BESI Armaturen Hydraulic Actuator 90° HST -...
15
BESI Armaturen Bremen Hydraulic Actuator 90° HST BESI Armaturen GmbH & Co KG Phone: +049 (0) 421 57 64 3 – 0; Fax: +049 (0) 421 58 36 21; eMail: [email protected] The reproduction, transmission or use of this document or its contens is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights erated by patent grant or registration of a utility model for design are reserved. Modification without notice. HST-V2-1 - edition: 15.09.00 BESI hydraulic actuators, type HSTP, are available in double-acting and single-acting spring-return design, and benefit from the high oil-pressure level – 100 up to 135 bar, on request up to 160 bar; thus they offer comparably small overall dimensions. They may be installed at any place – submerged below medium, in dry spaces, on deck, and in hazardous areas. Double-acting ¼-turn actuators need 2 hydraulic pipe connections for the supply of each valve; for spring- return valves only 1 hydraulic supply pipe is necessary. For easy installation we recommend endless pipes from coil, preferably bundled pipes, comprising 2 or more hydraulic lines. Torque The ¼-turn actuators provide continuous torque over the full swivel range, due to the transmission of hydraulic pressure via “rack and pinion”. In case of spring-return actuators, torque will be subject to the actual spring forces acting against the hydraulic pressure. They provide sufficient residual force for safe closing in case of control-medium failure or after closing signal. Position Response Valve position can be effected by limit switches mounted externally to the actuator, or by volume transmitters installed inside the central control unit – which may be the solenoid valve cabinet. The volume transmitters provide an inexpensive – but very precise and reliable – signal transmission, which eliminates the need for additional cabling to the valves. Volume transmitters are type-approved by Germanischer Lloyd and are accepted by all major classification societies. Further, 0 to 100%-indication and control is rendered with a potentiometer device. Medium Failure Single-acting spring-return valves will close immediately when the hydraulic pressure is released by signal or failure. The closing speed is controlled by a throttle in order to avoid water hammering effects. Double-acting actuators have the disadvantage of an inexact position on failure of control medium, i.e. the valve position may change in an uncontrolled manner. To avoid such adverse effects, external control blocks with controlled double-check valves are available; they prevent any change in the valve´s position when without control power. Emergency Operation If necessary the actuators can be equipped with quick connector couplings for connecting a portable manual emergency pump. For actuators installed inside tanks control blocks with these couplings are arranged outside of the tanks nearby and connected to the concerning actuators by hydraulic piping, thus allowing their manual control.
Transcript of BESI Armaturen Hydraulic Actuator 90° HST -...
BESI ArmaturenBremen
Hydraulic Actuator 90°HST
BESI Armaturen GmbH & Co KG Phone: +049 (0) 421 57 64 3 – 0; Fax: +049 (0) 421 58 36 21; eMail: [email protected]
The reproduction, transmission or use of this document or its contens is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights erated bypatent grant or registration of a utility model for design are reserved. Modification without notice. HST-V2-1 - edition: 15.09.00
BESI hydraulic actuators, type HSTP, are available in double-acting and single-acting spring-return design,and benefit from the high oil-pressure level – 100 up to 135 bar, on request up to 160 bar; thus they offercomparably small overall dimensions. They may be installed at any place – submerged below medium, in dryspaces, on deck, and in hazardous areas.Double-acting ¼-turn actuators need 2 hydraulic pipe connections for the supply of each valve; for spring-return valves only 1 hydraulic supply pipe is necessary. For easy installation we recommend endless pipesfrom coil, preferably bundled pipes, comprising 2 or more hydraulic lines.TorqueThe ¼-turn actuators provide continuous torque over the full swivel range, due to the transmission of hydraulicpressure via “rack and pinion”.In case of spring-return actuators, torque will be subject to the actual spring forces acting against the hydraulicpressure. They provide sufficient residual force for safe closing in case of control-medium failure or afterclosing signal.Position ResponseValve position can be effected by limit switches mounted externally to the actuator, or by volume transmittersinstalled inside the central control unit – which may be the solenoid valve cabinet. The volume transmittersprovide an inexpensive – but very precise and reliable – signal transmission, which eliminates the need foradditional cabling to the valves. Volume transmitters are type-approved by Germanischer Lloyd and areaccepted by all major classification societies. Further,0 to 100%-indication and control is rendered with a potentiometer device.Medium FailureSingle-acting spring-return valves will close immediately when the hydraulic pressure is released by signal orfailure. The closing speed is controlled by a throttle in order to avoid water hammering effects.Double-acting actuators have the disadvantage of an inexact position on failure of control medium, i.e. thevalve position may change in an uncontrolled manner. To avoid such adverse effects, external control blockswith controlled double-check valves are available; they prevent any change in the valve´s position whenwithout control power.Emergency OperationIf necessary the actuators can be equipped with quick connector couplings for connecting a portable manualemergency pump. For actuators installed inside tanks control blocks with these couplings are arranged outsideof the tanks nearby and connected to the concerning actuators by hydraulic piping, thus allowing their manualcontrol.
