B5 4WD-Truck & Forklift 2013-6lr

Hardy Spicer Driveshaft Components Catalogue

Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13

This catalogue is the copyright of Hardy Spicer

www.hardyspicer.com.au

B:5-I

4 WHEEL DRIVE, TRUCK & FORKLIFTSECTION B:5

INDEX

MANUFACTURER SECTION

Forklift Shafts ..............................................................................B:5-1Japanese PTO ............................................................................B:5-5Daihatsu .....................................................................................B:5-7Honda .........................................................................................B:5-11Isuzu ...........................................................................................B:5-13Mercedes Benz ...........................................................................B:5-21Mitsubishi ....................................................................................B:5-29Nissan & Nissan UD ...................................................................B:5-37Scania .........................................................................................B:5-45Suzuki .........................................................................................B:5-51Toyota .........................................................................................B:5-55Volvo ...........................................................................................B:5-69


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-II


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



Forklift Shafts

B:5-1

Manitou Model Image Hardy Spicer O.E.Part No. Length Spline Bolt Holes Part No. Details

TCM 3.5T / 4T HS-1022 3EC-01-327111/10 221mm 13T 11mm 22mm 110mm PCD 77.35x77.35

TCM (OLD) HS-1009-13T 224W7-22011 196mm 13T 8mm 22mm 52 Spigot Male 45 x 53

KOMATSU HS-1009-18T 224W7-22012 196mm 18T 8mm 4T (2-7) (NEW) 30mm 42 Spigot Male 35 x 60

725 HS-1035 144mm 16T BOBCAT 56x56

Komatsu / TCM Model Image Hardy Spicer O.E.Part No. Length Spline Bolt Holes Part No. Details

Bobcat Model Image Hardy Spicer O.E.Part No. Length Spline Bolt Holes Part No. Details

TCM 4T HS-1009-13T-E 20103-85081 180mm 13T 8mm 4T (2-8) 22mm 42 Spigot Female 35 x 60

VARIOUS Aftermarket length suits 9-501-310333278 397151K 278.5mm 1310 both OE versions Flange 397152K 300mm Face


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-2

Model Image Hardy Spicer O.E.Part No. Length Spline Bolt Holes Part No. No.

S4S 4T HS-1008 91571-00050 211mm 13T 8mm FD25T 91571-00070 22mm 80mm PCD 91571-30050 57 x 57

Grader HS-1014 177mm 13T 8mm 22mm 34 Spigot 25 x 50

4 Ton HS-1006-L 91871-30040 300mm 13T 8mm 22mm 80mm PCD 57 x 57

Mitsubishi

4 Ton HS-1006 91871-10021 200mm 13T 8mm 22mm 80mm PCD 57 x 57

3.5 Ton HS-1001-1 91871-10011 160mm 13T 8mm 22mm 80mm PCD 57 x 57

2 Ton HS-1001 91171-10011 160mm 10T 8mm 18mm 80mm PCD 57 x 57

1.5 Ton HS-1018 185mm 10T 8mm 18mm 80mm PCD 57 x 57

1.5 Ton G10T HS-1001-L 275mm 10T 8mm 18mm 80mm PCD 57 x 57

Shaft is made out of phase

4 Ton HS-1029 91871-10050 175mm 13T 8mm 22mm 80mmPCD 57 x 57


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-3

Nissan Model Image Hardy Spicer O.E.Part No. Length Spline Bolt Holes Part No. No. FD40 HS-1011 37200-S1H00 255mm 14T 1140 24mm Spicer face

S-65 / FD35 7 Ton HS-1008-F 91871-10011 183mm 8mm 80mm PCD (57x57)

7 Ton HS-1016 92001-10090 360mm 8mm 80mm PCD 57 x 57

S4S HS-1008-0 91571-20010 205mm 13T 8mm Caterpillar 22mm 80mm PCD DP25 57 x 57 PP25 DP35 210mm CL 230mm WP

Model Image Hardy Spicer O.E.Part No. Length Spline Bolt Holes Part No. Details

Mitsubishi cont.

S4S HS-S4S-N 91324-00060 106mm RUJ-4012 MAIN SHAFT 91324-00062 F-F U/Joint 68mm C-C

S4S HS-S4S 91324-00030 106mm K5-A811 MAIN SHAFT F-F U/Joint 70.5mm C-C

3.5T / 4.5T HS-1011-2 12381-L6001 300mm 13T 1140 22mm Spicer face


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-4

Yale Model Image Hardy Spicer O.E.Part No. Length Spline Bolt Holes Part No. No. 2.5 Ton HS-1004 9147-844-01 70mm 8mm 65mm PCD 52 x 38 45 Spigot

4 Ton HS-1010 91324-08200 80mm 8mm 73mm PCD 57 x 46 45 Spigot

Toyota

7F HS-7F 67310-31720 350mm 8mm 34 Spigot 41 x 57

5F HS-1007 67310-32880-71 170mm 8mm 70mm PCD 57.5 x 40 34 Spigot

6F HS-6F 67310-31700-71 185mm 8mm 34 Spigot 41 x 57

3FD HS-1012 67310-32080-71 136mm 13T 8mm 22mm 34 Spigot 41 x 57

Model Image Hardy Spicer O.E.Part No. Length Spline Bolt Holes Part No. Details

7FD40 HS-7FD40 70mm MAIN DRIVE C-C H BAR

7FD40 HS-7FD40-2 165mm 8mm PUMP DRIVE 34 Spigot 41 x 57

5C BLOCK TYPE EACH END34 x 84 IC H BAR


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-5

JAPANESE PTO

K5-A549 20.00 57.50 1 CENTRE 0.787 2.264

K5-A553 22.00 62.00 1 CENTRE 0.885 2.441

K5-A558 25.00 77.00 1 SIDE 0.984 3.031

PART NO. C B1 B2 FIG. LUBE DESCRIPTION

FIGURE 1 FIGURE 2

C B1 CB1 B2

JAPANESE PTO UNIVERSAL JOINT KIT

FLANGE YOKE FIG. U.J. DIMENSIONS C/L OF U.J. SPIGOT DIA P.C.D. BOLT No. HOLE U.J. PART No. TO FACE M=MALE HOLE HOLES DIA. PART No. F=FEMALE PATTERN C B1 B2 L S M

2-2-A2309 ^ 1 26.99 81.76 50.0 M-42.00 69.46 60 x 35 4 8.08 K5-13XR 1.063 3.219 1.968 M-1.653 2.734 0.318

JAPANESE PTO FLANGE YOKE

M S B1

L

C

FIGURE 1

^ Suit 1310 Spicer series universal joint.


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-6

JAPANESE PTO

PART No. SPLINEO.D. & No.

LENGTHFACE TOPOINT OF

WELD COMPL

SPIGOT U/JOINT BUTT DIA.

D

NOTES

MDP-552 25.00-18 270.00 34.00 K5-A549 34.00 BOLT C-C 50 x 25

0.984 10.630 1.339 1.339

PART No. LENGTHFACE TOPOINT OF

WELDL


D

NOTES

MDP-652 92.00 34.00 K5-A549 34.00 BOLT C-C 50 x 25

3.622 1.339 1.339

L

D

L

D

PART No. SPLINEO.D. & No.


WELD COMPL1


WELDL2


D

NOTES

MDP-60X35 KIT 32.00-14 240.00 102.00 42.00 K5-A558 37.00 BOLT C-C 60 x 35

1.260 9.449 4.016 1.654 1.457

JAPANESE PTO SLIP JOINT ASSEMBLY

JAPANESE PTO FIXED JOINT ASSEMBLY

JAPANESE PTO PSA KIT ASSEMBLY

L1 L2

Note: MDP-60X35 KIT does not include tube.


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-7

RUJ-1503 22.50 37.50 2 SIDE 0.885 1.476

RUJ-1502 22.50 37.50 2 NIL 0.885 1.476

K5-A522 28.00 80.00 1 CENTRE Rocky 1.102 3.150

RUJ-2114 28.00 80.00 1 SIDE Rocky to 1310 Series 1.102 3.150 Conversion u/oint 26.99 81.76 1.063 3.219

RUJ-2505 28.60 65.10 1 SIDE 1.126 2.563

DAIHATSU

Part No. C B1 B2 FIG. LUBE DESCRIPTION

FIGURE 1 FIGURE 2

C B1 CB1 B2

DAIHATSU UNIVERSAL JOINT KIT


M S B1

L

C

FIGURE 1

DA-2-021 1 28.0 80.0 50.0 M-50.00 88.0 58 x 67 4 10.0 K5-A522 37315-87601 1.102 3.150 1.968 M-1.968 3.465 0.394

DA-2-022 1 28.0 80.0 55.0 M-50.00 92.5 65 x 65 4 11.1 K5-A522 37315-87602 1.102 3.150 2.165 M-1.968 3.642 0.437

DAIHATSU FLANGE YOKE

FIGURE 2

C

SM

L

B2

Available while stocks last


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-8

DAIHATSU

SLIP YOKE FIG. DIMENSIONS SPLINE C/LINE TO STUB U.J. COMMENTS PART No. O.D. & No. END OF PART No. PART No. SPLINE C B1 B2 B L

B1

C

L

FIGURE 1

DA-3-016KX 1 28.00 80.00 30.00-16 195.0 DA-42-026 K5-A522 37302-87607 1.102 3.150 1.181 7.677

DA-3-017KX 1 28.00 80.00 30.00-16 240.0 DA-42-025 K5-A522 37302-87606 1.102 3.150 1.181 9.449

DAIHATSU SLIP YOKE

STUB PART No. SPLINE DIA. & No. SPLINE TYPE LENGTH OF END OF SPLINE TUBE O.D. & SPLINE TO POINT OF THICKNESS WELD B G L T

G

B

L

T

DA-42-026 30.00-16 STEEL 140.0 175.0 65X1-6mm 1.181 3.720 6.890 65.00 x.1.6mm

DA-42-025 30.00-16 STEEL 125.0 220.0 65X1-6mm 1.181 2.550 8.661 65.00 x.1.6mm

DAIHATSU STUB

Dust cap to suit both slip yokes - DA-86-028 - Order seperately




Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-9

DAIHATSU

B1 T

C

FIGURE 1

B2 T

C

FIGURE 2

WELD YOKE FIG. U.J. DIMENSIONS C/LINE TO TUBE O.D. BUTT TYPE U.J. PART No. POINT OF & WALL PART No. WELD THICKNESS C B1 B2 L T

DA-26-027 1 28.00 80.00 65.0 65X1-6MM H K5-A522 1.102 3.150 2.559 65.00 x.1.6mm

DAIHATSU WELD YOKE

L L

V12. V22. V32. Delta DA-30-3810 37208-87302 77- 35mm 119mm

Vehicle Model Hardy Spicer O.E.Part No. Year Bearing Bolt Hole Part No. ID Centres

DAIHATSU CENTRE BEARINGS



Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-10

DAIHATSU


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-11

HONDA

HONDA UNIVERSAL JOINT KIT

FIGURE 1 FIGURE 2

C B1 CB1 B2

K5-A554 22.00 65.00 1 NIL 0.866 2.559

K5-A557 25.00 64.00 1 NIL 0.984 2.520


HONDA HONDA CRV TWINSHAFTSPart No. Year O/All

LengthF-FL

Front Shaft LengthF-C/Brg

A

Flange Bolt Hole Pattern

Flange PCD

Centre Brg OEM Part No.

