Automatische Erstellung der Preisliste · Our simple but powerful protocol is supported by all...

Interfaces, software and service for the connection of more than 2.000 measurement devices and data sources to over 50 software packages for quality assurance, statistics, and production control.

Product survey 2019 (Valid from 01.08.2019 until 31.12.2019)

SSTTEEIINNWWAALLDD Your specialist for measurement and quality assurance

STEINWALD datentechnik GmbH • Oskar-Loew-Str. 12 • D-95615 Marktredwitz •

Tel. +49 9231 9630-10 • Fax –11 • [email protected]

Product survey 2019

Rev. 31/2019 of 37

1. Table of Contents

1. TABLE OF CONTENTS ......................................................................................................................... 2 2. OVERVIEW ............................................................................................................................................ 3

3. ORDER INFORMATION DC-HI-NET "IW" ............................................................................................. 8

4. PRODUCT SURVEY DC-HI-NET "IW" ................................................................................................... 9

5. ORDER INFORMATION DC-HI-NET "BT" ........................................................................................... 10

6. PRODUCT SURVEY DC-HI-NET "BT"................................................................................................. 11

7. ORDER INFORMATION DC-HI-NET "RADIO" .................................................................................... 13

8. PRODUCT SURVEY DC-HI-NET "RADIO" .......................................................................................... 14

9. ORDER INFORMATION DC-HI-NET "SINGLE X-K" ............................................................................ 16

10. PRODUCT SURVEY DC-HI-NET "SINGLE X-K" ................................................................................. 17

11. ORDER INFORMATION DC-HI-NET "SINGLE X-USB" ....................................................................... 18

12. PRODUCT SURVEY DC-HI-NET "SINGLE X-USB" ............................................................................ 19 13. ORDER INFORMATION DC-HI-NET "SINGLE X-RS" ......................................................................... 21

14. PRODUCT SURVEY DC-HI-NET "SINGLE X-RS" ............................................................................... 22

15. ORDER INFORMATION DC-HI-NET "SINGLE IPX-RS" ...................................................................... 23

16. PRODUCT SURVEY DC-HI-NET "SINGLE IPX-RS" ............................................................................ 24

17. CONTROL ELEMENTS FOR DATA CAPTURE ................................................................................... 25

18. CABLE BETWEEN "DC-HI-NET" AND HOST COMPUTER ................................................................ 25

19. CONNECTION BETWEEN MEASUREMENT DEVICES AND "DC-HI-NET" ........................................ 26

20. SOFTWARE TOOLS ............................................................................................................................ 27

21. SERVICES ........................................................................................................................................... 28

22. TERMS AND CONDITIONS ................................................................................................................. 29

23. LIST OF MEASUREMENT DEVICES ................................................................................................... 31

Product survey 2019

Rev. 31/2019 of 37

2. Overview STEINWALD interface devices adapt your whole measurement and interface collection to one single interface. Our simple but powerful protocol is supported by all leading software packages for quality assurance and production control on PCs and workstations. Independent from measurement devices and software suppli-ers you select your appropriate solution for process control. The advantage: Complicated driver installations and conflicts with other system components (like with PC slot cards) are avoided. You get a secure solution which is easy to install and to extend. Components for wireless measurement data logging as well as software tools complete the product range.

DC-HI-NET connects measurement devices, stored-program controllers and machines from the follow-ing manufacturers: A&D • AEROEL • Agilent • Ahlborn • Ahotec • Akashi • Alluris • Althen • Ametec • Ateq • Atlas Copco • ATORN • Avery Berkel • Bahco • Balluff • Bareiss • Beta Lasermike • Bizerba • Böhm • Bosch • Bowers • Burster • BÜ-TEC • Byk-Gardner • Caliper • Chatillon • CMC-KUHNKE • ColorLite • Datacolor • DeFelsko • Delcam • Deltronic • Denver In-strument • DEPRAG • Desoutter • Karl Deutsch • Diatest • Dini Argeo • Easydur • Edmunds Gages • Elcometer • El-ektro-Physik • Elgo • EmcoTest • Erichsen • Ernst • ESI • ESITRON • FAGOR • Faro • Feinmess Suhl • Fischer • Fluke • FORM+TEST • Fowler • Frank • JW Froehlich • Furness Controls • Garant • General Inspection • Gigahertz-Optik • Gossen-Metrawatt • Gretac Macbeth • Grundig • Hameg • HBM • Hegewald & Peschke • Heidenhain • Helios-Preisser • Hengstler • Hewlett Packard • Hexagon • Hirt • Hommel-Etamic • Imada • Induk • Instron • IST • Jenoptik • KB Prüftechnik • Keithley • Kern • Keyence • Kistler • Knäbel • Konica-Minolta • Kordt • Krautkramer • Kroeplin • Krüss • Dr. Lange • Leybold • Lloyd • Lorentzen & Wettre • Lorenz Messtechnik • L.O.T. • Magnescale • MAGNET-PHYSIK Dr. Steingroever • Mahr • MARK-10 • Marposs • Marui-Keiki • MAV • Mavomatic • Mecmesin • Megatron • Mercer • MetLogix • Metrohm • Metronics • Mettler Toledo • Micro Epsilon • MicroStudio • MicroVu • Mitutoyo • Newport • Nieberding • Nikon • OBLF • OGP • Ohaus • OKM • Olympus • Panametrics • PAV • PCE • Pfeiffer Vacuum • Phynix • Precisa • Precitec • Qness • Raytek • Reicherter • Rhewa • Röntgenanalytik • RSF • Saltus • Sartorius • Sauter • Scal-tec • Schatz • Schenck • Schleich • Dr. Schneider • Sensor Instruments • Shimadzu • Shimpo • Siemens • Siko • Si-kora • SIP • Soehnle • Solartron • Solex • Sony • SOURCETRONIC • Stanley • Stiefelmayer • Stotz • Sylvac • Taylor Hobson • Telemeter • Tesa • TesT • Textest • Tira • Trimos • Ultrakust • UTS • Versatile • Vici • Vision Engineering • Vögtlin • Walter • Wayne Kerr • Wegu • Weidmüller • Wenglor • Wenzel • Werth • Dr. Wiesner • Wika • Wilhelm • Wolpert • Yokogawa • Zeiss • ZES Zimmer • Zumbach • Zwick/Roell • Zygo

DIGIMATIC / OPTO

PROXIMITY / POWER

RS232 / 422 / 485

BCD / IEEE

DIGITAL I/O

ANALOG

INDUCTIVE

INCREMENTAL

DC-HI-NET protocol RS232 / USB

Keyboard code (HID)

SPC

Incoming / Outgoing Goods Inspection

Initial Sample Inspection

Machine Capability

Measuring Software

ERP

Office …

Product survey 2019

Rev. 31/2019 of 37

DC-HI-NET interface systems connect all measurement devices and data sources with interfaces like: Interface Measuring technique

DIGIMATIC (MarConnect, MULTIcom, DATA VARIABLE)

▪ Calipers, micrometers, dial gauges, height gauges, protractors ▪ Display units, coating thickness- / force- / roughness-gauges / measuring micro-

scopes …

OPTO PROXIMITY POWER

▪ Calipers, micrometers, dial gauges, height gauges, protractors ▪ Display units …

RS232 RS422 RS485

▪ Balances, display units, colour- / coating thickness- / flow- / gloss- / height- / force- / pressure- / roughness-tester, measuring machines, measuring projectors, multipoint measuring instruments, multimeters

▪ Mobile measuring devices, camera measuring systems, coordinate measuring ma-chines, measuring software, testing machines …

BCD (parallel, serial)

▪ Display units, force gauges, spring testers …

IEEE ▪ Multimeters …

DIGITAL I/O ▪ Controlling of digital inputs/outputs (e.g. relays, end contacts, machine controllers …)

ANALOG ▪ Pressure switches, length measuring instruments, column display units …

INDUCTIVE ▪ Inductive probes (halfbridge / fullbridge)

INCREMENTAL ▪ Incremental transducers with sinusoidal voltage or current interface, TTL, RS422

via one single standardized interface to your software for

▪ Computer Aided Quality assurance (CAQ)

▪ Statistical Process Control (SPC)

▪ Manufacturing Execution Systems (MES)

▪ Production Data Collection (PDC)

▪ Lab data processing

▪ Statistics on PCs.

Product survey 2019

Rev. 31/2019 of 37

The device-independent "DC-HI-NET" protocol provides comfortable functions. Simple commands allow you to pre-process the data. This removes processing load from the host system, and real-time capabilities improve substantially. Features like the automatic measurement device recognition and free configuration protect you from inconvenient administrative and configuration tasks. The "DC-HI-NET" operating system carries out the functions:

▪ Measurement device recognition and transmission protocol adaptation

▪ Communication with the measurement device and parameter assignment

▪ Data format conversion into the unified format

▪ Synchronized data capture and transmission

▪ Data buffering in the system memory

▪ Dynamic data pre-processing like calculation of maximum, minimum and range values

▪ Group operations for multipoint measurement

▪ Self-test and monitoring The function automatic measurement device recognition allows to connect measurement devices with inter-faces like DIGIMATIC or OPTO / PROXIMITY / POWER to one single MULTI interface. The data format is au-tomatically recognized by the interface; additional adjustments are not required.

DC-HI-NET MULTI – the universal interface for:

DIGIMATIC / OPTO … (Standard)

RS232 / 422 / 485 (Option)

IW / bt / RADIO / DIGITAL I/O (Option)

Measurements with interface: ▪ Mitutoyo DIGIMATIC

▪ Sylvac OPTO

▪ Sylvac PROXIMITY

▪ Sylvac POWER

▪ Mahr MarConnect

▪ Atorn multiCOM

▪ Helios-Preisser DATA VARIABLE

▪ Kroeplin DIGIMATIC

Measurement devices like: ▪ Balances, hardness tester,

coating thickness-/force-/height-gauges …

▪ Display units, colour-/form-/ roughness tester, multimeters …

▪ Measuring software for coordi-nate measuring machines, pro-file projectors ...

Configuration for: ▪ IW receiver "MULTI IW"

▪ bt receiver "MULTI bt"

▪ RADIO receiver "MULTI bt"

▪ digital input/output

Product survey 2019

Rev. 31/2019 of 37

NEW! DC-HI-NET IW: Connection of wireless measurement devices

■ Receiver for measurement instruments with integrated wireless interface: ■ Mahr i-wi / Helios Preisser i Series ■ Sylvac BT ■ Tesa TLC-BLE

■ Receiver for a connection with PC and STEINWALD-Interfaces ■ Remote request of values triggered by foot switch (optional) ■ Measurement device ID numbers are saved in the receiver -

WITHOUT any additional software application! ■ Data transfer to CAQ software with STEINWALD protocol

DC-HI-NET bt / RADIO: Wireless measurement data logging

■ Multi-vendor: Transmitter for:

■ DIGIMATIC / MarConnect / OPTO / PROXIMITY / POWER ■ RS232

■ Receiver for a connection with PC and STEINWALD-Interfaces ■ Transmission: Bluetooth® Smart (2,4 GHz) / RADIO (433 MHz) ■ Remote request of values triggered by foot switch (optional) ■ Transmitter ID numbers are saved in the receiver - WITHOUT

any additional software application! ■ Data transfer to CAQ software with STEINWALD protocol

DC-HI-NET SINGLE x-K: Gage connection via the keyboard interface (HID)

■ PC connection via USB keyboard interface (HID) and measure-ment devices with interface: ■ DIGIMATIC / OPTO / PROXIMITY / POWER ■ RS232

■ Wireless measurement device connection (optional) ■ Configurable measurement process and timed data capture ■ Power supply via PC USB interface ■ Data transfer in keyboard code - into each software: Office, CAQ,

MES, ERP... WITHOUT any additional driver!

DC-HI-NET SINGLE x-USB: Measurement device connection via USB interface

■ PC connection via USB (virtual COM port) and measurement de-vices with interface: ■ DIGIMATIC / OPTO / PROXIMITY / POWER ■ RS232/422/485 / BCD / IEEE ■ Incremental / I/O

■ Wireless measurement device connection (optional) ■ Dynamic data preprocessing (MIN/MAX/Range) ■ Multipoint measurement ■ Power supply via PC USB interface ■ Data transfer to CAQ software with STEINWALD protocol

Product survey 2019

Rev. 31/2019 of 37

DC-HI-NET SINGLE x-RS: Measurement device connection via RS232 interface

■ PC connection via RS232 interface and measurement devices with interface: ■ DIGIMATIC / OPTO / PROXIMITY / POWER ■ RS232/422/485 ■ Inductive / Analog

■ Wireless measurement device connection (optional) ■ Dynamic data pre-processing (MIN/MAX/Range) ■ Multipoint measurement ■ Integrated power supply ■ Data transfer to CAQ software with STEINWALD protocol

Software and accessories

The MS-Windows test program "DCDemo32" checks all "DC-HI-NET" functions. Actual data, syn-chronization impulses and error messages, sorted by channel, are displayed on the monitor in real time. The test program is an ef-fective support tool for setup and test of measurement sets and during troubleshooting. The well-documented, easy-to-

use driver library (DLL for Mi-crosoft Windows®), delivered with a comprehensive user manual and software samples, allows data capture into your Windows® applications without huge pro-gramming effort. It supports event-driven data cap-ture and formula calculations with channel coupling.