BESI ArmaturenBremen
Hydraulic Spring Return ActuatorHSTP-F
BESI Armaturen GmbH & Co KG Phone: +049 (0) 421 57 64 3 – 0; Fax: +049 (0) 421 58 36 21; eMail: [email protected]
The reproduction, transmission or use of this document or its contens is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights erated bypatent grant or registration of a utility model for design are reserved. Modification without notice. HST-F-V2-1 - edition: 15.09.00
BESI produces hydraulic single-action spring-return actuators type HSTP-F. In first attempt they weredesigned to ensure a defined fail-to-safe position – open or closed – when without control power. As benefitthey proved very economic - both as single unit and ready installed in a system - because of their single-lineconnection. Hydraulic actuators operate at an oil-pressure level of 100 up to 135 bar - on request up to 160bar – and offer very small overall dimensions. They may be installed at any place: below medium, in dryspaces, on deck, and in hazardous areas. Single-acting ¼-turn actuators need only one hydraulic pipe for theirsupply. For their easy installation we recommend endless pipes from coil, preferably bundled pipes.TorqueThe provided torque of spring-return actuators is subject to the actual spring forces necessarily acting againstthe hydraulic pressure. The actuators have to be selected with regard to the residual forces needed for safeclosing (or opening) in case of control-medium failure or after closing signal. Their sizes fit to all commonapplications in the shipbuilding industry.Position ResponseThe valve position can be detected by limit switches mounted externally to the actuator, or by volumetransmitters installed inside the central control unit – which may be the solenoid valve cabinet. The type-approved BESI-make volume transmitters are accepted by all major classification societies. They provide aninexpensive but very precise and reliable signal transmission, which eliminates any electric cabling to thevalves. This ensures economic installations even in hazardeous areas of a ship.Medium FailureSpring-return valves will close immediately when the hydraulic pressure is released by signal or failure. Theclosing speed is controlled by a throttle in order to avoid water hammering effects.Emergency OperationAs a unique safety feature the actuator provides a second independent piston for manual operation. Thisredundancy allows emergency operation completely independent from the hydraulic circuit, important insituations where the hydraulic circuit may be deferred. For manual operation a portable hand pump can beconnected to the actuator with a quick connector coupling. Spring-return actuators under medium will beconnected to an accessible control block outside the tank.
SelectionSpring-return actuators are applicable for all valves for which fail-to-safe function is mandatory or acceptable.Because of their single-line connection they ensure more economic installations even for short distances,compared with double-acting actuators with slightly lower unit price.