HO-PSA-CRV-RDS7 1997~2001 2100 998 53.55 x 44.85 69.85 HO-30-6010 40100S10003

82.677 39.291 8.00 X 4 2.750 40100S10A01

HO-PSA-CRV-REZ4 2002~2006 2053 822 53.55 x 44.85 69.85 HO-30-6010 40100S9AE01

80.827 32.362 8.00 X 4 2.750 40100SCAA0

40100SCWA0

HO-PSA-CRV-RE17 2007~2011 2060 1165 53.55 x 44.85 69.85 HO-30-6010 40100SWAA0

81.102 45.866 8.00 X 4 2.750

L

A

Honda Vehicle Model Hardy Spicer O.E.Part No. Year Bearing Bolt Hole Part No. ID Centres

CRV HO-30-6010 405210-S10-003 1997- 25mm 174mm


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-12

HONDA


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-13

RUJ-2033 29.00 53.10 3 SIDE Holden / Isuzu 1.14 2.09

RUJ-2036 29.00 53.10 3 NON-LUBE Holden / Isuzu 1.14 2.09

RUJ-2110 29.00 53.10 1 & 3 SIDE Isuzu to 1310 series 1.14 2.09 27.00 81.76 1.06 3.22

RUJ-3011 29.02 72.00 3 SIDE Holden / Isuzu 1.14 2.83

K5-A679 33.00 93.00 1 SIDE 1.30 3.66

K5-A567 35.00 104.00 1 CENTRE 1.38 4.09

K5-A523 36.00 97.00 2 CENTRE 1.42 3.82

K5-A639 40.00 115.00 1 SIDE 1.57 4.53

K5-A753 42.00 115.00 1 CENTRE 1.65 4.53

K5-A574 42.00 125.00 2 CENTRE 1.65 4.92

K5-A577 46.00 136.00 2 CENTRE 1.81 5.35

K5-A582 48.00 145.00 2 CENTRE 1.89 5.71

K5-A779 49.20 154.70 1 CENTRE 687-50 series 1.94 6.09

K5-A754 50.00 155.00 2 CENTRE 1.97 6.10

K5-A694 55.00 169.00 2 CENTRE 2.17 6.65

ISUZU

Part No. C B1 B2 / E FIG. LUBE DESCRIPTION

FIGURE 1

C B1

ISUZU UNIVERSAL JOINT KITFIGURE 2

Cap Type(Lock Plate)

FIGURE 3


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-14

ISUZU


M S B1

L

C

FIGURE 1

IS-2-2033 2 29.00 53.10 48.00 M-65.00 85.00 50 x 69 4 10.30 RUJ-2033 1.14 2.09 1.890 M-2.559 3.346 0.406 RUJ-2036

3-2-3900 2 30.16 106.30 55.00 M-80.00 100.00 59 x 81 4 10.20 K5-GB10R 1.30 4.19 2.165 M-3.150 3.937 0.402 1410

IS-2-012 1 33.00 93.00 55.00 M-80.00 100.00 59 x 81 4 12.10 K5-A679 1.38 3.66 2.165 M-3.150 3.937 0.476

3-2-013 1 34.93 106.30 62.00 M-80.00 110.00 55 x 95.2 4 12.10 5-188X 1.38 4.19 2.441 M-3.150 4.331 0.476 1480

3-2-014 1 34.93 106.30 65.00 M-80.00 100.00 59 x 81 4 12.10 5-188X 1.38 4.19 2.559 M-3.150 3.937 0.476 1480

IS-2-013 1 35.00 104.00 63.00 M-80.00 110.00 55 x 95.2 4 12.10 K5-A567 1.38 4.09 2.480 M-3.150 4.331 0.476

IS-2-014 1 35.00 104.00 63.00 M-90.00 110.00 55 x 95.2 4 12.10 K5-A567 1.38 4.09 2.480 M-3.543 4.331 0.476

IS-2-639 1 40.00 115.00 70.00 M-90.00 119.80 71 x 97 4 14.10 K5-A639 1.57 4.53 2.756 M-3.543 4.716 0.555

IS-2-019 3 42.00 125.00 72.00 M-90.00 75 x 118 4 14.10 K5-A574 1.65 4.92 2.835 M-3.543 0.555

5-2-244# 3 47.63 134.94 M-90.00 75 x 118 4 14.10 5-279X 1.88 5.31 M-3.543 0.555 1610

IS-2-582 3 48.00 145.00 M-100.00 92 x 131 4 16.00 K5-A582 1.89 5.71 M-3.937 0.630

6-2-197416# 3 49.21 154.78 80.00 M-100.00 92 X 131 4 16.0 5-280X 1.94 6.09 3.150 3.937 0.630 1710 2-687-502300500 4 49.20 154.70 85.00 180.00 150.00 4 15.0 K5-A779 1.94 6.09 3.346 FLANGE O.D. 5.906 0.591 687-50

ISUZU FLANGE YOKE

FIGURE 2

FIGURE 3

C

SM

L

B2

FIGURE 4

# INDENT ONLY


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-15

ISUZU SLIP YOKE

ISUZU

FIGURE 2FIGURE 1

SLIP INVOLUTE CENTRE TOTAL MAX. TUBE O.D. U.J. SERIES ASSEMBLY SPLINE TO WELD SLIP ANGLE & WALL PART No. O.D. POINT THICKNESS A L C

ISUZU SLIP ASSEMBLY

6-687-507780204 74 x 2.00 DIN 5480 180.0 120X5MM K5-A779 687-50 7.087 120.0 X 5.0 SERIES

B1

C

L C

L

B B2

SLIP YOKEPART No.

FIG. DIMENSIONS SPLINEO.D. & No.

C/LINE TO END

OF SPLNE

LENGTH THROUGH

HOLE

STUBPART No.

U/JOINT PART No.

C B1 B2 B L GIS-3-2033 2 29.00 53.10 31.00-17 168.00 130.00 IS-42-2033 RUJ-2033 HOLDEN ISUZU

1.14 2.09 1.22 6.61 5.12

IS-3-012KX 1 33.00 93.00 40.00-14 190.00 IS-42-012 K5-A679

1.30 3.66 1.57 7.48

IS-3-004KX 1 35.0 104.00 45.00-16 190.00 158.00 IS-42-032 K5-A567 DUST CAP - DCKIS11.38 4.09 1.77 7.48 6.22

IS-3-639 1 40.00 115.00 49.70-18 255.00 198.00 IS-42-639 K5-A639

1.57 4.53 1.96 10.04 7.80

IS-3-574 2 42.00 125.00 49.70-18 254.00 IS-42-034 K5-A574 NO DUST CAP SUPPLIED

1.65 4.92 1.96 10.00 USE 6-687-200900000 COVER

IS-3-582 2 48.00 145.00 49.70-18 315.00 IS-42-582 K5-A582 NO DUST CAP SUPPLIED

1.89 5.71 1.96 12.02 USE 6-687-200900000 COVER

IS-3-008KX FLANGED TYPE 49.70-18 185.00 IS-42-034 K5-A574 SUITS FLANGE IS-2-0191.96 7.28


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-16

STUB PART No. SPLINE DIA. & No. TUBE & LENGTH OF END OF SPLINE SUITS SLIP BUTT SPLINE TO POINT OF YOKE PART No. DIAMETER WELD B I G L

IS-42-2033 31.00 x 17 140.00 175.00 IS-3-2033 1.22 58.15 5.51 6.89

IS-42-012 40.00 x 14 206.00 IS-3-012KX 1.57 77.68 9.25

IS-42-032 45.00 x 16 180.00 235.00 IS-3-004KX 1.77 83.15 7.09 9.25

IS-42-582 49.70 x 18 88X4MM 196.00 315.00 IS-3-582 1.96 80.30 7.72 12.40

IS-42-639 49.70 x 18 90X4MM 210.00 262.00 IS-3-639 1.96 82.35 8.27 10.31

IS-42-034 49.70 x 18 90X4MM 255.00 IS-3-574 1.96 82.35 10.04 IS-3-008KX

ISUZU STUB

ISUZU

B

L

T

G

ISUZU MIDSHIP STUB STUB SPLINE END LENGTH TUBE BEARING BEARING MATCHING PART No. O.D. & No. TO WELD OF SPLINE DIAMETER DIAMETER PART No. COMP. POINT FLANGE L G B

IS-53-012 39.50 x 14 INV 119.00 56.00 40.00 IS-30-5610 IS-1-012 1.555 x 14 4.685 2.205 1.575 IS-53-567-40 39.80 x 18 INV 105.00 45.00 2810-0000 40.00 IS-30-5610 IS-1-567-40 1.567 x 18 4.134 1.772 88.90 x 3.41 1.575 IS-53-567 44.45 x 16 INV 0.00 54.00 2810-0000 45.00 IS-30-5110 IS-1-567 1.750 x 16 0.000 2.126 88.90 x 3.41 1.771 IS-53-031* 44.45 x 16 INV 168.00 54.00 45.00 IS-30-5110 IS-1-043 1.750 x 16 6.614 2.126 1.771

NUT : IS-74-001 WASHER : IS-73-001 TO SUIT MIDSHIP STUBS ABOVE* DISCONTINUED - AVAILABLE WHILE STOCKS LAST


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-17

ISUZU

BUTT TYPE H=HOLLOW, S=SOLID

WELD YOKE FIG. U.J. DIMENSIONS C/LINE TO TUBE BUTT TYPE U.J. PART No. POINT OF O.D. & WALL PART No. WELD THICKNESS C B1 B2 L T IS-26-2033 2 29.00 53.10 44.50 S RUJ-2033 1.14 2.09 1.752 65.00 x 3.50

IS-28-012 1 33.00 93.00 63.00 K5-A679 1.30 3.66 2.480 82.55 x 2.41

IS-28-567 1 35.00 104.00 63.70 2810-0000 H K5-A567 1.378 4.094 2.508 88.90 x 3.41

IS-26-639 1 40.00 115.00 72.00 90X4MM H K5-A639 1.18 3.08 2.835 90.00 x 4.00

IS-28-044 42.00 125.00 79.00 K5-A574 1.65 4.92 3.110

IS-28-582 48.00 145.00 99.00 88X4MM K5-A582 1.89 5.71 3.898 88.00 x 4.00

2-687-504000000 49.2 154.7 120X5MM H K5-A779 1.94 6.09 120.00 x 5.00 687-50

ISUZU WELD YOKE

B2 T

C

FIGURE 2

L

B1 T

C

FIGURE 1

L

ISUZU COMPANION FLANGES COMPANION FIG. LENGTH SPLINE MATCHING SPIGOT P.C.D. BOLT No. HOLE SERIES FLANGE DIA. & No. STUB DIA. HOLE HOLES DIA. PART No. L1 D6 PATTERN 3-1-014 1 69.00 1.500 x 10 Spl K4-57-GB2651 F-80.00 100.00 59 x 81 4 10.2 1410 2.717 38.10 3.150 3.937 0.402 IS-1-012 1 1.555 x 14 Spl IS-53-012 F-80.00 59 x 81 4 10.2 39.50 3.150 0.402 IS-1-567-40 1 69.00 1.567 x 18 Spl IS-53-567-40 F-80.00 110.00 55 x 95.2 4 12.1 2.717 39.80 3.150 4.331 0.476 3-1-013 1 69.00 1.750 x 10 Spl 4-53-341 F-80.00 110.00 55 x 95.2 4 12.1 1480 2.717 44.45 3.150 4.331 0.476 IS-1-567 1 69.00 1.750 x 16 Spl IS-53-567 F-80.00 110.00 55 x 95.2 4 12.1 2.717 44.45 3.543 4.331 0.476 IS-1-043* 1 1.750 x 16 Spl IS-53-031 F-90.00 110.00 55 x 95.2 4 12.1 44.45 3.543 4.331 0.476

FIGURE 1 FIGURE 2

* DISCONTINUED - AVAILABLE WHILE STOCKS LAST


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-18

ISUZUL

B

L1

T D1D

ASSEMBLY SPIGOT BEARING SPLINE FLANGE FLANGE TUBE O.D. BOLT HOLE PART DIA. PART NO. DETAILS TO WELD TO BRG & WALL CENTRES DIA. NO. & DIA. & DIA. POINT CENTRE THICKNESS B L L1 T D x D1

ISUZU MIDSHIP ASSEMBLY

IS-56-567* M-80.00 140.00 78.50 2813-0000 55.0 x 95.2 12.2 FIGURE 1 3.150 45.00 5.512 3.091 88.90 x 2.41 PCD = 119.80 IS-56-639* M-90.00 IS-30-5110 44.45 X 16 110.00 80.00 90X4-1/2MM 70.5 x 97.0 14.3 FIGURE 1 3.543 45.00 4.331 3.150 90.00 x 4.50 PCD = 119.80 7-613-5509006500 6-613-550100690 120X5MM 15.0 FIGURE 2 55.00 120.00 x 5.00 PCD = 150.00*Available only as complete assembly - while stocks last. Use IS-1-567, IS-53-567 & Bearing to suit.