E.g., multipoint measurements can be carried out very simply, and the results are transferred directly into Microsoft Excel®. Accessories like control elements for data capture, cable for several computer and measurement de-vice types, protection shelves and special connectors simplify your daily work.

Services

We implement fast and cost-efficient drivers for special measurement equipment into our system software. Thanks to the standardized "DC-HI-NET" protocol, you are able to control all your measurement devices using one unique host software. For tests we offer leasing devices. You can test your host software together with the measurement equipment under real conditions during the quote phase.

For your projects we support you with installation and setup of the whole solution. We have ex-perience equipping production lines with measurement and con-trol systems, CAQ and SPC. As a supplier-independent provider of components for measurement technology and quality assurance, we possess a wide range of know-how which often helps more than highly specialized knowledge of a single product.

For technical support we operate a hotline. Normally, we support our customers free of charge, but we also offer support contracts to guarantee certain reaction times and service levels. We are continuing to enhance the "DC-HI-NET" system compatibly. Devices already in operation can be equipped with new functions via updates to the operating sys-tem.

Product survey 2019

Rev. 31/2019 of 37

3. Order information DC-HI-NET "IW" With DC-HI-NET "IW" we offer a solution for connection of measurement instruments with integrated wire-less interface. The "IW" receivers are available for Mahr i-wi, Helios Preisser i Series, Sylvac BT and Tesa TLC-BLE. Activation of measurement value transfer occurs via transfer button on the measurement instrument or the STEINWALD foot switch/hand switch (optional) Measurement device ID numbers are saved in the "IW" receiver - WITHOUT any additional software applica-tion! The "IW" receivers are available in two variants: SINGLE IWx-USB for direct connection via the PC USB inter-face in "DC-HI-NET" protocol and the plug-in solution MULTI IWx for a connection to the "MULTI" input of a "DC-HI-NET" interface device.

The following components are required for data collection with DC-HI-NET "IW":

1. DC-HI-NET "IW" Receiver For connection to a PC-USB interface: SINGLE IW1-USB / SINGLE IW2-USB For connection to a DC-HI-NET "MULTI" input: MULTI IW1 / MULTI IW2

Delivery includes one manual.

Product survey 2019

Rev. 31/2019 of 37

4. Product survey DC-HI-NET "IW" The usage outside of the EU and EFTA is not permitted!

NEW: SINGLE IW1-USB IW receiver 20-27-0431 Connection: 8 x Sylvac "BT" / Tesa "TLC-BLE"-

measurement instruments Transmission: Bluetooth® Data transfer: Transfer button on instrument Size: 12 x 21 x 77 mm (H x W x D)

Interface device for connection of measuring instruments with integrated wireless interface Sylvac "BT" or Tesa "TLC-BLE". PC connection and power supply via USB interface.

NEW: SINGLE IW2-USB IW receiver 20-27-0432 Connection: 8 x Mahr "i-wi" / Helios-Preisser "i"-

measurement instruments Transmission: Ant+® Data transfer: Transfer button on instrument Size: 12 x 21 x 77 mm (H x W x D)

Interface device for connection of measuring instruments with integrated wireless interface Mahr "i-wi" or Helios-Preisser "i". PC connection and power supply via USB interface.

NEW: MULTI IW1 IW receiver 20-29-0431 Connection: 8 x Sylvac "BT" / Tesa "TLC-BLE"-

measurement instruments Transmission: Bluetooth® Data transfer: Transfer button on instrument or STEINWALD foot-/hand switch Size: 9 x 20 x 65 mm (H x W x D)

Receiver for for connection of measuring instruments with integrated wireless interface Sylvac "BT" or Tesa "TLC-BLE". Connection with DC-HI-NET interface devices with MULTI input

NEW: MULTI IW2 IW receiver 20-29-0432 Connection: 8 x Mahr "i-wi"- / Helios-Preisser "i"-

measurement instruments Transmission: Ant+® Data transfer: Transfer button on instrument or STEINWALD foot-/hand switch Size: 9 x 20 x 65 mm (H x W x D)

Receiver for for connection of measuring instruments with integrated wireless interface Mahr "i-wi" or Helios-Preisser "i". Connection with DC-HI-NET interface devices with MULTI input

MULTI IW special driver Firmware for DC-HI-NET 20-30-9990 Firmware for the connection of a MULTI IWx receiver with a

DC-HI-NET MULTI input

IW special driver Firmware for DC-HI-NET 20-30-9991 Firmware for MULTI IWx / SINGLE IWx-USB

extension for remote request of values triggered by the STEINWALD foot/hand switch

Product survey 2019

Rev. 31/2019 of 37

5. Order information DC-HI-NET "bt" With DC-HI-NET "bt" we offer a solution for wireless measurement data logging via Bluetooth®. The "bt" transmitters are easy to install on measurement instruments and are available for DIGIMATIC- / OPTO- / PROXIMITY- / PROXIMITY- and RS232 data export. Activation of measurement value transfer occurs via transfer button on the transmitter or measurement device. Three color LEDs make visualization of the trans-fer and tolerance status possible (must be supported by SPC software). Clear assignment of the transmitter to a "DC-HI-NET" measurement channel occurs via the transmitter's ID number. The "bt" receivers are available in two variants: SINGLE bt-USB for direct connection via the PC-USB inter-face in "DC-HI-NET" protocol and the plug-in solution MULTI bt for a connection to the "MULTI" input of a "DC-HI-NET" interface device.

The following components are required for data collection with DC-HI-NET "bt":

1. One DC-HI-NET "bt" Receiver For connection to a PC USB interface: SINGLE bt-USB For connection to a DC-HI-NET "MULTI" input: MULTI bt

2. DC-HI-NET "bt" Transmitter Suitable measurement device type for installation on device With 3 V lithium batteries, plastic housing (52 x 26 x 16 mm3)

Delivery includes one manual.

Product survey 2019

Rev. 31/2019 of 37

6. Product survey DC-HI-NET "bt" The usage outside of the EU and EFTA is not permitted!

SINGLE bt-USB bt receiver 20-27-0410 Connection: 8 x DC-HI-NET "bt" transmitter Transmission: 2,4 GHz (Bluetooth®) Data transfer: Transfer button on "bt" transmitter Size: 12 x 21 x 77 mm (H x W x D)

Interface device for wireless connection of measuring instru-ments with DIGIMATIC and OPTO / PROXIMITY / POWER interface type via DC-HI-NET "bt" transmitter. PC connection and power supply via USB interface.

SINGLE bt-USB bt receiver with connector for foot/hand switch 20-27-0411 Connection: 8 x DC-HI-NET "bt" transmitter Transmission: 2,4 GHz (Bluetooth®) Data transfer: Transfer button on "bt" transmitter Data capture: Connector for foot / hand switch Size: 12 x 21 x 77 mm (H x W x D)


SINGLE bt-K bt receiver with PC keyboard interface (HID) 20-26-0410 Connection: 8 x DC-HI-NET "bt" transmitter Transmission: 2,4 GHz (Bluetooth®) Data transfer: Transfer button on "bt" transmitter Size: 12 x 21 x 77 mm (H x W x D)


MULTI bt bt receiver 20-29-0510 Connection: max. 8 x DC-HI-NET "bt" transmitter Transmission: 2,4 GHz (Bluetooth®) Data transfer: Transfer button on "bt" transmitter Size: 9 x 20 x 65 mm (H x W x D)

Receiver for wireless measurement instruments connection with DIGIMATIC type interfaces and OPTO / PROXIMITY / POWER via DC-HI-NET "bt" transmitter. Connection with DC-HI-NET interface devices with MULTI input.

MULTI bt special driver Firmware for DC-HI-NET 20-30-9987 Firmware for the connection of a MULTI bt receiver with a DC-

HI-NET MULTI input.

bt special driver Firmware for DC-HI-NET 20-30-9988 Firmware for MULTI bt / SINGLE bt-USB

extension for remote request of values triggered by the STEINWALD foot/hand switch

bt transmitter 1 x Mitutoyo DIGIMATIC (5 pin/flat) 20-29-0601 Connection: 1 x Mitutoyo DIGIMATIC measure-

ment instrument Transmission: 2,4 GHz (Bluetooth® ) Data transfer: Transfer button on transmitter

bt transmitter including connection adapter for measurement instruments with Mitutoyo DIGIMATIC interfaces (5-pin./flat - connection adapter angled to the right, left or rear available). Maximum range: 10 m

bt transmitter 1 x Mitutoyo DIGIMATIC (5-pin./Data button) 20-29-0607 Connection: 1 x Mitutoyo DIGIMATIC measure-

ment instrument Transmission: 2,4 GHz (Bluetooth®) Data transfer: Transfer button on transmitter

bt transmitter including connection adapter for measurement instruments with Mitutoyo DIGIMATIC (5-pin./Data button) interfaces. Maximum range: 10 m.

bt transmitter 1 x Mitutoyo DIGIMATIC (6-pin./round) 20-29-0608 Connection: 1 x Mitutoyo DIGIMATIC measure-


bt transmitter including connection adapter for measurement instruments with Mitutoyo DIGIMATIC (6-pin./round) interfaces. Maximum range: 10 m.

bt transmitter 1 x Mitutoyo DIGIMATIC (10-pin.) 20-29-0602 Connection: 1 x Mitutoyo DIGIMATIC measure-


bt transmitter including connection adapter for measurement instruments with Mitutoyo DIGIMATIC (10-pin.) interfaces. Maximum range: 10 m.

Product survey 2019

Rev. 31/2019 of 37

bt transmitter 1 x Mitutoyo DIGIMATIC calipers IP6x 20-29-0615 Connection: 1 x Mitutoyo DIGIMATIC measure-


bt transmitter including connection adapter for Mitutoyo DIGI-MATIC calipers IP6x. Maximum range: 10 m.

bt transmitter 1 x Mitutoyo DIGIMATIC micrometer IP6x 20-29-0616 Connection: 1 x Mitutoyo DIGIMATIC measure-


bt transmitter including connection adapter for Mitutoyo DIGI-MATIC micrometer IP6x. Maximum range: 10 m.

bt transmitter 1 x Mahr MarConnect 20-29-0609 Connection: 1 x Mahr MarConnect interface Transmission: 2,4 GHz (Bluetooth®) Data transfer: Transfer button on transmitter

bt transmitter including connection adapter for Mahr measure-ment instruments with interface MarConnect (Atorn multiCOM / Helios-Preisser DATA VARIABLE). Maximum range: 10 m.

bt transmitter 1 x Sylvac OPTO 20-29-0600 Connection: 1 x Sylvac OPTO measuring device Transmission: 2,4 GHz (Bluetooth®) Data transfer: Transfer button on transmitter

bt transmitter including connection adapter for measurement instruments with Sylvac OPTO interfaces (direct output) and compatible models (e.g. Atorn, Diatest, Käfer, Kordt, Mahr / Helios, Preisser, Sylvac, Tesa). Maximum range: 10 m.

bt transmitter 1 x Sylvac PROXIMITY 20-29-0629 Connection: 1 x Sylvac PROXIMITY measuring

device Transmission: 2,4 GHz (Bluetooth®) Data transfer: Transfer button on transmitter

bt transmitter including connection adapter for measurement instruments with Sylvac PROXIMITY interfaces. Maximum range: 10 m.

bt transmitter 1 x Sylvac POWER 20-29-0619 Connection: 1 x Sylvac POWER measuring

device Transmission: 2,4 GHz (Bluetooth®) Data transfer: Transfer button on transmitter

bt transmitter including connection adapter for measurement instruments with Sylvac POWER interfaces. Maximum range: 10 m.

bt transmitter 1 x Kroeplin-Digimatic 20-29-0603 Connection: 1 x Kroeplin-Digimatic Transmission: 2,4 GHz (Bluetooth® ) Data transfer: Transfer button on transmitter

bt transmitter including connection adapter for Kropelin inter-nal/external measurement instrument with Digimatic interface. Maximum range: 10 m.

bt transmitter 1 x Kroeplin-Digimatic 20-29-0626 Connection: 1 x Kroeplin-Digimatic Transmission: 2,4 GHz (Bluetooth®) Data transfer: Transfer button on transmitter

bt transmitter including connection adapter for Kropelin inter-nal/external measurement instrument C-/G series via Kroeplin interface Mitutoyo Digimatic no 1961-09 Maximum range: 10 m.

bt transmitter 1 x RS232 (customer specific) 20-29-0699 Connection: 1 x RS232 Transmission: 2,4 GHz (Bluetooth®) Data transfer: Transfer button on transmitter

bt transmitter including connection adapter for instruments with RS232 interface (e. g. Bareiss HPE II / Chatillon DFE II / CHECKLINE TI-007 / Karl Deutsch ECHOMETER 1076 / Keyence DL-RS1A / KRAUTKRAMER CL5 / Mahr DIGIMAR 816 CL; 817 CLM; CX1/2; MarSurf PS 10 / Mecmesin AFG Mk IV / Sartorius Combics IP-44 / Sylvac Hi_Cal 150/300/450 / Tesa HITE 400/700; MICRO-HITE 350/600/900; MICRO-HITE PLUS M 350/600/900), Measurement device connection only via special drivers in DC-HI-NET interface. Maximum range: 10 m

Product survey 2019

Rev. 31/2019 of 37

7. Order information DC-HI-NET "RADIO" With DC-HI-NET "RADIO" we offer a solution for wireless measurement data logging via radio. The RADIO transmitters are easy to install on measurement instruments and are available for DIGIMATIC-, OPTO- / PROXIMITY- / PROXIMITY- and "RS232" data export. Activation of measurement value transfer oc-curs via transfer button on the transmitter or measurement device. Three color LEDs make visualization of the transfer and tolerance status possible (must be supported by SPC software). Clear assignment of the transmit-ter to a "DC-HI-NET" measurement channel occurs via the transmitter's ID number. The RADIO receivers are available in two variants: SINGLE W for direct connection via the PC USB interface in "DC-HI-NET" protocol and the plug-in solution MULTI W for a connection to the MULTI input of a "DC-HI-NET" interface device. Transmitter and receiver are available for the frequency 433 MHz with 64 radio channels (configurable), so that complications with other radio applications can be avoided.

