Bell and Spigot Pipe Joint

Foundry Operations

DurironBell andSpigotPipe andFittings

Price Sheet 7-21Bulletin PF-9

Foundry Operations

DurironBell & SpigotPiping

Applications

For over 85 years Duriron Bell & Spigot piping has been providing a durable andreliable means to transport corrosive chemicals safely. Installed using traditional plumbing techniques, Duriron Bell & Spigot pipe requires little maintenance and oftenoutlasts the life of the building or system in which it is used.

Duriron Bell & Spigot pipe and fittings provide a myriad of advantages other corrosion resistant piping do not. Among these are the following:

• Nearly universal corrosion resistance • Safe to use in return air plemuns• Safe above and below ground • Fire and smoke proof• Longevity – Life of the building installation • No intumescent firestops• Can be mechanically or chemically cleaned • Outstanding abrasion resistance• Suitable to 500°F (260°C) • Solids will not cling to the walls

Anywhere you find acids, solvents, bleaches, detergents, or other aggressive fluids,Duriron pipe and fittings can be used. Duriron pipe is the best-engineered solution forhandling traditional acid waste services, such as those found in hospitals, research labo-ratories, and schools and universities. However, its unique characteristics also make itideally suited for many applications not normally deemed “acid waste.” One such non-traditional application is correctional facilities, where Duriron’s resistance to chlorinecleaning chemicals in combination with its ability to be mechanically cleaned make it along lasting alternative to cast iron. Additionally, Duriron’s outstanding corrosion resist-ance lends itself to use in commercial or institutional kitchens and concessions, wherehighly acidic food waste, sodas, and cleaning chemicals are present.

Duriron Bell & Spigot pipe and fittings are intended for use in gravity fed applications.They are not designed for use under pressure.

Following is a partial list of applications for which Duriron pipe is ideally suited.

• LaboratoriesSchoolsForensicCommercial/industrial

• Food & BeverageInstitutional kitchensFast-food restaurantsSoda fountainsBeverage plantsDairiesConfectioners

• Pharmaceutical PlantsProcess waste

2

• Medical FacilitiesHospitalsDialysis centers

• Correctional Facilities• Commercial Operations

Printing plantsPlating processesBattery stationsPaint/lacquer plants

• Film ProcessingPhotofinishing labsFilm plants

• Waste Water Treatment

Foundry Operations

Installation ofDuriron Bell & SpigotPiping

Method of InstallationDuriron Bell & Spigot pipe is installed using traditional plumbing methods and is in

accordance with all city and state plumbing codes.A Duriron Bell & Spigot pipe joint is made using conventional plumbing tools, virgin

lead, and special acid-resistant rope packing, called Red Stripe Sealite No. 312A. Tomake a joint, cut several segments of Sealite rope packing long enough to encircle thespigot (plain) end of the pipe and overlap approximately two inches.

Insert the spigot end of a pipe into the bell of the adjoining pipe, leaving a slightspace (A) between the two lengths of pipe to avoid metal-to-metal contact and theresulting stress caused by the thermal expansion of the pipe. Using the blunt end of ayarning iron, firmly insert each segment of rope packing into the bell (C). The annularspacing between different pipes and fittings may vary. If the packing is difficult to insertinitially, slightly flatten the rope packing with a hammer prior to insertion. A sufficientnumber of segments (generally three) shall be inserted such that the bell is approxi-mately half full. To avoid a leak path, alternate by 90° the position where each segmentof Sealite rope packing overlaps. Do not continually wrap a single segment of Sealiterope packing as this type of installation provides a continuous leak path along the rope.

Using virgin lead heated just to the melting point, pour a sufficient amount of leadover the rope packing, completely filling the hub (B). Do not overheat the lead. The leadis too hot if it is a cherry red color. After the lead has solidified, lightly caulk the joint,taking care not to strike the pipe. If the pipe or fitting is cold, SLOWLY warm the twoends to be joined prior to pouring the lead. Flowserve Corporation does not recommendusing a torch to warm the pipe as doing so may thermally shock the material, causingthe pipe to crack.

Red Stripe Sealite Rope PackingSealite is an asbestos free, acid resistant rope packing that is specially designed for

use with Duriron Bell & Spigot pipe and fittings. Made of highly corrosion resistantmaterials, Sealite rope packing seals the Duriron Bell & Spigot pipe joints by absorbinglarge quantities of the service fluid, expanding to several times it original volume. It isthe packing that seals the joint, not the lead.

Due to the aggressive environments in which Duriron Bell & Spigot piping isinstalled, it is essential that only Sealite rope packing be used. Hemp, oakum, and dryasbestos packing will not provide long lasting, leak proof joints.

Sealite rope packing is manufactured with a moisture content of 8-10% to make itsoft and pliable for installation. It should feel “damp.” To retain the necessary character-istics of Sealite rope packing, it is imperative the poly bag in which the Sealite is pack-aged not be left open for long periods of time. A wet sponge placed inside the bag willaid in keeping the rope at the optimum moisture content. Do not use excessively wet orfrozen Sealite rope packing as doing so may cause the molten lead to sputter and spit.Thaw frozen Sealite rope packing before use. If the packing is too wet, allow the excessmoisture to evaporate before use.

HangingIn a horizontal run of pipe, Flowserve recommends supporting each length of

Duriron Bell & Spigot pipe by a hanger. If the line consists in part of fittings, supportsmust be placed no further than seven feet apart. P-Traps must be supported individually.Supports must be placed directly beneath horizontal fittings that connect to the stack.Supports should not clasp the pipe so tightly as to prevent normal lateral movement dueto expansion. Vertical lines of pipe must be supported at intervals not to exceed fourteenfeet. Hangers may be any type and do not have to be padded.

3

Foundry Operations

4

TestingDuriron Bell & Spigot piping should be tested in accordance with local plumbing

codes. A head of 7-10 feet is sufficient since the Duriron piping is gravity fed. Prior totesting Flowserve recommends filling the pipe with water and waiting 24 hours to allowthe Sealite rope packing to absorb the fluid and sufficiently expand to seal the joint.

