Bill of Quantity for RCC Buildings

Sr. No. D E S C R I P T I O N Unit Quantity

Excavation & Backfilling Works.

1.0 Excavation & Backfilling upto 1.5m depth below FGL/NGL M3 1450

Excavation and backfilling around foundation and trenches/pits in all types of soil viz.earth, sand,gravel, clay, soft & hard murum etc. (excluding soft/hard rock) forfootings, steps, plinth beams, equipment foundations, drains, trenches, manholes,underground tanks/pits, etc including shoring strutting, dewatering where required(until foundation work is complete). Item also includes carting, stacking ifrequired,Spreading, levelling and compacting/consolidating surplus materials withinHPCL's premises or as per instructions of MMCI/HPCL Engineer In Charge (Rateincludes removal of any vegetation, small shrubs etc.)

2.0 from 1.5 m to 3.00 m below FGL/NGL M3 520

same as item 1 above but for 1.5m to 3.0m depth

3.0 Carting away material M3 620

Disposal / carting away surplus excavated earth / debris etc. outside HPCL's Black OilPlant premises to unobjectionable place identified by vendor.

4.0 Filling with good Earth M3 400

Filling with selected excavated earth available (Excavation excluded) & stackedelsewhere within HPCL's Black Oil Plant premises under floors or within plinth, opentrenches tank foundations etc.with approved quality of earth laid in layers notexceeding 300 mm in loose thickness including watering, ramming, levelling andcompacting to 95% Modified Proctor Density with use of mechanical rammers etccomplete as directed and instructed by MMCI/HPCL Engineer in charge.

5.0 Filling with Murrum M3 175

Supplying and filling murum of approved quality with PI of 1 to 7(Low plastic)containing not more than 20% cohesive fines namely clay and Max. dry density ofmaterial not less than 1.80 gms/cc, under floors or within plinth etc. includingidentifying & locating of borrow pits, excavation at borrow pits outside Plant premises;payment of Royalty to Owner of borrow pit, if applicable; payment of applicableroyalties, taxes, etc to Statutory Authority for operating the borrow pit; loading atborrow pit end; transportation from borrow pit to HPCL Premises; removing debris,organic matter, etc; spreading in layers not exceeding 300mm loose depth; dewateringduring course of filling, watering, compacting to obtain 95% of modified proctormaximum laboratory dry density all complete as per specifications and instructions ofMMCI/HPCL Engineer-in-Charge

Concrete and Allied Works NOTE: THE RATES FOR ALL ITEMS COVERED IN THIS SECTION SHALLINCLUDE COST OF DEWATERING, IF REQUIRED TILL COMPLETION OF WORKSUPTO GROUND LEVEL AND CHAMPHERS IN RCC WORKS SHALL BEPROVIDED WHEREVER REQUIRED AT NO EXTRA COST TO THE HPCL.ALSO THE CEMENT USED SHALL BE SLAG CEMENT.

6.0 PCC (1:4:8) M3 160

Providing and laying Plain Cement Concrete of nominal volumetric mix 1:4:8(1Cement: 4 Sand: 8 Crushed stone aggregates) with 40 mm and down size gradedaggregates below RCC foundations and grade slab & any other work as perrequirement including any required permanent brick masonry shuttering, dewatering,tamping, ramming, curing, etc all complete as per instructions of MMCI/HPCLEngineer-in-Charge.

SCHEDULE OF QUANTITIES FOR BLACK OIL AT VISHAKHA MARKETING TERMINAL RESITEMENT PROJECT TENDER FOR RCC BLDGS

d:\project\Bill of Quantity for RCC Bldg_08.07.09(BOQ(ter-17) Page : 1



7.0 PCC (1:3:6) M3 30

Providing and laying Plain Cement Concrete of nominal volumetric mix 1:3:6(1Cement: 3 Sand: 6 Crushed stone aggregates) with 40 mm and down size gradedaggregates below Masonry Wall foundations & any other work as per requirementincluding any required permanent brick masonry shuttering, dewatering, tamping,ramming, curing, etc all complete as per instructions of MMCI/HPCL Engineer-in-Charge.

8.0 RCC M 30 Below Plinth M3 900

Providing & laying in position Controlled grade Reinforced cement Concrete withdesign mix of required grade at all locations and levels using 20mm and down gradedaggregates in all types of works [including formwork, leaving pockets, placing ofconduits, making openings, pockets placing inserts / fanhooks sleeves in columns/beams/ slabs etc.] machine mixing, lifting, placing, machine vibrating, tamping, curingetc. as specified, complete as per drawings & / or as directed by MMCI / HPCLEngineer incharge. The cement used shall be slag cement.

NOTE: 1) The rate also includes cost of providing offsets, cutouts, formwork,construction joints, making holes in or cutting formwork for taking out dowel bars,hacking the exposed surfaces to receive plaster as necessary.Quoted rates toexclude the cost of supplying and providing Reinforcement Steel.All concrete for RCC works for footings/foundations, plinth beams, raft slabs,pedestals, columns, beams, walls, staircases, trenches, manhole pit, culverts, drains,sumps, pits equipment foundations, grade slabs (including form-work expansion,construction, control, isolation joints etc), kerbstones encasing of pipes etc at depthbelow and upto plinth level.

9.0 RCC M20 Concrete Below Plinth M3 250Same as above item no. 8 but with Grade of concrete M20

10.0 RCC M 30 above Plinth M3 880

Concrete for RCC works at all levels above plinth level for all structures, equipmentfoundations, columns, beams, floors, slabs, roof slabs, buildings lintels, guttersstaircases, fins, chajjas, pardis, sills, copings, projections, column/ beam encasingsetc.(up to a ht.of 12 mts.) above plinth level. The cement used shall be slag cement.

11.0 M.S. Round bars of Grade fe 250 TM 1Providing, laying & fixing in position reinforcement as per dwg. locations & levelsincluding bar bending schedules & obtaining MMCI/HPCL Engineer's approval,cutting,decoiling, straightening,cleaning, bending to required shape & binding withcontractor's own 16 SWG annealed binding wire including placing proper concretecover blocks, chair supports, Ceiling fan hooks etc. complete as specified anddirected by MMCI/HPCL Engineer in charge.

12.0 HYSD Bars of Grade Fe 415 TM 160same as above item but with HYSD conforming to IS:1786 / TMT bars of grade fe

415.13.0 Anchor bolts and relevant accessories like plates, nuts, pipesleeves etc. TM 1

Providing, fabricating and fixing in position at required locations to correct lines andlevels, pipe sleeves, nuts, anchor bolts for columns, floors, machine foundations,cable trenches and all types of RCC, PCC & masonry including necessary welding,machining, grinding, threading etc. Rate shall include providing, making andpositioning templates. (All materials & accessories required shall be provided byContractor).