The following components are required for data collection with DC-HI-NET "RADIO":

1. One RADIO Receiver For connection to a PC USB interface: SINGLE W (incl. USB connection cable) For connection to a DC-HI-NET "MULTI" input: MULTI W

2. RADIO Transmitter Suitable measurement device type for installation on device With 3 V lithium batteries, plastic housing (52 x 26 x 16 mm3)

Delivery includes one USB connection cable for SINGLE W and one manual.

Product survey 2019

Rev. 31/2019 of 37

8. Product survey DC-HI-NET "RADIO" The usage outside of the EU and EFTA is not permitted!

SINGLE W Radio receiver 20-27-0400 Connection: 78 x DC-HI-NET "RADIO" transmitter Transmission: 433 MHz (64 channels) Data transfer: Transfer button on FUNK transmitter Size: 26 x 55 x 161 mm (H x W x D)

Interface device for wireless connection of measuring instru-ments with DIGIMATIC and OPTO / PROXIMITY / POWER interface type via DC-HI-NET "RADIO" transmitter. PC connection and power supply via USB interface. Incl. USB connection cable

MULTI W Radio receiver 20-29-0010 Connection: max. 78 x DC-HI-NET "RADIO"

transmitter Transmission: 433 MHz (64 channels) Data transfer: Transfer button on Radio transmitter Size: 9 x 20 x 65 mm (H x W x D)

Receiver for wireless measurement instruments connection with Mitutoyo DIGIMATIC type interfaces and OPTO / PROX-IMITY / POWER via DC-HI-NET "RADIO" transmitter. Connection with DC-HI-NET interface devices with MULTI input

MULTI W special driver Firmware for DC-HI-NET 20-30-9985 Firmware for the connection of a MULTI W RADIO receiver

with a DC-HI-NET MULTI input

RADIO transmitter 1 x Mitutoyo DIGIMATIC (5 pin/flat) 20-29-0101 Connection: 1 x Mitutoyo DIGIMATIC measure-

ment instrument Transmission: 433 MHz (64 channels) Data transfer: Transfer button on transmitter

Radio transmitter including connection adapter for measure-ment instruments with Mitutoyo DIGIMATIC (5-pin./flat) inter-faces. (connection adapter angled to the right, left or rear available). Maximum range: 5 m / 20 m

RADIO transmitter 1 x Mitutoyo DIGIMATIC (5-pin./Data button) 20-29-0107 Connection: 1 x Mitutoyo DIGIMATIC measure-


Radio transmitter including connection adapter for measure-ment instruments with Mitutoyo DIGIMATIC (5-pin./Data button) interfaces. Maximum range: 5 m / 20 m.

RADIO transmitter 1 x Mitutoyo DIGIMATIC (6-pin./round) 20-29-0108 Connection: 1 x Mitutoyo DIGIMATIC measure-


Radio transmitter including connection adapter for measure-ment instruments with Mitutoyo DIGIMATIC (6-pin./round) interfaces. Maximum range: 5 m / 20 m.

RADIO transmitter 1 x Mitutoyo DIGIMATIC (10-pin.) 20-29-0102 Connection: 1 x Mitutoyo DIGIMATIC measure-


Radio transmitter including connection adapter for measure-ment instruments with Mitutoyo DIGIMATIC (10-pin.) interfac-es. Maximum range: 5 m / 20 m.

RADIO transmitter 1 x Mitutoyo DIGIMATIC calipers IP6x 20-29-0115 Connection: 1 x Mitutoyo DIGIMATIC measure-


Radio transmitter including connection adapter for Mitutoyo calipers IP6x. Maximum range: 5 m / 20 m.

RADIO transmitter 1 x Mitutoyo DIGIMATIC micrometer IP6x 20-29-0116 Connection: 1 x Mitutoyo DIGIMATIC measure-


Radio transmitter including connection adapter for Mitutoyo micrometer IP6x. Maximum range: 5 m / 20 m.

Product survey 2019

Rev. 31/2019 of 37

RADIO transmitter 1 x Mahr MarConnect 20-29-0109 Connection: 1 x Mahr MarConnect interface Transmission: 433 MHz (64 channels) Data transfer: Transfer button on transmitter

Radio transmitter including connection adapter for Mahr meas-urement instruments with interface MarConnect (multiCOM / DATA VARIABLE). Maximum range: 5 m / 20 m.

RADIO transmitter 1 x Sylvac OPTO 20-29-0100 Connection: 1 x Sylvac OPTO measuring device Transmission: 433 MHz (64 channels) Data transfer: Transfer button on transmitter

Radio transmitter including connection adapter for measure-ment instruments with Sylvac OPTO interfaces (direct output) and compatible models (e.g. Atorn, Diatest, Käfer, Kordt, Mahr / Helios, Preisser, Sylvac, Tesa). Maximum range: 5 m / 20 m.

RADIO transmitter 1 x Sylvac PROXIMITY 20-29-0129 Connection: 1 x Sylvac PROXIMITY measuring

device Transmission: 433 MHz (64 channels) Data transfer: Transfer button on transmitter

Radio transmitter including connection adapter for measure-ment instruments with Sylvac PROXIMITY interfaces. Maximum range: 5 m / 20 m.

RADIO transmitter 1 x Sylvac POWER 20-29-0119 Connection: 1 x Sylvac POWER measuring

device Transmission: 433 MHz (64 channels) Data transfer: Transfer button on transmitter

Radio transmitter including connection adapter for measure-ment instruments with Sylvac POWER interfaces. Maximum range: 5 m / 20 m.

RADIO transmitter 1 x Kroeplin-Digimatic 20-29-0103 Connection: 1 x Kroeplin-Digimatic Transmission: 433 MHz (64 channels) Data transfer: Transfer button on transmitter

Radio transmitter including connection adapter for Kropelin internal/external measurement instrument with Digimatic interface. Maximum range: 5 m / 20 m

RADIO transmitter 1 x Kroeplin-Digimatic 20-29-0626 Connection: 1 x Kroeplin-Digimatic Transmission: 433 MHz (64 channels) Data transfer: Transfer button on transmitter

Radio transmitter including connection adapter for Kropelin internal/external measurement instrument C-/G series via Kroeplin interface Mitutoyo Digimatic no 1961-09 Maximum range: 5 m / 20 m.

RADIO transmitter 1 x RS232 (customer specific) 20-29-0199 Connection: 1 x RS232 Transmission: 433 MHz (64 channels) Data transfer: Transfer button on transmitter

Radio transmitter including connection adapter for devices with RS232 interface, measurement instrument connection only via special drivers in DC-HI-NET interface. Maximum range: 5 m / 20 m

Product survey 2019

Rev. 31/2019 of 37

9. Order information DC-HI-NET "SINGLE x-K" DC-HI-NET "SINGLE x-K" transmits the data from the digital manual measuring tools to a PC USB keyboard interface (HID). The measured values are available to any PC application without the need for time-consuming driver installation. The channel required for the data transfer is activated using a channel selection switch. The capture of measured values is triggered via a foot switch or with the transfer button on the measuring tool. The measured value is transferred into the current cursor field of the PC program. The power is supplied via the PC. "SINGLE x-K" devices are delivered in a robust metal housing. Data capture via DC-HI-NET "SINGLE x-K" requires:

1. One DC-HI-NET "SINGLE x-K" Basic device (incl. USB connection cable) With 1, 3 or 6 inputs for digital manual measurement devices in any combination With automatic measurement device recognition

SINGLE M1-K 1 MULTI input for digital manual

measurement devices with inter-face DIGIMATIC / OPTO / PROXIMITY / POWER Opt.: RS232 / IW / bt / RADIO

SINGLE M3-K 3 MULTI inputs for digital manual

measurement devices with inter-face DIGIMATIC / OPTO / PROXIMITY / POWER Opt.: RS232 / IW / bt / RADIO

Delivery includes one USB connection cable and one manual.

2. Options Control elements for data capture (hand or foot switch) Measurement device connection cables

Transfer button

Channel display

Channel selection button

Data inputs

Product survey 2019

Rev. 31/2019 of 37

10. Product survey DC-HI-NET "SINGLE x-K" SINGLE M1-K 1 x digital manual measuring tools / RS232 20-26-0320 Connection: 1 x DIGIMATIC, OPTO / PROXIMITY

/ POWER Cable: from measurement device manufac-

turer or from STEINWALD Data capture: Connector for foot / hand switch,

transfer button at the interface Size: 28 x 55 x 62 mm (H x W x D)

Interface device with PC USB keyboard interface (HID) for 1 measurement device with interfaces like DIGIMATIC or Sylvac OPTO / PROXIMITY / POWER. On request: Driver for connection of measurement device with RS232 interface Incl. USB connection cable

SINGLE M3-K 3 x digital manual measuring tools / RS232 20-26-0311 Connection: 3 x DIGIMATIC, OPTO / PROXIMITY


turer or from STEINWALD Data capture: Connector for foot / hand switch Size: 42 x 121 x 143 mm (H x W x D)

Interface device with PC USB keyboard interface (HID) for any combination of 3 measurement devices with interfaces like DIGIMATIC or Sylvac OPTO / PROXIMITY / POWER. On request: Driver for connection of measurement devices with RS232 interface Incl. USB connection cable

SINGLE M6-K 6 x digital manual measuring tools / RS232 20-26-0312 Connection: 6 x “DIGIMATIC”, OPTO / PROXIMI-

TY / POWER Cable: from measurement device manufac-


Interface device with PC USB keyboard interface (HID) for any combination of 6 measurement devices with interfaces like DIGIMATIC or Sylvac OPTO / PROXIMITY / POWER. On request: Driver for connection of measurement devices with RS232 interface Incl. USB connection cable

Product survey 2019

Rev. 31/2019 of 37

11. Order information DC-HI-NET "SINGLE x-USB" DC-HI-NET "SINGLE x-USB" is interface-compatible with DC-HI-NET "SINGLE x-RS". The PC connection and the power supply are made via the USB interface. "SINGLE x-USB" devices are delivered in a robust metal housing. For data capture with DC-HI-NET "SINGLE x-USB" are necessary:

1. One DC-HI-NET "SINGLE x-USB" Basic device (incl. USB connection cable) For digital manual measurement devices in any combination For measurement devices with RS232/BCD/IEEE interface (on request via special driver configura-

tion) For optical-incremental transducers

SINGLE M2-USB 2 MULTI inputs for digital manual

measurement devices with interface DIGIMATIC / OPTO / PROXIMITY / POWER

Opt.: RS232 / IW / bt / RADIO / I/O

SINGLE M8-USB 8 MULTI inputs for digital manual

measurement devices with interface DIGIMATIC / OPTO / PROXIMITY / POWER

Opt.: RS232 / IW / bt / RADIO / I/O

Option: Firmware "cascading" to upgrade up to 78 measurement device inputs.