CuttingDue to its hardness, Duriron high silicon iron cannot be cut with a blade. Instead,

Duriron can be cut in the field using a “chain” or “snap” cutter, either manual orhydraulic. These devices are made by such companies as Beaver, Reed, Ridgid,Springload, and Wheeler and do an excellent job of cutting high silicon iron. Using achain or snap cutter, Duriron can be cut as quickly and as easily as cast iron. Field cutpipe requires no additional work to be installed.

Burying Underground or in ConcreteDuriron piping may be buried underground or set in concrete. No special precau-

tions need to be observed and the pipe does not have to be coated. The first few inchesof fill should be rock free.

Fire Safety (Return Air Plenums)Duriron Bell & Spigot pipe and fittings do not burn or emit smoke. Consequently, it

is safe and in accordance with fire regulations to use Duriron Bell & Spigot piping inreturn air plenums. No intumescent firestops are required in a Duriron installation.

Installation for Hot ServicesAllowance for expansion is particularly important if very hot solutions are to be

dumped into a Duriron drainage system. The shock of such applications may be violentwhen pipe lines are only partially full of hot liquids. In services where the temperaturevariations are unusual or the pipe lines extremely long, expansion joints or invertedtraps are used to alleviate the problem. Common applications where such conditionsexist include metal plating, pickling, and those with hot rinse tanks.

PaintingDuriron high silicon iron pipe and fittings may be painted. There is no coating to be

removed or special preparation required.

CleaningDuriron Bell & Spigot piping may be cleaned using a mechanical sewer auger or

chemicals without fear of damaging the pipe or joint.

Duriron is a high silicon iron alloy that is resistant to practically all commonly usedprocess chemicals and is recognized by architects, engineers, and plumbing contractorsthroughout the country as the superior material for handling acid waste.

Duriron conforms to ASTM specifications A518 and A861 and is approved by allplumbing codes. It obtains its outstanding corrosion resistance from the 14.5% siliconpresent in its composition. Duriron has unexcelled resistance to sulfuric, nitric,hydrochloric, and acetic acids. It is resistant to both oxidizing and reducing solutionsand is not appreciably affected by either concentration or temperature. Duriron also isextremely abrasion and erosion resistant. Furthermore, Duriron pipe and fittings are castwith solid wall sections, meaning abrasion and corrosion resistance are not dependentupon a thin lining or coating, but are consistent throughout the wall thickness.

Installation ofDuriron Bell & SpigotPipingCont’d

DurironHigh Silicon Iron

Foundry Operations

5

While the strength of Duriron is considerably greater than that of almost all non-metallic piping, the tensile strength of this material is less than most metals, includingnormal cast iron. Consequently, during handling caution should be exercised not to subject the pipe to undue mechanical stress or thermal shock.

Flowserve Corporation warrants all pipe, fittings, and accessories of its manufactureto be free from defects in material and workmanship. If any failure results from suchcases within ten years after purchase, Flowserve Corporation will, after inspection by afactory representative, supply replacement parts at no charge to the customer. The lia-bility of Flowserve Corporation is expressly limited to supplying such replacement parts.

Returned MaterialThe following conditions apply to the return of Duriron pipe and fittings. Credit, where

applicable, will be issued approximately 60 days from the date of receipt of the returneditems. Any questions regarding the return goods policy should be directed to theFlowserve Corporation, manufacturer of Duriron pipe and fittings, or your local Durironrepresentative.

• Request for return authorization must be submitted to Flowserve Corporation or itsrepresentatives in writing. Such request must state the reason(s) for the return andreference the order(s) against which the material was purchased. FlowserveCorporation reserves the right to refuse return authorization on special make items,non-stocked items, or for any other reason. Flowserve Corporation also reserves theright to refuse the return of any list of material having a total list value less than$100.00.

• Items must be returned freight prepaid FOB destination, unless Flowserve Corporationinstructs otherwise.

• The return authorization tag(s) must accompany the returned item(s).• Credit will be issued for items returned in saleable condition. Credit will not be given

for items that are used, broken, or otherwise damaged.• All returns are subject to a handling fee.• Credit for returned items will be applied to the customer’s account, unless notified in

writing to issue credit in the form of a check.

For additional details regarding the terms applying to the return of materials, pleasecontact Flowserve Corporation.

ShippingAll shipments are F.O.B. Dayton, Ohio. If export packing is necessary, please contact

Flowserve Corporation for pricing. In the event of transportation shortages or damages, it is the responsibility of the

customer to file any and all claims with the transportation company.

Warranty

Crushing Loads, lbs/ft (N/m)Duriron 15,700 (22,912)Borosilicate Glass 1,200 (1,751)Vitrified Tile 1,560 (2,277)

Material and Mechanical Properties of DurironDensity, lb/cu. in 0.255Hardness, Brinell 520Thermal Conductivity, cgs 0.125Tensile Strength (1/2 inch dia. bar), psi 20,000

Foundry Operations

Hub and Plain End Pipe

Straight Tees

Working OverallSize A B C D E F Wt. Length Lengthin Part No. in in in in in in lbs ft ft/in

(mm) (mm) (mm) (mm) (mm) (mm) (mm) (kg) (m) (mm)2 BS36414AA 49/16 43/16 35/16 21/32 211/16 25/8 62 7 7' 25/8"

(50) (116) (106) (84) (52) (68) (67) (28.1) (2.1) (2200)3 BS36415AA 55/16 53/16 45/16 31/8 325/32 25/8 90 7 7' 25/8"

(80) (135) (132) (110) (79) (96) (67) (40.8) (2.1) (2200)4 BS36416AA 63/8 63/16 55/16 41/8 425/32 25/8 114 7 7' 25/8"

(100) (162) (157) (135) (105) (121) (67) (51.7) (2.1) (2200)6 BS36291AA 817/32 811/32 75/16 515/16 611/16 3 169 7 7' 25/8"

(150) (217) (212) (186) (151) (170) (76) (76.7) (2.1) (2200)8 BS36290AA 111/4 103/4 95/8 81/4 9 3 234 7 7' 25/8"

(200) (286) (273) (244) (210) (229) (76) (106.1) (2.1) (2200)10 D5650 141/4 133/4 121/4 10 111/4 37/8 340 5 5' 35/8"