BESI ArmaturenBremen
torques and key of typefor hydraulic actuators
type HSTP-spring return
BESI Armaturen GmbH & Co KG Phone: +049 (0) 421 57 64 3 – 0; Fax: +049 (0) 421 58 36 21; eMail: [email protected]
The reproduction, transmission or use of this document or its contens is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights erated bypatent grant or registration of a utility model for design are reserved. Modification without notice. 1199_HST_s_torques.doc-1 - edition: 11.09.2000
torques working pressure = 100 bar (max. permissible pressure = 180 bar)
type torque (Nm) weightclose open (kg)
HSTP51 - 40/F 100 190 11,0
HSTP78 - 40/F 170 280 20,0
HSTP78 -63/F 420 690 32,0
HST2P78 - 60/F 650 1400 56,0
HSTP108 - 90/F 1100 2145 72,0
HSTP156 - 100/F 2025 3865 92
HST2P156 - 100/F 4050 7730
key of type . e.g. HST2P 78 – 50/50
H ST 2 P 78 - 50 / 50 : : : : : : xx = diameter (mm) of close cylinder : : : : : : F = spring return : : : : : : : : : : : xx = diameter (mm) of open cylinder : : : : : : : : : diameter (mm) of pinion : : : : : : : plunger design : : : : : =simple torque : : 2 = twofold torque : : 4 = fourfold torque : : : actuator : H = hydraulic P = pneumatic
BESI ArmaturenBremen
HSTP 51 – 40 / Fhydraulic spring return actuator 90°
BESI Armaturen GmbH & Co KG Phone: +049 (0) 421 57 64 3 – 0; Fax: +049 (0) 421 58 36 21; eMail: [email protected]
The reproduction, transmission or use of this document or its contens is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights erated bypatent grant or registration of a utility model for design are reserved. Modification without notice. 1100_HSTP51-40F-1 - edition: 11.09.2000
main data standard / on request
function spring closed / openedinstallation dry / submerged / open deckmounting direction cross / parallel to pipelineoperation connection = PA OD 8mm / OD 10 mmcoating alkyd resin primer
synthetic resin finishmax. working pressure 135 bartotal dry weight 11 kgoil displacement 44 cm³temperature range -20° - +80°Crotation 90° ±2°
options• electr. limit switch – IP65 / IP68 / EEx• potentiometer• direct mounted electro hydraulic power
pack (EHPP), controlled by one cable• manual declutchable worm gear• separate control block• special connections• special coating
hydraulic viscosities 15 – 46 cSt./40°Ctorque 100 Nm by springflange dimension ISO 5211 - F 05 = ø50-4xM6
ISO 5211 - F 07 = ø70-4xM8valve shaft dimensions
max. SW 16 mm
max. ø 19 mm acc. DIN 6885
max. SW 16 mm
general informationThe design ensures a defined fail-to-safe position – open or closed – in case of control powerfailure. They are very economic and reliable safe, because the BESI HSTP has:
• second independent piston for emergency operation• quick connection for emergency hand pump• visual position indication• just one connection pipe
BESI ArmaturenBremen
HSTP 51 – 40 / Fhydraulic spring return actuator 90°
detail list
BESI Armaturen GmbH & Co KG Phone: +049 (0) 421 57 64 3 – 0; Fax: +049 (0) 421 58 36 21; eMail: [email protected]
The reproduction, transmission or use of this document or its contens is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights eratedby patent grant or registration of a utility model for design are reserved. Modification without notice. 1100_HSTP51-40F-2 - edition: 11.09.2000
item object material pcs.1 body GG25 12 body cover C45 14 pinion shaft St52.3 15 pinion St52.3 16 rack C45 17 piston POM 18 washer C45 19 cylinder C45 110 spring body St52 111 bush POM 212 spring body cover C45 117 groove ring NBR 120 o-ring NBR 221 o-ring NBR 222 o-ring NBR 223 o-ring NBR 224 o-ring NBR 125 o-ring NBR 326 o-ring NBR 227 round bar PVC 228 oil level glass PA 129 disc spring spring St 2931 cup nut 1.4305 132 hexagon nut 1.4305 133 grub screw 8.8 134 hexagon screw 8.8 435 hexagon screw 8.8 436 socked head cap screwing 8.8 437 hexagon screw 8.8 438 hexagon screw 8.8 139 hexagon nut 8 143 blind rivet St 150 submerged connection block C45 152 straight pipe screwing St 153 quick coupling EMA3/R1/4“ St-galv. 1