FIGURE 1 FIGURE 2


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-19

ISUZU Isuzu


N SERIES IS-30-7050 8-971311143-1 45mm

Forward IS-30-5110 1-37510-035-0 1982- 45mm 155mm 1-37510-105-0 1984- 45mm 155mm

4-5 tonne 7 tonne

687-50 SERIES 6-613-550100690 55mm 200mm

Suits shafts with Hi-Torqueflanges

F SERIES IS-30-7150 9-37516045-1 1988- 50mm No Seals

Hex Solid Rubber

N SERIES IS-30-5620 5-37510-008-0 32mm IS-30-5610 5-37510-007-0 1985- 40mm

4 Hole bracket

IS-30-7170 1-37510093-0 55mm 295mm

D MAX IS-30-7160 8-97942877-0 30mm 94mm 4X4


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-20

ISUZU


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-21

RUJ-2508 28.00 48.00 SIDE 2 1.102 1.890

RUJ-2050 28.00 53.00 SIDE 2 1.102 2.087

RUJ-2052 28.00 53.00 NIL 2 HOLE IN CROSS 1.102 2.087

RUJ-2509 29.50 56.00 SIDE 2 1.161 2.205

K5-A611 30.00 81.80 CENTRE 1 MERCEDES SPRINTER

1.181 3.220 REPLACEMENT

K5-A728 30.20 81.80 CENTRE 1 MERCEDES SPRINTER 1.189 3.220 REPLACEMENT

K5-A773 34.00 89.00 CENTRE 1 UNIMOG

1.339 3.504

RUJ-3005 38.00 62.00 CENTRE 2 1.496 2.441

K5-A675 38.00 89.20 NIL 1 UNIMOG 1.496 3.512

RUJ-5001 42.00 72.00 CENTRE 2 1.654 2.835

RUJ-3005 42.00 84.00 CENTRE 2 1.654 3.307

K5-A606 45.00 120.40 CENTRE 1 1.772 4.740

RUJ-5002 42.00 84.00 CENTRE 2 1.654 3.307

K5-A633 48.00 126.00 CENTRE 1 385 SERIES 1.890 4.961

K5-A658 53.00 135.00 CENTRE 1 389 SERIES 2.087 5.315

K5-A775 68.00 95.00 CENTRE 2 385.60 656 SERIES 2.677 3.740

K5-A802 68.00 123.00 CENTRE 2 385.65 659 SERIES 2.677 4.843

Mercedes Benz also use GWB driveshafts. Refer to GWB section of catalogue.

PART No. C B1 B2 LUBE FIG. U.J. BRACKET STYLE

MERCEDES BENZ UNIVERSAL JOINT KIT

MERCEDES BENZ

FIGURE 1 FIGURE 2

C B1 B1 C B2


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-22

MERCEDES BENZ

SLIP CAP INVOLUTE C/L TOTAL MAX. TUBE U.J. SERIES ASSEMBLY DIA. SPLINE TO WELD SLIP ANGLE O.D. & WALL PART No. O.D. & No. POINT THICKNESS P A L C

FIGURE 1

MERCEDES BENZ SLIP ASSEMBLY

FLANGE FIG CAP C/L OF FLANGE SPIGOT P.C.D. BOLT No. HOLE U.J. SERIES OEM REF. YOKE DIA. U.J. DIA. DIA. HOLE HOLES DIA. PART No. PART No. TO FACE F=FEMALE PATTERN P L C S M M

MERCEDES BENZ FLANGE YOKE

MB-2-611 1 30.0 48.0 120.0 F-57.00 101.5 EQUALLY 4 10.0 K5-A611 Mercedes 25deg 1.181 1.890 4.724 F-2.244 3.996 SPACED 0.472 Sprinter MB-2-728 1 30.2 48.0 120.0 F-57.00 101.5 EQUALLY 4 10.0 K5-A728 Mercedes 1.189 1.890 4.724 F-2.244 3.996 SPACED 0.472 Sprinter MB-2-728-2 1 30.2 48.0 120.0 F-57.00 101.5 66x78 4 10.0 K5-A728 Mercedes 1.189 1.890 4.724 F-2.244 3.996 0.472 Vito MB-2-728-1 1 30.2 58.0 132.0 F-67.00 112.00 85x72 4 10.0 K5-A728 Mercedes 1.189 1.890 5.197 F-2.244 4.409 0.472 Sprinter MB-2-180 38.0 48.0 100.0 F-50.00 40x69 4 10.0 K5-A675 Unimog 8mmkey 1.496 1.890 3.937 F-1.969 0.472 across yoke MB-2-158 1 48.0 75.0 150.0 F-90.00 130.0 EQUALLY 8 12.0 K5-A633 385 3854111711 1.890 2.953 5.906 F-3.543 5.118 SPACED 0.472 MB-2-158XS 2 48.0 75.0 154.0 130.0 4 13.0 K5-A633 385 6504110111 1.890 2.953 6.063 5.118 0.512 MB-2-117 2 53.0 86.0 165.0 F-95.00 140.0 EQUALLY 8 12.0 K5-A658 389 3874110011 2.087 3.386 6.496 F-3.740 5.512 SPACED 0.472 MB-2-117-1XS 2 53.0 85.0 154.0 130.0 4 13.0 K5-A658 389 2.087 3.346 6.063 5.118 0.512 2-286-372717500 53.0 97.0 165.0 140.0 4 13.0 K5-A658 389 3894110411 2 2.087 3.819 6.496 5.512 0.512 MB-2-117XS 2 53.0 97.0 180.0 150.0 4 15.0 K5-A658 389 2.087 3.819 7.087 5.906 0.591 MB-2-656XS 2 68.0 100.0 180.0 150.0 4 15.0 K5-A775 Actros 6564110311 2.677 3.937 7.087 5.906 SPACED 0.591 385-60 MB-2-802XS 2 68.0 113.0 200.0 165.0 4 15.0 K5-A802 Actros 2.677 4.449 7.874 6.496 0.591 385-65

MB-83-180 38.0 38 x 2.5 x 16 Spline 237.0 100.0 30 52X4MM K5-A675 Unimog 1.496 9.331 3.937 52.00 x 4.00 MB-83-158 48.0 65 x 2.5 x 24 Spline 327.0 110.0 24 90X4MM K5-A633 385 1.890 12.874 4.331 90.00 x 4.00 MB-83-117 53.0 72 x 2.5 x 27 Spline 373.0 150.0 25 100X5MM K5-A658 389 2.087 14.685 5.906 100.00 x 5.00 MB-83-656 68.0 80 x 2.5 x 25 Spline 400.0 160.0 22 140X5MM K5-A775 Actros 2.677 15.748 6.299 140.00 X 5.00 385-60 MB-83-802 68.0 369.0 140X5MM K5-A802 Actros 2.677 14.528 140.00 X 5.00 385-65

FIGURE 2

P

P


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-23

MB-2-180 K5-A675 MB-83-1180 52X4MM MB-26-180 Unimog 350 52.00 x 4.00 MB-2-158 K5-A633 MB-83-158 90X4MM MB-26-158 385 90.00 x 4.00 MB-2-117 K5-A658 MB-83-117 100X5MM MB-26-117 389 100.00 x 5.00 MB-2-158XS K5-A633 MB-83-158 90X4MM MB-26-158 385 90.00 x 4.00 MB-2-117XS K5-A658 MB-83-117 100X5MM MB-26-117 389 100.00 x 5.00 MB-2-656XS K5-A775 MB-83-656 140X5MM MB-26-656 Actros 140.00 x 5.00 385-60 MB-2-802XS K5-A802 MB-83-802 144X7MM MB-26-802 Actros 144.00 x 7.00 385-65

MERCEDES BENZ

WELD YOKE CAP DIA. C/LINE TO TUBE O.D. & WALL MAX U.J. SERIES OEM REF. PART No. POINT OF WELD THICKNESS ANGLE PART No. P L B

MB-26-611 30.0 53.0 70X2MM K5-A611 Mercedes 1.181 2.087 70.00 x 2.00 Sprinter

MB-26-728 30.2 58.5 2013-0000 K5-A728 Mercedes 1.189 2.303 2.500 x 0.095 Vito

420-26-200* 30.2 45.0 2413-0000 25 K5-A728 Mercedes 1.189 1.772 3.000 x 0.095 Sprinter

MB-26-180 38.0 70.0 52X4MM 30 K5-A675 Unimog 1.496 2.756 52.00 x 4.00

MB-26-158 48.0 101.0 90X4MM 25 K5-A633 385 3854113805 1.890 3.976 90.00 x 4.00

MB-26-117 53.0 116.0 100X5MM 25 K5-A658 389 3894111805 2.087 4.567 100.00 x 5.00

MB-26-656 68.0 145.0 140X5MM K5-A775 Actros 2.677 5.709 140.00 x 5.00 385-60

MB-26-802 68.0 140.0 144X7MM K5-A802 Actros 2.677 5.512 144.00 x 7.00 385-65

MERCEDES BENZ WELD YOKE

FLANGE U.J. SLIP TUBE WELD SERIES YOKE PART No. ASSEMBLY SIZE YOKE PART No. PART No. PART No. A B C D E

MERCEDES BENZ TUBULAR TYPE ASSEMBLY

P

A B C D E B A

*Can use 2-687-204000000.


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-24

COMPANION FIG. LENGTH SPLINE FLANGE SPIGOT P.C.D. BOLT No. HOLE SERIES FLANGE DIA. & No. DIA. DIA. HOLE HOLES DIA. PART No. M=MALE PATTERN L1

MERCEDES BENZ

MERCEDES BENZ COMPANION FLANGE

MIDSHIP SPLINE END OF BEARING TUBE CENTRE COMPANION SERIES STUB DIA. & No. SPLINE TO I.D. O.D. & WALL BEARING FLANGE PART No. POINT OF THICKNESS PART No. WELD L B O

*MB-57-158 55 x 2.5 x 20 Spline 120.0 55.0 90X4MM MB-15855 MB-1-158 385 4.724 2.165 90.00 x 4.00 *MB-57-158 55 x 2.5 x 20 Spline 120.0 55.0 90X4MM MB-15855 MB-1-158XS 385 4.724 2.165 90.00 x 4.00 *MB-57-117 60 x 2.5 x 22 Spline 148.0 60.0 100X5MM MB-11760 MB-1-117XS 389 5.827 2.362 100.00 x 5.00 **MB-56-656 70 x 2.5 x 26 Spline 148.0 70.0 140X5MM MB-30-9096 MB-1-656XS# Actros 5.827 2.756 140.00 x 5.00 144X7MM MB-1-802XS# 144.00 x 7.00 MB-83-611^ 38 x 18 Spline 207.0 Comp. 45.0 70X2MM MB-30-9025 N/A Sprinter Suit UJ K5-A611 8.150 1.772 70.00 x 2.00 Sleeve Assy MB-83-728^ 38 x 18 Spline 215.0 Comp. 45.0 2413-0000 MB-30-9025 N/A Sprinter Suit UJ K5-A728 8.464 1.772 3.000 x 0.095 Sleeve Assy MB-83-728-1^ 38 x 18 Spline 215.0 Comp. 47.0 2413-0000 MB-30-9223 N/A Sprinter Suit UJ K5-A728 8.464 1.850 3.000 x 0.095 Sleeve Assy * MIDSHIP STUBS USE M16 X 1.5 BOLT 1-113-608217060 & WASHER 1-113-605017060. TIGHTENING TORQUE = 250Nm **MIDSHIP STUBS USE M20 X 1.5 BOLT - 1-113-708217060, 20mm Washer - 1-113-705017060. TIGHTENING TORQUE = 445Nm #USE SLINGER PART No. MB-413-0061. SPACER USED BETWEEN BEARING & COMP. FLANGE MB-411-0052

MERCEDES BENZ MIDSHIP ASSEMBLY

MB-1-158 1 82.0 55 x 2.5 x 20 Spline 150.0 M-90.00 130.0 EQUALLY 8 12.0 385 3.228 5.906 M-3.543 5.118 SPACED 0.472 MB-1-158XS 2 82.0 55 x 2.5 x 20 Spline 150.0 130.0 4 13.0 385 3.228 5.906 5.118 0.512 MB-1-117XS 2 99.0 60 x 2.5 x 22 Spline 180.0 150.0 4 15.0 389 3.898 7.087 5.906 0.591 MB-1-656XS 2 99.0 70 x 2.5 x 22 Spline 180.0 150.0 4 15.0 Actros 3.898 7.087 5.906 0.591 385.60 MB-1-802XS 2 101.1 70 x 2.5 x 26 Spline 200.0 165.0 4 15.0 Actros 3.980 7.874 6.496 0.591 385.65

FIGURE 1 FIGURE 2

L

O

B

^MB-47000X - Boot kit to suit included.