(250) (362) (349) (311) (254) (286) (98) (154) (1.5) (1616)12 D6500 163/4 16 141/2 12 131/4 4 470 5 5' 4"

(300) (425) (406) (368) (305) (337) (102) (213) (1.5) (1626)15 D6550 201/4 193/4 173/4 15 163/4 41/8 800 5 5' 41/8"

(380) (514) (502) (451) (381) (425) (105) (363) (1.5) (1629)

Sanitary TBranches

Sanitary YBranches

Size Wt. A B Cin Part No. lbs in in in

(mm) (kg) (mm) (mm) (mm)2x11/2 K1672-1.5 11 81/2 17/8 65/8

(50x40) (5.0) (216) (48) (168)2x2 K1672 12 9 2 7

(50x50) (5.4) (229) (51) (178)3x2 K3892-2 17 9 21/2 613/16

(80x50) (7.7) (229) (64) (173)3x3 K3892 19 10 21/2 71/2

(80x80) (8.6) (254) (64) (190)4x2 K3893-2 20 9 3 7

(100x50) (8.1) (229) (76) (178)4x3 K3893-3 221/2 10 3 71/4

(100x80) (10.2) (254) (76) (184)4x4 K3893 26 11 3 8

(100x100) (11.8) (279) (76) (203)


(mm) (kg) (mm) (mm) (mm)2x11/2 D5027-1.5 11 81/2 31/2 63/4

(50x40) (5.0) (216) (89) (171)2x2 D5027 12 9 31/2 7

(50x50) (5.4) (229) (89) (178)3x11/2 D5052-1.5 16 81/2 4 63/4

(80x40) (7.3) (216) (102) (171)3x2 D5052-2 18 9 4 7

(80x50) (8.2) (229) (102) (178)3x3 D5052 20 10 4 71/2

(80x80) (9.1) (254) (102) (190)4x11/2 D5077-1.5 18 81/2 41/2 63/4

(100x40) (8.2) (216) (114) (171)4x2 D5077-2 19 9 41/2 7

(100x50) (8.6) (229) (114) (178)4x3 D5077-3 26 10 41/2 71/2

(100x80) (11.8) (254) (114) (190)4x4 D5077 28 11 41/2 8

(100x100) (12.7) (279) (114) (203)6x2 D5127A2 31 9 51/2 7

(150x50) (14.1) (229) (140) (178)6x3 D5127A3 33 10 51/2 71/2

(150x80) (15.0) (254) (140) (190)6x4 D5127A4 35 11 51/2 8

(150x100) (15.9) (279) (140) (203)6x6 D5127A 50 13 51/2 9

(150x150) (22.7) (330) (140) (229)8x4 D5603-4 62 105/8 61/4 8

(200x100) (28.1) (270) (159) (203)8x6 D5603-6 65 141/2 65/8 101/2

(200x150) (29.5) (368) (168) (267)8x8 D5603 113 19 65/8 131/2

(200x200) (51.3) (483) (168) (343)10x6 D6702-6 130 141/4 75/8 101/2

(250x150) (59.0) (362) (194) (267)10x10 D6702 180 21 73/4 141/2

(250x250) (81.7) (533) (197) (368)12x8 D6502-8 187 19 83/4 131/2

(300x200) (84.9) (483) (222) (343)


(mm) (kg) (mm) (mm) (mm)2x11/2 D5026-1.5 11 85/8 43/8 43/8

(50x40) (5.0) (219) (111) (111)2x2 D5026 12 9 41/4 43/4

(50x50) (5.4) (229) (108) (121)3x11/2 D5051-1.5 16 85/8 51/16 37/8

(80x40) (7.3) (219) (129) (98)3x2 D5051-2 17 9 5 43/16

(80x50) (7.7) (229) (127) (106)3x3 D5051 21 101/2 51/2 5

(80x80) (9.5) (267) (140) (127)4x11/2 D5076-1.5 17 91/8 513/16 37/8

(100x40) (7.7) (232) (148) (98)4x2 D5076-2 21 9 53/4 311/16

(100x50) (9.5) (229) (146) (94)4x3 D5076-3 26 101/2 61/4 41/2

(100x80) (11.8) (267) (159) (114)4x4 D5076 30 12 63/4 51/4

(100x100) (13.6) (305) (171) (133)6x2 D5126A2 28 9 71/8 211/16

(150x50) (12.7) (229) (181) (68)6x3 D5126A3 35 101/2 75/8 31/2

(150x80) (15.9) (267) (194) (89)6x4 D5126A4 45 121/4 81/4 41/4

(150x100) (20.4) (311) (210) (108)6x6 D5126A 60 143/4 91/8 53/4

(150x150) (27.2) (375) (232) (146)8x2 D5602-2 60 167/8 9 41/2

(200x50) (27.2) (429) (229) (114)8x3 D5602-3 63 121/8 9 33/4

(200x80) (28.6) (308) (229) (95)8x4 D5602-4 65 131/2 10 41/2

(200x100) (29.5) (343) (254) (114)8x6 D5602-6 79 161/2 11 61/16

(200x150) (35.9) (419) (279) (154)8x8 D5602 117 191/2 121/4 71/4

(200x200) (53.1) (495) (311) (184)10x4 D5655-4 160 131/2 111/2 31/2

(250x100) (72.6) (343) (292) (89)10x6 D5655-6 165 165/8 131/2 37/8

(250x150) (74.9) (422) (343) (98)10x8 D5655-8 170 193/4 143/8 43/8

(250x200) (77.2) (502) (365) (111)10x10 D5655 180 221/2 15 75/8

(250x250) (81.7) (572) (381) (194)12x4 CS12196B 173 181/4 153/16 41/2

(300x100) (78.5) (464) (386) (114)12x6 CS12196A 196 181/4 161/2 41/2

(300x150) (89.0) (464) (419) (114)12x8 D6501-8 200 233/8 151/2 5

(300x200) (90.8) (594) (394) (127)12x10 D6501-10 275 27 191/2 6

(300x250) (125) (686) (495) (152)12x12 D6501 288 251/2 183/8 71/4

(300x300) (131) (648) (467) (184)15x15 D6551 455 321/8 223/4 81/8

(380x380) (207) (816) (578) (206)6

Foundry Operations

Double BranchSanitary Y

Double Branch SanitaryCombination Y and 1/8 Bend (T-Y)

