AVT Oscar · 2010. 3. 8. · 2.2.0 26.10.2006 Added Format_7 binning modes for Oscar F-510C...
Transcript of AVT Oscar · 2010. 3. 8. · 2.2.0 26.10.2006 Added Format_7 binning modes for Oscar F-510C...
Technical Manual
V2.4.0
15 August 2008
Allied Vision Technologies GmbHTaschenweg 2aD-07646 Stadtroda / Germany
AVT Oscar
OSCAR Technical Manual V2.4.0
2
Legal noticeFor customers in the U.S.A.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential envi-ronment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However there is no guarantee that interferences will not occur in a particular installation. If the equipment does cause harmful interference to radio or televi-sion reception, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.• Increase the distance between the equipment and the receiver.• Use a different line outlet for the receiver.• Consult a radio or TV technician for help.
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. The shielded interface cable recom-mended in this manual must be used with this equipment in order to comply with the limits for a computing device pursuant to Subpart B of Part 15 of FCC Rules.
For customers in CanadaThis apparatus complies with the Class B limits for radio noise emissions set out in the Radio Interference Regulations.
Pour utilisateurs au CanadaCet appareil est conforme aux normes classe B pour bruits radioélectriques, spécifiées dans le Règlement sur le brouillage radioélectrique.
Life support applicationsThese products are not designed for use in life support appliances, devices, or systems where malfunction of these products can reasonably be expected to result in personal injury. Allied customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Allied for any damages resulting from such improper use or sale.
TrademarksUnless stated otherwise, all trademarks appearing in this document of Allied Vision Technologies are brands protected by law.
WarrantyThe information provided by Allied Vision Technologies is supplied without any guarantees or warranty whatsoever, be it specific or implicit. Also excluded are all implicit warranties con-cerning the negotiability, the suitability for specific applications or the non-breaking of laws and patents. Even if we assume that the information supplied to us is accurate, errors and inaccuracy may still occur.
CopyrightAll texts, pictures and graphics are protected by copyright and other laws protecting intellec-tual property. It is not permitted to copy or modify them for trade use or transfer, nor may they be used on web sites.
Allied Vision Technologies GmbH 08/2008All rights reserved.Managing Director: Mr. Frank GrubeTax ID: DE 184383113
Support:
Taschenweg 2AD-07646 Stadtroda, GermanyTel.: +49 (0)36428 6770Fax: +49 (0)36428 677-28e-mail: [email protected]
OSCAR Technical Manual V2.4.0
3
Contents
Contacting Allied Vision Technologies ................................................... 8
Introduction ............................................................................................................ 9Document history .......................................................................................................... 9Manual overview........................................................................................................... 13Conventions used in this manual..................................................................................... 14
Styles ..................................................................................................................... 14Symbols .................................................................................................................. 14
More information.......................................................................................................... 15Before operation .......................................................................................................... 15
OSCAR cameras ..................................................................................................17
Declarations of conformity ...........................................................................18
Filter and lenses .................................................................................................19IR cut filter: spectral transmission .................................................................................. 19Camera lenses .............................................................................................................. 20
Specifications .......................................................................................................21Oscar F-320C................................................................................................................ 21Oscar F-510C................................................................................................................ 23Oscar F-810C................................................................................................................ 25Spectral sensitivity ....................................................................................................... 27
Camera dimensions ..........................................................................................29Oscar standard housing ................................................................................................. 29Oscar W90 ................................................................................................................... 30Oscar W270.................................................................................................................. 31Tripod adapter ............................................................................................................. 32Cross section: C-Mount (standard filter) ........................................................................... 33Adjustment of C-Mount.................................................................................................. 34
Camera interfaces .............................................................................................35IEEE 1394a port pin assignment...................................................................................... 35Camera I/O pin assignment ............................................................................................ 36Status LEDs.................................................................................................................. 37
On LED ................................................................................................................... 37Status LED (yellow) .................................................................................................. 37
Control and video data signals........................................................................................ 39Inputs .................................................................................................................... 39
Triggers.............................................................................................................. 39Input/output pin control........................................................................................... 40
OSCAR Technical Manual V2.4.0
4
IO_INP_CTRL 1-2 ............................................................................................... 41Trigger delay ....................................................................................................... 42
Outputs .................................................................................................................. 44IO_OUTP_CTRL 1-2............................................................................................. 46Output modes...................................................................................................... 47
Pixel data.................................................................................................................... 49
Description of the data path........................................................................52Block diagram of the cameras......................................................................................... 52Black and white output interpolation modes..................................................................... 53Read out modes of the sensor......................................................................................... 53
Oscar F-320C: ICX-262AQ readout scheme ................................................................ 54Oscar F-510C: ICX-282AQ readout scheme ................................................................ 55Oscar F-810C: ICX-456AQ readout scheme ................................................................ 56Frame readout implications ................................................................................... 57
White balance .............................................................................................................. 59One-push automatic white balance ............................................................................. 61Automatic white balance ........................................................................................... 63
Manual gain................................................................................................................. 64Auto gain .................................................................................................................... 65Brightness (black level or offset) .................................................................................... 67Auto shutter ................................................................................................................ 69Look-up table (LUT) and gamma function......................................................................... 71
Loading an LUT into the camera ................................................................................. 73Shading correction........................................................................................................ 74
Automatic generation of correction data...................................................................... 75Requirements ...................................................................................................... 75Algorithm ........................................................................................................... 75
What is the real size of the shading image (MaxImageSize)?........................................... 79Loading a shading image out of the camera ................................................................. 81Loading a shading image into the camera .................................................................... 82
Horizontal mirror function ............................................................................................. 83Binning (only Oscar F-510C)........................................................................................... 84
2 x Binning ............................................................................................................. 84Vertical binning ....................................................................................................... 85Horizontal binning ................................................................................................... 862 x full binning........................................................................................................ 87
Sub-sampling ............................................................................................................... 88What is sub-sampling? .............................................................................................. 88Which Oscar models have sub-sampling? ...................................................................... 88Description of sub-sampling....................................................................................... 88High SNR mode (High Signal Noise Ratio) .................................................................... 89
Sharpness.................................................................................................................... 90Color interpolation........................................................................................................ 90
Color interpolation (BAYER demosaicing) ..................................................................... 91Color correction............................................................................................................ 92
Why color correction? ........................................................................................... 92
OSCAR Technical Manual V2.4.0
5
Color correction in AVT cameras ............................................................................. 92Color correction: formula....................................................................................... 92GretagMacbeth ColorChecker .................................................................................. 92
Color conversion (RGB YUV) ....................................................................................... 93Hue and Saturation....................................................................................................... 93Serial interface............................................................................................................. 95
Controlling image capture ..........................................................................100Trigger modi .............................................................................................................. 100
Edge mode (Trigger_Mode_0)................................................................................... 100Level mode (Trigger_Mode_1) .................................................................................. 101Bulk trigger (Trigger_Mode_15) ................................................................................ 102Trigger delay ......................................................................................................... 105
Trigger delay advanced register............................................................................ 106Shutter modes............................................................................................................ 108
Split shutter .......................................................................................................... 108Joint shutter ......................................................................................................... 110
Exposure time (shutter) and offset ................................................................................ 111Exposure time offset ............................................................................................... 111Example: Oscar F-510C ............................................................................................ 111Extended shutter.................................................................................................... 112
One-shot ................................................................................................................... 113One-shot command on the bus starting exposure ........................................................ 113End of exposure to first packet on the bus ................................................................. 114
Multi-shot ................................................................................................................. 115ISO_Enable / free-run.................................................................................................. 115Asynchronous broadcast .............................................................................................. 115Jitter at start of exposure ............................................................................................ 116Frame memory and deferred image transport................................................................... 117
HoldImg mode....................................................................................................... 118FastCapture ........................................................................................................... 119
Video formats, modes and bandwidth .................................................120Video formats: Oscar F-320C ......................................................................................... 121Video formats: Oscar F-510C ......................................................................................... 123Video formats: Oscar F-810C ......................................................................................... 127Area of interest (AOI) ................................................................................................. 129Frame rates................................................................................................................ 131
Frame rates Format_7 ............................................................................................. 135Oscar F-320C: AOI frame rates .................................................................................. 136
Oscar F-320C: progressive scan mode .................................................................... 136Oscar F-320C: interlaced mode ............................................................................. 137
Oscar F-510C: AOI frame rates .................................................................................. 138Oscar F-510C: progressive scan mode .................................................................... 138Oscar F-510C: interlaced modes............................................................................ 139
Oscar F-810C: AOI frame rates .................................................................................. 140Oscar F-810C: progressive scan mode .................................................................... 140Oscar F-810C: interlaced modes............................................................................ 141
OSCAR Technical Manual V2.4.0
6
How does bandwidth affect the frame rate? ...................................142Example formula for the Oscar F-810C camera......................................................... 143
Test images ............................................................................................................... 143Loading test images ............................................................................................... 143
Configuration of the camera......................................................................145Camera_Status_Register............................................................................................... 145
Example................................................................................................................ 146Configuration ROM...................................................................................................... 148Implemented registers (IIDC V1.3) ................................................................................ 151
Camera initialize register......................................................................................... 151Inquiry register for video format............................................................................... 151Inquiry register for video mode ................................................................................ 152Inquiry register for video frame rate and base address ................................................. 153Inquiry register for basic function............................................................................. 162Inquiry register for feature presence ......................................................................... 163Inquiry register for feature elements ......................................................................... 165Inquiry register for absolute value CSR offset address .................................................. 168Status and control register for one-push .................................................................... 169Feature control error status register .......................................................................... 173Video mode control and status registers for Format_7.................................................. 173
Quadlet offset Format_7 Mode_0 .......................................................................... 173Quadlet offset Format_7 Mode_1 .......................................................................... 173Format_7 control and status register (CSR) ............................................................ 173
Advanced features (AVT-specific) .................................................................................. 175Advanced registers summary .................................................................................... 175Version information register..................................................................................... 177Advanced feature inquiry......................................................................................... 181Maximum resolution ............................................................................................... 183Time base ............................................................................................................. 184Extended shutter.................................................................................................... 185Test images ........................................................................................................... 186Look-up tables (LUT) .............................................................................................. 187Shading correction ................................................................................................. 188Frame information.................................................................................................. 190Input/output pin control......................................................................................... 190Delayed Integration Enable (IntEna) ......................................................................... 191Auto shutter control ............................................................................................... 192Auto gain control ................................................................................................... 192Autofunction AOI ................................................................................................... 193Color correction ..................................................................................................... 195Trigger delay ......................................................................................................... 195Mirror image.......................................................................................................... 196Soft Reset ............................................................................................................. 196High SNR mode (High Signal Noise Ratio) .................................................................. 197User profiles .......................................................................................................... 198
Error codes ....................................................................................................... 199Reset of error codes ........................................................................................... 199
OSCAR Technical Manual V2.4.0
7
Stored settings .................................................................................................. 199GPDATA_BUFFER..................................................................................................... 201
Little endian vs. big endian byte order.................................................................. 201
Firmware update...............................................................................................202
Appendix ................................................................................................................203Sensor position accuracy of AVT cameras........................................................................ 203
Index.........................................................................................................................204
Contacting Allied Vision Technologies
OSCAR Technical Manual V2.4.0
8
Contacting Allied Vision Technologies
Info • Technical information:[email protected] (for Germany): +49 (0)36428 677-270phone (for USA): +1 978-225-2030outside Germany/USA: Please check the link for your local dealer.http://www.alliedvisiontec.com/partner.html
• Ordering and commercial information:[email protected] (for Germany): +49 (0)36428 677-230phone (for USA): +1 978-225-2030outside Germany/USA: Please check the link for your local dealer.http://www.alliedvisiontec.com/partner.htmlPlease note order number/text given in theAVT Modular Camera Concept.
Introduction
OSCAR Technical Manual V2.4.0
9
Introduction
This OSCAR Technical Manual describes in depth the technical specifica-tions, dimensions, all camera features (IIDC standard and AVT smart fea-tures) and their registers, trigger features, all video and color formats, band-width and frame rate calculation.
For information on hardware installation, safety warnings, pin assignments on I/O connectors and 1394a connectors read the Hardware Installation Guide.
Document history
Note Please read through this manual carefully.
We assume that you have read already the Hardware Installation Guide and that you have installed the hard-ware and software on your PC or laptop (FireWire card, cables).
Version Date Remarks
1.0 10.05.2005 First issue
1.1 25.08.2005 Oscar F-510C: firmware 1.05/3.00; minor corrections and clari-fications
2.0.0 14.03.2006 Manual compliant to firmware 3.03, added feature user profiles, minor corrections
2.0.1 15.03.2006 All Oscar cameras are Class B compliant.
2.1.0 28.06.2006 New layout, manual compliant to firmware 3.04, RoHS confor-mity, minor corrections
2.1.1 18.09.2006 Corrected BAYER demosaicing interpolation formula (Chapter Color interpolation (BAYER demosaicing) on page 91)
Minor corrections
2.2.0 26.10.2006 Added Format_7 binning modes for Oscar F-510C (Chapter Oscar F-510C on page 23, Chapter Binning (only Oscar F-510C) on page 84 and Chapter Video formats: Oscar F-510C on page 123)
Minor corrections
to be continued on next page
Table 1: Document history
Introduction
OSCAR Technical Manual V2.4.0
10
continued from last page
2.3.0 23.02.2007 Minor corrections
New offset and jitter values (Chapter Exposure time (shutter) and offset on page 111 and Figure 52: Data flow and timing after end of exposure on page 114)
New jitter values at start of exposure, camera idle (Chapter Jitter at start of exposure on page 116)
2.3.1 23.03.2007 Minor corrections
Note: binning only Oscar F-510C (Chapter Binning (only Oscar F-510C) on page 84)
2.4.0 15.08.08 Sensor tilting changed to rotation in Chapter Camera dimen-sions on page 29
Added detailed description of BRIGHTNESS (800h) in Table 78: Feature control error register on page 173
Added detailed description of WHITE-BALANCE (80Ch) in Table 78: Feature control error register on page 173 et seq.
Corrected exposure time example in Chapter Exposure time (shutter) and offset on page 111
Added Chapter Sensor position accuracy of AVT cameras on page 203
Moved AVT Glossary from Appendix of OSCAR Technical Manual to AVT Website.
Changed provisions directive to 2004/108/EG in Chapter Dec-larations of conformity on page 18
Added detailed level values of I/Os in Chapter Camera I/O pin assignment on page 36.
to be continued on next page
Version Date Remarks
Table 1: Document history
Introduction
OSCAR Technical Manual V2.4.0
11
continued from last page
2.4.0
[continued]
15.08.08
[continued]
Restructuring of Oscar Technical Manual:
• Added Contacting Allied Vision Technologies on page 8• Added Chapter Manual overview on page 13• Restructured Chapter Oscar types and highlights to Chapter
OSCAR cameras on page 17.– Infos from Oscar camera types table moved to Chapter
Specifications on page 21– Safety instructions moved to Hardware Installation
Guide, Chapter Safety instructions and AVT camera cleaning instructions
– Environmental conditions moved to Oscar Instruction Leaflet
– Infos on C-Mounting moved to Hardware Installation Guide, Chapter Changing filters safety instructions
– Infos on System components and Environmental condi-tions moved to Oscar Instruction Leaflet
– Infos on IR cut filter and Lenses moved to Chapter Fil-ter and lenses on page 19
• Moved binning explanation from Chapter Specifications on page 21 to Chapter Video formats, modes and band-width on page 120
• Binning / sub-sampling modes and color modes are only listed in Chapter Video formats, modes and bandwidth on page 120
• Moved detailed description of the camera interfaces (FireWire, I/O connector), ordering numbers and operat-ing instructions to the Hardware Installation Guide.
• Revised Chapter Description of the data path on page 52• Revised Chapter Controlling image capture on page 100;
added Table 30: Trigger modi on page 100; User profiles are only described in Chapter User profiles on page 198
• Revised Chapter Video formats, modes and bandwidth on page 120
to be continued on next page
Version Date Remarks
Table 1: Document history
Introduction
OSCAR Technical Manual V2.4.0
12
continued from last page
2.4.0
[continued]
15.08.08
[continued]
• Revised Chapter How does bandwidth affect the frame rate? on page 142
• Revised Chapter Configuration of the camera on page 145• Revised Chapter Firmware update on page 202• Added Chapter Sensor position accuracy of AVT cameras on
page 203• Revised Chapter Index on page 204
Added cross-reference from upload LUT to GPDATA_BUFFER in Chapter Loading an LUT into the camera on page 73.
Added cross-reference from upload/download shading image to GPDATA_BUFFER in:
– Chapter Loading a shading image out of the camera on page 81
– Chapter Loading a shading image into the camera on page 82
Added little endian vs. big endian byte order in Chapter GPDATA_BUFFER on page 201
Added RoHs in Chapter Declarations of conformity on page 18
Added descriptions of MaxImageSize in Chapter What is the real size of the shading image (MaxImageSize)? on page 79
Listed shutter speed with offset in Chapter Specifications on page 21ff.
New measurement of IntEna signals, therefore new offsets in Chapter Exposure time (shutter) and offset on page 111 and in Figure 52: Data flow and timing after end of exposure on page 114.
New photo of LED positions in Figure 13: Position of Status LEDs on page 37
Version Date Remarks
Table 1: Document history
Introduction
OSCAR Technical Manual V2.4.0
13
Manual overview
This manual overview describes each chapter of this manual shortly.• Chapter Contacting Allied Vision Technologies on page 10 lists AVT con-
tact data for both:– technical information / ordering– commercial information
• Chapter Introduction on page 9 (this chapter) gives you the document history, a manual overview and conventions used in this manual (styles and symbols). Furthermore you learn how to get more information on how to install hardware (Hardware Installation Guide), available AVT software (incl. documentation) and where to get it.
• Chapter OSCAR cameras on page 17 gives you a short introduction to the STINGRAY cameras with their FireWire technology. Links are provided to data sheets and brochures on AVT website.
• Chapter Declarations of conformity on page 18 gives you information about conformity of AVT cameras.
• Chapter Filter and lenses on page 19 describes the IR cut filter and suit-able camera lenses.
• Chapter Specifications on page 21 lists camera details and spectral sen-sitivity diagrams for each camera type.
• Chapter Camera dimensions on page 29 provides CAD drawings of stan-dard housing (copper and GOF) models, tripod adapter, available angled head models, cross sections of CS-Mount and C-Mount.
• Chapter Camera interfaces on page 35 describes in detail the inputs/outputs of the cameras (incl. Trigger features). For a general description of the interfaces (FireWire and I/O connector) see Hardware Installa-tion Guide.
• Chapter Description of the data path on page 52 describes in detail IIDC conform as well as AVT-specific camera features.
• Chapter Controlling image capture on page 100 describes trigger modi, exposure time, one-shot/multi-shot/ISO_Enable features. Additionally special AVT features are described: sequence mode and secure image signature (SIS).
• Chapter Video formats, modes and bandwidth on page 120 lists all avail-able fixed and Format_7 modes (incl. color modes, frame rates, binning/sub-sampling, AOI=area of interest).
• Chapter How does bandwidth affect the frame rate? on page 142 gives some considerations on bandwidth details.
• Chapter Configuration of the camera on page 145 lists standard and advanced register descriptions of all camera features.
• Chapter Firmware update on page 202 explains where to get information on firmware updates and explains the extended version number scheme of FPGA/µC.
Introduction
OSCAR Technical Manual V2.4.0
14
• Chapter Appendix on page 203 lists the sensor position accuracy of AVT cameras.
• Chapter Index on page 204 gives you quick access to all relevant data in this manual.
Conventions used in this manual
To give this manual an easily understood layout and to emphasize important information, the following typographical styles and symbols are used:
Styles
Symbols
Style Function Example
Bold Programs, inputs or highlighting important things
bold
Courier Code listings etc. Input
Upper case Register REGISTER
Italics Modes, fields Mode
Parentheses and/or blue Links (Link)
Table 2: Styles
Note This symbol highlights important information.
Caution This symbol highlights important instructions. You have to follow these instructions to avoid malfunctions.
www This symbol highlights URLs for further information. The URL itself is shown in blue Color.
Example:
http://www.alliedvisiontec.com
Introduction
OSCAR Technical Manual V2.4.0
15
More information
For more information on hardware and software read the following:• Hardware Installation Guide describes the hardware installation proce-
dures for all 1394 AVT cameras (Dolphin, Oscar, Marlin, Guppy, Pike, Stingray). Additionally you get safety instructions and information about camera interfaces (IEEE1394a/b copper and GOF, I/O connectors, input and output).
Before operation
We place the highest demands for quality on our cameras.
Target group This Technical Manual is the guide to detailed technical information of the camera and is written for experts.
Getting started For a quick guide how to get started read Hardware Installation Guide first.
Note You find the Hardware Installation Guide on the product CD in the following directory:
products\cameras-general
www All software packages (including documentation and release notes) provided by AVT can be downloaded at:
www.alliedvisiontec.com/avt-products/software.html
All software packages are also on AVT’s product CD.
Note Please read through this manual carefully before operat-ing the camera.
For information on AVT accessories and AVT software read Hardware Installation Guide.
Caution Before operating any AVT camera read safety instructions and ESD warnings in Hardware Installation Guide.
Introduction
OSCAR Technical Manual V2.4.0
16
Note To demonstrate the properties of the camera, all examples in this manual are based on the FirePackage OHCI API software and the SmartView application.
www These utilities can be obtained from Allied Vision Technologies (AVT). A free version of SmartView is available for download at:
www.alliedvisiontec.com
Note The camera also works with all IIDC (formerly DCAM) compat-ible IEEE 1394 programs and image processing libraries.
OSCAR cameras
OSCAR Technical Manual V2.4.0
17
OSCAR cameras
Oscar With Oscar cameras, entry into the world of digital image processing is sim-pler and more cost-effective than ever before.
High image quality With the new Oscar, Allied Vision Technologies presents a whole series of attractive digital camera models of the FireWire™ type. The multi-megapixel resolutions, image pre-processing functions, frame grabbing functions and robust industrial casings make them highly suitable for a wide range of dif-ferent applications.
Price-performance In this price class the Oscar sets new standards.
Image applications Oscar cameras offer the perfect solution for applications in medical, micros-copy and general digital image processing.
FireWire The industry standard IEEE 1394 (FireWire or i.Link) facilitates the simplest computer compatibility and bidirectional data transfer using the plug-and-play process. Further development of the IEEE 1394 standard has already made 800 Mbit/second possible – and the FireWire roadmap is already envis-aging 1600 Mbit/second, with 3.2 Gbit/second as the next step. Investment in this standard is therefore secure for the future; each further development takes into account compatibility with the preceding standard, and vice versa, meaning that IEEE 1394b is backward-compatible with IEEE 1394a. Your applications will grow as technical progress advances.
High quality images Operating in 12-bit mode, the cameras provide outstanding image quality under almost all conditions. The Oscar is equipped with an asynchronous trig-ger, true partial scan and numerous smart features for image processing and microscopy. With resolutions of 3, 5 and 8 Megapixel the cameras offer unri-valled solutions for many extreme high resolution applications.
The OSCAR family consists of the following models:
www For further information on the highlights of OSCAR types, the OSCAR family and the whole range of AVT FireWire cam-eras read the data sheets and brochures on the website of Allied Vision Technologies:
www.alliedvisiontec.com
Declarations of conformity
OSCAR Technical Manual V2.4.0
18
Declarations of conformity
Allied Vision Technologies declares under its sole responsibility that the fol-lowing products
to which this declaration relates is in conformity with the following stan-dard(s) or other normative document(s):• FCC Class B• CE (following the provisions of 2004/108/EG directive)• RoHS (2002/95/EC)
Category Name Model Name
Digital camera (IEEE 1394) OSCAR F-320C
OSCAR F-510C
OSCAR F-810C
Table 3: Model names
Filter and lenses
OSCAR Technical Manual V2.4.0
19
Filter and lenses
IR cut filter: spectral transmission
The following illustration shows the spectral transmission of the IR cut filter:
Figure 1: Spectral transmission of Jenofilt 217
Filter and lenses
OSCAR Technical Manual V2.4.0
20
Camera lenses
AVT offers different lenses from a variety of manufacturers. The following table lists selected image formats in width x height depending on camera type, distance and the focal length of the lens.
Note Due to its extreme high resolution, OSCAR cameras place high demands on the modulation transfer function (MTF) of the lens.
If in doubt, ask your dealer for the best lens to fit your appli-cation needs.
Focal lengthfor type 1/1.8 sensorOSCAR F-320C
Distance = 0.5 m Distance = 1 m
4.8 mm 740 mm x 549 mm 1488 mm x 1103 mm
8 mm 441 mm x 327 mm 890 mm x 660 mm
12 mm 292 mm x 216 mm 591 mm x 438 mm
16 mm 217 mm x 161 mm 441 mm x 327 mm
25 mm 136 mm x 101 mm 280 mm x 207 mm
35 mm 95 mm x 71 mm 198 mm x 147 mm
50 mm 65 mm x 48 mm 136 mm x 101 mm
Table 4: Focal length vs. field of view (OSCAR F-320C)
Focal lengthfor type 2/3 sensorOSCAR F-510C/F-810C
Distance = 0.5 m Distance = 1 m
4.8 mm 908 mm x 681 mm 1825 mm x 1368 mm
8 mm 541 mm x 406 mm 1091 mm x 818 mm
12 mm 358 mm x 268 mm 725 mm x 543 mm
16 mm 266 mm x 200 mm 541 mm x 406 mm
25 mm 167 mm x 125 mm 343 mm x 257 mm
35 mm 117 mm x 88 mm 243 mm x 182 mm
50 mm 79 mm x 59 mm 167 mm x 125 mm
Table 5: Focal length vs. field of view (OSCAR F-510C/F-810C)
Specifications
OSCAR Technical Manual V2.4.0
21
Specifications
Oscar F-320C
Note Oscar cameras are always equipped with color sensors.
Note For information on bit/pixel and byte/pixel for each color mode see Table 61: ByteDepth on page 142.
Feature Specification
Image device Type 1/1.8 (diag. 8.93 mm) frame readout SONY CCD ICX-262AQ with HAD microlens
Chip size 8.10 mm x 6.64 mm
Cell Size 3.45 µm x 3.45 µm
Picture size (max.) 2080 x 1540 pixels (Format_7 Mode_0)
Lens mount C-Mount: 17.526 mm (in air); Ø 25.4 mm (32 tpi)
adjustable from 17.3 mm to 22.5 mm
Mechanical flange back to filter distance: 10.5 mm
(see Figure 9: Oscar C-Mount dimensions (standard filter) on page 33)
ADC 12 bit
Color modes Mono8; Y8-green, Y8-red, Y8-blue; RAW8/16; RGB8; YUV4:2:2; YUV4:1:1
Frame rates 3.75 fps; 7.5 fps; 15 fps; 30 fps
Up to 6.59 fps in Format_7 frame readout
Up to 39.31 fps in Format_7 progressive
Gain control Manual: 0-20 dB (0.035 dB/step); auto gain (select. AOI)
Shutter speed 66 µs …67.108.864 µs (~67s); auto shutter (select. AOI)
Table 6: Specification Oscar F-320C
Specifications
OSCAR Technical Manual V2.4.0
22
External trigger shutter Trigger Mode_0, Trigger_Mode_1 (progressive scan, Format_7 Mode_0); advanced feature: Trigger_Mode_15 (bulk); image transfer by command; trigger delay
Internal FIFO memory 32 MByte, optional up to 256 MByte
Look-up tables One, user programmable (12 bit 8/12 bit); gamma (0.5)
Smart functions Real time shading correction, High SNR mode (image summation), image mirror (L-R R-L), sub-sampling, user profilesAWB (auto white balance), color correction, hue, saturation,
Two configurable inputs, two configurable outputs
RS-232 port (serial port, IIDC V1.31)
Transfer rate 100 Mbit/s, 200 Mbit/s, 400 Mbit/s
Digital interface IEEE 1394a IIDC v. 1.3
Power requirements DC 8 V - 36 V via IEEE 1394 cable or 12-pin HIROSE
Power consumption 3.6 watt (@ 12 V DC)
Dimensions 72.5 mm x 44 mm x 44 mm (L x W x H); without tripod and lens
Mass <170 g (without lens and tripod)
Operating temperature +5 ... +45 °Celsius
Storage temperature -10 ... +60 °Celsius
Regulations CE, FCC Class B, RoHS (2002/95/EC)
Standard accessories IR cut filter
Optional accessories Protection glass, locking IEEE 1394 cable
On request Host adapter card, angled head
Software packages API (FirePackage, Active FirePackage, Fire4Linux)
Note The design and specifications for the products described above may change without notice.