Delivery includes one USB connection cable and one manual. Download USB-/COM device driver for Microsoft Windows® 2000 / XP / Vista / 7 / 8 / 10: http://usb.steinwald.com

2. Options Control elements for data capture (hand or foot switch) Measurement device connection cables Software tools (driver, DLL or data capture software)

MULTI inputs for digital measurement devices

Product survey 2019

Rev. 31/2019 of 37

12. Product survey DC-HI-NET "SINGLE x-USB"

SINGLE M1-USB 1 x digital manual measuring tools / RS232 20-27-0321 Connection: 1 x DIGIMATIC, OPTO / PROXIMITY

/ POWER Cable: from STEINWALD Data capture: Connector for foot / hand switch Size: 26 x 55 x 112 mm (H x W x D)

Interface device with one MULTI input for measurement devic-es with Mitutoyo DIGIMATIC type interfaces and Sylvac OPTO / PROXIMITY / POWER. On request: Driver for connection of measurement devices with RS232 interface. Select the corresponding driver and compatible devices from the "List of measurement devices" (see app.). Incl. USB connection cable




Interface device with two MULTI inputs for the freely combi-nable connection of measurement devices with Mitutoyo DIGIMATIC type interfaces and Sylvac OPTO / PROXIMITY / POWER. On request: Driver for connection of measurement devices with RS232 interface. Select the corresponding driver and compatible devices from the "List of measurement devices" (see app.). Incl. USB connection cable




Interface device with four MULTI inputs for the freely combi-nable connection of measurement devices with Mitutoyo DIGIMATIC type interfaces and Sylvac OPTO / PROXIMITY / POWER. On request: Driver for connection of measurement devices with RS232 interface. Select the corresponding driver and compatible devices from the "List of measurement devices" (see app.). Incl. USB connection cable




Interface device with eight MULTI inputs for the freely combi-nable connection of measurement devices with Mitutoyo DIGIMATIC type interfaces and Sylvac OPTO / PROXIMITY / POWER. On request: Driver for connection of measurement devices with RS232 interface. Select the corresponding driver and compatible devices from the "List of measurement devices" (see app.). Incl. USB connection cable

SINGLE BCD1-USB 1 x data format BCD / IEEE 20-27-0500 Connection: 1 x BCD / IEEE Cable: select from "List of measurement

devices" Data capture: Connector for foot / hand switch Size: 40 x 121 x 183 mm (H x W x D)

Interface device with one BCD / IEEE interface upon request. Select the corresponding driver and compatible devices from the "List of measurement devices" (see app.) Incl. USB connection cable

SINGLE I/O-USB 12 digital inputs and outputs 20-27-0550 Anschluss: 12 x digital potential-free input

/output (up to 24V) Kabel: special version (on request) Size: 40 x 121 x 183 mm (H x W x D)

Interface device with 12 potential-free digital inputs and outputs for control tasks like relays, end contacts, machine controllers (configuration according demand). Incl. USB connection cable

SINGLE INCM2-USB 1 x incremental transducer 1 Vpp

1 x digital manual measuring tool / RS232 20-27-0720

Connection: 1 x Connection for incremental transducer 1 Vpp 1 x DIGIMATIC, OPTO / PROXIMITY / POWER

Cable: at the probe (15-pin D-Sub connect-or)

from measurement device manufac-turer or from STEINWALD

Data capture: Connector for foot / hand switch Siize: 40 x 121 x 183 mm (H x W x D)

Interface device with one incremental transducer with sinusoidal voltage interface 1 Vpp, sensor error detection (gauge defective / measuring speed to fast), Interpolation rate programmable up to 200 x, input frequency max. 333 KHz as well as one MULTI input for connection of measurement devices with Mitutoyo DIGIMATIC type interfaces and Sylvac OPTO / PROXIMITY / POWER Optional: zero balancing switch Incl. USB connection cable

Product survey 2019

Rev. 31/2019 of 37

SINGLE INC2-USB 2 x incremental transducer 1 Vpp 20-27-0701 Connection: 2 x Connection for incremental

transducers 1 Vpp Cable: at the probe (15-pin D-Sub connect-

or) Data capture: Connector for foot / hand switch Siize: 40 x 121 x 183 mm (H x W x D)

Interface device for two incremental transducers with sinusoidal voltage interface 1 Vpp, Sensor error detection (gauge defective / measuring speed to fast), Interpolation rate programmable up to 200 x, input frequency max. 333 KHz, Optional: zero balancing switch Incl. USB connection cable

SINGLE INC2-USB 2 x incremental transducer 11 µApp 20-27-0711 Connection: 2 x Connection for incremental

transducers 11 µApp Cable: at the probe (15-pin D-Sub connect-

or) Data capture: Connector for foot / hand switch Size: 40 x 121 x 183 mm (H x W x D)

Interface device for two incremental transducers with sinusoidal current interface 11 µApp, Sensor error detection (gauge defective / measuring speed to fast), Interpolation rate programmable up to 200 x, input frequency max. 333 KHz, Optional: zero balancing switch Incl. USB connection cable

SINGLE INC4-USB 4 x incremental transducer 1 Vpp 20-27-0703 Connection: 4 x Connection for incremental

transducers 1 Vpp Cable: at the probe (15-pin D-Sub connect-

or) Data capture: Connector for foot / hand switch Siize: 62 x 121 x 183 mm (H x W x D)

Interface device for four incremental transducers with sinusoidal voltage interface 1 Vpp, Sensor error detection (gauge defective / measuring speed to fast), Interpolation rate programmable up to 200 x, input frequency max. 333 KHz, Optional: zero balancing switch Incl. USB connection cable

SINGLE INC4-USB 4 x incremental transducer 11 µApp 20-27-0713 Connection: 4 x Connection for incremental

transducers 11 µApp Cable: at the probe (15-pin D-Sub connect-


Interface device for four incremental transducers with sinusoidal current interface 11 µApp, Sensor error detection (gauge defective / measuring speed to fast), Interpolation rate programmable up to 200x, input frequency max. 333 KHz, Optional: zero balancing switch Incl. USB connection cable

SINGLE INC2-USB 2 x incremental transducer TTL / RS422 20-27-0731 Connection: 2 x Connection for incremental

transducers TTL / RS422 Cable: at the probe (15-pin D-Sub connect-


Interface device for two incremental transducers with square-wave TTL / RS422 interface, Optional: zero balancing switch Incl. USB connection cable

SINGLE x-USB<->SINGLE x-USB Cable between 2 DC-HI-NET "SINGLE x-USB" 20-28-2811 Connection: 1 x Connection between 2 DC-HI-

NET SINGLE x-USB via RS485 Size: Length: 2m

Connection cable for serial coupling of two DC-HI-NET "SINGLE x-USB" via RS485. (Not for SINGLE M1-USB / M2-USB!)

Product survey 2019

Rev. 31/2019 of 37

13. Order information DC-HI-NET "SINGLE x-RS" The DC-HI-NET "SINGLE x-RS" device family is interface-compatible with DC-HI-NET "SINGLE x-RS ". Via the additional "cascading" firmware the option exists to upgrade to up to 78 measurement device inputs.

Cascading from up to 2 devices via RS232 (Cable 20-28-2829)

Cascading for up to 78 channels via RS485 (Cable 20-28-2818 + 20-28-2819)

The devices are delivered in robust metal housing with the following dimensions: The following components are required for a fixed configuration DC-HI-NET "SINGLE x-RS" interface device:

1. One DC-HI-NET "SINGLE x-RS" Basic device For digital manual measurement devices in any combination For measurement devices with RS232 interface (on request via special driver configuration) For inductive probes

SINGLE INDM8-RS

4 inputs for inductive probes 4 MULTI inputs for digital manual

measurement devices with interface DIGIMATIC / OPTO / PROXIMITY / POWER Opt.: RS232 / IW / bt / RADIO / I/O

Delivery includes power supply cable and one manual.

2. Serial connection cable For the data transfer between DC-HI-NET and host computer Available for various host computer types (PC, workstation, terminal)

3. Options Control elements for data capture (hand or foot switch) Measurement device connection cables Software tools (driver, DLL or data capture software)

"MULTI" inputs Inputs for inductive probes

Product survey 2019

Rev. 31/2019 of 37

14. Product survey DC-HI-NET "SINGLE x-RS" SINGLE M4-RS 4 x digital manual measuring tools / RS232 20-24-0310 Connection: 4 x DIGIMATIC, OPTO / PROXIMITY



Interface device with four MULTI inputs for the freely combina-ble connection of measurement devices with Mitutoyo DIGI-MATIC type interfaces and Sylvac OPTO / PROXIMITY / POWER. On request: Driver for connection of measurement devices with RS232 interface. Select the corresponding driver and compatible devices from the "List of measurement devices" (see app.).

SINGLE M8-RS 8 x digital manual measuring tools / RS232 20-24-0311 Connection: 8 x DIGIMATIC, OPTO / PROXIMITY



Interface device with eight MULTI inputs for the freely combin-able connection of measurement devices with Mitutoyo DIGI-MATIC type interfaces and Sylvac OPTO / PROXIMITY / POWER. On request: Driver for connection of measurement devices with RS232 interface. Select the corresponding driver and compatible devices from the "List of measurement devices" (see app.).

SINGLE INDM8-RS 4 x inductive half-bridge probes

4 x digital manual measuring tools / RS232 20-24-0330

Connection: 4 x Inductive half-bridge probes with Tesa balancing

4 x DIGIMATIC, OPTO / PROXIMITY / POWER,

Cable: at the probe from measurement device manufac-


Interface device with four inductive half-bridge probes with Tesa balancing and compatibles (On request: LVDT probes). Resolution: 0,5 µm, precision: ±2 µm at measuring range ±1 mm (depending on probe type) as well as four "MULTI" inputs for the freely combinable connection of measurement devices with Mitutoyo DIGIMATIC type interfaces and Sylvac OPTO / PROXIMITY / POWER On request: Driver for connection of measurement devi-ces with RS232 interface. Select the corresponding driver and compatible devices from the "List of measurement devices" (see app.).

SINGLE IND4-RS 4 inductive probes 20-24-0815 Connection: 4 x Inductive half-bridge probes with

Tesa balancing Cable: at the probe Data capture: Connector for foot / hand switch Size: 62 x 121 x 247 mm (H x W x D)

Interface device for 4 inductive half-bridge probes with Tesa balancing and compatibles (On request: LVDT probes). Resolution: 0,5 µm, precision: ±3 µm at measuring range ±1 mm (depending on probe type)

SINGLE IND8-RS 8 inductive probes 20-24-0816 Connection: 8 x Inductive half-bridge probes with

Tesa balancing Cable: at the probe Data capture: Connector for foot / hand switch Size: 91 x 121 x 247 mm (H x W x D)

Interface device for 8 inductive half-bridge probes with Tesa balancing and compatibles (On request: LVDT probes). Resolution: 0,5 µm, precision: ±3 µm at measuring range ±1 mm (depending on probe type)

Product survey 2019

Rev. 31/2019 of 37

15. Order information DC-HI-NET "SINGLE IPx-RS" For applications under "rough" industrial conditions we offer a version of DC-HI-NET "SINGLE" with protection level IP65. The device has 8 inputs for digital manual measurement gages (splash proof connectors) and can optionally be equipped with RS232 inputs. DC-HI-NET "SINGLE IPx-RS" is connection and interface compatible with DC-HI-NET "SINGLE", only a special PC connection cable is required. "SINGLE IPx-RS" are delivered in a robust metal housing. For data capture with DC-HI-NET "SINGLE IPx-RS" are necessary:

1. A complete device DC-HI-NET "SINGLE IPx-RS" with 8 interfaces for digital manual measurement gages ready to use with serial interface to the host computer

DC-HI-NET SINGLE IP8-RS

8 interfaces for digital manual measurement devices with inter-face DIGIMATIC / OPTO / PROXIMITY / POWER Opt.: RS232

Delivery contains a comprehensive manual.

2. A serial PC connection cable for data transmission "DC-HI-NET" – Host computer with protected plug (splash proof)

3. Options Control elements for data capture (hand or foot switch with protection level IP65) Measurement device connection cables (with special protected plugs) Software tools (driver, DLL or data capture software)

Measurement inputs Protected covers

Product survey 2019

Rev. 31/2019 of 37

16. Product survey DC-HI-NET "SINGLE IPx-RS" SINGLE IP8-RS 8 x digital manual measuring tools 20-24-0315 Connection: 8 x DIGIMATIC, OPTO / PROXIMITY

/ POWER Cable: from STEINWALD Data capture: Connector for foot / hand switch Size: 91 x 121 x 285 mm (H x W x D)

Interface device in protection class IP65 for any combination of 8 measurement devices with interfaces like Mitutoyo DIGI-MATIC and Sylvac OPTO / PROXIMITY / POWER. On request: Driver for connection of measurement devices with RS232 interface.

PC (9-pin)/SINGLE IPx-RS Cable to PC 20-28-2825 Connection: 1 x Connection to the PC via serial

interface Size: Length: 2 m

Host connection cable for the serial PC connection via RS232 (splash-proof version).

Data capture foot switch Transfer of measured values 20-28-0125 Connection: 1 x Voltage- free switch (foot switch) Size: Cable length: 2,5 m

Control element to trigger transfer of measured value. Splash-proof version in protection class IP65. Foot switch with Synchro plug to DC-HI-NET with protection class IP65

Product survey 2019

Rev. 31/2019 of 37

17. Control elements for data capture Data capture cable Connector cable for data capture switch 20-28-0100 Connection: 1 x Voltage- free switches (hand /

foot switch, limit switch) Size: Length: 2,5 m

Control element to trigger transfer of measured value via existing synchronization switches. One cable end not wired; other end: Synchro plug to DC-HI-NET.