Sanitary Combination Y and 1/8 Bend (T-Y)

Double BranchSanitary Tee


(mm) (kg) (mm) (mm) (mm)2x11/2 D5027DB1.5 14 81/2 7 63/4

(50x40) (6.4) (216) (178) (171)2x2 D5027DB 16 9 7 7

(50x50) (7.3) (229) (178) (178)3x11/2 D5052DB1.5 15 81/2 8 63/4

(80x40) (6.8) (216) (203) (171)3x2 D5052DB2 17 9 8 7

(80x50) (7.7) (229) (203) (178)3x3 D5052DB 22 10 8 71/2

(80x80) (10.0) (254) (203) (190)4x11/2 D5077DB1.5 18 81/2 9 63/4

(100x40) (8.2) (216) (229) (171)4x2 D5077DB2 21 9 9 7

(100x50) (9.5) (229) (229) (178)4x3 D5077DB3 24 10 9 71/2

(100x80) (10.9) (254) (229) (190)4x4 D5077DB 37 11 9 8

(100x100) (16.8) (279) (229) (203)6x3 D5127ADB3 50 10 11 71/2

(150x80) (22.7) (254) (279) (190)6x4 D5127ADB4 46 11 11 8

(150x100) (20.9) (279) (279) (203)6x6 D5127ADB 58 13 11 9

(150x150) (26.3) (330) (279) (229)8x6 D5603DB6 80 141/2 131/4 101/2

(200x150) (36.3) (368) (337) (267)8x8 D5603DB 113 19 65/8 131/2

(200x200) (51.3) (483) (168) (343)


(mm) (kg) (mm) (mm) (mm)2x11/2 D5026DB1.5 14 85/8 43/8 43/8

(50x40) (6.4) (219) (111) (111)2x2 D5026DB 15 9 41/4 43/4

(50x50) (6.8) (229) (108) (121)3x11/2 D5051DB1.5 19 85/8 51/16 37/8

(80x40) (8.6) (219) (129) (98)3x2 D5051DB2 20 9 5 43/16

(80x50) (9.1) (229) (127) (106)3x3 D5051DB 28 101/2 51/2 5

(80x80) (12.7) (267) (140) (127)4x11/2 D5076DB1.5 21 91/8 513/16 37/8

(100x40) (9.5) (232) (148) (98)4x2 D5076DB2 23 9 53/4 311/16

(100x50) (10.4) (229) (146) (94)4x3 D5076DB3 26 101/2 61/4 41/2

(100x80) (11.8) (267) (159) (114)4x4 D5076DB 33 12 63/4 51/4

(100x100) (15.0) (305) (171) (133)6x2 D5126ADB2 31 9 71/8 211/16

(150x50) (14.1) (229) (181) (68)6x3 D5126ADB3 46 101/2 75/8 31/2

(150x80) (20.9) (267) (194) (89)6x4 D5126ADB4 52 12 81/8 41/4

(150x100) (23.6) (305) (206) (108)6x6 D5126ADB 65 143/4 91/8 53/4

(150x150) (29.5) (360) (232) (146)8x4 D5602DB4 71 131/2 10 101/2

(200x100) (32.2) (343) (254) (267)8x6 D5602DB6 86 161/2 11 61/16

(200x150) (39.0) (419) (279) (154)

Size Wt. A B C Ein Part No. lbs in in in in

(mm) (kg) (mm) (mm) (mm) (mm)2x11/2 D5028DB1.5 15 85/8 91/4 43/8 73/8

(50x40) (6.8) (219) (235) (111) (187)2x2 D5028DB 17 9 101/2 43/4 81/4

(50x50) (7.7) (229) (267) (121) (210)3x11/2 D5053DB1.5 17 85/8 101/4 37/8 73/8

(80x40) (7.7) (219) (260) (98) (187)3x2 D5053DB2 22 9 111/2 43/16 83/16

(80x50) (10.0) (229) (291) (106) (208)3x3 D5053DB 27 101/2 13 5 99/16

(80x80) (12.3) (267) (330) (127) (243)4x11/2 D5078DB1.5 24 91/8 113/4 37/8 81/8

(100x40) (10.9) (232) (298) (98) (206)4x2 D5078DB2 24 9 121/2 311/16 83/16

(100x50) (10.9) (229) (318) (94) (208)4x3 D5078DB3 28 101/2 14 41/2 99/16

(100x80) (12.7) (267) (356) (114) (243)4x4 D5078DB 40 12 151/2 51/4 1013/16

(100x100) (18.2) (305) (394) (133) (275)6x3 D5128ADB3 45 101/2 16 31/2 99/16

(150x80) (20.4) (267) (406) (89) (243)6x4 D5128BDB4 57 12 171/2 41/4 1013/16

(150x100) (25.9) (305) (444) (108) (275)6x6 D5128AADB 83 15 201/2 53/4 137/16

(150x150) (37.7) (381) (521) (146) (341)

