BARSPLICER DATA SHEET– Dimensions and Data [inch-pound · PDF fileUnless otherwise...
Transcript of BARSPLICER DATA SHEET– Dimensions and Data [inch-pound · PDF fileUnless otherwise...
Unless otherwise specified, bars shall be ASTM A615 / A615M Grade 60; epoxy coated bars shall be ASTM A775 / A775M Grade 60; bend diameters and standard hook dimensions shall be per ACI Detailing Manual SP-66; length tolerances shall be per the CRSI Manual of Standard Practice. Customer is responsible for notifying BPI of any special space restrictions, tolerance, bar grade, coating thickness and/or strength requirements before placing order. All fabricated and/or in-process setting bars, splice bars and parts are non-cancellable and non-returnable. While the information contained in this document is believed to be accurate at the time of publication, BPI reserves the right to make changes, design modifications, corrections and other revisions as it sees fit, without notice. All products described herein are supplied in accordance with BPI’s standard Terms and Conditions of Sale. This document is of a promotional nature only. Aspects of structural design, evaluation of product fitness for use, suitability or similar attributes are the responsibility of others.
BPI ® BARSPLICER DATA SHEET– Dimensions and Data [inch-pound units]
HOW TO ORDER BPI® BARSPLICER SETTING AND SPLICE BARSThe most commonly used splice and setting bars are STRAIGHT or have a 90 DEGREE HOOK as follows…
SETTING BAR SPLICE BARDB
CA
The following chart is an easy way to organize your BPI Barsplicer requirements. Many other configurations can be ordered as shown on the BPI Barsplicer configuration chart… just include the BPI PART NUMBER for easy reference.
4567891011
1/2 − 13 UNC5/8 − 11 UNC3/4 − 10 UNC7/8 − 9 UNC1 − 8 UNC
1 1/8 − 7 UNC1 1/4 − 7 UNC1 3/8 − 6 UNC
0.280.350.400.500.90 1.502.352.40
1 3/4
22 1/8
2 1/2
33 1/2
44 1/2
7/8
11 1/8
1 1/4
1 1/2
1 3/4
22
2 x 22 x 22 x 22 x 22 x 2 3 x 33 x 33 x 3
−−−−− −−−
1/2 − 13 UNC5/8 − 11 UNC3/4 − 10 UNC7/8 − 9 UNC1 − 8 UNC
1 1/8 − 7 UNC1 1/4 − 7 UNC1 3/8 − 6 UNC
0.220.300.350.500.90 1.502.352.40
1 3/4
22 1/8
2 1/2
33 1/2
44 1/2
7/8
11 1/8
1 1/4
1 1/2
1 3/4
22
−−−−− −−−
−−−−− −−−
4567891011
4567891011
1/2 − 13 UNC5/8 − 11 UNC3/4 − 10 UNC7/8 − 9 UNC1 − 8 UNC
1 1/8 − 7 UNC1 1/4 − 7 UNC1 3/8 − 6 UNC
0.150.200.400.500.85 1.051.501.55
1 3/8
1 1/2
1 3/4
22 1/4
2 5/8
33 3/8
7/8
11 1/4
1 3/8
1 5/8
1 3/4
22
3/16
1/4
1/4
5/16
3/8 7/16
1/2
9/16
−−−−− −−−
4567891011
1/2 − 13 UNC5/8 − 11 UNC3/4 − 10 UNC7/8 − 9 UNC1 − 8 UNC
1 1/8 − 7 UNC1 1/4 − 7 UNC1 3/8 − 6 UNC
0.220.370.550.951.42 2.152.503.75
3/4
7/8
15/16
1 1/4
1 5/16
1 1/2
1 5/8
1 7/8
1 1/4
1 1/2
1 3/4
22 3/8
2 3/4
2 7/8
3 1/4
−−−−− −−−
−−−−− −−−
REBARSIZE
THREADSIZE
WEIGHT(lbs)
LENGTH(in)
DIAMETER(in)
FLANGE(in)
BEVEL(in)BPI® BARSPLICER COUPLER WITH OPTIONAL FLANGE
BPI® BARSPLICER COUPLER / POSITION COUPLER
BPI® BARSPLICER STRUCTURAL CONNECTOR
BPI® BARSPLICER DoughNUTTM
QUANTITY BARSIZE
BLACKOR
EPOXY
SETTING BARS SPLICE BARSSPECIFY LENGTHS (FEET - INCHES)SPECIFY LENGTHS (FEET - INCHES)
FLANGEY/N
BPI PARTNUMBERSee Chart
BPI PARTNUMBERSee Chart‘A’ ‘B’ OTHER ‘C’ ‘D’ OTHER
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
−
MEMBER
CRSI®BarSplice Products, Inc., 4900 Webster Street, Dayton OH 45414, USATel: (937) 275-8700 Fax: (937) 275-9566 E-mail: [email protected]
Copyright © 2012, Barsplice Products, Inc., "BPI". All rights reserved.