Feature Specification
Table 6: Specification Oscar F-320C
Specifications
OSCAR Technical Manual V2.4.0
23
Oscar F-510C
Feature Specification
Image device Type 2/3 (diag. 11 mm) frame readout SONY CCD ICX-282AQ with HAD microlens
Chip size 9.74 mm x 7.96 mm
Cell Size 3.4 µm x 3.4 µm
Picture size (max.) 2588 x 1958 pixels (Format_7 Mode_0)
Lens mount C-Mount: 17.526 mm (in air); Ø 25.4 mm (32 tpi)
adjustable from 17.3 mm to 22.5 mm
Mechanical flange back to filter distance: 10.5 mm
(see Figure 9: Oscar C-Mount dimensions (standard filter) on page 33)
ADC 12 bit
Color modes Mono8; Y8-green, Y8-red, Y8-blue; RAW8/16; RGB8; YUV4:2:2; YUV4:1:1
Frame rates 1.875 fps; 3.75 fps; 7.5 fps
Up to 3.8 fps in Format_7 frame readout
Up to 7.59 fps in Format_7 progressive
Gain control Manual: 0-20 dB (0.035 dB/step); auto gain (select. AOI)
Shutter speed 94 µs …67.108.864 µs (~67s); auto shutter (select. AOI)
External trigger shutter Trigger Mode_0, Trigger_Mode_1 (progressive scan, Format_7 Mode_0); advanced feature: Trigger_Mode_15 (bulk); image transfer by command; trigger delay
Internal FIFO memory 32 MByte, optional up to 256 MByte
Look-up tables One, user programmable (12 bit 8/12 bit); gamma (0.5)
Smart functions Real time shading correction, High SNR mode (image summation), image mirror (L-R R-L), sub-sampling, binning, user profilesAWB (auto white balance), color correction, hue, saturation,
Two configurable inputs, two configurable outputs
RS-232 port (serial port, IIDC V1.31)
Transfer rate 100 Mbit/s, 200 Mbit/s, 400 Mbit/s
Digital interface IEEE 1394a IIDC v. 1.3
Power requirements DC 8 V - 36 V via IEEE 1394 cable or 12-pin HIROSE
Power consumption 3.6 watt (@ 12 V DC)
Dimensions 72.5 mm x 44 mm x 44 mm (L x W x H); without tripod and lens
Table 7: Specification Oscar F-510C
Specifications
OSCAR Technical Manual V2.4.0
24
Mass <170 g (without lens and tripod)
Operating temperature +5 ... +45 °Celsius
Storage temperature -10 ... +60 °Celsius
Regulations CE, FCC Class B, RoHS (2002/95/EC)
Standard accessories IR cut filter
Optional accessories Protection glass, locking IEEE 1394 cable
On request Host adapter card, angled head
Software packages API (FirePackage, Active FirePackage, Fire4Linux)
Note The design and specifications for the products described above may change without notice.
Feature Specification
Table 7: Specification Oscar F-510C
Specifications
OSCAR Technical Manual V2.4.0
25
Oscar F-810C
Feature Specification
Image device Type 2/3 (diag. 11.07 mm) frame readout SONY CCD ICX-456AQ with HAD microlens
Chip size 9.79 mm x 7.93 mm
Cell size 2.7 µm x 2.7 µm
Picture size (max.) 3272 x 2469 pixels (Format_7 Mode_0)
Lens mount C-Mount: 17.526 mm (in air); Ø 25.4 mm (32 tpi)adjustable from 17.3 mm to 22.5 mm
Mechanical flange back to filter distance: 10.5 mm
(see Figure 9: Oscar C-Mount dimensions (standard filter) on page 33)
ADC 12 bit
Color modes Mono8; Y8-green, Y8-red, Y8-blue; Raw8/16; RGB8; YUV422; YUV411
Frame rates 3.75 fps; 7.5 fps
Up to 3.15 fps in Format_7 frame readout
Up to 8.88 fps in Format_7 progressive
Gain control Manual: 0-20 dB (0.035 dB/step); auto gain (select. AOI)
Shutter speed 118 µs …67.108.864 µs (~67s); auto shutter (select. AOI)
External trigger shutter Trigger Mode_0, Trigger_Mode_1 (progr. scan, Format_7 Mode_0); advanced feature: Trigger_Mode_15 (bulk); image transfer by com-mand; trigger delay
Internal FIFO memory 64 MByte, optional up to 256 MByte
Look-up tables One, user programmable (12 bit 8/12 bit); gamma (0.5)
Smart functions Real time shading correction, High SNR mode (image summation), image mirror (L-R R-L), sub-sampling, user profilesAWB (auto white balance), color correction, hue, saturation
Two configurable inputs, two configurable outputs
RS-232 port (serial port, IIDC V1.31)
Transfer rate 100 Mbit/s, 200 Mbit/s, 400 Mbit/s
Digital interface IEEE 1394a IIDC v. 1.3
Power requirements DC 8 V - 36 V via IEEE 1394 cable or 12-pin HIROSE
Power consumption 3.6 watt (@ 12 V DC)
Dimensions 72.5 mm x 44 mm x 44 mm (L x W x H); without tripod and lens
Table 8: Specification Oscar F-810C
Specifications
OSCAR Technical Manual V2.4.0
26
Mass <170 g (without lens and tripod)
Operating temperature +5 ... +45 °Celsius
Storage temperature -10 ... +60 °Celsius
Regulations CE, FCC Class B, RoHS (2002/95/EC)
Standard accessories IR cut filter
Optional accessories Protection glass, locking IEEE 1394 cable
On request Host adapter card, angled head
Software packages API (FirePackage, Active FirePackage, Fire4Linux)
Note The design and specifications for the products described above may change without notice.
Feature Specification
Table 8: Specification Oscar F-810C
Specifications
OSCAR Technical Manual V2.4.0
27
Spectral sensitivity
Figure 2: Spectral sensitivity of Oscar F-320C without cut filter and optics
Figure 3: Spectral sensitivity of Oscar F-510C without cut filter and optics
Specifications
OSCAR Technical Manual V2.4.0
28
Figure 4: Spectral sensitivity of Oscar F-810C without cut filter and optics
Camera dimensions
OSCAR Technical Manual V2.4.0
29
Camera dimensions
Oscar standard housing
Note For information on sensor position accuracy:
(sensor shift x/y, optical back focal length z and sensor rota-tion α) see Chapter Sensor position accuracy of AVT cameras on page 203.
Figure 5: Camera dimensions
☺
Body size: 72.5 mm x 44 mm x 44 mm (L x W x H)Mass: 170 g (without lens)
Camera dimensions
OSCAR Technical Manual V2.4.0
30
Oscar W90
This version has the sensor tilted by 90 degrees clockwise, so that it views upwards.
Note An additional specification is required for the rotation of the sensor.
Figure 6: Oscar W90
Camera dimensions
OSCAR Technical Manual V2.4.0
31
Oscar W270
This version has the sensor tilted by 270 degrees clockwise, so that it views downwards.
Please note that an additional specification is required for the rotation of the sensor.
Figure 7: Oscar W270
Camera dimensions
OSCAR Technical Manual V2.4.0
32
Tripod adapter
Figure 8: Tripod dimensions
Camera dimensions
OSCAR Technical Manual V2.4.0
33
Cross section: C-Mount (standard filter)
All Oscar cameras are equipped with standard filter.
Figure 9: Oscar C-Mount dimensions (standard filter)
Camera dimensions
OSCAR Technical Manual V2.4.0
34
Adjustment of C-Mount
Oscar cameras allow the precise adjustment of the back focus of the C-Mount by means of a back focus ring which is threaded into the C-Mount and held by two screws on either side of the camera. The mechanical adjustment of the imaging device is important in order to achieve a perfect alignment with the focal point of the lens.
This adjustment is made before leaving the factory to conform to the stan-dard of 17.526 mm and should normally not require adjustment in the field.
However, if the back focal plane of your lens does not conform to the C-Mount back-focus specification, renewed adjustment may be required in the field.
How to proceed:
1. Loosen screws (location as shown above by arrow) with an Allen key (1.3 x 50; Order#: K 9020411).
2. With the lens set to infinity or a known focus distance, set the camera to view an object located at 'infinity' or the known distance.
3. Rotate the C-Mount ring and lens forward or backwards on its thread until the object is in sharp focus. Be careful that the lens remains seated in the C-Mount.
4. Once focus is achieved, tighten the two locking screws without applying excessive torque.
Figure 10: Back focus adjustment
Camera interfaces
OSCAR Technical Manual V2.4.0
35
Camera interfaces
This chapter gives you detailed information on status LEDs, inputs and out-puts, trigger features and transmission of data packets.
IEEE 1394a port pin assignment
The IEEE 1394 plug is designed for industrial use and has the following pin assignment as per specification:
Note For a detailed description of the camera interfaces (FireWire, I/O connector), ordering numbers and operat-ing instructions see the Hardware Installation Guide, Chapter Camera interfaces.
Read all Notes and Cautions in the Hardware Installation Guide, before using any interfaces.
Figure 11: IEEE 1394a connector
Pin Signal
1 Cable power
2 Cable GND
3 TPB-
4 TPB+
5 TPA-
6 TPA+
Camera interfaces
OSCAR Technical Manual V2.4.0
36
Camera I/O pin assignment
Figure 12: Camera I/O connector pin assignment
Note GP = General Purpose
For a detailed description of the I/O connector and its oper-ating instructions see the Hardware Installation Guide, Chapter OSCAR input description.
Read all Notes and Cautions in the Hardware Installation Guide, before using the I/O connector.
1
102
9
8
7
6
12113
45
Pin Signal Direction Level Description
1 External GND GND for RS232 and ext. power
External ground for RS232 and external power
2 External Power +8 ... +36 V DC Power supply
3
4 Camera In 1 In Uin(high) = 2 V...UinVCCUin(low) = 0 V...0.8 V
Camera Input 1(GPIn1)default: Trigger
5
6 Camera Out 1 Out Open emitter Camera Output 1(GPOut1)default: IntEna
7 Camera In GND In Common GND for inputs
Camera Common Input Ground(In GND)
8 RxD RS232 In RS232 Terminal Receive Data
9 TxD RS232 Out RS232 Terminal Transmit Data
10 Camera Out Power In Common VCC for outputsmax. 36 V DC
Camera Output Powerfor digital outputs(OutVCC)
11 Camera In 2 In Uin(high) = 2 V...UinVCCUin(low) = 0 V...0.8 V
Camera Input 2(GPIn2)default: -
12 Camera Out 2 Out Open emitter Camera Output 2(GPOut2)default: -
Camera interfaces
OSCAR Technical Manual V2.4.0
37
Status LEDs
On LEDThe green power LED indicates that the camera is being supplied with suffi-cient voltage and is ready for operation.
Status LED (yellow)The following states are displayed via the LED:
Figure 13: Position of Status LEDs
State Description
Com Asynchronous and isochronous data transmission active (indicated asynchronously to transmission over the 1394 bus)
Trg LED off - waiting for external trigger
LED on - receiving external trigger
Table 9: LED indication
Status LEDs
Camera interfaces
OSCAR Technical Manual V2.4.0
38
Blink codes are used to signal warnings or error states:
The longer OFF-time of 3.5 sec. signals the beginning of a new class period. The error codes follow after a shorter OFF-time of 1.5 sec.
Example 3.5 sec. one blink 1.5 sec. 2 blinks
indicates a warning: Format_7_Error_1
Class S1
Error codes S2
Warning1 blink
DCAM2 blinks
MISC3 blinks
FPGA4 blinks
Stack5 blinks
FPGA boot error 1-5 blinks
Stack setup 1 blink
Stack start 2 blinks
No FLASH object 1 blink
No DCAM object 1 blink
Register mapping 2 blinks
VMode_ERROR_STATUS 1 blink
FORMAT_7_ERROR_1 2 blinks
FORMAT_7_ERROR_2 3 blinks
Table 10: Error codes
Camera interfaces
OSCAR Technical Manual V2.4.0
39
Control and video data signals
The inputs and outputs of the camera can be configured by software. The dif-ferent modes are described below.
Inputs
Triggers
All inputs configured as triggers are linked by logical AND function. If two inputs are being used as triggers, a high signal at the output of the block must be present on all inputs in order to generate a trigger signal. The polar-ity for each signal can be set separately via the inverting inputs. The camera must be set to external triggering to trigger image capture by the trigger signal.
Note For a general description of the inputs and warnings see the Hardware Installation Guide, Chapter OSCAR input descrip-tion.
Figure 14: Input block diagram
Input
Polarity
selectablevia software
Input state
Opto-
Coupler
Input signal
Trigger-AND
Input 2, if set to trigger
Camera interfaces
OSCAR Technical Manual V2.4.0
40
Input/output pin controlAll input and output signals running over the camera I/O connector are con-trolled by an advanced feature register.
Register Name Field Bit Description
0xF1000300 IO_INP_CTRL1 Presence_Inq [0] Indicates presence of this feature (read only)
--- [1..6] Reserved
Polarity [7] 0: low active
1: high active
--- [8..10] Reserved
InputMode [11..15] Mode
see Table 12: Input routing on page 41
--- [16..30] Reserved
PinState [31] RD: Current state of pin
0xF1000304 IO_INP_CTRL2 Same as IO_INP_CTRL1
Table 11: Advanced register: Input control
Camera interfaces
OSCAR Technical Manual V2.4.0
41
IO_INP_CTRL 1-2
The Polarity flag determines whether the input is low active (0) or high active (1). The input mode can be seen in the following table. The PinState flag is used to query the current status of the input.
• For inputs, the PinState bit refers to the inverted out-
put side of the optical coupler. This signals that an open input sets the PinState bit to 1.
ID Mode Default
0x00 Off
0x01 Reserved
0x02 Trigger input Input 1
0x03 Reserved
0x06..0x0F Reserved
0x10..0x1F Reserved
Table 12: Input routing
Note If you set more than 1 input to function as a trigger input, all trigger inputs are ANDed.
Camera interfaces
OSCAR Technical Manual V2.4.0
42
Trigger delay
Oscar cameras feature various ways to delay image capture based on an exter-nal trigger.
With IIDC V1.31 there is a standard CSR at register F0F00534/834h to control a delay up to FFFh x time base value.
The following table explains the inquiry register and the meaning of the var-ious bits.
Register Name Field Bit Description
0xF0F00534 TRIGGER_DELAY_INQUIRY Presence_Inq [0] Indicates presence of this feature (read only)
Abs_Control_Inq [1] Capability of control with absolute value
--- [2] Reserved
One_Push_Inq [3] One Push auto mode (Con-trolled automatically by the camera once)
Readout_Inq [4] Capability of reading out the value of this feature
ON_OFF [5] Capability of switching this feature ON and OFF
Auto_Inq [6] Auto Mode (Controlled auto-matically by the camera)
Manual_Inq [7] Manual Mode (Controlled by user)
Min_Value [8..19] Minimum value for this fea-ture
Max_Value [20..31] Maximum value for this fea-ture
Table 13: Trigger delay inquiry register
Camera interfaces
OSCAR Technical Manual V2.4.0
43
The cameras also have an advanced register which allows even more precise image capture delay after receiving a hardware trigger.
Trigger delay advanced register
The advanced register allows the start of the integration to be delayed by max. 221 µs, which is max. 2.1 s after a trigger edge was detected.
Register Name Field Bit Description
0xF0F00834 TRIGGER_DELAY Presence_Inq [0] Presence of this feature:
0: N/A
1: Available
Abs_Control [1] Absolute value control
O: Control with value in the value field
1: Control with value in the absolute value CSRIf this bit= 1 the value in the value field has to be ignored.
--- [2..5] Reserved
ON_OFF [6] Write ON or OFF this feature
Read: Status of the feature
ON=1
OFF=0
--- [7..19] Reserved
Value [20..31] Value
Table 14: Trigger Delay CSR
Register Name Field Bit Description
0xF1000400 TRIGGER_DELAY Presence_Inq [0] Indicates presence of this feature (read only)
--- [1..5] Reserved
ON_OFF [6] Trigger delay on/off
--- [7..10] Reserved
DelayTime [11..31] Delay time in µs
Table 15: Trigger delay advanced CSR
Camera interfaces
OSCAR Technical Manual V2.4.0
44
Outputs
Output features are configured by software. Any signal can be placed on any output.
The main features of output signals are described below:
Note • Switching trigger delay to ON also switches external Trigger_Mode_0 to ON.
• This feature works with external Trigger_Mode_0 only.
Note For a general description of the outputs and warnings see the Hardware Installation Guide, Chapter OSCAR output description.
Signal Description
IntEna (Integration Enable) signal This signal displays the time in which exposure was made. By using a register, this output can be delayed by up to 1.05 seconds. This signal can be used to fire a strobe flash.
Fval (Frame valid) signal This feature signals readout from the sensor. This signal Fval follows IntEna.
Busy signal This signal appears when:
• the exposure is being made or• the sensor is being read out or• data transmission is active.
The camera is busy.
Table 16: Output signals
Camera interfaces
OSCAR Technical Manual V2.4.0
45
Figure 15: Output block diagram
IntEna
Output signalOpto-
Coupler
Polarity
selectablevia software
Operation state read
FVal
Busy
Operation state read
Output mode
selectablevia software
Camera interfaces
OSCAR Technical Manual V2.4.0
46
IO_OUTP_CTRL 1-2
The outputs (Output mode, Polarity) are controlled via two advanced feature registers.
The Polarity flag determines whether the output is active low (0) or active high (1). The output mode can be viewed in the table below. The current status of the output can be queried and set via the PinState flag.
It is possible to read back the status of an output pin regardless of the output mode. This allows for example the host computer to determine if the camera is busy by simply polling the BUSY output.
Register Name Field Bit Description
0xF1000320 IO_OUTP_CTRL1 Presence_Inq [0] Indicates presence of this feature (read only)
--- [1..6] Reserved
Polarity [7] 0: active low
1: active high (inverting)
--- [8..10] Reserved
Output mode [11..15] Mode
see Table 18: Output rout-ing on page 47
--- [16..30] Reserved
PinState [31] RD: Current state of pin
WR: New state of pin
0xF1000324 IO_OUTP_CTRL2 Same as IO_OUTP_CTRL1
Table 17: Advanced register: Output control
Camera interfaces
OSCAR Technical Manual V2.4.0
47
Output modes
The Polarity setting refers to the input side of the optical coupler output. PinState 0 switches off the output transistor and produces a low level over the resistor connected from the output to ground.
The following diagram illustrates the dependencies of the various output sig-nals.
ID Mode Default
0x00 Off
0x01 Output state follows PinState bit Using this mode, the Polarity bit has to be set to 0 (not inverted). This is necessary for an error free display of the output status.
0x02 Integration enable Output 1
0x03 Reserved
0x04 Reserved
0x05 Reserved
0x06 FrameValid
0x07 Busy Output 2
0x08 Follow corresponding input(Inp1 Out1, Inp2 Out2, …)
0x09..0x0F Reserved
0x10..0x1F Reserved
Table 18: Output routing
Camera interfaces
OSCAR Technical Manual V2.4.0
48
Figure 16: Output impulse diagram
Note The signals can be inverted.
Note • Note that trigger delay in fact delays the image cap-ture whereas the IntEna_Delay only delays the leading edge of the IntEna output signal but does not delay the image capture.
• As mentioned before, it is possible to set the outputs by software. Doing so, the achievable maximum fre-quency is strongly dependent on individual software capabilities. As a rule of thumb, the camera itself will limit the toggle frequency to not more than 700 Hz.
• In split shutter mode the camera will issue two (Oscar F-810C: three) IntEnas and FrameValids but only one Busy, because it integrates the two (Oscar F-810C: three) fields separately.
Camera interfaces
OSCAR Technical Manual V2.4.0
49
Pixel data
Pixel data are transmitted as isochronous data packets in accordance with the 1394 interface described in IIDC V1.3. The first packet of a frame is iden-tified by the 1 in the sync bit (sy) of the packet header.
• The video data for each pixel are output in either 8-bit or 12-bit format. • Each pixel has a range of 256 or 4096 shades of gray.• The digital value 0 is black and 255 or 4095 is white. In 16-bit mode
the data output is MSB aligned.
Field Description
data_length Number of bytes in the data field
tg Tag field
shall be set to zero
channel Isochronous channel number, as programmed in the iso_channel field of the cam_sta_ctrl register
tCode Transaction code
shall be set to the isochronous data block packet tCode
sy Synchronization value (sync bit)
This is one single bit. It indicates the start of a new frame.
It shall be set to 0001h on the first isochronous data block of a frame, and shall be set to zero on all other isochronous blocks
Video data payload Shall contain the digital video information
Table 20: Description of data block packet format
0-7 8-15 16-23 24-31
data_length tg channel tCode sy
header_CRC
Video data payload
data_CRC
Table 19: Isochronous data block packet format. Source: IIDC V1.3
sync bit
Camera interfaces
OSCAR Technical Manual V2.4.0
50
The following table provides a description of the video data format for the different modes. (Source: IIDC V1.3)
Figure 17: YUV 4:2:2 and YUV 4:1:1 format: Source: IIDC V1.3
Figure 18: Y8 and Y16 format: Source: IIDC V1.3
Camera interfaces
OSCAR Technical Manual V2.4.0
51
Figure 19: Data structure: Source: IIDC V1.3
Description of the data path
OSCAR Technical Manual V2.4.0
52
Description of the data path
Block diagram of the camerasThe following diagram illustrates the data flow and the bit resolution of image data after being read from the CCD sensor chip in the camera. The indi-vidual blocks are described in more detail in the following paragraphs. For sensor data see Chapter Specifications on page 21.
Figure 20: Block diagram Oscar cameras
Se
nso
rA
na
log
Ca
me
ra C
on
tro
l
HiRose I/O
RS232
De
-Ba
ye
rin
gR
1G
1R
2G
2
G3
B1
G4
B2
P 1
P 2
P 3
CC
D:
An
alo
g F
ron
t E
nd
(A
FE
)
8/1
2 B
it
Test-Pattern Auto-Data
10 Bit
8 B
itF
ram
e-
Me
mo
ry8
/12
Bit
Gra
ph
ics
Overlay
12
Bit
Ho
rizo
nta
l
Mirro
r1
2 B
itH
ori
zo
nta
l
Ma
skin
g
Sh
arp
ne
ss
Params
Ca
me
ra C
on
tro
l
Off
se
t
An
alo
g
Ga
in
12
Bit
Wh
ite
Ba
lan
ce
12 B
itS
ha
din
g
Corr
ection
12
Bit
LU
T
12 Bit (LUT off)
8 Bit (LUT on)
10
Bit
Mu
ltip
le C
olo
r
Opera
tions
(RG
B->
YU
V,
Hu
e,
Sa
tura
tio
n)
8 B
it
RA
W-M
od
e
MU
X8
/12
Bit
IEE
E-1
39
4
Inte
rfa
ce
1394a
Description of the data path
OSCAR Technical Manual V2.4.0
53
Black and white output interpolation modes
Various black and white output interpolation modes have been implemented in the data path to ensure high quality black and white image output.
The cameras are able to output:• B/w signal out of luma interpolation formula (Y = 0.3R + 0.6G + 0.1B)• B/w signal out of RED channel information• B/w signal out of GREEN channel information• B/w signal out of BLUE channel information
For certain applications where the camera is imposed to monochromatic light, it may be advantageous (in terms of reduced noise) to use only the respective color channel instead of the fully interpolated luma signal.
Example: If you illuminate a scene with green light, the use of b/w output from the GREEN channel may give better image with less noise than b/w out of luma.
The b/w image is also spatially interpolated, so that it has the same amount of pixels as the color image.
Read out modes of the sensor
In order to achieve the highest possible sensitivity, all sensors are equipped with micro lenses, and read-out in the so called frame readout mode. This is a special frame integration interlaced field readout mode, very similar to the interlaced mode of conventional video cameras.
Whereas Oscar F-320C and Oscar F-510C have two field readouts, the Oscar F-810C is equipped with a three field readout sensor.
The conversion from interlaced to progressive takes place in the camera's internal memory.
Special sub-sampling modes allow faster progressive scan readouts, while maintaining the same imaging conditions. These modes can be effectively used for focus and aperture adjustment operations.
The following samples are taken out of the data sheets of the sensors, detail-ing the various modes.
Note Spatial resolution is because of the present BAYER Mosaic fil-ter nevertheless only half of that in each direction of a (fic-tive) b/w sensor.
Description of the data path
OSCAR Technical Manual V2.4.0
54
Oscar F-320C: ICX-262AQ readout scheme
The screenshot below, taken from the Oscar F-320C sensor's data sheet, shows the ICX-262AQ readout scheme.
Frame readout mode reads out red and green color pixels in the first field, followed by the green and blue pixels in the second field.
1. Frame readout modeIn this mode, all pixel signals are divided into two fields and output.All pixel signals are read out independently, making this mode suitable for high resolution image capturing.
Note The high frame readout mode reads out 2 from 12 lines and thus achieves a remarkably high frame rate of nearly 40 fps.
Figure 21: Oscar F-320C: Sony ICX-262AQ readout scheme
Note Blacked out portions in the diagram indicate pixels which are not read out.
Description of the data path
OSCAR Technical Manual V2.4.0
55
2. High frame rate readout modeOutput is performed at 30 frames per second by reading out 2 pixels for every 12 vertical pixels.The number of output lines is 258 lines.This readout mode emphasizes processing speed over vertical resolu-tion.
Oscar F-510C: ICX-282AQ readout scheme
Oscar F-510C is equipped with the ICX-282AQ sensor.
Frame readout is again two fields and has the two primary colors, red and blue, read out in separate fields.
Progressive mode reads out two from four lines achieving a moderate speed increase but progressive scan with megapixel resolution.
The readout scheme of it is shown below:
Figure 22: Oscar F-510C: Sony ICX-282AQ readout scheme
Description of the data path
OSCAR Technical Manual V2.4.0
56
Oscar F-810C: ICX-456AQ readout scheme
Oscar F-810C uses the ICX-456AQ sensor with three field readout mode. Every field skips two lines during read out, so all primary colors of the BAYER mosaic are read out in every field.
Progressive scan mode reads out 2 out of 6 lines.
Figure 23: Oscar F-810C: Sony ICX-456AQ readout scheme
Description of the data path
OSCAR Technical Manual V2.4.0
57
Frame readout implications
Frame readout has implications when shooting moving or stationary objects.
To compensate for this condition, two different shutter modes have been introduced.
The so-called split shutter opens and closes the shutter per field. This mode is suitable for shooting stationary objects only.
Split shutter can be used with continuous light or strobe light because the camera outputs the IntEna signal accurately per field (this means that in the case of an Oscar F-810C, a strobe would flash three times per image).
The so-called joint shutter opens the shutter for both fields concurrently. When the first field is shifted into the shift register its integration ends, but the integration of the second (or third) field continues until the previous field(s) has(ve) been completely shifted out.
Consequently the shutter time can only be controlled for the first field; the other field(s) always have an additional shutter time equivalent to the read-out time of the first field.
Figure 24: Split shutter
Note Using this mode with moving objects introduces red/blue artefacts with the Oscar F-320C and Oscar F-510C, and jagged artefacts with the Oscar F-810C.
Shutter first
field
Output first field
Output second field
Shutter
second field
Description of the data path
OSCAR Technical Manual V2.4.0
58
The following pre-requisites are necessary to handle moving image acquisi-tion in joint shutter mode:• Strobe light and• Ambient light reduced by proper light shields or• Mechanical external shutter• LCD optical shutter
Figure 25: Joint shutter
Note Consult the factory or your local dealer if you have special applications requiring external shutters.
Shutter first
field
Output first field to camera
buffer
Output second field to
camera buffer
Shutter second field
Exposure
(Flash)
Description of the data path
OSCAR Technical Manual V2.4.0
59
White balance
Oscar cameras have both manual and automatic white balance.
White balance is applied so that non-colored image parts are displayed non-colored.
White balance does not use the so called PxGA® (Pixel Gain Amplifier) of the analog front end (AFE) but a digital representation in the FPGA in order to modify the gain of the two channels with lower output by +9.5 dB (in 512 steps) relative to the channel with highest output.
The following screenshot is taken from the data sheet of the AFE and illus-trates the details:
The analog color signal, coming in pulse amplitude modulation from the sen-sor is in the form of the BAYER™ color pattern sequence. It is initially pro-cessed in the CDS (correlated double sampler) and then bypasses the PxGA before further amplification and digitization.
Figure 26: Block diagram of AFE (Source: Analog Devices)
Description of the data path
OSCAR Technical Manual V2.4.0
60
From the user's point of view, the white balance settings are made in register 80Ch of IIDC V1.3. This register is described in more detail below.
The values in the U/B_Value field produce changes from green to blue; the V/R_Value field from green to red as illustrated below.
Register Name Field Bit Description
0xF0F0080C WHITE_BALANCE Presence_Inq [0] Presence of this feature:
0: N/A;1: Available
Abs_Control [1] Absolute value controlO: Control with value in the Value field1: Control with value in the Absolute value CSRIf this bit=1, the value in the Value field will be ignored.
--- [2..4] Reserved
One_Push [5] Write 1: begin to work (self-cleared after operation)Read:1: in operation0: not in operationIf A_M_Mode = 1, this bit will be ignored.
ON_OFF [6] Write: ON or OFF this featureRead: read a status0: OFF1: ON
A_M_MODE [7] Write: set modeRead: read current mode0: MANUAL1: AUTO
U/B_Value [8..19] U/B valueThis field is ignored when writing the value in Auto or OFF mode.If readout capability is not available, read-ing this field has no meaning.
V/R_Value [20..31] V/R value
This field is ignored when writing the value in Auto or OFF mode.If readout capability is not available, read-ing this field has no meaning.
Table 21: White balance register
Description of the data path
OSCAR Technical Manual V2.4.0
61
One-push automatic white balance
The camera automatically generates frames, based on the current settings of all registers (GAIN, OFFSET, SHUTTER, etc.).
For white balance, in total 9 frames are processed, and a grid of at least 300 samples is equally spread over the work area. This area can be the field of view or a subset of it. The R-G-B component values of the samples are added and used as current values for both the one-push and the automatic white balance.
This feature uses the assumption that the R-G-B component sums of the sam-ples are equal; i.e., it assumes that the average of the sampled grid pixels is to be monochrome.
Figure 27: U/V slider range
Note Configuration
To configure this feature in control and status register (CSR): See Chapter White balance register on page 60.
To activate one-push automatic white balance: Set one-push bit in the WHITE_BALANCE register.
