Base Side Remote Side - Doorking · 2372 Dual Repeater Board: Has LED displays for EACH side of the...
Transcript of Base Side Remote Side - Doorking · 2372 Dual Repeater Board: Has LED displays for EACH side of the...
WIRELESS DUAL BAND REPEATER KITDoorKing Part Number
2372-080The wireless dual band repeater kit (DBR) extends and expands the wireless communication range between an access control system and wireless tracker expansion board or “tracker board”. It gets installed between the wireless devices that are too far or obstructed from each other to reliably communicate with each other. It will receive a signal sent to it and repeat that signal to the next wireless device. Multiple DBRs can be used in the same communication line of a tracker board. The signal range of a DBR is approximately 500 ft direct-line-of-sight with no signal interference.
IMPORTANT:Install the repeaterso the antenna is in a location that is NOT surrounded by metal and is in free air as high as possible above the ground. Minimum 15 ft above ground recommended.
RF Range:Set as shown.
1/2” thick wall PVC conduit recommended
(not supplied).Metal conduit may
interfere with wireless signal.
Base side communicates with the wireless Baseboard of the 1830 series. The Channel and ID of the Base side MUST match the Channel and Net ID of the Baseboard.DO NOT set Base side the same as the Remote side.
LOW PWR switch ON-Up Position, board is put in a low power operating mode where both LED signal displays
will turn OFF when not needed.
Remote side communicates with the wireless Tracker board. The Channel and ID of the Remote side MUST match the Channel
and Net ID of the Tracker board. DO NOT set Remote side the
same as the Base side.
Up to 5 Dual Band Repeaters (DBR) can be used in a cascade format to extend signal distance. The Base Side of 2nd DBR MUST match the Channel and ID of the Remote Side from the 1st DBR and so on. Make sure the Channel and ID combinations are UNIQUE for every DBR in the cascade.
Installation
Base Side Remote Side
Cascading Dual Band Repeaters
Range testing is HIGHLY recommended before FINAL installation.
Important Antenna Note:Antenna range WILL VARYGREATLY depending on individualsetup: Antenna height above the ground, background signal interference, physical obstructions (trees, buildings etc.).Adverse weather (rain) CAN also affect antenna range.
0F E DCBA
987
654321
0F E DCBA
987
654321
0F E DCBA
987
654321
0F E DCBA
987
654321
POWER
BASEPROGRAM
REMOTEPROGRAM
PAIREDREMOTE
SW4
SW5SW1
D10D2
BASEPAIRED
REMOTEPAIRED
BASERF RANGE
REMOTERF RANGE
BASE REMOTE
CHID CHID
BASE SIGNAL REMOTE SIGNAL
2372-011
12VDC INPUT
LOW PWR
+-
RF STRENGTH
RF SYNC
RF LOST
2373-010
BASE REMOTE
Power Transformer18 GA. Wire 100 ft max16 GA. Wire 200 ft max
Wire Polarity Matters!Note: Rev “B” circuit board uses 5VDC.
2361 WirelessBaseboard
2358 WirelessTracker Board
77 88 99
44 55 66
11 22 33
00OPEROPER
WXYZWXYZTUVTUVPQRSPQRS
MNOMNOJKLJKLGHIGHI
DEFDEFABCABCSPSP
CALL
ZA
TELEPHONE ENTRY SYSTEM
HOLD TO SCAN
OPERATING INSTRUCTIONSUse “A to Z” Buttons to LocateName and Code Number on Display.Names are In Alphabetical Order.To Call, Enter Code Number onKeypad or Press “Call” Button. IfLine is Busy, Press “#” or “Call” toHang Up. Try Again.Enter on Open Display and Tone.
1.
2.
3.
77 88 99
44 55 66
11 22 33
00OPEROPER
WXYZWXYZTUVTUVPQRSPQRS
MNOMNOJKLJKLGHIGHI
DEFDEFABCABCSPSP
CALL
ZA
TELEPHONE ENTRY SYSTEM
HOLD TO SCAN
OPERATING INSTRUCTIONSUse “A to Z” Buttons to LocateName and Code Number on Display.Names are In Alphabetical Order.To Call, Enter Code Number onKeypad or Press “Call” Button. IfLine is Busy, Press “#” or “Call” toHang Up. Try Again.Enter on Open Display and Tone.