Size Wt. A B C Ein Part No. lbs in in in in

(mm) (kg) (mm) (mm) (mm) (mm)2x11/2 D5028-1.5 11 85/8 45/8 43/8 73/8

(50x40) (5.0) (219) (117) (111) (187)2x2 D5028 13 9 51/4 43/4 81/4

(50x50) (5.9) (229) (133) (121) (210)3x11/2 D5053-1.5 14 85/8 51/8 37/8 73/8

(80x40) (6.4) (219) (130) (98) (187)3x2 D5053-2 18 9 53/4 43/16 83/16

(80x50) (8.2) (229) (146) (106) (208)3x3 D5053 24 101/2 61/2 5 99/16

(80x80) (10.9) (267) (165) (127) (243)4x11/2 D5078-1.5 17 91/8 57/8 37/8 81/8

(100x40) (7.7) (232) (149) (98) (206)4x2 D5078-2 21 9 61/4 311/16 83/16

(100x50) (9.5) (229) (159) (94) (208)4x3 D5078-3 23 101/2 7 41/2 99/16

(100x80) (10.4) (267) (178) (114) (243)4x4 D5078 31 12 73/4 51/4 1013/16

(100x100) (14.1) (305) (197) (133) (275)6x2 D5128A2 33 9 71/4 211/16 83/16

(150x50) (15.0) (229) (184) (68) (208)6x3 D5128A3 37 101/2 8 31/2 99/16

(150x80) (16.8) (267) (203) (89) (243)6x4 D5128B4 47 12 83/4 41/4 1013/16

(150x100) (21.3) (305) (222) (108) (275)6x6 D5128AA 63 15 101/4 53/4 137/16

(150x150) (28.6) (381) (260) (146) (341)10x6 D6703-6 185 163/4 121/2 47/16 43/8

(250x150) (83.9) (425) (318) (113) (365)10x8 D6700-8 192 213/8 151/8 61/2 181/2

(250x200) (87.2) (543) (384) (165) (470) 7

Sanitary Increasers Hub Strainers

Eighth Bends Sixteenth Bends

Quarter Bends Sixth Bends

Long SweepQuarter Bends

Foundry Operations

Short Sweep Quarter Bends

8

Size Wt. B Cin Part No. lbs in in

(mm) (kg) (mm) (mm)2 BS15899A 11 51/4 8

(50) (5.0) (133) (203)3 WS15900A 20 6 9

(80) (9.1) (152) (229)4 WS15901A 25 61/2 10

(100) (11.4) (165) (254)


(mm) (kg) (mm) (mm)2 WS5044A 14 81/2 12

(50) (6.4) (216) (305)3 WS5069A 24 9 121/2

(80) (10.9) (229) (318)4 D5094A 29 91/2 13

(100) (13.2) (241) (330)6 D5143AA 47 101/2 14

(150) (21.3) (267) (356)8 D5618A 98 111/8 15

(200) (44.5) (283) (381)


(mm) (kg) (mm) (mm)2 D5031 9 31/2 7

(50) (4.1) (89) (178)3 D5056 16 4 71/2

(80) (7.3) (102) (190)4 D5081 20 41/2 8

(100) (9.1) (114) (203)6 WS5131C 36 51/2 9

(150) (16.3) (140) (229)8 D5606 54 61/8 10

(200) (24.5) (156) (254)10 D6706 116 85/8 12

(250) (52.7) (219) (305)12 D6506 195 103/8 14

(300) (88.5) (264) (356)


(mm) (kg) (mm) (mm)2 D5032 7 13/4 51/4

(50) (3.2) (44) (133)3 D5057 13 115/16 57/16

(80) (5.9) (49) (138)4 D5082 16 23/16 511/16

(100) (7.3) (56) (144)6 D5132A 25 29/16 61/16

(150) (11.4) (65) (154)8 D5607 46 311/16 813/16

(200) (20.9) (94) (224)10 D5657 95 41/4 91/4

(250) (43.1) (108) (235)12 D6507 132 5 95/8

(300) (59.9) (127) (244)


(mm) (kg) (mm) (mm)2 D5041 6 11/8 45/8

(50) (2.7) (29) (117)3 D5066 8 13/16 411/16

(80) (3.6) (30) (119)4 D5091 11 15/16 413/16

(100) (5.0) (33) (122)6 D5140A 21 11/2 5

(150) (9.5) (38) (127)8 D5615 44 21/16 71/8

(200) (20.0) (52) (181)10 S1245A 80 2 67/8

(250) (36.3) (51) (175)

Size Wt.in Part No. lbs

(mm) (kg)2 AS6288A 21/2

(50) (1.1)3 BS19643A 3

(80) (1.4)4 D1977AB 5

(100) (2.3)6 BS3366AA 10

(150) (4.5)8 BS3367AA 18

(200) (8.2)

Size Wt. Ain Part No. lbs in

(mm) (kg) (mm)2x3 D5037-3 9 9

(50x80) (4.10) (229)2x4 D5037-4 13 9

(50x100) (5.9) (229)2x6 D5037A6 17 9

(50x150) (7.7) (229)3x4 D5062-4 17 9

(80x100) (7.7) (229)3x6 D5062A6 16 9

(80x150) (7.3) (229)4x6 D5087A6 17 9

(100x150) (7.7) (229)4x8 D5087-8 33 115/8

(100x200) (15.0) (295)6x8 D8080-8 50 117/8

(150x200) (22.7) (302)8x10 D5612-10 85 16

(200x250) (38.6) (406)

SPIGOT BELL


(mm) (kg) (mm) (mm)2 D5046 8 21/4 53/4

(50) (3.6) (57) (146)3 D5071 11 21/2 6

(80) (5.0) (64) (152)4 D5096 15 23/16 65/16

(100) (6.8) (56) (160)6 D5145A 27 33/8 67/8

(150) (12.3) (86) (175)8 CS12194A 71 41/8 9

(200) (32.2) (105) (229)

Sanitary Reducers

Double Hubs

Combination Cleanout and Test Tees

Pipe Plugs

Cleanout Plugs

Adapter / Spigot* andSplit Flange

Foundry Operations

9

Size Wt. A Jin Part No. lbs in in

(mm) (kg) (mm) (mm)2 PH3615BA 5 53/4 6

(50) (2.3) (146) (152)3 PH3615CA 11 7 71/2

(80) (5.0) (178) (190)4 PH3615DA 12 8 9

(100) (5.4) (203) (229)6 PH3615F 22 91/2 11

(150) (10.0) (241) (279)8 PH3615G 44 103/4 131/2

(200) (20.0) (273) (343)

Adapter / Bell andSplit Flange

Size Wt. A Jin Part No. lbs in in

(mm) (kg) (mm) (mm)2 PH3612B 5 21/2 6

(50) (2.3) (64) (152)3 PH3612C 7 21/2 71/2

(80) (3.2) (64) (190)4 PH3612D 12 23/4 9

(100) (5.4) (70) (229)6 PH3612F 16 3 11

(150) (7.3) (76) (279)8 PH3612G 36 31/2 131/2

(200) (16.3) (89) (343)


(mm) (kg)2 D8006 2

(50) (0.9)3 D8007 3

(80) (1.4)4 D8008 5

(100) (2.3)6 D8009A 10

(150) (4.5)8 K2722 17

(200) (7.7)12 BS14120A 56

(300) (25.4)