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-25

MERCEDES BENZ

11

MERCEDES BENZ SPRINTER DRIVEHAFTS

MB-2-611 K5-A611 MB-26-611 MB-83-611 MB-30-9025 MB-47000X 120OD - 4x10mm 30 x 81.80 suits 70x2mm tube Includes MB-47000X boot kit 45mm MB-2-728 K5-A728 MB-26-728^ MB-83-728 MB-30-9025 MB-47000X 120OD - 4x10mm 30.20 x 81.80 suits 2.5 swaged tube Includes MB-47000X boot kit 45mm MB-2-728-2 K5-A728 MB-26-728^ MB-83-728-1 MB-30-9223* MB-47000X 120OD - 4x10mm 30.20 x 81.80 suits 2.5 swaged tube Includes MB-47000X boot kit 47mm

FLANGE U.J. WELD SLIP ASSEMBLY BEARING BOOT YOKE PART No. YOKE PART No. PART No. KIT PART No. PART No. PART No. 1 6 2 5 3 4

L

D1 D2

BOOT KIT LENGTH INTERNAL DIA. MINOR DIA. LARGE CLAMP SMALL CLAMP PART No. Part No. Part No. L D1 D2

MB-47000X 95.00 55.00 45.00 MB-84200 *NSS MB-84100 *NSS

3.740 2.165 1.772 55mm 45mm4WD HILUX, 4 ER

MERCEDES BENZ SLIP YOKE BOOT KIT

*NSS - Boot clamps are not sold separately

^ Can use 2-687-204000000 weld yoke which suits 3 x 0.095.* Suits later model Sprinter.Note:ThefixedjointmidshipassemblyforthethreepieceMercedesshaftisnotavailable.

1 13 652 66

1

42 6 2 23


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-26

MERCEDES BENZ CENTRE BEARING ASSEMBLY

# INDENT ONLY

Sprinter (New) MB-30-9223 47mm 194mm


W201 Series MER-30-6200 2014100581 82-93 25mm 110.5mm 190E 85-93 190D 86-89

W126, C126 MER-30-6190 1264100181 79-91 30mm 120mm 380SEL 82-83

W124, W126 MER-30-6180 1244100281 71-93 30mm 116mm 350E, D 86-

Sprinter MB-30-9025 901-410-0312 45mm 194mm

W123 MER-30-6940 1234101081 30mm 131mm 230 77-78 280 77-81 300D 76-82 300TD 82-85 380SL 82-85

W124, C124, S124, MER-30-6950 1244100181 84-93 25mm 118mm 260E 88-90

Vito MB-30-0281 6394100281 30mm 148mm Rear "D" Shape

Vito MB-30-0081 6394100081 30mm 148mm Front "O" Shape

MERCEDES BENZ


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-27


Atego D Shape Bearing MB-30-9023 45mm 35mm M12.5x1.5

Actros MB-30-9096 656-411-0112 70mm 35mm M12.5x1.5

Atego D Shape Bearing MB-30-9141 55mm 35mm M12.5x1.5

Atego D Shape Bearing MB-30-9143 654-411-0012 60mm 35mm M12.5x1.5

395 Series MB-30-9015 395-410-0622 70mm 242mm Wide Housing

MB-30-9139 70mm

22mmWideBearing

25mmWideBearing

389 Series MB-11760 389-410 0222 60mm 50mm 247mm Wide Housing

Truck Suits 385 Series (Octagonal Style) MB-30-9009 45mm 27mm

Truck Suits 385 Series (New Shape) MB-15855 385-410-0922 55mm 27mm 190mm Wide Housing

25mmWideBearingReplaces Octagonal

shape

MERCEDES BENZ CENTRE BEARING ASSEMBLY

MERCEDES BENZ


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-28

MERCEDES BENZ


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-29

MITSUBISHI

FIGURE 1 FIGURE 2

C B1 CB1 B2

MITSUBISHI UNIVERSAL JOINT KITPart No. C B1 B2 FIG. LUBE DESCRIPTION

RUJ-1501 22.00 40.00 2 NIL Fork lift hydraulic drive0.87 1.57

K5-A652 22.06 61.80 1 NIL Staked joint.087 2.43

K5-A556 25.00 63.80 1 SIDE0.98 2.51

RUJ-2045 25.00 76.50 1 SIDE Triton/Scorpion0.98 3.01

K5-A558 25.00 77.00 1 SIDE0.98 3.03

K5-A559 25.00 77.80 1 SIDE0.98 3.06

K5-A561 27.00 65.30 1 SIDE1.06 2.57

K5-A562 28.50 78.00 1 CENTRE1.12 3.07

RUJ-3006 30.00 58.30 2 SIDE Canter 4WD/Pajero1.18 2.30

RUJ-4010 30.00 74.20 2 SIDE Pajero1.18 2.92

K5-A585 30.00 78.20 1 CENTRE Canter1.18 3.08

K5-A563 31.70 102.00 1 CENTRE Canter1.25 4.02

K5-A569 36.00 104.00 1 CENTRE1.42 4.09

K5-A572 38.00 104.00 1 CENTRE1.50 4.09

K5-A684 38.00 110.00 1 SIDE1.50 4.39

K5-A759 40.00 111.00 1 CENTRE1.57 4.37

K5-A576 44.00 129.00 1 CENTRE1.73 5.08

K5-A784 44.00 131.00 1 CENTRE MC9986801.73 5.16

K5-A578 46.00 142.00 1 CENTRE1.81 5.59

K5-A586 46.00 148.00 1 CENTRE1.81 5.83

K5-A584 52.00 154.00 1 CENTRE2.05 6.06

K5-A670 52.00 160.00 1 CENTRE2.05 6.30


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-30

MITSUBISHI


M S B1

L

C

FIGURE 1

MI-2-238 2 30.00 58.30 45.0 M-60.00 90.0 58.0x69.0 4 10.0 RUJ-3006 1.18 2.30 1.772 M-2.362 3.543 0.394

MI-2-059 1 30.00 78.20 45.0 M-60.00 90.0 58.0x69.0 4 10.0 K5-A585 1.18 3.08 1.772 M-2.362 3.543 0.394

3-2-352-75M 1 30.16 92.07 40.0 M-75.00 100.0 64.0x77.0 4 12.2 5-178X 1.19 3.63 1.575 M-2.953 3.937 0.480

MI-2-352 1 31.70 102.00 45.0 M-70.00 100.0 64.0x77.0 4 12.0 K5-A563 1.25 4.02 1.772 M-2.755 3.937 0.472

MI-2-578 3 46.00 142.00 70.0 M-90.00 83.0x122.0 4 14.2 K5-A578 1.81 5.59 2.755 M-3.543 0.559

MI-2-584# 3 52.00 154.00 90.0 M-90.00 156.0 80.0x134.0 4 16.2 K5-A584 2.05 6.06 3.543 M-3.543 6.142 0.638

5-2-180414# 3 47.63 134.94 70.0 M-90.00 83.0x122.0 4 14.2 5-279X 1.73 5.08 2.755 M-3.543 .559

6-2-192416# 3 49.21 154.78 90.0 M-90.00 156.00 80.0x134.0 4 16.2 5-280X 1.93 6.09 3.543 M-3.543 6.142 0.638

6-2-203613# 3 49.21 154.78 M-120.00 180.0 6 5-280X 1.93 6.09 M-4.724 3.937

MITSUBISHI FLANGE YOKE

FIGURE 2

C

SM

L

B2

FIGURE 3

# INDENT ONLY


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-31


Dust Cap Kit = PART No DCKMI1

C

B1

L

FIGURE 2

C

B2

L

FIGURE 1

MI-3-252KX 2 30.00 58.30 38.50-24 174.0 MI-40-110 RUJ-3006 Dust cap kit included 1.18 2.30 1.515 6.85

MI-3-3006 2 30.00 58.30 38.10-16 174.0 K3-42-A3631 RUJ-3006 Spicer series splines 1.18 2.30 1.500 6.85

MI-3-069KX 3 30.00 78.20 38.50-24 174.0 MI-40-110 K5-A585 Dust cap kit included 1.18 3.08 1.515 6.85

MI-3-A585 3 30.00 78.20 38.10-16 174.0 K3-42-A3631 K5-A585 Spicer series splines 1.18 3.08 1.500 6.85

MI-3-010KX 3 31.70 102.00 38.50-24 165.0 MI-40-110 K5-A563 Dust cap kit included 1.25 4.02 1.515 6.50

MI-3-A563 3 31.70 102.00 38.10-16 165.0 K3-42-A3631 K5-A563 Spicer series splines 1.25 4.02 1.500 6.50

MITSUBISHI SLIP YOKE

B

MITSUBISHI

FIGURE 3

L

C

B1

G


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-32

STUB PART No. SPLINE DIA. & No. SPLINE TYPE LENGTH OF END OF SPLINE TUBE O.D. & SPLINE TO POINT OF THICKNESS WELD B G L T

G

B

L

T

MI-40-110 38.50-24 STEEL 94.5 177.0 1.515 3.720 6.969 64.00 x 2.20

K3-42-A3631 38.10-16 COATED 65.0 195.0 65X1-6MM 1.500 2.550 7.677 65.00 x 1.60

MI-40-576-1* 54.00-16 COATED 90.0 300.0 90X4MM 2.126 11.811 90.00 x 4.00

MITSUBISHI STUB

MITSUBISHI

*Available while stock lasts.


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-33

MITSUBISHI

BUTT TYPE H=HOLLOW, S=SOLID

B1 T

C

FIGURE 1

B2 T

C

FIGURE 2

WELD YOKE FIG. U.J. DIMENSIONS C/LINE TO TUBE BUTT TYPE U.J. PART No. POINT OF O.D. & WALL PART No. WELD THICKNESS C B1 B2 L T I

MI-28-225 2 30.00 58.30 48.0 H RUJ-3006 1.18 2.30 1.890 64.00 x 2.20

MI-28-066 1 30.00 78.20 48.0 H K5-A585 1.18 3.08 1.890 64.00 x 2.20

MI-28-120 1 31.70 102.00 48.0 H K5-A563 1.25 4.02 1.890 64.00 x 2.20

MI-28-584# 3 52.00 154.00 102.0 100X4MM H K5-A584 2.05 6.06 4.02 100.00 x 4.00

MITSUBISHI WELD YOKE

L L

MITSUBISHI MIDSHIP ASSEMBLY ASSEMBLY FIG SPLINE TUBE END OF LENGTH CENTRE BRG COMP COMMENTS PART No. DIA. & No. SPLINE TO OF SPLINE BEARING DIA FLANGE POINT OF WELD D L G H

MI-56-352 1 39.67-18 2413-0000 107.0 46.0 MI-30-6020 40 MI-1-352 INCL NUT & 1.562 76.20 x 2.41 4.213 1.811 NOT INCL. INCL. WASHER

T

FIGURE 3

L

C

B1

# INDENT ONLY


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-34

MITSUBISHI

MITSUBISHI COMPANION FLANGES COMPANION FIG. LENGTH SPLINE FLANGE SPIGOT P.C.D. BOLT No. HOLE SERIES FLANGE DIA. & No. DIA. DIA. HOLE HOLES DIA. PART No. M=MALE PATTERN L1

MI-1-352* 1 70.00 39.67 x 18 Spline F-70.00 100 64 x 77 4 12.2 2.756 1.562 x 18 2.756 3.973 0.480

FIGURE 1 FIGURE 2

L1B1

B2

VEHICLE ASSEMBLYPART No.

SPIGOTDIA.

F

BOLT HOLEPATTERN

B1 x B2

BOLTHOLEDIA.

P.C.D.

E

BUTTDIA.

