Bio 5SB Scanjet tank cleaning equipment

78-01

KEY FEATURES

+ Rotating spray

+ 360° cleaning pattern

+ Ideal for small tanks

+ Low pressure

+ Low use of cleaning medium

The Scanjet Bio 5SB is a new type of Rotary Spray Head (RSH) tank cleaning

device. Compared with conventional static devices, the Bio 5SB is very efficient,

saving water and chemicals while improving cleaning effectiveness. The Bio 5SB

employs a unique fluid bearing rotary mechanism, with a service life two to three

times that of traditional ball bearing rotary devices.

The choice of either a clip-on (pin), weld-on or threaded connection means the Bio

5SB is always easy to install, whether building a new CIP tank cleaning system or

upgrading an existing one based on ordinary static or rotary spray devices.

With 360° impact coverage, self-cleaning and self-draining features, the Bio 5SB

design follows EHEDG and GMP guidelines, and can be supplied with EN10204-2.1,

2.2 or 3.1 material and FDA 21CFR compliance certificates. The Bio 5SB-XXX-A

clip-on and weld-on versions have attained 3A certification under sanitary standard

78-01. Surface finish roughness supplied as standard is Ra = 0.8 μm (30 μ inch);

other surfaces are available upon request.

The Bio 5SB can be used in conjunction with the Scanjet WASHTRAC sensor to

monitor and verify its operation and performance.

The Bio 5SB is the first choice for anyone looking for the most advanced Rotary

Spray Head tank cleaning device available.

The Scanjet Bio 5SB Rotary Spray Head can be used in a wide range of

applications, including:

+ Mixing vessels

+ Blending tanks

+ Beverage tanks

+ Dairy tanks

+ Yeast tanks

+ Reactors

+ IBCs

1 1,5 2 2,5 3 3,5 4 4,5 5

0

2

4

6

8

10

20 30 40 50 60 700

5

10

15

20

25

30

35

40

Flow vs. Pressure

bar

psi

m3/h USgpm

1 1,5 2 2,5 3 3,5 4 4,5 5

0

1

2

3

4

0,5

1,5

2,5

3,5

Impact cleaning

20 30 40 50 60 70

0

1

2

3

4

5

6

7

8

9

10

11

12

13

m ft

bar

psi

Cleaning Radius

Wetting

360º SPRAY PATTERN

Ø 25.3/ 28.3(OD) (1/1.11 in)Ø 25.6/28.6(OD) (1/1.12 in)

PINCONNECTION

¾" BSPf¾" NPTf

THREADCONNECTION

Ø 25/22.5(ID) (0.98/0.89 in)

75

(2.9

5 in

)

Ø 45 (1.78 in)

WELDCONNECTION

¾" BSP¾" NPT

THREADCONNECTION

25/22,5(OD)

45

75

WELDCONNECTION

25,6/ 28,6(ID/OD)25,3/28,3(ID/OD)

PINCONNECTION

360º SPRAY PATTERN

* Clip-on models have approx. 0,5 m³/h higher flow rate

Technical performance Dimensions

Specifications

Flow* 4.1-9.8 m³/h (18-43 USgpm)

Inlet pressure 1-5 bar (14-72 psi)

Max pressure 5 bar (72 psi)

Recommended pressure 3 bar (43 psi)

Max working temperature 95°C (200°F)

Max ambient temperature 150°C (300°F)

Weight 137-175 g (4.83-6.17 oz)

Connections ¾” NPT or BSP

Weld connection

Pin connection

Material EN1.4404/PEEK

Lubrication Self lubricated by media

Pressure/Flow

Cleaning radius

Scanjet Systems AB P.O. Box 9316 SE-400 97 Göteborg SwedenPhone + 46 31 3387530 Fax + 46 31 3387540 E-mail sales@scanjetsystems.comWeb www.scanjetsystems.com

* Because of variations in part wear, water temperature, installation etc., the flow may differ ±10% from specified value.Continuous product improvement is the policy of Scanjet Group and we reserve the right to alter the specifications at any time without prior notice. Errors and omissions excepted.All trademarks, designs and other intellectual property depicted here are property of the Scanjet Group unless otherwise stated, and may be registered, patented or otherwise protected in certain jurisdictions.Copyright © Scanjet Group. All rights reserved.