14.0 Insert plates/ Nosing Angles/ Channels. TM 2Providing, fabricating and fixing in position at required locations to correct lines andlevels, angles, inserts for pits in RC buildings, foundations, pedestals, columns, slabs,beams & stairs , cable trenches and all types of RCC, PCC & masonry includingnecessary holdfasts , welding, machining, grinding, threading etc.Exposed surface willbe thorughly cleaned & painted with epoxy primer & paint. (All materials & accessoriesrequired shall be provided by Contractor).

15.0 Non shrink Grouting M3 1Providing & laying non-shrink cementitious premix type plain cement grout in C.M. 1:2including curing, preparation of surface etc. complete.

16.0 Anti-termite works SM 1760

Providing anti-termite treatment using CHLOROPYRIPHOS 20% EC (ISI marked) in 1% concentration as per IS 6313-1981 by creating a chemical barrier under and aroundthe wall, trenches, footings, basements, plinth & foundations junction of wall & flooralong the external perimeter of building, conduits etc. as per IS:6313 all complete asper instructions of MMCI/HPCL Engineer In Charge. (Mode of measurement shall besuperficial plinth area only).

Structural Steel and Allied Works17.0 Structural Steel TM 2

Providing, fabricating, welding and/or bolting, as required, erecting and fixing inposition all types of structural steel works (including applying two coat of red oxideprimer & 2 coats of approved shade synthetic enamel paint (of Berger/Asian orequivalent) to structural steel ) viz. columns, beams, monorails, rafters, trusses,purlins, frame for louvres, bracing, ladders and cage ladders, sag rods (except cheqd.plates, grating & pipe railing only) made up of rolled & built up sections with momentor shear connections, shop/site fabricated including all accessories viz. nuts, bolts,cleats, gussets, suspenders etc as per specification complete as directed by MMCI/HPCL Engineer incharge. The rate to include for welding weights, site connection,nut & bolts and same will not be measured for payment.(Painting & sand blastingshall be included in this item.) The rate shall include for preparing & providing detailedfabrication drawings based on design drawings & getting the same approved from theMMCI / HPCL Engineer incharge.

Note:Painting with primer & paint of approved quality & make including preparation ofsurface as per IS 2074-1992 or as per approved paint manufacturer spec. andincluding scaffolding etc. all complete as directed & instructed by MMCI / HPCLEngineer in charge.Min. thickness of 25 micron of each coat with total DFT (Dry filmthickness) 50 micron of paint & primer and application shall be as per approved paintmanufacturer's specifications. (Rate shall include cost of supply of paint.) Paymentwill be on the basis of weight of structural steel painted.

18.0 Pipe handrailing. MT 100

Providing, fabricating & erecting pipe handrailing made out of M.S. "C" class pipes(appr.1050mm high) with 32NB dia. pipe hand rail,2-20mm NB dia pipe knee rails and100 x 5mm thk. toe plate with 32NB pipe vertical support spaced at approx.1500 c/cand at corners & change of direction. Also including assembly for fixing to inserts orstringer beams complete in all respects including surface preparation for painting and2 coats of red oxide zinc chromate primer & two coats of 1st quality synthetic enamelpaint of approved make & shade all as directed & instructed by MMCI / HPCLEngineer incharge (Pipe shall be supplied by contractors)

NOTE: Items shall be measured as total length of completed pipe railing. (notindividual pipe lengths)




Masonry and Allied Works 19.0 230 mm thk. Solid Fly Ash Brick Masonry in superstructure. M3 540

Providing & constructing Solid Fly Ash brick masonary walls (as per masonry & plasterspecifications) using bricks of first quality (class 3.5 as per IS:12894, Compressivestrength of Brick 35 kg/cm2) of approved source at all locations and levels withcement mortar 1:5 including scaffolding, raking of joints, watering but excludingcement plaster finish complete as directed and instructed by MMCI / HPCL Engineerincharge.(up to a lift of 12 m locations). Portland Pozzolana Cement (conforming toIS:1489 Part 1 & 2) to be used for the preparation of Cement-Sand Mortar.Reinforcement in mullions & transoms shall not be separately paid. Providing andplacing formwork etc for transoms/mullions etc shall be included in the quoted rate.

20.0 230 mm thk. Solid Fly Ash Brick Masonry in steps, ramps etc. M3 15Same as above item no but in steps, foundation of steps, ramps, manholes, drainsinspection chambers etc.

21.0 115 mm thk. Solid Fly Ash Brick Masonry in superstructure. SM 360

Providing and constructing 115mm thick solid fly-ash brick walls (as per masonry &plaster specifications) in super structure using first quality bricks of approvedmanufacturer in cement mortar (1:4) including necessary scaffolding,raking of joints,watering etc. With R.C. stiffners as per specification. Transoms & mullions shall beprovided in the brick work when length or height of wall exceeds 2M.Transoms shallbe provided at lintel/door height. Spacing of mullions shall not exceed 1.5M c/c.Size of transoms/mullions shall be 115mm x 115mm with M15 grade concrete &10mm down graded aggregate only. Portland Pozzolana Cement (conforming toIS:1489 Part 1 & 2) to be used for the preparation of Cement-Sand Mortar.Reinforcement in mullions & transoms shall not be separately paid. Providing andplacing formwork etc for transoms/mullions etc shall be included in the quoted rate.

22.0 Internal Nerru Cement plaster 20mm thk. SM 3900

Providing & doing cement plaster in C.M. 1:4 mix to all RCC & masonry work at alllevels and locations including grooves, pattas,drip moulding, scaffolding, watering,raking out joints in masonary or concrete work as per masonry & plaster specification.The rate to include providing and fixing of 200mm wide chicken wire mesh of 26G &15mm mesh size at the junction of different construction materials.The cement usedshall be Portland Pozzolana Cement (Uniform Blended Portland cement with finepozzolana) conforming to IS:1489 Part 1 and Part 2

Internal Cement plaster 20mm thick. (First under coat of 17 mm and second finishingcoat of 3 mm as per specification)

23.0 Internal Nerru Ceiling plaster 15 mm thk. SM 1800

Same as item no. 22 but (First under coat of 12 mm and second finishing coat of 3mm)15mm thick ceiling plaster.

24.0 Internal Cement plaster 10mm thk. For surface to be tiled. SM 19010mm thick back up plaster for internal surface of RCC/Masonry work which is to betiled.