(mm) (kg)2 SA2707AA00 31/2

(50) (1.6)3 SA2708AA00 61/2

(80) (3.0)4 SA2709AA00 11

(100) (5.0)6 SA2719AA00 14

(150) (6.4)8 SA2720AA00 26

(200) (11.8)10 SA2721AA00 39

(250) (17.7)


(mm) (kg) (mm)2 D5039 61/2 1

(50) (3.0) (25)3 D5064 9 1

(80) (4.1) (25)4 D5089 12 1

(100) (5.4) (25)6 D5138 18 1

(150) (8.2) (25)8 D5613 40 2

(200) (18.2) (51)10 D6714 82 2

(250) (37.2) (51)


(mm) (kg) (mm)2x11/2 D5036-1.5 5 5

(50x40) (2.3) (127)3x11/2 D5061-1.5 6 5

(80x40) (2.7) (127)3x2 D5061-2 7 5

(80x50) (3.2) (127)4x11/2 D5086-1.5 7 5

(100x40) (3.2) (127)4x2 D5086-2 9 5

(100x50) (4.1) (127)4x3 D5086-3 11 5

(100x80) (5.0) (127)6x2 D5136A2 12 5

(150x50) (5.4) (127)6x3 D5136A3 13 5

(150x80) (5.9) (127)6x4 D5136A4 14 5

(150x100) (6.4) (127)8x4 D5601-4 22 6

(200x100) (10.0) (152)8x6 D5601-6 25 6

(200x150) (11.4) (152)10x6 D6711-6 39 6

(250x150) (17.7) (152)10x8 D6711-8 51 6

(250x200) (23.2) (152)12x6 D6511-6 55 61/2

(300x150) (25.0) (165)12x8 D6511-8 65 6

(300x200) (29.5) (152)12x10 D6511-10 83 6

(300x250) (37.7) (152)15x6 D6561-6 79 6

(380x150) (35.9) (152)15x12 D6561-12 109 6

(380x300) (49.5) (152)

*A Duriron M.J. Coupling may beused on the spigot end in the 2,3 and 4" sizes.

Split Flange Bolt Circle, Size and Number of BoltHoles are to ANSI Class 150

Threads are cast, not pipe threads.Countersunk heads available at no extra cost.

Split Flange Bolt Circle, Size and Number of BoltHoles are to ANSI Class 150

Size Wt. A B C D E Fin Part No. lbs in in in in in in

(mm) (kg) (mm) (mm) (mm) (mm) (mm) (mm)2 SA3759AA00 12 21/2 9 313/16 35/8 31/16 27/8

(50) (5.4) (64) (229) (97) (92) (78) (73)3 SA3762AA00 22 27/8 10 5 45/8 41/4 313/16

(80) (10.0) (73) (254) (127) (117) (108) (97)4 SA3760AA00 29 39/16 11 57/16 55/8 41/2 413/16

(100) (13.2) (91) (279) (138) (143) (114) (122)

SPIGOT BELL

Sanitary P Traps

For caulking into a sanitary T. Tee should be ordered separately.

Insertable Joints Backwater Valves /Palmer Type

Foundry Operations

NOTE: Depth of seal on all traps is 21/2 inches. Sanitary P Traps with hub vent also available less cleanout.

10

Size Wt. A Bin Part lbs in in

(mm) No. (kg) (mm) (mm)2

D504511 73/4 61/2

(50) (5.0) (197) (165)3

D507017 83/8 73/8

(80) (7.7) (213) (187)4

D509521 91/8 77/8

(100) (9.5) (232) (200)6

D5144A37 91/8 77/8

(150) (16.8) (232) (200)

Sizein Part No.

(mm)3 SA2733AA00(80)4 SA2734AA00(100)6 SA2735AA00(150)8 SA2736AA00(200)

Size Wt. A B C D E G H Ventin Part No. lbs in in in in in in in in

(mm) (kg) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm)2 Without Vent 12

(50) SA2695AA00 (5.4)2 Hub Vent 16 11 3 61/4 41/2 21/4 313/16 15/8 2

(50) SA2701AA00 (7.3) (279) (76) (159) (114) (57) (97) (41) (51)2 Less Cleanout 12

(50) P5033D (5.4)3 Without Vent 25

(80) SA2696AA00 (11.4)3 Hub Vent 32 121/2 41/4 61/4 51/2 3 41/2 25/16 3


(80) P5058D (11.4)4 Without Vent 37

(100) SA2697AA00 (16.8)4 Hub Vent 45 14 51/2 7 61/2 31/4 53/16 3 4


(100) P5083D (16.8)6 Without Vent 68

(150) SA2699AA00 (30.9)6 Hub Vent 80 17 81/2 8 81/2 4 61/2 315/16 4


(150) P5133E (30.9)

Detailed Cross Section of Cleanout Size Dia. of Drain Ain in in

(mm) (mm) (mm)Under 6" 11/2 23/16

(150 mm and under) (38) (56)6" and over 21/4 29/16

(over 150 mm) (57) (65)DRAIN

GASKETS (Teflon and Koroseal)

DRAIN COVER

DRAIN CLAMP

WELD

Standard traps carried in stock are made withcleanouts, as illustrated.

Traps can be supplied without cleanouts, asshown (left) at same prices, but require longerfor delivery.

Foundry Operations

Sanitary S Traps

Sanitary Running Traps

NOTE: Single Hub Vent is located on the inlet side. Depth of seal on 8" and 10" traps is 3". All others 21/2".Available with and without cleanouts. Customer should indicate on order.

NOTE: Depth of seal on all traps is 21/2 inches. Available with and without cleanouts. Customer should indicate on order.