Note The following ancillary conditions should be observed for suc-cessful white balance:
• There are no stringent or special requirements on the image content, it requires only the presence of mono-chrome pixels in the image.
• Automatic white balance can be started both during active image capture and when the camera is in idle state.
Description of the data path
OSCAR Technical Manual V2.4.0
62
If the image capture is active (e.g. IsoEnable set in register 614h), the frames used by the camera for white balance are also output on the 1394 bus. Any previously active image capture is restarted after the completion of white balance.
Automatic white balance can also be enabled by using an external trigger. However, if there is a pause of >10 seconds between capturing individual frames, this process is aborted.
The following flow diagram illustrates the automatic white balance sequence.
Finally, the calculated correction values can be read from the WHITE_BALANCE register 80Ch.
Figure 28: Auto white balance sequence
Pause image capture
Capture image via One_shot
Calculate and set correction
values
Restart image capture if necessary
Repeat steps nine times
Description of the data path
OSCAR Technical Manual V2.4.0
63
Automatic white balanceThe auto white balance feature continuously optimizes the color characteris-tics of the image.
As a reference, it uses a grid of at least 300 samples equally spread over the area of interest or a fraction of it.
AUTOFNC_AOI affects the auto shutter, auto gain and auto white balance fea-tures and is independent of the Format_7 AOI settings. If this feature is switched off, the work-area position and size represent the current active image size.
Within this area, the R-G-B component values of the samples are added and used as current values for the feedback.
The following drawing illustrates the AUTOFNC_AOI settings in greater detail.
Note Configuration
To set position and size of the control area (Auto_Function_AOI) in an advanced register: see Table 95: Advanced register: Autofunction AOI on page 193.
Figure 29: AUTOFNC_AOI positioning
AO
I: Y-size
AOI: X-size
AF_AREA_SIZE: Width: n x 128
AF_AR
EA_S
IZE: H
eight: n x 128
0,0
AF_AREA_POSITION: Left,Top
Sampling grid for Auto-Function
Description of the data path
OSCAR Technical Manual V2.4.0
64
The algorithm bases on the assumption that the R-G-B component sums of the samples are equal, i.e., it assumes that the mean of the sampled grid pix-els is to be monochrome.
Visualization of the AUTOFNC_AOI is carried out with the help of the graphics overlay function of the camera (see Chapter Block diagram of the cameras on page 52). This area is highlighted when the Show work area bit is set high.
Manual gain
As shown in Figure 26: Block diagram of AFE (Source: Analog Devices) on page 59, all cameras are equipped with a gain setting, allowing the gain to be manually adjusted on the fly by means of a simple command register write.
The following ranges can be used when manually setting the gain for the ana-log video signal:
The increment length is ~0.0351 dB/step.
Note The algorithm will try to create an uncolored image when looking at an area that is completely colored with automatic white balance ON.
Type Range Range in dB
All Oscar cameras 0 ... 570 0 … 20 dB
Table 22: Manual gain range of the various Oscar types
Note • Setting the gain does not change the offset (black value).
• A higher gain also produces greater image noise. This reduces image quality. For this reason, first try to increase the brightness, using the aperture of the cam-era optics and/or longer shutter settings.
• Generally all Oscar cameras enable certain image set-tings to be modified on the fly, e.g. gain and shutter can be changed by the host computer by writing into the gain and shutter register even during camera opera-tion. An uncertainty of one or two images remains because the host is unaware (especially with external trigger) of when the next image will arrive.
Description of the data path
OSCAR Technical Manual V2.4.0
65
Auto gain
In combination with auto white balance, all Oscar cameras are equipped with auto gain feature.
When enabled auto gain adjusts the gain within the default gain limits or within the limits set in advanced register F1000370h in order to reach the brightness set in auto exposure register as reference.
Increasing the auto exposure value (aka target grey value) increases the aver-age brightness in the image and vice versa.
The applied algorithm uses a proportional plus integral controller (PI control-ler) to achieve minimum delay with zero overshot.
The following tables show the gain and auto exposure CSR.
Register Name Field Bit Description
0xF0F00820 GAIN Presence_Inq [0] Presence of this feature:0: N/A1: Available
Abs_Control [1] Absolute value controlO: Control with value in the value field1: Control with value in the absolute value CSRIf this bit=1 the value in the value field has to be ignored.
--- [2..4] Reserved
One_Push [5] Write: Set bit high to startRead: Status of the feature:Bit high: WIPBit low: Ready
ON_OFF [6] Write: ON or OFF this featureRead: read a status0: OFF1: ON
A_M_MODE [7] Write: set modeRead: read current mode0: MANUAL1: AUTO
--- [8..19] Reserved
Value [20..31] Read/Write ValueThis field is ignored when writing the value in Auto or OFF mode.If readout capability is not available, reading this field has no meaning.
Table 23: CSR: Gain
Description of the data path
OSCAR Technical Manual V2.4.0
66
Register Name Field Bit Description
0xF0F00804 AUTO_EXPOSURE Presence_Inq [0] Presence of this feature:0: N/A1: Available
Abs_Control [1] Absolute value controlO: Control with value in the value field1: Control with value in the absolute value CSRIf this bit=1, the value in the value field has to be ignored.
--- [2..4] Reserved
One_Push [5] Write: Set bit high to starRead: Status of the feature:bit high: WIPbit low: Ready
ON_OFF [6] Write ON or OFF this feature, ON=1
Read: Status of the feature, OFF=0
A_M_MODE [7] Set bit high for Auto feature
Read for Mode
0=MANUAL1=AUTO
--- [8..19] Reserved
Value [20..31] Read/Write value
This field is ignored when writing the value in Auto or OFF mode.
If readout capability is not available, reading this field has no meaning.
Table 24: CSR: Auto Exposure
Note Configuration
To configure this feature in an advanced register: See Table 94: Advanced register: Auto gain control on page 192.
Description of the data path
OSCAR Technical Manual V2.4.0
67
Brightness (black level or offset)
It is possible to set the black level in the camera within the following ranges:
0...+16 gray values (@ 8 bit)
Increments are in 1/16 LSB (@ 8 bit)
The formula for gain and offset setting is: Y’ = G x Y + Offset
Note • Values can only be changed within the limits of gain CSR.
• Changes in auto exposure register only have an effect when auto gain is active.
• Auto exposure limits are 50..205. (SmartView Ctrl1 tab: Target grey level)
Note • Setting the gain does not change the offset (black value).
Description of the data path
OSCAR Technical Manual V2.4.0
68
The IIDC brightness register at offset 800h is used for this purpose.
The following table shows the BRIGHTNESS register.
Register Name Field Bit Description
0xF0F00800 BRIGHTNESS Presence_Inq [0] Presence of this feature:0: N/A1: Available
Abs_Control [1] Absolute value controlO: Control with value in the value field1: Control with value in the absolute value CSRIf this bit= 1 the value in the value field has to be ignored
--- [2..4] Reserved
One_Push [5] Write: Set bit high to startRead: Status of the feature:
Bit high: WIP
Bit low: Ready
ON_OFF [6] Write: ON or OFF this feature
Read: read a status
0: OFF1: ON
A_M_MODE [7] Write: set modeRead: read current mode
0: MANUAL1: AUTO
--- [8..19] Reserved
Value [20..31] Read/Write Value; this field is ignored when writing the value in Auto or OFF mode; if readout capability is not avail-able reading this field has no meaning.
Table 25: CSR: Brightness
Description of the data path
OSCAR Technical Manual V2.4.0
69
Auto shutter
In combination with auto white balance, Oscar cameras are equipped with an auto shutter feature.
When enabled, the auto shutter adjusts the shutter within the default shutter limits or within those set in advanced register F1000360h in order to reach the reference brightness set in auto exposure register.
Increasing the auto exposure value increases the average brightness in the image and vice versa.
The applied algorithm uses a proportional plus integral controller (PI control-ler) to achieve minimum delay with zero overshot.
Note Target grey level parameter in SmartView corresponds to Auto_exposure register 0xF0F00804 (IIDC).
Description of the data path
OSCAR Technical Manual V2.4.0
70
To configure this feature in control and status register (CSR):
Register Name Field Bit Description
0xF0F0081C SHUTTER Presence_Inq [0] Presence of this feature:0: N/A1: Available
Abs_Control [1] Absolute value controlO: Control with value in the value field1: Control with value in the absolute value CSRIf this bit=1, the value in the value field has to be ignored.
--- [2..4] Reserved
One_Push [5] Write 1: begin to work (self-cleared after oper-ation)Read:1: in operation0: not in operationIf A_M_Mode = 1, this bit will be ignored.
ON_OFF [6] Write: ON or OFF this featureRead: read a status0: OFF1: ON
A_M_MODE [7] Write: set modeRead: read current mode0: MANUAL1: AUTO
--- [8..19] Reserved
Value [20..31] Read/Write ValueThis field is ignored when writing the value in Auto or OFF mode.If readout capability is not available, reading this field has no meaning.
Table 26: CSR: Shutter
Note Configuration
To configure this feature in an advanced register: See Table 93: Advanced register: Auto shutter control on page 192.
Description of the data path
OSCAR Technical Manual V2.4.0
71
Look-up table (LUT) and gamma function
The AVT Oscar camera provides one user-defined look-up table (LUT). The use of this LUT allows any function (in the form Output = F(Input)) to be stored in the camera's RAM and to be applied on the individual pixels of an image at run-time.
The address lines of the RAM are connected to the incoming digital data, these in turn point to the values of functions which are calculated offline, e.g. with a spreadsheet program.
This function needs to be loaded into the camera's RAM before use.
One example of using a LUT is the gamma LUT:
Output = (Input)0.5
This gamma LUT is used with all Oscar models.
It is known as compensation for the nonlinear brightness response of many displays e.g. CRT monitors. The look-up table converts the incoming 12 bit from the digitizer to outgoing 8 bit.
Figure 30: Gamma LUT
Output = (Input)gamma
0
50
100
150
200
250
0 500 1000 1500 2000 2500 3000 3500 4000
Input
Outp
ut
Oscar, gamma=0.5
Description of the data path
OSCAR Technical Manual V2.4.0
72
Note • The input value is the most significant 12-bit value from the digitizer. The gamma LUT outputs the most significant 8 bit as shown above.
• As gamma correction is also implemented via the LUT, it is not possible to use a different LUT when gamma correction is enabled.
• After overriding the LUT with a user defined content, gamma functionality is no longer available until the next full initialization of the camera.
• LUT content is volatile if you do not use the user pro-files to save the LUT.
Description of the data path
OSCAR Technical Manual V2.4.0
73
Loading an LUT into the cameraLoading the LUT is carried out through the data exchange buffer called GPDATA_BUFFER. As this buffer can hold a maximum of 2 kByte, and a com-plete LUT at 4026 x 8 bit is 4 kByte, programming can’t take place in a one block write step because the size of an LUT is larger than GPDATA_BUFFER. Therefore input must be handled in several steps.The flow diagram below shows the sequence required to load data into the camera.
Figure 31: Loading an LUT
Note Configuration
• To configure this feature in an advanced register: See Table 89: Advanced register: LUT on page 187.
• For information on GPDATA_BUFFER: See Chapter GPDATA_BUFFER on page 201.
Query limits from register:
LUT_INFO and GPDATA_INFO
Set EnableMemWR to true (1)
Set AddrOffset to 0
Write n databytes in
GPDATA_BUFFER
Offset is increased in camera after n bytes are written
Check EnableMemWR for
no change
Repeat steps until all data is written
Set EnableMemWR to false (0)
Description of the data path
OSCAR Technical Manual V2.4.0
74
Shading correction
Shading correction is used to compensate for non-homogeneities caused by lighting or optical characteristics within specified ranges.
To correct a frame, a multiplier from 1...2 is calculated for each pixel in 1/256 steps. This allows for shading to be compensated by up to 50%.
Besides generating shading data off-line and downloading it to the camera, the camera allows correction data to be generated automatically in the cam-era itself.
The following pictures describe the process of automatic generation of cor-rection data. The line profiles were created using MVTEC's ActivVision Tools.
On the left you see the source image with non-uniform illumination. The graph on the right clearly shows the brightness level falling off to the right.
By defocusing the lens, high-frequency image data are removed from the source image, therefore its not included in the shading image.
Note • Shading correction does not support the mirror func-tion.
• If you use shading correction, don’t change the mirror function.
Figure 32: Shading correction: Source image with non-uniform illumination
Description of the data path
OSCAR Technical Manual V2.4.0
75
Automatic generation of correction data
Requirements
Shading correction compensates for non-homogeneities by giving all pixels the same gray value as the brightest pixel. This means that only the back-ground must be visible and the brightest pixel has a gray value of less than 255 when automatic generation of shading data is started.
It may be necessary to use a neutral white reference, e.g. a piece of paper instead of the real image.
Algorithm
After the start of automatic generation, the camera pulls in the number of frames set in the GRAB_COUNT register. Recommended values are 4, 8 or 16. An arithmetic mean value is calculated from them (to reduce noise).
After this, a search is made for the brightest pixel in the mean value frame. The brightest pixel(s) remain unchanged. A factor is then calculated for each pixel to be multiplied by, giving it the gray value of the brightest pixel.
All of these multipliers are saved in a shading reference image. The time required for this process depends on the number of frames to be calculated and on the resolution of the image.
Correction alone can compensate for shading by up to 50% and relies on 12 bit pixel data to avoid the generation of missing codes.
Thus the output after the shading correction has potentially 11-bit accuracy.
How to proceed:
Figure 33: Automatic generation of a shading image
Set GrabCount to # of desired frames
Set BuildImage Flag to true
Poll SHGD_Control Register until Busy and
BuildImage Flag are resetted
Description of the data path
OSCAR Technical Manual V2.4.0
76
The following pictures illustrate the sequence of commands for generating the shading image.
The correction sequence controlled (e.g. via Directcontrol) uses the average of 16 frames (10H) to calculate the correction frame.
The top picture shows the input image (with lens out of focus). The bottom picture shows the shading corrected output image (unfocused lens).
Note Configuration
To configure this feature in an advanced register: See Table 90: Advanced register: Shading on page 188.
Note The SHDG_CTRL register should not be queried at very short intervals. This is because each query delays the generation of the shading image. An optimal interval time is 500 ms.
Note • The maximum value of GRAB_COUNT depends on the type of camera and the number of frame buffers that exist. GRAB_COUNT is corrected to the power of two automatically.
Note • The calculation of shading data is always carried out at the current resolution setting. If the AOI is later larger than the window in which correction data was calcu-lated, none of the pixels lying outside are corrected.
• For Format_7 mode, it is advisable to generate the shading image in the largest displayable frame format. This ensures that any smaller AOIs are completely cov-ered by the shading correction.
• The automatic generation of shading data can also be enabled when image capture is already running. The camera then pauses the running image capture for the time needed for generation and resumes after genera-tion is completed.
• Shading correction can be combined with the image mirror, binning and gamma functionality.
• Changing binning modes involves the generation of new shading reference images due to a change in the image size.
Description of the data path
OSCAR Technical Manual V2.4.0
77
After the lens has been focused again, the image below will be seen, but now with a considerably more uniform gradient. This is also made apparent in the graph on the right.
Figure 34: Generation of shading image
Description of the data path
OSCAR Technical Manual V2.4.0
78
The shading reference image can be output for permanent storage purposes on a host system.
It can be further uploaded into the camera, so that the shading procedure must not be repeated after power down of the camera.
Figure 35: Example of shaded image
Description of the data path
OSCAR Technical Manual V2.4.0
79
What is the real size of the shading image (MaxImageSize)?The register 0xF1000258 SHDG_INFO (MaxImageSize) delivers the sensor size but not the size of the shading image buffer.
Therefore: If you use this reported (but wrong) MaxImageSize then:• A shading image which is too small will be uploaded/downloaded.• The shading correction will only be applied on the first field.• In Format_7 there will be a row-wise image error
To avoid using a wrong MaxImageSize read the following notes:
The camera’s internal buffer for the shading image is greater than the sensor image. Therefore the buffer is divided in N sections with:
After each field there is a gap so you can see where each field ends and where the next field begins:
Field 1 MaxImageSize/Fields
BufferSize
Gap 1
:
:
Field n
Gap n
n 1...N=N: number of fields per frame
Description of the data path
OSCAR Technical Manual V2.4.0
80
For uploading/downloading a shading image the last Gap n can be ignored. The size of a field is calculated from the MaxImageSize which is theoretically camera dependent (MaxImageSize < BufferSize).
This leads to the following formula:
Camera model N: number of fieldsper frame
BufferSize
Oscar F-320C 2 620000h
Oscar F-510C 2 A00000h
Oscar F-810C 3 FC0000h
Table 27: Number of fields and BufferSize
Formula 1: MaxImageSize
MaxImageSize N 1–( ) BufferSize× MaxImageSize+N
----------------------------------------------------------------------------------------⎝ ⎠⎛ ⎞=
Description of the data path
OSCAR Technical Manual V2.4.0
81
Loading a shading image out of the cameraGPDATA_BUFFER is used to load a shading image out of the camera. Due to the size of a shading image being larger than GPDATA_BUFFER, output must be handled in several steps:
Figure 36: Uploading shading image to host
Note Configuration
• To configure this feature in an advanced register: See Table 90: Advanced register: Shading on page 188.
• For information on GPDATA_BUFFER: See Chapter GPDATA_BUFFER on page 201.
Query limits from register:
SHDG_INFO and GPDATA_INFO
Set EnableMemRD to true (1)
Set AddrOffset to 0
Set EnableMemRD to false (0)
Read n databytes of
GPDATA_BUFFER
Offset is increasedin camera after nbytes are written
Check EnableMemRD for
no change
Repeat steps until all data is read
Description of the data path
OSCAR Technical Manual V2.4.0
82
Loading a shading image into the cameraGPDATA_BUFFER is used to load a shading image into the camera. Because the size of a shading image is larger than GPDATA_BUFFER, input must be handled in several steps:
It is recommended that block writes are used to write a block of n bytes with one command into the GPDATA_BUFFER. With firmware 3.04 it is possible to write quadlets directly into the buffer, but this takes much more time.
Figure 37: Loading the shading reference image
Note Configuration
• To configure this feature in an advanced register: See Table 90: Advanced register: Shading on page 188.
• For information on GPDATA_BUFFER: See Chapter GPDATA_BUFFER on page 201.
Query limits from register:
SHDG_INFO and GPDATA_INFO
Set EnableMemWR to true (1)
Set AddrOffset to 0
Write n databytes in
GPDATA_BUFFER
Offset is increasedin camera after nbytes are written
Check EnableMemWR for
no change
Repeat steps until all data is read
Set EnableMemWR to false (0)
Description of the data path
OSCAR Technical Manual V2.4.0
83
Horizontal mirror function
All Oscar cameras are equipped with an electronic mirror function, which mirrors pixels from the left side of the image to the right side and vice versa.
The mirror is centered to the current FOV center and can be combined with all image manipulation functions, like binning, shading and DSNU.
This function is especially useful when the camera is looking at objects with the help of a mirror or in certain microscopy applications.
Note Configuration
To configure this feature in an advanced register: See Table 99: Advanced register: Mirror on page 196.
Note The use of the mirror function with color cameras and image output in RAW format has implications on the BAYER-ordering of the colors.
Figure 38: Mirror and Bayer order
Note During switchover one image may be temporarily corrupted.
Mirror OFF: R-G-G-B (all Oscar cameras) Mirror ON: G-R-B-G (all Oscar cameras)
Description of the data path
OSCAR Technical Manual V2.4.0
84
Binning (only Oscar F-510C)
2 x BinningDefinition Binning is the process of combining neighboring pixels while being read out
from the CCD chip.
Binning is used primarily for 3 reasons:• a reduction in the number of pixels and thus the amount of data while
retaining the original image area angle• an increase in the frame rate (vertical binning and full binning only)• a brighter image, also resulting in an improvement in the signal-to-
noise ratio of the image
Signal-to-noise ratio (SNR) and signal-to-noise separation specify the quality of a signal with regard to its reproduction of intensities. The value signifies how high the ratio of noise is in regard to the maximum achievable signal intensity.
The higher this value, the better the signal quality. The unit of measurement used is generally known as the decibel (dB), a logarithmic power level. 6 dB is the signal level at approximately a factor of 2.
However, the advantages of increasing signal quality are accompanied by a reduction in resolution.
Only Format_7 Binning is possible only in video Format_7. The type of binning used depends on the video mode.
Types In general, we distinguish between the following types of binning(H=horizontal, V=vertical):• 2 x H-binning• 2 x V-binning
Note Only Oscar F-510C has the binning feature.
Note Changing binning modes involves the generation of new shading reference images due to a change in the image size.
Description of the data path
OSCAR Technical Manual V2.4.0
85
Vertical binningVertical binning increases the light sensitivity of the camera by a factor of two by adding together the values of two adjoining vertical pixels output as a single pixel. At the same time this normally improves signal-to-noise sep-aration by about 3 dB.
This reduces vertical resolution. The new resolution is approximately 1/2 of the original resolution.
Format_7 Mode_6 By default use Format_7 Mode_6 for 2 x vertical binning.
This reduces vertical resolution, depending on the model.
Figure 39: 2 x vertical binning
Note Vertical resolution is reduced, but signal-to noise ratio (SNR) is increased by about 3 (2 x binning).
Note If vertical binning is activated the image may appear to be over-exposed and may require correction.
Note The image appears vertically compressed in this mode and no longer exhibits a true aspect ratio.
2 x vertical binning
Description of the data path
OSCAR Technical Manual V2.4.0
86
Horizontal binningDefinition In horizontal binning adjacent horizontal pixels in a line are combined in
pairs.
This means that in horizontal binning the light sensitivity of the camera is also increased by a factor of two (6 dB). Signal-to-noise separation improves by approx. 3 dB.
This reduces horizontal resolution. The new resolution is approximately 1/2 of the original resolution.
Format_7 Mode_5 By default use Format_7 Mode_5 for 2 x horizontal binning.
Figure 40: 2 x horizontal binning
Note The image appears horizontally compressed in this mode and does no longer show true aspect ratio.
If horizontal binning is activated the image may appear to be over-exposed and must eventually be corrected.
2 x horizontal binning
Description of the data path
OSCAR Technical Manual V2.4.0
87
2 x full binningIf horizontal and vertical binning are combined, every 4 pixels are consoli-dated into a single pixel. At first two horizontal pixels are put together and then combined vertically.
Light sensitivity This increases light sensitivity by a total of a factor of 4 and at the same time signal-to-noise separation is improved by about 6 dB.
Resolution This reduces horizontal and vertical resolution. The new resolution is approx-imately 1/4 of the original resolution.
Format_7 Mode_7 By default use Format_7 Mode_7 for 2 x full binning.
Figure 41: 2 x full binning
2 x full binning
Description of the data path
OSCAR Technical Manual V2.4.0
88
Sub-sampling
What is sub-sampling?Definition Sub-sampling is the process of skipping neighboring pixels (with the same
color) while being read out from the CCD chip.
Which Oscar models have sub-sampling?All Oscar models have this feature.
Description of sub-samplingSub-sampling is used primarily for the following reasons:• A reduction in the number of pixels and thus the amount of data while
retaining the original image area angle• Switch the sensor to progressive mode rather than frame readout mode.• Increase in the frame rate.
The sub-sampling mode of Oscar F-320C and Oscar F-810C is always H+V sub-sampling mode. Oscar F-510C offers two additional special F_7 modes, with horizontal full resolution, but vertically read out progressive (thus sub-sam-pled). This is advantageous for applications relying on highest horizontal resolution.
Use progressive modes to activate sub-sampling. The principal sub-sampling pattern is shown below. Please note that various sensors skip more than two rows in the sub-sampling mode. This is detailed in Chapter Read out modes of the sensor on page 53.
Description of the data path
OSCAR Technical Manual V2.4.0
89
High SNR mode (High Signal Noise Ratio)To configure this feature in an advanced register: See Table 101: Advanced register: High Signal Noise Ratio (HSNR) on page 197.
In this mode the camera grabs and averages a set number of images and out-puts one image with the same bit depth. This means that the camera will out-put an 8 bit averaged image when an 8-bit image format is selected.
Because of the fact that normally uncorrelated (photon-, amplifier-) noise dominates over correlated noise (fixed pattern noise), adding two images will double (6 dB) the gray levels but only increase the noise levels by (3 dB).
This enhances both the dynamic range as well as the signal to noise ratio.
Consequently adding 256 8-bit images will lead to a potential signal-to-noise enhancement of 24 dB.
Figure 42: 2 out of 4 H+V sub-sampling (color)
Note Changing sub-sampling modes involves the generation of new shading reference images due to a change in the image size.
Note • The averaged image is output at a lower frame rate being exactly the fraction: fps/number of images.
• The camera must be in idle before turning this feature on.
• The potential SNR enhancement may be lower when using more than 8-bit original bit depth.
• Select 16-bit image format in order to take advantage of the full potential SNR and DNR (DyNamic Range) enhancements.
2 out of 4 H+V sub-sampling
2
Description of the data path
OSCAR Technical Manual V2.4.0
90
Sharpness
All Oscar models are equipped with a two-step sharpness control, applying a discreet horizontal high pass in the green channel as shown in the next three line profiles.
Color interpolation
The color sensors capture the color information via so called primary color (R-G-B) filters placed over the individual pixels in a BAYER mosaic layout. An effective Bayer RGB color interpolation already takes place in all Oscar cameras. Before converting to the YUV format, color correction is done after BAYER demosaicing.
Color processing can be bypassed by using the so called RAW image transfer.
RAW mode is primarily used to• save bandwidth on the IEEE 1394 bus• achieve higher frame rates• use different BAYER demosaicing algorithms on the PC
Figure 43: Sharpness: left: 0, middle: 1, right: 2
Note Configuration
To configure this feature in feature control register: See Table 77: Feature control register on page 169.
Description of the data path
OSCAR Technical Manual V2.4.0
91
RAW mode is accessible via Color_Mode Mono8, RAW8 and via Format_7.
Color interpolation (BAYER demosaicing)In color interpolation, a red, green or blue value is determined for each pixel. Three lines are needed for this interpolation:
Note If the PC does not perform BAYER to RGB post-processing the b/w image will be superimposed with a checkerboard pattern.
Figure 44: Bayer demosaicing (interpolation)
Formula 2: Bayer demosaicing interpolation formula
P1redR1 R3 R11 R13+ + +
4---------------------------------------------------=
P1greenG2 G6 G8 G12+ + +
4------------------------------------------------=
P1blue B7=
P2redR3 R13+
2----------------------=
P2greenG4 2 G8× G12+ +
4--------------------------------------------=
P2blueB7 B9+
2-------------------=
Description of the data path
OSCAR Technical Manual V2.4.0
92
Color correction
Why color correction?
The spectral response of a CCD is different of those of an output device or the human eye. This is the reason for the fact that perfect color reproduction is not possible. In each Oscar camera there is a factory setting for the color correction coefficients, see Chapter GretagMacbeth ColorChecker on page 92.
Color correction is needed to eliminate the overlap in the color channels. This overlap is caused by the fact that:• Blue light: is seen by the red and green pixels on the CCD• Red light: is seen by the blue and green pixels on the CCD• Green light: is seen by the red and blue pixels on the CCD
The color correction matrix subtracts out this overlap.
Color correction in AVT cameras
In AVT cameras the color correction is realized as an additional step in the process from the sensor data to color output.
Color correction is used to harmonize colors for the human eye. With other AVT (color) cameras so far, you had the opportunity to use it or to switch it off.
Color correction: formula
Color correction is performed on all color CCD models before YUV conversion and mapped via a matrix as follows.
GretagMacbeth ColorChecker
Sensor specific coefficients Cxy are scientifically generated to ensure that GretagMacbeth™ ColorChecker® colors are displayed with highest color fidel-ity and color balance.
Formula 3: Color correction
Note Color correction is deactivated in Mono8 or Mono16 mode (RAW image transport).
red* Crr red× Cgr green× Cbr blue×+ +=
green* Crg red× Cgg green× Cbg blue×+ +=
blue* Crb red× Cgb green× Cbb blue×+ +=
Description of the data path
OSCAR Technical Manual V2.4.0
93
Color correction can also be switched off in YUV mode with the help of the following register:
Color conversion (RGB YUV)
The conversion from RGB to YUV is made using the following formulae:
Hue and Saturation
Oscar models are equipped with hue and saturation registers.
Hue and saturation are terms best understood with the homonymous HIS (Hue Intensity Saturation) color model.
The hue register at offset 810h allows to change the color of objects by +/- 40 steps (+/- 10°) from the nominal perception without changing white balance. Use this setting to manipulate the color appearance after having done white balance.
The saturation register at offset 814h allows changing the intensity of the colors by +/-100%.
Register Name Description
0xF10003A0 COLOR_CORR Write: 02000000h to switch color correction OFF
Write: 00000000h to switch color correction ON (default)
Table 28: Color correction switch off in YUV mode
Formula 4: RGB to YUV conversion
Note • As mentioned above: Color processing can be bypassed by using the so-called RAW image transfer.
• RGB YUV conversion can be bypassed by using RGB8 format and mode. This is advantageous from the edge color definition but needs more bandwidth (300% instead of 200% relative to b/w or RAW consumption) for the transmission, so that the maximal frame fre-quency will drop.
Y 0.3 R× 0.59 G× 0.11 B×+ +=U -0.169 R× 0.33 G×– 0.498 B× 128+ +=V 0.498 R× 0.420 G×– 0.082 B×– 128+=
Description of the data path
OSCAR Technical Manual V2.4.0
94
This means a setting of zero changes the image to black and white and a set-ting of 511 doubles the color intensity compared to the nominal one at 256.