25.0 External Cement plaster 20mm thk. SM 3000Providing and doing external sandfaced plaster 20mm thk in C.M. 1:5 in 2 coats to allRCC and masonary works at all locations and levels including required grainfinishing, curing etc. complete as per specification and as directed and instructed byMMCI / HPCL Engineer incharge.The cement used shall be Portland PozzolanaCement (Uniform Blended Portland cement with fine pozzolana) conforming toIS:1489 Part 1 and Part 2NOTE: The rates includes the cost of the base coat of not less than 12mm thk.,external patta, drip moulds, curing and providing and fixing 200mm wide G.I. chickenmesh 26g thk. & 15mm mesh size at junctions of brick and RCC/PCC work etc. aswell as providing and mixing waterproofing compound of approved make in both coatsas per manufacturers specifications.

26.0 230mm thk. Rubble Soling with Roller and or mechanical rammers SM 190Providing, supplying and doing 230 mm thick dry rubble stone packing/soling underfloor, foundation, pavement, roads, steps, ramps & other similar locations, handsetvertically in rectangular lines, interstices filled in with smaller stone chips includingwatering, compacting/consolidating & finishing to the required levels and lines etc withthe use of 10 Ton roller and or with mechanical rammers complete as directed byMMCI/HPCL Engineer-In- Charge. (Blinding layer shall be of metal, sand or murrumsupplied by contractor)




27.0 230mm thk. Rubble Soling with Manual Compaction SM 1475Same as above but 230 mm thick rubble packing/soling and compacting the samewith manual tamping only at locations where mechanical rammers/rollers can not bemoved. (Rubble supplied by contractor)Floor Finishes Waterproofing and Allied Works

28.0 Kotah stone in flooring SM 290Providing & laying 50 mm thick Polished Kotah stone flooring of approved qualitymachine cut, machine polished kotah stones of specified size and thickness in greenor grey or approved tint in pattern & layouts as per drawing over a bed of 20mmC.M.1:4 including curing & polishing smooth as per specifications & as directed &instructed by MMCI / HPCL Engineer In charge.NOTE :- Kotah stone of 600 x 600mm size & 30 mm thick in flooring.

29.0 Kotah stone in Treads and Risers SM 140 Same as above 50 mm thick Polished Kotah stone flooring in treads , riser , landings. (One piece 25mm thk polished kotah stone )

30.0 Kotah stone in Skirting. MT 520Same as above but 100mm High & 25mm thick polished kotah stone In skirting laid

flush with the plastered painted surface.31.0 Granite in flooring SM 20

Providing & fixing 50 mm thick Granite flooring of granite tiles of approved make,colour & size having thickness 7mm including corners and curves laid on C.M. 1:4bedding of required thickness with neat cement float and filling joint with white/coloured cement in flooring all as directed and instructed by MMCI / HPCL EngineerIn charge.

32.0 Granite in Skirting MT 15Same as item no.31 above but for granite tiles in 100 mm high skirting

33.0 Ceramic Tiles in flooring SM 20Providing & fixing 40 mm thick flooring of ceramic tiles of approved make, colour &size having thickness 7mm including corners and curves laid on C.M. 1:4 bedding ofrequired thickness with neat cement float and filling joint with white/ coloured cementin flooring all as directed and instructed by MMCI / HPCL Engineer In charge. (Whitecement shall be provided by contractor).

34.0 Ceramic Tiles in Dado SM 190Same as Item No. 33 above but in dado to give surface flush with plastered/paintedsurface.

35.0 Vitrified Tiles in flooring SM 400Providing & fixing 40 mm thick flooring of vitrified tiles of approved make, colour & sizehaving thickness 7mm including corners and curves laid on C.M.1:4 bedding ofrequired average thickness of 10 mm with neat cement float and filling/finishing thethin joints in white cement including provision for fixing all required specials, cutting oftiles and grouting etc complete as specified and directed. vitrified tile size 600mm x600mm

36.0 Vitrified Tiles in Skirting MT 260

Same as Item No.35 above but in skirting 100mm high flush with plastered surface.

37.0 Acid Resistance Tiles in flooring SM 15Providing and fixing Acid Resistant Flooring 50 mm thick including acid resistantbedding, jointing with acid resistant plasticised sulphur cement as per manufacturer'sspecifications. Mandana stones

38.0 Acid Resistance Tiles in skirting MT 14Same as above item no. 37 but for skirting

39.0 IPS in flooring SM 1650

Providing and laying 50 thick cement concrete granolithic or Indian Patent Stone (IPS)Floor topping laid in alternate panels having uniform size and the area of panel shallnot be more than 2 sq. m with 1:1:2 cement concrete with graded course aggregatesize 10 mm and down including all formwork, 2mm thick PVC separator strips, mixingthoroughly compacting to finished thickness and levels, rendered smooth by trowellingand floating to produce hard and close knit surface, including roughening the surfaceof base concrete slurry thoroughly brushed into the surface, cutting by ponding,shuttering the edges etc. complete as directed by MMCI/HPCL Engineer in charge.




40.0 IPS in Stairs SM 30Same as above item no. 39 but IPS Flooring laid on RCC Staircase treads andlandings

41.0 Granite for kitchen platform SM 20Providing & fixing granite slab 25mm thk. of approved make & shade as kitchenplatform top with machine cut-machine polished edges over a base of 38mmcuddapah & cuddapah verticals with necessary skirting of 100mm at wall and 150mmwide facia in front for horizontal & vertical supports

42.0 Granite in stairs SM 25Same as above item but on stair treads and risers

43.0 Gravel flooring SM 600Providing and laying 150 mm thick gravel floor of 20 mm size gravel around pumps,DGs, Transformers, equipments etc

44.0 DPC SM 100Providing & laying damp proof course 40mm thick in P.C.C. 1:2:4 using 12mm size &down grade waterproofing compound 3% by weight of cement or as permanufacturers specifications finished rough including cleaning, curing etc completeas specified and as directed by the MMCI / HPCL Engineer In charge.

45.0 Terrace water proofing SM 1400Providing & laying seven courses of water proofing bitumen felt including finishing theterrace surface, providing & laying PCC 1:2:4 with 12.5 mm down size aggregates,screed laid to slope under bed for terrace water proofing. Rate to include dewatering,tamping, curing, flashing, concrete fillets, making grooves in masonry for flashing,filling grooves with 1:4 cement mortar all complete as per specifications & instructionsof MMCI/HPCL Engineer in charge.

