Before initial use, see “Getting Started” on page 10. · 2 KX-TGE432 3 KX-TGE433 *4 KX-TG3634...

Operating Instructions

Cordless Telephone with Digital Answering MachineModel No. KX-TGE432

KX-TGE433KX-TG3634KX-TGE445KX-TG3640KX-TG3645

Model shown is KX-TGE432.

Before initial use, see “Getting Started”on page 10.

Thank you for purchasing a Panasonic product.Please read these operating instructions before using the unit and save them forfuture reference.

Consulte “Guía Rápida Española”, página 60.

For assistance, visit our Web site: http://shop.panasonic.com/support forcustomers in the U.S.A.

Please register your product: http://shop.panasonic.com/support

TGE43xUS(en)_1112_ver021.pdf 1 2015/11/12 10:12:55

IntroductionModel composition .......................................3Accessory information ..................................3

Important InformationFor your safety .............................................6Important safety instructions ........................7For best performance ...................................7Other information .........................................8Specifications ...............................................9

Getting StartedSetting up ...................................................10Controls ......................................................12Display icons ..............................................13Language settings ......................................14Date and time .............................................14Recording your greeting message .............15Other settings .............................................15

Making/Answering CallsMaking calls ...............................................16Answering calls ..........................................17Useful features during a call .......................17Handset locator ..........................................20Cell locator .................................................20Intercom .....................................................20Power backup operation ............................21

Call BlockCall block ....................................................23Storing unwanted callers ............................23

PhonebookPhonebook .................................................25Speed dial ..................................................27

ProgrammingMenu list .....................................................28Alarm ..........................................................34Silent mode ................................................34Baby monitor ..............................................35Other programming ....................................37Registering a unit .......................................37

Caller ID ServiceUsing Caller ID service ...............................39Caller list ....................................................39

Answering SystemAnswering system ......................................41Turning the answering system on/off .........41Greeting message ......................................41Listening to messages ...............................42Advanced new message alertingfeatures ......................................................43Remote operation .......................................44Answering system settings .........................46

Useful InformationVoicemail service .......................................47Wall mounting ............................................48Error messages ..........................................51Troubleshooting .........................................52FCC and other information .........................57

Guía Rápida EspañolaGuía Rápida Española ...............................60

AppendixCustomer services .....................................65Limited Warranty (ONLY FOR U.S.A.) .......66

IndexIndex...........................................................68

2

Table of Contents

TGE43xUS(en)_1112_ver021.pdf 2 2015/11/12 10:12:55

Model compositionn KX-TGE430 series n KX-TGE440 series

R Model shown is KX-TGE432. R Model shown is KX-TGE445.

Series Model No.Base unit HandsetPart No. Part No. Quantity

KX-TGE430series

KX-TGE432 KX-TGE430 KX-TGEA40 2KX-TGE433 KX-TGE430 KX-TGEA40 3KX-TG3634 KX-TGE430 KX-TGEA40 4

KX-TGE440series

KX-TGE445 KX-TGE440 KX-TGEA40 5KX-TG3640 KX-TGE440 KX-TGEA40 1KX-TG3645 KX-TGE440 KX-TGEA40 5

Accessory information

Supplied accessories

No.Supplied handset qty. 1 units*1 2 units*2 3 units*3 4 units*4 5 units*5

Accessory item/Part number Accessory quantityA AC adaptor/PNLV226-0X 1 1 1 1 1B Telephone line cord*6 1 1 1 1 1

C Wall mounting adaptor/PNKL1044Y2

1 1 1 1 1

D Rechargeable batteries*7 2 4 6 8 10

E Handset cover*8 /PNYNTGEA20BR

1 2 3 4 5

F Belt clip/PNKE1312Z2 1 2 3 4 5G Charger/PNLC1050ZB – 1 2 3 4

*1 KX-TG3640

For assistance, please visit http://shop.panasonic.com/support 3

Introduction

TGE43xUS(en)_1112_ver021.pdf 3 2015/11/12 10:12:55

*2 KX-TGE432*3 KX-TGE433*4 KX-TG3634*5 KX-TGE445/KX-TG3645*6 PQJA10075Y (Black cord), PQJA10075Z (Transparent cord)*7 See page 4 for replacement battery information.*8 The handset cover comes attached to the handset.

A B C D E F

G

Additional/replacement accessoriesPlease contact your nearest Panasonic dealer for sales information (page 65).

Accessory item Model number/SpecificationsRechargeablebatteries

HHR-4DPA*1

R To order, please visit http://shop.panasonic.com/supportBattery type:– Nickel metal hydride (Ni-MH)– 2 x AAA (R03) size for each handset

Headset KX-TCA60, KX-TCA93, KX-TCA400, KX-TCA430Range extender KX-TGA405*2

Key detector KX-TGA20*3

*1 Replacement batteries may have a different capacity from that of the supplied batteries.*2 By installing this unit, you can extend the range of your phone system to include areas

where reception was previously not available. This product can be purchased online. Pleasevisit our Web site: http://shop.panasonic.com/support

*3 By registering the key detector (4 max.) to a Panasonic Digital Cordless Phone andattaching it to an easy-to-lose item in advance, you can locate and find the mislaid item towhich the key detector is attached. Please visit our Web site:http://www.panasonic.com/tga20

Other informationR Design and specifications are subject to change without notice.R The illustrations in these instructions may vary slightly from the actual product.

4 For assistance, please visit http://shop.panasonic.com/support

Introduction

TGE43xUS(en)_1112_ver021.pdf 4 2015/11/12 10:12:55

Expanding your phone system

Handset (optional): KX-TGEA40You can expand your phone system byregistering optional handsets (6 max.) to asingle base unit.R Optional handsets may be a different color

from that of the supplied handsets.


Introduction

TGE43xUS(en)_1112_ver021.pdf 5 2015/11/12 10:12:55

For your safetyTo prevent severe injury and loss of life/property, read this section carefully beforeusing the product to ensure proper and safeoperation of your product.

WARNING

Power connectionR Use only the power source marked on the

product.R Do not overload power outlets and

extension cords. This can result in the riskof fire or electric shock.

R Completely insert the AC adaptor/powerplug into the power outlet. Failure to do somay cause electric shock and/or excessiveheat resulting in a fire.

R Regularly remove any dust, etc. from theAC adaptor/power plug by pulling it fromthe power outlet, then wiping with a drycloth. Accumulated dust may cause aninsulation defect from moisture, etc.resulting in a fire.

R Unplug the product from power outlets if itemits smoke, an abnormal smell, or makesan unusual noise. These conditions cancause fire or electric shock. Confirm thatsmoke has stopped emitting and contact usat http://shop.panasonic.com/support

R Unplug from power outlets and never touchthe inside of the product if its casing hasbeen broken open.

R Never touch the plug with wet hands.Danger of electric shock exists.

InstallationR To prevent the risk of fire or electrical

shock, do not expose the product to rain orany type of moisture.

R Do not place or use this product nearautomatically controlled devices such asautomatic doors and fire alarms. Radiowaves emitted from this product may causesuch devices to malfunction resulting in anaccident.

R Do not allow the AC adaptor or telephoneline cord to be excessively pulled, bent orplaced under heavy objects.

Operating safeguardsR Unplug the product from power outlets

before cleaning. Do not use liquid oraerosol cleaners.

R Do not disassemble the product.R Do not spill liquids (detergents, cleansers,

etc.) onto the telephone line cord plug, orallow it to become wet at all. This maycause a fire. If the telephone line cord plugbecomes wet, immediately pull it from thetelephone wall jack, and do not use.

MedicalR Consult the manufacturer of any personal

medical devices, such as pacemakers orhearing aids, to determine if they areadequately shielded from external RF(radio frequency) energy. (The productoperates in the frequency range of1.92 GHz to 1.93 GHz, and the RFtransmission power is 115 mW (max.).)

R Do not use the product in health carefacilities if any regulations posted in thearea instruct you not to do so. Hospitals orhealth care facilities may be usingequipment that could be sensitive toexternal RF energy.

CAUTION

Installation and locationR Never install telephone wiring during an

electrical storm.R Never install telephone line jacks in wet

locations unless the jack is specificallydesigned for wet locations.

R Never touch uninsulated telephone wires orterminals unless the telephone line hasbeen disconnected at the network interface.

R Use caution when installing or modifyingtelephone lines.

R The AC adaptor is used as the maindisconnect device. Ensure that the ACoutlet is installed near the product and iseasily accessible.


Important Information

TGE43xUS(en)_1112_ver021.pdf 6 2015/11/12 10:12:55

R This product is unable to make calls when:– the handset batteries need recharging or

have failed.– there is a power failure.

BatteryR We recommend using the batteries noted

on page 4. USE ONLY rechargeableNi-MH batteries AAA (R03) size.

R Do not mix old and new batteries.R Do not open or mutilate the batteries.

Released electrolyte from the batteries iscorrosive and may cause burns or injury tothe eyes or skin. The electrolyte is toxic andmay be harmful if swallowed.

R Exercise care when handling the batteries.Do not allow conductive materials such asrings, bracelets, or keys to touch thebatteries, otherwise a short circuit maycause the batteries and/or the conductivematerial to overheat and cause burns.

R Charge the batteries provided with oridentified for use with this product only, inaccordance with the instructions andlimitations specified in this manual.

R Only use a compatible base unit (orcharger) to charge the batteries. Do nottamper with the base unit (or charger).Failure to follow these instructions maycause the batteries to swell or explode.

Attention:

A nickel metal hydride battery that isrecyclable powers the product you havepurchased.Please call 1-800-8-BATTERY(1-800-822-8837) for information on how torecycle this battery.

Important safetyinstructionsWhen using your product, basic safetyprecautions should always be followed toreduce the risk of fire, electric shock, andinjury to persons, including the following:1. Do not use this product near water for

example, near a bathtub, washbowl,kitchen sink, or laundry tub, in a wetbasement or near a swimming pool.

2. Avoid using a telephone (other than acordless type) during an electrical storm.There may be a remote risk of electricshock from lightning.

3. Do not use the telephone to report a gasleak in the vicinity of the leak.

4. Use only the power cord and batteriesindicated in this manual. Do not dispose ofbatteries in a fire. They may explode.Check with local codes for possible specialdisposal instructions.

SAVE THESE INSTRUCTIONS

For best performanceBase unit location/avoiding noiseThe base unit and other compatible Panasonicunits use radio waves to communicate witheach other.R For maximum coverage and noise-free

communications, place your base unit:– at a convenient, high, and central

location with no obstructions betweenthe handset and base unit in an indoorenvironment.

– away from electronic appliances such asTVs, radios, personal computers,wireless devices, or other phones.

– facing away from radio frequencytransmitters, such as external antennasof mobile phone cell stations. (Avoidputting the base unit on a bay window ornear a window.)

R Coverage and voice quality depends on thelocal environmental conditions.



TGE43xUS(en)_1112_ver021.pdf 7 2015/11/12 10:12:55

R If the reception for a base unit location isnot satisfactory, move the base unit toanother location for better reception.

EnvironmentR Keep the product away from electrical noise

generating devices, such as fluorescentlamps and motors.

R The product should be kept free fromexcessive smoke, dust, high temperature,and vibration.

R The product should not be exposed todirect sunlight.

R Do not place heavy objects on top of theproduct.

R When you leave the product unused for along period of time, unplug the product fromthe power outlet.

R The product should be kept away from heatsources such as heaters, kitchen stoves,etc. It should not be placed in rooms wherethe temperature is less than 0 °C (32 °F) orgreater than 40 °C (104 °F). Dampbasements should also be avoided.

R The maximum calling distance may beshortened when the product is used in thefollowing places: Near obstacles such ashills, tunnels, underground, near metalobjects such as wire fences, etc.

R Operating the product near electricalappliances may cause interference. Moveaway from the electrical appliances.

Routine careR Wipe the outer surface of the product

with a soft moist cloth.R Do not use benzine, thinner, or any

abrasive powder.

Other informationCAUTION: Risk of explosion if battery isreplaced by an incorrect type. Dispose of usedbatteries according to the instructions.

Notice for product disposal, transfer,or returnR This product can store your private/

confidential information. To protect yourprivacy/confidentiality, we recommend thatyou erase information such as phonebookor caller list entries from the memory beforeyou dispose of, transfer, or return theproduct.

Notice

ENERGY STARAs an ENERGY STAR® Partner, Panasonichas determined that this product meets theENERGY STAR guidelines for energyefficiency. ENERGY STAR is a U.S.registered mark.



TGE43xUS(en)_1112_ver021.pdf 8 2015/11/12 10:12:55

SpecificationsR Standard:

DECT 6.0 (Digital Enhanced CordlessTelecommunications 6.0)

R Frequency range:1.92 GHz to 1.93 GHz

R RF transmission power:115 mW (max.)

R Power source:120 V AC, 60 Hz

R Power consumption:Base unit:Standby: Approx. 1.0 WMaximum: Approx. 4.3 WCharger:Standby: Approx. 0.1 WMaximum: Approx. 1.8 W

R Operating conditions:0 °C – 40 °C (32 °F – 104 °F), 20 % – 80 %relative air humidity (dry)



TGE43xUS(en)_1112_ver021.pdf 9 2015/11/12 10:12:56

Setting up

Connectionsn Base unit

Connect the AC adaptor to the unit bypressing the plug firmly.Fasten the cord by hooking it.Connect the AC adaptor to the poweroutlet.Connect the telephone line cord to theunit, then to the single-line telephone jack(RJ11C) until you hear a click.A DSL/ADSL filter (not supplied) isrequired if you have a DSL/ADSL service.

