B&G care and Material formulations
-
Upload
black-and-white-indst -
Category
Education
-
view
100 -
download
1
Transcript of B&G care and Material formulations
B&G Care and Repair&
Material FormulationsTypes - Advantages - Disadvantages
B&G Care and Repair
Figure 1The brass nozzle should be cleaned with a toothbrush and a detergent; don't use a metal brush or sharp objects on the nozzle
Nozzle (see figure 1) - The brass nozzle determines the pattern (pin-stream or fan) of the liquid spray. The nozzle is made of thick brass and will survive being knocked around in the back of service trucks. However, with extended use, the openings for the fan sprays and the pin-stream will gradually enlarge. This increase will change the angle (80 degrees for the fine fan, 50 degrees for the coarse fan) of the spray, and the distribution of the liquid in the fan may become uneven.
The general appearance of the nozzle may not indicate that the openings have enlarged or are damaged. Replace the nozzle every two years to maintain an accurate spray pattern and flow rate.
Figure 2The filter is located between the hose and the valve; loosen the fitting, remove the filter and clean with a toothbrush. This filter keeps dirt out of the valve and nozzle, replace if it is lost.
Filter/Strainer (see figure 2) - The small filter/strainer should be removed, cleaned and replaced regularly. Regardless of the water source or insecticides used, small pieces of dirt and debris often get into the tank. The strainer keeps dirt from clogging the valve and blocking the spray. A toothbrush can be used to clean the strainer.
Figure 3A 3/8-inch, open-end wrench can be used to tighten the packing nut if the valve develops a leak.
Valve (see figure 3) - The Extenda-Ban valve is designed for long service without leaking. A leak in the gaskets may result in a small amount of liquid on the handle or at the end of the valve. Small leaks can be corrected by slight tightening of the packing nut (use a 3/8-inch wrench).
Figure 4The check valve, at the base of the pump cylinder, can be removed and cleaned, and the base of the cylinder (around the holes) should be cleaned of residue. Tightly replace the check valve, and be certain it is secure.
Check Valve (see figure 4) - The check valve at the base of the pump cylinder admits air into the tank as the pump handle is depressed. It can become worn and deposits around its edge (on the pump cylinder) can cause it to leak. Replacing the check valve (PV-266) will keep the pump working and maintain proper tank pressure. Cleaning the bottom of the pump cylinder with a small brush will remove deposits that build up around the edge of the check valve.
FormulationsTypes - Advantages - Disadvantages
D – dustG – granularS – solution WP – wettable powderEC – emulsifiable concentrateDF – dry flowableWDG – water dispersible granule
This is a listing of the more common abbreviations that describe formulations.
Formulations
• Evaluate advantages and disadvantages
• Do you have the right application equipment?
• Can the formulation be applied when and where it is needed?
• Will the formulation reach the target pest and be there long enough?
Selecting a Formulation
There are choices for you to make when selecting a product and the formulation
type can play a key role in your selection process.
Wettable Powders (WP)Emulsifiable Concentrate (E or EC)
MicroencapsulatedSelecting a Formulation
Theses are four popular formulations.
SUSPENSION CONCENTRATE (SC)
MicroencapsulatedParticles of pesticide active ingredient (liquid or dry) surrounded in a plastic coating; formulated product mixed with water and applied as spray. Following application the capsule releases the pesticide slowly or on contact by the insect.
Untreated Surface(un-painted wood-brick-concrete)
MicroencapsulatedNot absorbed by
Untreated Surfaces –Leaves behind
capsules that explode when disturbed
Mc Mc Mc
MicroencapsulatedADVANTAGES
increased safety to applicator; easy to mix, handle and apply; slow release of pesticide
DISADVANTAGES
constant agitation required; bees may pick capsules and take back to their hive
Active ingredient (liquid) dissolved in a petroleum-based solvent with
an emulsifier added
Turns white when mixed.Smells of solvents.
Emulsifiable Concentrate (E or EC)
Product Dilution
Untreated Surface(un-painted wood-brick-concrete)
Ec EcEc
Emulsifiable Concentrate (E or EC)Easily absorbed
by Untreated Surfaces
Ec
Emulsifiable Concentrate (E or EC)
ADVANTAGES• Easy to handle• Little agitation• Relatively easy on
equipment• Leaves little residue• Quicker knockdown
DISADVANTAGES
• Phytotoxic – plant injury
• Easily absorbed by the skin
• Flammable• Deterioration of
rubber and plastic hoses
Wettable Powders (WP)Wettable powders settle out quickly, therefore
require constant agitation in the spray tank
Product Dilution
Untreated Surface(un-painted wood-brick-concrete)
Wettable Powders (WP)Not absorbed by
Untreated Surfaces – leaves a film
(powder)behind
WP
Wettable Powders (WP)ADVANTAGES DISADVANTAGES
Inhalation hazard Constant agitation Difficult to mix in
hard water Abrasive to pumps
and nozzles Visible residues
Easy to store Easy to measure/mix Relatively less harmful to
plants, animals and surfaces than ECs
Less absorption by human skin and eyes
Suspension ConcentrateA stable suspension of solid pesticide(s) in a fluid usually intended for dilution with water before use. Ideally, the suspension should be stable (i.e. not settle out).
Suspension ConcentrateADVANTAGES DISADVANTAGES
A.I. tends to settle out over time.
Easy to store Easy to measure/mix Relatively less harmful to
plants, animals and surfaces than ECs
Untreated Surface(un-painted wood-brick-concrete)
Suspension ConcentrateNot absorbed by
Untreated Surfaces –
Choose a pesticide formulation that will best suit your pest problem and target site– Safety, ease of use
– Human exposure concerns
– Phytotoxicity; visible residues
– Application equipment considerations
Formulation Summary