Note: Waterproofing work shall carry a written guarantee of 10 years. Measurementshall be as per actual projected finished roof area of water proofing treatment.

46.0 Water proofing for chajja, canopies and gutters SM 130Providing & laying cement based surface water proofing by M/s. India waterproofingCo. or equivalent approved agency with metal screed of required thickness includingvatas, slopes drip moulds etc. complete as per specification & as directed &instructed with ten years written guarantee of performance.

47.0 Water proofing for Toilet sunk SM 20Providing & laying cement based surface water proofing by M/s Indiawaterproofing Co. or equaivalent approved agency for toilet sunk portion withbrickbat coba avg.115mm thk finished at top water proof scratch coat surface toreceive tiling/ floor finishes etc. complete in all respects as per the specifications with10 years written guarantee of performance in approved format all at directed &instructed by MMCI / HPCL Engineer In charge. NOTE: (Payment shall be made onmeasurement of finished plan area only).Door, Windows ,Gates ,Ventilators & Rolling Shutters Works

48.0 Aluminium doors with partly glazed & partly aluminium SM 25

Supplying & fixing anodised aluminium single leaf or double leaf doors with frames ofsize 100mmx45mmx3.18mm thick, double action with shutter frames of vertical style85mm x 45mm x 2.5mm thick frame, and horizontals of 100mm x 45mm x 2.5mm withbeading clips, EPDM gaskets, night latch, stopper, glazing with 6mm, clear floatglass panes / obscure glass panes of special selected quality with 300 sq. mmvision panel, full handles on both sides of all shutters made of 75mm x 8mm anodisedaluminium plate, stainless steel screws, door closures/heavy duty floor springs,hinges, strengthly of hinged styles of approved hardware etc. complete. AllAluminium material shall be Indal/ Jindal and or Equivalent approvedmanufacturer, minimum 25 micron Anodising, & as per detailed drawings andspecifications & as directed/ instructed by MMCI / HPCL Engineer In charge.

Note:- Two coats of bituminous paint to aluminium surface in contact withconcrete.with Partly glazed and Partly aluminium sandwitch panel sandwitched with 9mm thk. marine ply overlaid with 18 guage (1.2 mm) thick Anodisedaluminium sheet on both sides & 6 mm float glass glazing.

49.0 Fully glazed Aluminium doors SM 10same as above with fully glazed 6 mm clear float glass

50.0 Aluminium doors with obscure glass vision panel SM 25

same as above with but for partly glazed with obscure glass with 300 mm sq. visionpanel and partly aluminium sandwitch panelled with 9 mm thk marine ply.




51.0 PVC Doors SM 25Providing & fixing PVC Sintex or equivalent door with shutter consisting of shutterframe made of extrude plastic section having dimensions of 60x24mm anodized withmulti chambered hollow plastic section of 200x20mm with an average wall thicknessof 1mm jointed with one another by a tongue and groove joints and outer frame ofdoor made of extruded plastic section of 68x60mm or nearest on all sides includingproviding and fixing all required fiiting such as anodized aluminium butt hinges , towerbolts handles with screws,MS hold fasts for fixing door frames etc. complete as permanufacturer's specification.

52.0 Rolling Shutters SM 30

Providing & fixing Rolling shutters of 18 gauge GI, 75 wide rolled plates with 12mmlap, concave corrugation, complete with "one piece" construction, pressed steel75mm channel guides,ball bearings, bolts, brackets, flat springs, door suspensionshafts, locking arrangement, grills, including G.I.18 gauge top hood cover and2.5mm thick bottom plate with all necessary fittings/accessories all surface paintedwith two coats of primer and 2 coats of approved synthetic enamel paint finish. Allfitted & fixed complete as per the drawings and instructions of MMCI/HPCL EngineerIn charge.(Measurement for the payment shall be the area of shutter size clear).

53.0 HMPS doors SM 60Providing and fixing in position pressed steel hollow metal (HMPS)flush steel doorssingle leaf or double leaf 40 mm thick, shutters with 16 guage and pressed steelmetal frame with 18 guage of 230 mm or less in width, with necessay hold fasts, visionpanel, rubber buffers and lugs, gaskets including painting with 2 coats of red oxidezinc chromate primer and 2 coats of synthetic enamel paint with proper surfacepreparation, fixing all hinges. (All hinges & hardware shall be included in the itemrates)

54.0 Aluminium sliding Window with 6 mm clear glass SM 100Providing and fixing in position anodised aluminium sliding windows upto 3 tracksin extruded sections, outer frame having weep holes and water drainage section atbottom including PVC weather strips & glazing channels, nylon glider, rubber bumpersin interlocking sections, locking arrangement etc. complete as per specifications anddrawings with 6 mm clear glass

55.0 Aluminium louvered windows with exhaust fan SM 10

Same as above with aluminum louvered window with exhaust fan56.0 M.S. Steel windows and ventilators with 60 % openable SM 50

Providing and fixing in position M.S. Steel windows and ventilators as per IS:1038with standard rolled sections including 6 mm thick plain sheet glass with necessaryholdfasts, oxidised brass fixtures/fasteners, putty, glazing clips, or aluminium beading,peg stay, handle, screws etc. complete as per drawing and specifications including 2coats of red oxide zinc chromate primer and 2 coats of synthetic enamel paint ofapproved make, colour & shade etc complete as specified and directed.

57.0 fixed M.S. Steel windows, ventilators and windows with ventilators SM 10

same as above with fixed windows/ventilators

58.0 M.S. Steel louvered windows/ventilators. SM 60

same as above with louvered windows/ventilators

59.0 M.S. Steel louvered windows & exhaust fan SM 4

same as above with louvered windows/ventilators with exhaust fans60.0 MS gate SM 30

Providing and fixing the MS Gate single/double shutter with L 75X75X8 Main Frame &internal braced L members L65X65X6 conforming to IS:808 fitted with GI Chainlinkmesh (50mm sq. meshx3.15 mm GI) and required fittings & accessories liketowerbolts & internally welded to L frames as per drgs & instructions of MMCI/HPCLEngineer In Charge.