MMITSUBISHI CANTER 800-R2570 M-60.00 58.00 x 69.00 10.10 90.00 46.20

2.362 2.283 x 2.717 0.398 3.543 1.819

F M

MITSUBISHI DOUBLE CARDAN CV JOINT

*PartisnolongeravailableseparatelyuseMI-56-352 assembly as replacement.


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-35

FLANGE U.J. U.J. DIMENSIONS SLIP YOKE STUB TUBE SIZE WELD YOKE YOKE PART No. FEMALE MALE PART No. PART No. PART No. PART No. C B1 B2

MI-2-238 RUJ-3006 30.00 58.30 MI-3-252KX MI-40-110 MI-28-225 1.18 2.30 64.00 x 2.20

MI-2-059 K5-A585 30.00 78.20 MI-3-069KX MI-40-110 MI-28-066 1.18 3.08 64.00 x 2.20

MI-2-352 K5-A563 31.70 102.00 MI-3-010KX MI-40-110 MI-28-120 1.25 4.02 64.00 x 2.20

MITSUBISHI CANTER

MITSUBISHI TUBULAR SHAFT ASSEMBLY

MITSUBISHI


Canter MI-30-5630 MB000076 80-89 35mm 170mm MB000083 MB563228 85-89 35mm 170mm

L200 MI-30-5730 MB154080 79- 30mm 165mm Scorpion

GALANT 2 per Vehicle MI-30-6930 MB505495 30mm 190mm HH VR TURBO LANCER EVO (Some)

MITSUBISHI CENTRE BEARINGS

Lancer EVO MI-30-7010 97- 30mm N/A Bearing and Rubber Only


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-36

MITSUBISHI


Without seals

FK415, 515 MI-30-6040 MC824410A 45mm

FUSO MI-30-6030 MC881040A 55mm

MITSUBISHI CENTRE BEARINGS

Triton 2WD MI-30-4510 MB154199 86- 30mm 160mm MR357998

Triton 4WD MI-30-4610 MB154706 86- 30mm 160mmWith seals

FE439, FE444 MI-30-6020 MB563234A 40mm 170mm FE449

L300 4WD MI-30-4510A MR165252 98- 30mm 160mm Star Wagon (25mm Holes)

Triton 2WD MI-30-7020 MB580647 05- 30mm 160mm KA4T, KB4T 4WDML


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-37

RUJ-2028 28.00 55.96 3 SIDE MQ Nissan Patrol 1.10 2.20

RUJ-3007 32.00 68.00 3 CENTRE GU Nissan Patrol 1.26 2.68

K5-A564 32.00 107.00 1 SIDE INCL 4 LOCK TABS 1.26 4.21 REUSE BOLTS & PLATES K5-A568 35.50 119.00 1 CENTRE 1.40 4.69

K5-A575 43.00 128.00 56.00 2 CENTRE UD 1.69 5.04 2.20

K5-A547 43.00 136.00 56.00 2 CENTRE UD 1.69 5.35 2.20

K5-A548 55.00 164.00 68.00 2 CENTRE UD 2.17 6.46 2.68

K5-A695 63.50 178.00 2 CENTRE UD 2.50 7.01

NISSAN

Part No. C B1 B2 / E FIG. LUBE DESCRIPTION

FIGURE 1

C B1

NISSAN UNIVERSAL JOINT KITFIGURE 2

Cap Type(Lock Plate)

FIGURE 3


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-38

NISSAN


M S B1

L

C

FIGURE 1

2-2-1309 1 26.99 81.76 45.0 M-50.00 81.0 57.4 x 57.4 4 K5-13XR 2.17 6.46 1.772 M-1.969 3.227 Navara,300ZX

2-2-1169 1 26.99 81.76 46.0 M-65.00 95.1 67.2 x 67.2 4 12 K5-13XR 2.17 6.46 1.811 M-1.969 3.774 MQ Patrol

UD-2-100 35.5 119.00 56.0 F-85.00 113.0 86.6 x 72.6 4 12.2 K5-A568 1.40 4.69 2.205 F-3.346 4.449 0.480

UD-2-A1179 3 43.0 136.00 68.5 F-90.00 140.0 80 x 115 4 16.4 K5-A547 1.69 5.35 2.697 F-3.543 5.512 0.646

UD-2-0064# 3 43.0 136.00 86.5 F-90.00 170.0 105 x 134 4 16.4 K5-A547 1.69 5.35 3.406 F-3.543 6.693 0.646

UD-2-A1189 3 55.0 164.00 75.0 F-90.00 170.0 105 x 134 4 16.4 K5-A548 2.17 6.46 2.953 F-3.543 6.693 0.646

NISSAN FLANGE YOKEFIGURE 2 FIGURE 3

C

SM

L

B2

# INDENT ONLY


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-39

SLIP YOKE FIG. DIMENSIONS SPLINE C/LINE TO LENGTH STUB U.J. PART No. PART No. O.D. & No. END OF THROUGH PART No. SPLINE HOLE C B1 B2 B L G

NP-3-3007 2 32.00 68.00 38.10-16 190.00 160.00 K3-42-A1151 RUJ-3007 1.26 2.68 1.500 7.48 6.30 Nissan Patrol

UD-3-105KX 35.50 119.00 45.00-16 222.0 170.00 UD-53-104 K5-A568 1.40 4.69 1.77 8.74 6.69

UD-3-A3371KX 1 43.00 136.00 54.20-16 212.0 158.00 UD-42-A1841 K5-A547 1.69 5.35 2.13 8.35 6.22 Dust cap DCKUD3


UD-3-A3391KX# 1 55.00 164.00 60.40-18 140.0 100.00 UD-42-A1631 K5-A548 2.17 6.46 2.38 5.51 3.94 Dust cap DCKUD1


UD-3-548KX 1 55.00 164.00 75.00-18 300.0 240.00 UD-42-548 K5-A548 2.17 6.46 2.95 11.81 9.45

NISSAN SLIP YOKE

NISSAN

FIGURE 1

L

C

B1

G C

L

FIGURE 2

B2B

STUB PART No. SPLINE DIA. & No. TUBE LENGTH OF END OF SPLINE SUITS SLIP O.D. & WALL SPLINE TO POINT OF YOKE PART No. THICKNESS WELD S O G L

UD-42-A1631# 59.40 x 18 112.0 168.5 UD-3-A3391KX 2.338 4.409 6.634

UD-42-A1841 54.20-16 90X4MM 160.0 206.0 UD-3-A3371KX 2.134 90.00 x 4.00 6.299 8.110

UD-42-548 75.00 x 18 3603-0000 108.0 300.0 UD-3-548KX 2.953 114.30 x 6.58 4.252 11.811

NISSAN UD STUBS

S

L

T

G

# INDENT ONLY


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-40

WELD YOKE FIG. U.J. DIMENSIONS C/LINE TO TUBE O.D. BUTT U.J. PART No. POINT OF & WALL DIAMETER PART No. WELD THICKNESS C B1 B2 L T

UD-26-107 1 35.50 119.00 54.0 86.30 K5-A568 1.40 4.69 2.126

UD-26-A2407 1 43.00 136.00 72.5 90X4MM 82.00 K5-A547 1.69 5.35 2.854 90.00 x 4.00

UD-26-A2117 1 55.00 164.00 79.5 93.40 K5-A548 2.17 6.46 3.130

NISSAN UD WELD YOKE

NISSAN

NISSAN UD MIDSHIP STUBS STUB FIG SPLINE TUBE END OF LENGTH CENTRE BRG COMP NOTES PART No. DIA. & No. O.D. & WALL SPLINE TO OF SPLINE BEARING DIA FLANGE THICKNESS POINT OF OR WELD SLIP YOKE S T L G B

UD-53-104 2 45.00 x 16 306.0 111.0 UD-30-5530 50 UD-3-105KX 1.772 12.047 4.370 Slip Yoke

UD-42-A1641 2 59.40 x 18 308.0 175.0 UD-30-5550 60 UD-3-A3401KX 2.338 12.126 6.890 Slip Yoke

UD-42-A1851 2 54.20-16 90X4MM 282.0 163.0 UD-30-5540 55 UD-3-A3371KX 2.134 90.00 x 4.00 11.102 6.417 Slip Yoke

T

FIGURE 1

L

C

B1

FIGURE 1 FIGURE 2

S

L

T

GS

L

T


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-41

NISSAN

ASSEMBLY U/JOINT U.J. DIMENSIONS FLANGE FLANGE FLANGE NOTES PART No. PART No. PART No. SPIGOT DETAILS C B1 B2

UD-PSA-000 K5-A568 35.50 119.00 - UD-2-100 85.00mm F 113.00 PCD VARIOUS 1.40 4.69 - 72.60 x 86.60 LENGTHS

NISSAN TUBULAR SHAFT ASSEMBLY

L1B1

B2

VEHICLE ASSEMBLYPART No.

SPIGOTDIA.

F

BOLT HOLEPATTERN

B1 x B2

BOLTHOLEDIA.

P.C.D.

E

BUTTDIA.

MNISSAN MQ PATROL 800-R2590 M-50.00 57.20 x 57.20 10.30 81.28 46.20

1.968 2.252 x 2.252 0.406 3.200 1.819

NISSAN GQ PATROL 800-R2580 M-65.00 67.20 x 67.20 12.10 95.00 38.502.559 2.646 x 2.646 0.476 3.740 1.516

F M

NISSAN DOUBLE CARDAN CV JOINT

ASSEMBLY U/JOINT U.J. DIMENSIONS FLANGE FLANGE FLANGE NOTES PART No. PART No. PART No. SPIGOT DETAILS C B1 B2

UD-JSA-000 K5-A568 35.50 119.00 - UD-2-100 85.00mm F 113.00 PCD VARIOUS 1.40 4.69 - 72.60 x 86.60 LENGTHS

NISSAN CENTRE BEARING SHAFT ASSEMBLY

Note:Centrebearingbracketpartnumberis37521-90006


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-42

NISSAN NISSAN CENTRE BEARINGS


720 NP-30-A3710 37521-01W25 79-85 30mm E20

720G. 720S.720

(2WD & 4WD)

300ZX NP-30-5010 37521-33P27 89- 30mm 144mm Aus Production

NP-30-5820 37521-33P25 89- 30mm 144mm Jap Import

300ZX

620 NP-30-5720

300ZX NP-30-6260 89- 30mm Skyline / Laurel R32-R33

BEARING AND RUBBER

Skyline / Laurel NP-30-6250 30mm 155mm R32-R33


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-43

NISSAN

Bluebird NP-30-A3410 37521-W1025 -6/83 30mm Navara 37521-W1025 9/85- 30mm Skyline 37521-Q0125 81-86 30mm Stanza 37521-41L25 87- 30mm Pintara 86-90 300ZX 84-89

4 spd manual2WD

Japanese Production 280C RD28. CA180D. 180DT

5 spd manual Bluebird 17R-30-2610 37521-V9625 -6/82 30mm Stanza 78-83 30mm 200B 79-81 30mm

Skyline CB-952 37521-J7085 7/86- 30mm R31

Australian Production

UD UD-30-5540 37510-Z2002 55mmDiesel truck

55mm

UD UD-30-5550 37510-90017 60mmDiesel truck

60mm


Navara NP-30-7040 37522-JR60A 05- 45mm 168mm D40 2WD 19mm wide

4WD

UD UD-30-5530 37510-Z5002 50mmDiesel truck

50mm

Navara NP-30-A3510 37521-32G25 8/87- 30mm 37521-33G25 37521-56G25

Centreheight57mm

NISSAN CENTRE BEARINGS


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-44

NISSAN


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-45

K5-A645 38.00 148.00 1 SIDE P30, P300 TAPERED BRACKETS 1.496 5.827

K5-A596 44.00 149.00 2 CENTRE T60 NO BRACKETS 1.732 5.866

K5-A598 48.00 161.00 1 CENTRE T61 STRAIGHT BRACKETS 1.890 6.339

K5-A599 48.00 161.00 1 CENTRE P40, P400 TAPERED BRACKETS 1.890 6.339 Some applications have M16x2 threaded taper brackets.