Consider hue changes as a change in the angle of the vector, saturation a change in the length of the vector S, and all starting from the intensity coor-dinate (vector from black to white).
The following picture illustrates the transformation.
Note Configuration
To configure this feature in feature control register: See Table 77: Feature control register on page 169.
Figure 45: Hue and saturation explanation
Note This transformation is not accessible from outside.
Description of the data path
OSCAR Technical Manual V2.4.0
95
Serial interface
All Oscar cameras are equipped with the SIO (serial input/output) feature as described in IIDC V1.31. This means that the Oscar's serial interface which is used for firmware upgrades can also be used as a general RS232 interface.
Data written to a specific address in the IEEE 1394 address range will be sent through the serial interface. Incoming serial interface data is put into a cam-era buffer and can be polled from here via simple read commands. Controlling registers enable the settings of baud rates and the check of buffer sizes and serial interface errors.
Base address for the function is: F0F02100h.
Note • Hardware handshaking is not supported.• Typical PC hardware does not usually support
230400 bps or more.
Description of the data path
OSCAR Technical Manual V2.4.0
96
To configure this feature in access control register (CSR):
Offset Name Field Bit Description
000h SERIAL_MODE_REG Baud_Rate [0..7] Baud rate settingWR: Set baud rateRD: Read baud rate0: 300 bps1: 600 bps2: 1200 bps 3: 2400 bps 4: 4800 bps 5: 9600 bps 6: 19200 bps7: 38400 bps8: 57600 bps9: 115200 bps10: 230400 bpsOther values reserved
Char_Length [8..15] Character length settingWR: Set data length (7 or 8 bit)RD: Get data length7: 7 bit8: 8 bitOther values reserved
Parity [16..17] Parity settingWR: Set parityRD: Get parity setting0: None1: Odd2: Even
Stop_Bit [18..19] Stop bitWR: Set stop bitRD: Get stop bit setting0: 11: 1.52: 2
--- [20..23] Reserved
Buffer_Size_Inq [24..31] Buffer Size (RD only)This field indicates the maximum size of receive/transmit data bufferIf this field is 1, Buffer_Status_Control and SIO_Data_Reg. Char 1-3 should be ignored.
Table 29: Serial input/output control and status register (SIO CSR)
Description of the data path
OSCAR Technical Manual V2.4.0
97
0004h SERIAL_CONTROL_REG RE [0] Receive enableRD: Current statusWR:0: Disable1: Enable
TE [1] Transmit enableRD: Current statusWR:0: disable1: Enable
--- [2..7] Reserved
SERIAL_STATUS_REG TDRD [8] Transmit data buffer readyRead only0: not ready1: ready
--- [9] Reserved
RDRD [10] Receive data buffer readyRead only0: not ready1: ready
--- [11] Reserved
ORER [12] Receive data buffer overrun errorRead: current statusWR:0: no error (to clear status)1: Ignored
FER [13] Receive data framing errorRead: current statusWR:0: no error (to clear status)1: Ignored
PER [14] Receive data parity errorRead: current statusWR:0: no error (to clear status)1: Ignored
--- [15..31] Reserved
Offset Name Field Bit Description
Table 29: Serial input/output control and status register (SIO CSR)
Description of the data path
OSCAR Technical Manual V2.4.0
98
008h RECEIVE_BUFFER_STATUS_CONTRL
RBUF_ST [0..7] SIO receive buffer statusRD: Number of bytes pending in receive bufferWR: Ignored
RBUF_CNT [8..15] SIO receive buffer controlRD: Number of bytes to be read from the receive FIFOWR: Number of bytes left for readout from the receive FIFO
--- [16..31] Reserved
00Ch TRANSMIT_BUFFER_STATUS_CONTRL
TBUF_ST [0..7] SIO output buffer statusRD: Space left in TX bufferWR: Ignored
TBUF_CNT [8..15] SIO output buffer controlRD: Number of bytes written to transmit FIFOWR: Number of bytes to transmit
--- [16..31] Reserved
010h..0FFh
--- Reserved
100h SIO_DATA_REGISTER CHAR_0 [0..7] Character_0RD: Read character from receive bufferWR: Write character to transmit buffer
SIO_DATA_REGISTER CHAR_1 [8..15] Character_1RD: Read character from receive buffer+1WR: Write character to transmit buffer+1
SIO_DATA_REGISTER CHAR_2 [16..23] Character_2RD: Read character from receive buffer+2WR: Write character to transmit buffer+2
SIO_DATA_REGISTER CHAR_3 [24..31] Character_3RD: Read character from receive buffer+3WR: Write character to transmit buffer+3
Offset Name Field Bit Description
Table 29: Serial input/output control and status register (SIO CSR)
Description of the data path
OSCAR Technical Manual V2.4.0
99
To read data:
1. Query RDRD flag (buffer ready?) and write the number of bytes the host wants to read to RBUF_CNT.
2. Read the number of bytes pending in the receive buffer RBUF_ST (more data in the buffer than the host wanted to read?) and the number of bytes left for reading from the receive FIFO in RBUF_CNT (more data the host wanted to read than were in the buffer?).
3. Read received characters from SIO_DATA_REGISTER, beginning at char 0.
4. To input more characters, repeat from step 1.
To write data:
1. Query TDRD flag (buffer ready?) and write the number of bytes to send (copied from SIO register to transmit FIFO) to TBUF_CNT.
2. Read the available data space left in TBUF_ST (if the buffer can hold more bytes than are to be transmitted) and number of bytes written to transmit buffer in TBUF_CNT (if more data is to be transmitted than fits in the buffer).
3. Write character to SIO_DATA_REGISTER, beginning at char 0.
4. To output more characters, repeat from step 1.
Note • Contact your local dealer, if you require further infor-mation or additional test programs or software.
• AVT recommends the use of Hyperterminal™ or other communication programs to test the functionality of this feature. Alternatively use SmartView to try out this feature.
Controlling image capture
OSCAR Technical Manual V2.4.0
100
Controlling image capture
Shutter modes The cameras support the SHUTTER_MODES specified in IIDC V1.3. For all mod-els this shutter is a global (field) shutter; meaning that all pixels (in the same field) are exposed to the light at the same moment and for the same time span.
Continuous mode In continuous modes the shutter is opened shortly before the vertical reset happens, thus acting in a frame-synchronous way.
External trigger Combined with an external trigger, it becomes asynchronous in the sense that it occurs whenever the external trigger occurs. Individual images are recorded when an external trigger impulse is present. This ensures that even fast moving objects can be grabbed with no image lag and with minimal image blur.
Camera I/O The external trigger is fed as a TTL signal through Pin 4 of the cameraI/O connector.
Trigger modi
Oscar cameras support IIDC conforming Trigger_Mode_0 and Trigger_Mode_1 (in progressive modes only) and special Trigger_Mode_15 (bulk trigger).
Edge mode (Trigger_Mode_0)Trigger_Mode_0 sets the shutter time according to the value set in the shut-ter (or extended shutter) register.
Trigger mode also known as Description
Trigger_Mode_0 Edge mode Sets the shutter time according to the value set in the shutter (or extended shutter) register
Trigger_Mode_1 Level mode Sets the shutter time according to the active low time of the pulse applied (or active high time in the case of an inverting input)
Trigger_Mode_15 Programmable mode Is a bulk trigger, combining one external trigger event with continuous or one-shot or multi-shot internal trigger
Table 30: Trigger modi
Controlling image capture
OSCAR Technical Manual V2.4.0
101
Level mode (Trigger_Mode_1)Trigger_Mode_1 sets the shutter time in the progressive modes according to the active low time of the pulse applied (or active high time in the case of an inverting input).
Figure 46: Trigger_Mode_0 and 1
Shutter register value
External Trigger input, after inverting opto coupler
Integration Time
External Trigger input,
after inv. Opto.
External Trigger input, as applied at input pin, trigger falling edge
External Trigger input, as applied at input pin
Controlling image capture
OSCAR Technical Manual V2.4.0
102
Bulk trigger (Trigger_Mode_15)Trigger_Mode_15 is a bulk trigger, combining one external trigger event with continuous or one-shot or multi-shot internal trigger.
It is an extension of the IIDC trigger modes. One external trigger event can be used to trigger a multitude of internal image intakes.
This is especially useful for:• Grabbing exactly one image based on the first external trigger.• Filling the camera's internal image buffer with one external trigger with-
out overriding images.• Grabbing an unlimited number of images after one external trigger (sur-
veillance)
The figure below illustrates this mode.
Figure 47: Trigger_Mode_15
External Trigger input, after inverting optocoupler
N x image; N: continuous, one_shot, multi_shot
Controlling image capture
OSCAR Technical Manual V2.4.0
103
The functionality is controlled via bit [6] and bitgroup [12-15] of the IIDC register:
Register Name Field Bit Description
0xF0F00830 TRIGGER_MODE Presence_Inq [0] Presence of this feature:0: N/A1: Available
Abs_Control [1] Absolute value controlO: Control with value in the Value field 1: Control with value in the Absolute value CSRIf this bit = 1 the value in the value field has to be ignored.
--- [2..5] Reserved
ON_OFF [6] Write: ON or OFF this featureRead: read a status0: OFF1: ONIf this bit = 0, other fields will be read only.
Trigger_Polarity [7] Select trigger polarity(Except for software trigger)
If Polarity_Inq is 1:Write to change polarity of the trigger input.Read to get polarity of the trigger input.
If Polarity_Inq is 0:Read only.0: Low active input1: High active input
Trigger_Source [8..10] Select trigger source
Set trigger source ID from trigger source ID_Inq.
Trigger_Value [11] Trigger input raw signal valueread only
0: Low1: High
Trigger_Mode [12..15] Trigger_Mode
(Trigger_Mode_0..15)
--- [16..19] Reserved
Parameter [20..31] Parameter for trigger function, if required (optional)
Table 31: Trigger_Mode_15 (Bulk trigger)
Controlling image capture
OSCAR Technical Manual V2.4.0
104
The screenshots below illustrate the use of Trigger_Mode_15 on a register level:• The first line switches continuous mode off, leaving viewer in listen
mode.• The second line prepares 830h register for external trigger and
Mode_15.
Left = continuous Middle = one-shot Right = multi-shot
Line #3 switches camera back to continuous mode. Only one image is grabbed precisely with the first external trigger.
To repeat rewrite line three.
Line #3 toggles one-shot bit [0] of the one-shot register 61C so that only one image is grabbed, based on the first external trig-ger.
To repeat rewrite line three.
Line #3 toggles multi-shot bit [1] of the one-shot register 61C so that Ah images are grabbed, starting with the first external trigger.
To repeat rewrite line three.
Table 32: Description: using Trigger_Mode_15: continuous, one-shot, multi-shot
Figure 48: Using Trigger_Mode_15: Continuous, one-shot, multi-shot
Note Shutter for the images is controlled by shutter register.
Controlling image capture
OSCAR Technical Manual V2.4.0
105
Trigger delayAs already mentioned earlier, the cameras feature various ways to delay image capture based on external trigger.
With IIDC V1.31 there is a standard CSR at Register F0F00534/834h to control a delay up to FFFh x time base value.
The following table explains the inquiry register and the meaning of the var-ious bits.
Register Name Field Bit Description
0xF0F00534 TRIGGER_DLY_INQUIRY Presence_Inq [0] Indicates presence of this feature (read only)
Abs_Control_Inq [1] Capability of control with absolute value
--- [2] Reserved
One_Push_Inq [3] One-push auto mode (controlled automatically by the camera once)
Readout_Inq [4] Capability of reading out the value of this feature
ON_OFF [5] Capability of switching this feature ON and OFF
Auto_Inq [6] Auto mode (controlled automati-cally by the camera)
Manual_Inq [7] Manual mode (controlled by user)
Min_Value [8..19] Minimum value for this feature
Max_Value [20..31] Maximum value for this feature
Table 33: Trigger delay inquiry register
Controlling image capture
OSCAR Technical Manual V2.4.0
106
In addition, the cameras have an advanced register which allows even more precise delay of image capture after receiving a hardware trigger.
Trigger delay advanced register
Name Field Bit Description
0xF0F00834 TRIGGER_DELAY Presence_Inq [0] Presence of this feature:0: N/A1: Available
Abs_Control [1] Absolute value controlO: Control with value in the Value field1: Control with value in the Absolute value CSRIf this bit = 1, the value in the Value field has to be ignored
--- [2..5] Reserved
ON_OFF [6] Write: ON or OFF this featureRead: read a status0: OFF1: ONIf this bit = 0, other fields will be read only.
--- [7..19] Reserved
Value [20..31] Value
If you write the value in OFF mode, this field will be ignored.
If ReadOut capability is not available, then the read value will have no mean-ing.
Table 34: CSR: trigger delay
Register Name Field Bit Description
0xF1000400 TRIGGER_DELAY Presence_Inq [0] Indicates presence of this fea-ture (read only)
--- [1..5] Reserved
ON_OFF [6] Trigger delay on/off
--- [7..10] Reserved
DelayTime [11..31] Delay time in µs
Table 35: Advanced CSR: trigger delay
Controlling image capture
OSCAR Technical Manual V2.4.0
107
The advanced register allows the start of the integration to be delayed by max. 221 µs, which is max. 2.1 s after a trigger edge was detected.
Note • Switching trigger delay to ON also switches external Trigger_Mode_0 to ON.
• This feature works with external Trigger_Mode_0 only.
Controlling image capture
OSCAR Technical Manual V2.4.0
108
Shutter modes
Due to the frame readout (interlaced) modes of the sensors, two different shutter modes exist for the maximum resolution formats accessible via the mode register in Format_7.
The conversion from interlaced to progressive takes place in the camera's internal memory.
Split shutterThe split shutter term results from the fact that two (Oscar F-810C: three) fields are exposed and read out of the sensor one after the other.
Format_7 Mode_1 is to be used for this mode, suitable for stationary objects and when no strobe light is available. Because of the time difference between the two shutters, which is dependant on the length of the shutter, this mode is only useful for stationary objects.
Figure 49: Split shutter
External Trigger input (after inverting optocoupler)
Shutter first
field
Output first field
Single shot: Time between trigger and availablity of image
Output second field
Shutter first
field second
frame
External Trigger input
Cont. mode: Time between trigger and availablity of image
Shutter
second field
Progressive output of camera
Controlling image capture
OSCAR Technical Manual V2.4.0
109
Note • Combining split shutter with one-shot operation, it can also be seen from the above figure that the frame rate in one-shot mode is lower than that in continuous mode. This is a result of the additional delay of one or two (Oscar F-810C) fields before the progressive output of the camera can start.
• Using split shutter with a flash device connected to IntEna, you will notice that it flashes twice (or three) times per single image capture.
Controlling image capture
OSCAR Technical Manual V2.4.0
110
Joint shutterUse Format_7 Mode_0 when a strobe light flashes moving objects. The exposure for the two (three: F-810C) fields starts concurrently so that the strobe freezes odd and even lines at the same time. Field one is read out first, field two (and three) are read out after field one. Make sure that the ambient light can be neglected, otherwise it will contribute to the illumination of the scene and introduce image oddities.
The following diagram illustrates this mode.
Figure 50: Joint shutter mode
Note • Changing the shutter time only affects the first field. The second (and third) field has a constant shutter time of one (two) field length(s).
• Combining joint shutter with one-shot operation, it can also be seen from the above figure that the frame rate in one shot mode is lower than in continuous mode. This is a result of the additional delay of one or two (Oscar F-810C) fields before the progressive output of the camera can start.
External trigger input (after inverting optocoupler)
Shutter first
field
Output first field to camera
buffer
Single shot: time between trigger and availablity of image
Output second field to
camera buffer
Shutter first
field second
frame
External trigger input
Shutter second field
Cont. mode: time between trigger and availablity of image
Progressive output of camera
Controlling image capture
OSCAR Technical Manual V2.4.0
111
Exposure time (shutter) and offset
The exposure (shutter) time for continuous mode and Trigger_Mode_0 is based on the following formula:
Shutter register value x time base + offset
The register value is the value set in the corresponding IIDC register (SHUTTER [81Ch]). This number is in the range between 1 and 4095.
The shutter register value is multiplied by the time base register value (see Table 85: Advanced register: Time base on page 184). The default value here is set to 20 µs.
A camera-specific offset is also added to this value. It is different for the camera models:
Exposure time offset
Example: Oscar F-510C
100 x 20 µs + 74 µs = 2074 µs exposure time
The minimum adjustable exposure time set by register is 20 µs. The real minimum exposure time of an Oscar F-510C is then
20 µs + 74 µs = 94 µs in frame readout mode.
Camera model Offset interlaced Offset progressive
Oscar F-320C 46 µs 57 µs
Oscar F-510C 74 µs 83 µs
Oscar F-810C 98 µs 98 µs
Table 36: Camera-specific offset
Camera Register value Timebase
Oscar F-510C in interlaced (frame readout) mode
100 20 µs
Table 37: Register value and time base for Oscar F-510C
Note Generally all Oscar cameras enable certain image settings to be modified on the fly, e.g. gain and shutter can be changed by the host computer by writing into the gain and shutter registers even during camera operation. An uncertainty of one or two images remains, as the host is unaware of (espe-cially with external trigger) when the next image will arrive.
Controlling image capture
OSCAR Technical Manual V2.4.0
112
Extended shutterThe exposure time for long-term integration of up to 67 seconds can be extended via the advanced register: EXTENDED_SHUTTER
The longest exposure time, 3FFFFFFh, corresponds to 67.11 sec.
Register Name Field Bit Description
0xF100020C EXTD_SHUTTER Presence_Inq [0] Indicates presence of this feature (read only)
--- [1.. 5] Reserved
ExpTime [6..31] Exposure time in µs
Table 38: Advanced register: extended shutter
Note • Exposure times entered via the 81Ch register are mir-rored in the extended register, but not vice versa.
• Longer integration times not only increase sensitivity, but also may increase some unwanted effects, such as noise and pixel-to-pixel non-uniformity. Depending on the application, these effects may limit the longest usable integration time.
• Changes in this register have immediate effect, even when the camera is transmitting.
• Extended shutter becomes inactive after writing to a format/mode/frame rate register.
Controlling image capture
OSCAR Technical Manual V2.4.0
113
One-shot
Oscar cameras can record an image by setting the one-shot bit in the 61Ch register. This bit is automatically cleared after the image is captured. If the camera is placed in ISO_Enable mode (see Chapter ISO_Enable / free-run on page 115), this flag is ignored.
If one-shot mode is combined with the external trigger, the one-shot com-mand is used to arm it. The following screenshot shows the sequence of com-mands needed to put the camera into this mode. It enables the camera to grab exactly one image with an external trigger edge.
If there is no trigger impulse after the camera has been armed, one-shot can be cancelled by clearing the bit.
One-shot command on the bus starting exposureThe following sections describe the time response of the camera using a sin-gle frame (one-shot) command. As set out in the IIDC specification, this is a software command that causes the camera to record and transmit a single frame.
The following values apply only when the camera is idle and ready for use. Full resolution must also be set.
Figure 51: One-shot control
Feature Value
One-shot microcontroller sync ≤ 250 µs (processing time in the microcontroller)
µC-Sync/ExSync integration start 8 µs
Table 39: Values for one-shot
Controlling image capture
OSCAR Technical Manual V2.4.0
114
Microcontroller sync is an internal signal. It is generated by the microcon-troller to initiate a trigger. This can either be a direct trigger or a release for ExSync, if the camera is externally triggered.
End of exposure to first packet on the busAfter the exposure, the CCD sensor is read out; some data is written into the FRAME_BUFFER before being transmitted to the bus.
The time from the end of exposure to the start of transport on the bus is:
500 µs ± 62.5 µs
This time jitters with the cycle time of the bus (125 µs).
Figure 52: Data flow and timing after end of exposure
One-shot command
μC ExSync
Exp
osur
e
Integration start
Timebase reg. X
Shutter reg.
Offset
Processing delay
< 250 μs
= 8 μs
Interlaced/progressiveOscar F-320: 46 / 57 µs Oscar F-510: 74 / 83 µs Oscar F-810: 98 / 98 µs
timeb
ase
x sh
utte
r + o
ffset
= e
xpos
ure
time
First packet on bus= 500 μs+/-62.5 μs
Controlling image capture
OSCAR Technical Manual V2.4.0
115
Multi-shot
Setting multi-shot and entering a quantity of images in Count_Number in the 61Ch register enables the camera to record a specified number of images.
The number is indicated in bits 16 to 31. If the camera is put into ISO_Enable mode (see Chapter ISO_Enable / free-run on page 115), this flag is ignored and deleted automatically once all the images have been recorded.
If multi-shot mode is activated and the images have not yet all been cap-tured, it can be cancelled by resetting the flag. The same result can be achieved by setting the number of images to 0.
Multi-shot can also be combined with the external trigger in order to grab a certain number of images based on an external trigger. This is especially helpful in combination with the so-called deferred mode to limit the number of grabbed images to the FIFO size.
ISO_Enable / free-run
Setting the MSB (bit 0) in the 614h register (ISO_ENA) puts the camera into ISO_Enable mode or Continuous_Shot (free-run). The camera captures an infinite series of images. This operation can be quit by deleting the 0 bit.
Asynchronous broadcast
The camera accepts asynchronous broadcasts. This involves asynchronous write requests that use node number 63 as the target node with no acknowledge.
This makes it possible for all cameras on a bus to be triggered by software simultaneously - e.g. by broadcasting a one-shot. All cameras receive the one-shot command in the same IEEE 1394 bus cycle. This creates uncertainty for all cameras in the range of 125 µs.
Inter-camera latency is described in Chapter Jitter at start of exposure on page 116.
Controlling image capture
OSCAR Technical Manual V2.4.0
116
The following screenshot shows an example of broadcast commands sent with the Firedemo example of FirePackage (version 1V51 or newer):
• Line 1 shows the broadcast command, which stops all cameras con-nected to the same IEEE 1394 bus. It is generated by holding the Shift key down while clicking on Write.
• Line 2 generates a broadcast one-shot in the same way, which forces all connected cameras to simultaneously grab one image.
Jitter at start of exposure
The following chapter discusses the latency time which exists for all Oscar cameras when either a hardware or software trigger is generated, until the actual image exposure starts.
Owing to the well-known fact that an Interline Transfer CCD sensor has both a light sensitive area and a separate storage area, it is common to interleave image exposure of a new frame and output that of the previous one. It makes continuous image flow possible, even with an external trigger.
The uncertain time delay before the start of exposure depends on the state of the sensor. A distinction is made as follows:
FVal is active the sensor is reading out, the camera is busy
In this case the camera must not change horizontal timing so that the trigger event is synchronized with the current horizontal clock. This introduces a maximum uncertainty which is equivalent to the line time. The line time depends on the sensor used and therefore can vary from model to model.
FVal is inactive the sensor is ready, the camera is idle
Figure 53: Broadcast one-shot
Controlling image capture
OSCAR Technical Manual V2.4.0
117
In this case the camera can resynchronize the horizontal clock to the new trigger event, leaving only a very short uncertainty time of the master clock period.
Frame memory and deferred image transport
An image is normally captured and transported in consecutive steps. The image is taken, read out from the sensor, digitized and sent over the 1394 bus.
As all Oscar cameras are equipped with built-in image memory, this order of events can be paused or delayed by using the deferred image transport fea-ture.
Oscar cameras, by standard, are equipped with 32 MB RAM (Oscar F-810C: 64 MB RAM). As an option, the memory can be extended at the factory to a maximum of 256 MB.
The table below shows how many frames can be stored by each model. The memory is arranged in a FIFO (First in First out) manner. This makes address-ing for individual images unnecessary.
Deferred image transport is especially useful for multi-camera applications where a multitude of cameras grab a certain number of images without hav-ing to take available bus bandwidth, DMA- and ISO-channels into account.
Model Camera idle Camera busy
Oscar F-320C ± 3.35 µs ± 98 µs
Oscar F-510C ± 6.00 µs ± 134 µs
Oscar F-810C ± 7.85 µs ± 128 µs
Table 40: Jitter at exposure start
Note • Jitter at the beginning of an exposure has no effect on the length of exposure, i.e. it is always constant.
Model # frames (standard) # frames (256 MB)
Oscar F-320C 3 frames (32 MB) 31 frames (256 MB)
Oscar F-510C 2 frames (32 MB) 23 frames (256 MB)
Oscar F-810C 3 frames (64 MB) 15 frames (256 MB)
Table 41: FIFO memory size
Controlling image capture
OSCAR Technical Manual V2.4.0
118
Image transfer is controlled from the host computer by addressing individual cameras and reading out the desired number of images. Functionality is con-trolled by the following register:
HoldImg modeBy setting the HoldImg flag, transport of the image over the 1394 bus is stopped completely. All captured images are stored in the internal ImageFiFo. The camera reports the maximum possible number of images in the FiFoSize variable.
Register Name Field Bit Description
0xF1000260 DEFERRED_TRANS Presence_Inq [0] Indicates presence of this feature (read only)
--- [1..4] Reserved
SendImage [5] Send NumOfImages now (auto reset)
HoldImg [6] Enable/disable deferred transport mode
FastCapture [7] Enable/disable fast capture mode
--- [8..15] Reserved
FIFOSize [16..23] Size of FIFO in number of images (read only)
NumOfImages [24..31] W: Number of images to sendR: Number of images in buffer
Table 42: Advanced register: Deferred image transport
Note • Pay attention to the maximum number of images that can be stored in FIFO. If you capture more images than the number in FIFOSize, the oldest images are overwrit-ten.
• The extra SendImage flag is set to true to import the images from the camera. The camera sends the number of images that are entered in the NumOfImages parameter.
• If NumOfImages is 0 all images stored in FIFO are sent.
• If NumOfImages is not 0, the corresponding number of images is sent.
• If the HoldImg field is set to false, all images in ImageFIFO are deleted. No images are sent.
• The last image in the FiFo will be corrupted, when simultaneously used as input buffer while being read out. Read out one image less than maximum buffer size in this case.
Controlling image capture
OSCAR Technical Manual V2.4.0
119
The following screenshot shows the sequence of commands needed to work with deferred mode.
FastCaptureThis mode can be activated only in Format_7.• If FastCapture is set to false, the maximum frame rate both for image
acquisition and read out is associated with the packet size set in the BYTE_PER_PACKET register. The lower this value is, the lower the attain-able frame rate is.
• If FastCapture is set to true, all images are recorded at the highest pos-sible frame rate, i.e. the setting above does not affect the frame rate for the image intake but only the read out. This mode is ideal for applica-tions where a burst of images need to be recorded at the highest sensor speed but the output can be at a lower frame frequency to save band-width.
Figure 54: Example of controlling deferred mode
.................................Stop continuous mode of camera
.................................Check pres. of deferred mode and FiFo size (Dh= 13 fr.)
.................................Switch deferred mode on
.................................Do first One_shot
.................................Do second One_shot
.................................Check that two images are in FiFo
.................................Read out the first image of FiFo
.................................Check how many images are left in FiFo
.................................Read out the second image of FiFo
....................................Check how many images are left in FiFo
Video formats, modes and bandwidth
OSCAR Technical Manual V2.4.0
120
Video formats, modes and bandwidth
The different Oscar models support different video formats, modes and frame rates.
These formats and modes are standardized in the IIDC (formerly DCAM) spec-ification.
Resolutions in Format_0, Format_1 and Format_2, which are smaller than the generic sensor resolution, are generated symmetrically from the center of the sensor and without binning.
Different color processing modes in Format_7 are accessed via Color_Coding_ID register, as listed for Oscar F-510C.
Binning modes are only available in Format_7 for Oscar F-510C:• Format_7 Mode_5: horizontal binning (H-binning)• Format_7 Mode_6: vertical binning (V-binning)• Format_7 Mode_7: horizontal and vertical binning (H+V binning)
Note • The maximum frame rates can only be achieved with shutter settings lower than 1/framerate. This means that with default shutter time of 40 ms, a camera will not achieve frame rates higher than 25 frames/s. In order to achieve higher frame rates, please reduce the shutter time proportionally.
• The following tables assume that bus speed is 400 Mbit/s. With lower bus speeds (e.g. 200 or 100 Mbit/s) not all frame rates may be achieved.
• For information on bit/pixel and byte/pixel for each color mode see Table 92: ByteDepth on page 215.
Note H-binning means horizontal binning.
V-binning means vertical binning.
Full binning (H+V) means horizontal + vertical binning
2 x binning means: 2 neighboring pixels are combined.
• Binning increases signal-to-noise ratio (SNR), but decreases resolution.
Video formats, modes and bandwidth
OSCAR Technical Manual V2.4.0
121
Video formats: Oscar F-320C
Format Mode Resolution Color mode 60 fps
30 fps [4]
15fps
7.5 fps
3.75 fps
1.875 fps
0
0 160 x 120 YUV444
1 320 x 240 YUV422 x x x x
2 640 x 480 YUV411
3 640 x 480 YUV422
4 640 x 480 RGB8
5 640 x 480 MONO8
6 640 x 480 MONO16
Table 43: Video fixed formats Oscar F-320C (centered progressive preview mode)
Format Mode Resolution Color mode Frame rate / fps Description
7 0 2080 x 1540
Mono8 [2] 6.59
frame readout,
joint shutter
YUV411 6.59
YUV422 5.11
RGB8 3.41
Raw8 [1] 6.59
Raw16 [1] 5.11
Y8red, Y8green, Y8blue [3] 6.59
7 1 2080 x 1540
Mono8 [2] 6.59
frame readout,
split shutter
YUV411 6.59
YUV422 5.11
RGB8 3.41
Raw8 [1] 6.59
Raw16 [1] 5.11
Y8red, Y8green, Y8blue [3] 6.59
Table 44: Video Format_7 formats Oscar F-320C
Video formats, modes and bandwidth
OSCAR Technical Manual V2.4.0
122
7 2 344 x 254
Mono8 [2] 39.31 [4]
progressive preview mode
sub-sampling
YUV411 39.31 [4]
YUV422 39.31 [4]
RGB8 39.51 [4]
Raw8 [1]39.31 [4]
Raw16 [1] 39.31 [4]
Y8red, Y8green, Y8blue [3] 39.31 [4]
[1] Camera outputs RAW image which needs to be converted outside of camera.[2] Camera outputs interpolated B/W image using luma interpolation formula.[3] Camera outputs interpolated B/W image using one of the R-G-B color planes.[4] Only achievable with shutter settings that don't exceed 1/framerate.