61.0 Chain Link fencing SM 600Providing and fixing GI Chainlink fencing 50mm sq. mesh x 3.15 mm GI Chainconforming to IS: 2721 with 2 m high vertical angle posts L75x75x8 at 2500 c/c;(having chain link fencing fixed to angle posts by using 'j' nut-bolts and machinestraightened 10 dia .M.S. Rod) including 300-500 sq. 600 deep PCC (1:2:4)foundation bed blocks




Painting Works 62.0 Exterior Paint SM 3050

Providing and applying one coat of approved primer & two coats of ExteriorEmulsion paint of Asian make (ACE Paint) or equivalent of approved shade to allexternal surfaces of cement plastered work or concrete including scaffolding,preparation of the surfaces as per manufacturers requirements. Crack filling withapproved filler material, curing etc. complete as per manufacturers specifications & asdirected by MMCI / HPCL Engineer incharge

63.0 Interior Paint SM 5850Providing & internal painting one coat of primer, one coat of putty and three coats offlat oil bound distemper paint of approved shade & make, carrying out the work asper manufacturer specification including cleaning the internal surface preparation,staging/scaffolding etc. complete and as directed by MMCI / HPCL EngineerinchargeSanitary Fittings & Fixtures

64.0 W.C. Indian type with flushing cisterns PC 7

Providing & fixing Indian W.C. pan Orissa pattern 580 x 440 mm size with Box Rimwith P or S trap including flushing cisterns, Flush valve, brass float valve (Front orRear entry as required) of approved make & colour shade 100mm dia. C.I. connectorupto soil stack or inspection chamber making flushing water & vent pipe connectionswith lead pipe for flushing connection & C.I. pipe for vent connection encasing offlushing connection in concrete & filling balance portion of W.C. with brick batconcrete etc. complete. ( Minimum sinking of floor to be 45 cms) ( at a distance of 60cms from door - if sinking is inclined)

65.0 W.C.European type with flushing cisterns PC 7

Providing & fixing in position floor mounted European water closet with P or S trapincluding flushing cisterns & sprout, Flush valve, brass float valve as required - blackcommander make of Champion brand seat cover with CP brass hinges rubberbuffers & 100 mm CI connector upto soil stack or Inspection Chamber (as the case may be) with providing & making a hole in wall & making it good and providing &making a flushing connection & vent pipe connection etc. complete includingproviding all material hinges, fittings etc. for the connection. The approved colour andmake as per instructions of MMCI/HPCL Engineer in charge.

66.0 Urinals PC 10Providing & fixing in position large flat back urinal height 61 cms width 40 cmsincluding brackets spreader making water connection including necessary pipingdrain connection with push type CP valve, C.P. waste coupling, C.P. Brass BottleTrap along with extention piece-wall flange and connection to a Drain Header etc.complete.The approved make and colour as directed by the MMCI/HPCL Engineer incharge.

67.0 Granite Partition for urinals PC 10Providing & fixing granite partition 20mm thick polished on both sides betweenurinals.(Size 450x1200)

68.0 Wash Basin (Rectangular) PC 3Providing & fixing Rectangular wash basin including C.I. brackets,C.P. waste coupling,C.P. bottle trap chain & plug C.P. stop cock at supply end one long body C.P. pillarcock connecting tubing drain connection etc. complete. The approved make andcolour as directed by the MMCI/HPCL Engineer in charge.

69.0 Wash Basin (Oval) PC 3Providing & fixing oval counter type wash basin 55cmx40cm with C.I. brackets,including C.P. waste coupling, C.P. bottle trap, chain & plug, C.P. stop cock at supplyend, one swan neck long body pillar cock connecting tubing drain connection etc.complete. The approved make and colour as directed by the MMCI/HPCL Engineer incharge.




70.0 Granite counter for wash basin PC 2Providing & constructing a granite counter for wash basin with a pair of verticalsupports of polished granite (one pair on each side of wash basin) formingsandwitch with cement morter polished caddapa stone (Polished side facing down)with cutout suitable for wash basin for supporting of wash basin & min. 25mmthick polished granite slab on top of cuddapa forming sandwitch fixed withcement morter, making a cutout in granite slab suitable for wash basin drilling holefor pillar cock & polished decorative moulding on cutout & on external face ofgranite & providing 75mm wide vertical granite facia to vertical supports & 300 wide(Patta) horizontal facia under the counter.

71.0 Kitchen sink PC 1Providing and fixing stainless steel kitchen sink (600 x 450 x 250 mm deep approxsize) of Hindustan Twyford make or any other equivalent approved make withstopcock, pillar cock, waste couplings, CP bottle trap, rubber plug and CP brasschain CI brackets, drainage connection water supply with drain board and plumbinginstallations up to external wall etc complete as directed and instructed by MMCI /HPCL Engineer incharge

72.0 Nahani Trap PC 10

Providing and fixing C.I. nahani trap with stainless steel grating including layingnecessary C.I. drainage pipe of minimum 100mm dia upto the external walleverything as per requirements of local authorities etc. complete in all respects asdirected and instructed by MMCI / HPCL Engineer incharge

73.0 Gully trap PC 10Providing and fixing in position stone ware gully traps 150 x 150mm size withcover including brick masonary chamber of clear internal size as 300mmx300mmwith cement plaster finishes externally and internally all in CM 1:4 mix including C.Iframe and hinged cover (Heavy duty) etc. everything as per requirements of localauthorities etc. complete in all respects as directed and instructed by MMCI / HPCLEngineer In charge Plumbing and Drainage Works

74.0 Inspection Chamber upto 1.5 m deep PC 3Providing and constructing brick masonry inspection chambers having internal cleardimensions 600x600, 900x600 , 750x750mm and depth upto 1.5 m etc. with230/345mm brick masonary in cement mortar (1:4) mix, 20mm thick cement finishplastered internally and externally in cement mortar 1:4 mix including necessaryexcavation, foundation concrete 1:3:6 mix 150mm thick, top cover with 100mm thickRC slab in M20 concrete with reinforcement at 100 Kg/M3 of concrete S.W.G.half round channels 150mm dia, concrete haunches, heavy duty C.I. manhole coverapprox. 450mm dia. and frame 16mm dia. C.I. rod rungs at 300 mm c/c etc.complete as shown on the drawing and/or directed and instructed by MMCI / HPCLEngineer In charge.NOTE: (Brick work to be 230mm thick upto 1.0.M depth and345mm thick beyond 1.0M upto 2.0M depth).

75.0 Ball Cock 12 mm dia PC 6Providing and fixing brass body heavy duty ball cock with PVC float includingnecessary fittings & fixtures as instructed & directed by MMCI / HPCL EngineerIncharge.

76.0 Shower rose PC 3Providing and fixing shower rose & assembly with built in hall joint for instantdirection of changes "R-51 Jetflow" type. Approved make& colour as directed byMMCI / HPCL Engineer Incharge.