K5-A597 50.00 164.00 2 CENTRE T70 NO BRACKETS 1.969 6.457

K5-A600 57.00 164.00 1 CENTRE T71 STRAIGHT BRACKETS 2.244 6.457

K5-A601 57.00 164.00 1 CENTRE P50, P500 TAPERED BRACKETS 2.244 6.457

K5-A768 57.00 164.00 1 CENTRE P500 TAPERED BRACKETS TO GWB 687-55 2.244 6.457 57.00 152.06 2.244 5.987

K5-A756 65.00 190.00 2 CENTRE P600 NO BRACKETS 2.559 7.480

PART No. C B1 FIG. LUBE SERIES / U.J. BRACKET STYLE

SCANIA UNIVERSAL JOINT KIT

SCANIA

FIGURE 1

FIGURE 2

FIGURE 3

C

B1

C

B1

4.5

4.5


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-46

SCANIA

SLIP ASSEMBLY FIG. CAP DIA. DISTANCE ACROSS SPLINE C/L OF U.J. TOTAL SLIP TUBE O.D. SERIES PART No. YOKE EARS O.D. & No. TO WELD & WALL POINT THICKNESS P A S L C B

SC-83-300# 1 38.0 158.0 68 x 26 SPLINE 274.0 110.0 90 x 5 P300 1.496 6.220 10.787 4.331

SC-83-400 1 48.0 183.0 68 x 26 SPLINE 298.0 110.0 100 x 5 P400 1.890 7.205 11.732 4.331

SC-83-500 1 57.0 175.0 79 x 30 SPLINE 312.00 120.0 108 x 5.5 P500 2.244 6.890 12.283 4.724

SC-83-520 1 57.0 175.0 79 x 30 SPLINE 385.00 160.0 92 x 5 P520 2.244 6.890 15.157 6.299 W/ANGLE

SC-83-600 1 65.0 190.0 80 x 34 SPLINE 400.00 130.0 114.3 x 5.5 P600 2.559 7.480 15.748 5.118

SC-83-60 1 44.0 159.0 54.2 x 20 SPLINE 332.00 120.0 90 x 5 T60 2.559 6.260 13.071 4.724

SC-84-70 2 50.0 164.0 62.05 x 12 SPLINE 307.00 100.0 95 x 5 T70 1.968 6.456 12.086 3.937

FIGURE 1

SCANIA SLIP ASSEMBLY

# INDENT ONLY

L

A

S

B

P

B

FIGURE 2

FIGURE 1

SCANIA FLANGE YOKE

P

FLANGE YOKE

PART No.

CAPDIA.

C

C/L OF U/J TO FACE

M

FLANGEDIA.

A

P.C.D.

B

BOLT HOLEPATTERN

HOLE QTY

HOLE DIA.

H

U/J PART No.

OEM REF#

SC-2-600-KV * 65.002.559

100.003.937

208.008.189

180.007.086

132.50 x 121.405.217 x 4.779

4 15.100.594

K5-A756 1531005

* Flange has 2 x threaded holes on 155mm PCD and 2 dowel holes on 186mm PCD


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-47

STUB SPLINE DIA. SPLINE LENGTH OF END OF SPLINE TUBE SLIP YOKE SERIES PART No. & No. TYPE SPLINE TO POINT SIZE PART No. OF WELD D G L O

SC-3-61 48.0 170.0 56.29-24 270.0 SC-42-61 T61 / P40 1.890 6.693 2.216 10.63

SCANIA

SLIP YOKE CAP DIA. DISTANCE ACROSS SPLINE C/LINE TO STUB SERIES PART No. YOKE EARS O.D. & No. END OF SPLINE PART No. P A B L

SC-42-61 56.29-24 STEEL 111.0 256.0 100X5MM SC-3-61 T61 / P40 2.216 4.370 10.079 100.00 x 5.00

*SC-42-70 62.0-12 STEEL 110.0 261.0 SC-3-70 T70 2.442 4.331 10.276 95.00 x 5.00 *Available while stock lasts - Use SC-84-70

SCANIA SLIP YOKE

SCANIA STUB

# INDENT ONLY

L

P

BA


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-48

SCANIA

SERIES U.J. PART No. U.J. BRACKETS SLIP PART No. STUB PART No. SLIP ASSEMBLY TUBE SIZE WELD YOKE STYLE PART No. PART No. A B C B/C D E P40 K5-A599 TAPERED SC-3-61 SC-42-61 100 x 5 SC-26-61

P50 K5-A601 TAPERED SC-84-71 102 x 6 SC-26-71

P300 K5-A645 TAPERED SC-83-300# 90 x 5 SC-26-300#

P400 K5-A599 TAPERED SC-83-400 100 x 5 SC-26-400

P500 K5-A601 TAPERED SC-83-500 108 x 5.5 SC-26-500#

T60 K5-A596 NIL SC-3-60 SC-42-60 90 x 5 SC-26-60

T61 K5-A598 STRAIGHT SC-3-61 SC-42-61 100 x 5 SC-26-61

T70 K5-A597 NIL SC-3-70 NLA SC-42-70 NLA SC-84-70 95 x 5 SC-26-70

T71 K5-A600 STRAIGHT SC-84-71 102 X 6 SC-26-71

P600 K5-A756 TAPERED SC-83-600 114.3 x 5.5 SC-26-600

SCANIA TUBULAR TYPE ASSEMBLY

A B C D E

WELD YOKE CAP DIA. DISTANCE ACROSS C/LINE TO POINT TUBE O.D. SIZE SERIES PART No. YOKE EARS OF WELD P A L O

SC-26-60 44.0 159.0 75.0 90X5MM T60 1.732 6.260 2.953 90.00 x 5.00

SC-26-61 48.0 170.0 70.0 100X5MM T61 / P40 1.890 6.693 2.756 100.00 x 5.00

SC-26-70 50.0 177.0 86.0 T70 1.969 6.969 3.386 95.00 x 5.00

SC-26-71 57.0 175.0 75.0 T71 / P50 2.244 6.890 2.953 102.00 x 6.00

SC-26-300 38.0 170.0 65.0 90X5MM P300 1.496 6.693 2.559 90.00 x 5.00

SC-26-400 48.0 170.0 75.0 100X5MM P400 1.890 7.693 2.953 100.00 x 5.00

SC-26-420 48.0 170.0 95.0 P420(WideAngle) 1.890 7.693 3.740 95.00 x 5.00 Interaxle W/Yoke

SC-26-500 57.0 175.0 110.0 P500 2.244 6.890 4.331 108.00 x 5.50

SC-26-520 57.0 175.0 92.0 P520 2.244 6.890 3.622 92.00 x 5.00 WideAngle

SC-26-600 65.0 190.0 100.0 P600 2.559 7.480 3.937 114.30 x 5.50

SCANIA WELD YOKE

A

P


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-49

SCANIA

SERIES MIDSHIP STUB SPLINE TUBE MIDSHIP CENTRE BEARING END YOKE SHAFT DIA. & No. SIZE STUB NUT BEARING I.D. PART No. PART No. PART No. ASSEMBLY PART No. A B E C D

P300 SC-57-300# 59.75 x 24 spline 90 x 5 SC-94-373 SC-47-985-1X 60.0 SC-4-300# 44 x 1.5mm or SC-30-9108 2.362

P400 SC-57-400# 59.75 x 24 spline 100 x 5 SC-94-373 SC-47-985-1X 60.0 SC-4-400# 44 x 1.5mm or SC-30-9108 2.362

P500 SC-57-500# 59.75 x 24 spline 108 x 5.5 SC-94-373 SC-47-985-1X 60.0 SC-4-500# 44 x 1.5mm or SC-30-9108 2.362

P600 SC-57-600# 59.75 x 24 spline 114.3 x 5.5 SC-94-373 SC-47-985-1X 60.0 SC-4-600# 44 x 1.5mm or SC-30-9108 2.362

T61 / P40 SC-57-6171 54.8 x 22 spline 102 x 6 SC-74-788 # 80mm SEAL 60.0 SC-4-61 50 x 1.5mm 2.362

SCANIA CENTRE BEARING ASSEMBLYAB

C D

E

SERIES MIDSHIP SPLINE TUBE MIDSHIP CENTRE BEARING END YOKE ASSEMBLY DIA. & No. SIZE STUB NUT BEARING I.D. / FLANGE PART No. PART No. PART No. PART No. A B E C D

P400 SC-56-400 59.75 x 24 spline 100 x 5 SC-94-373 SC-47-985-1X 60.0 SC-4-400# 44 x 1.5mm or SC-30-9108 2.362

P500 SC-56-500 59.75 x 24 spline 108 x 5.5 SC-94-373 SC-47-985-1X 60.0 SC-4-500# 44 x 1.5mm or SC-30-9108 2.362

P600 SC-56-600 59.75 x 24 spline 114.3 x 5.5 SC-94-373 SC-47-985-1X 60.0 SC-4-600# 44 x 1.5mm or SC-30-9108 2.362

P600 SC-56-600-KV 59.75 x 24 spline 114.3 x 5.5 SC-94-373 SC-30-9108 60.0 KV FLANGE 44 x 1.5mm 2.362 208MM

SCANIA MIDSHIP ASSEMBLY

AssembliescomecompletewithStub,EndYokeorFlangeandBearing.

# INDENT ONLY


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-50

T60, T70 SC-47-959-1X 55mm

SCANIA CENTRE BEARINGS Vehicle Model Hardy Spicer O.E.Part No. Year Bearing Bolt Hole Part No. ID Centres

Suits Scania truck

SC-47-985-1X 1113031 60mmSuits Scania truck85mm Seal

yoke side22mm wide

bearing

P300, P400 SC-30-9108 1387764 2006- 60mm P500 & P600

Suits Scania truck26mm wide

bearingService Free

SCANIA


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-51

K5-A649 20.07 59.80 1 NIL Staked Suzuki 0.790 2.354

RUJ-1795 25.00 42.90 2 CENTRE 0.984 1.689

RUJ-1801 25.00 42.90 NIL Suzuki to 1140 series 0.984 1.689 23.80 61.30 0.937 2.413

K5-A557 25.00 63.90 1 CAP 0.984 2.516

SUZUKI


FIGURE 1 FIGURE 2

C B1 CB1 B2

SUZUKI UNIVERSAL JOINT KIT


M S B1

L

C

FIGURE 1

SUZ-2-008 2 25.00 42.90 37.0 M-42.00 73.0 52 x 52 4 8.0 RUJ-1795 0.984 1.689 1.457 M-1.634 2.874 0.315

SUZ-2-009 1 25.00 63.90 41.0 M-45.00 79.0 56 x 56 4 8.0 K5-A557 0.984 2.516 1.614 M-1.772 3.110 0.315

SUZ-2-010 1 25.00 63.90 40.0 M-45.00 85.0 60 x 60 4 10.0 K5-A557 0.984 2.516 1.575 M-1.772 3.346 0.394 Vitara

SUZUKI FLANGE YOKE

FIGURE 2

C

SM

L

B2


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-52


C

B1

L

FIGURE 2

B2

FIGURE 1

SUZ-3-002 1 25.00 42.90 20.00-18 113.0 RUJ-1795 Transmission Yoke 0.984 1.689 0.787 4.449

SUZ-3-103 1 25.00 63.90 24.00-23 114.0 K5-A557 Transmission Yoke 0.984 2.516 0.945 4.488

SUZ-3-102* 2 25.00 42.90 25.00-13 134.0 SUZ-42-009 RUJ-1795 SUZ-RB-101 - Boot 0.984 1.689 0.984 5.276 Metal Dust Cover Included

SUZ-3-104* 2 25.00 63.90 27.00-16 135.0 SUZ-42-100 K5-A557 SUZ-RB-102 - Boot 0.984 2.516 1.063 5.315 Metal Dust Cover Included

SUZUKI SLIP YOKE

B

STUB PART No. SPLINE DIA. & No. FIGURE LENGTH OF END OF SPLINE TUBE O.D. & SPLINE TO POINT OF THICKNESS WELD B G L

SUZ-42-100 27.00-16 1 90.0 117.0 50X2MM 1.063 3.543 4.606 *Can use 1613-0000

SUZ-42-009# 25.00-13 2 90.0 427.0 Suits bored weld yoke 0.984 3.543 16.811 SUZ-28-009 20mm

SUZ-42-102 25.00-13 1 130.00 50X2MM 0.984 5.118

SUZUKI STUB

L

C

B B1B2

G

L

FIGURE 1

B B

FIGURE 2

G

L

G

* Metal dust cover only included, rubber boot not included, purchase separately if required.