Note:R Use only the supplied Panasonic AC

adaptor PNLV226.

1

3

4

4

5

2

n ChargerConnect the AC adaptor to the poweroutlet.

1

Battery installationR USE ONLY rechargeable Ni-MH batteries

AAA (R03) size (1).R Do NOT use alkaline/manganese/Ni-Cd

batteries.R Confirm correct polarities ( , ).

1

R Follow the directions on the display to setup the unit.


Getting Started

TGE43xUS(en)_1112_ver021.pdf 10 2015/11/12 10:12:56

Battery chargingCharge for about 7 hours.R Confirm “Charging” is displayed (1).R When the batteries are fully charged,

“Fully charged” is displayed.

1

Note when setting up

Note for connectionsR The AC adaptor must remain connected at

all times. (It is normal for the adaptor to feelwarm during use.)

R The AC adaptor should be connected to avertically oriented or floor-mounted ACoutlet. Do not connect the AC adaptor to aceiling-mounted AC outlet, as the weight ofthe adaptor may cause it to becomedisconnected.

Note for battery installationR Use the supplied rechargeable batteries.

For replacement, we recommend using thePanasonic rechargeable batteries noted onpage 4, 7.

Note for battery chargingR It is normal for the handset to feel warm

during charging.R Clean the charge contacts of the handset,

base unit, and charger with a soft and drycloth once a month. Before cleaning theunit, disconnect from power outlets and anytelephone line cords. Clean more often ifthe unit is exposed to grease, dust, or highhumidity.

Battery level

Icon Battery levelHigh

Medium

Low

Needs charging.

Empty

Panasonic Ni-MH batteryperformance (supplied batteries)

Operation Operating timeIn continuous use 12 hours max.*1

Not in use (standby) 8 days max.*1

*1 If eco mode is on.

Note:R Actual battery performance depends on

usage and ambient environment.

Intelligent eco modeThis feature automatically reduces handsetpower consumption by suppressing handsettransmission power when the handset is closeto the base unit.R When this feature is activated, is

displayed.R Eco mode is turned off when the clarity

booster is activated (page 18).


Getting Started

TGE43xUS(en)_1112_ver021.pdf 11 2015/11/12 10:12:56

Controls

Handset

A

B

A

KX-TGE440

A

B

A

KX-TGE430

C

F

G

H

E

L

M

N

K

O

B A

D

I

J

Ringer indicatorMessage indicatorBelt clip holesSpeakerMjN/MkN (VOL.: Volume up/down)M N (TALK)Dial keypad (*: TONE)Headset jackMZN (SP-PHONE: Speakerphone)MFLASHNMCALL WAITNMicrophoneReceiverDisplayMOFFN ( )MCALL BLOCKN ( )Charge contacts

n Control type Soft keys

By pressing a soft key, you can select thefeature shown directly above it on thedisplay.

Navigator key– MDN, MCN, MFN, or MEN: Scroll through

various lists and items.– (Volume: MDN or MCN): Adjust the

receiver or speaker volume while talking.– MFN W: View the phonebook entry.– MEN REDIAL: View the redial list.– MCN CID (Caller ID): View the caller list.


Getting Started

TGE43xUS(en)_1112_ver021.pdf 12 2015/11/12 10:12:56

Base unitn KX-TGE430 series: page 3

A C D

G HF I JK

B E

Charge contactsSpeakerMLOCATES CELLNMHANDSET LOCATORNMjN/MkN (VOL.: Volume up/down)Message counterMANSWER ON/OFFNM N (PLAY/STOP)Message indicatorM N (Repeat)M N (Skip)MERASEN

n KX-TGE440 series: page 3

P

JK

O NM

BA L

C

E

F

DG

H

I

Charge contactsSpeakerMHOLDN MCONFNMREDIALN MPAUSENMFLASHN MCALL WAITNMZN (SP-PHONE: Speakerphone)SP-PHONE indicatorMessage counterM N (PLAY/STOP)Message indicatorMANSWER ON/OFFNMLOCATES CELLNMLOCATORN MINTERCOMNMjN/MkN (VOL.: Volume up/down)MERASEN MMUTENM N (Skip)M N (Repeat)MicrophoneDial keypad (*: TONE)

Display iconsHandset display items

Item MeaningWithin base unit range


Getting Started

TGE43xUS(en)_1112_ver021.pdf 13 2015/11/12 10:12:56

Item MeaningOut of base unit range

The line is in use.R When flashing:

The call is put on hold.R When flashing rapidly: An

incoming call is now beingreceived.

Eco mode is on. (page 11)

Noise reduction is set.(page 18)Equalizer is set. (page 18)

Z Speakerphone is on.(page 16)Ringer volume is off.(page 17, 30)Silent mode is on. (page 34)

Call sharing mode is off.(page 32)Alarm is on. (page 34)

Handset number

Battery level

Blocked call (page 23)

Clarity booster is on.(page 18)Baby monitor is activated. Thename/number displayed nextto the icon indicates themonitoring unit. (page 35)

In use Answering system is beingused by another handset or thebase unit.

Line inuse

Someone is using the line.

Base unit display item

Item Meaning“Greeting only” isselected. Caller messages arenot recorded. (page 46)

Language settings

Display language1 MMENUN#1102 MbN: Select the desired setting. a

MSAVEN a MOFFN

Voice announcement languageYou can select the language used for thefollowing features.– Answering system guidance– Talking Caller ID1 MMENUN#1122 MbN: Select the desired setting. a

MSAVEN a MOFFN

Date and time1 MMENUN#1012 Enter the current month, date, and year

by selecting 2 digits for each.Example: July 12, 201607 12 16

3 MOKN4 Enter the current hour and minute

(12-hour clock format) by selecting 2digits for each.Example: 9:3009 30

5 *: Select “AM” or “PM”.6 MSAVEN a MOFFNNote:R When English is selected as the display

language, 12-hour clock format is used.When Spanish is selected, 24-hour clockformat is used.


Getting Started

TGE43xUS(en)_1112_ver021.pdf 14 2015/11/12 10:12:56

Recording your greetingmessageYou can record your own greeting messageinstead of using a pre-recorded greetingmessage. See page 41 for details.1 MMENUN#3022 MbN: “Yes” a MSELECTN3 Record a greeting message. a MSTOPN

a MOFFN

Other settings

Dialing modeIf you cannot make calls, change this settingaccording to your telephone line service. Thedefault setting is “Tone”.“Tone”: For tone dial service.“Pulse”: For rotary/pulse dial service.1 MMENUN#1202 MbN: Select the desired setting. a

MSAVEN a MOFFN


Getting Started

TGE43xUS(en)_1112_ver021.pdf 15 2015/11/12 10:12:56

Making calls

Using the handset1 Lift the handset and then dial the phone

number.R To correct a digit, press MCLEARN.

2 Press M N to make the call.R To make the call using the

speakerphone, press MZN.3 When you finish talking, press MOFFN or

place the handset on the base unit orcharger.

Note:R To switch to the speaker, press MZN.

To switch back to the receiver, press MZN/M N.

R In step 1, you can store the dialed phonenumber to the phonebook by pressingMSAVEN.

Making a call using the redial listThe last 5 phone numbers dialed are stored inthe redial list (each 48 digits max.).1 MEN REDIAL2 MbN: Select the desired entry.3 M N

Erasing a number in the redial list1 MEN REDIAL2 MbN: Select the desired entry. a

MERASEN3 MbN: “Yes” a MSELECTN a MOFFN

Using the base unit

Available for:KX-TGE440 series (page 3)

1 MZN

2 Dial the phone number.3 When the other party answers, speak into

the microphone.

4 When you finish talking, press MZN.Note:R While on a call, you can switch from the

base unit to the handset:– Press M N on the handset, then pressMZN on the base unit with the callsharing mode on (page 32).

– If the handset is on the base unit, simplylift it.

Redialing the last number dialedMZN a MREDIALN

Adjusting the receiver or speakervolume

Handset / Base unit*1

*1 KX-TGE440 series: page 3

Press MjN or MkN repeatedly while talking.

Pause (for PBX/long distanceservice users)A pause is sometimes required when makingcalls using a PBX or long distance service.When storing a calling card access numberand/or PIN in the phonebook, a pause is alsoneeded (page 26).Example: If you need to dial the line accessnumber “9” when making outside calls with aPBX:

Handset

1 9 a MDN (Pause)2 Dial the phone number. a M N

Base unit*1


1 MZN

2 9 a MPAUSEN3 Dial the phone number.Note for handset and base unit:R A 3.5 second pause is inserted each time

you press MDN (Pause) on the handset orMPAUSEN on the base unit.


Making/Answering Calls

TGE43xUS(en)_1112_ver021.pdf 16 2015/11/12 10:12:56

Answering calls

Using the handsetWhen a call is being received, the ringerindicator flashes rapidly.1 Lift the handset and then press M N or

M N when the unit rings.2 When you finish talking, press MOFFN or

place the handset on the base unit orcharger.

Any key answer: You can answer the call bypressing any dial key.Auto talk: You can answer calls simply bylifting the handset (page 32).Temporary handset ringer off: You can turnthe ringer off temporarily by pressing M N.

Using the base unit

Available for:KX-TGE440 series (page 3)

When a call is being received, the SP-PHONEindicator flashes rapidly.1 Press MZN when the unit rings.2 Speak into the microphone.3 When you finish talking, press MZN.

Adjusting the ringer volumeHandset

Press MjN or MkN repeatedly to select thedesired volume.R To turn the ringer off, press MkN repeatedly.

Base unitPress MjN or MkN repeatedly to select thedesired volume.R To turn the ringer off, press and hold MkN

until the unit beeps.

Useful features during acall

HoldHandset

1 Press MMENUN during an outside call.2 MbN: “Hold” a MSELECTN3 To release hold, press M N.

R Another handset user can take the callby pressing M N.

R The base unit user can take the call bypressing MZN. (KX-TGE440 series:page 3)

Base unit*1


1 Press MHOLDN during an outside call.2 To release hold, press MZN.

R A handset user can take the call bypressing M N.

Note for handset and base unit:R While an outside call is on hold, the

SP-PHONE indicator on the base unitflashes.

R After holding for 10 minutes, the call isdisconnected.

MuteHandset

1 Press MMUTEN during a call.2 To return to the call, press MMUTEN.Note:R MMUTEN is a soft key visible on the display

during a call.

Base unit*1


1 Press MMUTEN during a call.R The SP-PHONE indicator flashes.

2 To return to the call, press MMUTEN.



TGE43xUS(en)_1112_ver021.pdf 17 2015/11/12 10:12:56

FlashHandset / Base unit*1


MFLASHN allows you to use the specialfeatures of your host PBX such as transferringan extension call, or accessing optionaltelephone services.Note:R To change the flash time, see page 32.

For call waiting or Call WaitingCaller ID service usersTo use call waiting or Call Waiting Caller ID,you must first subscribe with your phoneservice provider.This feature allows you to receive calls whileyou are already talking on the phone. If youreceive a call while on the phone, you will heara call waiting tone.If you subscribe to both Caller ID and CallWaiting with Caller ID services, the 2ndcaller’s information is displayed on the unitthat is in use after you hear the call waitingtone.



1 Press MCALL WAITN to answer the 2ndcall.

2 To switch between calls, press MCALLWAITN.

Note:R Please contact your phone service provider

for details and availability of this service inyour area.

Temporary tone dialing (forrotary/pulse service users)



Press * (TONE) before entering accessnumbers which require tone dialing.

Handset clarity boosterThis feature can improve sound clarity whenthe handset is used in an area where theremay be interference. During an outside call,this feature is turned on automatically whennecessary.R When this feature is turned on, is

displayed.

Handset noise reductionThis feature allows you to hear the voice ofthe person you are talking to more clearly, byreducing the surrounding noise coming fromthe other party’s telephone.1 Press MMENUN while talking.2 MbN: “Noise reduction on” or

“Noise reduction off” aMSELECTN

Note:R Depending on the environment where this

handset is being used, this feature may notbe effective.

R This feature is not available while using thespeakerphone.

Handset equalizerThis feature clarifies the voice of the personyou are talking to, producing a morenatural-sounding voice that is easier to hearand understand.1 Press MMENUN while talking.2 MbN: “Equalizer” a MSELECTN3 MbN: Select the desired setting.4 Press MOKN to exit.Note:R Depending on the condition and quality of

your telephone line, this feature mayemphasize existing line noise. If it becomesdifficult to hear, turn this feature off.

R This feature is not available while using thespeakerphone.

R When both the “Equalizer” setting andnoise reduction are activated, isshown on the display.



TGE43xUS(en)_1112_ver021.pdf 18 2015/11/12 10:12:56

Call shareYou can join an existing outside call.

HandsetTo join the conversation, press M N whenthe other unit is on an outside call.

Base unit*1


To join the conversation, press MZN when thehandset is on an outside call.Note for handset and base unit:R A maximum of 3 parties (including 1 outside

party) can join a conversation using 2extensions. (3-way conference)

R To prevent other users from joining yourconversations with outside callers, turn callsharing mode off (page 32).

Transferring calls, conferencecallsOutside calls can be transferred or aconference call with an outside party can bemade:– between 2 handsets– between a handset and the base unit*1*1 KX-TGE440 series: page 3

Handset

1 During an outside call, press MMENUN.2 MbN: “Intercom” a MSELECTN3 MbN: Select the desired unit. a MSELECTN

R If you select “Voice paging”, thecall will be switched from theear-receiver mode to thespeakerphone mode.