77.0 GI pipe with 40 mm dia MT 150Providing, laying & jointing G.I. pipes, 'C' class including all fittings and specialssuch as bends, unions, elbows, couplings, tees, crosses, reducers, enlargers,stop- ends, plugs etc. with including providing & making chases in brickwork/RCC,providing & making Anticorrosion treatment to pipes consisting of a coat of Tar andcovering with Bitumen impregnated hessain cloth - Hydrotesting of pipe to ensureabsence of any leakage & making good of chase in C.M. 1:3 after fixing chicken meshafter the completion of installation of piping. etc as per requirements of localauthorities, complete in all respects as directed and instructed by MMCI / HPCLEngineer In charge




78.0 GI pipe with 25 mm dia MT 50same as above with 25mm dia.



81.0 Toilet Paper holder PC 15Providing and fixing in position C.P. toilet paper holder including toilet paper rollof approved quality and make etc. complete as directed and instructed by MMCI /HPCL Engineer In charge

82.0 5 mm thk. Glass Mirror PC 10

Providing and fixing in position plate glass mirror 400mm x 600 mm x 5 mm thickof Modi float or equivalent approved make over 6 mm thick waterproof plywood withwooden moulding at top and bottom including necessary hardware and syntheticenamel painting of approved shade to moulding all complete.Approved make andcolour as directed & instructed by MMCI/HPCL Engineer in charge.

83.0 Soap Dispensers PC 10Providing and fixing in position C.P. Brass liquid soap dispensers of approvedquality and design etc. complete as directed and instructed by the MMCI /HPCL Engineer In charge

84.0 Towel Rods PC 10Providing and fixing in position C.P. M.S. Towel rods 750mm long, 20mm dia.with necessary fittings of approved quality and make etc. complete as directed andinstructed by MMCI / HPCL Engineer In charge

85.0 150mm dia uPVC rain water pipe MT 170Providing, supplying, clamping and fixing 150 Dia uPVC rain water downtake pipesfrom terraces to the ground level including providing of all required accessories etccomplete as per drawings

86.0 150mm dia uPVC for sewage disposal MT 100

Supplying, delivering and laying 150mm dia. uPVC pipe (6 kg/cm2 quality) ofapproved make for Sewage disposal including bends, offsets, 'Y'-s / Tees etc., jointingwith solvent cement etc all necessary puddle flanges for joints of PVC and manholesaccessories confirming to IS-4985 testing, rectification, filling partly with sand includingrequired excavation and backfilling the trench etc. everything as per local authoritiesetc. complete in all respects as directed and instructed by MMCI/HPCL Engineer incharge. (Earthwork excavation and filling the sand will not be paid separately.)

87.0 HDPE Pipe 150mm Dia MT 100Supplying and laying of 150 mm dia HDPE pipes of heavy duty & first quality asapproved by MMCI/HPCL Engineer Incharge.Scope include supply & laying of all thenecessary pipe bends,socket/collars required for joining the pipes etc. complete asdirected by MMCI/HPCL Engineer InchargeMiscellaneous Works

88.0 water Tank of 1000 litres capacity PC 4Providing and erecting ready made storage tanks of 'Sintex' or equivalent approvedmanufacturer and required size and shape including connecting necessary supplylines, delivery lines, wash water line and with manhole cover at top of not less than450mm clear dia, with locking arrangement complete as per drawing and as directedand instructed by MMCI / HPCL Engineer In charge

89.0 water Tank of 5000 litres capacity PC 2same as above but with 5000 lit. capacity

90.0 20mm dia GI Water Spouts PC 20Providing & fixing in position 20 mm dia G.I. water spouts average 300 mm long withattached elbow fittings including finishing, making good etc. complete as directed andinstructed by MMCI / HPCL Engineer In charge

91.0 Plinth Protection SM 400Providing & doing plinth protection around building including excavation,230mmrubble soling, 100 mm thk. PCC M10 (1:3:6) with broom finish & as directed andinstructed by MMCI / HPCL Engineer In charge




92.0 False Ceiling SM 100

Providing and installing of removable type aluminium false ceiling system forhorizontal inclined and vertical comprising of square edge plane panels, 84mm wide x15 mm deep with 25mm recessed flanges, formed out of 0.5 mm thick aluminium alloyelectrically powder coated in standard colour shades as approved by theMMCI/HPCL Engineer In Charge. The panels shall be fixed on formed carriers, 15mm wide at top 43 mm deep made out of 0.19 mm thick aluminium alloy electricallypowder coated in stain black with protruding ears to hold panels in module of 100 mm,with 16 mm gap between the panels, carrier spacing shall be maximum 1.3 M c/c.

Carriers to be suspended from the slab or roof by 4 mm dia. galvanised steel wire orrod hangers with height adjustment suspension springs made out of galvanisedspring steel. Hangers shall be fixed to roof or slab by J-hooks and nylon inserts.Edges of the ceiling shall be neatly trimmed with suitable matching edge profiles tocover the gap between the false ceiling and the walls. Accoustical andthermal insulation blanket of 25 mm thickness of resin bonded mineral wool coveredin polythene bags shall be laid over the aluminium panel ceiling. The rate shall alsoinclude the cost of extra materials and labour required to support and fix A.C.diffusers, grills return air slits etc. in the ceiling system. All this work to be as perdrawing and as per Technical Specifications complete in all respects. Recommendedfalse ceiling system is LUXALON by M/s. LLOYDS or equivalent.

93.0 Ceiling POP SM 125

Providing and applying POP ceiling 6 mm thick with necessary surface preparation,finishing etc and as per instructions of MMCI/HPCL Engineer In-Charge

Lighting Fixtures 94 Tube light fittings -- TKC 24/236…(Main Substation & MCC Room) Each 175

Supplying & fixing of industrial type 2 x 36w FTL light fittings of Philips Make Ref .No.TKC 24/236 or its equivalent make approved by HPCL. Scope includes supplying &Wiring with 3 runs of 2.5 Sq.mm PVC insulated copper conductor in suitable surfaceconduiting manner and type of conduit shall be MS conduit for the wiring above thefinished surface, having 6/10 A MCB, Junction Boxes and PVC insulated copperconductor for light as per group control point wiring specification. Work includes allwiring accessories complete as reqd & include cost of junction box, wires, pipes etc.,cost of digging chases & refilling the same with CM 1:4 & making the wall good asrequired Note: The distance from the board to first tube light fitting shall be approx. 20m.

