch to the ‘ON’ position.

User Guide SH100 pg

Pairing the Bluetooth Conference SpeakerTo pair the Bluetooth Conference Speaker, press and hold the ‘pair’ button until you see a rapid flashing red and blue LED. You will also hear an indicator tone.

2

Pair button

User Guide SH100 pg

Pairing the Bluetooth Conference SpeakerTo establish a connection, make sure you have enabled Bluetooth on the device that you want to connect to. Refer to the user manual that was included with your Bluetooth device on how to do this.

Once the device has found the Bluetooth Conference Speaker, select ‘SH100’. Some devices may require a pair code to be input, enter 0000.

The Bluetooth Conference Speaker will automatically pair with your device once it has been selected and you will hear an indicator tone to confirm.

3

The Bluetooth Conference Speaker will automatically connect to your Bluetooth device when it is turned on. You will hear two successive indicator tones when connected.

Taking callsWhen you receive an incoming call on your phone, you will hear an indicator tone from the Bluetooth Conference Speaker. If you are listening to music, the music will automatically pause.

To accept the incoming call, you can use your phone or press the ‘voice’ button. The call will come through the Bluetooth Conference Speaker and the built-in microphone will pick up your voice.

To end the call, you can use your phone or press the ‘voice’ button on the Bluetooth Conference Speaker.

Controlling music playbackVolume Use the volume controls or to increase or decrease the volume when playing music.

Pause/play Press the △ button to pause music playback. Press the button again to resume playback.

Track selection Press and hold the △ button to select the next music track. Press and hold the button to select the previous track.

User Guide SH100 pg 4

The volume/track selection and play/pause buttons are not available for devices connected to the 3.5mm audio input. Volume, track and play functions are controlled by the device connected.

Specifications:Frequency:2.4GHz ~ 2.48GHz ISM band

Speaker:Stereo 2.2W (4 Ω)

Microphone sensitivity:-58dB ± 2dB, S/N : 40dB

Bluetooth:V2.1

Profile:A2DP, AVRCP, HFP, HSP

Battery:1000mAh Lithium rechargeable

Charge time:Up to 2 hours for a full charge

Operating time:Up to 10 hours continuous

Standby time:Up to 100 hours

Pair code:0000

Interface:Micro USB (charging only)

User Guide SH100 pg

5Frequently asked questionsQ. The sound is very low or there is no sound output?

A. Please check the volume is turned up on the Bluetooth Conference Speaker and the volume control of your Bluetooth device. If you are using the 3.5mm audio input, make sure your audio cable is securely inserted into the speaker and your audio device.

Q. Music is playing on my Bluetooth device but it is not playing through the Bluetooth Conference Speaker?

A. Make sure your Bluetooth device has A2DP (Advanced Audio Distribution Profile) and make sure that your Bluetooth device is paired to the speaker.

Q. Hands free calling is not working with my mobile phone?

A. Make sure your mobile phone supports HSP (Headset Profile) and HFP (Hands-Free Profile) and make sure that your Bluetooth device is paired to the speaker.

5

User Guide SH100 pg

LED statusLED off - The speaker is turned off

Red LED off with slow flashing blue LED - The speaker is turned on

Red LED flashing and blue LED flashing - Pair mode

Red LED flashing - Battery is very low

Red LED and flashing blue LED - Battery is charging

The blue LED will turn on when the battery is fully charged.

6

User Guide SH100 pgwww.kaiserbaas.com