4 Wait for the paged party to answer.R If the paged party does not answer,

press MBACKN to return to the outsidecall.

5 To complete the transfer:Press MOFFN.To establish a conference call:MMENUN a MbN: “Conference” aMSELECTN

R To leave the conference, press MOFFN.The other 2 parties can continue theconversation.

R To put the outside call on hold:MMENUN a MbN: “Hold” aMSELECTNTo resume the conference: MMENUNa MbN: “Conference” a MSELECTN

R To cancel the conference: MMENUN aMbN: “Stop conference” aMSELECTNYou can continue the conversationwith the outside caller.

Base unit*1


1 During an outside call, pressMINTERCOMN.When 2 or more handsets areregistered:– To page a specific handset, enter the

handset number.– To page all handsets, press 0 or wait

for a few seconds.2 Wait for the paged party to answer.

R If paged party does not answer, pressMINTERCOMN to return to the outsidecall.

3 To complete the transfer:Press MZN.R The outside call is being routed to the

handset.To establish a conference call:Press MCONFN.R To leave the conference, press MZN.

The other 2 parties can continue theconversation.

R To put the outside call on hold, pressMHOLDN. To resume the conference,press MCONFN.



TGE43xUS(en)_1112_ver021.pdf 19 2015/11/12 10:12:56

Handset locatorYou can locate a misplaced handset bypaging it.1 Base unit: Press MLOCATORN or

MHANDSET LOCATORN.R All registered handsets beep for 1

minute.2 To stop paging:

Base unit:Press MLOCATORN or MHANDSETLOCATORN.Handset:n KX-TGE430 series: page 3

Press MOFFN.n KX-TGE440 series: page 3

Press M N, then press MOFFN.

Cell locatorThis feature allows you to locate a misplacedcellular phone by pressing the MLOCATESCELLN button on the base unit and callingyour cellular phone. You must assign yourcellular phone’s phone number to the buttonbeforehand. Only 1 cellular phone number (24digits max.) can be assigned.

Adding a phone number1 MMENUN#248

R If you have already stored a cellularphone number, the current number isdisplayed.

2 Enter your cellular phone number. aMSAVEN a MOFFN

Erasing the number1 MMENUN#2482 Press and hold MCLEARN until all digits

are erased. a MSAVEN a MOFFN

Calling the misplaced cellularphoneBase unit: MLOCATES CELLNR To stop calling:

– KX-TGE430 series: press MLOCATESCELLN again.

– KX-TGE440 series: press MZN.Important:R While the base unit is calling the cellular

phone, the outside line is used.– KX-TGE430 series: Even if the cellular

phone answers, you cannot talk with thecellular phone and the base unit beepsfor 1 minute. To end the call, pressMLOCATES CELLN on the base unit.

– KX-TGE440 series: When the cellularphone answers, you can talk with thecellular phone. To end the call, pressMZN on the base unit.

Charges may be incurred if the cellularphone answers the call.

IntercomIntercom calls can be made:– between handsets– between a handset and the base unit*1*1 KX-TGE440 series: page 3

Note:R When paging unit(s), the paged unit(s)

beeps for 1 minute.R If you receive an outside call while talking

on the intercom, the interrupt tone sounds.– Handset: To finish intercom, pressMOFFN. To answer the call, press M N.

– Base unit: To finish intercom, pressMZN. To answer the call, press MZNagain.

Making an intercom callHandset

1 MMENUN a MbN: “Intercom” aMSELECTN



TGE43xUS(en)_1112_ver021.pdf 20 2015/11/12 10:12:56

2 MbN: Select the desired unit or “Voicepaging”. a MSELECTNR If you select “Voice paging”, speak

into the microphone after the beep.Your voice will be heard using thespeakers of the base unit*1 and allhandsets, until a paged party answersyour page or until you press MOFFN.After the other party answers, thespeakerphone mode is turned on.

3 When you finish talking, press MOFFN.*1 KX-TGE440 series: page 3

Note:R You can also use the MINTERCOMN soft

key, if displayed, to make intercom calls.R You cannot use voice paging if other units

are in use.R Voice paging is not available when a range

extender (KX-TGA405) is registered to thebase unit.

Base unit*1


1 Press MINTERCOMN.When 2 or more handsets areregistered:– To page a specific handset, enter the

handset number.– To page all handsets, press 0 or wait

for a few seconds.2 When you finish talking, press MZN.

Answering an intercom callHandset

1 Press M N to answer the page.2 When you finish talking, press MOFFN.

Base unit*1


1 Press MZN to answer the page.2 When you finish talking, press MZN.

Turning auto intercom on/offThis feature allows the handset or base unit toanswer intercom calls automatically when it iscalled. You do not need to press M N orMZN. When this feature is set to “On”, themonitoring handset or base unit for the babymonitor feature (page 37) will also answerbaby monitor calls automatically. The defaultsetting is “Off”.1 For handset setting: MMENUN#273

For base unit setting (using ahandset)*1: MMENUN#*273

2 MbN: Select the desired setting. aMSAVEN a MOFFN


Note:R This feature is not available for all handsets

paging and voice paging even if it is turnedon.

Power backup operationWhen a power failure occurs, the chargedhandset temporarily supplies power to thebase unit (power backup mode). This allowsyou to make and receive calls using a handsetduring a power failure. The base unit will notperform any other functions. However, somefunctions such as Caller ID and phonebookare available only when using a handset otherthan the handset supplying power to the baseunit. You can program “Power failure”and the default setting is “Auto” (page 32).Important:R If a handset is not placed on the base unit

when a power failure occurs, “Base nopower Press OFF” is displayed. Afterpressing MOFFN on the handset, place it onthe base unit to start power backup mode.

R Power backup mode will not work if thebattery level of the power supplyinghandset is or .

R Do not lift the power supplying handsetfrom the base unit during power backupmode.



TGE43xUS(en)_1112_ver021.pdf 21 2015/11/12 10:12:56

Panasonic Ni-MH batteryperformance (supplied batteries)during power backup modeWhen the batteries are fully charged,operating time of the handset in power backupmode varies depending on usage.– Continuous use of the handset in power

backup mode: 1.5 hours max.– Continuous use of the handset other than a

handset in power backup mode: 2 hoursmax.

– Not in use in power backup mode: 2 hoursmax.

Making calls during a powerfailuren When only 1 handset is registered:

1 Lift the handset and dial the phonenumber.

2 Within 1 minute, place the handset onthe base unit.R Wait until speakerphone is turned

on automatically and the call ismade.

3 When the other party answers the call,keep the handset on the base unit andtalk using the speakerphone.

4 When you finish talking, press MOFFN.n When 2 or more handsets are registered:

You should leave one handset on the baseunit for supplying the power, and useanother handset for making calls.

Note:R The range of the base unit is limited during

a power failure. Please use the handsetclose to the base unit.

Making a call using the redial listn When only 1 handset is registered:

1 Lift the handset.2 MEN REDIAL3 MbN: Select the desired entry.

4 Within 1 minute, place the handset onthe base unit.R Wait until speakerphone is turned

on automatically and the call ismade.

n When 2 or more handsets are registered:You should leave one handset on the baseunit for supplying the power, and useanother handset for making calls.

Making a call using the phonebookThere must be at least 2 handsetsregistered to the base unit in order for thephonebook feature to be used during apower failure.You should leave one handset on the baseunit for supplying the power, and use anotherhandset for making calls.

Answering calls during a powerfailuren When only 1 handset is registered:

1 When the unit rings, keep the handseton the base unit and press M N orMZN.R Speakerphone is turned on.

2 When you finish talking, press MOFFN.n When 2 or more handsets are registered:

When the unit rings, use a handset which isnot supplying power to the base unit.R Do not use or lift the handset which is

placed on the base unit during powerbackup mode.

Note:R The range of the base unit is limited during

a power failure. Please use the handsetclose to the base unit.



TGE43xUS(en)_1112_ver021.pdf 22 2015/11/12 10:12:56

Call blockYou can press the MCALL BLOCKN button inthe following situations to disconnect thecurrent call and add a phone number to thecall block list:– when an incoming call is being received– when an incoming call is being recorded by

the answering system– when talking on an outside callOnce a phone number has been added to thecall block list, the unit will block calls from thatphone number in the future.1 Press MCALL BLOCKN under the

situations shown above.2 Confirm the call block number and press

MYESN.R The call block number is stored in the

call block list, “Caller blocked” isdisplayed, and then the call isdisconnected.

Note:R If the call has no phone number, the call is

blocked but it is not stored in the call blocklist.

R The call block feature is not available forintercom calls or calls received by callwaiting.

R Blocked calls are logged in the caller list.

Storing unwanted callersThe unit can block calls by storing the desireditems in the call block list beforehand (CallerID subscribers only).– “Block a single number”: The unit

blocks calls from specific phone numbersstored in the call block list.

– “Block range of numbers”: The unitblocks calls that begin with a number storedin the call block list, such as a toll-freephone number prefix or certain area codes.

– “Block unknown CID”: The unit blockscalls that have no phone number.

Single phone numbers and ranges of numberscan be stored in the call block list up to 250items in total.

Blocking unwanted callers:When a call is received, the unit rings once*1

while caller information is being received.If the caller’s phone number matches an entryin the call block list, the unit emits no sound tothe caller, and disconnects the call.*1 If you do not want this one ring to sound,

select “No” in “Turning the first ring onand off” (page 24).

Storing a single phone numberImportant:R We recommend storing 10 digits (including

the area code). If only 7 digits are stored, allnumbers that have the same last 7 digitswill be blocked.

Adding call blocked numbers fromthe caller list1 MCN CID2 MbN: Select the desired entry to be

blocked.R To edit the number: MMENUN a MbN:

“Edit” a MSELECTNPress MEDITN repeatedly until thephone number is shown in the 10-digitformat. a MSAVEN a MbN: “Callblock” a MSELECTN a Go to step4.

3 MCALL BLOCKN4 MbN: “Yes” a MSELECTN5 Edit the phone number if necessary (24

digits max.). a MSAVEN a MOFFN

Adding call blocked numbersmanually1 MCALL BLOCKN2 MbN: “Block a single number” a

MSELECTN3 MMENUN a MbN: “Add” a MSELECTN4 Enter the phone number (24 digits max.).

a MSAVEN a MOFFN


Call Block

TGE43xUS(en)_1112_ver021.pdf 23 2015/11/12 10:12:56

Storing a range of number1 MCALL BLOCKN2 MbN: “Block range of numbers” a

MSELECTN3 MMENUN a MbN: “Add” a MSELECTN4 Enter the desired number (2-8 digits). a

MSAVEN a MOFFN

Blocking incoming calls thathave no phone numberYou can block calls when no phone number isprovided, such as private callers or out of areacalls.1 MCALL BLOCKN2 MbN: “Block unknown CID” a

MSELECTN3 MbN: Select the desired setting. a

MSAVEN a MOFFN

Turning the first ring on and offYou can choose whether the first ring soundswhen a call is received.“Yes” (default): The first ring for all calls willbe heard, including calls from blocked phonenumbers.“No”: The first ring is muted for all calls. If thissetting is selected, the unit will never ring forcalls from blocked phone numbers.1 MCALL BLOCKN2 MbN: “One ring for blocked call”

a MSELECTN3 MbN: Select the desired setting. a

MSAVEN a MOFFN

Viewing/editing/erasing callblock numbers1 MCALL BLOCKN2 MbN: “Block a single number” or

“Block range of numbers” aMSELECTN

3 MbN: Select the desired entry.R After viewing, press MOFFN to exit.

4 To edit a number:MEDITN a Edit the number. a MSAVENa MOFFNTo erase a number:MERASEN a MbN: “Yes” a MSELECTNa MOFFN

Note:R When editing, press the desired dial key to

add digits and press MCLEARN to erasedigits.

Erasing all call block numbers1 MCALL BLOCKN2 MbN: “Block a single number” or

“Block range of numbers” aMSELECTN

3 MMENUN a MbN: “Erase all” aMSELECTN

4 MbN: “Yes” a MSELECTN5 MbN: “Yes” a MSELECTN a MOFFN


Call Block

TGE43xUS(en)_1112_ver021.pdf 24 2015/11/12 10:12:56

PhonebookYou can add 100 names (16 characters max.)and phone numbers (24 digits max.) to thephonebook, and assign each phonebook entryto the desired group (page 25).Important:R All entries can be shared by any registered

handset.

Adding phonebook entries1 MFN W a MMENUN2 MbN: “Add new entry” a MSELECTN3 Enter the party’s name. a MOKN4 Enter the party’s phone number. a MOKN5 MbN: Select the desired group. a

MSELECTN 2 times a MOFFNNote:R In step 3, you can switch the language for

entering characters.# a MbN: Select the desired language. aMOKN

Entering charactersPress the dial key that corresponds to thedesired character. Press repeatedly to scrollthrough the available characters.The following operations are also available.

Key Operation* Switch between the

uppercase and lowercase(A « a)

MFN MEN Move the cursorMCLEARN Erase the character or number

R To erase all, press andhold it.

R To enter another character that is locatedon the same dial key, first press MEN tomove the cursor to the next space.

R If you do not press any dial key within 2seconds after entering a character, the

character is fixed and the cursor moves tothe next space.

Storing a redial list number to thephonebookPhone numbers of up to 24 digits can bestored in the phonebook.1 MEN REDIAL2 MbN: Select the desired entry. a MSAVEN3 To store the name, continue from step 3,

“Editing entries”, page 26.Note:R The name stored in the phonebook will be

reflected in the redial list after you make acall using that phonebook entry.