95Tube light fittings -- TKC 24/236… (For Security Room, Weigh bridge cabin,Worker's Amenity Room, Rail Staff Room )

Each 44

Supplying & fixing of industrial type 2 x 36w FTL light fittings of Philips Make Ref .No.TKC 24/236 or its equivalent make approved by HPCL. Scope includes supplying &Wiring with 3 runs of 1.5 Sq.mm PVC insulated copper conductor in suitable PVCconcealed conduiting manner and type of conduit shall be as per local statutoryrequirement , having 5A/6A poly carbonate modular type with top pressed coverswitch control on suitable MS cover with box including 1.5 Sq.mm PVC insulatedcopper conductor for light, fan points etc. as required. Work includes all wiringaccessories complete as reqd & include cost of switches of Anchor ROMA make,ceiling roses etc. , cost of digging chases & refilling the same with CM 1:4 & makingthe wall good as required Note: The distance from the board to first tube light fittingshall be approx. 20 m.

96 Tube light fittings -- TMX 95 / 236…… ( Battery Room) Each 2

Supplying & fixing of industrial type vapour Proof 2 x 36w FTL light fittings of PhilipsMake, Ref. No.: TM x 95/236 or its equivalent make approved by HPCL. Scopeincludes supplying & Wiring with 3 runs of 1.5 Sq.mm PVC insulated copperconductor in suitable 2 mm thick PVC pipe in concealed conduiting manner and typeof conduit shall be as per local statutory requirement for the wiring , having 5A/6A polycarbonate modular type with top pressed cover switch control on suitable MS coverwith box including 1.5 Sq.mm PVC insulated copper conductor for light, exhaust fanpoints etc. as required. Work includes all wiring accessories complete as reqd &include cost of switches of Anchor ROMA make, ceiling roses etc. , cost of diggingchases & refilling the same with CM 1:4 & making the wall good as required Note: Thedistance from the board to first tube light fitting shall be approx. 20 m.

97 Tube light -Steet light Type…...HGS 120 Cover…..(Trafo yard) Each 10




Supplying & fixing of 1 x 36w FTL street light fittings of Philips Make, Ref. No.: HGS120 Cover or its equivalent make approved by HPCL. Scope includes supplying &Wiring with 3 runs of 2.5 Sq.mm PVC insulated copper conductor in suitable surfaceconduiting manner and type of conduit shall be M.S. conduit 2 mm thickhaving 6A/10AMCB, Junction Box and 2.5 Sq.mm PVC insulated copper conductor for light etc.asper group control point wiring specification. Work includes all wiring accessoriescomplete as reqd &, cost of digging chases & refilling the same with CM 1:4 & makingthe wall good as required.

98 Tube light -Mirror Optic Type………..( Planning Room) Each 14

Supplying & fixing of 2 x 36w CFL Industrial type light fittings of Crompton GreavesMake, Ref. No.: CRDIA 236 EB or its equivalent make approved by HPCL. Scopeincludes supplying & Wiring with 3 runs of 1.5 Sq.mm PVC insulated copperconductor in suitable PVC concealed conduiting manner and type of conduit shall beas per local statutory requirement , having 5A/6A poly carbonate modular type with toppressed cover switch control on suitable MS cover with box including 1.5 Sq.mm PVCinsulated copper conductor for light, fan points etc. as required. Work includes allwiring accessories complete as reqd & include cost of switches of Anchor ROMAmake, ceiling roses etc. , cost of digging chases & refilling the same with CM 1:4 &making the wall good as required Note: The distance from the switch board to tubelight fitting shall be approx. 20 m.

99 Post top lanterns Each 8Supplying and fixing of post top lanterns of Philips make GRC 40/125 LPF orapproved equivalent including all accessories and lamps.Ceiling Fan & Exhaust Fans

100 1200 mm dia Ceiling fan Each 18

Supplying & fixing of 1200 mm sweep Ceiling fan of Crompton Greaves or itsequivalent make approved by HPCL. Scope includes supplying & Wiring with 3 runs of2.5 Sq.mm PVC insulated copper conductor in suitable 2 mm thick PVC pipe inconcealed manner and in 2mm MS conduit for the wiring above the finished surface,having 5A/6A switch control on suitable MS cover with box including 2.5 Sq.mm PVCinsulated copper conductor for light, fan points etc. as required. Work includes allwiring accessories complete as reqd & include cost of switches of Anchor ROMAmake , ceiling roses, extension rods etc. , cost of digging chases & refilling the samewith CM 1:4 & making the wall good as required.

101 300 mm dia sweep Exhuast fan Each 3

Supplying & fixing of 300 mm sweep Exhaust fan of Crompton Greaves or itsequivalent make approved by HPCL. Scope includes supplying & Wiring with 3 runs of2.5 Sq.mm PVC insulated copper conductor in suitable 2 mm thick PVC pipe inconcealed manner and in 2 mm MS conduit for the wiring above the finished surface,having 5A/6A switch control on suitable MS cover with box including 2.5 Sq.mm PVCinsulated copper conductor for light, fan points etc. as required. Work includes allwiring accessories complete as reqd & include cost of switches of Anchor ROMAmake , ceiling roses, extension rods etc. , cost of digging chases & refilling the samewith CM 1:4 & making the wall good as required.

102 450 mm dia sweep Exhaust fan Each 22Same as above but of 450 mm dia and heavy duty type .Switch Sockets:

103 5/16A Switch socket point…( Regular Switch Socket ) Each 43

Supply and fixing of 3 - pin, 250V, 5/16A switch and socket combined with indicatorand fuse on suitable MS cover with box in concealed manner. Scope includessupplying and run of 2.5 Sq.mm PVC insulated copper conductor in suitable 2 mm thk.PVC pipe in concealed manner and in 2mm MS conduit for the wiring above thefinished surface from power plug to power DB etc. complete as required.

104 16/32A Switch socket point…….(A.C. Point) Each 2

Supply and fixing of TPN, 415V, 16/32A switch and socket combined with indicatorand fuse on suitable MS cover with box in concealed manner. Scope includessupplying and run of 4 Sq.mm PVC insulated copper conductor in suitable 2 mm thk.PVC pipe in concealed manner and in 2 mm MS conduit for the wiring above thefinished surface from power plug to power DB etc. complete as required.