Manual data capture switch Transfer of measured values 20-28-0110 Connection: 1 x Voltage- free switch (hand

switch) Size: Cable length: 2,5 m

Control element to trigger transfer of measured values Manual switch with Synchro plug to DC-HI-NET

Data capture foot switch Transfer of measured values 20-28-0120 Connection: 1 x Voltage- free switch (foot switch) Size: Cable length: 2,5 m

Control element to trigger transfer of measured value. Foot switch with Synchro plug to DC-HI-NET

Data capture foot switch IP64 Transfer of measured values 20-28-0121 Connection: 1 x Voltage- free switch (foot switch) Size: Cable length: 2,5 m

Control element to trigger transfer of measured value. Version with protection class IP64. Foot switch in protection class IP64 with Synchro plug to DC-HI-NET

Channel selection switch Switch for channel selection 20-28-0181 Connection: 1 x potential-free switch (channel

selection switch) Size: Cable length 2,5 m

8 x channel selection switch for manual channel selection to DC-HI-NET including data transfer button, foot pedal connec-tion and connector to DC-HI-NET (for data transfer channel selection in keyboard code via STEINWALD Software "MessBase light"

18. Cable between "DC-HI-NET" and Host computer PC (9-pin)<->DC-HI-NET Cable to PC 20-28-2821 Connection: 1 x Connection to the PC via serial

interface Size: Length: 2 m

Host connection cable for the serial PC connection via RS232 8- pin round cable, screened, with 9-pin D-Sub connector

PC (9-pin)<->2 x SINGLE x-RS Cable to PC 20-28-2829 Connection: 1 x Connection of 2 DC-HI-NET to

PC via serial interface Size: Length: 2 m

Host computer cable for serial PC connection of 2 DC-HI-NET SINGLE x-RS via RS232 Round cable, shielded, 9-pin D-Sub connector

PC (9-pin)<->SINGLE x-RS Cable to PC 20-28-2818 Connection: 1 x Connection of RS485-BUS to

PC via serial interface Size: Length: 2 m

Host computer cable for serial PC connection via RS485-BUS cascaded DC-HI-NET SINGLE RS devices via RS232, in-cludes adapter RS232<->RS485 Round cable, shielded, 9-pin D-Sub connector

SINGLE x-RS<->SINGLE x-RS Cable between 2 DC-HI-NET SINGLE x-RS 20-28-2819 Connection: 1 x Connection between 2 DC-HI-

NET SINGLE x- RS via RS485 Size: Length: 2 m

Connection cable for serial coupling of two DC-HI-NET SINGLE x-RS via RS485.

USB<->DC-HI-NET Adapter cable RS232/USB 20-00-0306 Connection: 1 x Connection to PC via USB

interface Size: Length 0,8 m

Adapter cable for connecting DC-HI-NET to a PC with USB interface via STEINWALD cable 20-28-2821 (USB driver download at: http://usb.steinwald.com)

Please ask for an offer for customer-specific versions (cable, plug, cable length).

Product survey 2019

Rev. 31/2019 of 37

19. Connection between measurement devices and "DC-HI-NET" MULTI <-> RS232 measurement device Cable for devices with RS232 interface as annexed Connection: 1 x Measurement devices with

RS232 Size: Length: 2 m

Measurement device cable for measurement devices with serial interface (RS232). Select the cable type and the order number from the "List of measurement devices"! With MULTI plug to the interface module

BCD/X <-> BCD measurement device Cable for devices with BCD interface as annexed Connection: 1 x BCD Size: Length: 1,5 m

Measurement device cable for measurement devices with serial or parallel BCD interface. Select the cable type and the order number from the "List of measurement devices"! 36- pin round cable, shielded

OPTO<->MULTI Cable MULTI <-> OPTO devices 20-28-3103 Connection: 1 x OPTO Size: Length: 2 m

Measurement device cable for measurement devices with OPTO data output. With MULTI plug to the interface module

POWER<->MULTI Kabel MULTI <-> POWER devices 20-28-5126 Connection: 1 x POWER Size: Length: 2 m

Measurement device cable for measurement devices with Sylvac-POWER data output. Power sypply of measurement via DC-HI-NET. With MULTI plug to the interface module

PROXIMITY<->MULTI Kabel MULTI <-> PROXIMITY devices 20-28-5134 Connection: 1 x PROXIMITY Size: Length: 2,5 m

Measurement device cable for measurement devices with Sylvac-PROXIMITY data output. With MULTI plug to the interface module

I/O connection Connection plug for SINGLE I/O-USB 20-28-6600 Connection: 1 x Voltage-free switches / relays For connection of digital inputs and outputs.

DC-HI-NET <-> measurement device Customer- specific cable 20-85-0050 Size: to customer specifications

Measurement device cable design in accordance with custom-er specifications. For special modifications. Price on request

Please ask for an offer for customer-specific versions (cable, plug, cable length).

http://dict.leo.org/ende?lp=ende&p=eL4jU.&search=as

http://dict.leo.org/ende?lp=ende&p=eL4jU.&search=annexed

http://dict.leo.org/ende?lp=ende&p=eL4jU.&search=as

http://dict.leo.org/ende?lp=ende&p=eL4jU.&search=annexed

Product survey 2019

Rev. 31/2019 of 37

20. Software Tools "MessBase light" "DC-HI-NET" logging software 20-38-1000

Transfers measurement values of a "DC-HI-NET" interface device connected to the PC-COM interface and sends the values via simulated keystrokes to the active window (application). The program allows the setting of:

■ COM port for interface connection ■ Decimal marker ■ Measurement ending character ■ Measurement channels ■ Timer

"MessBase plus" "DC-HI-NET" logging software 20-38-1010

Example sheet for the transfer of measurement values from "DC-HI-NET" interface devices to Microsoft Excel® Functions:

■ Graphical and numerical online measurement value display ■ Measurement value storage ■ Tolerance monitoring ■ Static and dynamic measurement ■ Measurement cycle planning ■ Channel connections ■ Multi-position measurement including zeroing and offset function

DCDemo32 Diagnostics software 20-30-9920 Software for system test independent from the application

software (real-time presentation of measured values on PC monitor). For MS-Windows / Linux Download: http://www.steinwald.com/software/DCDemo32.exe

Windows driver DLL "DC-HI-NET" driver software 20-30-9953 Software for reading measured values from DC-HI-NET inter-

faces into Windows® 2000 / XP / Vista / 7 / 8 (32 Bit) applica-tions. DC-HI-NET device driver in form of a 32 bit DLL (64 bit version on request). Incl. manual and sample programs.

Product survey 2019

Rev. 31/2019 of 37

21. Services Man-day In-house software driver modification 20-30-9900 Service for interface development and test in accordance with

customer-specific requirements. Charge according to the required effort.

Working time on-site Engineer working hour on-site 40-05-0200 Service for software modifications, installation support, installa-

tion and test at customer locations. Charge according to the required effort.

Travelling hour Engineer travelling hour 40-08-0700 Service covering the journey for on-site customer support.

Charge according to the required effort.

Journey kilometer Company car 40-08-0500 Service covering the journey for on-site customer support.

Charge according to the required effort.

Interface analysis Preparation of interface adaptations 20-30-9902 Service including procurement and analysis of measurement

device manufacturer´s documentation for interface adapta-tions. Documentation may also be provided by the customer.

Device loan Device loan flat rate DC-HI-NET 20-35-0003 Service on request up to 6 week loan (e.g. for test installa-

tions), incl. customer-specific configuration, dispatch and packaging.

Update firmware Update of firmware 20-30-9931 Service for the implementation of new software releases into

DC-HI-NET. Please provide the device serial number when ordering!

Product survey 2019

Rev. 31/2019 of 37

22. Terms and conditions PRICES All prices are in EURO FCA / DAP (INCOTERMS 2010) excluding packaging, transport insurance and VAT.

TERMS OF PAYMENT Initial delivery: COD. Payment within 14 days: net.

DELIVERY TIMES Standard equipment: 1-2 weeks after order Special modifications: 6-8 weeks after order

CUSTOMER CARE AND WARRANTY Prior to delivery, all devices have to pass extensive quality control and burn-in tests.

Warranty

STEINWALD datentechnik GmbH (STEINWALD) assures the customer that the listed products are free from defects in material and workmanship during the 12-month warranty period as of the date of delivery. In the case of software products, the manufacturer warranty only applies in the event of errors arising while running the programming instructions. STEINWALD does neither guarantee interruption-free nor error-free operation of a software product. The manufacturer warranty only applies to defects occurring during proper use of the product and does not include: • improper or insufficient maintenance or modification of devices. • consumable items or accessories which were not supplied by STEINWALD. • operation outside the product’s specifications. If STEINWALD is unable to repair or replace a defective product covered by the manufacturer warranty, STEINWALD shall refund the purchase price for the product within a reasonable time after being notified of the defect. STEINWALD shall have no obligation to repair, replace or refund, until the customer returns the defec-tive product to STEINWALD. Replacement products may be in either new or new-like condition, provided they have a functionality that is at least equal to the product being replaced. Further customer care or warranty services (e.g. on-site service, service maintenance contract, hotline) may be agreed between the customer and STEINWALD.

Limitation of liability

With the exception of the obligations expressly stated in this manufacturer warranty, and to the permissible ex-tent under applicable law, neither STEINWALD nor its suppliers and dealers are liable to replace a product in the event of direct, indirect or accidental damage incurred, irrespective of whether this damage is claimed on the basis of agreements, unlawful acts or other legal measures, and irrespective of whether or not STEINWALD or its suppliers and dealers were notified of the possibility of such damage. Service STEINWALD offers repair and replacement services (on request). In the case of repair services, send a defec-tive component to STEINWALD, which will be repaired and returned in reasonable time. In the case of replace-ment services, notify STEINWALD, on the phone or in writing, of the exact type of the defective component, and

Product survey 2019

Rev. 31/2019 of 37

send the component in question to STEINWALD. Nearly at the same time, STEINWALD will then send you a component of the same functionality, which you can immediately integrate into your system. Repair services are free during the warranty period. After the warranty period, material costs and working hours are charged. Once the warranty period has expired, the current list prices are charged for replacement compo-nents.

The manufacturer reserves the right to make changes!

STEINWALD datentechnik GmbH Oskar-Loew-Strasse 12 / D-95615 MARKTREDWITZ

Tel. +49 9231 9630-10 Fax +49 9231 9630-11 e-mail: [email protected] http://www.steinwald.com

Product survey 2019

Rev. 31/2019 of 37

23. List of measurement devices The following list contains an excerpt from our measurement devices database of measurement device connec-tions that have already been implemented. In order to make a firm offer, we do, however, require specifications on your means of measuring and measuring data, since we cannot provide an exhaustive list of all device ver-sions and customer-specific measurement device types in this overview. Measurement devices listed for interface module "MULTI-X" may be connected to the "DC-HI-NET" devices "SINGLE M4/8/INDM8-RS", "SINGLE M1/2/4/8-USB" as well as to the "SINGLE M1/3/6-K". The designation "RS232 C/XXX" stands for the number of the RS232 driver, which was programmed by STEINWALD, and is available at the "MULTI" interface models "SINGLE x-USB/RS" as well as at the "SINGLE x-K" (restricted). Manufacturer Measurement device Type Interface / driver Cable A&D Balance GX/GF series RS232 C/U4 20-28-5031 ACCRETECH TOKYO SEIMITSU Surface measuring gauge SURFCOM NEX RS232 C/700 20-28-3137 AEROEL Laser Micrometer XLS40 RS232 C/U4 20-28-5147 AHLBORN Measuring instrument ALMEMO 2590-3S RS232 C/497 20-28-5021 AHOTEC Hardness Testing Panel UHP-1 RS232 C/U4 20-28-5147 AKASHI Hardness Tester ASK-510 RS232 C/U4 20-28-5167 ALLURIS Force gauge FMT-110WT RS232 C/348 20-28-5105 ALTHEN Display Unit PAX S RS232 C/437 20-28-5058 ATEQ Flow Analyser ATEQ D520 RS232 C/41 20-28-5147 ATEQ Leak detector F 520 RS232 C/539 20-28-3137 ATLAS COPCO Tigthening controller PowerFocus 4000 Compact RS232 C/575 20-28-5003 ATLAS COPCO Tigthening controller PowerFocus SL Graph RS232 C/575 20-28-5007 ATORN Hand tools "multiCOM" interface MULTI-X 20-28-5110 AVERY BERKEL Balance TA series RS232 C/U4 20-28-5058 BAHCO Torque tool IZO-DM/DFM RS232 C/U4 20-28-5058 BALLUFF inductive sensor BES 516-370-G-E5-Y-S4 I/O not required BAQ Hardness Tester alphaDUR II RS232 C/U4 20-28-3137 BAREISS Hardness Tester HHP-2001 RS232 C/U4 20-28-5054 BETA LASERMIKE Laser micrometer Model 1200 RS232 C/73 20-28-5069 BETA LASERMIKE Laser micrometer BenchMike model 4025/4050 RS232 C/U4 20-28-5058 BIZERBA Balance Type EL RS232 C/U4 20-28-5003 BIZERBA Balance GE series RS232 C/U4 20-28-3133 BIZERBA Balance ITC-B / ITC-R RS232 C/U4 20-28-5003 BIZERBA Balance SL series RS232 C/2 20-28-5062 BIZERBA Industry terminal ST/ST-EX RS232 C/422 20-28-5058 BÖHM Force gauge WG 3/2; 3/3; 4/2; 4/3; 27 RS232 C/133 20-28-5148 BÖHM Force gauge WG 23/13, WG 3/3, 4/3 sBCD/2 20-28-6004 BÖHM Spring Tester AFP series RS232 C/370 20-28-3137 BOSCH Tigthening controller SE 200 RS232 C/306 20-28-5031 BOWERS Bore Gauge XT3 MULTI-X 20-28-5134 BOWERS Bore Gauge XT-XTREME MULTI-X 20-28-5126 BURSTER DIGIFORCE 9306 RS232 C/445 20-28-5058 BÜ-TEC Test stand bue-fix opto PS RS232 C/393 20-28-3137 BYK-GARDNER Gloss measurement micro-Gloss RS232 C/61 20-28-3137 BYK-GARDNER Color measurement Spectro-Guide RS232 C/272 20-28-5058 CALIPER Video Measuring Microscope Magellan V-200 RS232 C/558 20-28-3137 CHATILLON Force gauge Model DFI MULTI-X 20-28-5046 CHATILLON Force gauge Model DFS MULTI-X 20-28-5046 CMC-KUHNKE DIG II Enamel Rater RS232 C/U4 20-28-5147 CMC-KUHNKE Seam Inspection System SEAMVIEW PRO RS232 C/568 20-28-3137 COLORLITE Spectralphotometer sph860 / sph900 RS232 C/623 20-28-5147 DATACOLOR Color measurement ELREPHO 2000 RS232 C/106 20-28-3133 DEFELSKO Coating thickness gauge 6000 RS232 C/U4 20-28-5043 DELCAM Measuring software PowerINSPECT RS232 C/370 20-28-3137 DELTRONIC Display Unit MPC-5 RS232 C/300 20-28-5135 DENVER INSTRUMENT Balance APEX series RS232 C/2 20-28-3137 DEPRAG Tigthening controller AST 10 RS232 C/606 20-28-5193 DESOUTTER Tigthening controller CVIL II / III RS232 C/605 20-28-3137 KARL DEUTSCH Coating thickness gauge LEPTOSKOP 2042 RS232 C/604 20-28-5191 DIATEST 4 (8) chanal display unit DIATRON 5000 PLUS RS232 C/331 20-28-5058 DINI ARGEO Balance GAEP-K series RS232 C/680 20-28-5147 DL-SYSTEME leak test system LTG 750 RS232 C/U4 20-28-3137 EASYDUR Spring Tester "PC" series RS232 C/U4 20-28-5167 EDMUNDS GAGES Measuring column Accu-Setter II RS232 C/433 20-28-5003 EKU ELEKTRONIK Ventilator tester CALIBSO RS232 C/701 20-28-3137 ELCOMETER Coating thickness gauge 456 C RS232 C/U4 20-28-3137