Size Wt. A B C D E F G H Ventin Part No. lbs in in in in in in in in in

(mm) (kg) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm)2 Without Vent 16

(50) SA2690AA00 (7.3) 91/4 3 8 41/2 33/4 43/4 313/16 15/8 22 Hub Vent 18 (235) (76) (203) (114) (95) (121) (97) (41) (51)

(50) SA2677AA00 (8.2)3 Without Vent 24

(80) SA2691AA00 (10.9) 101/2 41/4 10 51/2 41/4 61/4 41/2 25/16 33 Hub Vent 29 (267) (108) (254) (140) (108) (159) (114) (65) (76)


(100) SA2692AA00 (15.0) 111/4 51/2 12 61/2 41/4 7 53/16 3 44 Hub Vent 39 (286) (140) (305) (165) (108) (178) (132) (76) (102)


(150) SA2693AA00 (37.2) 14 81/2 16 81/2 5 9 61/2 315/16 46 Hub Vent 89 (356) (216) (406) (216) (127) (229) (165) (100) (102)

(150) SA2680AA00 (40.4)

Size Wt. A B D E F G H Ventin Part No. lbs in in in in in in in in

(mm) (kg) (mm) (mm) (mm) (mm) (mm) (mm) (mm) (mm)2 Without Vent 14

(50) SA2682AA00 (6.4)2 Single Hub Vent 16 131/2 21/2 41/2 21/2 51/4 85/16 15/8 2

(50) SA2662AA00 (7.3) (343) (64) (114) (64) (133) (211) (41) (51)2 Double Hub Vent 12


(80) SA2683AA00 (11.4)3 Single Hub Vent 32 151/2 3 51/2 31/4 61/4 10 25/16 3



(100) SA2684AA00 (16.8)4 Single Hub Vent 45 171/2 31/2 61/2 31/2 71/4 1111/16 3 4



(150) SA2686AA00 (30.9)6 Single Hub Vent 80 211/2 41/2 81/2 41/4 81/4 15 315/16 4



(200) SA2687AA00 (73.5)8 Single Hub Vent 165 267/8 51/2 11 37/8 12 187/16 51/4 6



(250) SA2688AA00 (150)10 Single Hub Vent 334 317/8 71/8 13 51/8 16 221/4 611/16 6

(250) SA2674AA00 (152) (810) (181) (330) (130) (406) (565) (170) (152)10 Double Hub Vent 346

(250) SA2675AA00 (157)

11

OUTSIDE CAULKD5501AC (without flashing ring)D5501ACF (with flashing ring)

Foundry Operations

Floor Drains – Outside Caulk

Floor Drains – Inside Caulk

12

Size Wt. A B CPart in lbs in in inNo. (mm) (kg) (mm) (mm) (mm)

2 41 27/8 31/2 5/16(50) (18.6) (73) (89) (8)

D5501B,3 42 37/8 41/2 5/16

BF, BB(80) (19.1) (98) (114) (8)

and BBF 4 48 47/8 51/2 3/8(100) (21.8) (124) (140) (10)

6 49 7 73/4 3/8(150) (22.2) (178) (197) (10)

Strainer plates are duplex stainless steel. Basins are Duriron as standard, but are available in duplex stainless steel on special order at extra cost.

For Basin with Plate 9058, use 9058 B3 and 9058 B4.

Outlet Size Wt.Part in lbsNo. (mm) (kg)

D5501AC 2,3,4 and 6 45(50,80,100 and 150) (20.4)

D5501ACF 2,3,4 and 6 45(50,80,100 and 150) (20.4)


D5501ACB 2,3,4 and 6 53(50,80,100 and 150) (24.1)

D5501ACBF 2,3,4 and 6 53(50,80,100 and 150) (24.1)


D9334 2 37(50) (16.8)

D9334B 2 45(80) (20.4)

Size Wt. B CPart in lbs in inNo. (mm) (kg) (mm) (mm)

D9058-33 70 9 57/8

(80) (31.8) (229) (149)

D9058-44 73 9 63/8

(100) (33.1) (229) (162)

D9058-3, D9058-4

D9334, D9334B (with Sediment Basin)

D5501B (without flashing ring)D5501BF (with flashing ring)D5501BB (with sediment basin and without flashing ring)D5501BBF (with sediment basin and with flashing ring)

OUTSIDE CAULK WITH BASIND5501ACB (without flashing ring)D5501ACBF (with flashing ring)

Foundry Operations

13

Sink Outlet

Part Size A B C D ENo. in in in in in in Stoppers Strainers

(mm) (mm) (mm) (mm) (mm) (mm)

5240MA 11/2 or 2 3/4 to 11/4 10 31/2 43/8 1/8 K5496A AS7948A(40 or 50) (19 to 32) (254) (89) (111) (3)

5588MA 11/2 or 2 1 to 2 10 21/2 37/8 7/16 AY7412A D6021A(40 to 50) (25 to 51) (254) (64) (98) (11)

7594M 11/2 or 2 1 to 2 10 21/2 3 1/4 AY74121A D6021A(40 or 50) (25 to 51) (254) (64) (76) (6)

11713A 11/2 0 to 2 101/4 17/8 35/16 1/4 AY12178A AY49679A(40) (0 to 51) (260) (48) (84) (6)

Furnished with stoppers and flat loose strainer plates. Stoppers and strainers may be purchasedindividually.

Method of Installation Floor Drain Funnel Attachment*With Flashing Ring Funnel attaches to duplex stain-

less steel strainer plates of floordrains. Funnel body, screws and washers are stainless steel.(Approximately 4 pounds.)

Overflow

Part *A* *B* CNo. in in in

(mm) (mm) (mm)

AY7831 A 2 41/8 1(51) (105) (25)

AY7831 B 4 61/8 1(102) (156) (25)

AY7831 C 6 81/8 1(152) (206) (25)

AY7831 D 8 101/8 1(203) (257) (25)

AY7831 E 0 21/8 1(0) (54) (25)

For all sink strainersmarked as both 11/2" or2" size, except plate5240 and 11713.

*Dimensions A and B will vary depending upon the sink strainer in whichoverflow is placed, depth of counterbore, etc. B is given only as a guide.

BEEHIVEOVERFLOW

SINK OUTLET

No. AY7831A, B, C, D and EOverflows

Foundry Operations

Acid Resisting Packing

14

Specifications Long Form:Chemical Waste Drain and Vent Piping SystemI. General

A. Contractor shall furnish and install a chemical waste piping system as indicatedherein. This system shall consist of extra heavy weight, high silicon iron pipeand fittings conforming to the most recent revision of ASTM SpecificationsA518 and A861, as manufactured under the trade name of “Duriron” by theFlowserve Corporation, to be used for above and below grade construction.