1.
2.
3.
Tracker
Black - NEG
Red + POS
Rev “C”or higherCircuitBoard
1st DBR
2nd DBR
3rd DBR
4th DBR
5th DBR
Baseboard
Channelsmatchand
IDs matchand both are
uniquein cascade
Channelsmatchand
IDs matchand both are
uniquein cascade
Channelsmatchand
IDs matchand both are
uniquein cascade
Channelsmatchand
IDs matchand both are
uniquein cascade
Channelsmatchand
IDs matchand both are
uniquein cascade
Channelsmatchand
IDs matchand both are
uniquein cascade
Note: DoorKing offers a Wireless Test Range Kit (P/N 1514-130) to allow easy testing of the wireless signal between 2 devices at chosen locations BEFORE installation of the devices. The self-powered test kit measures the wireless signal between 2 devices in ANY chosen locations. Ensuring that a good signal can be achieved before installation occurs.
Example:The wireless baseboardMUST be set to: ID: E CH: 4
Example:The wireless
tracker boardMUST be set to:
ID: 2 CH: 9
cascade
500 ft
FarNear
84
85 MAX setting
7276
6762
58
52
50
PINK
PURPLE
BLUE
GREEN
ORANGE
YELLOW
ON
PowerSupply12VDC
When boards are PAIRED: Only card codes/entry codes/remote codes from paired tracker boards will be accepted.
Base Side of 2372: To pair the 2372 Base side with a 2361 Baseboard, the 2372 base side MUST be in an UNPAIRED mode:Depress the BASE PROGRAM button (SW1) on the 2372 base side for few seconds until the RF LOST LED blinks rapidly and then turns steady RED.Then press the PAIR button on the 2361 baseboard for few seconds to PAIR with the 2372 BASE side ONLY. Once the 2372 Base side receives a pairing command from the 2361 baseboard, the middle green LED (RF SYNC) and the bottom red LED (RF LOST) blink rapidly; this indicates it has successfully been paired with the 2361 Baseboard. The BASE PAIRED LED turns green (D2) and will stay lit on 2372 Base side.
Pairing Boards Together
Automatic UNpaired Communication
LED Signal Indicators
DoorKing Technical Support: 1-800-826-7493
RFSECURE
RFSECURE
RF STRENGTH
RF SYNC
RF LOSTRF LOST2373-010
BASE REMOTE
RRT
RF STRENGTH
RF SYNC
RF LOSTRF LOST
RF SYNC
2373-010
BASE REMOTE
RRT
RRRRRR
Remote Side of 2372: To pair the 2372 Remote side with the wireless tracker board, unpaired communication must have already been established between the 2.
The RF SECURE LED will remain ON steady red on top of 2358 tracker board. Press the 2372 Remote side PAIRED REMOTE button (SW4) for 3 seconds or
until the 2372 REMOTE PAIRED Blue LED (D10) blinks rapidly. Once 2358 tracker board has been successfully paired to Remote side of 2372,
the RF SECURE LED will turn green and remain lit on 2358 tracker board.
Due to the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays or losses of data are rare when wireless devices are used in a normal manner with a well-constructed network, DoorKing wireless products should not be used in situations where failure to transmit or receive data could result in damage of any kind to the user or any other party, including but not limited to personal injury, death, or loss of property. DoorKing, Inc. accepts no responsibility for damages of any kind resulting from delays or errors in data transmitted or received using DoorKing wireless products, or for failure of DoorKing wireless products to transmit or receive such data.
Powering up boards will automatically establish communication between them and the baseboard. RF STAT/BASE & REMOTE PAIRED/RF SECURE LEDs will remain RED on the boards which indicates the boards are communicating with each other, but UNPAIRED. This means that card codes/entry codes/remote codes will be accepted from ANY tracker board that is set to the same channel and ID setting. See below to PAIR boards if desired.