# INDENT ONLY


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-53

SUZUKI

B1 T

C

FIGURE 1

B2 T

C

FIGURE 2

WELD YOKE FIG. U.J. DIMENSIONS C/LINE TO TUBE O.D. BUTT TYPE U.J. PART No. POINT OF & WALL PART No. WELD THICKNESS C B1 B2 L T

SUZ-28-009# 2 25.00 42.90 47.0 20mm Bore RUJ-1795 0.984 1.689 1.850 Hollow

SUZ-28-008* 1 25.00 63.90 42.90 40.0 50X2MM 46mm Butt K5-A557 0.984 2.516 1.689 1.574 50.00 x 2.00 RUJ-1795

SUZUKI WELD YOKE

L L

* Yoke ears are machined to suit both U/Joints

# INDENT ONLY


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-54


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-55

K5-A519 28.57 77.90 1 CAP OLDER L/CRUISER, DYNA, COASTER 1.12 3.07

114-2501 28.58 54.00 2 SIDE FRONT SHAFT DOUBLE CARDAN CV 1.13 2.13

RUJ-2016 26.00 55.96 1 NIL 2WD HILUX 1.02 2.20

RUJ-2100 29.00 52.00 2 CAP 4WD HILUX, 4 RUNNER 1.14 2.05

RUJ-2100HD 29.00 52.00 2 CAP HI-PERFORMANCE THRUST WASHER 1.14 2.05 4WD HILUX, 4 RUNNER

RUJ-2109 29.00 52.00 2 CENTRE 4WD HILUX, 4 RUNNER 1.14 2.05

RUJ-2109HD 29.00 52.00 2 CENTRE HI-PERFORMANCE THRUST WASHER 1.14 2.05 4WD HILUX, 4 RUNNER

RUJ-2041 32.00 64.0 2 SIDE STANDARD L/CRUISER, DYNA, COASTER 1.26 2.51

RUJ-2041HD-1X 32.00 64.0 2 CAP HI-PERFORMANCE THRUST WASHER 1.26 2.51 L/CRUISER, DYNA,COASTER

RUJ-2041HD 32.00 64.0 2 SIDE HI-PERFORMANCE THRUST WASHER 1.26 2.51 L/CRUISER, DYNA, COASTER SUPPLIED WITH TWO SETS CIRCLIPS

PART No. C B1 B2 FIG LUBE DESCRIPTION

TOYOTA UNIVERSAL JOINT KIT

TOYOTA

FIGURE 1 FIGURE 2

B1C B1 B2C


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-56

FLANGE FIG. FLANGE DIA. C/L OF U.J. SPIGOT DIA P.C.D. BOLT HOLE No. HOLE DIA. U.J. PART YOKE TO FACE M = MALE PATTERN HOLES No. PART No. S L F E

TH-2-A1299 2 101.5 35.7 M-46.0 85.0 56 x 64 4 8.3 RUJ-2100 3.996 1.406 M-1.81 3.346 2.20 x 2.52 0.327

TH-2-A2209 2 113.5 45.5 M-46.0 84.6 60 x 60 4 10.2 RUJ-2100 4.469 1.791 M-1.81 3.331 2.36 x 2.36 0.402

4WD HILUX, 4 RUNNER

TL-2-A1149* 1 105.0 40.4 M-46.0 85.0 56 x 64 4 10.3 K5-A519 4.134 1.591 M-1.81 3.346 2.20 x 2.52 0.406 * DISCONTINUED - USE HILUX PARTS (TH-2-A1299)

TL-2-A1139 2 111.0 43.0 M-46.0 91.1 60 x 68 4 11.5 RUJ-2041 4.370 1.693 M-1.81 3.587 2.36 x 2.68 0.453

TL-2-A2049 2 115.0 43.0 M-46.0 93.0 66 x 66 4 11.5 RUJ-2041 4.528 1.693 M-1.81 3.661 2.60 x 2.60 0.453

TL-2-A2700 2 115.0 45.0 M-46.0 93.0 66 x 66 4 11.5 RUJ-2109 4.528 1.693 M-1.81 3.661 2.60 x 2.60 0.453

LANDCRUISER, DYNA, COASTER

FIGURE 1 FIGURE 2

TOYOTA FLANGE YOKE

TOYOTA


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-57

TOYOTA

SLIP YOKE BOOT LENGTH INTERNAL DIA. MINOR DIA. SLIP PART No CONVOLUTION KIT PART No. No. A B C

TL-408-10 195.0 63.5 39.0 TH-3-A3631 4

7.677 2.500 1.535

4WD HILUX, 4 RUNNER

LANDCRUISER, DYNA, COASTER TL-408-10 195.0 63.5 39.0 TL-3-A3581 4 7.677 2.500 1.535

BOOT KIT CAN ONLY BE USED ON HARDY SPICER HIGH PERFORMANCE SLIP / STUB

TOYOTA SLIP YOKE BOOT KIT

C

A

B


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-58

TOYOTA

SLIP YOKE FIG. SPLINE C/LINE TO LENGTH OF SLIP O.D. STUB U.J. COMMENTS PART No. OD & No. END OF HOLE PART No. PART No. SPLINE B L G A

TH-3-A3481 2 33.50-20 193.0 147.0 40.0 TH-42-A1701 RUJ-2100 STANDARD 1.318 7.60 5.79 1.57 65X1-6MM

TH-3-A3631 3 38.10-16 204.0 159.0 K3-42-A3631 RUJ-2100 HIGH PERFORMANCE 1.500 8.03 6.26 65X1-6MM

TH-3-A3631 3 38.10-16 204.0 159.0 K3-42-A1151 RUJ-2100 HIGH PERFORMANCE 1.500 8.03 6.26 3x.095

K3-42-A1151 butt has to be machined to suit tube.

4WD HILUX, 4 RUNNER

TL-3-A3361# 1 33.50-20 149.5 114.5 40.0 TL-42-A1591 K5-A519 STANDARD 1.318 5.89 4.51 1.57 65X1-6MM 1964 TO Jan. 1974 # SUPERCEDED TO TH-42-A1701, TH-3-A3481 & TH-2-A1299

TL-3-A3351# 2 33.50-20 152.2 112.0 40.0 TL-42-A1591 RUJ-2041 STANDARD 1.318 5.99 4.41 1.57 65X1-6MM Jan. 1974- # SUPERCEDED TO TL-42-60020 & TL-3-36020

TL-3-36020 2 33.50-20 152.2 112.0 42.0 TL-42-60020 RUJ-2041 STANDARD 1.318 5.99 4.41 1.65 65X1-6MM Jan. 1974-

TL-3-A3581 3 38.10-16 187.0 159.0 K3-42-A3631 RUJ-2041 HIGH PERFORMANCE 1.500 7.36 6.26 65X1-6MM SLIP Jan. 1974-

TL-3-A3581 3 38.10-16 187.0 159.0 K3-42-A1151 RUJ-2041 HIGH PERFORMANCE 1.500 7.36 6.26 3x.095 SLIP Jan. 1974-

TL-3-A0050 2 33.50-20 184.5 148.0 40.0 TL-42-A232 RUJ-2041 1.318 7.26 5.83 1.57 65X1-6MM

K3-42-A1151 butt has to be machined to suit tube.


TOYOTA SLIP YOKE

FIGURE 1 FIGURE 2

FIGURE 3

A A


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-59

TL-42-A1591# 1 33.10-20 STEEL 34.1 90.0 155.0 65X1-6MM TL-3-A3361 1.318 1.343 3.543 6.102 65.00 x 1.60 EARLY MODEL # SUPERCEDED TO TH-42-A1701, TH-3-A3481 & TH-2-A1299

TL-42-A1591# 1 33.10-20 STEEL 34.1 90.0 155.0 65X1-6MM TL-3-A3351 1.318 1.343 3.543 6.102 65.00 x 1.60 # SUPERCEDED TO TL-42-60020 & TL-3-36020

K3-42-A3631 2 38.10-16 HARDY N/A 75.0 197.0 H 65X1-6MM TL-3-A3581 1.500 COATED 2.953 7.756 65.00 x 1.60

K3-42-A1151* 2 38.10-16 HARDY N/A 65.0 187.0 H 2413-0000 TL-3-A3581 1.500 COATED 2.559 7.362 3.00 x .095

TL-42-A232 1 33.10-20 STEEL 34.1 86.0 235.0 65X1-6MM TL-3-A0050 1.318 1.343 3.386 9.252 65.00 x 1.60

TL-42-60020 1 33.10-20 STEEL 42.8 90.0 155.0 65X1-6MM TL-3-36020 1.318 1.685 3.386 6.102 65.00 x 1.60

*Buttmaybemodifiedtosuit2.50x.095PartNo.2013-000

TOYOTA

STUB FIG. SPLINE SPLINE SHOULDER LENGTH END OF BUTT TUBE SLIP YOKE PART No. DIA. & No. TYPE DIAMETER OF SPLINE SPLINE TO TYPE O.D. & PART No. POINT OF THICKNESS WELD D H1 G L M

TH-42-A1701 1 33.10-20 STEEL 43.0 86.0 195.0 65X1-6MM TH-3-A3481 1.318 1.693 3.386 7.677 65.00 x 1.60

K3-42-A3631 2 38.10-16 HARDY N/A 75.0 197.0 H 65X1-6MM TH-3-A3631 1.500 COATED 2.953 7.756 65.00 x 1.60

K3-42-A1151* 2 38.10-16 HARDY N/A 65.0 187.0 H 2413-0000 TH-3-A3631 1.500 COATED 2.559 7.362 76.20 x 2.41

BUTT TYPE H = HOLLOW S= SOLID *Buttmaybemodifiedtosuit2.50x.095PartNo.2013-000

4WD HILUX, 4 RUNNER


FIGURE 1 FIGURE 2

TOYOTA STUB

MM


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-60

DUST COVER FIG. LENGTH COVER SLEEVE STUB PART No. COMMENTS PART No. INSIDE DIAMETER L M

TH-86-A128 2 131.5 42.6 TH-42-A1701 STD

5.177 1.677

4WD HILUX, 4 RUNNER

TOYOTA

FIGURE 1 FIGURE 2

TL-86-A108 1 93.5 34.0 TL-42-A1591 LANDCRUISER/ 3.681 1.339 No Longer Available DYNA

TL-86-A0010 1 158.5 34.0 TL-42-A232 LONG 6.240 1.339

TL-86-26020 1 93.5 42.6 TL-42-60020 LANDCRUISER 3.681 1.677


WELD YOKE FIG. C/LINE TO POINT TUBE O.D. & WALL BUTT TYPE U.J. PART No. PART No. OF WELD THICKNESS L F

TH-26-A2397 2 43.0 65X1-6MM H RUJ-2100 1.693 65.00 x 1.60

Buttmaybemodifiedtosuit2.50x095PartNo.2013-000

4WD HILUX, 4 RUNNER

TL-26-A2067 1 50.0 65X1-6MM H K5-A519 1.969 65.00 x 1.60

TL-26-A2077 2 48.4 65X1-6MM H RUJ-2041 1.904 65.00 x 1.60

TL-26-A3095 2 50.0 2413-0000 S RUJ-2041 1.969 3.000 x .095

Buttmaybemodifiedtosuit2.50x095PartNo.2013-000


FIGURE 1 FIGURE 2

TOYOTA DUST COVER

TOYOTA WELD YOKE

F


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-61

TOYOTA

FLANGE YOKE PART No. U.J. SLIP YOKE DUST COVER STUB MALE TUBE SIZE WELD YOKE PART No. FEMALE PART No. PART No. PART No. PART No. A B C D E F G

TH-2-A1299 or TH-2-A2209 RUJ-2100 TH-3-A3481 TH-86-A128 TH-42-A1701 65X1-6MM TH-26-A2397 65.00 x 1.60

TH-2-A1299 or TH-2-A2209 RUJ-2100 TH-3-A3631 INCLUDED K3-42-A3631 65X1-6MM TH-26-A2397 WITH SLIP 65.00 x 1.60

TH-2-A1299 or TH-2-A2209 RUJ-2100 TH-3-A3631 INCLUDED K3-42-A1151* 65X1-6MM TH-26-A2397 WITH SLIP 65.00 x 1.60

*Buttsuits3x.095tubePartNo.2413-0000butcanbemodifiedtosuit2.50x.095PartNo.2013-000

4WD HILUX, 4 RUNNER

TOYOTA TUBULAR TYPE ASSEMBLY

TL-2-A1149 K5-A519 TL-A3361 TL-86-A108 TL-42-A1591 65X1-6MM TL-26-A2067 65.00 x 1.60

TL-2-A1139 or TL-2-A2049 RUJ-2041 TL-3-A3351 TL-86-A108 TL-42-A1591 65X1-6MM TL-26-A2077 65.00 x 1.60

TL-2-A1139 or TL-2-A2049 RUJ-2041 TL-3-A3581 INCLUDED K3-42-A3631 65X1-6MM TL-26-A2077 WITH SLIP 65.00 x 1.60

TL-2-A1139 or TL-2-A2049 RUJ-2041 TL-3-A3581 INCLUDED K3-42-A1151* 65X1-6MM TL-26-A2077 WITH SLIP 65.00 x 1.60

TL-2-A1139 or TL-2-A2049 RUJ-2041 TL-3-A0050 TL-86-A0010 TL-42-A232 65X1-6MM TL-26-A2077 65.00 x 1.60

*Buttsuits3x.095tubePartNo.2413-0000butcanbemodifiedtosuit2.50x.095PartNo.2013-000


A B G F E

C B AD


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-62

5 CV-163 13.0 37.0 0.512 1.457 5 SCV-34 12.0 34.0 0.472 1.339

OVERSIZE BALL KIT SEAL PART No. BALL KIT O.D. K FIG. 6 TL-409-4 38.6 1.520 ReplacesstandardsealsuppliedwithSCV-34tofitoversizedhousingyoke.