Product survey 2019

Rev. 31/2019 of 37

Manufacturer Measurement device Type Interface / driver Cable ELEKTRO-PHYSIK Wall Thickness Gauge MiniTest 7000 series RS232 C/U4 20-28-5144 ELEKTRO-PHYSIK Coating thickness gauge eXacto F RS232 C/U4 20-28-5089 ELGO Display Unit IZ16E-100 RS232 C/678 20-28-5227 ELGO Position Display Unit Z58-6XX RS232 C/451 20-28-5058 EmcoTest Hardness Tester Emcotest M4 RS232 C/166 20-28-5003 EmcoTest Hardness Tester DuraVision 20 RS232 C/U4 20-28-3137 EmcoTest Hardness Tester DuraJet RS232 C/591 20-28-3137 ERICHSEN Display Unit 975 AP RS232 C/U4 20-28-5213 ERICHSEN Force gauge Model 708 MULTI-X 20-28-5096 ERNST Hardness Tester AT130D / NR3D RS232 C/U4 20-28-3137 ESI Prüftechnik Measurement electronics FME6 RS232 C/589 20-28-5092 ESITRON Position Display Unit AM10 RS232 C/562 20-28-5147 FAGOR Position Display Unit NV RS232 C/455 20-28-3133 FAGOR Linear Encoder MOP series INCx not required FARO Measuring software Gage RS232 C/503 20-28-3137 FEINMESS SUHL Micrometer Series 518 MULTI-X 20-28-3103 FISCHER DUALSCOPE MP4/MP40 RS232 C/U4 20-28-3140 FISCHER DUALSCOPE MP0R RS232 C/U4 20-28-5121 FISCHER DUALSCOPE FMP30/40 RS232 C/U4 20-28-3140 FISCHER FISCHERSCOPE MMS PC RS232 C/U4 20-28-3137 FISCHER ISOSCOPE MP30E-S RS232 C/U4 20-28-3140 FLEXIM Flowmeter FLUXUS F721 RS232 C/697 20-28-5216 FLUKE Digital Multimeter 8840/8842 A IEEE/2 20-28-6022 FLUKE Digital Multimeter 8845A/8846A RS232 C/675 20-28-3137 FLUKE RCL Meter PM 6304 / PM6306 RS232 C/456 20-28-3137 FORM+TEST Testing machine 20 EM RS232 C/524 20-28-5105 FOWLER Caliper ProMax-Cal MULTI-X 20-28-3103 FRANK Smoothness Tester PTA Line Bek RS232 C/512 20-28-3137 FURNESS CONTROLS Leak Detector Calibrator FCO 730 RS232 C/U4 20-28-3137 GALDABINI Measuring software LabTest RS232 C/702 20-28-3137 GENERAL INSPECTION Measuring software LaserLab RS232 C/547 20-28-3137 GIGAHERTZ-OPTIK Light meter X9 RS232 C/620 20-28-5058 GOSSEN-METRAWATT Milliohmmeter METRAHit M RS232 C/584 20-28-5133 GRETAG-MACBETH Densitometer D200-II RS232 C/U4 20-28-5031 GRUNDIG RLC-Meter RLC 200 RS232 C/566 20-28-5172 HAMEG Power-Meter HM 8115-2 RS232 C/559 20-28-5058 HBM Amplifier MGCplus RS232 C/450 20-28-5165 HBM Amplifier SCOUT55 RS232 C/U4 20-28-5113 HEGEWALD & PESCHKE Hardness Tester AT 350 RS232 C/U4 20-28-3137 HEGEWALD & PESCHKE Measuring software LabMaster RS232 C/U4 20-28-3137 HEGEWALD & PESCHKE Measuring software LabMaster RS232 C/241 20-28-3137 HEIDENHAIN Length Gauges MT series INCx 20-28-3354 HEIDENHAIN Length Gauge ST 1207 / 1208 INCx not required HEIDENHAIN Display Unit ND 221/231/261/280/281 RS232 C/5 20-28-3133 HEIDENHAIN Display Unit ND 282/286 BCD-36 20-28-2526 HEIDENHAIN Position Display Unit ND 287 RS232 C/5 20-28-5081 HEIDENHAIN Position Display Unit ND 1100 QUADRA-CHEK RS232 C/349 20-28-5105 HEIDENHAIN Position Display Unit ND 1200 QUADRA-CHEK RS232 C/316 20-28-5105 HEIDENHAIN Position Display Unit ND 1300 QUADRA-CHEK RS232 C/488 20-28-5105 HEIDENHAIN Position Display Unit ND 2100 G GAGE-CHEK RS232 C/349 20-28-5105 HELIOS Hand tools "Opto RS-232" interface MULTI-X 20-28-3103 HELIOS Display Unit UNITRON 2 CHA RS232 C/189 20-28-5021 HELIOS-PREISSER "Integrated Wireless" Series "i" x-IW2 not required HELIOS-PREISSER Hand tools "DATA VARIABLE" interface MULTI-X Preisser-Digimatic HENGSTLER Counter signo 724 RS232 C/365 20-28-5076 HEWLETT-PACKARD Multimeter HP 34401 A IEEE/1 20-28-3077 HEXAGON Measuring software PC-DMIS RS232 C/U4 20-28-3137 HIOKI Battery HiTester BT3560 RS232 C/684 20-28-5147 HIOKI Battery HiTester BT3562 RS232 C/684 20-85-0050 HIRT Inductive Probe Halfbridge IND-X Not required HOFFMANN Caliper 41 2680 150 MULTI-X 20-28-5134 HOFFMANN Video Measuring Microscope Garant MM1 / MM2 RS232 C/572 20-28-3137 JENOPTIK Surface measuring gauge HOMMEL TESTER T500 RS232 C/154 20-28-5151 JENOPTIK Surface measuring gauge HOMMEL TESTER T1000 II RS232 C/219 20-28-3137 JENOPTIK Surface measuring gauge HOMMEL-ETAMIC W5 RS232 C/219 20-28-3137 JENOPTIK Surface measuring gauge HOMMEL-ETAMIC W20 RS232 C/U4 20-28-3137 JENOPTIK Measuring software OPTIC-Line Contour 414 RS232 C/493 20-28-3137 JENOPTIK universal analyzer CMZ200 RS232 C/508 20-28-3137 IMADA Force gauge DPS series MULTI-X from IMADA IMADA Force gauge ZT series MULTI-X from IMADA IMESS Measuring software RS232 C/683 20-28-3137 INDUK ForceInspect FI 108/109 RS232 C/458 20-28-5157 INDUK Display Unit Model AP 780 RS232 C/635 20-28-5129

Product survey 2019

Rev. 31/2019 of 37

Manufacturer Measurement device Type Interface / driver Cable INSIGHT METROLOGY Measuring software CMM-Manager RS232 C/709 20-28-3137 INSTRON Measuring software Bluehill Testing RS232 C/454 20-28-3137 IST Measuring software TT3 RS232 C/426 20-28-3137 KB Prüftechnik Measuring software KB HARDWIN RS232 C/U4 20-28-3137 KB Prüftechnik Hardness Tester KB 250 RS232 C/U4 20-28-3137 KEITHLEY Digital Multimeter DMM 2000 RS232 C/137 20-28-5058 KERN Balance Series 440 RS232 C/U4 20-28-5058 KERN Balance Series 470 RS232 C/U4 20-28-5102 KERN Balance Series 572 RS232 C/U4 20-28-5058 KERN Balance ABS/ABJ RS232 C/U4 20-28-3133 KERN Balance ALJ/ALS RS232 C/U4 20-28-5058 KERN Balance ARJ-/ARS-/PRJ-/PRS-Serie RS232 C/U4 20-28-5142 KERN Balance EW/EG-N-balances RS232 C/U4 20-28-5064 KERN Balance FTB RS232 C/6 20-28-5058 KERN Precision balance PES / PEJ RS232 C/U4 20-28-3137 KERN Precision balance PLS/PLJ/PLB RS232 C/U4 20-28-3137 KERN Moisture analyzer MLS-D RS232 C/660 20-28-5147 KERN Moisture analyzer MRS RS232 C/581 20-28-5142 KEYENCE Vision measuring system CV-3000 series RS232 C/468 20-28-5141 KEYENCE Vision measuring system CV-5000 series RS232 C/468 20-28-5141 KEYENCE Profile projector IM-6xxx series RS232 C/532 20-28-3137 KEYENCE Optical Comparator IM-7000 series RS232 C/532 20-28-3137 KEYENCE 2D Laser Displacement Sensor LJ-G series RS232 C/637 20-28-5141 KEYENCE Laser Displacement Sensor LK-G series RS232 C/486 20-28-5141 KEYENCE Laserscan Micrometer LS-7000 series RS232 C/439 20-28-5122 KEYENCE Optical micrometer LS-9000 series RS232 C/627 20-28-5141 KEYENCE 2D Measurement Sensor TM-3000 series RS232 C/627 20-28-5141 KEYENCE 3D-Profilometer VR-3000 series RS232 C/681 20-28-3137 KEYENCE Vision measuring system XG-8000 series RS232 C/595 20-28-5141 KEYENCE 3D Measurement System XM series RS232 C/532 20-28-3137 KEYENCE RS232C communication unit DL-RS1 RS232 C/486 20-28-5113 KISTLER Charge Master Type 5015 RS232 C/613 20-28-5003 KNÄBEL Inductive Probe IET IND-X Connector AK 02.1 KONICA MINOLTA Spectrophotometer CM-700d RS232 C/565 20-28-3137 KONICA MINOLTA Spectrophotometer CM-2500c RS232 C/565 20-28-3137 KORDT Display Unit CORD 13000 A1 RS232 C/616 20-28-5058 KRAUTKRAMER Thickness gage DM4-DL RS232 C/363 20-28-5090 KRAUTKRAMER Thickness gage DMS 2 RS232 C/363 20-28-5111 KROEPLIN External Quicktest B series MULTI-X from Kroeplin KROEPLIN Internal Quicktest F series MULTI-X from Kroeplin KROEPLIN Internal measurement G series MULTI-X from Kroeplin KRÜSS Digital Abbe refractometer AR2008 RS232 C/515 20-28-5117 KRÜSS Mobile Surface Analyzer ADVANCE-Software RS232 C/695 20-28-3137 Kübler LCD Preset Counter Codix 560 RS232 C/U4 20-28-5058 LEYBOLD Helium Leak Detector PhoeniXL 300 RS232 C/516 20-28-5058 LLOYD Measuring software NEXYGEN RS232 C/U4 20-28-3137 LORENTZEN & WETTRE Tensile Tester Code 062 M RS232 C/527 20-28-5003 LORENZ MESSTECHNIK Amplifier GM 80-TG/-PA RS232 C/597 20-28-5058 L.O.T. Laser micrometer Model 1200 RS232 C/73 20-28-5069 MACHEREY-NAGEL Photometer NANOCOLOR PF12 plus RS232 C/689 20-28-3137 MAGNET-PHYSIK Dr. Steingroev. Fluxmeter EF 14 RS232 C/563 20-28-5147 MAHR Integrated Wireless i-wi x-IW2 not required MAHR Hand tools "MarConnect" interface MULTI-X Mahr-Digimatic MAHR Hand tools "Opto RS-232" interface MULTI-X 20-28-3103 MAHR Dial Gage µMaxµm XL MULTI-X 20-28-5085 MAHR Height Gauge DIGIMAR 816 CL MULTI-X 20-28-5060 MAHR Height Gauge DIGIMAR 817 CLM MULTI-X 20-28-5007 MAHR Height Gauge DIGIMAR CX1 RS232 C/U4 20-28-5007 MAHR Height Gauge DIGIMAR CX2 RS232 C/U4 20-28-5007 MAHR Inductive Probe Halfbridge IND-X not required MAHR Inductive Probe Fullbridge IND-X not required MAHR Length Measuring Instrument Millimar C 1208 RS232 C/438 20-28-3137 MAHR Length Measuring Instrument Millimar C 1210 RS232 C/438 20-28-3137 MAHR Length Measuring Instrument Millimar C 1245 RS232 C/438 20-28-3137 MAHR Length Measuring Instrument Millimar C1504 RS232 C/U4 20-28-5011 MAHR Column amplifier Millimar S 1840 RS232 C/50 20-28-3137 MAHR Perthometer M1/M2/M3 RS232 C/24 20-28-3137 MAHR MarSurf M 300 RS232 C/594 20-28-5190 MAHR MarSurf M 400 RS232 C/594 20-28-5190 MAHR MarSurf PS 1 MULTI-X 20-28-5110 MAHR MarSurf XR 1 RS232 C/625 20-28-3137 MAHR MarSurf GD 26 RS232 C/625 20-28-3137 MAHR Formtester MMQ 10 RS232 C/179 20-28-3137