LED displays on boards will indicate the signal loss between the boards. A smaller number is a stronger signal. 75 or lower is recommended.
RF STRENGTH LED should be GREEN on each board. YELLOW is marginal strength, RED is poor strength.
2361 Baseboard: LED Display shows the RF Range setting of the baseboard for 2 sec then shows signal loss that the board is actually receiving from 2372 Base side.
2372 Dual Repeater Board: Has LED displays for EACH side of the repeater which shows signal loss for Base and Remote sides.
2358 Tracker Board:
Do not operate DoorKing wireless products in areas where cellular modems are not advised without proper device certifications. These areas include environments where cellular radio can interfere such as explosive atmospheres, medical equipment, or any other equipment which maybe susceptible to any form of radio interference. DoorKing wireless products can transmit signals that could interfere with this equipment. Do not operate DoorKing wireless products in any aircraft, whether the aircraft is on the ground or in flight. In aircraft, DoorKing wireless products MUST BE POWERED OFF. When operating, DoorKing wireless products can transmit signals that could interfere with various onboard systems.
Note: Some airlines may permit the use of cellular phones while the aircraft is on the ground and the door is open. DoorKing wireless products may be used at this time.
The driver or operator of any vehicle should not operate DoorKing wireless products while in control of a moving vehicle. Doing so will detract from the driver or operator’s control and operation of that vehicle. In some states and provinces, operating such communications devices while in control of a vehicle is an offence.
Safety and Hazards
0F E DCBA
98
7654321
0F E D BA
98
7654321
0F E DCBA
98
7654321
0F E DCBA
98
7654321
POWER
BASEPROGRAM
REMOTEPROGRAM
PAIREDREMOTE
SW4
SW1
D10
REMOTEPAIRED
BASERF RANGE
REMOTE
BASE REMOTE
CHID CHID
BASE SIGNAL
2372-011
12VDC INPUT
LOW PWR
+-
RF LOST
2373-010
14131211654321
DOORKING2363-010
PAIREDON
OFF
0F E
DC
BA98765
43 2 1
0F E
DC
BA98765
43 2 1
RF RANGECH
NETID
RCVD
ALLOW
DENY
STATUS
SYNC LOST
SYNC REVD
HEARTBEAT
DISPLAYOFF/ON
RESET
PROG
RF STAT STRENGTH RLY 1 RLY 2
DOORKING2361-010
PAIR
3433323130292827262524232221
14151617181920
13121110987654321
ON1
0
7
65
4 3
NC
OUTPUTRELAY
NONC
ALARMRELAY
NONC
AUXRELAY
NO
ENT
RESET
2358-010CODEBAD
PROGRAM
0F E DCBA
321
0F E DCBA
98
7654321
RF ID
RF
1489-010
RF RANGE
TTTTTT HHHS HHSSS NGTHNGTHENGTHENENEENEEEEREREERRERRRRRTRRTRTRTRTTRTSTSTSTS
2361 Wireless Baseboard2372 Wireless Dual Repeater Board
2358 Wireless Tracker Board
PAIRED REMOTE (SW4)
PAIR
BASEPROGRAM
(SW1)
RF SECURE
RF SYNCLED Display
Program Buttons
LED Base Display LED Remote Display
LED Display
RF STAT
RF STRENGTH
RF STRENGTH
RF STRENGTH
BASE PAIRED (D2)
Important Notice
To Display RF Signal Loss• Use UP and Down Arrow Buttons to select programming Step 21 shown on LED display.
• Press ENT Button to show Signal Loss number on LED display.ENT
75 or lower is recommended.
ONLY red when it sees unpaired
tracker board.
ON
Examples using Dual Band Repeaters - DBR
WirelessTrackerBoard
DBRDBR
DBR
77 88 99
44 55 66
11 22 33
00OPEROPER
WXYZWXYZTUVTUVPQRSPQRS
MNOMNOJKLJKLGHIGHI
DEFDEFABCABCSPSP
CALL
ZA
TELEPHONE ENTRY SYSTEM
HOLD TO SCAN
OPERATING INSTRUCTIONSUse “A to Z” Buttons to LocateName and Code Number on Display.Names are In Alphabetical Order.To Call, Enter Code Number onKeypad or Press “Call” Button. IfLine is Busy, Press “#” or “Call” toHang Up. Try Again.Enter on Open Display and Tone.