Format Mode Resolution Color mode Frame rate / fps Description
Table 44: Video Format_7 formats Oscar F-320C
Video formats, modes and bandwidth
OSCAR Technical Manual V2.4.0
123
Video formats: Oscar F-510C
[1] Camera outputs RAW image which needs to be converted outside of camera.[2] Camera outputs interpolated B/W image using luma interpolation formula.[3] Camera outputs interpolated B/W image using one of the R-G-B color planes.[4] Only achievable with shutter settings that don't exceed 1/framerate.
Format Mode Resolution Color mode 60 fps
30 fps [4]
15fps
7.5 fps
3.75 fps
1.875 fps
1
0 800 x 600 YUV422
1 800 x 600 RGB8
2 800 x 600 MONO8 x[2] x[2]
3 1024 x 768 YUV422 x x
4 1024 x 768 RGB8 x x
5 1024 x 768 MONO8
6 800 x 600 MONO16
7 1024 x 768 MONO16
2
0 1280 x 960 YUV422 x x x
1 1280 x 960 RGB8 x x x
2 1280 x 960 MONO8 x[2] x[2] x[2]
3 1600 x 1200 YUV422
4 1600 x 1200 RGB8
5 1600 x 1200 MONO8
6 1280 x 960 MONO16
7 1600 x 1200 MONO16
Table 45: Video fixed formats Oscar F-510C (progressive)
Video formats, modes and bandwidth
OSCAR Technical Manual V2.4.0
124
Format Mode Resolution Color mode Frame rate / fps Description
7 0 2588 x 1958
Mono8 [2] 3.80
frame readout
joint shutter
YUV411 3.80
YUV422 3.23
RGB8 2.15
Raw8 [1] 3.80
Raw16 [1] 3.23
Y8red, Y8green, Y8blue [3] 3.80
7 1 2588 x 1958
Mono8 [2] 3.80
frame readout
split shutter
YUV411 3.80
YUV422 3.23
RGB8 2.15
Raw8 [1] 3.80
Raw16 [1] 3.23
Y8red, Y8green, Y8blue [3] 3.80
7 2 1288 x 978
Mono8 [2] 7.59
progressive, centered
sub-sampling
YUV411 7.58
YUV422 7.59
RGB8 7.59
Raw8 [1] 7.59
Raw16 [1] 7.59
Y8red, Y8green, Y8blue [3] 7.59
7 3 2576 x 978
Mono8 [2] 7.59
progressive scan
v-sub-sampling
YUV411 7.59
YUV422 6.50
RGB8 4.33
Raw8 [1] 7.59
Raw16 [1] 6.50
Y8red, Y8green, Y8blue [3] 7.59
Table 46: Video Format_7 formats Oscar F-510C
Video formats, modes and bandwidth
OSCAR Technical Manual V2.4.0
125
7 4 2576 x 1958
Mono8 [2] 3.87
progressive scan
V-line-doubling
YUV411 3.87
YUV422 3.25
RGB8 2.16
Raw8 [1] 3.87
Raw16 [1] 3.25
Y8red, Y8green, Y8blue [3] 3.87
7 5 1292 x 1958
Mono8 [2] 3.79
interlaced,
split shutter
2 x H-binning
YUV411 3.80
YUV422 3.80
RGB8 3.80
Raw8 [1] 3.79
Raw16 [1] 3.80
Y8red, Y8green, Y8blue [3] 3.79
7 6 2588 x 978
Mono8 [2] 6.98
interlaced,
split shutter
2 x V-binning
YUV411 6.99
YUV422 6.47
RGB8 4.31
Raw8 [1] 6.98
Raw16 [1] 6.47
Y8red, Y8green, Y8blue [3] 6.98
7 7 1292 x 978
Mono8 [2] 6.98
interlaced,
split shutter
2 x H+V binning
YUV411 6.98
YUV422 6.98
RGB8 6.99
Raw8 [1] 6.98
Raw16 [1] 6.98
Y8red, Y8green, Y8blue [3] 6.98
Format Mode Resolution Color mode Frame rate / fps Description
Table 46: Video Format_7 formats Oscar F-510C
Video formats, modes and bandwidth
OSCAR Technical Manual V2.4.0
126
The different color modes in Format_7 modes are controlled via the COLOR_CODING_ID register in combination with COLOR_CODING_INQ regis-ter.
[1] Camera outputs RAW image which needs to be converted outside of camera.[2] Camera outputs interpolated B/W image using luma interpolation formula.[3] Camera outputs interpolated B/W image using one of the R-G-B color planes.[4] Only achievable with shutter settings that don't exceed 1/framerate.
Offset Name Field Bit Notes
F0F08010h FORMAT_7_MODE_0 COLOR_CODING_ID
Coding_ID [0..7] Color coding ID from COLOR_CODING_INQ register
F0F08014h
F_7M_0 COLOR_CODING_INQ
Mono8 [0] ID=0
YUV 411 [1] ID=1
YUV 422 [2] ID=2
RGB8 [4] ID=4
RAW8 [9] ID=9
RAW16 [10] ID=10
F0F08024h
Y8red [0] ID=128
Y8green [1] ID=129
Y8blue [2] ID=130
F0F09010h F_7M_1 COLOR_CODING_ID Same for Mode_1
F0F09014h F_7M_1 COLOR_CODING_INQ Same for Mode_1
F0F0A010h F_7M_2 COLOR_CODING_ID Same for Mode_2
F0F0A014h F_7M_2 COLOR_CODING_INQ Same for Mode_2
F0F0B010h F_7M_3 COLOR_CODING_ID Same for Mode_3
F0F0B014h F_7M_3 COLOR_CODING_INQ Same for Mode_3
F0F0C010h F_7M_4 COLOR_CODING_ID Same for Mode_4
F0F0C014h F_7M_4 COLOR_CODING_INQ Same for Mode_4
Table 47: Color coding inquiry and IDs
Video formats, modes and bandwidth
OSCAR Technical Manual V2.4.0
127
Video formats: Oscar F-810C
[1] Camera outputs RAW image which needs to be converted outside of camera.[2] Camera outputs interpolated B/W image using luma interpolation formula.[3] Camera outputs interpolated B/W image using one of the R-G-B color planes.[4] Only achievable with shutter settings that don't exceed 1/framerate.
Format Mode Resolution Color mode 60 fps
30 fps [4]
15fps
7.5 fps
3.75 fps
1.875 fps
1
0 800 x 600 YUV422
1 800 x 600 RGB8
2 800 x 600 MONO8
3 1024 x 768 YUV422 x x
4 1024 x 768 RGB8 x x
5 1024 x 768 MONO8 x[2] x[2]
6 800 x 600 MONO16
7 1024 x 768 MONO16
Table 48: Fixed video formats Oscar F-810C (frame readout, centered)
Format Mode Resolution Color mode Frame rate / fps Description
7 0 3272 x 2469
Mono8 [2] 3.15
frame readout
joint shutter
YUV411 2.70
YUV422 2.03
RGB8 1.35
Raw8 [1] 3.15
Raw16 [1] 2.03
Y8red, Y8green, Y8blue [3] 3.15
7 1 3272 x 2469
Mono8 [2] 3.15
frame readout
split shutter
YUV411 2.70
YUV422 2.03
RGB8 1.35
Raw8 [2] 3.15
Raw16 [1] 2.03
Y8red, Y8green, Y8blue [3] 3.15
Table 49: Format_7 video formats Oscar F-810C
Video formats, modes and bandwidth
OSCAR Technical Manual V2.4.0
128
[1] Camera outputs RAW image which needs to be converted outside of camera.[2] Camera outputs interpolated B/W image using luma interpolation formula.[3] Camera outputs interpolated B/W image using one of the R-G-B color planes.[4] Only achievable with shutter settings that don't exceed 1/framerate.
7 2 1088 x 822
Mono8 [2] 8.86
progressive scan
sub-sampling
YUV411 8.88
YUV422 8.88
RGB8 8.88
Raw8 [1] 8.86
Raw16 [1] 8.88
Y8red, Y8green, Y8blue [3] 8.86
Format Mode Resolution Color mode Frame rate / fps Description
Table 49: Format_7 video formats Oscar F-810C
Video formats, modes and bandwidth
OSCAR Technical Manual V2.4.0
129
Area of interest (AOI)
pixels per line that the recorded image may have.
However, often only a certain section of the entire image is of interest. The amount of data to be transferred can be decreased by limiting the image to a section when reading it out from the camera. At a lower vertical resolution the sensor can be read out faster and thus the frame rate is increased.
While the size of the image read out for most other video formats and modes is fixed by the IIDC specification, thereby determining the highest possible frame rate, in Format_7 mode the user can set the upper left corner and width and height of the section (area of interest = AOI) he is interested in to determine the size and thus the highest possible frame rate.
Setting the AOI is done in the IMAGE_POSITION and IMAGE_SIZE registers.
IMAGE_POSITION and IMAGE_SIZE contain in the respective bits values for the column and line of the upper left corner and values for the width and height.
Note The setting of AOIs is supported only in video Format_7.
Note Pay attention to the increments entering in the UNIT_SIZE_INQ and UNIT_POSITION_INQ registers when con-figuring IMAGE_POSITION and IMAGE_SIZE.
Video formats, modes and bandwidth
OSCAR Technical Manual V2.4.0
130
The following table lists the various increments in pixel (px) as a function of the camera model and mode.
Figure 55: Area of Interest (AOI)
Note • The left position + width and the upper position + height may not exceed the maximum resolution of the sensor. The increments may vary from model and mode.
• The coordinates for width and height must be divisible by a factor which is depending on the camera model.
Camera Oscar F-320C Oscar F-510C Oscar F-810CF_7 Mode_0/1
Oscar F-810CF_7 Mode_2
H-Pos 2 px 2 px 2 px 2 px
V-Pos 2 px 2 px 6 px 2 px
H-Size 4 px 4 px 4 px 4 px
V-Size 2 px 2 px 3 px 2 px
Table 50: AOI increments for different camera models and Format_7 modes
Video formats, modes and bandwidth
OSCAR Technical Manual V2.4.0
131
In addition to the Area of Interest, some other parameters have an effect on the maximum frame rate:• The time for reading the image from the sensor and transporting it into
the FRAME_BUFFER• The time for transferring the image over the FireWire™ bus• The length of the exposure time.
Read the next chapter for more details.
Frame rates
An IEEE 1394 camera requires bandwidth to transport images.
The IEEE 1394a bus has very large bandwidth of at least 32 MByte/s for trans-ferring (isochronously) image data. Per cycle up to 4096 bytes (or around 1000 quadlets = 4 bytes @ 400 Mbit/s) can thus be transmitted.
Depending on the video format settings and the configured frame rate, the camera requires a certain percentage of maximum available bandwidth. Clearly the bigger the image and the higher the frame rate, there is more data to be transmitted.
The following tables indicate the volume of data in various formats and modes to be sent within one cycle (125 µs) at 400 Mbit/s of bandwidth.
The tables are divided into three formats:
They enable you to calculate the required bandwidth and to ascertain the number of cameras that can be operated independently on a bus and in which mode.
Note All bandwidth data is calculated with:
1 MByte = 1024 kByte
Format Resolution Max. video format
Format_0 up to VGA 640 x 480
Format_1 up to XGA 1024 x 768
Format_2 up to UXGA 1600 x 1200
Table 51: Overview fixed formats
Video formats, modes and bandwidth
OSCAR Technical Manual V2.4.0
132
As an example, VGA MONO8 @ 60 fps requires four lines (640 x 4 = 2560 pix-els/byte) to transmit every 125 µs: this is a consequence of the sensor's line time of about 30 µs. Therefore no data needs to be stored temporarily.
It takes 120 cycles (120 x 125 µs = 15 ms) to transmit one frame, which arrives every 16.6 ms from the camera. Again no data need to be stored tem-porarily.
Thus around 64% of the available bandwidth (at S400) is used.
Format Mode Resolution 60fps
30fps
15fps
7.5fps
3.75fps
0
0160 x 120 YUV (4:4:4)
24 bit/pixel
1/2H80p60q
1/4H40p30q
1/8H20p15q
1320 x 240 YUV (4:2:2)
16 bit/pixel
1H320p160q
1/2H160p80q
1/4H80p40q
1/8H40p20q
2640 x 480 YUV (4:1:1)
12 bit/pixel
2H1280p480q
1H640p240q
1/2H320p120q
1/4H160p60q
3640 x 480 YUV (4:2:2)
16 bit/pixel
2H1280p640q
1H640p320q
1/2H320p160q
1/4H160p80q
4640 x 480 RGB
24 bit/pixel
2H1280p960q
1H640p480q
1/2H320p240q
1/4H160p120q
5640 x 480 (MONO8)
8 bit/pixel
4H2560p640q
2H1280p320q
1H640p160q
1/2H320p80q
1/4H160p40q
6640 x 480 Y (MONO16)
16 bit/pixel
2H1280p640q
1H640p320q
1/2H320p160q
1/4H160p80q
7640 x 480 Y (MONO16)
Reserved
Table 52: Format_0
Video formats, modes and bandwidth
OSCAR Technical Manual V2.4.0
133
Format Mode Resolution Color mode 60fps
30fps
15fps
7.5fps
3.75 fps
1.875 fps
1
0 800 x 600
16 bit/pixel
YUV (4:2:2) 5/2H 2000p 1000q
5/4H 1000p 500q
5/8H 500p 250q
6/16H 250p 125q
1 800 x 600
24 bit/pixel
RGB 5/4H 1000p 750q
5/8H 500p 375q
2 800 x 600
8 bit/pixel
Y (MONO8) 5H 4000p 1000q
5/2H 2000p 500q
5/4H 1000p 250q
5/8H 500p 125q
3 1024 x 768
16 bit/pixel
YUV (4:2:2) 3/2H 1536p 768q
3/4H 768p 384q
3/8H 384p 192q
3/16H 192p 96q
4 1024 x 768
24 bit/pixel
RGB 3/4H 768p 576q
3/8H 384p 288q
3/16H 192p 144q
5 1024 x 768
8 bit/pixel
Y (MONO) 3H 3072p 768q
3/2H 1536p 384q
3/4H 768p 192q
3/8H 384p 96q
3/16H 192p 48q
6 800 x 600
16 bit/pixel
(MONO16) 5/2H 2000p 1000q
5/4H 1000p 500q
5/8H 500p 250q
5/16H 250p 125q
7 1024 x 768
16 bit/pixel
Y (MONO16) 3/2H 1536p 768q
3/4H 768p 384q
3/8H 384p 192q
3/16H 192p 96q
Table 53: Format_1
Video formats, modes and bandwidth
OSCAR Technical Manual V2.4.0
134
As already mentioned, the recommended limit for transferring isochronous image data is 1000q (quadlets) per cycle or 4096 bytes (with 400 Mbit/s of bandwidth).
The third table shows that in Format_2 Mode_2 @ 7.5 fps a camera has to send 1280 pixels or 1 line of video per cycle. The camera therefore uses 32% of available bandwidth. This allows up to three cameras with these settings to be operated independently on the same bus.
Format Mode Resolution Color Mode 60 fps
30 fps
15 fps
7.5 fps
3.75 fps
1.875 fps
2
01280 x 960
16 bit/pixel
YUV (4:2:2) 1H 1280p 640q
1/2H 640p 320q
1/4H 320p 160q
11280 x 960
24 bit/pixel
RGB 1H 1280p 960q
1/2H 640p 480q
1/4H 320p 240q
21280 x 960
8 bit/pixel
Y (MONO8) 2H 2560p 640q
1H 1280p 320q
1/2H 640p 160q
1/4H 320p 80q
31600 x 1200
16 bit/pixel
YUV (4:2:2) 5/4H 2000p 1000q
5/8H 1000p 500q
5/16H 500p 250q
41600 x 1200
24 bit/pixel
RGB 5/8H 1000p 750q
5/16 500p 375q
51600 x 1200
8 bit/pixel
Y (MONO8) 5/2H 4000p 1000q
5/4H 2000p 500q
5/8H 1000p 250q
5/16H 500p 125q
61280 x 960
16 bit/pixel
Y (MONO16) 1H 1280p 640q
1/2H 640p 320q
1/4H 320p 160q
71600 x 1200
16 bit/pixel
Y (MONO16) 5/4H 2000p 1000q
5/8H 1000p 500q
5/16H 500p 250q
Table 54: Format_2
Note • If the cameras are operated with an external trigger the maximum trigger frequency may not exceed the highest continuous frame rate, so preventing frames from being dropped or corrupted.
• IEEE 1394 adapter cards with PCILynx™ chipsets have a lower limit of 4000 bytes per cycle.
Video formats, modes and bandwidth
OSCAR Technical Manual V2.4.0
135
The frame rates in video modes 0 to 2 are specified and set fixed by IIDC V1.3.
Frame rates Format_7In video Format_7 frame rates are no longer fixed but can be varied dynam-ically by the parameters described below.
Frame rates may be further limited by bandwidth limitation from the IEEE 1394 bus.
Details are described in the next chapters:• Max. frame rate of CCD (theoretical formula)• Diagram of frame rates as function of AOI by constant width: the curves
describe RAW8, RAW12/YUV411, RAW16/YUV422, RGB8 and max. frame rate of CCD
• Table with max. frame rates as function of AOI by constant width
For the CCD models the following formula is used to calculate the highest frame rate in Format_7:
It assumes that the maximum frame rate is the inverse of the sum of all events in a CCD, which take time such as:
Frame rates may be further limited by longer shutter times and/or by band-width limitation from the IEEE 1394 bus. This is not part of the formulae below.
Details are described in the next chapter.
Note • Different values apply for the different sensors.• Frame rates may be further limited by longer shutter
times and/or bandwidth limitation from the IEEE 1394 bus.
Formula 5: Frame rate calculation
Note • The time to transfer the storage to the vertical shift register (charge transfer time)
• The time to shift out the dummy lines• The time to dump the lines outside the AOI• The time to shift out the lines of the AOI (scanning
time)
framerateIn framerateCCD1
TCh eTransarg TDummy TDump TScan+ + +-----------------------------------------------------------------------------------------------= =
Video formats, modes and bandwidth
OSCAR Technical Manual V2.4.0
136
Oscar F-320C: AOI frame ratesFrame rates differ for the progressive scan mode and the field read out (or interlaced) mode.
Oscar F-320C: progressive scan mode
For progressive scan mode (i.e. fixed formats and Format_7, Mode_2), the following formula applies:
Formula 6: Frame rate calculation progressive scan mode Oscar F-320C
AOI height Tframe / s Frame rate / fps
254 0.025 39.679
240 0.024 41.796
120 0.013 77.032
60 0.008 133.163
30 0.005 209.486
Table 55: Frame rates progressive Oscar F-320C
Figure 56: Graph of frame rates in progressive scan mode Oscar F-320C
frame rate 1TCh eTransarg TDummy TDump TScan+ + +-----------------------------------------------------------------------------------------------=
frame rate 1290µs 257 AOI_HEIGHT–( ) x 6.8µs AOI_HEIGHT 98µs×+ +-----------------------------------------------------------------------------------------------------------------------------------------------------=
Frame rate = f(AOI height)
0
20
40
60
80
100
120
140
160
180
200
220
0 20 40 60 80 100 120 140 160 180 200 220 240 260 280
AOI height / pixel
Fram
e ra
te /
fps
OF-320C Progressive (Format_7 Mode_2 and all fixed modes)
Video formats, modes and bandwidth
OSCAR Technical Manual V2.4.0
137
Oscar F-320C: interlaced mode
For interlaced mode, the following formula applies:
Formula 7: Frame rate calculation interlaced mode Oscar F-320C
AOI height Tframe / s Frame rate / fps
1540 0.152 6.6001536 0.151 6.6161200 0.121 8.2981024 0.104 9.574960 0.099 10.140600 0.066 15.201480 0.055 18.234240 0.033 30.346120 0.022 45.43560 0.017 60.468
Table 56: Frame rates interlaced mode Oscar F-320C
Figure 57: Graph of frame rates interlaced mode Oscar F-320C
frame rate 1TCh eTransarg TDummy TDump TScan+ + +-----------------------------------------------------------------------------------------------=
frame rate 1580µs 1542 AOI_HEIGHT–( ) x 6.8µs AOI_HEIGHT 98µs×+ +--------------------------------------------------------------------------------------------------------------------------------------------------------=
Frame rate = f(AOI height)
0
10
20
30
40
50
60
70
0 100 200 300 400 500 600 700 800 900 1000 1100 1200 1300 1400 1500 1600 1700
AOI height / pixel
Fram
e ra
te /
fps
OF-320C Interlaced (Format_7, Mode_0 and Mode_1)
Video formats, modes and bandwidth
OSCAR Technical Manual V2.4.0
138
Oscar F-510C: AOI frame ratesFrame rates differ for the progressive scan mode and the field read out mode (or interlaced mode).
Oscar F-510C: progressive scan mode
For progressive scan mode (i.e. fixed formats and Format_7, Mode_2), the following formula applies:
Formula 8: Frame rate calculation progressive scan mode Oscar F-510C
AOI height Tframe / s Frame rate / fps
980 0.132 7.585960 0.129 7.737960 0.129 7.737600 0.083 12.081480 0.067 14.862240 0.036 27.548120 0.021 48.058
Table 57: Frame rates progressive scan Oscar F-510C
Figure 58: Graph of frame rate in progressive scan mode Oscar F-510C
frame rate 1TCh eTransarg TDummy TDump TScan+ + +-----------------------------------------------------------------------------------------------=
frame rate 1230µs 1038 AOI_HEIGHT–( ) x 4.9µs AOI_HEIGHT 134µs×+ +-------------------------------------------------------------------------------------------------------------------------------------------------------------=
Frame rate = f(AOI height)
0
10
20
30
40
50
60
0 100 200 300 400 500 600 700 800 900 1000 110
AOI height / pixel
Fram
e ra
te /
fps
OF-510C Progressive (Format_7 Mode_2 and all fixed modes)
Video formats, modes and bandwidth
OSCAR Technical Manual V2.4.0
139
Oscar F-510C: interlaced modes
For all interlaced modes (i.e. Format_7 Mode_0 and Mode_1), the following formula applies:
Formula 9: Frame rate calculation interlaced modes Oscar F-510C
AOI height Tframe / s Frame rate / fps
1960 0.263 3.8001536 0.208 4.7981200 0.165 6.0581024 0.142 7.025960 0.134 7.458600 0.088 11.415480 0.072 13.868240 0.041 24.316
Table 58: Frame rates interlaced modes Oscar F-510C
Figure 59: Graph of frame rates interlaced mode Oscar F-510C
frame rate 1
2 233µs 987 AOI_HEIGHT2
------------------------------–⎝ ⎠⎛ ⎞ 4.9µs× AOI_HEIGHT
2------------------------------ 134µs×+ +⎝ ⎠
⎛ ⎞×--------------------------------------------------------------------------------------------------------------------------------------------------------------------=
Frame rate = f(AOI height)
0
5
10
15
20
25
30
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200
Fram
e ra
te /
fps
OF-510C Interlaced (Format_7, Mode_0 and Mode_1)
Video formats, modes and bandwidth
OSCAR Technical Manual V2.4.0
140
Oscar F-810C: AOI frame ratesFrame rates differ for the progressive scan mode and the field read out mode (interlaced mode).
Oscar F-810C: progressive scan mode
For progressive scan mode (i.e. fixed formats and Format_7, Mode_2), the following formula applies:
The table details the frame rates for representative image heights.
Formula 10: Frame rate calculation progressive scan mode Oscar F-810C
AOI height Tframe / s Frame rate / fps
822 0.112 8.907600 0.087 11.440480 0.074 13.519240 0.047 21.235120 0.034 29.716
Table 59: Frame rates progressive scan mode Oscar F-810C
Figure 60: Graph of frame rate in progressive scan mode Oscar F-810C
frame rate 1TCh eTransarg TDummy TDump TScan+ + +-----------------------------------------------------------------------------------------------=
frame rate 1276µs 1246 AO_HEIGHT–( ) x 16µs AOI_HEIGHT 128µs×+ +--------------------------------------------------------------------------------------------------------------------------------------------------------=
Frame rate = f(AOI height)
0
5
10
15
20
25
30
35
0 100 200 300 400 500 600 700 800 900
AOI height / pixel
Fram
e ra
te /
fps
OF-810C Progressive (Format_7, Mode_2 and all fixed modes)
Video formats, modes and bandwidth
OSCAR Technical Manual V2.4.0
141
Oscar F-810C: interlaced modes
For all interlaced modes (i.e. Format_7 Mode_0 and Mode_1), the following formula applies:
Formula 11: Frame rate calculation interlaced modes Oscar F-810C
AOI height Tframe / s Frame rate / fps
2470 0.317 3.1512400 0.310 3.2301536 0.213 4.6991200 0.175 5.7091024 0.155 6.433960 0.148 6.744600 0.108 9.263480 0.095 10.580240 0.068 14.784
Table 60: Frame rates interlaced modes Oscar F-810C
Figure 61: Graph of frame rate in interlaced mode Oscar F-810C
frame rate 1
3 291µs 831 AOI_HEIGHT3
------------------------------–⎝ ⎠⎛ ⎞ 16µs× AOI_HEIGHT
3------------------------------ 128µs×+ +⎝ ⎠
⎛ ⎞×-------------------------------------------------------------------------------------------------------------------------------------------------------------------=
Frame rate = f(AOI height)
0
2
4
6
8
10
12
14
16
0 200 400 600 800 1000 1200 1400 1600 1800 2000 2200 2400 2600
AOI height / pixel
Fram
e ra
te /
fps
OF-810C Interlaced (Format_7, Mode_0 and Mode_1)
How does bandwidth affect the frame rate?
OSCAR Technical Manual V2.4.0
142
How does bandwidth affect the frame rate?
In some modes the IEEE 1394a bus limits the attainable frame rate. Accord-ing to the 1394a specification on isochronous transfer, the largest data pay-load size of 4096 bytes per 125 µs cycle is possible with bandwidth of 400 Mbit/s. In addition, because of a limitation in an IEEE 1394 module (GP2Lynx), only a maximum number of 4095 packets per frame are allowed.
The following formula establishes the relationship between the required Byte_Per_Packet size and certain variables for the image. It is valid only for Format_7.
If the value for BYTE_PER_PACKET is greater than 4096 (the maximum data payload), the sought-after frame rate cannot be attained.
The attainable frame rate can be calculated using this formula:
(Provision: BYTE_PER_PACKET is divisible by 4):
ByteDepth is based on the following values:
Formula 12: Byte_per_Packet calculation (only Format_7)
Formula 13: Maximum frame rate calculation
Mode bit/pixel byte per pixel
Mono8 8 1
Mono16 16 2
YUV4:2:2 16 2
YUV4:1:1 12 1.5
RGB8 24 3
Table 61: ByteDepth
BYTE_PER_PACKET Framerate AOIWidth× AOIHeight× ByteDepth× 125µs×=
frame rateBYTE_PER_PACKET
AOIWidth AOIHeight× ByteDepth× 125µs×-------------------------------------------------------------------------------------------------------------------≈
How does bandwidth affect the frame rate?
OSCAR Technical Manual V2.4.0
143
Example formula for the Oscar F-810C camera
RGB8, 3272 x 2496 pixel, 2 fps desired
Test images
Loading test images
Formula 14: Example maximum frame rate calculation
FirePackage Fire4Linux
1. Start SmartView.
2. Click the Edit settings button.
3. Click Adv1 tab.
4. In combo box Test images choose Image 1 or another test image.
1. Start cc1394 viewer.
2. In Adjustments menu click on Picture Control.
3. Click Main tab.
4. Activate Test image check box on.
5. In combo box Test images choose Image 1 or another test image.
Table 62: Loading test images in different viewers
BYTE_PER_PACKET 2 3272× 2469× 3× 125µs× 6004 4096>= =
frameratereachable4096
3272 2469× 3× 125µs×------------------------------------------------------------ 1.35=≈⇒
How does bandwidth affect the frame rate?
OSCAR Technical Manual V2.4.0
144
Oscar cameras have two test images.
The second image is in colors:
Figure 62: Test image 1
Figure 63: Test image 2
Configuration of the camera
OSCAR Technical Manual V2.4.0
145
Configuration of the camera
All camera settings are made by writing specific values into the correspond-ing registers.
This applies to:• values for general operating states such as video formats and modes,
exposure times, etc.• extended features of the camera that are turned on and off and con-
trolled via corresponding registers (so-called advanced registers).
Camera_Status_Register
The interoperability of cameras from different manufacturers is ensured by IIDC, formerly DCAM (Digital Camera Specification), published by the IEEE 1394 Trade Association.
IIDC is primarily concerned with setting memory addresses (e.g. CSR: Camera_Status_Register) and their meaning.
In principle all addresses in IEEE 1394 networks are 64 bit long.