BESI ArmaturenBremen
HSTP 78 – 40 / Fhydraulic spring return actuator 90°
BESI Armaturen GmbH & Co KG Phone: +049 (0) 421 57 64 3 – 0; Fax: +049 (0) 421 58 36 21; eMail: [email protected]
The reproduction, transmission or use of this document or its contens is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights erated bypatent grant or registration of a utility model for design are reserved. Modification without notice. 1101_HSTP78-40F-1 - edition: 11.09.2000
main data standard / on request
function spring closed / openedinstallation dry / submerged / open deckmounting direction cross / parallel to pipelineoperation connection = PA OD 8mm / OD 10 mmcoating alkyd resin primer
synthetic resin finishmax. working pressure 135 bartotal dry weight 20 kgoil displacement 71 cm³temperature range -20° - +80°Crotation 90° ±2°
options• electr. limit switch – IP65 / IP68 / EEx• potentiometer• direct mounted electro hydraulic power
pack (EHPP), controlled by one cable• manual declutchable worm gear• separate control block• special connections• special coating
hydraulic viscosities 15 – 46 cSt./40°Ctorque 170 Nm by springflange dimension ISO 5211 - F 07 = ø70-4xM8
ISO 5211 - F 10 =ø102-4xM10valve shaft dimensions
max. SW 30 mm
max. ø 35 mm acc. DIN 6885
max. SW 30 mm
general informationThe design ensures a defined fail-to-safe position – open or closed – in case of control powerfailure. They are very economic and reliable safe, because the BESI HSTP has:
• second independent piston for emergency operation• quick connection for emergency hand pump• visual position indication• just one connection pipe
BESI ArmaturenBremen
HSTP 78 – 40 / Fhydraulic spring return actuator 90°
detail list
BESI Armaturen GmbH & Co KG Phone: +049 (0) 421 57 64 3 – 0; Fax: +049 (0) 421 58 36 21; eMail: [email protected]
The reproduction, transmission or use of this document or its contens is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights eratedby patent grant or registration of a utility model for design are reserved. Modification without notice. 1101_HSTP78-40F-2 - edition: 11.09.2000
item object material pce.1 body GG25 12 upper cover C45 14 pinion shaft St52.3 15 pinion St52.3 16 rack C45 17 piston POM 18 cylinder St52.3 19 cylinder C45 110 spring body C45 111 guid bush POM 112 guid bush POM 113 location plug C45 114 washer C45 115 flange C45 120 o-ring NBR 121 o-ring NBR 222 o-ring NBR 223 o-ring NBR 124 o-ring NBR 225 o-ring NBR 126 o-ring NBR 227 o-ring NBR 328 piston gasket NBR 129 disc spring spring St 4330 oil level glass PA 131 cup nut 1.4305 132 hexagon nut 1.4305 133 grub screw St45 134 socket head cap screw 8.8 635 hexagon screw 8.8 436 socket head cap screw 8.8 437 socket head cap screw 8.8 442 blind rivet St 143 straight pipe screwing St 144 quick coupling EMA3/R1/4“ St galv. 148 submerged connection block C45 1
BESI ArmaturenBremen
HSTP 78 – 63 / Fhydraulic spring return actuator 90°
BESI Armaturen GmbH & Co KG Phone: +049 (0) 421 57 64 3 – 0; Fax: +049 (0) 421 58 36 21; eMail: [email protected]
The reproduction, transmission or use of this document or its contens is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights erated bypatent grant or registration of a utility model for design are reserved. Modification without notice. 1102_HSTP78-63F-1 - edition: 11.09.2000
main data standard / on request
function spring closed / openedinstallation dry / submerged / open deckmounting direction cross / parallel to pipelineoperation connection = PA OD 8mm / OD 10 mmcoating alkyd resin primer