1.
2.
3.
WirelessBaseboard
1830 series
WirelessBaseboard
1830 series
DomeAntenna
Up to 24 Tracker Boards Communicate Wirelessly, NO HARDwiring Trackers to 1830
Up to 12 Tracker Boards Communicate Wirelessly and HARDwiring Trackers to 1830
TIP: DO NOT USEchannel “0” or “F” if possible.They are the weakest.
Channels “4”, “9” and “E” are good. They are outside the bandwidth of the most used WiFi channels.
DBR Note: Extra DBRs can be used to extend signal distance between devices.
Dome Antenna Note: When the dome antenna has to be used on the 1830, a DBR will extend the wireless distance from it.
DBR
Channels match, IDs match and different from other DBRs.
Channels match, IDs match and different from baseboard and other DBRs.
Channels match, IDs match and different from baseboard and other DBRs.
WirelessTrackerBoard
PINK
PURPLE
TrackerBoard
DBRDBR
DBR
TIP: DO NOT USEchannel “0” or “F” if possible.They are the weakest.
Channels “4”, “9” and “E” are good. They are outside the bandwidth of the most used WiFi channels.
DBR Note: Extra DBRs can be used to extend signal distance between devices.
DBR
Channels match, IDs match and different from other DBRs.
Channels match, IDs match and different from baseboard and other DBRs.
Channels match, IDs match and different from baseboard and other DBRs.
Channels match, IDs match and different from baseboard and other DBRs.
Channels match, IDs match and different from baseboard and other DBRs.
Channels match, IDs match and different from baseboard and other DBRs.
Channels match, IDs match and different from baseboard and other DBRs.
There are 16 individual board addresses available for the tracker boards (16 tracker boards). Board addresses 3-10 for Relay 2/Wiegand 2 input and 11-18 for Relay 1/Wiegand 1 input. An additional 8 tracker boards can be used with zone addressing. There are many combinations of wireless configurations and DBRs will extend the signal distance between devices to allow up to 24 trackers to be used. Wireless tracker boards can also connect directly to the 1830 when in range. This diagram assumes that NO tracker boards will be HARDwired to the 1830. See below for wireless and hardwired tracker boards.
Relay 1/Wiegand 1 input terminal is available on the 1830 baseboard to HARDwire tracker boards if desired. When any trackers are HARDwired to the baseboard, only the Relay 2/Wiegand 2 input is available for wireless communication. 8 board addresses 3-10 (8 tracker boards) and an additional 4 tracker boards can be used with zone addressing. There are many combinations of wireless configurations and DBRs will extend the signal distance between devices to allow up to 12 trackers to be used for the Relay 2/Wiegand 2 input. Wireless tracker boards can also connect directly to the 1830 Relay 2/Wiegand 2 input when in range.
Relay 1/Wiegand 1 HARDwired input
Relay 2/Wiegand 2 Wireless input
77 88 99
44 55 66
11 22 33
00OPEROPER
WXYZWXYZTUVTUVPQRSPQRS
MNOMNOJKLJKLGHIGHI
DEFDEFABCABCSPSP
CALL
ZA
TELEPHONE ENTRY SYSTEM
HOLD TO SCAN
OPERATING INSTRUCTIONSUse “A to Z” Buttons to LocateName and Code Number on Display.Names are In Alphabetical Order.To Call, Enter Code Number onKeypad or Press “Call” Button. IfLine is Busy, Press “#” or “Call” toHang Up. Try Again.Enter on Open Display and Tone.
1.
2.
3.
120 S. Glasgow AvenueInglewood, California 90301 U.S.A.2372-065-E-1-16 Copyright 2015 DoorKing, Inc. All rights reserved.
Board Addresses 3-10
Board Addresses 11-18
PURPLE
PINK
GREEN
GREEN
YELLOW
YELLOW
ORANGE
ORANGE