Storing caller information to thephonebook1 MCN CID2 MbN: Select the desired entry. a MMENUN

R To edit the number: MbN: “Edit” aMSELECTNPress MEDITN repeatedly until thephone number is shown in the desiredformat. a MSAVEN a MbN:“Phonebook” a MSELECTN a Goto step 4.

3 MbN: “Save phonebook” a MSELECTN4 Continue from step 3, “Editing entries”,

page 26.

GroupsGroups can help you find entries in thephonebook quickly and easily. You canchange the names of groups assigned forphonebook entries (“Friends”, “Family”, etc.).By assigning different ringer tones for differentgroups of callers, you can identify who iscalling (ringer ID), if you have subscribed toCaller ID service.


Phonebook

TGE43xUS(en)_1112_ver021.pdf 25 2015/11/12 10:12:56

Changing group names/setting ringerIDThe default group name is “Group 1” to“Group 9”.1 MFN W a MMENUN2 MbN: “Group” a MSELECTN3 MbN: Select the desired group. a

MSELECTN4 To change group names

MbN: “Group name” a MSELECTN aEdit the name (10 characters max.). aMSAVENTo set group ringer toneMbN: Select the current setting of thegroup ringer tone. a MSELECTN a MbN:Select the desired ringer tone. a MSAVEN

5 MOFFN

Finding and calling from aphonebook entry1 MFN W2 To scroll through all entries

MbN: Select the desired entry.To search by first character

Press the dial key (0 to 9, or #)which contains the character you aresearching for.MbN: Scroll through the phonebook ifnecessary.

To search by groupMGROUPNMbN: Select the desired group. aMSELECTNMbN: Scroll through the phonebook ifnecessary.

3 M N

Editing entries1 Find the desired entry (page 26).2 MMENUN a MbN: “Edit” a MSELECTN3 Edit the name if necessary. a MOKN4 Edit the phone number if necessary. a

MOKN

5 MbN: Select the desired group (page 25).a MSELECTN 2 times a MOFFN

Erasing entries

Erasing an entry1 Find the desired entry (page 26).2 MMENUN a MbN: “Erase” a MSELECTN3 MbN: “Yes” a MSELECTN a MOFFN

Erasing all entries1 MFN W a MMENUN2 MbN: “Erase all” a MSELECTN3 MbN: “Yes” a MSELECTN4 MbN: “Yes” a MSELECTN a MOFFN

Chain dialThis feature allows you to dial phone numbersin the phonebook while you are on a call. Thisfeature can be used, for example, to dial acalling card access number or bank accountPIN that you have stored in the phonebook,without having to dial manually.1 During an outside call, press MFN W.2 MbN: Select the desired entry.3 Press MCALLN to dial the number.Note:R When storing a calling card access number

and your PIN in the phonebook as onephonebook entry, press MDN (Pause) to addpauses after the number and PIN asnecessary (page 16).

R If you have rotary/pulse service, you needto press * (TONE) before pressing MFNW in step 1 to change the dialing modetemporarily to tone. When adding entries tothe phonebook, we recommend adding *(TONE) to the beginning of phone numbersyou wish to chain dial (page 25).


Phonebook

TGE43xUS(en)_1112_ver021.pdf 26 2015/11/12 10:12:56

Speed dialYou can assign 1 phone number to each ofthe dial keys (1 to 9) on the handset.

Adding phone numbers to speeddial keysn By entering phone numbers:

1 Press and hold the desired speed dialkey (1 to 9). a MADDN

2 MbN: “Manual” a MSELECTN3 Enter the party’s name (16 characters

max.). a MOKN4 Enter the party’s phone number (24

digits max.). a MOKN a MSELECTNa MOFFN

n From the phonebook:1 Press and hold the desired speed dial

key (1 to 9). a MADDN2 MbN: “Phonebook” a MSELECTN3 MbN: Select the desired entry. a

MSAVEN a MOFFNNote:R If you edit a phonebook entry which is

assigned to a speed dial key, the editedentry does not transfer to the speed dialkey.

Editing an entry1 Press and hold the desired speed dial key

(1 to 9). a MMENUN2 MbN: “Edit” a MSELECTN3 Edit the name if necessary. a MOKN4 Edit the phone number if necessary. a

MOKN a MSELECTN a MOFFN

Erasing an entry1 Press and hold the desired speed dial key

(1 to 9). a MMENUN2 MbN: “Erase” a MSELECTN3 MbN: “Yes” a MSELECTN a MOFFN

Viewing an entry/Making a call1 Press and hold the desired speed dial key

(1 to 9).2 To make a call, press M N.


Phonebook

TGE43xUS(en)_1112_ver021.pdf 27 2015/11/12 10:12:56

Menu listTo access the features, there are 2 methods.n Scrolling through the display menus

1 MMENUN2 Press MCN or MDN to select the desired main menu. a MSELECTN3 Press MCN or MDN to select the desired item from the next sub-menus. a MSELECTN4 Press MCN or MDN to select the desired setting. a MSAVEN

n Using the direct command code1 MMENUN a Enter the desired code.

Example: Press MMENUN#101.2 Select the desired setting. a MSAVEN

Note:R To exit the operation, press MOFFN.R In the following table, < > indicates the default settings.R In the following table, indicates the reference page number.R Display menu order and sub-menu may vary depending on your model.

Display menu tree and direct command code tableMain menu: W “Phonebook”

Operation CodeViewing the phonebook entry. #280 26

Main menu: “Caller list”

Operation CodeViewing the caller list. #213 39

Main menu: “Answering device”

Sub-menu 1 Sub-menu 2 Settings CodePlay new message – – #323 42Play all message – – #324 42Erase allmessage*1

– – #325 43

Greeting Record greeting*1 – #302 41

Check greeting – #303 42

Pre-recorded*1

(Reset to pre-recordedgreeting)

– #304 42


Programming

TGE43xUS(en)_1112_ver021.pdf 28 2015/11/12 10:12:56

Sub-menu 1 Sub-menu 2 Settings CodeNew messagealert*1

Outgoing call– On/Off

On<Off>

#338 43

Outgoing call– Notification to

–

Outgoing call– Remote code

Activate<Inactivate>

Base unit beep On<Off>

#339 43

Settings Ring count*1 Toll saver2-7 rings<4 rings>

#211 46

Recording time*1 <3 min>1 minGreeting only*2

#305 46

Remote code*1 <111> #306 45

Screen call– Handset

<On>Off

#310 46

Screen call– Base unit*1, *3

<On>Off

#G310 46

Answer on*1 – – #327 41

Answer off*1 – – #328 41

Main menu: “Voicemail access”

Operation CodeListening to voicemail messages. #330 48

Main menu: “Intercom”

Operation CodePaging the desired unit. #274 20

Main menu: “Set date & time”

Sub-menu 1 Sub-menu 2 Settings CodeDate and time*1 – – #101 14

Memo alarm Alarm1-3 <Off>OnceDailyWeekly

#720 34

Time adjustment*1, *4 – <Caller IDauto>Manual

#226 –


Programming

TGE43xUS(en)_1112_ver021.pdf 29 2015/11/12 10:12:57

Main menu: “Speed dial”

Operation CodeViewing the speed dial entry. #261 27

Main menu: “Settings”

Sub-menu 1 Sub-menu 2 Settings CodeRing adjustments Ringer volume

(Handset)Off–6 <6> #160 –

Ringer tone*5, *6

(Handset)<Tone 1> #161 –

Silent mode– Handset

On/Off– On– <Off>

#238 34

Start/End– <11:00 PM/

06:00 AM>

#237 35

Select groupGroup 1-9

#241 35

Silent mode– Base unit*1, *3

On/Off– On– <Off>

#G238 34

Start/End– <11:00 PM/

06:00 AM>

#G237 35

Select groupGroup 1-9

#G241 35

Set date & time Date and time*1 – #101 14

Memo alarm– Alarm1-3

<Off>OnceDailyWeekly

#720 34

Time adjustment*1, *4 <Caller IDauto>Manual

#226 –

Talking caller ID Handset <On>Off

#162 39

Base unit*1 On<Off>

#G162


Programming

TGE43xUS(en)_1112_ver021.pdf 30 2015/11/12 10:12:57

Sub-menu 1 Sub-menu 2 Settings CodeKey detectorsetting*7

– 1: Add newdevice (forDetector1)*8

– 2: Add newdevice (forDetector2)



Change name*1 Detector1 #6561 –

Detector2*9 #6562*9

Detector3*9 #6563*9

Detector4*9 #6564*9

Registration – #6571 –

#6572*9

#6573*9

#6574*9

Deregistration – #6581 –

#6582*9

#6583*9

#6584*9

Call block*1 Block a singlenumber

– #217 23

Block range ofnumbers

– 24

Block unknown CID(CID: Caller ID)

Block <Unblock>

#240 24

One ring for blockedcall

<Yes>No

#173 24

Speed dial – – #261 27Cell locator – – #248 20

Record greeting*1 – – #302 41

Voicemail Save VM access#*1

(VM: Voicemail)– #331 47

VM tone detect*1 <On> Off

#332 47

Message indicator – <On> Off

#340 46

LCD contrast(Display contrast)

– Level 1–4 <2> #145 –

Handset name – – #104 37Display name – On

<Off>#105 37


Programming

TGE43xUS(en)_1112_ver021.pdf 31 2015/11/12 10:12:57

Sub-menu 1 Sub-menu 2 Settings CodeAuto intercom Handset On

<Off>#273 21

Base unit*1, *3 On <Off>

#G273

Key tone – <On>Off

#165 –

Caller ID edit(Caller ID number autoedit)

– <On> Off

#214 40

Auto talk*10 – On <Off>

#200 17

Set tel line Set dial mode*1 <Tone>Pulse

#120 15

Set flash time*1, *11 80 ms90 ms100 ms110 ms160 ms200 ms250 ms300 ms400 ms600 ms<700 ms>900 ms

#121 18

Set line mode*1, *12 A <B> #122 –

Call sharing*1 – <On> Off

#194 19

Registration Register handset – #130 37

Deregistration*2 – #131 38

Power failure – <Auto>Off

#152 21

Change language Display <English> Español

#110 14

Announcement*1 <English> Español

#112 14

Main menu: “Customer support”

Operation CodeDisplaying customer support Web address. #680 –


Programming

TGE43xUS(en)_1112_ver021.pdf 32 2015/11/12 10:12:57

Main menu: “Baby monitor”

Sub-menu 1 Sub-menu 2 Settings CodeOn/Off – On

<Off>#268 35

Sensitivity level – Low<Middle>High

#269 36

Main menu: “Key detector”*7

Sub-menu 1 Sub-menu 2 Settings CodeSearch – – #655 –Battery check – –

*1 If you program these settings using one of the units, you do not need to program the sameitem using another unit.

*2 This menu is not displayed when scrolling through the display menus. It is only available indirect command code.

*3 KX-TGE440 series: page 3*4 This feature allows the unit to automatically adjust the date and time each time caller

information including date and time is received.To turn this feature on, select “Caller ID auto”. To turn this feature off, select“Manual”. (Caller ID subscribers only)To use this feature, set the date and time first (page 14).

*5 If you subscribe to a distinctive ring service (such as IDENTA-RING), select a tone (tone 1 to2). If you select a melody, you cannot distinguish lines by their ringers.

*6 The preset melodies in this product (“Tone 3” - “Melody 10”) are used with permission of© 2004 - 2013 Copyrights Vision Inc.

*7 This setting is available when you have the key detector (KX-TGA20). Read the installationmanual for more information on the key detector.

*8 For models with supplied key detectors, the display shows “1: Detector1”.*9 If you register 2 or more key detectors.*10 If you subscribe to a Caller ID service and want to view the caller’s information after lifting up

the handset to answer a call, turn off this feature.*11 The flash time depends on your telephone exchange or host PBX. Contact your PBX

supplier if necessary. The setting should stay at “700 ms” unless pressing MFLASHN fails topick up the waiting call.

*12 Generally, the line mode setting should not be changed. This setting automatically maintainsreceiver volume at the proper level depending on the current telephone line condition. Setthe line mode to “A” if telephone line condition is not good.


Programming

TGE43xUS(en)_1112_ver021.pdf 33 2015/11/12 10:12:57

AlarmAn alarm sounds at the set time for 1 minuteand is repeated 5 times at 5 minute intervals(snooze function). A text memo can also bedisplayed for the alarm. A total of 3 separatealarm times can be programmed for eachhandset. You can set one of 3 different alarmoptions (once, daily, or weekly) for each alarmtime.Important:R Make sure the unit’s date and time setting

is correct (page 14).

1 MMENUN#7202 MbN: Select the desired alarm. a

MSELECTN3 MbN: Select the desired alarm option. a

MSELECTN

“Off”Turns alarm off. Go to step 10.“Once”An alarm sounds once at the set time.“Daily”An alarm sounds daily at the set time.Go to step 5.“Weekly”Alarm sounds weekly at the set time(s).

4 Proceed with the operation according toyour selection in step 3.n Once:

Enter the desired month and date. aMOKN

n Weekly:MbN: Select the desired day of the weekand press MSELECTN. a MOKN

5 Set the desired time.6 *: Select “AM” or “PM”. a MOKN7 Enter a text memo (10 characters max.).

a MOKN

8 MbN: Select the desired alarm tone. aMSELECTNR We recommend selecting a different

ringer tone from the one used foroutside calls.