ADAPTOR RING PART No. FIG. 7 TL-407-16 AllowssealinSCV-34tofit AllowsstandardsealsuppliedwithSCV-34tofitoversizedhousingyoke.

VEHICLE ASSEMBLY BOLT HOLE BOLT SPIGOT P.C.D. TUBE PIN BALL FLANGE U.J. TO U.J. TO PART No. PATTERN HOLE DIA. O.D. & O.D. KIT TO U.J. WELD DIA. M = MALE THICKNESS O.D. C/L U.J. B1 X B2 F E M H K L1 L2 L3 LANDCRUISER 800-R2510 60 x 68 11.0 M-46.0 91.1 65X1-6MM 13.0 37.0 38.0 78.0 49.0 2.36 x 2.68 0.433 M-1.81 3.587 65.00 x 1.60 0.512 1.457 1.496 3.071 1.929 HILUX 800-R2520 60 x 68 8.2 M-46.0 91.1 65X1-6MM 13.0 37.0 38.0 78.0 49.0 2.36 x 2.68 0.323 M-1.81 3.587 65.00 x 1.60 0.512 1.457 1.496 3.071 1.929 HILUX 800-R2530 60 x 68 10.0 M-46.0 91.1 65X1-6MM 13.0 37.0 38.0 78.0 49.0 2.36 x 2.68 0.394 M-1.81 3.587 65.00 x 1.60 0.512 1.457 1.496 3.071 1.929 HILUX 800-R2550 61.4 x 70 10.0 M-46.0 93.18 65X1-6MM 13.0 37.0 38.0 78.0 49.0 DIESEL 97- 2.42 x 2.76 0.394 M-1.81 3.668 65.00 x 1.60 0.512 1.457 1.496 3.071 1.929 PRADO 800-R2560 60 x 60 10.0 M-46.0 84.5 65X1-6MM 13.0 37.0 38.0 78.0 49.0 REAR 2.36 x 2.36 0.394 M-1.81 3.327 65.00 x 1.60 0.512 1.457 1.496 3.071 1.929 Buttmaybemodifiedtosuit2.50x.095PartNo.2013-000

TOYOTA

Complete assemblyFIGURE 1

Pin Yoke with Dust CoverFIGURE 2

FIG. PART No. PIN O.D. BALL KIT O.D. H K

Ball Kit AssemblyFIGURE 5

TOYOTA DOUBLE CARDAN CV JOINT

TOYOTA BALL KIT ASSEMBLIES

OversizeBall Kit sealFIGURE 6

AdaptorRingFIGURE 7

Universal Joint

Centre YokeFIGURE 3

Cardan Weld YokeFIGURE 4

L1B1

B2

L2 L3

FIG. DESCRIPTION L/CRUISERPART No.

HILUXPART No.

HILUXPART No.

HILUXPART No.

HILUXDIESEL 97-

PRADOREAR

1 COMPLETE ASSY 800-R2510 800-R2520 800-R2530 800-R2550 800-R25602 PIN YOKE WITH DUST COVER 25R-24-9048 25R-24-9058 25R-24-9068 25R-24-9078# 25R-24-9088 N.S.S.

UNIVERSAL JOINT 114-2501 114-2501 114-2501 114-2501 114-2501 114-2501

3 CENTRE YOKE 25R-29-511 25R-29-511 25R-29-511 25R-29-511 25R-29-511

4 CARDAN WELD YOKE 25R-25-1140 25R-25-1140 25R-25-1140 25R-25-1140 25R-25-1140

5 BALL KIT ASSEMBLY CV-163 CV-163 CV-163 SCV-34 CV-163 CV-163

# Bolt pattern is 60 x 60 with 8.2mm holes. Pin is 12mm diameter.


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-63

TOYOTA

TOYOTA CENTRE BEARING ASSEMBLY

^NowMultifitwith12Holes

Assembliesonlyincludemidshipstub,washer,nut&companionflange.

Available separately 94-A767 - Lock Nut, 94-A768 - Washer to suit above. Selectcentrebearingfromcentrebearingsection.Flangedrilledtosuit

other Toyota bolt patterns.

CB

A D

MIDSHIP ASSEMBLY PART No.

SPLINEDIA. &No.

D

COMPANION FLANGE TOPOINT OF

WELD

BEARINGI.D.

A

BOLTHOLE

PATTERN

BUTTDIA.

B

P.C.D. FLANGEDIA.

C

SPIGOTDIA.

F=FEMALE

C/L OFC/BEARING

TO BOLTCENTRE

HILUXTH-53-A6060 28.00-27 30.00 60 x 60 x 10 62.00 84.60 115.00 F-46.00

1.102 1.181 2.36 x 2.36 2.441 3.331 4.528 M-1.81

DYNATL-53-A1900 ^ 28.00-27 125.00 30.00 66 x 66 x 11 62.00 93.00 115.00 F-46.00 20.00

1.102 4.921 1.181 2.60 x 2.60 2.441 3.661 4.528 M-181 0.787

60 x 60 x 11

2.36 x 2.36

60 x 60 x 10

2.36 x 2.36

TOYOTA COMPANION FLANGE

C

B2

B1

COMPANION FLANGE

PART NO.

SPLINE DIA. & NO.

BOLT HOLE PATTERN B1 & B2

P.C.D. FLANGE DIA.

C

SPIGOT DIA. F=FEMALE

COMMENTS

TL-1-35040 28.0 x 27 SPL 60 x 60 84.6 105.0 F-46.0 SUIT HZJ75 SERIES1.102 2.36 x 2.36 3.331 4.134 F-1.811 FRONT DIFF

TL-1-60030 28.0 x 27 SPL 66 x 66 93.0 115.0 F-46.0 SUIT HJ & HZJ SERIES1.102 2.60 x 2.60 3.861 4.528 F-1.811 REAR DIFF

TL-1-35082 30.2 x 29 SPL 60 x 60 84.6 103.0 F-46.0 SUIT HZJ78, 79 SERIES1.189 2.36 x 2.36 3.331 4.055 F-1.811 FRONT DIFF LATE


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-64

TOYOTA


TOYOTA CENTRE BEARINGS

Celica 17R-30-2110 37230-14031 11/77-10/81 30mm 151mm Corona 37230-14031 10/79-7/83 30mm

RA40XT130

Sedan & Wagon

RA60ST141Sedan&Wagon

MX73. GX71MA61 2 door liftback

Corolla 17R-30-2310 37230-12040 79-87 163mm Sprinter 2WD 37230-12040 79-83

TE 70E. 71E. CE 70E. KE70TE70. CE70F

Corolla 17R-30-6130 37230-12081 84-87 30mm 151mm

AE95 FR 3PC

AL25 4WD

Celica 17R-30-2710 37230-24010 11/81-9/83 30mm 150mm Corona 37230-24010 8/83-11/84 30mm Cressida 37230-24020 84-88 30mm Supra 2WD 37230-24010 10/83-85 30mm Tercel 37230-24020 82-88 30mm

TOYOTA COMPLETE SHAFTSPART No. FIG APPLICATION SHAFT

LOCATIONOEM

PART No.COMMENTS

37140-35030 1 HILUX 8/83~7/98 FRONT 37140-35030 INCLUDES DOUBLE CARDAN

HZJ78-6A250 3 HZJ78 LANDCRUISER 8/99 ON REAR 37110-6A250

HZJ79-35190 2 HZJ79 LANDCRUISER 8/99 ON FRONT 37140-35190

HZJ79-6A260 3 HZJ79 LANDCRUISER 8/99 ON REAR 37110-6A260

FIG 1.

FIG 3.

FIG 2.


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-65

TOYOTA

Corona 17R-30-2410 37230-20090 10/79-82

RT132 133Lift backs

Toyota cont. Vehicle Model Hardy Spicer O.E.Part No. Year Bearing Bolt Hole Part No. ID Centres

Corolla 17R-30-6140 37230-12091 84-87 30mm 148mm

AE95 (REAR) 3PC

Cressida 17R-30-6110 37230-22042 82-84 30mm 165mm

GX60

Cressida 17R-30-6120 37230-22110 89-93 30mm 150mm

MX83

Crown 17R-30-6080 37230-30022 74-79 30mm 112mm

Crown 17R-30-6090 37230-30030 79-83 30mm 120mm

MS112

Crown 17R-30-6100 37230-30050 -91 30mm 140mm

MS122, 3, 5

Dyna TD-30-A3010 37230-36060 81-88 30mm 125mm

Coaster

RU30, BU30,BU45 RU20, BB20,HB30, BU80,BU90, YU80,WU90

Coaster TD-30-6270 37230-36140 93- 30mm 125mm 93-

80mmCentreHeight


Document No:

Issue:

Issue Date:

HSDSCAT

10/07/13



6

B:5-66


CENTRE BEARINGS Cont.

Hilux 2WD TH-30-5410 37230-40031 75-78 30mm 109mm

Hilux 2WD TH-30-5510 37230-35030 79-82 30mm 150mm

RN25, LN25

LN40, 41. RN40

(uses 8mm bolts)

Hilux 2WD TH-30-A3210 37230-35050 8/83-7/88 30mm 150mm Hilux 2WD 37230-35070 8/88 30mm 150mm

YN55, 56, 57, 58. LN55, 56 (uses 10mm bolts)

YN85. LN85

GGN15RTGN16RKUN16R

Hilux 2WD TH-30-6800 37230-0K021 3/05- 30mm 152mm

Hilux 2WD TH-30-4710 37230-35090 90- 30mm 155mm

YN85 LN85

Hilux 2WD TH-30-5750 37230-35120 97-2/05 30mm 148mm

TOYOTA

Commuter TH-30-5800 37230-26010 89- 30mm 150mm Hiace

LH/RZH 125

Hilux TH-30-5760 69-75 30mm 80mm

RN15Stout

Hiace TH-30-7000 37230-26020 95-03 30mm 148mm Spacia 11/96-04 Town-Ace 11/96-04 Lite-Ace 11/96-04

RCH12SR40CR4#KR4#


Document No:

Issue:

Issue Date:

HSDSCAT

6

10/07/13



B:5-67

Hilux 4WD TH-30-6810 37230-0K020 3/05- 30mm 152mm

KUN26RGGN25R

Hilux 4WD TH-30-5770 37230-35130 97-2/05 30mm 148mm

TOYOTA Toyota cont.

Vehicle Model Har

B5 4WD-Truck & Forklift 2013-6lr

Documents

Transcript of B5 4WD-Truck & Forklift 2013-6lr