B. This chemical waste piping system shall include high silicon iron pipe andfittings of the Bell & Spigot or Mechanical Joint type. It may also include acid-resistant, asbestos-free rope packing or mechanical joint couplings, as manu-factured by Flowserve Corporation for use with Duriron Bell & Spigot pipingand Duriron Mechanical Joint piping, respectively. Where Duriron Bell & Spigotpiping is to be used, virgin lead also is required for proper installation.

C. All materials shall comply with the requirements and referenced standards listedin the International Plumbing Code and all applicable local codes.

II. JointsA. Duriron Bell & Spigot joints shall be made using virgin lead and Red Stripe

Sealite A312 acid-resistant rope packing.B. Duriron Mechanical Joint piping shall be installed using a two-bolt, mechanical

joint coupling, as manufactured by Flowserve Corporation. The Durironmechanical joint coupling consists of an inner sleeve of PTFE, an outer sleeve ofNeoprene rubber (a product of the DuPont DeNemours Company), and an outerband of 300-series stainless steel. Mechanical Joint couplings shall be installedby alternately tightening the nuts to a minimum of 9 ft-lbs and a maximum of11 ft-lbs torque.

C. Duriron may be joined to other types of piping by using adapters made byFlowserve Corporation or the other manufacturer. Glass and other metallic pip-ing systems may be joined to Duriron using a Duriron hub fitting and caulkingthe joint with Red Stripe Sealite A312 rope packing and virgin lead.

Approximate PackingPer Joint*

Pipe Sizein 2 3 4 6 8 10 12 15

(mm) (50) (80) (100) (150) (200) (250) (300) (380)Length

ft 2.0 2.7 3.6 5.1 6.6 8.8 10.5 13.6(m) (0.6) (0.8) (1.1) (1.6) (2.0) (2.7) (3.2) (4.1)

Weightlbs 0.16 0.22 0.29 0.41 0.53 0.71 0.84 1.09(kg) (0.07) (0.10) (0.13) (0.19) (0.24) (0.32) (0.38) (0.49)

PackingSEALITE No. 312A

Package Diameter Lineal ApproxSize in feet lbs per ft

(mm) (m) (kg/m)10 lbs 0.375 118 0.08

(9.6) (35.9) (0.12)

*Calculated on three rounds per joint. Larger sizes above 8" may require more rounds. Rule ofcaulking bell approximately half full of packing predominates and preempts chart.

Foundry Operations

15

Specifications Cont’d

III. Sink ConnectionsSink outlets, tailpieces, traps, and trap adapters shall be high silicon iron or PTFE,as manufactured under the trade name Duriron by the Flowserve Corporation.

IV. Installation & TestingA. All material shall be installed in accordance with the manufacturer’s instructions

and in compliance with the International Plumbing Code and all applicable localcodes.

B. Each length of pipe in a horizontal run shall be supported by a hanger. If the lineconsists in part of fittings, supports shall be placed no further than seven feetapart. P-Traps must be supported individually. Supports shall be placed directlybeneath horizontal fittings that connect to the stack. Vertical lines of pipe shallbe supported at intervals not to exceed fourteen feet. Hangers shall not claspthe pipe so tightly as to prevent normal lateral movement due to expansion.

C. Test in accordance with all applicable code requirements. Prior to testing,Duriron Bell & Spigot and Mechanical Joint piping shall be filled with water andallowed to sit for 24 hours.

V. Above Grade PipingPiping and fittings located in air plenums shall be smoke-proof and non-com-bustible, in compliance with the flame and smoke spread ratings of ASTM E84.

VI. Below Grade PipingA. A trench shall be excavated so as to provide adequate room to make joints,

align, and grade the pipe. The trench bottom shall be properly compacted androck-free and shall support the pipe throughout its entire length.

B. Fill material shall be applied in layers not exceeding 6 inches loose depth andeach layer shall be thoroughly compacted. The first 6 inches of fill material shallbe rock-free.

Short Form:Chemical Waste Drain and Vent Piping System

This system shall consist of high silicon iron pipe and fittings conforming to themost recent revision of ASTM Specifications A518 and A861, as manufactured underthe trade name of “Duriron” by the Flowserve Corporation. Pipe and fittings shall be ofthe Bell & Spigot or Mechanical Joint type installations and be suitable for above andbelow grade construction.

Where used, Bell & Spigot type joints shall be made using virgin lead and RedStripe Sealite A312 acid-resistant rope packing. Duriron Mechanical Joint piping shall be installed using a two-bolt, mechanical joint coupling, as manufactured by FlowserveCorporation. The mechanical joint coupling shall consist of an inner sleeve of PTFE, anouter sleeve of Neoprene rubber (a product of The DuPont DeNemours Company), andan outer band of 300-series stainless steel. Mechanical joint couplings shall be installedby alternately tightening the nuts to a minimum of 9 ft-lbs and a maximum of 11 ft-lbstorque.

For systems being installed underground, a trench shall be excavated so as to pro-vide adequate room to make joints, align, and grade the pipe. The trench bottom shallbe properly compacted and rock-free and shall support the pipe throughout its entirelength. Fill material shall be applied in layers not exceeding 6 inches loose depth andeach layer shall be thoroughly compacted. The first 6 inches of fill material shall berock-free.

The system shall be installed and tested in accordance with the manufacturer’sinstructions and all governing plumbing codes.

Materials Engineering

Multiple Casting Processes

Reactive Alloy Expertise

Rapid Prototyping

Technical Support

Printed in U.S.A.September 2000

© Flowserve Corporation

Flowserve has numerous manufacturing, sales,and service operations throughout the world.Please contact one of the regional centers todetermine the location of the nearest office.

Your local Flowserve representative:Flowserve CorporationFoundry OperationsP.O. Box 1813Dayton, OH 45401-1813 USATelephone: 1 937 226 4536Telefax: 1 937 226 4044E-mail: [email protected] site: www.flowserve.com

Bell and Spigot Pipe Joint

Documents

Transcript of Bell and Spigot Pipe Joint