9 MbN: Select the desired snooze setting.a MSAVEN

10 MSELECTN a MOFFNNote:R Press MSTOPN to stop the alarm completely.R When the handset is in use, the alarm will

not sound until the handset is in standbymode.

R Press any dial key or MSNOOZEN to stopthe sound but keep the snooze functionactivated.

R If you want to make an outside call whenthe snooze function is activated, pleasestop the snooze function before making thecall.

Silent modeSilent mode allows you to select a period oftime during which the handset and/or baseunit will not ring for outside calls. This featureis useful for time periods when you do notwant to be disturbed, for example, whilesleeping. Silent mode can be set for each unit.Using the phonebook’s group feature(page 25), you can also select groups ofcallers whose calls override silent mode andring the unit (Caller ID subscribers only).Important:R Make sure the unit’s date and time setting

is correct (page 14).R We recommend turning the base unit ringer

off (page 17) in addition to turning the silentmode on. (KX-TGE430 series: page 3)

R If you have set the alarm, the alarm soundseven if the silent mode is turned on.

Turning silent mode on/off1 For handset setting: MMENUN#238



Programming

TGE43xUS(en)_1112_ver021.pdf 34 2015/11/12 10:12:57

2 MbN: Select the desired setting. aMSAVENR If you select “Off”, press MOFFN to

exit.3 Enter the desired hour and minute you

wish to start this feature.4 *: Select “AM” or “PM”. a MOKN5 Enter the desired hour and minute you

wish to end this feature.6 *: Select “AM” or “PM”.7 MSAVEN a MOFFN*1 KX-TGE440 series: page 3

Changing the start and end time1 For handset setting: MMENUN#237


2 Continue from step 3, “Turning silentmode on/off”, page 34.


Selecting groups to bypass silentmode1 For handset setting: MMENUN#241


2 MbN: Select the desired groups. aMSELECTNR “ ” is displayed next to the selected

group numbers.R To cancel the selected group:MbN: Select the group. a PressMSELECTN again. “ ” disappears.

3 MSAVEN a MOFFN*1 KX-TGE440 series: page 3

Baby monitorThis feature allows you to listen in on a roomwhere another handset is located, allowingyou to easily monitor from different areas ofthe house or even while away from home. Themonitored handset (placed in a baby’s room,for example) will automatically call the

monitoring handset, base unit, or the phonenumber stored when it detects sound.Important:R Before using this feature, we recommend

that you test this feature and adjust thebaby monitor sensitivity as needed,especially if you plan to monitor fromoutside.

R This feature should not be used as asubstitute for a medical or caregiver’ssupervision. It is the caregiver’sresponsibility to stay close enough tohandle any eventuality.

Note:R If the unit is connected to a PBX system,

you cannot set the baby monitor.R During the monitoring mode, battery

consumption is faster than usual. Werecommend leaving the monitored handseton the base unit or charger.

R The monitored handset never rings while itis being monitored. If the base unit isplaced near the monitored handset, werecommend turning off the base unit ringervolume (page 17).

Setting the baby monitorPerform the setting operation with the handsetto be monitored (for example, the handsetplaced in a baby’s room).

To monitor with a unitThe internal baby monitor feature is available:– between handsets– between a handset and the base unit*1*1 KX-TGE440 series: page 3

1 MMENUN#2682 MbN: “On” a MSELECTN3 MbN: Select the desired unit’s number to

monitor with. a MSAVENR “Baby monitor” will be displayed.R The registered unit’s name/number is

displayed.


Programming

TGE43xUS(en)_1112_ver021.pdf 35 2015/11/12 10:12:57

Note:R When this feature is on, another handset or

the base unit can hear the monitoredhandset by making an intercom call.

To monitor from outsideIf you enable this feature, the unit will call apre-programmed phone number when thehandset detects sound. After you answer thecall, you can listen in on the room where thehandset is located.n From the phonebook:

1 MMENUN#2682 MbN: “On” a MSELECTN3 MbN: Select “Outgoing call” to

monitor from outside. a MADDN4 MbN: “Phonebook” a MSELECTN5 MbN: Select the phonebook entry. a

MSAVENR “Baby monitor” will be displayed.

Note:R If you edit a phonebook entry which is

assigned for monitoring, the edited entrydoes not transfer to the monitor.

n By entering phone numbers:1 MMENUN#2682 MbN: “On” a MSELECTN3 MbN: Select “Outgoing call” to

monitor from outside. a MADDN4 MbN: “Manual” a MSELECTN5 Enter the desired name. a MOKN6 Enter the desired number. a MOKN

a MSELECTNR “Baby monitor” will be displayed.

Note:R The registered name/number is displayed.

Turning off the baby monitorThe monitored handset cannot be used whilebaby monitor is set to “On”.1 Press MMENUN on the handset being

monitored.2 MbN: “On/Off” a MSELECTN

3 MbN: “Off” a MSELECTN a MOFFN

Editing an outside monitoring number1 Press MMENUN on the handset being

monitored.2 MbN: “On/Off” a MSELECTN3 MbN: “On” a MSELECTN4 MbN: Select the outside line.5 MMENUN a MbN: “Edit” a MSELECTN6 Edit the name if necessary. a MOKN7 Edit the phone number if necessary. a

MOKN a MSELECTN

Erasing an outside monitoringnumber1 Press MMENUN on the handset being

monitored.2 MbN: “On/Off” a MSELECTN3 MbN: “On” a MSELECTN4 MbN: Select the outside line.5 MMENUN a MbN: “Erase” a MSELECTN6 MbN: “Yes” a MSELECTN a MOFFN

Baby monitor sensitivityYou can adjust the sensitivity of the babymonitor. Increase or decrease the sensitivity toadjust the sound level needed to trigger thebaby monitor feature.R This feature cannot be set during a

monitoring call.1 Press MMENUN on the handset being

monitored.2 MbN: “Sensitivity level” a

MSELECTN3 MbN: Select the desired setting. a

MSAVEN a MOFFN


Programming

TGE43xUS(en)_1112_ver021.pdf 36 2015/11/12 10:12:57

Answering the baby monitorn When monitoring with a unit:

Handset: Press M N to answer a call.Base unit: Press M N to answer a call*1.*1 KX-TGE440 series: page 3

If you want to respond from the monitoringunit, press MMUTEN.R The monitoring unit will answer calls

automatically when the auto intercomfeature is set to “On” (page 21).

Note:R If you receive an outside call when

communicating with the monitored handset,the interrupt tone sounds.– To answer the call with the handset,

press MOFFN, then press M N.– To answer the call with the base unit,

press MZN 3 times.*1*1 If MMUTEN is pressed, press MZN 2

times.n When monitoring from outside:

Answer the call.If you want to respond from your monitoringphone, press #1 using tone dialing.You can turn off the baby monitor featureby pressing #0.

Note:R The unit disconnects the call automatically

after 2 minutes.

Other programming

Changing the handset nameThe default handset name is “Handset 1” to“Handset 6”. You can customize the nameof each handset (“Bob”, “Kitchen”, etc.). This isuseful when you make intercom calls betweenhandsets. To display the handset name instandby mode, turn on the handset namedisplay feature (page 37).1 MMENUN#1042 Enter the desired name (10 characters

max.). a MSAVEN a MOFFN

Displaying the handset nameYou can select whether or not the handsetname is displayed in standby mode. Thedefault setting is “Off”.1 MMENUN#1052 MbN: Select the desired setting. a

MSAVEN a MOFFN

Registering a unit

Operating additional units

Additional handsetsUp to 6 handsets can be registered to thebase unit.Important:R See page 5 for information on the available

model.

Registering a handset to thebase unitThe supplied handset and base unit arepre-registered. If for some reason the handsetis not registered to the base unit, re-registerthe handset.1 Handset:

MMENUN#1302 Base unit:

Press and hold MLOCATORN orMHANDSET LOCATORN for about 5seconds.R If all registered handsets start ringing,

press MLOCATORN or MHANDSETLOCATORN again to stop, then repeatthis step.

3 Handset:Press MOKN, then wait until a long beepsounds.


Programming

TGE43xUS(en)_1112_ver021.pdf 37 2015/11/12 10:12:57

Deregistering a handsetA handset can cancel its own registration tothe base unit, or other handsets registered tothe same base unit. This allows the handset toend its wireless connection with the system.1 MMENUN#131

R All handsets registered to the base unitare displayed.

2 MbN: Select the handset you want tocancel. a MSELECTN

3 MbN: “Yes” a MSELECTN a MOFFN


Programming

TGE43xUS(en)_1112_ver021.pdf 38 2015/11/12 10:12:57

Using Caller ID serviceImportant:R This unit is Caller ID compatible. To use

Caller ID features, you must subscribe to aCaller ID service. Contact your phoneservice provider for details.

Caller ID featuresWhen an outside call is being received, thecaller information is displayed.Caller information for the last 50 callers islogged in the caller list from the most recentcall to the oldest.R If the unit cannot receive caller information,

the following is displayed:– “Out of area”: The caller dials from

an area which does not provide a CallerID service.

– “Private caller”: The callerrequests not to send caller information.

– “Long distance”: The caller makes along distance call.

R If the unit is connected to a PBX system,caller information may not be properlyreceived. Contact your PBX supplier.

Missed callsIf a call is not answered, the unit treats it as amissed call. The display shows “Missedcall”.Note:R Even when there are unviewed missed

calls, “Missed call” disappears from thestandby display if the following operation isperformed by one of the units:– A handset is replaced on the base unit

or charger.– Pressing MOFFN on a handset.

Phonebook name displayWhen caller information is received and itmatches a phone number stored in thephonebook, the stored name in thephonebook is displayed and logged in thecaller list.

Talking Caller IDHandset / Base unit

This feature lets you know who is callingwithout looking at the display.To use this feature, you must:– subscribe to a Caller ID service of your

phone service provider.– turn this feature on (page 30).When caller information is received, thehandsets and/or base unit announce thecaller’s name or phone number received fromyour phone service provider following everyring.R Name pronunciation may vary. This feature

may not pronounce all names correctly.R Caller ID service has a limit of how many

characters can be displayed. If the caller’sname is too long, the unit may not be ableto display or announce the entire name.

Phonebook name announcementWhen caller information is received and itmatches a phone number stored in thephonebook, the stored name in thephonebook is announced.

Caller listImportant:R Make sure the unit’s date and time setting


Viewing the caller list and callingback1 MCN CID2 Press MCN to search from the most recent

call, or MDN to search from the oldest call.3 To call back, press M N.

To exit, press MOFFN.Note:R If the entry has already been viewed or

answered, “ ” is displayed.


Caller ID Service

TGE43xUS(en)_1112_ver021.pdf 39 2015/11/12 10:12:57

Editing a caller’s phone numberYou can edit a phone number in the caller listby removing its area code and/or the longdistance code “1”.1 MCN CID2 MbN: Select the desired entry. a MMENUN3 MbN: “Edit” a MSELECTN4 Press MEDITN repeatedly until the phone

number is shown in the desired format.5 M N

Caller ID number auto edit featureOnce you call back an edited number, the unitwhich was used to call back remembers thearea code and format of the edited number.The next time someone calls from the samearea code, caller information is customized bythe unit as follows:– When the call is being received, the Caller

ID number is displayed in the same formatas the edited number.

– After the call has ended, the caller’s phonenumber is displayed in the same format asthe edited number, when reviewed from thecaller list.

For example, you can use this feature to setthe unit to ignore the area code of callers inyour area, so that you can call these localnumbers using caller information withoutdialing the area code.To activate this feature, you must edit an entryin the caller list, then call that number. Afterthat, phone numbers from that caller’s areacode are edited automatically.This feature can be set for each unit(page 32). The default setting is “On”.Note:R Phone numbers from the 4 most recently

edited area codes are automatically edited.

Erasing selected callerinformation1 MCN CID2 MbN: Select the desired entry.

3 MERASEN a MbN: “Yes” a MSELECTNa MOFFN

Erasing all caller information1 MCN CID2 MERASEN a MbN: “Yes” a MSELECTN

a MOFFN


Caller ID Service

TGE43xUS(en)_1112_ver021.pdf 40 2015/11/12 10:12:57

Answering systemThe answering system can answer and recordcalls for you when you are unavailable toanswer the phone.You can also set the unit to play a greetingmessage but not to record caller messages byselecting “Greeting only” as the recordingtime setting (page 46).Important:R Make sure the unit’s date and time setting


Memory capacity (including yourgreeting message)The total recording capacity is about 17minutes. A maximum of 64 messages can berecorded.Note:R When message memory becomes full:

– “Messages full” is shown on thehandset display.

– The message counter on the base unitflashes if the answering system is turnedon.

– If you use the pre-recorded greetingmessage, the unit automatically switchesto another pre-recorded greetingmessage asking callers to call againlater.

– If you recorded your own greetingmessage, the same message is stillannounced to callers even though theirmessages are not recorded.

Turning the answeringsystem on/off

Base unitPress MANSWER ON/OFFN to turn on/off theanswering system.

Handset

1 To turn on:MMENUN#327

To turn off:MMENUN#328

2 MOFFNNote for base unit and handset:R When the answering system is turned on,

the message counter on the base unitdisplays the total number of messages (oldand new).

Greeting messageWhen the unit answers a call, a greetingmessage is played to callers.You can use either:– your own greeting message– a pre-recorded greeting message

Recording your greeting message1 MMENUN#3022 MbN: “Yes” a MSELECTN3 After a beep sounds, hold the handset

about 20 cm (8 inches) away and speakclearly into the microphone (2 minutesmax.).