The first 10 bit describe the Bus_Id, the next 6 bit the Node_Id.
Of the subsequent 48 bit, the first 16 bit are always FFFFh, leaving the description for the Camera_Status_Register in the last 32 bit.
If a CSR F0F00600h is mentioned below this means in full:
Bus_Id, Node_Id, FFFF F0F00600h
Writing and reading to and from the register can be done with programs such as FireView or by other programs that are developed using an API library (e.g. FirePackage).
Configuration of the camera
OSCAR Technical Manual V2.4.0
146
Every register is 32 bit (big endian) and implemented as follows (MSB = Most Significant Bit; LSB = Least Significant Bit):
ExampleThis requires, for example, that to enable ISO_Enabled mode (see Chapter ISO_Enable / free-run on page 115), (bit 0 in register 614h), the value 80000000 h must be written in the corresponding register.
Far left
Bit
0
Bit
1
Bit
2...
Bit
30
Bit
31
MSB LSB
Table 63: 32-bit register
Configuration of the camera
OSCAR Technical Manual V2.4.0
147
Figure 64: Configuration of the camera
Configuration of the camera
OSCAR Technical Manual V2.4.0
148
Configuration ROM
The information in the configuration ROM is needed to identify the node, its capabilities and which drivers are required.
The base address for the configuration ROM for all registers is FFFF F0000000h.
The configuration ROM is divided into• Bus info block: providing critical information about bus-related capabil-
ities• Root directory: specifying the rest of the content and organization,
such as:– Node unique ID leaf– Unit directory– Unit dependant info
The base address of the camera control register is calculated as follows based on the camera-specific base address:
The entry with key 8D in the root directory (420h in this case) provides the offset for the Node unique ID leaf.
To compute the effective start address of the node unique ID leaf:
Note If you want to use the DirectControl program to read or write to a register, enter the following value in the Address field:
F0F00000h + Offset
Bus info block
Offset 0-7 8-15 16-23 24-31
400h 04 24 45 EE
404h 31 33 39 34 …. ASCII for 1394
408h 20 00 A0 00 …. Bus capabilities
40Ch 00 0A 47 01 …. Node_Vendor_Id, Chip_id_hi
410h 00 00 Serial number …. Chip_id_lo
Root directory
414h 00 04 B7 85 According to IEEE1212, the root directory may have another length. The keys (e.g. 8D) point to the offset factors rather than the offset (e.g.420h) itself.
418h 03 00 0A 47
41Ch 0C 00 83 C0
420h 8D 00 00 02
424h D1 00 00 04
Table 64: Configuration ROM
Configuration of the camera
OSCAR Technical Manual V2.4.0
149
420h + 000002h x 4 = 428h
The entry with key D1 in the root directory (424h in this case) provides the offset for the unit directory as follows:
424h + 000004h x 4 = 434h
The entry with key D4 in the unit directory (440h in this case) provides the offset for unit dependent info:
440h + 000001h * 4 = 444h
To compute the effective start address of the node unique ID leaf
currAddr = node unique ID leaf address
destAddr = address of directory entry
addrOffset = value of directory entry
destAddr = currAddr + (4 x addrOffset)
= 420h + (4 x 000002h)
= 428h
Table 65: Computing effective start address
Offset 0-7 8-15 16-23 24-31
428h 00 02 CA 71
Node unique ID leaf 42Ch 00 0A 47 01
430h 00 00 Serial number
Table 66: Configuration ROM
Offset 0-7 8-15 16-23 24-31
434h 00 03 93 7D
Unit directory 438h 12 00 A0 2D
43Ch 13 00 01 02
440h D4 00 00 01
Table 67: Configuration ROM
Configuration of the camera
OSCAR Technical Manual V2.4.0
150
And finally, the entry with key 40 (448h in this case) provides the offset for the camera control register:
FFFF F0000000h + 3C0000h x 4 = FFFF F0F00000h
The base address of the camera control register is thus:
FFFF F0F00000h
The offset entered in the table always refers to the base address of F0F00000h.
Offset 0-7 8-15 16-23 24-31
444h 00 03 7F 89 ....unit_dep_info_length, CRC
Unit dependent info 448h 40 3C 00 00 ....command_regs_base
44Ch 81 00 00 02 ....vender_name_leaf
450h 82 00 00 06 ....model_name_leaf
Table 68: Configuration ROM
Configuration of the camera
OSCAR Technical Manual V2.4.0
151
Implemented registers (IIDC V1.3)
The following tables show how standard registers from IIDC V1.3 are imple-mented in the camera.• Base address is F0F00000h• Differences and explanations can be found in the Description column.
Camera initialize register
Inquiry register for video format
Offset Name Notes
000h INITIALIZE Assert MSB = 1 for Init.
Table 69: Camera initialize register
Offset Name Field Bit Description
100h V_FORMAT_INQ Format_0 [0] Up to VGA (non compressed)
Format_1 [1] SVGA to XGA
Format_2 [2] SXGA to UXGA
Format_3 [3..5] Reserved
Format_6 [6] Still Image Format
Format_7 [7] Partial Image Format
--- [8..31] Reserved
Table 70: Format inquiry register
Configuration of the camera
OSCAR Technical Manual V2.4.0
152
Inquiry register for video mode
Offset Name Field Bit Description Color mode
180h V_MODE_INQ
(Format_0)
Mode_0 [0] 160 x 120 YUV 4:4:4
Mode_1 [1] 320 x 240 YUV 4:2:2
Mode_2 [2] 640 x 480 YUV 4:1:1
Mode_3 [3] 640 x 480 YUV 4:2:2
Mode_4 [4] 640 x 480 RGB
Mode_5 [5] 640 x 480 MONO8
Mode_6 [6] 640 x 480 MONO16
Mode_X [7] Reserved
--- [8..31] Reserved (zero)
184h V_MODE_INQ
(Format_1)
Mode_0 [0] 800 x 600 YUV 4:2:2
Mode_1 [1] 800 x 600 RGB
Mode_2 [2] 800 x 600 MONO8
Mode_3 [3] 1024 x 768 YUV 4:2:2
Mode_4 [4] 1024 x 768 RGB
Mode_5 [5] 1024 x 768 MONO8
Mode_6 [6] 800 x 600 MONO16
Mode_7 [7] 1024 x 768 MONO16
--- [8..31] Reserved (zero)
188h V_MODE_INQ
(Format_2)
Mode_0 [0] 1280 x 960 YUV 4:2:2
Mode_1 [1] 1280 x 960 RGB
Mode_2 [2] 1280 x 960 MONO8
Mode_3 [3] 1600 x 1200 YUV 4:2:2
Mode_4 [4] 1600 x 1200 RGB
Mode_5 [5] 1600 x 1200 MONO8
Mode_6 [6] 1280 x 960 MONO16
Mode_7 [7] 1600 x 1200 MONO16
--- [8..31] Reserved (zero)
18Ch
…
197h
Reserved for other V_MODE_INQ_x for Format_x. Always 0
198h V_MODE_INQ_6 (Format_6) Always 0
Table 71: Video mode inquiry register
Configuration of the camera
OSCAR Technical Manual V2.4.0
153
Inquiry register for video frame rate and base address
19Ch V_MODE_INQ
(Format_7)
Mode_0 [0] Format_7 Mode_0
Mode_1 [1] Format_7 Mode_1
Mode_2 [2] Format_7 Mode_2
Mode_3 [3] Format_7 Mode_3
Mode_4 [4] Format_7 Mode_4
Mode_5 [5] Format_7 Mode_5
Mode_6 [6] Format_7 Mode_6
Mode_7 [7] Format_7 Mode_7
--- [8..31] Reserved (zero)
Offset Name Field Bit Description
200h V_RATE_INQ
(Format_0, Mode_0)
FrameRate_0 [0] Reserved
FrameRate_1 [1] Reserved
FrameRate_2 [2] 7.5 fps
FrameRate_3 [3] 15 fps
FrameRate_4 [4] 30 fps
FrameRate_5 [5] 60 fps
FrameRate_6 [6] 120 fps (IIDC V1.31)
FrameRate_7 [7] 240 fps (IIDC V1.31)
--- [8..31] Reserved (zero)
204h V_RATE_INQ
(Format_0, Mode_1)
FrameRate_0 [0] 1.875 fps
FrameRate_1 [1] 3.75 fps
FrameRate_2 [2] 7.5 fps
FrameRate_3 [3] 15 fps
FrameRate_4 [4] 30 fps
FrameRate_5 [5] 60 fps
FrameRate_6 [6] 120 fps (IIDC V1.31)
FrameRate_7 [7] 240 fps (IIDC V1.31)
--- [8..31] Reserved (zero)
Table 72: Frame rate inquiry register
Offset Name Field Bit Description Color mode
Table 71: Video mode inquiry register
Configuration of the camera
OSCAR Technical Manual V2.4.0
154
208h V_RATE_INQ
(Format_0, Mode_2)
FrameRate_0 [0] 1.875 fps
FrameRate_1 [1] 3.75 fps
FrameRate_2 [2] 7.5 fps
FrameRate_3 [3] 15 fps
FrameRate_4 [4] 30 fps
FrameRate_5 [5] 60 fps
FrameRate_6 [6] 120 fps (IIDC V1.31)
FrameRate_7 [7] 240 fps (IIDC V1.31)
--- [8..31] Reserved (zero)
20Ch V_RATE_INQ
(Format_0, Mode_3)
FrameRate_0 [0] 1.875 fps
FrameRate_1 [1] 3.75 fps
FrameRate_2 [2] 7.5 fps
FrameRate_3 [3] 15 fps
FrameRate_4 [4] 30 fps
FrameRate_5 [5] 60 fps
FrameRate_6 [6] 120 fps (IIDC V1.31)
FrameRate_7 [7] 240 fps (IIDC V1.31)
--- [8..31] Reserved (zero)
210h V_RATE_INQ
(Format_0, Mode_4)
FrameRate_0 [0] 1.875 fps
FrameRate_1 [1] 3.75 fps
FrameRate_2 [2] 7.5 fps
FrameRate_3 [3] 15 fps
FrameRate_4 [4] 30 fps
FrameRate_5 [5] 60 fps
FrameRate_6 [6] 120 fps (IIDC V1.31)
FrameRate_7 [7] 240 fps (IIDC V1.31)
--- [8..31] Reserved (zero)
Offset Name Field Bit Description
Table 72: Frame rate inquiry register
Configuration of the camera
OSCAR Technical Manual V2.4.0
155
214h V_RATE_INQ
(Format_0, Mode_5)
FrameRate_0 [0] 1.875 fps
FrameRate_1 [1] 3.75 fps
FrameRate_2 [2] 7.5 fps
FrameRate_3 [3] 15 fps
FrameRate_4 [4] 30 fps
FrameRate_5 [5] 60 fps
FrameRate_6 [6] 120 fps (IIDC V1.31)
FrameRate_7 [7] 240 fps (IIDC V1.31)
--- [8..31] Reserved (zero)
218h V_RATE_INQ
(Format_0, Mode_6)
FrameRate_0 [0] 1.875 fps
FrameRate_1 [1] 3.75 fps
FrameRate_2 [2] 7.5 fps
FrameRate_3 [3] 15 fps
FrameRate_4 [4] 30 fps
FrameRate_5 [5] 60 fps
FrameRate_6 [6] 120 fps (IIDC V1.31)
FrameRate_7 [7] 240 fps (IIDC V1.31)
--- [8..31] Reserved (zero)
21Ch
…
21Fh
Reserved V_RATE_INQ_0_x (for other Mode_x of Format_0)
Always 0
220h V_RATE_INQ
(Format_1, Mode_0)
FrameRate_0 [0] Reserved
FrameRate_1 [1] 3.75 fps
FrameRate_2 [2] 7.5 fps
FrameRate_3 [3] 15 fps
FrameRate_4 [4] 30 fps
FrameRate_5 [5] 60 fps
FrameRate_6 [6] 120 fps (IIDC V1.31)
FrameRate_7 [7] 240 fps (IIDC V1.31)
--- [8..31] Reserved (zero)
Offset Name Field Bit Description
Table 72: Frame rate inquiry register
Configuration of the camera
OSCAR Technical Manual V2.4.0
156
224h V_RATE_INQ
(Format_1, Mode_1)
FrameRate_0 [0] Reserved
FrameRate_1 [1] Reserved
FrameRate_2 [2] 7.5 fps
FrameRate_3 [3] 15 fps
FrameRate_4 [4] 30 fps
FrameRate_5 [5] 60 fps
FrameRate_6 [6] 120 fps (IIDC V1.31)
FrameRate_7 [7] 240 fps (IIDC V1.31)
--- [8..31] Reserved (zero)
228h V_RATE_INQ
(Format_1, Mode_2)
FrameRate_0 [0] Reserved
FrameRate_1 [1] Reserved
FrameRate_2 [2] 7.5 fps
FrameRate_3 [3] 15 fps
FrameRate_4 [4] 30 fps
FrameRate_5 [5] 60 fps
FrameRate_6 [6] 120 fps (IIDC V1.31)
FrameRate_7 [7] 240 fps (IIDC V1.31)
--- [8..31] Reserved (zero)
22Ch V_RATE_INQ
(Format_1, Mode_3)
FrameRate_0 [0] 1.875 fps
FrameRate_1 [1] 3.75 fps
FrameRate_2 [2] 7.5 fps
FrameRate_3 [3] 15 fps
FrameRate_4 [4] 30 fps
FrameRate_5 [5] 60 fps
FrameRate_6 [6] 120 fps (IIDC V1.31)
FrameRate_7 [7] 240 fps (IIDC V1.31)
--- [8..31] Reserved (zero)
Offset Name Field Bit Description
Table 72: Frame rate inquiry register
Configuration of the camera
OSCAR Technical Manual V2.4.0
157
230h V_RATE_INQ
(Format_1, Mode_4)
FrameRate_0 [0] 1.875 fps
FrameRate_1 [1] 3.75 fps
FrameRate_2 [2] 7.5 fps
FrameRate_3 [3] 15 fps
FrameRate_4 [4] 30 fps
FrameRate_5 [5] 60 fps
FrameRate_6 [6] 120 fps (IIDC V1.31)
FrameRate_7 [7] 240 fps (IIDC V1.31)
--- [8..31] Reserved (zero)
234h V_RATE_INQ
(Format_1, Mode_5)
FrameRate_0 [0] 1.875 fps
FrameRate_1 [1] 3.75 fps
FrameRate_2 [2] 7.5 fps
FrameRate_3 [3] 15 fps
FrameRate_4 [4] 30 fps
FrameRate_5 [5] 60 fps
FrameRate_6 [6] 120 fps (IIDC V1.31)
FrameRate_7 [7] 240 fps (IIDC V1.31)
--- [8..31] Reserved (zero)
238h V_RATE_INQ
(Format_1, Mode_6)
FrameRate_0 [0] 1.875 fps
FrameRate_1 [1] 3.75 fps
FrameRate_2 [2] 7.5 fps
FrameRate_3 [3] 15 fps
FrameRate_4 [4] 30 fps
FrameRate_5 [5] 60 fps
FrameRate_6 [6] 120 fps (IIDC V1.31)
FrameRate_7 [7] 240 fps (IIDC V1.31)
--- [8..31] Reserved (zero)
Offset Name Field Bit Description
Table 72: Frame rate inquiry register
Configuration of the camera
OSCAR Technical Manual V2.4.0
158
23Ch V_RATE_INQ
(Format_1, Mode_7)
FrameRate_0 [0] 1.875 fps
FrameRate_1 [1] 3.75 fps
FrameRate_2 [2] 7.5 fps
FrameRate_3 [3] 15 fps
FrameRate_4 [4] 30 fps
FrameRate_5 [5] 60 fps
FrameRate_6 [6] 120 fps (IIDC V1.31)
FrameRate_7 [7] Reserved
--- [8..31] Reserved (zero)
240h V_RATE_INQ
(Format_2, Mode_0)
FrameRate_0 [0] 1.875 fps
FrameRate_1 [1] 3.75 fps
FrameRate_2 [2] 7.5 fps
FrameRate_3 [3] 15 fps
FrameRate_4 [4] 30 fps
FrameRate_5 [5] 60 fps
FrameRate_6 [6] Reserved
FrameRate_7 [7] Reserved
--- [8..31] Reserved (zero)
244h V_RATE_INQ
(Format_2, Mode_1)
FrameRate_0 [0] 1.875 fps
FrameRate_1 [1] 3.75 fps
FrameRate_2 [2] 7.5 fps
FrameRate_3 [3] 15 fps
FrameRate_4 [4] 30 fps
FrameRate_5 [5] 60 fps
FrameRate_6 [6] Reserved
FrameRate_7 [7] Reserved
--- [8..31] Reserved (zero)
Offset Name Field Bit Description
Table 72: Frame rate inquiry register
Configuration of the camera
OSCAR Technical Manual V2.4.0
159
248h V_RATE_INQ
(Format_2, Mode_2)
FrameRate_0 [0] 1.875 fps
FrameRate_1 [1] 3.75 fps
FrameRate_2 [2] 7.5 fps
FrameRate_3 [3] 15 fps
FrameRate_4 [4] 30 fps
FrameRate_5 [5] 60 fps
FrameRate_6 [6] 120 fps (IIDC V1.31)
FrameRate_7 [7] Reserved
--- [8..31] Reserved (zero)
24Ch V_RATE_INQ
(Format_2, Mode_3)
FrameRate_0 [0] 1.875 fps
FrameRate_1 [1] 3.75 fps
FrameRate_2 [2] 7.5 fps
FrameRate_3 [3] 15 fps
FrameRate_4 [4] 30 fps
FrameRate_5 [5] 60 fps
FrameRate_6 [6] Reserved
FrameRate_7 [7] Reserved
--- [8..31] Reserved (zero)
250h V_RATE_INQ
(Format_2, Mode_4)
FrameRate_0 [0] 1.875 fps
FrameRate_1 [1] 3.75 fps
FrameRate_2 [2] 7.5 fps
FrameRate_3 [3] 15 fps
FrameRate_4 [4] 30 fps
FrameRate_5 [5] Reserved
FrameRate_6 [6] Reserved
FrameRate_7 [7] Reserved
--- [8..31] Reserved (zero)
Offset Name Field Bit Description
Table 72: Frame rate inquiry register
Configuration of the camera
OSCAR Technical Manual V2.4.0
160
254h V_RATE_INQ
(Format_2, Mode_5)
FrameRate_0 [0] 1.875 fps
FrameRate_1 [1] 3.75 fps
FrameRate_2 [2] 7.5 fps
FrameRate_3 [3] 15 fps
FrameRate_4 [4] 30 fps
FrameRate_5 [5] 60 fps
FrameRate_6 [6] Reserved
FrameRate_7 [7] Reserved
--- [8..31] Reserved (zero)
258h V_RATE_INQ
(Format_2, Mode_6)
FrameRate_0 [0] 1.875 fps
FrameRate_1 [1] 3.75 fps
FrameRate_2 [2] 7.5 fps
FrameRate_3 [3] 15 fps
FrameRate_4 [4] 30 fps
FrameRate_5 [5] 60 fps
FrameRate_6 [6] Reserved
FrameRate_7 [7] Reserved
--- [8..31] Reserved (zero)
25Ch V_RATE_INQ
(Format_2, Mode_7)
FrameRate_0 [0] 1.875 fps
FrameRate_1 [1] 3.75 fps
FrameRate_2 [2] 7.5 fps
FrameRate_3 [3] 15 fps
FrameRate_4 [4] 30 fps
FrameRate_5 [5] 60 fps
FrameRate_6 [6] Reserved
FrameRate_7 [7] Reserved
--- [8..31] Reserved
260h
…
2BFh
Reserved V_RATE_INQ_y_x (for other Format_y, Mode_x)
2C0h V_REV_INQ_6_0 (Format_6, Mode_0) Always 0
2C4h
..
2DFh
Reserved V_REV_INQ_6_x (for other Mode_x of Format_6) Always 0
Offset Name Field Bit Description
Table 72: Frame rate inquiry register
Configuration of the camera
OSCAR Technical Manual V2.4.0
161
2E0hV-CSR_INQ_7_0
[0..31] CSR_quadlet offset for Format_7 Mode_0
2E4hV-CSR_INQ_7_1
[0..31] CSR_quadlet offset for Format_7 Mode_1
2E8hV-CSR_INQ_7_2
[0..31] CSR_quadlet offset for Format_7 Mode_2
2EChV-CSR_INQ_7_3
[0..31] CSR_quadlet offset for Format_7 Mode_3
2F0hV-CSR_INQ_7_4
[0..31] CSR_quadlet offset for Format_7 Mode_4
2F4hV-CSR_INQ_7_5
[0..31] CSR_quadlet offset for Format_7 Mode_5
2F8hV-CSR_INQ_7_6
[0..31] CSR_quadlet offset for Format_7 Mode_6
2FChV-CSR_INQ_7_7
[0..31] CSR_quadlet offset for Format_7 Mode_7
Offset Name Field Bit Description
Table 72: Frame rate inquiry register
Configuration of the camera
OSCAR Technical Manual V2.4.0
162
Inquiry register for basic function
Offset Name Field Bit Description
400h BASIC_FUNC_INQ Advanced_Feature_Inq [0] Inquiry for advanced features (vendor unique features)
Vmode_Error_Status_Inq [1] Inquiry for existence of Vmode_Error_Status register
Feature_Control_Error_Status_Inq [2] Inquiry for existence of Feature_Control_Error_Status
Opt_Func_CSR_Inq [3] Inquiry for Opt_Func_CSR
--- [4..7] Reserved
1394b_mode_Capability [8] Inquiry for 1394b_mode_Capability
--- [9..15] Reserved
Cam_Power_Cntl [16] Camera process power ON/OFF capability
--- [17..18] Reserved
One_Shot_Inq [19] One-shot transmission capa-bility
Multi_Shot_Inq [20] Multi-shot transmission capability
--- [21..27] Reserved
Memory_Channel [28..31] Maximum memory channel number (N)If 0000, no user memory available
Table 73: Basic function inquiry register
Configuration of the camera
OSCAR Technical Manual V2.4.0
163
Inquiry register for feature presence
Offset Name Field Bit Description
404h FEATURE_HI_INQ Brightness [0] Brightness control
Auto_Exposure [1] Auto exposure control
Sharpness [2] Sharpness control
White_Balance [3] White balance control
Hue [4] Hue control
Saturation [5] Saturation control
Gamma [6] Gamma control
Shutter [7] Shutter control
Gain [8] Gain control
Iris [9] Iris control
Focus [10] Focus control
Temperature [11] Temperature control
Trigger [12] Trigger control
Trigger_Delay [13] Trigger delay control
White_Shading [14] White shading control
Frame_Rate [15] Frame rate control
--- [16..31] Reserved
408h FEATURE_LO_INQ Zoom [0] Zoom control
Pan [1] Pan control
Tilt [2] Tilt control
Optical_Filter [3] Optical filter control
--- [4..15] Reserved
Capture_Size [16] Capture size for Format_6
Capture_Quality [17] Capture quality for Format_6
--- [16..31] Reserved
40Ch OPT_FUNCTION_INQ --- [0] Reserved
PIO [1] Parallel input/output control
SIO [2] Serial input/output control
Strobe_out [4..31] Strobe signal output
Table 74: Feature presence inquiry register
Configuration of the camera
OSCAR Technical Manual V2.4.0
164
410h
..
47Fh
Reserved Address error on access
480h Advanced_Feature_Inq Advanced_Feature_Quadlet_Offset [0..31] Quadlet offset of the advanced feature CSRs from the base address of initial register space (vendor unique)
This register is the offset for the Access_Control_Register and thus the base address for advanced Features.
Access_Control_Register does not prevent access to advanced features. In some programs it should still always be activated first. Advanced Feature Set Unique Value is 7ACh and CompanyID is A47h.
484h PIO_Control_CSR_Inq PIO_Control_Quadlet_Offset [0..31] Quadlet offset of the PIO_Control CSRs from the base address of initial regis-ter space (vendor unique)
488h SIO_Control_CSR_Inq SIO_Control_Quadlet_Offset [0..31] Quadlet offset of the SIO_Control CSR's from the base address of initial regis-ter space (vendor unique)
48Ch Strobe_Output_CSR_Inq Strobe_Output_Quadlet_Offset [0..31] Quadlet offset of the Strobe_Output signal CSRs from the base address of ini-tial register space (vendor unique)
Offset Name Field Bit Description
Table 74: Feature presence inquiry register
Configuration of the camera
OSCAR Technical Manual V2.4.0
165
Inquiry register for feature elements
Register Name Field Bit Description
0xF0F00500 BRIGHTNESS_INQUIRY Presence_Inq [0] Indicates presence of this feature (read only)
Abs_Control_Inq [1] Capability of control with absolute value
--- [2] Reserved
One_Push_Inq [3] One-push auto mode (con-trolled automatically by the camera once)
Readout_Inq [4] Capability of reading out the value of this feature
ON_OFF [5] Capability of switching this feature ON and OFF
Auto_Inq [6] Auto mode (controlled auto-matically by the camera)
Manual_Inq [7] Manual mode (controlled by user)
Min_Value [8..19] Minimum value for this fea-ture
Max_Value [20..31] Maximum value for this fea-ture
504h AUTO_EXPOSURE_INQ Same definition as Brightness_inq.
508h SHARPNESS_INQ Same definition as Brightness_inq.
50Ch WHITE_BAL_INQ Same definition as Brightness_inq.
510h HUE_INQ Same definition as Brightness_inq.
514h SATURATION_INQ Same definition as Brightness_inq.
518h GAMMA_INQ Same definition as Brightness_inq.
51Ch SHUTTER_INQ Same definition as Brightness_inq.
520h GAIN_INQ Same definition as Brightness_inq.
524h IRIS_INQ Always 0
528h FOCUS_INQ Always 0
52Ch TEMPERATURE_INQ Same definition as Brightness_inq.
Table 75: Feature elements inquiry register
Configuration of the camera
OSCAR Technical Manual V2.4.0
166
530h TRIGGER_INQ Presence_Inq [0] Indicates presence of this feature (read only)
Abs_Control_Inq [1] Capability of control with absolute value
--- [2..3 Reserved
Readout_Inq [4] Capability of reading out the value of this feature
ON_OFF [5] Capability of switching this feature ON and OFF
Polarity_Inq [6] Capability of changing the polarity of the trigger input
--- [7..15] Reserved
Trigger_Mode0_Inq [16] Presence of Trigger_Mode_0
Trigger_Mode1_Inq [17] Presence of Trigger_Mode_1
Trigger_Mode2_Inq [18] Presence of Trigger_Mode_2
Trigger_Mode3_Inq [19] Presence of Trigger_Mode_3
--- [20..31 Reserved
534h TRIGGER_DELAY_INQUIRY Presence_Inq [0] Indicates presence of this feature (read only)
Abs_Control_Inq [1] Capability of control with absolute value
--- [2] Reserved
One_Push_Inq [3] One-push auto mode con-trolled automatically by the camera once)
Readout_Inq [4] Capability of reading out the value of this feature
ON_OFF [5] Capability of switching this feature ON and OFF
Auto_Inq [6] Auto mode (controlled auto-matically by the camera)
Manual_Inq [7] Manual mode (controlled by user)
Min_Value [8..19] Minimum value for this fea-ture
Max_Value [20..31] Maximum value for this fea-ture
538 .. 57Ch Reserved for other FEATURE_HI_INQ
Register Name Field Bit Description
Table 75: Feature elements inquiry register
Configuration of the camera
OSCAR Technical Manual V2.4.0
167
580h ZOOM_INQ Always 0
584h PAN_INQ Always 0
588h TILT_INQ Always 0
58Ch OPTICAL_FILTER_INQ Always 0
590
..
5BCh
Reserved for other FEATURE_LO_INQ
Always 0
5C0h CAPTURE_SIZE_INQ Always 0
5C4h CAPTURE_QUALITY_INQ Always 0
5C8h
..
5FCh
Reserved for other FEATURE_LO_INQ
Always 0
600h CUR-V-Frm_RATE/Revision Bit [0..2] for the frame rate
604h CUR-V-MODE Bit [0..2] for the current video mode
608h CUR-V-FORMAT Bit [0..2] for the current video format
60Ch ISO-Channel Bit [0..3] for channel, [6..7] for ISO speed
610h Camera_Power Always 0
614h ISO_EN/Continuous_Shot Bit 0: 1 for continuous shot; 0 for stop
618h Memory_Save Always 0
61Ch One_Shot, Multi_Shot, Count Number
See Chapter One-shot on page 113
See Chapter Multi-shot on page 115
620h Mem_Save_Ch Always 0
624 Cur_Mem_Ch Always 0
628h Vmode_Error_Status Error in combination of format/mode/ISO speed:
Bit(0): No error; Bit(0)=1: error
Register Name Field Bit Description
Table 75: Feature elements inquiry register
Configuration of the camera
OSCAR Technical Manual V2.4.0
168
Inquiry register for absolute value CSR offset address
Offset Name Notes
700h ABS_CSR_HI_INQ_0 Always 0
704h ABS_CSR_HI_INQ_1 Always 0
708h ABS_CSR_HI_INQ_2 Always 0
70Ch ABS_CSR_HI_INQ_3 Always 0
710h ABS_CSR_HI_INQ_4 Always 0
714h ABS_CSR_HI_INQ_5 Always 0
718h ABS_CSR_HI_INQ_6 Always 0
71Ch ABS_CSR_HI_INQ_7 Always 0
720h ABS_CSR_HI_INQ_8 Always 0
724h ABS_CSR_HI_INQ_9 Always 0
728h ABS_CSR_HI_INQ_10 Always 0
72Ch ABS_CSR_HI_INQ_11 Always 0
730h ABS_CSR_HI_INQ_12 Always 0
734
..