synthetic resin finishmax. working pressure 135 bartotal dry weight 32 kgoil displacement 353 cm³temperature range -20° - +80°Crotation 90° ±2°
options• electr. limit switch – IP65 / IP68 / EEx• potentiometer• direct mounted electro hydraulic power
pack (EHPP), controlled by one cable• manual declutchable worm gear• separate control block• special connections• special coating
hydraulic viscosities 15 – 46 cSt./40°Ctorque 420 Nm by springflange dimension ISO 5211 - F 07 = ø70-4xM8
ISO 5211 - F 10 = ø102-4xM10valve shaft dimensions
max. SW 30 mm
max. ø 35 mm acc. DIN 6885
max. SW 30 mm
general informationThe design ensures a defined fail-to-safe position – open or closed – in case of control powerfailure. They are very economic and reliable safe, because the BESI HSTP has:
• second independent piston for emergency operation• quick connection for emergency hand pump• visual position indication• just one connection pipe
BESI ArmaturenBremen
HSTP 78 – 63 / Fhydraulic spring return actuator 90°
detail list
BESI Armaturen GmbH & Co KG Phone: +049 (0) 421 57 64 3 – 0; Fax: +049 (0) 421 58 36 21; eMail: [email protected]
The reproduction, transmission or use of this document or its contens is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights eratedby patent grant or registration of a utility model for design are reserved. Modification without notice. 1102_HSTP78-63F-2 - edition: 11.09.2000
item object material pce.1 body GG25 12 upper cover C45 14 pinion shaft St 52.3 15 pinion St 52.3 16 rack C45 17 piston C45 18 piston C45 19 cylinder St 52.3 1
10 spring cylinder St52 111 cover C45k 112 flange C45k 113 locating plug C45 114 cover C45k 115 cup nut 1.4305 116 hexagon nut 1.4305 117 tie rod 9S20k 420 plate spring spring St 3421 o-ring NBR 122 o-ring NBR 123 o-ring NBR 124 o-ring NBR 625 o-ring NBR 226 o-ring NBR 227 o-ring NBR 228 o-ring NBR 129 o-ring NBR 232 piston sealing NBR 133 rod sealing NBR 135 piston ring Polyamid PA 136 piston ring Polyamid PA 139 oil level glass PA 140 plug Ku 145 hexagon screw 8.8galZn 146 hexagon screw 8.8galZn 447 screw 8.8galZn 648 screw 8.8galZn 649 screw 8.8galZn 150 hexagon nut 8.8 verz. 451 screwing St 152 quick coupling EMA3/R1/4“ St galZn 1
BESI ArmaturenBremen
HST2P 78 – 60 / Fhydraulic spring return actuator 90°
BESI Armaturen GmbH & Co KG Phone: +049 (0) 421 57 64 3 – 0; Fax: +049 (0) 421 58 36 21; eMail: [email protected]
The reproduction, transmission or use of this document or its contens is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights erated bypatent grant or registration of a utility model for design are reserved. Modification without notice. 1103_HST2P78-60F-1 - edition: 11.09.2000
main data standard / on request
function spring closed / openedinstallation dry / submerged / open deckmounting direction cross / parallel to pipelineoperation connection = PA OD 8mm / OD 10 mmcoating alkyd resin primer
synthetic resin finishmax. working pressure 135 bartotal dry weight 56 kgoil displacement 320 cm³temperature range -20° - +80°Crotation 90° ±2°
options• electr. limit switch – IP65 / IP68 / EEx• potentiometer• direct mounted electro hydraulic power
pack (EHPP), controled by one cable• manual worm gear• separate control block• special connections• special coating
hydraulic viscosities 15 – 46 cSt./40°Ctorque 650 Nm by springflange dimension ISO 5211 - F 12 = ø125-4xM12
ISO 5211 - F 14 = ø140-4xM16ISO 5211 - F 16 = ø165-4xM20
valve shaft dimensions
max. SW 30 mm
max. ø 35 mm acc. DIN 6885
max. SW 30 mm
general informationThe design ensures a defined fail-to-safe position – open or closed – in case of control powerfailure. They are very economic and reliable safe, because the BESI HSTP has:
• quick connection for emergency hand pump• visual position indication• just one connection pipe
BESI ArmaturenBremen
HST2P 78 – 60 / Fhydraulic spring return actuator 90°
detail list
BESI Armaturen GmbH & Co KG Phone: +049 (0) 421 57 64 3 – 0; Fax: +049 (0) 421 58 36 21; eMail: [email protected]
The reproduction, transmission or use of this document or its contens is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights eratedby patent grant or registration of a utility model for design are reserved. Modification without notice. 1103_HST2P78-60F-2 - edition: 11.09.2000
item object material pce.1 body GG25 1,0002 body cover C45 1,0004 pinion shaft St52.3 1,0005 pinion St52.3 1,0006 rack C45 2,0007 piston C45 2,0008 adaptor C45 2,00010 spring body St52-3 2,00011 guide bush POM 2,00015 slide ring POM 2,00019 lift stoper 8.8 galZn 2,00020 hexagon nut 8.8 verz. 2,00021 o-ring NBR 2,00022 o-ring NBR 2,00023 o-ring NBR 4,00027 o-ring NBR 2,00028 groove ring NBR 2,00029 o-ring NBR 2,00031 hexagon screw 8.8galZn 6,00033 hexagon nut 1.4305 1,00034 cup nut 1.4305 1,00035 grub screw St45H 1,00039 hexagon screw 8.8galZn 8,00041 oil level glass PA 1,00042 plug Ku 1,00046 disc spring spring St 37,00051 globe valve St 1,00052 screwing St 1,00053 straight pipe screwing St 1,00054 screwing St 1,00055 quick coupling EMA3/R1/4“ St-verzinkt 1,00056 cap nut St 1,000
BESI ArmaturenBremen
HSTP 108 – 90 / Fhydraulic spring return actuator 90°
BESI Armaturen GmbH & Co KG Phone: +049 (0) 421 57 64 3 – 0; Fax: +049 (0) 421 58 36 21; eMail: [email protected]
The reproduction, transmission or use of this document or its contens is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights erated bypatent grant or registration of a utility model for design are reserved. Modification without notice. 1114_HSTP108-90F-1 - edition: 16.09.2003
main data standard / on request
function spring closed / openedinstallation dry / submerged / open deckmounting direction cross / parallel to pipelineoperation connection = PA OD 8mm / OD 10 mmcoating alkyd resin primer
synthetic resin finishworking pressure 100 bar (max. 135 bar)approx. dry weight kgoil displacement 516 cm³temperature range -20° - +80°Crotation 90° ±2°
options• electr. limit switch – IP65 / IP68 / EEx• potentiometer• direct mounted electro hydraulic power
pack (EHPP), controlled by one cable• manual declutchable worm gear• special connections• special coating
hydraulic viscosity 15 – 46 cSt./40°Ctorque 1100 Nm by springflange dimensions ISO 5211 - F 12 = ø125-4xM12
ISO 5211 - F 14 = ø140-4xM16valve shaft dimensions
max. SW 40 mm
max. ø 50 mm acc. DIN 6885
max. SW 40 mm
general informationThe design ensures a defined fail-to-safe position – open or closed – in case of control powerfailure. Very economic and reliable safe, with:
• second independent piston for emergency operation• quick connection for emergency hand pump (PN)• visual position indication• just one control pipe
BESI ArmaturenBremen
HSTP 108 – 90 / Fhydraulic spring return actuator 90°
detail list
BESI Armaturen GmbH & Co KG Phone: +049 (0) 421 57 64 3 – 0; Fax: +049 (0) 421 58 36 21; eMail: [email protected]
The reproduction, transmission or use of this document or its contens is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights eratedby patent grant or registration of a utility model for design are reserved. Modification without notice. 1114_HSTP108-90F-2 - edition: 16.09.2003
item object material pce.1 body GG25 12 upper body C45 14 pinion shaft St 52.3 15 pinion St 52.3 16 rack C45 17 piston C45 18 piston C45 19 cylinder St 52 1