105 20A A.C. Points Each 2Same as above item 3.2 but for supplying & providing 20A AC points wherevernecessary as directed by the Site-in-charge.Lighting & Power distribution Boards:

106 100A TPN DB with MCCB+ELCB Each 2d:\project\Bill of Quantity for RCC Bldg_08.07.09(BOQ(ter-17) Page : 12



Supply, Installation, Testing and Commissioning of Indoor 3-ph PDB comprising of 1No. 100 A TPN MCB + ELCB as incomer feeders, 13 Nos., 20 A SPN MCB’s asoutgoing feeders. dust & vermin proof (IP-42 protection). It shall be fabricated from16 SWG CRCA sheet steel enclosure & shall be of compartmentalised type (incomer,outgoings & termination compartments). LDB’s shall be provided with 100 A tinnedcopper phase and neutral bars and earth bar of suitable size with earth connectionbrought to outside. LDBS shall be suitable for bottom cable entries. Knock outs shallbe provided to receive incoming & outgoing cables. DBS shall be supplied with DIN-channel, neutral link & busbars. The bus bars shall be of Electrical grade aluminium &shall be supported rigidly to withstand fault level of 16KA for 1 sec. DBs shall undergoa treatment of degassing. pickling and two coats of primer before painting with twocoats of antocorrosive enamel paint

107 63A TPN DB with MCB+ELCB Each 1

Supply, Installation, Testing and Commissioning of Indoor LDB comprising of 1 No.63 A TPN MCB + ELCB as incomer feeders, 16 Nos. 10A SPN MCBs as outgoingfeeders. dust & vermin proof (IP-42 protection). It shall be fabricated from 16 SWGCRCA sheet steel enclosure & shall be of compartmentalised type (incomer,outgoings & termination compartments). LDB’s shall be provided with 100 A tinnedcopper phase and neutral bars and earth bar of suitable size with earth connectionbrought to outside. LDBS shall be suitable for bottom cable entries. Knock outs shallbe provided to receive incoming & outgoing cables. DBS shall be supplied with DIN-channel, neutra link & busbars. The bus bars shall be of Electrical grade aluminium &shall be supported rigidly to withstand fault level of 16KA for 1 sec. DBs shall undergoa treatment of degassing. pickling and two coats of primer before painting with twocoats of anticorrosive enamel paint

108 63A TPN DB with MCB+ELCB Each 5

Supply, Installation, Testing and Commissioning of Indoor3 Phase LDB comprising of1 No. 63 A TPN MCB + ELCB as incomer feeders, 4 Nos. 10A SPN MCBs and 5Nos., 20 A SPN MCB’s as outgoing feeders. dust & vermin proof (IP-55 protection).It shall be fabricated from 16 SWG CRCA sheet steel enclosure & shall be ofcompartmentalised type (incomer, outgoings & termination compartments). LDB’sshall be provided with 100 A tinned copper phase and neutral bars and earth bar ofsuitable size with earth connection brought to outside. LDBS shall be suitable forbottom cable entries. Knock outs shall be provided to receive incoming & outgoingcables. DBS shall be supplied with DIN-channel, neutra link & busbars. The bus barsshall be of Electrical grade aluminium & shall be supported rigidly to withstand faultlevel of 16KA for 1 sec. DBs shall undergo a treatment of degassing. pickling and twocoats of primer before painting with two coats of anti corrosive enamel paint.

109 32A TPN DB with MCB+ELCB Each 1Same as above but for Indoor 3- Phase LDB comprising of 1No.32A TPN MCB +ELCB as incomer feeder. 8 Nos. 10A SPN MCBs as outgoing feeders.TELEPHONE

110 2 Pair telephone wiring as mentioned belowRunning meters

250

Supply & laying of 2 pairs of 0.5 mm dia screened & shielded telephone wire in 20 mmdia PVC conduit partly/fully concealed in types of walls, floor etc. complete with allaccessories, wiring terminators, connected civil works, rough plastering etc includingsupply of 16 SWG GI fish wire conduit and accessories

111 RJ 11 Telephone connectors each 10Supply & fixing of modular type telephone connectors in suitable size PVC boxconcealed to wall including all civil works.

112 20 pair telephone junction box each 3Supply & fixing of 20 pair telephone tag block with crone connectors housed insuitable MS junction box.FIRE ALRAM SYSTEM

113 2 Pair fire alarm wiring as mentioned belowRunning meters

300

Supply & laying of 2 pairs of 2.5 mm core dia Un armoured FRLS Cable in 25 mm diaMS conduit partly/fully concealed in types of ceiling, walls, floor etc. complete with allaccessories, wiring terminators, connected civil works, rough plastering etc includingsupply of 16 SWG GI fish wire conduit and accessories

114 Back Box / Pull box with 4 terminals each 25Supply & fixing of 4 terminal MS back box /pull box.PUBLIC ADDRESS SYSTEM




115 2 Pair PAGA system wiring as mentioned belowRunning meters

150

Supply & laying of 2 pairs of 1.0 mm core dia Un armoured FRLS Cable in 25 mm diaMS conduit partly/fully concealed in types of ceiling, walls, floor etc. complete with allaccessories, wiring terminators, connected civil works, rough plastering etc includingsupply of 16 SWG GI fish wire conduit and accessories

116 Pull box / Back Box each 10Supply & fixing of MS pull box/back box with 4 terminals/connectorsTAS LAN

117 CAT 6, 4 pair twisted pair computer cable for TAS LANRunning meters

200

Supply & laying of CAT 6, 4 pair twisted computer cable screened and shielded in20/25 mm dia PVC conduit partly/fully concealed in types of walls, floor etc. completewith all accessories, wiring terminators, connected civil works, rough plastering etcincluding supply of 16 SWG GI fish wire conduit and accessories

118 RJ 45 Computer Connectors each 7Supply & fixing of modular type of RJ 45 computer connectors in suitable size PVCbox concealed to wall including all civil works. CCTV

119 Co-axial braided cable Running meters

50

Supply & laying of co axial, braided cable in 20/25 mm dia PVC conduit partly/fullyconcealed in types of walls, floor etc. complete with all accessories, wiring terminators,connected civil works, rough plastering etc including supply of 16 SWG GI fish wireconduit and accessories

120 BNC CCTV Connectors each 1

Supply & fixing of modular type of RJ 11 computer connectors in suitable size PVCbox concealed to wall including all civil works. MIS LAN

121 CAT 6, 4 pair twisted pair computer cable for MIS LANRunning meters

175

Supply & laying of CAT 6, 4 pair twisted computer cable screened and shielded in20/25 mm dia PVC conduit partly/fully concealed in types of walls, floor etc. completewith all accessories, wiring terminators, connected civil works, rough plastering etcincluding supply of 16 SWG GI fish wire conduit and accessories

122 RJ 45 Computer Connectors each 7Supply & fixing of modular type of RJ 45 computer connectors in suitable size PVCbox concealed to wall including all civil works.


Bill of Quantity for RCC Buildings

Documents

Transcript of Bill of Quantity for RCC Buildings