4 Press MSTOPN to stop recording. aMOFFN

Using a pre-recorded greetingmessageThe unit provides 2 pre-recorded greetingmessages:– If you reset to pre-recorded greeting or do

not record your own greeting message, theunit plays a pre-recorded greeting askingcallers to leave a message.

– If the message recording time (page 46)is set to “Greeting only”, callers’messages are not recorded and the unitplays a different pre-recorded greetingmessage asking callers to call again.


Answering System

TGE43xUS(en)_1112_ver021.pdf 41 2015/11/12 10:12:57

Resetting to a pre-recorded greetingmessageUse this procedure to erase your greetingmessage and use a pre-recorded one.1 MMENUN#3042 MYESN a MOFFN

Playing back the greetingmessage1 MMENUN#3032 To exit, press MOFFN.

Listening to messagesImportant:R When using the base unit or handset to

listen to messages, the noise reductionfeature (page 18) is activated automaticallyin spite of the setting ( is notdisplayed).

Using the base unitWhen new messages have been recorded,M N on the base unit flashes.Press M N (PLAY).R During playback, M N on the base unit

lights.R If new messages have been recorded, the

base unit plays back new messages.R If there are no new messages, the base

unit plays back all messages.

Operating the answering systemduring playback

Key OperationMjN or MkN Adjust the speaker

volumeM N Repeat message*1

M N Skip messageM N (STOP) Stop playback

Key OperationMERASEN Erase currently playing

message

*1 If pressed within the first 5 seconds of amessage, the previous message isplayed.

Erasing all messagesPress MERASEN 2 times while the unit is not inuse.

Using the handsetWhen new messages have been recorded:– “New message” is displayed.– The message indicator on the handset

flashes slowly if the message indicator isturned on (page 46).

1 To listen to new messages:MMENUN#323To listen to all messages:MMENUN#324

2 When finished, press MOFFN.Note:R To switch to the receiver, press M N.R You can also use the MPLAYN soft key, if

displayed, to play new messages.

Operating the answering systemMMENUN a MbN: “Answering device” aMSELECTN

Key OperationMjN or MkN Adjust the receiver/speaker

volume (during playback)1 or MFN Repeat message (during

playback)*1

2 or MEN Skip message (duringplayback)

3 Enter the “Settings” menu

4 Play new messages5 Play all messages6 Play greeting message


Answering System

TGE43xUS(en)_1112_ver021.pdf 42 2015/11/12 10:12:57

Key Operation76 Record greeting message8 Turn answering system onMPAUSEN Pause message*2

9 orMSTOPN

Stop recordingStop playback

0 Turn answering system off

*4*3 Erase currently playingmessage

*5 Erase all messages*6 Reset to a pre-recorded

greeting message


*2 To resume playback:MbN: “Playback” a MSELECTN

*3 You can also erase as follows:MPAUSEN a MbN: “Erase” aMSELECTN a MbN: “Yes” a MSELECTN

Calling back (Caller ID subscribersonly)1 Press MPAUSEN during playback.2 MbN: “Call back” a MSELECTN

Editing the number before calling back1 Press MPAUSEN during playback.2 MbN: “Edit & Call” a MSELECTN3 Press MEDITN repeatedly until the phone

number is shown in the desired format(page 40). a M N

Erasing all messages1 MMENUN#3252 MbN: “Yes” a MSELECTN a MOFFN

Advanced new messagealerting features

Audible message alertThis feature allows the base unit to beep toinform you of a new message arrival whennew messages are recorded. The base unitbeeps 2 times every minute until you listen tothe messages, if the “Base unit beep”setting is turned on. The default setting is“Off”.1 MMENUN#3392 MbN: Select the desired setting. a

MSAVEN a MOFFN

New message alert by a callThis feature allows you to receive anotification by phone when new messages arerecorded. The base unit calls a phone numberyou specify. You can then operate theanswering system remotely to listen to thenew message.To use this feature, you must:– store a phone number to which the unit

makes the call to.– turn on the new message alert setting.After you answer the new message alert call,you can listen to messages from that call(page 44).Important:R A new message alert is stopped 1 minute

after the unit starts to call. The unit will notretry the call even if the call is not answered.

Storing a phone number to which theunit makes an alert calln From the phonebook:

1 MMENUN#3382 MbN: “Notification to” a

MSELECTN a MADDN3 MbN: “Phonebook” a MSELECTN4 MbN: Select the desired phonebook

entry. a MSAVEN a MOFFN


Answering System

TGE43xUS(en)_1112_ver021.pdf 43 2015/11/12 10:12:57

n By entering a phone number:1 MMENUN#3382 MbN: “Notification to” a

MSELECTN a MADDN3 MbN: “Manual” a MSELECTN4 Enter the desired name (16 characters

max.). a MOKN5 Enter the desired number (24 digits

max.). a MOKN a MSELECTN aMOFFN

Turning on/off the new message alertsetting1 MMENUN#3382 MbN: “On/Off” a MSELECTN3 MbN: Select the desired setting. a

MSAVEN a MOFFN

Editing the set phone number1 MMENUN#3382 MbN: “Notification to” a MSELECTN3 MMENUN a MbN: “Edit” a MSELECTN4 Edit the name if necessary (16 characters

max.). a MOKN5 Edit the phone number if necessary (24

digits max.). a MOKN a MSELECTN aMOFFN

Erasing the set phone number1 MMENUN#3382 MbN: “Notification to” a MSELECTN3 MMENUN a MbN: “Erase” a MSELECTN4 MbN: “Yes” a MSELECTN a MOFFN

R The new message alert setting isturned off.

Activating/inactivating the remoteaccess code to play messagesIf you activate this feature, you must enter theremote access code (page 45) to play thenew message from the new message alertcall. This is so that unauthorized parties

cannot listen to your messages. The defaultsetting is “Inactivate”.– “Inactivate”: You can listen to the

message by pressing 4 to play newmessages (without entering the remoteaccess code).

– “Activate”: You must enter your remoteaccess code and then press 4 to play newmessage.

1 MMENUN#3382 MbN: “Remote code” a MSELECTN3 MbN: Select the desired setting. a

MSAVEN a MOFFN

Listening to messagesAfter you answer the new message alert, youcan listen to the messages as follows.n When the remote access code is set to

“Inactivate”:Press 4 to play the new message duringthe announcement.

n When the remote access code is set to“Activate”:1 Enter the remote access code

(page 45) during the announcement.2 Press 4 to play the new message.

Note:R Within 10 seconds after listening to new

messages, you can press #9 during thecall to turn off the new message alert by acall feature.

R Even if the unit makes a new message alertcall, the handset redial list does not showthe record.

Remote operationUsing a touch-tone phone, you can call yourphone number from outside and access theunit to listen to messages or changeanswering system settings. The unit’s voiceguidance prompts you to press certain dialkeys to perform different operations.


Answering System

TGE43xUS(en)_1112_ver021.pdf 44 2015/11/12 10:12:57

Remote access codeA 3-digit remote access code must be enteredwhen operating the answering systemremotely. This code prevents unauthorizedparties from listening to your messagesremotely. The default setting is “111”.Important:R To prevent unauthorized access to this

product, we recommend that you regularlychange the remote code.

1 MMENUN#3062 Enter the desired 3-digit remote access

code. a MSAVEN a MOFFN

Deactivating remote operationPress * in step 2 on “Remote access code”,page 45.R The entered remote access code is deleted.

Using the answering systemremotely1 Dial your phone number from a

touch-tone phone.2 After the greeting message starts, enter

your remote access code.3 Follow the voice guidance prompts as

necessary or control the unit usingremote commands (page 45).

4 When finished, hang up.

Voice guidancen When the English voice guidance is

selectedDuring remote operation, the unit’s voiceguidance starts and prompts you to press1 to perform a specific operation, or press2 to listen to more available operations.

n When the Spanish voice guidance isselectedTo start the voice guidance, press 9. Thevoice guidance announces the availableremote commands (page 45).

Note:R If you do not press any dial keys within 10

seconds after a voice guidance prompt, theunit disconnects your call.

Remote commandsYou can press dial keys to access certainanswering system functions without waiting forthe voice guidance to prompt you.

Key Operation1 Repeat message (during

playback)*1

2 Skip message (during playback)4 Play new messages5 Play all messages9 Stop playback*2

Start voice guidance*3

0 Turn answering system off*4 Erase currently playing message*5 Erase all messages*# End remote operation

(or hang up)


*2 For English voice guidance only*3 For Spanish voice guidance only

Turning on the answering systemremotely1 Dial your phone number from a

touch-tone phone.2 Let the phone ring 15 times.

R A long beep is heard.3 Enter your remote access code within 10

seconds after the long beep.R The greeting message is played back.R You can either hang up, or enter your

remote access code again and beginremote operation (page 44).


Answering System

TGE43xUS(en)_1112_ver021.pdf 45 2015/11/12 10:12:57

Answering system settings

Call screeningHandset / Base unit

While a caller is leaving a message, you canlisten to the call through the unit’s speaker.To adjust the speaker volume, press MjN orMkN repeatedly.You can answer the call by pressing M N onthe handset or MZN on the base unit*1.Call screening can be set for each unit. Thedefault setting is “On”.1 For handset setting: MMENUN#310


2 MbN: Select the desired setting. aMSAVEN a MOFFN


Number of rings before the unitanswers a callYou can change the number of times thephone rings “Ring count” before the unitanswers calls. You can select 2 to 7 rings, or“Toll saver”.The default setting is “4 rings”.“Toll saver”: The unit’s answering systemanswers at the end of the 2nd ring when newmessages have been recorded, or at the endof the 5th ring when there are no newmessages. If you call your phone from outsideto listen to new messages (page 45), youknow that there are no new messages whenthe phone rings for the 3rd time. You can thenhang up without being charged for the call.1 MMENUN#2112 MbN: Select the desired setting. a

MSAVEN a MOFFN

Caller’s recording timeYou can change the maximum messagerecording time allowed for each caller. Thedefault setting is “3 min”.

1 MMENUN#3052 MbN: Select the desired setting. a

MSAVEN a MOFFN

Selecting “Greeting only”You can select “Greeting only” which setsthe unit to announce a greeting message tocallers but not record messages.Select “Greeting only” in step 2 on“Caller’s recording time”, page 46.Note:R When you select “Greeting only”:

– If you do not record your own message,the unit will play the pre-recordedgreeting-only message asking callers tocall again later.

– If you use your own message, record thegreeting-only message asking callers tocall again later (page 41).

Handset message indicatorYou can select whether or not the messageindicator on the handset flashes slowly whennew messages are recorded. The defaultsetting is “On”.Important:R If you stored the voicemail access number

(page 47), the message indicator alsoflashes for newly recorded voicemailmessages (page 48).

1 MMENUN#3402 MbN: Select the desired setting. a

MSAVEN a MOFFNNote:R While message indicator is on, battery

operating time is shortened (page 11).


Answering System

TGE43xUS(en)_1112_ver021.pdf 46 2015/11/12 10:12:57

Voicemail serviceIn addition to your unit’s answering systemyou may also have voicemail service fromyour phone service provider. Voicemail isan answering service that may be offered byyour phone service provider. This service canalso record calls when you are unavailable toanswer the phone or when your line is busy.Messages are recorded on the phonecompany system and not on the unit’sanswering system.R To use the voicemail service rather than the

unit’s answering system, turn off theanswering system (page 41).

If you have unit’s answering system set to onand also the voicemail enabled, the systemwith least amount of rings will record themessage first.Example:If the unit’s answering system is set to 4 rings(page 46) and the voicemail answering systemprovided by your phone company is set to 6rings (call your service provider), the unit’sanswering system will record the incoming callfirst.Important:R You need to store the voicemail access

number to activate the message indicator(page 46) for voicemail service.

Storing the voicemail (VM)access numberIn order to listen to your voicemail messages,you must dial your phone service provider’svoicemail access number. Once you havestored your voicemail access number, you candial it automatically (page 48).1 MMENUN#3312 Enter your access number (24 digits

max.). a MSAVEN a MOFFNNote:R When storing your voicemail access

number and your mailbox password, pressMDN (Pause) to add pauses (page 16)between the access number and thepassword as necessary. Contact your

phone service provider for the requiredpause time.

Example:

1-222-333-4444

VM access number

Pauses Password

PPPP 8888

To erase the voicemail access number1 MMENUN#3312 Press and hold MCLEARN until all digits

are erased. a MSAVEN a MOFFN

Voicemail (VM) tone detectionHandset / Base unit*1


Your phone service provider sends specialsignals (sometimes called “voicemail tones” or“stutter tones”) to the unit to let you know youhave new voicemail messages. If you hear aseries of dial tones followed by a continuousdial tone after you press M N on the handsetor press MZN on the base unit, you have newvoicemail messages. Soon after you hang upa call or after the phone stops ringing, yourunit checks the phone line to see if newvoicemail messages have been recorded.Turn this feature off when:– You do not subscribe to voicemail service.– Your phone service provider does not send

voicemail tones.– Your phone is connected to a PBX.If you are not sure which setting is required,contact your phone service provider.

Turning VM tone detection on/offThe default setting is “On”.1 MMENUN#3322 MbN: Select the desired setting. a

MSAVEN a MOFFN


Useful Information

TGE43xUS(en)_1112_ver021.pdf 47 2015/11/12 10:12:57

Listening to voicemail messagesWhen new messages have been recorded:– “Voicemail msg. via phone co.” is

displayed if message indication service isavailable.