Product survey 2019

Rev. 31/2019 of 37

Manufacturer Measurement device Type Interface / driver Cable MAHR Formtester MMQ 100 RS232 C/579 20-28-3137 MAHR Measuring Microscope MarVision QM 300 RS232 C/370 20-28-3137 MAHR Measuring software MarSurf Rev. 1.6 RS232 C/540 20-28-3137 MAHR Measuring software MarSurf XCR 20 RS232 C/639 20-28-3137 MAHR Measuring and evaluation unit MarCheck - LINEAR RS232 C/61 20-28-5183 MARK-10 Force gauge Model BG / BGI MULTI-X 20-28-5119 MARPOSS Inductive Probe Halfbridge IND-X Not required MARPOSS Inductive Probe Fullbridge IND-X not required MARPOSS Manual bore gauge M1 IND-X not required MARPOSS Display Unit E4N MULTI-X 20-28-5070 MARPOSS Gauge computer MERLIN RS232 C/706 20-28-3137 MARUI-KEIKI Protractor DP-601 MULTI-X von MARUI-KEIKI MAV Digital Tester Model FT - FTS - FTM RS232 C/431 20-28-5099 MAVOMATIC Display Unit PEL-Kolibri AA03A05 RS232 C/661 20-28-5058 MECMESIN Force gauge AFG series MKI MULTI-X 20-28-5016 MECMESIN Force gauge AFG-/AFTI series MKII MULTI-X 20-28-3120 MECMESIN Force gauge AFG-/BFG series MKIII MULTI-X 20-28-5106 MECMESIN Force gauge AFG-/BFG series MK IV MULTI-X 20-28-5127 MECMESIN Force gauge MFG series MULTI-X 20-28-5005 MECMESIN Test stand MultiTest-d RS232 C/649 20-28-5058 MEGATRON Display Unit Series MODIG 10X-V5 RS232 C/549 20-28-5113 MERCER Inductive Probe Halfbridge IND-X not required MERCER Inductive Probe Fullbridge IND-X not required METLOGIX Measuring software M3 RS232 C/370 20-28-3137 METRO Display Unit M1-M3 RS232 C/670 20-28-5003 METROHM Titrator Titrino DMS 716 RS232 C/423 20-28-5019 METROHM Titrator 916 Ti-Touch RS232 C/708 20-28-3137 METRONICS Display Unit QUADRA-CHEK 100 RS232 C/349 20-28-5105 METRONICS Display Unit QUADRA-CHEK 200 RS232 C/316 20-28-5105 METRONICS Display Unit QUADRA-CHEK 300 RS232 C/488 20-28-5105 METRONICS Display Unit GAGE-CHEK RS232 C/349 20-28-5105 METTLER TOLEDO Weighing Terminal ICS4x5 RS232 C/6 20-28-5169 METTLER TOLEDO Weighing Terminal ICS4x9 RS232 C/6 20-28-5169 METTLER TOLEDO Weighing Terminal ID7 RS232 C/6 20-28-5091 METTLER TOLEDO Weighing Terminal IND690 RS232 C/6 20-28-5091 METTLER TOLEDO Weighing Terminal Spider FC / BC / SW RS232 C/6 20-28-5058 METTLER TOLEDO Balance AB line RS232 C/U4 20-28-5011 METTLER TOLEDO Balance BBA-/BBK series RS232 C/6 20-28-5058 METTLER TOLEDO Moisture Analyzer Excellence plus HX204 RS232 C/443 20-28-5011 METTLER TOLEDO Basic Scale ICS241 RS232 C/6 20-28-5147 METTLER TOLEDO Precision balance ME / ME-E RS232 C/6 20-28-5011 METTLER TOLEDO Analytical Balance ML series RS232 C/6 20-28-5011 METTLER TOLEDO Semi-Micro Balance MS RS232 C/6 20-28-5011 METTLER TOLEDO Precision Balance MS-S / MS-L RS232 C/6 20-28-5011 METTLER TOLEDO Analytical Balance MS-TS RS232 C/6 20-28-5011 METTLER TOLEDO Balance MX/UMX series RS232 C/6 20-28-5011 METTLER TOLEDO Precision Balance PB-L RS232 C/6 20-28-5011 METTLER TOLEDO Balance PB-/SB line RS232 C/6 20-28-5011 METTLER TOLEDO Balance PB-XXXX-S-Linie RS232 C/U4 20-28-5011 METTLER TOLEDO Balance PG-/SG line RS232 C/6 20-28-5011 METTLER TOLEDO Portable Balances PL-E RS232 C/6 20-28-5011 METTLER TOLEDO Balance PL-/PL-S series RS232 C/6 20-28-5011 METTLER TOLEDO Balance VIPER BC RS232 C/6 20-28-5058 METTLER TOLEDO Balance VIPER SW RS232 C/6 20-28-5058 METTLER TOLEDO Precision balance XP series RS232 C/6 20-28-5011 METTLER TOLEDO Micro-analytical Balance XPE RS232 C/6 20-28-5011 METTLER TOLEDO Precision balance XS series RS232 C/6 20-28-5011 MICRO-EPSILON CCD sensor optoNCDT 1402 RS232 C/U4 20-28-5130 MICRO-EPSILON scanCONTROL 26xx / 29xx RS232 C/704 20-28-5216 MicroStudio Spring Tester PMZ2-600 RS232 C/U4 20-28-3137 MicroStudio Spring Tester LED2D RS232 C/U4 20-28-3137 MicroStudio Measuring software PMA-R RS232 C/U4 20-28-3137 MICRO VU Measuring software InSpec (Manual/Vision) RS232 C/560 20-28-3137 MITUTOYO Hand tools "DIGIMATIC" interface MULTI-X from Mitutoyo MITUTOYO Length Measuring Instrument Linear Gage LGS MULTI-X from Mitutoyo MITUTOYO Height Gauge Linear Height LH-600 C/CG RS232 C/U4 20-28-3137 MITUTOYO LaserScan Micrometer LSM-6000/6000S RS232 C/U4 20-28-3137 MITUTOYO Display Unit ALC-1705W RS232 C/56 20-28-5117 MITUTOYO Display Unit EH-102D RS232 C/685 20-28-5081 MITUTOYO Display Unit Type KA 2xx RS232 C/56 20-28-5117 MITUTOYO Display Unit Typ KS, series 174 RS232 C/56 20-28-5117 MITUTOYO Display Unit QM-Data 100 RS232 C/U4 20-28-3137 MITUTOYO Display Unit QM-Data 200, series 264 RS232 C/432 20-28-3137

Product survey 2019

Rev. 31/2019 of 37

Manufacturer Measurement device Type Interface / driver Cable MITUTOYO Measuring Microscope MF series generation D RS232 C/56 20-28-5007 MITUTOYO Measuring Projector PJ-3005 F-150 MULTI-X 20-28-5174 MITUTOYO Measuring Projector PJ-A3000 series RS232 C/397 20-28-5081 MITUTOYO Measuring Projector PJ-5010 RS232 C/56 20-28-5117 MITUTOYO Measuring software MCOSMOS V3 RS232 C/122 20-28-3137 MITUTOYO Vision measuring system QUICK-SCOPE RS232 C/U4 20-28-3137 MITUTOYO Optical measuring system QVA 250 PT/TP RS232 C/364 20-28-3137 MITUTOYO Measuring software QV-PAK RS232 C/U4 20-28-3137 MITUTOYO Contour Measurement CV-1000 RS232 C/513 20-28-3137 MITUTOYO Surface measuring gauge Surftest SJ-201 MULTI-X from Mitutoyo MITUTOYO Roughness Measuring Instrument Surftest SV-3200 RS232 C/682 20-28-3137 NEWPORT Display Unit INFS RS232 C/U4 20-28-5057 NEWPORT Display Unit INF8-C RS232 C/U4 20-28-5057 NIKON Display unit SC-112 / SC-113 RS232 C/35 20-28-3133 NIKON Measuring Microscope Serie MM RS232 C/35 20-28-3133 NIKON Measuring Microscope MM-400/800 RS232 C/343 20-28-3137 NIKON Profile projector V-20B RS232 C/35 20-28-3137 NIKON Measuring software NEXIV VMR RS232 C/402 20-28-3137 NIKON Measuring software VMR 2520 RS232 C/402 20-28-3137 OBLF Spectrometer SPECTROLAB RS232 C/261 20-28-3137 OGP Measuring software SmartScope MVP 250 RS232 C/366 20-28-3137 OGP Measuring software MeasureMind+ Ver. 10 RS232 C/366 20-28-3137 OHAUS Balance Adventurer series AR RS232 C/420 20-28-5182 OHAUS Balance Scout PRO series RS232 C/U4 20-28-5058 OHAUS Balance Voyager PRO series RS232 C/420 20-28-5207 OKM Coordinate Meas. Machine UNI-VIS 250 RS232 C/335 20-28-3137 OLYMPUS Magna-Mike Model 8600 RS232 C/341 20-28-5195 PANAMETRICS MAGNA-MIKE Model 8500 RS232 C/341 20-28-5094 PANAMETRICS Thickness gage Model 36DL plus RS232 C/U4 20-28-5094 PANAMETRICS Corrosion analyzing instrum. Model 37DL RS232 C/341 20-28-5045 PAV Hand tools "PROXIMITY" interface MULTI-X 20-28-5134 PAV Hand tools "DIGIMATIC" interface MULTI-X PAV-DIGIMATIC PCE Force gauge FM200 RS232 C/588 20-28-5186 PFEIFFER VACUUM SmartTest HLT 550/560/570 RS232 C/641 20-28-5058 PHYNIX Coating thickness gauge Surfix RS232 C/501 20-28-5146 PRECISA Balance BJ210C RS232 C/U4 20-28-5142 PRECISA Balance Series 320 XB RS232 C/U4 20-28-5142 PRECITEC Coating thickness gauge CHRocodile S RS232 C/669 20-28-5058 QNESS Micro hardness tester Q10 A+ RS232 C/629 20-28-3137 QNESS Micro hardness tester Q10/30/60M RS232 C/641 20-28-3137 QNESS Hardness tester Q250/750/3000 C/CS RS232 C/687 20-28-3147 RAYTEK Infrared temperature sensor CM RS232 C/421 20-28-5058 REICHERTER ELASTICOMETER EE1-2001 BCD-36/20 20-28-6026 RHEWA Analytical device 83 plus RS232 C/521 20-28-5045 RHEWA Analytical device 83sigma RS232 C/U4 20-85-5113 RÖNTGENANALYTIK Coating thickness gauge ComPact 5 RS232 C/391 20-28-3137 RSF ELEKTRONIK Position Display Unit Z 300 RS232 C/380 20-28-3137 RSF ELEKTRONIK Counter Z 715 RS232 C/5 20-28-5078 SALTUS Torque tool DAZ RS232 C/387 20-28-5100 SARTORIUS Balance BP series RS232 C/2 20-28-5062 SARTORIUS Balance CP-/GC-/GP series RS232 C/2 20-28-5062 SARTORIUS Balance CPA-/GCA-/GPA series RS232 C/2 20-28-5062 SARTORIUS Indicator Combics 1 IP44 RS232 C/2 20-28-5049 SARTORIUS Indicator Combics 1 IP67 RS232 C/2 20-28-5049 SARTORIUS Indicator Combics 2 IP44 RS232 C/2 20-28-5049 SARTORIUS Indicator Combics 3 IP44 RS232 C/2 20-28-5049 SARTORIUS Lab balance Cubis MSA / MSE / MSU RS232 C/2 20-28-5062 SARTORIUS Balance EA-/EB series RS232 C/2 20-28-5062 SARTORIUS Balance Extend ED / GK / GW RS232 C/2 20-28-5062 SARTORIUS Balance Entris series RS232 C/2 20-28-5062 SARTORIUS Balance LP series RS232 C/2 20-28-5062 SARTORIUS Balance MC RS232 C/2 20-28-5049 SARTORIUS Balance Midrics1 RS232 C/C2 20-28-5062 SARTORIUS Balance Midrics2-MW2 RS232 C/2 20-28-5062 SARTORIUS M-Prove Balances AY series RS232 C/2 20-28-5058 SARTORIUS Painting-Mixing Scale PMA RS232 C/U4 20-28-5147 SARTORIUS Balance Practum series RS232 C/2 20-28-5058 SARTORIUS Balance Quintix series RS232 C/2 20-28-5058 SARTORIUS Lab balance Secura series RS232 C/2 20-28-5058 SARTORIUS Balance Signum 2 RS232 C/2 20-28-5062 SARTORIUS Balance Signum 3 RS232 C/2 20-28-5062 SARTORIUS Balance TE series RS232 C/2 20-28-5062 SARTORIUS Moisture tester MA-30/40/60 RS232 C/274 20-28-5062