77Fh
Reserved Always 0
780h ABS_CSR_LO_INQ_0 Always 0
784h ABS_CSR_LO_INQ_1 Always 0
788h ABS_CSR_LO_INQ_2 Always 0
78Ch ABS_CSR_LO_INQ_3 Always 0
790h
..
7BFh
Reserved Always 0
7C0h ABS_CSR_LO_INQ_16 Always 0
7C4h ABS_CSR_LO_INQ_17 Always 0
7C8h
..
7FFh
Reserved Always 0
Table 76: Absolute value inquiry register
Configuration of the camera
OSCAR Technical Manual V2.4.0
169
Status and control register for one-pushThe one-push feature WHITE_BALANCE, is currently implemented. If this flag is set, the feature becomes immediately active, even if no images are being input (see Chapter One-push automatic white balance on page 61).
Offset Name Field Bit Description
800h BRIGHTNESS Presence_Inq [0] Presence of this feature
0: N/A
1: Available
Abs_Control [1] Absolute value control
0: Control with value in the Value field
1: Control with value in the Absolute value CSR
If this bit = 1, value in the Value field is ignored.
--- [2-4] Reserved
One_Push [5] Write 1: begin to work (Self cleared after operation)
Read: Value=1 in operation
Value=0 not in operation
If A_M_Mode =1, this bit is ignored.
ON_OFF [6] Write: ON or OFF this feature
Read: read a status
0: OFF, 1: ON
If this bit =0, other fields will be read only.
A_M_Mode [7] Write: set the mode
Read: read a current mode
0: Manual
1: Auto
--- [8-19] Reserved
Value [20-31] Value.
Write the value in Auto mode, this field is ignored.
If ReadOut capability is not available, read value has no meaning.
Table 77: Feature control register
Configuration of the camera
OSCAR Technical Manual V2.4.0
170
804h AUTO-EXPOSURE See above
Note: Target grey level parameter in SmartView corresponds to Auto_exposure register 0xF0F00804 (IIDC).
808h SHARPNESS See above
Offset Name Field Bit Description
Table 77: Feature control register
Configuration of the camera
OSCAR Technical Manual V2.4.0
171
80Ch WHITE-BALANCE Presence_Inq [0] Presence of this feature
0: N/A1: Available
Always 0 for Mono
Abs_Control [1] Absolute value control
0: Control with value in the Value field1: Control with value in the Absolute value CSR
If this bit = 1, value in the Value field is ignored.
--- [2-4] Reserved
One_Push [5] Write '1': begin to work (Self cleared after operation)
Read: Value='1' in operation
Value='0' not in operation
If A_M_Mode =1, this bit is ignored.
ON_OFF [6] Write: ON or OFF this feature,
Read: read a status
0: OFF1: ON
If this bit =0, other fields will be read only.
A_M_Mode [7] Write: set the mode
Read: read a current mode
0: Manual1: Auto
U_Value /
B_Value
[8-19] U value / B value
Write the value in AUTO mode, this field is ignored.
If ReadOut capability is not available, read value has no meaning.
V_Value /
R_Value
[20-31] V value / R value
Write the value in AUTO mode, this field is ignored.
If ReadOut capability is not available, read value has no meaning.
Offset Name Field Bit Description
Table 77: Feature control register
Configuration of the camera
OSCAR Technical Manual V2.4.0
172
810h HUE See above
Always 0 for Mono
814h SATURATION See above
Always 0 for Mono
818h GAMMA See above
81Ch SHUTTER see Advanced Feature time base
See Table 26: CSR: Shutter on page 70
820h GAIN See above
824h IRIS Always 0
828h FOCUS Always 0
82Ch TEMPERATURE Always 0
830h TRIGGER-MODE Can be effected via advanced feature IO_INP_CTRLx.
834h
..
87C
Reserved for other FEATURE_HI
Always 0
880h Zoom Always 0
884h PAN Always 0
888h TILT Always 0
88Ch OPTICAL_FILTER Always 0
890
..
8BCh
Reserved for other FEATURE_LO
Always 0
8C0h CAPTURE-SIZE Always 0
8C4h CAPTURE-QUALITY Always 0
8C8h .. 8FCh
Reserved for other FEATURE_LO
Always 0
Offset Name Field Bit Description
Table 77: Feature control register
Configuration of the camera
OSCAR Technical Manual V2.4.0
173
Feature control error status register
Video mode control and status registers for Format_7
Quadlet offset Format_7 Mode_0
The quadlet offset to the base address for Format_7 Mode_0, which can be read out at F0F002E0h (according to Table 72: Frame rate inquiry register on page 153) gives 003C2000h.
4 x 3C2000h = F08000h so that the base address for the latter (Table 79: Format_7 control and status register on page 173) equals toF0000000h + F08000h = F0F08000h.
Quadlet offset Format_7 Mode_1
The quadlet offset to the base address for Format_7 Mode_1, which can be read out at F0F002E4h (according to Table 72: Frame rate inquiry register on page 153) gives 003C2400h.
4 x 003C2400h = F09000h so that the base address for the latter (Table 79: Format_7 control and status register on page 173) equals toF0000000h + F09000h = F0F09000h.
Format_7 control and status register (CSR)
Offset Name Notes
640h Feature_Control_Error_Status_HI Always 0
644h Feature_Control_Error_Status_LO Always 0
Table 78: Feature control error register
Note Color_Coding_ID and Inq is important for the various (above standard) color modes of the OSCAR cameras and is explained in Chapter Video formats, modes and bandwidth on page 120.
Offset Name Notes
000h MAX_IMAGE_SIZE_INQ According to IIDC V1.3
004h UNIT_SIZE_INQ According to IIDC V1.3
008h IMAGE_POSITION According to IIDC V1.3
Table 79: Format_7 control and status register
Configuration of the camera
OSCAR Technical Manual V2.4.0
174
00Ch IMAGE_SIZE According to IIDC V1.3
010h COLOR_CODING_ID See note
014h COLOR_CODING_INQ According to IIDC V1.3
034h PIXEL_NUMER_INQ According to IIDC V1.3
038h TOTAL_BYTES_HI_INQ According to IIDC V1.3
03Ch TOTAL_BYTES_LO_INQ According to IIDC V1.3
040h PACKET_PARA_INQ See note
044h BYTE_PER_PACKET According to IIDC V1.3
Note • For all modes in Format_7, ErrorFlag_1 and ErrorFlag_2 are refreshed on each access to the Format_7 register.
• Contrary to IIDC V1.3, registers relevant to Format_7 are refreshed on each access. The Setting_1 bit is automatically cleared after each access.
• When ErrorFlag_1 or ErrorFlag_2 are set and Format_7 is configured, no image capture is started.
• Contrary to IIDC v.1.3, COLOR_CODING_ID is set to a default value after an INITIALIZE or reset.
• Contrary to IIDC V1.3, the UnitBytePerPacket field is already filled in with a fixed value in the PACKET_PARA_INQ register.
Offset Name Notes
Table 79: Format_7 control and status register
Configuration of the camera
OSCAR Technical Manual V2.4.0
175
Advanced features (AVT-specific)
The camera has a variety of extended features going beyond the possibilities described in IIDC V1.3. The following chapter summarizes all available advanced features in ascending register order.
Advanced registers summaryThe following table gives an overview of all available advanced registers:
Note This chapter is a reference guide for advanced registers and does not explain the advanced features itself. For detailed description of the theoretical background see
• Chapter Description of the data path on page 52• Links given in the table below
Register Register name Description
0XF1000010 VERSION_INFO See Table 81: Advanced register: Version informa-tion on page 177
0XF1000040 ADV_INQ_1 See Table 83: Advanced register: Advanced feature inquiry on page 1820XF1000044 ADV_INQ_2
0XF1000200 MAX_RESOLUTION See Table 84: Advanced register: Maximum resolu-tion inquiry on page 183
0XF1000208 TIMEBASE See Table 85: Advanced register: Time base on page 184
0XF100020C EXTD_SHUTTER See Table 87: Advanced register: Extended shutter on page 185
0XF1000210 TEST_IMAGE
0XF1000220 SEQUENCE_CTRL except MF131x and OSCAR
0XF1000224 SEQUENCE_PARAM except MF131x and OSCAR
0XF1000240 LUT_CTRL
0XF1000244 LUT_MEM_CTRL
0XF1000248 LUT_INFO
0XF1000250 SHDG_CTRL
0XF1000254 SHDG_MEM_CTRL
0XF1000258 SHDG_INFO
0XF1000260 DEFERRED_TRANS
0XF1000270 FRAMEINFO
0XF1000274 FRAMECOUNTER see FRMCNT_STAMP
Table 80: Advanced registers summary
Configuration of the camera
OSCAR Technical Manual V2.4.0
176
0XF1000280 HDR_CONTROL MF131x only
0XF1000284 KNEEPOINT_1 MF131x only
0XF1000288 KNEEPOINT_2 MF131x only
0XF100028C KNEEPOINT_3 MF131x only
0XF1000290 DSNU_CONTROL MF131B only; Firmware 2.02
0XF1000294 BLEMISH_CONTROL MF131x only; Firmware 2.02
0XF1000300 IO_INP_CTRL1
0XF1000304 IO_INP_CTRL2
0XF1000308 IO_INP_CTRL3 Dolphin series only
0XF1000320 IO_OUTP_CTRL1
0XF1000324 IO_OUTP_CTRL2
0XF1000328 IO_OUTP_CTRL3 Dolphin series only
0XF1000340 IO_INTENA_DELAY
0XF1000360 AUTOSHUTTER_CTRL Marlin/Oscar series only
0XF1000364 AUTOSHUTTER_LO Marlin/Oscar series only
0XF1000368 AUTOSHUTTER_HI Marlin/Oscar series only
0XF1000370 AUTOGAIN_CTRL Marlin/Oscar series only
0XF1000390 AUTOFNC_AOI Marlin/Oscar series only
0XF10003A0 COLOR_CORR Marlin/Oscar CCD type color cameras only
0XF1000400 TRIGGER_DELAY
0XF1000410 MIRROR_IMAGE Marlin/Oscar series only
0XF1000414 MNR
0XF1000510 SOFT_RESET
0XF1000520 HIGH_SNR OSCAR only
0XF1000550 USER_PROFILE
0XF1000600 TIMESTAMP aka secure image signature (SIS)
Marlin series only
0XF1000610 FRMCNT_STAMP Marlin series only
0XF1000620 TRGCNT_STAMP Marlin series only
0XF1000FFC GPDATA_INFO
0XF1001000 GPDATA_BUFFER
Register Register name Description
Table 80: Advanced registers summary
Configuration of the camera
OSCAR Technical Manual V2.4.0
177
Version information registerThe presence of each of the following features can be queried by the 0 bit of the corresponding register.
This register holds information about the node_hw_version, the node_sw_version and the node_spec_ID (camera type). µC version and FPGA version are bcd-coded, which means that e.g. firmware version 0.85 is read as 0x0085.
The FPGA type ID (= camera type ID) identifies the camera type with the help of the following list:
Note Always activate advanced features before accessing them.
Note • Currently all registers can be written without being activated. This makes it easier to operate the camera using Directcontrol.
• AVT reserves the right to require activation in future versions of the software.
Register Name Field Bit Description
0xF1000010 VERSION_INFO1 µC type ID [0..15] Reserved
µC version [16..31] Bcd-coded version number
0xF1000014 [0..31] Reserved
0xF1000018 VERSION_INFO3 Camera type ID [0..15] See below
FPGA version [16..31] Bcd-coded version number
0xF100001C [0..31] Reserved
Table 81: Advanced register: Version information
ID (decimal) Camera type
1 F145b
2 F145c
3 F201b
4 F201c
5 F145b-1
Table 82: Camera type ID list
Configuration of the camera
OSCAR Technical Manual V2.4.0
178
6 F145c-1
7 F201b-1
8 F201c-1
9 MF033B
10 MF033C
11 MF046B
12 MF046C
13 MF080B
14 MF080C
15 MF145B2
16 MF145C2
17 MF131B
18 MF131C
19 MF145B2-15fps
20 MF145C2-15fps
21 M2F033B
22 M2F033C
23 M2F046B
24 M2F046C
25 M2F080B
26 M2F080C
27 M2F145B2
28 M2F145C2
31 M2F145B2-15fps
32 M2F145C2-15fps
38 OF320C
40 OF510C
42 OF810C
43 M2F080B-30fps
44 M2F080C-30fps
45 M2F145B2-ASM
46 MM2F145C2-ASM
ID (decimal) Camera type
Table 82: Camera type ID list
Configuration of the camera
OSCAR Technical Manual V2.4.0
179
47 M2F201B
48 M2F201C
49 M2F146B
50 M2F146C
101 PIKE F-032B
102 PIKE F-032C
103 PIKE F-100B
104 PIKE F-100C
105 PIKE F-145B
106 PIKE F-145C
107 PIKE F-210B
108 PIKE F-210C
109 -
110 -
111 PIKE F-421B
112 PIKE F-421C
201 GUPPY F-033B
202 GUPPY F-033C
203 GUPPY F-036B
204 GUPPY F-036C
205 GUPPY F-046B
206 GUPPY F-046C
207 GUPPY F-080B
208 GUPPY F-080C
209 -
210 -
211 -
212 -
213 GUPPY F-033B BL (board level)
214 GUPPY F-033C BL (board level)
215 GUPPY F-025B
216 GUPPY F-025C
217 GUPPY F-029B
ID (decimal) Camera type
Table 82: Camera type ID list
Configuration of the camera
OSCAR Technical Manual V2.4.0
180
218 GUPPY F-029C
219 GUPPY F-038B
220 GUPPY F-038C
221 GUPPY F-038B NIR
222 GUPPY F-038C NIR
223 GUPPY F-044B NIR
224 GUPPY F-044C NIR
225 GUPPY F-080B BL (board level)
226 GUPPY F-080C BL (board level)
227 GUPPY F-044B
228 GUPPY F-044C
401 STINGRAY F-033B (BL)
402 STINGRAY F-033C (BL)
403 ---
404 ---
405 STINGRAY F-046B (BL)
406 STINGRAY F-046C (BL)
407 STINGRAY F-080B (BL)
408 STINGRAY F-080C (BL)
413 STINGRAY F-145B (BL)
414 STINGRAY F-145C (BL)
415 STINGRAY F-146B (BL)
416 STINGRAY F-146C (BL)
417 STINGRAY F-201B (BL)
418 STINGRAY F-201C (BL)
ID (decimal) Camera type
Table 82: Camera type ID list
Configuration of the camera
OSCAR Technical Manual V2.4.0
181
Advanced feature inquiryThis register indicates with a named bit if a feature is present or not. If a feature is marked as not present the associated register space might not be available and read/write errors may occur.
Note Ignore unnamed bits in the following table: these bits might be set or not.
Configuration of the camera
OSCAR Technical Manual V2.4.0
182
Register Name Field Bit Description
0xF1000040 ADV_INQ_1 MaxResolution [0]
TimeBase [1]
ExtdShutter [2]
TestImage [3]
FrameInfo [4]
Sequences [5]
VersionInfo [6]
--- [7] Reserved
Look-up tables [8]
Shading [9]
DeferredTrans [10]
HDR mode [11] Marlin F-131B/C only
DSNU [12] Marlin F-131B only
Blemish correction [13] Marlin F-131B only
TriggerDelay [14]
Misc. features [15]
Soft Reset [16]
High SNR [17] Oscar only
Color Correction [18]
User profiles [19]
--- [20..21] Reserved
TimeStamp [22] Marlin only
FrmCntStamp [23] Marlin only
TrgCntStamp [24] Marlin only
--- [25..30] Reserved
GP_Buffer [31]
Table 83: Advanced register: Advanced feature inquiry
Configuration of the camera
OSCAR Technical Manual V2.4.0
183
Maximum resolutionThis register indicates the highest resolution for the sensor and is read-only.
0xF1000044 ADV_INQ_2 Input_1 [0]
Input_2 [1]
--- [2] Reserved
--- [3..7] Reserved
Output_1 [8]
Output_2 [9]
--- [10] Reserved
--- [11..15] Reserved
IntEnaDelay [16]
--- [17] Reserved
--- [18..31] Reserved
0xF1000048 ADV_INQ_3 --- [0..31] Reserved
0xF100004C ADV_INQ_4 --- [0..31] Reserved
Note This register normally outputs the MAX_IMAGE_SIZE_INQ Format_7 Mode_0 value.
This is the value given in the specifications tables under Picture size (max.) in Chapter Specifications on page 21.
Register Name Field Bit Description
0xF1000200 MAX_RESOLUTION MaxHeight [0..15] Sensor height(read only)
MaxWidth [16..31] Sensor width(read only)
Table 84: Advanced register: Maximum resolution inquiry
Register Name Field Bit Description
Table 83: Advanced register: Advanced feature inquiry
Configuration of the camera
OSCAR Technical Manual V2.4.0
184
Time baseCorresponding to IIDC, exposure time is set via a 12-bit value in the corre-sponding register (SHUTTER_INQ [51Ch] and SHUTTER [81Ch]).
This means that you can enter a value in the range of 1 to 4095.
Oscar cameras use a time base which is multiplied by the shutter register value. This multiplier is configured as the time base via the TIMEBASE regis-ter.
The time base IDs 0-9 are in bits 28 to 31. See Table 86: Time base ID on page 184.
Default time base is 20 µs: This means that the integration time can be changed in 20 µs increments with the shutter control.
Register Name Field Bit Description
0xF1000208 TIMEBASE Presence_Inq [0] Indicates presence of this feature (read only)
--- [1..27] Reserved
Timebase_ID [28..31] See Table 86: Time base ID on page 184
Table 85: Advanced register: Time base
Note Time base can only be changed when the camera is in idle state and becomes active only after setting the shutter value.
ID Time base in µs Description
0 1
1 2
2 5
3 10
4 20 default value
5 50
6 100
7 200
Table 86: Time base ID
Configuration of the camera
OSCAR Technical Manual V2.4.0
185
Extended shutterThe exposure time for long-term integration of up to 67 seconds can be entered with µs precision via the EXTENDED_SHUTTER register.
The minimum allowed exposure time depends on the camera model. To deter-mine this value write 1 to the ExpTime field and read back the minimum allowed exposure time.
The longest exposure time, 3FFFFFFh, corresponds to 67.11 seconds.
8 500
9 1000
Note The ABSOLUTE VALUE CSR register, introduced in IIDC V1.3, is not implemented.
Register Name Field Bit Description
0xF100020C EXTD_SHUTTER Presence_Inq [0] Indicates presence of this fea-ture (read only)
--- [1.. 5] Reserved
ExpTime [6..31] Exposure time in µs
Table 87: Advanced register: Extended shutter
Note • Exposure times entered via the 81Ch register are mir-rored in the extended register, but not vice versa.
• Changes in this register have immediate effect, even when camera is transmitting.
• Extended shutter becomes inactive after writing to a format / mode / frame rate register.
• Extended shutter setting will thus be overwritten by the normal time base/shutter setting after Stop/Start of FireView or FireDemo.
ID Time base in µs Description
Table 86: Time base ID
Configuration of the camera
OSCAR Technical Manual V2.4.0
186
Test imagesBit [8] to [14] indicate which test images are saved. Setting bit [28] to [31] activates or deactivates existing test images.
Register Name Field Bit Description
0xF1000210 TEST_IMAGE Presence_Inq [0] Indicates presence of this feature (read only)
--- [1..7] Reserved
Image_Inq_1 [8] Presence of test image 10: N/A1: Available
Image_Inq_2 [9] Presence of test image 20: N/A1: Available
Image_Inq_3 [10] Presence of test image 30: N/A1: Available
Image_Inq_4 [11] Presence of test image 40: N/A1: Available
Image_Inq_5 [12] Presence of test image 50: N/A1: Available
Image_Inq_6 [13] Presence of test image 60: N/A1: Available
Image_Inq_7 [14] Presence of test image 70: N/A1: Available
--- [15..27] Reserved
TestImage_ID [28..31] 0: No test image active1: Image 1 active2: Image 2 active…
Table 88: Advanced register: Test image
Configuration of the camera
OSCAR Technical Manual V2.4.0
187
Look-up tables (LUT)Load the look-up tables to be used into the camera and choose the look-up table number via the LutNo field. Now you can activate the chosen LUT via the LUT_CTRL register.
The LUT_INFO register indicates how many LUTs the camera can store and the maximum size of the individual LUTs.
The possible values for LutNo are 0..n-1, whereas n can be determined by reading the field NumOfLuts of the LUT_INFO register.
Register Name Field Bit Description
0xF1000240 LUT_CTRL Presence_Inq [0] Indicates presence of this feature (read only)
--- [1..5] Reserved
ON_OFF [6] Enable/disable this feature
--- [7..25] Reserved
LutNo [26..31] Use look-up table with LutNo number
0xF1000244 LUT_MEM_CTRL Presence_Inq [0] Indicates presence of this feature (read only)
--- [1..4] Reserved
EnableMemWR [5] Enable write access
--- [6..7] Reserved
AccessLutNo [8..15] Reserved
AddrOffset [16..31] byte
0xF1000248 LUT_INFO Presence_Inq [0] Indicates presence of this feature (read only)
--- [1..7] Reserved
NumOfLuts [8..15] Maximum number of look-up tables
MaxLutSize [16..31] Maximum look-up table size (bytes)
Table 89: Advanced register: LUT
Configuration of the camera
OSCAR Technical Manual V2.4.0
188
Shading correctionOwing to technical circumstances, the interaction of recorded objects with one another, optical effects and lighting non-homogeneities may occur in the images.
Because these effects are normally not desired, they should be eliminated as far as possible in subsequent image processing. The camera has automatic shading correction to do this.
Provided that a shading image is present in the camera, the on/off bit can be used to enable shading correction.
The on/off and ShowImage bits must be set for saved shading images to be displayed.
Note Always make sure that the shading image is saved at the highest resolution of the camera. If a lower resolution is cho-sen and ShowImage is set to true, the image will not be dis-played correctly.
Register Name Field Bit Description
0xF1000250 SHDG_CTRL Presence_Inq [0] Indicates presence of this feature (read only)
BuildError [1] Could not built shading image
--- [2..3] Reserved
ShowImage [4] Show shading data as image
BuildImage [5] Build a new shading image
ON_OFF [6] Shading on/off
Busy [7] Build in progress
--- [8..23] Reserved
GrabCount [24..31] Number of images
0xF1000254 SHDG_MEM_CTRL Presence_Inq [0] Indicates presence of this feature (read only)
--- [1..4] Reserved
EnableMemWR [5] Enable write access
EnableMemRD [6] Enable read access
--- [7] Reserved
AddrOffset [8..31] In bytes
Table 90: Advanced register: Shading
Configuration of the camera
OSCAR Technical Manual V2.4.0
189
0xF1000258 SHDG_INFO Presence_Inq [0] Indicates presence of this feature (read only)
--- [1..7] Reserved
MaxImageSize [8..31] Maximum shading image size (in bytes)
Register Name Field Bit Description
Table 90: Advanced register: Shading
Configuration of the camera
OSCAR Technical Manual V2.4.0
190
Frame informationThis register can be used to double-check the number of images received by the host computer against the number of images which were transmitted by the camera. The camera increments this counter with every FrameValid sig-nal. This is a mirror of the frame counter information found at 0xF1000610.
The FrameCounter is incremented when an image is read out of the sensor.
The FrameCounter does not indicate whether an image was sent over the IEEE 1394 bus or not.
Input/output pin control
Register Name Field Bit Description
0xF1000270 FRAMEINFO Presence_Inq [0] Indicates presence of this feature (read only)
ResetFrameCnt [1] Reset frame counter
--- [2..31] Reserved
0xF1000274 FRAMECOUNTER FrameCounter [0..31] Number of captured frames since last reset
Table 91: Advanced register: Frame information
Note • See Chapter Input/output pin control on page 40• See Chapter IO_INP_CTRL 1-2 on page 41• See Chapter IO_OUTP_CTRL 1-2 on page 46• See Chapter Output modes on page 47
Configuration of the camera
OSCAR Technical Manual V2.4.0
191
Delayed Integration Enable (IntEna)A delay time between initiating exposure on the sensor and the activation edge of the IntEna signal can be set using this register. The on/off flag acti-vates/deactivates integration delay. The time can be set in µs in DelayTime.
Note • Only one edge is delayed.• If IntEna_Out is used to control an exposure, it is pos-
sible to have a variation in brightness or to precisely time a flash.
Figure 65: Delayed integration timing
Register Name Field Bit Description
0xF1000340 IO_INTENA_DELAY Presence_Inq [0] Indicates presence of this feature (read only)
--- [1..5] Reserved
ON_OFF [6] Enable/disable integration enable delay
--- [7..11] Reserved
DELAY_TIME [12..31] Delay time in µs
Table 92: Advanced register: Delayed Integration Enable (IntEna)
Configuration of the camera
OSCAR Technical Manual V2.4.0
192
Auto shutter controlThe table below illustrates the advanced register for auto shutter control. The purpose of this register is to limit the range within which auto shutter operates.
When both auto shutter and auto gain are enabled, priority is given to increasing shutter when brightness decreases. This is done to achieve the best image quality with lowest noise.
For increasing brightness, priority is given to lowering gain first for the same purpose.
Auto gain controlThe table below illustrates the advanced register for auto gain control.
Register Name Field Bit Description
0xF1000360 AUTOSHUTTER_CTRL Presence_Inq [0] Indicates presence of this feature (read only)
--- [1..31] Reserved
0xF1000364 AUTOSHUTTER_LO Min Value [0..31] Minimum value
0xF1000368 AUTOSHUTTER_HI Max Value [0..31] Maximum value
Table 93: Advanced register: Auto shutter control
Note • Values can only be changed within the limits of shutter CSR.
• Changes in auto exposure register only have an effect when auto shutter is enabled.
• Auto exposure limits are: 50..205 (SmartView Ctrl1 tab: Target grey level)
Register Name Field Bit Description
0xF1000370 AUTOGAIN_CTRL Presence_Inq [0] Indicates presence of this feature (read only)
--- [1..3] Reserved
MaxValue [4..15] Maximum value
--- [16..19] Reserved
MinValue [20..31] Minimum value
Table 94: Advanced register: Auto gain control
Configuration of the camera
OSCAR Technical Manual V2.4.0
193
MinValue and MaxValue limits the range the auto gain feature is allowed to use for the regulation process. Both values are initialized with the minimum and maximum value defined in the standard GAIN_INQ register.
Changing the auto gain range might not affect the regulation, if the regu-lation is in a stable condition and no other condition affecting the image brightness is changed.
If both auto gain and auto shutter are enabled and if the gain is at its lower boundary and shutter regulation is in progress, decreasing the lower auto gain boundary has no effect on auto gain/shutter regulation as long as auto shutter regulation is active.
Both values can only be changed within the range defined by the standard GAIN_INQ register.
Autofunction AOIThe table below illustrates the advanced register for autofunction AOI.
The possible increment of this work area position and size is 128 pixels. The camera automatically adjusts the settings to permitted values:
Register Name Field Bit Description
0xF1000390 AUTOFNC_AOI Presence_Inq [0] Indicates presence of this feature (read only)
--- [1..3] Reserved
ShowWorkArea [4] Show work area
--- [5] Reserved
ON_OFF [6] Enable/disable AOI (see note above)
--- [7..31] Reserved
0xF1000394 AF_AREA_POSITION Left [0..15] Work area position(left coordinate)
Top [16..31] Work area position(top coordinate)
0xF1000398 AF_AREA_SIZE Width [0..15] Width of work area size
Height [16..31] Height of work area size
Table 95: Advanced register: Autofunction AOI
Region Permitted values
Left, top 0, 128, 256, 384, 512, 768, 1024…
Width, height 128, 256, 384, 512, 768, 1024…
Table 96: Permitted values for AF_AREA_SIZE
Configuration of the camera
OSCAR Technical Manual V2.4.0
194
Due to the fact that the active image size might not be divisible by 128 with-out a remainder, the auto function AOI work area size might be greater.
This allows for the positioning of the work area to be at the bottom of the active image.
E.g. if the active image size is 640 x 480 pixel the camera accepts a maximum of 640 x 512 pixel as the auto function AOI work area (if the control area position is 0:0).
Another case is for outdoor applications: the sky will be excluded from the generation of the reference levels, when the autofunction AOI is placed at the bottom of the image.
Note If the adjustment fails and the work-area size and/or posi-tion becomes invalid, this feature is automatically switched off. Make sure to read back the ON_OFF flag, if this feature doesn't work as expected.
Configuration of the camera
OSCAR Technical Manual V2.4.0
195
Color correctionTo switch off color correction in YUV mode: see bit [6]
Trigger delay
The advanced register allows start of the integration to be delayed via DelayTime by max. 221 µs, which is max. 2.1 s after a trigger edge was detected.
Register Name Field Bit Description
0xF10003A0 COLOR_CORR ON_OFF [6] Color correction on/off
default: on
Write: 02000000h to switch color correction OFF
Write: 00000000h to switch color correction ON
Table 97: Advanced register: Color correction
Register Name Field Bit Description
0xF1000400 TRIGGER_DELAY Presence_Inq [0] Indicates presence of this feature (read only)
--- [1..5] Reserved
ON_OFF [6] Trigger delay on/off
--- [7..10] Reserved
DelayTime [11..31] Delay time in µs
Table 98: Advanced register: Trigger delay
Configuration of the camera
OSCAR Technical Manual V2.4.0
196
Mirror imageThe table below illustrates the advanced register for Mirror image.