10 spring cylinder St 52 111 cover C45 112 flange C45 113 locating plug C45 114 cover C45 115 cup nut 1.4305 116 hexagon nut 1.4305 117 tie rod 9S20k 620 plate spring St 4221 o-ring NBR70 122 o-ring NBR70 123 o-ring NBR70 124 o-ring NBR70 625 o-ring NBR70 226 o-ring NBR70 227 o-ring NBR70 228 o-ring NBR70 129 o-ring NBR70 231 piston sealing NBR 132 piston sealing NBR 135 piston ring PTFEB 500 136 piston rin PTFEB 500 139 oil level glass PA 140 plug Ku 143 hexagon screw 8.8galZn. 144 hexagon screw 8.8galZn. 145 screw 8.8galZn 146 screw 8.8galZn 347 screw 8.8galZn 648 hexagon screw 8.8galZn 649 grub screw St45H 150 hexagon nut 8.8v erz. 651 screwing St 152 quick connector steel St verzink 1
BESI ArmaturenBremen
HSTP 156 – 100 / Fhydraulic spring return actuator 90°
BESI Armaturen GmbH & Co KG Phone: +049 (0) 421 57 64 3 – 0; Fax: +049 (0) 421 58 36 21; eMail: [email protected]
The reproduction, transmission or use of this document or its contens is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights erated bypatent grant or registration of a utility model for design are reserved. Modification without notice. 1104_HSTP156-100F-1 - edition: 11.09.2000
main data standard / on request
function spring closed / openedinstallation dry / submerged / open deckmounting direction cross / parallel to pipelineoperation connection = PA OD 8mm / OD 10 mmcoating alkyd resin primer
synthetic resin finishmax. working pressure 135 bartotal dry weight kgoil displacement 925 cm³temperature range -20° - +80°Crotation 90° ±2°
options• electr. limit switch – IP65 / IP68 / EEx• potentiometer• direct mounted electro hydraulic power
pack (EHPP), controlled by one cable• manual declutchable worm gear• separate control block• special connections• special coating
hydraulic viscosities 15 – 46 cSt./40°Ctorque 2025 Nm by springflange dimension ISO 5211 - F 12 = ø125-4xM12
ISO 5211 - F 14 = ø140-4xM16valve shaft dimensions
max. SW 40 mm
max. ø 50 mm acc. DIN 6885
max. SW 40 mm
general informationThe design ensures a defined fail-to-safe position – open or closed – in case of control powerfailure. They are very economic and reliable safe, because the BESI HSTP has:
• second independent piston for emergency operation• quick connection for emergency hand pump• visual position indication• just one connection pipe
BESI ArmaturenBremen
HSTP 156 – 100 / Fhydraulic spring return actuator 90°
detail list
BESI Armaturen GmbH & Co KG Phone: +049 (0) 421 57 64 3 – 0; Fax: +049 (0) 421 58 36 21; eMail: [email protected]
The reproduction, transmission or use of this document or its contens is not permitted without express written authority. Offenders will be liable for damages. All rights, including rights eratedby patent grant or registration of a utility model for design are reserved. Modification without notice. 1104_HSTP156-100F-2 - edition: 11.09.2000
item object material pce.1 body GG25 1,0002 upper cover C45 1,0004 pinion shaft St 52.3 1,0005 pinion St 52.3 1,0006 rack C45 1,0007 piston C45 1,0008 piston C45 1,0009 cylinder St 52 1,000
10 spring cylinder St52 1,00011 cover C45 1,00012 flange C45 1,00013 locating plug C45 1,00014 cover C45 1,00015 cup nut 1.4305 1,00016 hexagon nut 1.4305 1,00017 tie rod 9S20k 6,00020 disc spring spring St 46,00021 o-ring NBR 1,00022 o-ring NBR 1,00023 o-ring NBR 1,00024 o-ring NBR 6,00025 o-ring NBR 2,00026 o-ring NBR 2,00027 o-ring NBR 2,00028 o-ring NBR 1,00029 o-ring NBR 2,00031 piston sealing NBR 1,00032 piston sealing NBR 1,00035 piston ring PTFE B500 1,00036 piston ring PTFE B500 1,00039 oil level glass PA 1,00040 plug Ku 1,00043 hexagon screw 10.9 1,00044 hexagon screw 10.9 1,00045 hexagon screw 8.8galZn 1,00046 hexagon screw 8.8galZn 3,00047 screw 8.8galZn 6,00048 hexagon screw 8.8galZn 8,00049 grub screw St45H 1,00050 hexagon nut 8.8 verz. 12,00051 screwing St 1,00052 quick connection EMA3/R1/4“ St-verzinkt 1,000