Product survey 2019

Rev. 31/2019 of 37

Manufacturer Measurement device Type Interface / driver Cable SARTORIUS Moisture tester MA35M RS232 C/274 20-28-5062 SAS Spring Tester CT Series RS232 C/370 20-28-3137 SAUTER Digital force gauge FH series RS232 C/612 20-28-5105 SCALTEC Balance SBA 31/32/33 RS232 C/2 20-28-5062 SCHATZ Torque/rotation angle Mesureme Mod. 5413-2025GX-L1 RS232 C/470 20-28-5162 SCHATZ Torque checker INSPECTpro RS232 C/650 20-28-5147 SCHENCK Balancing machine CAB 641 RS232 C/U4 20-28-5117 SCHLEICH Function tester GLP1-e L RS232 C/480 20-28-3137 DR. SCHNEIDER Display Unit Multicount 3000 RS232 C/488 20-28-5105 DR. SCHNEIDER Measuring software Saphir RS232 C/514 20-28-3137 SENSOR INSTRUMENTS Color measurement SPECTRO-3-30-POL RS232 C/607 20-28-5196 SHIMADZU Hardness Tester HMV 2000 RS232 C/96 20-28-3133 SHIMADZU Balance BL series RS232 C/U4 20-28-3133 SHIMPO INSTRUMENTS Force gauge FGC series RS232 C/348 20-28-5123 SIEMENS SPS Simatic S7 RS232 C/379 20-28-3137 SIKO Display Unit MA100/1 RS232 C/309 20-28-5113 SIKORA Controller REMOTE 2000 RS232 C/447 20-28-5113 SIP Measuring mashine SIP-301/302/305 RS232 C/U4 20-28-3133 SOEHNLE Display Unit S20 model 2760/2761/276x RS232 C/377 20-28-5101 SOEHNLE Weighing Terminal 3010 / 3011 / 3015 RS232 C/377 20-28-5215 SOLARTRON Inductive Probe Halfbridge IND-X not required SOLARTRON Inductive Probe Fullbridge IND-X not required SOLARTRON Digital probes DJ/DP/DT RS232 C/199 20-28-5058 SOLARTRON Linear Encoder LE RS232 C/199 20-28-5058 SOLARTRON Display Unit C/55 RS232 C/U4 20-28-5003 SOLEX Flow Analyser DBE 021 RS232 C/U4 20-28-3133 SONY / MAGNESCALE Display Unit LT10-105C/205C RS232 C/495 20-28-5067 SONY / MAGNESCALE Display Unit LT30 RS232 C/45 20-28-5067 SONY / MAGNESCALE Counter Unit LY51 RS232 C/342 20-28-5067 SONY / MAGNESCALE Counter Unit LY72 RS232 C/342 20-28-5117 SOURCETRONIC DC Resistance Meter ST2515 RS232 C/693 20-28-5147 SOURCETRONIC LCR-Meter ST2810D RS232 C/633 20-28-3137 STANLEY Tigthening Controller QA ALPHA RS232 C/640 20-28-3137 STIEFELMAYER Hardness Tester UH3 RS232 C/504 20-28-3137 STIEFELMAYER Display Unit HME5 RS232 C/351 20-28-3137 STOTZ Air Electronic Column MSG-32 / MSG-64 RS232 C/241 20-28-3137 SYLVAC Wireless interface BT x-IW1 not required SYLVAC Hand tools "OPTO" interface MULTI-X 20-28-3103 SYLVAC Hand tools "POWER" interface MULTI-X 20-28-5126 SYLVAC Hand tools "PROXIMITY" interface MULTI-X 20-28-5134 SYLVAC Height Gauge Hi_cal 150/300/450 MULTI-X 20-28-3113 SYLVAC Height Gauge Z_cal 150 MULTI-X 20-28-3113 SYLVAC Display Unit D50S MULTI-X 20-28-5058 SYLVAC Display Unit D70 S/I/H RS232 C/670 20-28-5058 SYLVAC Display Unit D80 / D80S RS232 C/U4 20-28-3113 SYLVAC Display Unit D90S RS232 C/U4 20-28-5058 SYLVAC Display Unit D100S RS232 C/U4 20-28-5058 SYLVAC Display Unit D200S RS232 C/599 20-28-5058 TAYLOR HOBSON Form measuring instrument Talyrond 130 RS232 C/567 20-28-3137 TAYLOR HOBSON Measuring software ULTRA-SPC RS232 C/567 20-28-3137 TELEMETER LCR brigde Interface model 6452 RS232 C/260 20-28-5056 TESA Wireless interface TLC-BLE x-IW1 not required TESA Hand tools "TLC" interface MULTI-X 20-28-5226 TESA Hand tools "Opto RS-232" interface MULTI-X 20-28-3103 TESA Caliper twin cal MULTI-X 20-28-5226 TESA Height gauge MICRO-HITE 100 MULTI-X 20-28-5060 TESA Height gauge MICRO-HITE 350/600/900 RS232 C/U5 20-28-5030 TESA Height gauge MICRO-HITE 350/600/900 RS232 C/U5 20-28-5030 TESA Height gauge MICRO-HITE PLUS M 350/600/900 MULTI-X 20-28-3113 TESA Height gauge MICRO-HITE 350/600/900 MULTI-X 20-28-5226 TESA Height gauge HITE 350 / 600 MULTI-X 20-28-3103 TESA Height gauge HITE 400 / 700 magna MULTI-X 20-28-5058 TESA Height gauge µHITE MULTI-X 20-28-5060 TESA Height gauge HITE plus 350 / 600 MULTI-X 20-28-3103 TESA Height gauge HITE plus D 350 / 600 MULTI-X 20-28-3103 TESA Inductive Probe Halfbridge IND-X not required TESA TESATRONIC TT 20 / TT 60 / TT80 MULTI-X 20-28-5131 TESA TESATRONIC TTD 60 RS232 C/191 20-28-5030 TESA Profile projector TESA-SCOPE 500V RS232 C/530 20-28-3137 TESA Profile projector TESA-SCOPE 500V RS232 C/530 20-28-3137 TESA Measuring system PROFILE 25 / 30 / 80 RS232 C/159 20-28-3137 TESA Measuring system TESAScan 25 / 50 / 50 Plus RS232 C/159 20-28-3137 TESA Measuring system TESAScan 80 Plus RS232 C/159 20-28-3137

Product survey 2019

Rev. 31/2019 of 37

Manufacturer Measurement device Type Interface / driver Cable TESA Measuring system Micro-Hite 3D RS232 C/615 20-28-3137 TesT Controller Model 810 RS232 C/544 20-28-5058 TEWS-ELEKTRONIK Moisture Meter AQUATRAC-3E RS232 C/688 20-28-5147 TEXTEST PICK COUNTER FX 3250 RS232 C/638 20-28-5136 THEINERT Torque tool IQWrench2 Opta RS232 C/U4 20-28-5003 THÜMLER Z3-X500 RS232 C/696 20-28-3137 TIRA Testing machine TIRAtest 2705 RS232 C/462 20-28-3137 TRIMOS Height Gauge Mini-VERTICAL TVM MULTI-X 20-28-3103 TRIMOS Height Gauge ALTIA / ALTIA Premium 350/600 MULTI-X 20-28-3113 TRIMOS Height Gauge V / V+ MULTI-X 20-28-5058 TRIMOS Height Gauge V3/V4/V5/V6/V7/V9 RS232 C/U4 20-28-5058 TRIMOS Height Gauge VECTRA Touch 300/600/900 RS232 C/U4 20-28-3137 TRIMOS Height Gauge MESTRA Touch 300/600/1000 RS232 C/U4 20-28-3137 ULTRAKUST Porosity tester Ultrapor Typ 5665 RS232 C/435 20-28-5081 UTS TESTSYSTEME Measuring software Phoenix RS232 C/340 20-28-3137 VERSATILE Pop Tear Gauge RS232 C/217 20-28-5031 VICI Measuring software RS232 C/621 20-28-3137 VISION ENGINEERING Measuring software QC-5000 RS232 C/572 20-28-3137 VISION ENGINEERING Measuring software Dynascope RS232 C/647 20-28-3137 VÖGTLIN Flow tester red-y smart series RS232 C/487 20-28-5206 WALTER Torque tool CDWT/NDWT RS232 C/U4 20-28-5087 WAYNE KERR Analyzer 6430A / 6440A RS232 C/485 20-28-5201 WEGU Testing machine RS232 C/264 20-28-3137 WEIDMUELLER Signal converter WTS4 THERMO ANALOG 8/x 20-28-3345 WENGLOR Laser position transducer 05 MGVL-P24 ANALOG 8/10 20-28-3327 WENZEL Measuring software Metromex 3.31 RS232 C/U4 20-28-3137 WENZEL Measuring software Metrosoft CM 3.70 SP2 RS232 C/U4 20-28-3137 WERTH Measuring software WinWerth V.7.XX RS232 C/333 20-28-3137 DR. WIESNER Leak tester INTEGRA RS232 C/555 20-28-3137 WIKA Pressure transmitter Type D-10 / D-11 RS232 C/407 20-28-5104 WILHELM Force gauge PCU 500 RS232 C/466 20-28-3137 WOLF Thickness gauge Rapidometer RMP 30 b RS232 C/699 20-28-3137 WOLPERT WILSON Rockwell Hardness Tester 600MRD RS232 C/U4 20-28-5105 WTW Multi-parameter portable meter pH/Cond 3320 RS232 C/690 20-28-3137 YOKOGAWA Multimeter 7551 02 / 7552 02 RS232 C/88 20-28-3133 ZEISS Measuring software Calypso V 6.2.04 RS232 C/642 20-28-3137 ZEISS Multisensor Measuring Machine O-INSPECT RS232 C/642 20-28-3137 ZEISS Roughness gauge Handysurf E-35A RS232 C/578 20-28-5057 ZEISS Roughness gauge SURFCOM 130/480A RS232 C/196 20-28-5180 ZES ZIMMER Power Analyzer LMG 90 RS232 C/677 20-28-5117 ZUMBACH Controller USYS 1000 RS232 C/327 20-28-5019 ZUMBACH Dual-Axis Measuring Head ODAC 14XY-EN-RS RS232 C/668 20-28-5147 ZUMBACH Data acquisition system CI 1J/EN-RS RS232 C/213 20-28-5147 ZUMBACH Measuring software Wiremaster RS232 C/213 20-28-5019 ZWICK / ROELL Hardness Tester ZHR 4150 RS232 C/U4 20-28-5011 ZWICK / ROELL Hardness Tester ZHU250 RS232 C/669 20-28-3137 ZWICK / ROELL Measuring software testXpert (V9.0 …) RS232 C/370 20-28-3137 ZWICK / ROELL Measuring software testXpert II RS232 C/370 20-28-3137 ZWICK / ROELL Measuring software testXpert III RS232 C/370 20-28-3137 ZYGO Laser micrometer Model 1200 RS232 C/73 20-28-5069

Automatische Erstellung der Preisliste · Our simple but powerful protocol is supported by all...

Documents

Transcript of Automatische Erstellung der Preisliste · Our simple but powerful protocol is supported by all...