– The message indicator on the handsetflashes slowly if the message indicator isturned on (page 46).

Handset

1 MMENUN#330R The speakerphone turns on.

2 Follow the pre-recorded instructions.3 When finished, hang up.Note:R You can also use the MACCESSN soft key,

if displayed, to play new voicemailmessages.

R If the handset still indicates there are newmessages even after you have listened toall new messages, turn it off by pressingand holding # until the handset beeps.

Base unit*1


To listen to voicemail messages, you have todial your voicemail access number manually.

Wall mountingNote:R Make sure that the wall and the fixing

method are strong enough to support theweight of the unit.

Base unit1 Lead the AC adaptor cord and telephone

line cord through the hole in the wallmounting adaptor in the direction of thearrow.

2 Tuck the telephone line cord inside thewall mounting adaptor (A). Connect theAC adaptor cord and telephone line cord(B).1 AC adaptor cord

A

B

1


Useful Information

TGE43xUS(en)_1112_ver021.pdf 48 2015/11/12 10:12:57

3 Insert the hooks on the wall mountingadaptor into holes (1) and (2) on thebase unit.

1 2

12

4 Adjust the adaptor to hold the base unit,then push it in the direction of the arrowuntil it clicks into place.

5 Mount the unit on a wall then slide downto secure in place.1 AC adaptor cordR This product is compliant with the

following wall phone plate sizes (2types).2 83 mm (3 1/4 inches)3 102 mm (4 inches)Fit the slots of the unit onto thecorresponding wall phone plate tabsfor (4) and (5) respectively.

1

5

4

2 3

4

5


Useful Information

TGE43xUS(en)_1112_ver021.pdf 49 2015/11/12 10:12:57

To remove the wall mounting adaptorWhile pushing down the release levers (A),remove the adaptor (B).

B

A A

ChargerDrive the screws (1) (not supplied) into thewall.2 27.2 mm (1 1/16 inches)

1

2


Useful Information

TGE43xUS(en)_1112_ver021.pdf 50 2015/11/12 10:12:57

Error messagesDisplay message Cause/solutionAsk phonecompany forVM access #

R You have not stored the voicemail access number. Store thenumber (page 47).

Base no powerorNo link. Re-connect baseAC adaptor.orNo link.

R Confirm the base unit’s AC adaptor is connected to the unitand the power outlet correctly.

R The handset has lost communication with the base unit. Movecloser to the base unit and try again.

R Unplug the base unit’s AC adaptor to reset the unit.Reconnect the adaptor and try again.

R The handset’s registration may have been canceled.Re-register the handset (page 37).

R When “No link.” is displayed during a power failure, placea handset on the base unit to supply power to the base unit.

Busy R The called unit is in use.R Other units are in use and the system is busy. Try again later.R The handset you are using is too far from the base unit. Move

closer and try again.Check tel line R The supplied telephone line cord has not been connected yet

or not connected properly. Check the connections (page 10).Error!! R Recording was too short. Try again.Invalid R There is no handset registered to the base unit matching the

handset number you entered.R The handset is not registered to the base unit. Register the

handset (page 37).Requiressubscriptionto Caller ID.

R You must subscribe to a Caller ID service. Once you receivecaller information after subscribing to a Caller ID service, thismessage will not be displayed.

Userechargeablebattery.

R A wrong type of battery such as alkaline or manganese wasinserted. Use only the rechargeable Ni-MH batteries noted onpage 4, 7.


Useful Information

TGE43xUS(en)_1112_ver021.pdf 51 2015/11/12 10:12:57

TroubleshootingIf you still have difficulties after following the instructions in this section, disconnect the base unit’sAC adaptor, then reconnect the base unit’s AC adaptor. Remove the batteries from the handset,and then insert them into the handset again.

General use

Problem Cause/solutionThe handset does not turn oneven after installing chargedbatteries.

R Place the handset on the base unit or charger to turn onthe handset.

The unit does not work. R Make sure the batteries are installed correctly (page 10).R Fully charge the batteries (page 11).R Check the connections (page 10).R Unplug the base unit’s AC adaptor to reset the unit.

Reconnect the adaptor and try again.R The handset has not been registered to the base unit.

Register the handset (page 37).I cannot hear a dial tone. R The base unit’s AC adaptor or telephone line cord is not

connected. Check the connections.R Disconnect the base unit from the telephone line and

connect the line to a known working telephone. If theworking telephone operates properly, contact our servicepersonnel to have the unit repaired. If the workingtelephone does not operate properly, contact your phoneservice provider.

The indicator on the handsetflashes slowly.

R New messages have been recorded. Listen to the newmessages (page 42).

R New voicemail messages have been recorded. Listen tothe new voicemail messages (page 48).

The base unit beeps. R New messages have been recorded. Listen to the newmessages (page 42).

Menu list

Problem Cause/solutionThe display is in a language Icannot read.

R Change the display language (page 14).

I cannot register a handset to abase unit.

R The maximum number of handsets (6) is alreadyregistered to the base unit. Cancel unused handsetregistrations from the base unit (page 38).


Useful Information

TGE43xUS(en)_1112_ver021.pdf 52 2015/11/12 10:12:58

Battery recharge

Problem Cause/solutionThe handset beeps and/or flashes.

R Battery charge is low. Fully charge the batteries (page 11).

I fully charged the batteries, but– still flashes,– is displayed, or– the operating time seems to

be shorter.

R Clean the battery ends ( , ) and the charge contactswith a dry cloth and charge again.

R It is time to replace the batteries (page 10).

Making/answering calls, intercom

Problem Cause/solution is displayed. R The handset is too far from the base unit. Move closer.

R The base unit’s AC adaptor is not properly connected.Reconnect AC adaptor to the base unit.

R The handset is not registered to the base unit. Register it(page 37).

Noise is heard, sound cuts inand out.

R You are using the handset or base unit in an area withhigh electrical interference. Re-position the base unit anduse the handset away from sources of interference.

R Move closer to the base unit.R If you use a DSL/ADSL service, we recommend

connecting a DSL/ADSL filter between the base unit andthe telephone line jack. Contact your DSL/ADSL providerfor details.

The handset does not ring. R The ringer volume is turned off. Adjust the ringer volume(page 17, 30).

R Silent mode is turned on. Turn it off (page 34).The base unit does not ring. R The ringer volume is turned off. Adjust the ringer volume

(page 17).R Silent mode is turned on. Turn it off (page 34).

I cannot make a call. R The dialing mode may be set incorrectly. Change thesetting (page 15).

I cannot make or answer a call. R An outside line is being used after a cell locator feature isused.– KX-TGE430 series: To end the call, press MLOCATES

CELLN on the base unit.– KX-TGE440 series: To end the call if someone

answers using the cellular phone, press MZN on thebase unit.

I cannot make long distancecalls.

R Make sure that you have long distance service.


Useful Information

TGE43xUS(en)_1112_ver021.pdf 53 2015/11/12 10:12:58

Problem Cause/solutionI cannot use voice paging. R You cannot use voice paging if other units are in use.

R Voice paging is not available when a range extender(KX-TGA405) is registered to the base unit.

Caller ID/Talking Caller ID

Problem Cause/solutionCaller information is notdisplayed.

R You must subscribe to Caller ID service. Contact yourphone service provider for details.

R If your unit is connected to any additional telephoneequipment such as a Caller ID box or cordless telephoneline jack, plug the unit directly into the wall jack.

R If you use a DSL/ADSL service, we recommendconnecting a DSL/ADSL filter between the base unit andthe telephone line jack. Contact your DSL/ADSL providerfor details.

R The name display service may not be available in someareas. Contact your phone service provider for details.

R Other telephone equipment may be interfering with thisunit. Disconnect the other equipment and try again.

Caller information is displayedor announced late.

R Depending on your phone service provider, the unit maydisplay or announce the caller’s information at the 2ndring or later.

R Move closer to the base unit.Caller information is notannounced.

R The handset or base unit’s ringer volume is turned off.Adjust it (page 17, 30).

R The Talking Caller ID feature is turned off. Turn it on(page 30).

R The number of rings for the answering system is set to “2rings” or “Toll saver”. Select a different setting(page 46).

R If the base unit and another handset are having anintercom call, your handset does not announce callerinformation.

The caller list/incoming phonenumbers are not editedautomatically.

R The Caller ID number auto edit feature is turned off. Turnit on and try again (page 32).

R You need to call back the edited number to activate CallerID number auto edit.

I cannot dial the phone numberedited in the caller list.

R The phone number you dialed might have been editedincorrectly (for example, the long distance “1” or the areacode is missing). Edit the phone number with anotherpattern (page 40).

Time on the unit has shifted. R Incorrect time information from incoming Caller IDchanges the time. Set the time adjustment to “Manual”(off) (page 30).


Useful Information

TGE43xUS(en)_1112_ver021.pdf 54 2015/11/12 10:12:58

Problem Cause/solutionThe 2nd caller’s information isnot displayed during an outsidecall.

R In order to use Caller ID, call waiting, or Call WaitingCaller ID (CWID), you must first contact your phoneservice provider and subscribe to the desired service.After subscribing, you may need to contact your phoneservice provider again to activate this specific service,even if you already subscribed to both Caller ID and CallWaiting with Caller ID services (CWID).

Answering system

Problem Cause/solutionThe unit does not record newmessages.

R The answering system is turned off. Turn it on (page 41).R The message memory is full. Erase unnecessary

messages (page 42, 43).R The recording time is set to “Greeting only”. Change

the setting (page 46).R Your phone service provider’s voicemail service may be

answering your calls before the unit’s answering systemcan answer your calls. Change the unit’s number of ringssetting (page 46) to a lower value, or contact your phoneservice provider.

R The answering system will not answer incoming callswhile the other devices such as handsets are engaged ina call.

I cannot operate the answeringsystem remotely.

R The remote access code is not set. Set the remoteaccess code (page 45).

R You are entering the wrong remote access code. If youhave forgotten your remote access code, enter theremote access code setting to check your current code(page 45).

R The answering system is turned off. Turn it on (page 45).The unit does not emit thespecified number of rings.

R If the first ring is turned off (“No”) (page 24), the numberof rings decreases by 1 from the specified number ofrings.


Useful Information

TGE43xUS(en)_1112_ver021.pdf 55 2015/11/12 10:12:58

Voicemail

Problem Cause/solution“Voicemail msg. viaphone co.” is shown on thehandset display.How do I remove this messagefrom the display?

R This notification is displayed when your phone serviceprovider’s voicemail service (not the unit’s answeringsystem) has recorded a message for you. Typically youcan remove this notification from the display by listeningto the message. To listen to the message, dial thevoicemail number provided by your phone serviceprovider (for most cases, this will be your own phonenumber), and follow the voice instructions. Depending onyour phone service provider, you may need to remove allmessages from your voice mailbox to remove thenotification. You can also remove this notification bypressing and holding # until the unit beeps.

Liquid damage

Problem Cause/solutionLiquid or other form of moisturehas entered the handset/baseunit.

R Disconnect the AC adaptor and telephone line cord fromthe base unit. Remove the batteries from the handset andleave to dry for at least 3 days. After the handset/baseunit are completely dry, reconnect the AC adaptor andtelephone line cord. Insert the batteries and charge fullybefore use. If the unit does not work properly, contact anauthorized service center.

Caution:R To avoid permanent damage, do not use a microwave oven to speed up the drying process.


Useful Information

TGE43xUS(en)_1112_ver021.pdf 56 2015/11/12 10:12:58

FCC and other informationThis equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US:ACJ----------.If requested, this number must be provided to the telephone company.L Registration No.............(found on the

bottom of the unit)L Ringer Equivalence No. (REN).......0.1B

A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with the product. It is designed to be connected to a compatible modular jack that is also compliant.

The REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for the product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3).

If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the customer as soon as possible. Also, you will be

advised of your right to file a complaint with the FCC if you believe it is necessary.

The telephone company may make changes in its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.

If trouble is experienced with this equipment, for repair or warranty information, please contact a Factory Service Center or other Authorized Servicer. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved.

Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.

If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.

This equipment is hearing aid compatible as defined by the FCC in 47 CFR Section 68.316.

When you hold the phone to your ear, noise might be heard in your Hearing Aid. Some Hearing Aids are not adequately shielded from external RF (radio frequency) energy. If noise occurs, use an optional headset accessory or the speakerphone option (if applicable) when using this phone. Consult with your audiologist or Hearing Aid


Useful Information

TGE43xUS(en)_1112_ver021.pdf 57 2015/11/12 10:12:58

manufacturer about the availability of Hearing Aids which provide adequate shielding to RF energy commonly emitted by digital devices.

WHEN PROGRAMMING EMERGENCYNUMBERS AND(OR) MAKING TESTCALLS TO EMERGENCY NUMBERS:1) Remain on the line and briefly explain to

the dispatcher the reason for the call.2) Perform such activities in the off-peak

hours, such as early morning or late evenings.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Privacy of communications may not be ensured when using this phone.

CAUTION:Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device.

NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. Thisequipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined byturning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:– Reorient or relocate the receiving

antenna.– Increase the separation between the

equipment and receiver.– Connect the equipment into an outlet on a

circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

Some cordless telephones operate at frequencies that may cause interference to nearby TVs and VCRs. To minimize or prevent such interference, the base of the cordless telephone should not be placed near or on top of a TV or VCR. If interference is experienced, move the cordless telephone further away from the TV or VCR. This will often reduce or eliminate interference.