Unless otherwise specified, bars shall be ASTM A615 / A615M Grade 60; epoxy coated bars shall be ASTM A775 / A775M Grade 60; bend diameters and standard hook dimensions shall be per ACI Detailing Manual SP-66; length tolerances shall be per the CRSI Manual of Standard Practice. Customer is responsible for notifying BPI of any special space restrictions, tolerance, bar grade, coating thickness and/or strength requirements before placing order. All fabricated and/or in-process setting bars, splice bars and parts are non-cancellable and non-returnable. While the information contained in this document is believed to be accurate at the time of publication, BPI reserves the right to make changes, design modifications, corrections and other revisions as it sees fit, without notice. All products described herein are supplied in accordance with BPI’s standard Terms and Conditions of Sale. This document is of a promotional nature only. Aspects of structural design, evaluation of product fitness for use, suitability
or similar attributes are the responsibility of others.
STRAIGHTSpecify
‘C’
90° BENDSpecify‘C’ & ‘D’
180° HOOKSpecify
‘C’
45° BENDSpecify‘C’ & ‘D’
135° BENDSpecify‘C’ & ‘D’
DOUBLE ENDSpecify‘C’ & ‘Z’
CONTINUITYDOUBLE END
Specify‘C’
POSITIONALSTRAIGHT
Specify‘Cp’
POSITIONAL90° BEND
Specify‘Cp’ & ‘D’
HEADEDSTRAIGHT
Specify‘C’
SPLICE BAR OPTIONS AND PART NUMBERS
BS-H
BS-G
BS-I
BS-P
BS-R
BS-O
BS-N
BS-L
BS-M
BS-T
C
C
D
C
D
C D
C
D
Cp
Cp
D
C
C
C
SETTING BAR OPTIONS AND PART NUMBERS
BS-B
BS-F
BS-E
BS-C
BS-Q
BS-A
BS-D
BS-J
BS-K
BS-S
STRAIGHTSpecify
‘A’
90° BENDSpecify‘A’ & ‘B’
180° HOOKSpecify
‘A’
45° BENDSpecify‘A’ & ‘B’
135° BENDSpecify‘A’ & ‘B’
DOUBLE ENDSpecify
‘A’
U-SHAPEDOUBLE END
Specify‘A’ & ‘B’
POSITIONALSTRAIGHT
Specify‘Ap’
POSITIONAL90° BEND
Specify‘Ap’ & ‘B’
HEADEDSTRAIGHT
Specify‘A’
A
A
B
A
B
AB
A
BA
A
B
Ap
Ap
B
A
RE
V.G
3/
01/2
017
BPI® BARSPLICER CONFIGURATION CHARTThe following chart shows the dimensions to specify when ordering setting and splice bars. Other configurations can be manufactured to order… just fax or e-mail a sketch to Barsplice Products, Inc. with your requirements.
Z