Soft Reset
The SOFT_RESET feature is similar to the INITIALIZE register, with the follow-ing differences:• 1 or more bus resets will occur.• The FPGA will be rebooted.
The reset can be delayed by setting the Delay to a value unequal to 0.
The delay is defined in 10 ms steps.
Register Name Field Bit Description
0xF1000410 MIRROR_IMAGE Presence_Inq [0] Indicates presence of this feature (read only)
--- [1..5] Reserved
ON_OFF [6] Mirror image on/off
1: on0: off
Default: off
--- [7..31] Reserved
Table 99: Advanced register: Mirror
Register Name Field Bit Description
0xF1000510 SOFT_RESET Presence Inquiry [0] Indicates presence of this feature (read only)
--- [1..5] Reserved
Reset [6] Initiate reset
--- [7..19] Reserved
Delay [20..31] Delay reset in 10 ms steps
Table 100: Advanced register: Soft reset
Note When SOFT_RESET has been defined, the camera will respond to further read or write requests, but will not process them.
Configuration of the camera
OSCAR Technical Manual V2.4.0
197
High SNR mode (High Signal Noise Ratio)With High SNR mode enabled the camera internally grabs GrabCount images and outputs a single averaged image.
Register Name Field Bit Description
0xF1000520 HIGH_SNR Presence_Inq [0] Indicates presence of this feature (read only)
--- [1..5] Reserved
ON_OFF [6] High SNR mode on/off
--- [7..22] Reserved
GrabCount [23..31] Number of images
Table 101: Advanced register: High Signal Noise Ratio (HSNR)
Configuration of the camera
OSCAR Technical Manual V2.4.0
198
User profilesDefinition Within the IIDC specification user profiles are called memory channels.
Often they are called user sets. In fact these are different expressions for the following: storing camera settings into a non-volatile memory inside the camera.
From firmware 3.04 onwards, Oscar cameras can store up to three user pro-files (plus the factory default) in the camera in a non-volatile memory.
User profiles can be programmed with the following advanced feature regis-ter:
In general this advanced register is a wrapper around the standard memory channel registers with some extensions. In order to query the number of available user profiles please check the Memory_Channel field of the BASIC_FUNC_INQ register at offset 0x400 (see IIDC V1.3x for more details).
The ProfileID is equivalent to the memory channel number and specifies the profile number to store settings to or to restore settings from. In any case profile #0 is the hard-coded factory profile and cannot be overwritten.
After an initialization command, startup or reset of the camera, the ProfileID also indicates which profile was loaded on startup, reset or initialization.
Register Name Field Bit Description
0xF1000550 USER_PROFILE Presence_Inq [0] Indicates presence of this feature (read only)
--- [1..7] Reserved
SaveProfile [8] Save settings to profile
RestoreProfile [9] Load settings from profile
SetDefaultID [10] Set profile ID as default
--- [11..19] Reserved
ErrorCode [20..23] Error code
See Table 103: User profile: Error codes on page 199
--- [24..27] Reserved
ProfileID [28..31] ProfileID (memory channel)
Table 102: Advanced register: User profiles
Note • The default profile is the profile that is loaded on power-up or an INITIALIZE command.
• A save or load operation delays the response of the camera until the operation is completed. At a time only one operation can be performed.
Configuration of the camera
OSCAR Technical Manual V2.4.0
199
Store To store the current camera settings into a profile:
1. Write the desired ProfileID with the SaveProfile flag set.
2. Read back the register and check the ErrorCode field
Restore To restore the settings from a previous stored profile:
1. Write the desired ProfileID with the RestoreProfile flag set.
2. Read back the register and check the ErrorCode field.
Set default To set the default profile to be loaded on startup, reset or initialization:
1. Write the desired ProfileID with the SetDefaultID flag set.
2. Read back the register and check the ErrorCode field.
Factory default To go back to the factory default profile:
1. Select ProfileID = 0 and toggle the SetDefaultID flag set.
2. Read back the register and check the ErrorCode field.
Error codes
Reset of error codes
The ErrorCode field is set to zero on the next write access.
To reset the ErrorCode manually:
1. Write 00000000h to the USER_PROFILE register.
Stored settings
The following table shows the settings stored inside a profile:
Error code # Description
0x00 No error
0x01 Profile data corrupted
0x02 Camera not idle during restore operation
0x03 Feature not available (feature not present)
0x04 Profile doesn’t exist
0x05 ProfileID out of range
0x06 Restoring the default profile failed
0x07 Loading LUT data failed
0x08 Storing LUT data failed
Table 103: User profile: Error codes
Configuration of the camera
OSCAR Technical Manual V2.4.0
200
The user can specify which one will be loaded upon startup of the camera.
This frees the user software from having to restore camera settings, that dif-fer from default, after every startup. This can be especially helpful if third party software is used which may not give easy access to certain advanced features or may not provide efficient commands for quick writing of data blocks (e.g. for a LUT) into the camera.
Advanced registers
TIMEBASEEXTD_SHUTTERIO_INP_CTRLIO_OUTP_CTRLIO_INTENA_DELAYAUTOSHUTTER_LOAUTOSHUTTER_HIAUTOGAIN_CTRLAUTOFNC_AOICOLOR_CORRTRIGGER_DELAYMIRROR_IMAGEHIGH_SNRLUT_CTRLLUT_DATA
Table 104: User profile: stored settings
Note • A profile save operation automatically disables captur-ing of images.
• A profile save or restore operation is an uninterruptable (atomic) operation: The write response (of the asyn-chronous write cycle) will be sent after completion of the operation.
• Restoring a profile will not overwrite other settings than listed above.
• If a restore operation fails or the specified profile does not exist, all registers will be overwritten with the hard-coded factory defaults (profile #0).
• Data written to this register is not reflected in the standard memory channel registers.
Configuration of the camera
OSCAR Technical Manual V2.4.0
201
GPDATA_BUFFERGPDATA_BUFFER is a general purpose register that regulates the exchange of data between camera and host for:• writing look-up tables (LUTs) into the camera• uploading/downloading of the shading image
GPDATA_INFO Buffer size query
GPDATA_BUFFER indicates the actual storage range
Little endian vs. big endian byte order• Read/WriteBlock accesses to GPDATA_BUFFER are recommended, to read
or write more than 4 byte data. This increases the transfer speed com-pared to accessing every single quadlet.
• The big endian byte order of the 1394 bus is unlike the little endian byte order of common operating systems (Intel PC). Each quadlet of the local buffer, containing the LUT data or shading image for instance, has to be swapped bytewise from little endian byte order to big endian byte order before writing on the bus.
Register Name Field Bit Description
0xF1000FFC GPDATA_INFO --- [0..15] Reserved
BufferSize [16..31] Size of GPDATA_BUFFER (byte)
0xF1001000
…
0xF10017FC
GPDATA_BUFFER
Table 105: Advanced register: GPData buffer
Note • Read the BufferSize before using.• GPDATA_BUFFER can be used by only one function at a
time.
Bit depth little endian big endian Description
8 bit L0 L1 L2 L3 L3 L2 L1 L0 L: low byte
H: high byte16 bit L0 H0 L1 H1 H1 L1 H0 L0
Table 106: Swapped first quadlet at address offset 0
Firmware update
OSCAR Technical Manual V2.4.0
202
Firmware update
Firmware updates can be carried out without opening the camera.
You need:• Programming cable E 1000666• Software AVTCamProg• PC or laptop with serial interface (RS 232)• Documentation for firmware update
Please contact your local dealer for further information.
Note Only Oscar F-810C: cameras with a serial number SN 50675733 (or higher) or with production date 26 April 2005 (or later) can be updated with microcontroller firmware 3.04/ FPGA firmware 1.06. (Cameras must have a FIFO mem-ory of 64 MB. SmartView Adv 1 tab FIFO size must be 3.)
Note Older versions have to be updated at the AVT factory.
Appendix
OSCAR Technical Manual V2.4.0
203
Appendix
Sensor position accuracy of AVT cameras
Figure 66: AVT sensor position accuracy
x
ycamera body
sensor case
pixel area
x
ycamera body
sensor case
pixel area
sensor case
camera body
pixel area
sensor case
camera body
pixel area
AVT Guppy Series
Method of Positioning: Automated mechanical alignment of sensor into camera front module. (lens mount front flange)
Reference points: Sensor: Center of pixel area (photo sensitive cells). Camera: Center of camera front flange (outer case edges).
Accuracy: x/y: +/- 0.25mm (Sensor shift) z: +50 / -100μm (for SN > 84254727, optical back focal length) +0 / -100μm (for SN > 252138124, optical back focal length)
: +/- 1° (Sensor rotation)
AVT Marlin, Oscar, Dolphin, Pike, Stingray
Method of Positioning: Optical alignment of photo sensitive sensor area into camera front module. (lens mount front flange)
Reference points: Sensor: Center of pixel area (photo sensitive cells). Camera: Center of camera front flange (outer case edges).
Accuracy: x/y: +/- 0.1mm (Sensor shift) z: +0 / -50μm (Optical back focal length)
: +/- 0.5° (Sensor rotation)
Note: x/y - tolerances between c-Mount hole and pixel area may be higher.
OSCAR Technical Manual V2.4.0
204
Index
Index
Numbers
0xF0F00830 (bulk trigger) ........................1030xF1000010 (version info) .......................1770xF1000040 (advanced feature inquiry)......1820xF1000200 (max. resolution) ..................1830xF1000208 (time base) ..........................1840xF100020C (extended shutter)..........112, 1850xF1000210 (test image) .........................1860xF1000240 (LUT)...................................1870xF1000250 (shading) .............................1880xF1000260 (deferred image transport)......1180xF1000270 (frame info)..........................1900xF1000274 (frame counter).....................1900xF1000300 (input control)....................... 400xF1000340 (Delayed IntEna) ...................1910xF1000360 (auto shutter control) ............1920xF1000370 (auto gain control) ................1920xF1000390 (autofunction AOI) ................1930xF10003A0 (color correction) ..................1950xF1000400 (trigger delay) ......................1950xF1000410 (mirror image) ......................1960xF1000510 (soft reset)...........................1960xF1000520 (High SNR) ...........................1970xF1000550 (user profiles/memory channels/user sets) ..............................................1980xF1000FFC (GPData buffer)......................2012 out of 4 H+V sub-sampling (color)
drawing ............................................ 892 x full binning
drawing ............................................ 872 x horizontal binning
drawing ............................................ 862 x vertical binning
drawing ............................................ 85
A
Abs_Control (Field) .............. 60, 65, 66, 68, 70Abs_Control_Inq (Field) ............................ 42Access_Control_Register ..........................164accuracy
sensor position .................................203ActivVision Tools ..................................... 74AddrOffset ......................................187, 188
Advanced feature inquiry .........................181Advanced feature inquiry register ..............182Advanced features...................................175
activate ...........................................177base address.....................................164inquiry.............................................162
advanced registerAuto gain control ..............................192Auto shutter control ..........................192Autofunction AOI .......................193, 195Deferred image transport ....................118Delayed Integration Enable (IntEna) ....191Frame information .............................190GPData buffer ...................................201High SNR .........................................197LUT .................................................187Max. resolution .................................183Mirror image.....................................196Output control ................................... 46Soft reset .........................................196Test images ......................................186Trigger delay ....................................195User profiles .....................................198version information ...........................177
AF_AREA_SIZElegal values ......................................193
Algorithmcorrection data .................................. 75
amplification........................................... 59analog color signal................................... 59Analog Devices ........................................ 59AOI..................................................76, 129
correction data .................................. 76area of interest (AOI) ............................... 76Asynchronous broadcast...........................115auto exposure
limits ..............................................192target grey level...........................67, 192
Auto Exposure (CSR register) ..................... 66auto gain..........................................65, 192Auto gain control (advanced register) ........192auto shutter.................................63, 69, 192Auto shutter control (advanced register) ....192AUTOFNC_AOI....................................63, 193
OSCAR Technical Manual V2.4.0
205
Index
AUTOFNC_AOI positioning ......................... 63Autofunction AOI (advanced register) .193, 195AUTOGAIN_CTRL......................................192automatic generation
correction data .................................. 75Automatic White Balance (AWB)................. 63AUTO_EXPOSURE ...................................... 66Auto_Inq ................................................ 42AVT sensor position accuracy ....................203AVTCamProg ...........................................202AWB....................................................... 63A_M_MODE (Field)................ 60, 65, 66, 68, 70
B
bandwidth .............................................120affect frame rate ...............................142available ..........................................132deferred image transport ....................117FastCapture ......................................119frame rates.......................................131limitation of IEEE 1394 bus.................135RGB8 format ...................................... 93save in RAW-mode .............................. 90
BAYER demosaicing .................................. 91BAYER mosaic.......................................... 90Bayer to RGB
color interpretation ............................ 90binning .................................................. 84
full................................................... 87horizontal ......................................... 86vertical ............................................. 85
black level .............................................. 67black value ........................................ 64, 67blink codes ............................................. 38block diagram
AFE .................................................. 59Oscar cameras .................................... 52
block diagramscameras ............................................ 52
BRIGHTNESS......................................68, 169Brightness
inquiry register .................................163brightness
auto shutter ...................................... 69average............................................. 65decrease ..........................................192IIDC register ...................................... 68increase ......................................64, 192
level................................................. 74LUT .................................................. 71nonlinear .......................................... 71reference ..................................... 65, 69setting ............................................. 67variation ..........................................191
Brightness Control ..................................163Brightness (CSR register) .......................... 68BRIGHTNESS_INQUIRY .............................165Brightness_inq. ......................................165buffer
LUT .................................................. 73bulk trigger.....................................100, 102Busy signal ............................................. 44Bus_Id ..................................................145
C
Cable GND............................................... 35camera dimensions................................... 29camera interfaces..................................... 35camera lenses.......................................... 20cameras
block diagram .................................... 52Camera_Status_Register ...........................145CDS........................................................ 59CE ......................................................... 18channel .................................................. 49Color correction ...................... 90, 92, 93, 195
YUV mode ......................................... 93color correction
AVT cameras ...................................... 92why? ................................................ 92
Color Correction (Field)............................182color information..................................... 90Color interpolation................................... 91Com (LED state)....................................... 37common GND
inputs............................................... 36common vcc
outputs............................................. 36controlling
image capture...................................100correction data
algorithm.......................................... 75AOI .................................................. 76automatic generation.......................... 75requirements ..................................... 75shading ............................................ 74
OSCAR Technical Manual V2.4.0
206
Index
correlated double sampler ......................... 59CSR.......................................................145CSR register
Auto Exposure.................................... 66Brightness......................................... 68GAIN ................................................ 65
D
data block packet format........................... 49description ........................................ 49
data exchange bufferLUT .................................................. 73
data packets ........................................... 49data path................................................ 52data payload size ....................................142data_length ............................................ 49DCAM ........................................16, 120, 145declaration of conformity .......................... 18deferred image transport..........................117Deferred image transport (advanced register)....118Delayed Integration Enable (IntEna) (advancedregister) ................................................191Digital Camera Specification .....................145digital video information .......................... 49digitization............................................. 59digitizer ................................................. 72document history....................................... 9DSNU
horizontal mirror function.................... 83
E
E 1000666 .............................................202edge mode (Trigger_Mode_0)....................100End of exposure ......................................114error code
user profiles .....................................199error codes
LED .................................................. 38error states ............................................. 38Exposure time
(Field) .............................................112exposure time.........................................111
81 Ch register ...................................112example ...........................................111extended shutter ...............................185formula............................................111
longest ............................................112long-term integration ........................112minimum .........................................111
ExpTime (Field) ......................................112EXTD_SHUTTER .......................................185extended shutter ....................................112
configuration....................................112FireDemo..........................................185FireView...........................................185inactive .................................... 112, 185register............................................185Trigger mode ....................................100trigger mode ....................................100
EXTENDED_SHUTTER ................................112External GND........................................... 36external trigger ....................................... 39
F
FastCapturebandwidth........................................119false................................................119only Format_7 ..................................119
FastCapture (Field)..................................118FCC Class B.............................................. 18FireDemo
Extended shutter...............................185FirePackage
OHCI API software .............................. 16FireView
Extended shutter...............................185firmware update .............................. 202, 203focal length ............................................ 20
O-F320C ............................................ 20Oscar F-510C...................................... 20
FORMAT_7_ERROR_1................................. 38FORMAT_7_ERROR_2................................. 38FOV........................................................ 83FPGA...................................................... 59FPGA boot error ....................................... 38Frame information (advanced register).......190frame rates
bandwidth........................................131bandwidth limitation .........................135bus speed.........................................120Format_7 .........................................135Marlin models ...................................120maximum .........................................120tables ..............................................131
OSCAR Technical Manual V2.4.0
207
Index
video mode 0....................................135video mode 2....................................135
Frame valid ............................................. 44FrameCounter .........................................190free-run.................................................115Full binning ............................................ 87Fval ....................................................... 44Fval signal .............................................. 44
G
GainPixel Gain Amplifier ............................ 59
gainauto ................................................. 65auto exposure CSR .............................. 65AUTOFNC_AOI .................................... 63formula............................................. 67manual ............................................. 64manual gain range.............................. 64ranges .............................................. 64white balance .................................... 59
gain CSR................................................. 67GAIN (CSR register) .................................. 65GAIN (Name)........................................... 65GAIN (register) ........................................ 61gamma function ...................................... 71
CCD models........................................ 76Gamma LUT ............................................. 71global shutter.........................................100GND for RS232......................................... 36GPData buffer (advanced register) .............201GPDATA_BUFFER ............................ 73, 81, 82GRAB_COUNT...................................... 75, 76
H
hardware trigger ................................43, 106HDR mode..............................................182High SNR (advanced register) ...................197HoldImg
field ................................................118flag .................................................118mode...............................................118
HoldImg (Field) ......................................118Horizontal binning ................................... 86horizontal mirror function ......................... 83hue
offset ............................................... 93
I
IEEE 1394 ............................................... 16declaration of conformity .................... 18
IEEE 1394 portpin assignment .................................. 35
IEEE 1394 Trade Association.....................145IEEE 1394a connector............................... 35IIDC..........................................16, 120, 145
data structure .................................... 51isochronous data block packet format.... 49pixel data.......................................... 49trigger delay...................................... 42video data format............................... 50Y16 .................................................. 50Y8.................................................... 50YUV 4:1:1.......................................... 50YUV 4:2:2.......................................... 50
IIDC V1.3...............................................100image capture
controlling .......................................100IMAGE_POSITION ....................................129IMAGE_SIZE ...........................................129input
block diagram .................................... 39configuration register ......................... 40current status .................................... 41high active........................................ 41low active ......................................... 41polarity setting .................................. 47Trigger (Mode) ................................... 41
input mode ............................................. 41input pin control ..................................... 41InputMode (Field) .................................... 40inputs
common GND ..................................... 36general ............................................. 39ID .................................................... 41in detail............................................ 39inverting........................................... 39triggers............................................. 39
input/output pin control..........................190Inquiry register
basic function...................................162Integration Enable Signal.......................... 44IntEna.................................................... 36IntEna signal ....................................44, 191internal trigger................................100, 102interpolation
OSCAR Technical Manual V2.4.0
208
Index
BAYER demosaicing ............................ 91Bayer demosaicing.............................. 91Bayer to RGB ..................................... 90color ........................................... 90, 91
IO_INP_CTRL1 ......................................... 40IO_INP_CTRL2 ......................................... 40IO_OUTP_CTRL1 ....................................... 46IO_OUTP_CTRL2 ....................................... 46isochronous blocks ................................... 49isochronous channel number ..................... 49isochronous data block packet format ......... 49isochronous data packets .......................... 49IsoEnable
white balance .................................... 62ISO_Enable ............................................115ISO_Enable mode ....................................115Iso_Enable mode
multi-shot ........................................115one-shot ..........................................113
J
jitter ..............................................114, 116at exposure start ...............................117
L
LEDCom ................................................. 37error codes ........................................ 38indication ......................................... 37on (green)......................................... 37status ............................................... 37Trg ................................................... 37yellow............................................... 37
Legal notice .............................................. 2legal values
AF_AREA_SIZE...................................193level mode (Trigger_Mode_1)....................100Look Up Table (LUT) ................................. 71Look Up Tables (LUT)...............................187look-up table (LUT)
user-defined ...................................... 71LUT.......................................................187
data exchange buffer .......................... 73example ............................................ 71Gamma ............................................. 71general ............................................. 71loading into camera............................ 73
volatile ............................................. 72LUT (advanced register) ...........................187LutNo....................................................187LUT_CTRL...............................................187LUT_INFO ..............................................187LUT_MEM_CTRL.......................................187
M
Manual_Inq............................................. 42Maximum resolution (Register) .................183MaxLutSize (Field) ..................................187MaxResolution (Field) ..............................182MaxValue ...............................................193Max. resolution (advanced register) ...........183MAX_RESOLUTION ...................................183Max_Value .............................................. 42memory channels ....................................198MinValue ...............................................193Min_Value............................................... 42mirror function
horizontal ......................................... 83Mirror image (advanced register)...............196MSB aligned............................................ 50multi-shot .............................................115
external trigger.................................115Trigger_Mode_15...............................102
MVTEC .................................................... 74
N
No DCAM object ....................................... 38No FLASH object ...................................... 38Node_Id ................................................145non-uniform illumination .......................... 74NumOfLuts .............................................187NumOfLuts (Field) ...................................187
O
OFFSETautomatic white balance ..................... 61
offset800h ................................................ 68CCD .................................................. 67configuration ROM.............................148factors.............................................148formula............................................. 67hue .................................................. 93initialize register...............................151
OSCAR Technical Manual V2.4.0
209
Index
inquiry register video format ...............151inquiry register video mode.................152saturation ......................................... 93setting brightness .............................. 67setting gain....................................... 64
OHCI APIFirePackage ....................................... 16
One-Shotvalues..............................................113
oneshotusing Trigger_Mode_15 ......................104
one-shot................................................113Trigger_Mode_15........................100, 102using Trigger_Mode_15 ......................104
one-shot bit...........................................113one-shot mode .......................................113One_Push (Field) ................. 60, 65, 66, 68, 70One_Push_Inq ......................................... 42ON_OFF .................................................. 42ON_OFF (Field) ........................................ 60Oscar cameras ......................................... 17
block diagram .................................... 52Oscar F-320C (specification) ...................... 21Oscar F-510C (specification) ...................... 23Oscar F-810C ........................................... 20Oscar F-810C (specification) ...................... 25Oscar W270 ............................................. 31Oscar W90............................................... 30output
block diagram .................................... 45signals.............................................. 44
Output control (advanced register) ............. 46output mode ........................................... 46
ID .................................................... 47Output mode (Field) ................................. 46output pin control ................................... 47outputs .................................................. 44
common vcc ...................................... 36general ............................................. 39registers ........................................... 46set by software .................................. 48
OutVCC ................................................... 36
P
packet format.......................................... 49PI controller............................................ 65pin control.............................................190PinState flag ........................................... 46
PinState (Field) ....................................... 40plus integral controller ............................. 65polarity flag ............................................ 46Polarity (Field) ................................... 40, 46power
GND ................................................. 36IEEE-1394 pin assignment ................... 35LED .................................................. 37
Presence_Inq .......................................... 40Presence_Inq (Field) ........................... 42, 60programmable mode (Trigger_Mode_15) .....100programming cable
E 1000666........................................202PxGA...................................................... 59PxGA®.................................................... 59
R
Readout_Inq ........................................... 42register .................................................. 60Register mapping..................................... 38Requirements
correction data .................................. 75RGB to YUV
formula............................................. 93RGB8 format ........................................... 93RoHS (2002/95/EC).................................. 18RS232 .................................................... 36
serial interface..................................202RxD_RS232 ............................................. 36
S
saturationoffset ............................................... 93
sensorpositioning ....................................... 29
sensor position accuracy ..........................203sequence
automatic white balance ..................... 62BAYER color pattern............................ 59commands for generating shading image 76correction ......................................... 76deferred mode ..................................119loading a LUT .................................... 73OneShot...........................................113white balance .................................... 62
sequence controlcorrection data .................................. 76
OSCAR Technical Manual V2.4.0
210
Index
serial interfaceRS 232.............................................202
shaded image .......................................... 78shading
correction data .................................. 74shading correction .............................74, 188shading image......................................... 74
automatic generation.......................... 75delay ................................................ 76Format_7 .......................................... 76generate ........................................... 76generation ........................................ 77load into camera ................................ 82load out of camera ............................. 81
shading images ......................................188shading reference image ........................... 75SHDG_CTRL .......................................76, 188SHDG_INFO ............................................189SHDG_MEM_CTRL.....................................188SHUTTER................................................. 70Shutter CSR............................................. 70shutter time
formula............................................111SHUTTER_MODES .....................................100signal-to noise ratio (SNR)
vertical binning.................................. 85signal-to-noise ratio (SNR)........................ 84signal-to-noise separation......................... 84SmartView............................................... 16SNR ....................................................... 84Soft reset (advanced register) ...................196specification
Oscar F-320C...................................... 21Oscar F-510C...................................... 23Oscar F-810C...................................... 25
specifications.......................................... 21spectral sensitivity
Oscar F-320C...................................... 27Oscar F-510C...................................... 27Oscar F-810C...................................... 28
spectral transmissionIR cut filter ....................................... 19Jenofilt 217....................................... 19
split shutter (frame readout) ..................... 57split shutter (shutter mode) .....................108Stack setup ............................................. 38Stack start .............................................. 38standard housing ..................................... 29status LED............................................... 37
stored settingsuser profile.......................................200
strobe flash............................................. 44styles ..................................................... 14sub-sampling .......................................... 88
definition.......................................... 88sy (sync bit) ........................................... 49symbols.................................................. 14sync bit (sy) ........................................... 49synchronization value (sync bit) ................ 49system components.................................. 19
T
tag field ................................................. 49target grey level
corresponds to Auto_exposure.............170Target grey level (auto exposure) .........67, 192Target grey level (SmartView)
corresponds to auto exposure............... 69tCode ..................................................... 49test image .............................................143
configuration register ........................186save ................................................186
Test images (advanced register) ................186TEST_IMAGE ...........................................186tg.......................................................... 49time base
exposure time...................................111Oscar F-510C.....................................111setting ............................................185trigger delay.....................................105
time base ID ..........................................184time base (Register)................................184time response.........................................113TIMEBASE ....................................... 175, 184timebase
trigger delay...................................... 42TimeBase (Field) .....................................182TPA- ...................................................... 35TPA+...................................................... 35TPB- ...................................................... 35TPB+...................................................... 35transaction code (tCode)........................... 49Trg (LED state) ........................................ 37trigger
bulk ......................................... 100, 102control image capture ........................100delay ........................................... 42, 48
OSCAR Technical Manual V2.4.0
211
Index
edge................................................. 43external ......................................37, 100hardware.....................................43, 106impulse............................................113internal ....................................100, 102latency time .....................................116microcontroller .................................114one-shot ..........................................113signal ............................................... 39software...........................................115synchronize ......................................116
trigger delay ..........................................105advanced CSR...............................43, 106advanced register .........................43, 106off ................................................... 43on.................................................... 43
Trigger Delay CSR ..................................... 43trigger delay CSR ....................................106Trigger delay inquiry register ....................105trigger delay inquiry register ..................... 42Trigger delay (advanced register) ..............195trigger function ......................................103Trigger modi ..........................................100triggers .................................................. 39
input ................................................ 39TRIGGER_DELAY .................................43, 106TRIGGER_DELAY_INQUIRY....................42, 105TRIGGER_MODE .......................................103Trigger_Mode .........................................103Trigger_Mode_0 .................................44, 100Trigger_Mode_0 (edge mode)....................100Trigger_Mode_1 ......................................100Trigger_Mode_1 (level mode)....................100Trigger_Mode_15 .............................100, 102Trigger_Mode_15 (programmable mode) .....100Trigger_Polarity ......................................103Trigger_Source .......................................103Trigger_Value .........................................103Tripod adapter......................................... 32Tripod dimensions.................................... 32
U
UNIT_POSITION_INQ................................129UNIT_SIZE_INQ.......................................129user profile
stored settings..................................200user profiles ...........................................198
error code ........................................199
User profiles (advanced register) ...............198user sets................................................198U/B_Value (Field) .................................... 60U/V slider range ...................................... 61
V
valid valuesAF_AREA_SIZE ..................................193
Vendor unique Features............................162version information (advanced register) .....177Vertical binning....................................... 85vertical binning
SNR.................................................. 85video data format
IIDC 1.3............................................ 50Video data payload .................................. 49video format
available bandwidth...........................131frame rate ........................................131
video formats .........................................120Oscar F-320C.....................................121Oscar F-510C.............................. 123, 124Oscar F-810C.....................................127
video Format_7AOI .................................................129
video information .................................... 49video mode
CUR-V-MODE .....................................167Format_7 .........................................173inquiry register .................................152
video mode 0 .........................................135video mode 2 .........................................135VMode_ERROR_STATUS.............................. 38V/R_Value (Field)..................................... 60
W
white balance.......................................... 60auto gain feature ............................... 65auto shutter ...................................... 69AUTOFNC_AOI .................................... 63automatic .................................... 59, 61automatic sequence............................ 62conditions......................................... 61FPGA ................................................ 59general ............................................. 59manual ............................................. 59one push automatic ............................ 61
OSCAR Technical Manual V2.4.0
212
Index
register............................................. 60register 80Ch ..................................... 60six frames ......................................... 61trigger .............................................. 62
WHITE_BALANCE ............................ 60, 61, 62www.alliedvisiontec.com...................... 16, 17