FCC RF Exposure Warning:L This product complies with FCC radiation

exposure limits set forth for an uncontrolled environment.

L To comply with FCC RF exposure requirements, the base unit must be installed and operated 20 cm (8 inches) or more between the product and all person’s body.

L This product may not be collocated or operated in conjunction with any other antenna or transmitter.

L The handset may be carried and operated with only the specific provided belt-clip. Other non-tested belt-clips or similar body-worn accessories may not comply and must be avoided.

Notice:L FCC ID can be found inside the battery compartment or on the bottom of the

units.


Useful Information

TGE43xUS(en)_1112_ver021.pdf 58 2015/11/12 10:12:58

Compliance with TIA-1083 standard: Telephone handsets identified with this logo have reduced noise and interference when used with T-Coil equipped hearing aids and cochlear implants.

T

Compatible withHearing Aid T-Coil

TIA-1083


Useful Information

TGE43xUS(en)_1112_ver021.pdf 59 2015/11/12 10:12:58

Guía Rápida EspañolaConexiones

Unidad base

1 Conecte el adaptador de corriente alterna a la unidad presionándolo firmemente.2 Enganche el cable para fijarlo.3 Conecte el adaptador de corriente alterna a la toma de corriente.4 Conecte el cable de la línea telefónica a la unidad, y después a la toma telefónica de una sola línea

(RJ11C) hasta que escuche un clic.5 Se requiere un filtro DSL/ADSL (no incluido) si tiene este tipo de servicio.Nota:L Use solo el adaptador de corriente alterna Panasonic PNLV226 que se suministra.

1

4

5

3

4

2

Cargador

1 Conecte el adaptador de corriente alterna a la toma de corriente.

1

60 Para obtener ayuda, visite http://shop.panasonic.com/support (solo en inglés)

Guía Rápida Española

TGE43xUS(en)_1112_ver021.pdf 60 2015/11/12 10:12:58

Instalación y carga de la bateríaCargue aproximadamente durante 7 horas.

Nota:L UTILICE SOLO baterías recargables de Ni-MH tamaño AAA (R03) ( ).L NO utilice baterías alcalinas, de manganeso ni de Ni-Cd.L Confirme que las polaridades estén correctas (S, T).L Cambie el idioma de la pantalla.L Confirme que aparezca “Cargando” ( ).

Sugerencias de operaciónTeclas de funciónAl oprimir una tecla de función, puede seleccionar la función que aparece directamente encima de ella en la pantalla. Preste atención a la pantalla para ver qué funciones están asignadas a las teclas de función durante la operación.

Tecla de volumenOprima {+} o {-} repetidamente:- ajustar el volumen del timbre. - ajustar el volumen del receptor o del

altavoz mientras habla.

Tecla navegadora- {^}, {V}, {<}, o {>}: Navegue por diversas

listas y elementos.- v (Volumen: {^} o {V}): Ajuste el volumen

del receptor o el altavoz mientras habla.- {<} k: Vea la entrada del directorio

telefónico.- {>} REDIAL (Remarcación): Vea la lista de

remarcación.- {V} CID (identificador de llamadas): Vea la

lista de personas que llamaron.

KX-TGE430 KX-TGE440

1

2

1

2

{V}

{^}

{<} {>}

Para obtener ayuda, visite http://shop.panasonic.com/support (solo en inglés) 61


TGE43xUS(en)_1112_ver021.pdf 61 2015/11/12 10:12:58

Cambio de idiomas (Auricular) (predeterminado: “English”)Cuando instale las baterías por primera vez, es posible que aparezca “Set date/time Press SELECT”. Oprima {OFF} para salir.

Idioma de la pantalla{MENU}(11) s {r}: “Español” s {GUARDAR} s {OFF}

Idioma de anuncio de voz{MENU}(112 s {r}: “Español” s {GUARDAR} s {OFF}

Fecha y hora (Auricular)1 {MENU}(1)12 Introduzca el día, mes y año actuales. s {OK}3 Introduzca la hora y minuto actuales (formato de reloj de 24 horas).4 {GUARDAR} s {OFF}

Cómo grabar el mensaje de saludo del contestador de llamadas (Auricular)Puede grabar su propio mensaje de saludo en lugar de usar uno pregrabado.

1 {MENU}(3)2 s {r}: “Sí” s {SELEC.}2 Después de que se emita un pitido, sostenga el auricular a una distancia aproximada de

20 cm (8 pulgadas) y hable con claridad en el micrófono (máx. de 2 minutos).3 Oprima {PARAR} para dejar de grabar. s {OFF}

Operaciones básicasCómo hacer y contestar llamadas (Auricular)

Para hacer llamadas Marque el número telefónico. s {C}/{s}

Para contestar llamadas {C}/{s}

Para colgar {OFF}

Para ajustar el volumen del receptor o del altavoz

Oprima {+} o {-} repetidamente mientras habla.

Cómo hacer una llamada usando la lista de remarcación

{>} REDIAL s {r}: Seleccione el número telefónico deseado. s {C}

Para ajustar el volumen del timbre del auricular

Oprima {+} o {-} repetidamente para seleccionar el volumen deseado.



TGE43xUS(en)_1112_ver021.pdf 62 2015/11/12 10:12:58

Cómo hacer y contestar llamadas (unidad base: serie KX-TGE440)

Para hacer llamadas {s} s Marque el número telefónico.

Para contestar llamadas {s}

Para colgar {s}

Para ajustar el volumen del altavoz

Oprima {+} o {-} repetidamente mientras habla.

Remarcación del último número marcado

{s} s {REDIAL}

Para ajustar el volumen del timbre de la unidad base

Oprima {+} o {-} repetidamente para seleccionar el volumen deseado.

Directorio telefónico (Auricular)

Para añadir entradas 1 {<} k s {MENU}2 {r}: “Agregar Ent. Nueva” s {SELEC.}3 Introduzca el nombre de la persona (máx. 16 caracteres). s {OK}4 Introduzca el número telefónico de la persona (máx. 24 dígitos). s {OK}

5 {r}: Seleccione el grupo deseado. s {SELEC.} 2 veces s {OFF}L En el paso 3, puede cambiar el idioma de introducción de caracteres.( s {r}: Seleccione el idioma deseado. s {OK}

Para hacer llamadas {<} k s {r}: Seleccione la entrada deseada. s {C}

Sistema contestador de llamadas (Unidad base)

Contestador encendido/apagado

Oprima {ANSWER ON/OFF} para encender y apagar el contestador de llamadas.

Para escuchar mensajes {P} (PLAY)

Sistema contestador de llamadas (Auricular)

Para escuchar mensajes Para escuchar mensajes nuevos:{REPROD.} o {MENU}(323Para escuchar todos los mensajes:{MENU}(324

Operaciones básicas

Para obtener ayuda, visite http://shop.panasonic.com/support (solo en inglés) 63


TGE43xUS(en)_1112_ver021.pdf 63 2015/11/12 10:12:58

Preguntas frecuentesPregunta Causa y solución

¿Por qué aparece _? L El auricular está demasiado lejos de la unidad base. Acérquelo.L El adaptador para corriente de la unidad base no está conectado

correctamente. Conecte de nuevo el adaptador para corriente a la unidad base.

L El auricular no está registrado en la unidad base. Regístrelo.1 Auricular: {MENU}(13)2 Unidad base: Oprima y mantenga oprimido {LOCATOR} o {HANDSET LOCATOR} durante aproximadamente 5 segundos.

3 Auricular: Oprima {OK}, y después espere hasta que suene un pitido largo.

¿Cómo se incrementa el nivel de volumen del auricular?

L Oprima la tecla de volumen {+} repetidamente mientras habla.

¿Por qué hay ruido o se corta la conversación?

L Trate de reubicar la unidad base de forma que se minimice la distancia al auricular.

L Si ocurre el mismo problema aunque el auricular se encuentre enseguida de la unidad base,visite: http://shop.panasonic.com/support

¿Es posible añadir otro auricular accesorio a mi unidad base?

L Sí, puede añadir hasta 6 auriculares (incluyendo los que se venden con su unidad base) a una sola unidad base.

L Para adquirir auriculares accesorios adicionales (KX-TGEA40), visite: http://shop.panasonic.com/support Los usuarios TTY (usuarios con impedimentos auditivos o del habla) pueden llamar al 1-877-833-8855.

¿Es posible mantener cargando las baterías todo el tiempo?

L Puede dejar el auricular en la unidad base o el cargador en cualquier momento. Esto no daña las baterías.

¿Cómo se contestan las llamadas en espera (segunda llamada)?

L Oprima {CALL WAIT} cuando escuche el tono de llamada en espera.



TGE43xUS(en)_1112_ver021.pdf 64 2015/11/12 10:12:58

Customer services

Accessories!

h�p://shop.panasonic.com/support

Customer Services Directory

Shop

for all your Panasonic gearGo to

Get everything you need to get the most out of

your Panasonic products

Accessories & Parts for your Camera, Phone, A/V

products, TV, Computers & Networking, Personal

Care, Home Appliances, Headphones, Ba�eries,

Backup Chargers & more…

For Product Informa!on, Opera!ng Assistance,

Parts, Owner’s Manuals, Dealer and Service info

go to h�p://shop.panasonic.com/support

For the hearing or speech impaired TTY: 1- 877-833-8855

As of June 2015


Appendix

TGE43xUS(en)_1112_ver021.pdf 65 2015/11/12 10:12:58

Index# 3-way conference: 19A Additional handset: 37

Alarm: 34Answering calls: 17Answering system

Call screening: 46Erasing messages: 42, 43, 45Greeting message: 41Greeting only: 46Listening to messages: 42, 45New message alerting: 43Number of rings: 46Recording time: 46Remote access code: 45Remote operation: 44Ring count: 46Toll saver: 46Turning on/off: 41

Auto intercom: 21Auto talk: 17, 32

B Baby monitor: 35Battery: 10, 11Booster (Clarity booster): 18

C Call block: 23One ring for blocked call: 24

Call share: 19, 32Call waiting: 18Call Waiting Caller ID: 18Caller ID number auto edit: 32, 40Caller ID service: 39Caller list: 39Caller list edit: 40Cell locator: 20Chain dial: 26CID (Caller ID): 39Conference calls: 19Control type: 12Customer support: 32

D Date and time: 14Dialing mode: 15Direct command code: 28Display

Contrast: 31Language: 14

E Eco mode: 11Equalizer: 18Error messages: 51

F Flash: 18, 32G Groups: 25H Handset

Deregistration: 38Locator: 20Name: 37Registration: 37

Hold: 17I Intercom: 20K Key detector: 31, 33

Key tone: 32L Line mode: 32M Making calls: 16

Missed calls: 39Mute: 17

N Noise reduction: 18P Pause: 16

Phonebook: 25Power failure (power backupoperation): 21

R Redialing: 16Ringer ID: 26Ringer tone: 30Rotary/pulse service: 18

S Silent mode: 34Speed dial: 27SP-PHONE (Speakerphone): 16

T Talking Caller ID: 39Temporary tone dialing: 18Time adjustment: 30Transferring calls: 19Troubleshooting: 52TTY: 65

V VM (Voicemail): 47Voice announcement language: 14Voice paging: 20Voicemail: 47Volume

Receiver: 16Ringer (Base unit): 17Ringer (Handset): 17, 30Speaker: 16

W Wall mounting: 48

68

Index

TGE43xUS(en)_1112_ver021.pdf 68 2015/11/12 10:12:58

69

Notes

TGE43xUS(en)_1112_ver021.pdf 69 2015/11/12 10:12:58

70

Notes

TGE43xUS(en)_1112_ver021.pdf 70 2015/11/12 10:12:58

71

Notes

TGE43xUS(en)_1112_ver021.pdf 71 2015/11/12 10:12:58

1 Reconnect AC adaptor to the base unit.2 Check if telephone line cord is connected.3 Use rechargeable Ni-MH batteries. (Alkaline/Manganese/Ni-Cd batteries CANNOT be used.)4 Read troubleshooting page in the Operating Instructions.

Visit our Web site: http://shop.panasonic.com/supportL FAQ and troubleshooting hints are available.

If your product is not working properly. . .IMPORTANT!

For your future referenceWe recommend keeping a record of the following information to assist with any repair underwarranty.

Serial No. Date of purchase(found on the bottom of the base unit) Name and address of dealer

Attach your purchase receipt here.

Two Riverfront Plaza, Newark, NJ 07102-5490

© Panasonic System Networks Co., Ltd. 2015

Printed in Malaysia

*PNQX7786ZA**PNQX7786ZA*

PNQX7786ZA PP1115MG0

TGE43xUS(en)_1112_ver021.pdf 72 2015/11/12 10:12:58

Before initial use, see “Getting Started” on page 10. · 2 KX-TGE432 3 KX-TGE433 *4 KX-TG3634...

Documents

Transcript of Before initial use, see “Getting Started” on page 10. · 2 KX-TGE432 3 KX-TGE433 *4 KX-TG3634...

Before initial use, see “Getting Started” on page 10. · *2 KX-TGE432 *3 KX-TGE433 *4 KX-TG3634...

Documents

Transcript of Before initial use, see “Getting Started” on page 10. · *2 KX-TGE432 *3 KX-TGE433 *4 KX-TG3634...

Before initial use, see “Getting Started” on page 10. · 2 KX-TGE432 3 KX-TGE433 *4 KX-TG3634...

Transcript of Before initial use, see “Getting Started” on page 10. · 2 KX-TGE432 3 KX-TGE433 *4 KX-TG3634...