AUTHOR’S GUIDELINE FOR PREPARATION OF … · Web viewPDF format. in high quality print and also...
3
NORDIC STEEL 2019 The 14th Nordic Steel Construction Conference, September 18–20, 2019, Copenhagen, Denmark Paper Template for Nordic Steel 2019 in Copenhagen [Main Title] Manuscript Preparation Using Microsoft Word [optional: Sub title] Michael Joachim Andreassen* ,a , Jeppe Jönsson a , Jørn Nielsen b a Technical University of Denmark, Dept. Civil Engineering, Denmark [email protected], [email protected] b Danish Steel Institute, Denmark [email protected] ABSTRACT Please provide a summary of your paper in form of an Abstract. The Abstract should not be longer than 300 words. Please write your paper directly in this template, which has the format as described below. Full paper must be prepared using this template and submitted in PDF format in high quality print and also including the original word file. Submissions may not exceed 20 Megabyte. Please do not insert page numbers and do not secure the PDF file. Please also note: you must embed the fonts into the word file: please follow this Microsoft manual for more details: https://support.microsoft.com/en-us/kb/290952 In the manuscript-head: please make sure you mark the designated corresponding author with an asterisk * (e.g. see “Michael Joachim Andreassen”). Keywords: keyword 1, keyword 2, keyword 3, keyword 4 [provide at least 3 keywords, 4 at maximum] 1 INTRODUCTION 1.1 Paper, authors and affiliation Title format: 14pt Times New Roman, bold, capital letters; center adjusted. For a title longer than one line it is preferred that it is split into a single-line title and a subtitle. Subtitle is 12pt Times New Roman. Please use the pre-set style format Title 1 and Subtitle 1. Authors are listed with full names, followed by the referred organization list. Use the corresponding templates. 1.2 Paper size, margins and numbering Please use page size A4. The text should fit exactly into the type area. For A4 size paper the margin settings are: Top: 20 mm; Bottom: 15 mm; Inside: 25 mm; Outside: 15 mm. Table 1 summarizes the margins applied. Please do not insert page numbers. 1.3 Sections The paper sections starts with the ABSTRACT, followed by the consecutively numbered main sections. Include a list of numbered references at the end of the manuscript (use the template format). Summary and Acknowledgments are optional. 1.4 Paper length and language Paper length is limited to 6 pages of size A4. Language of the paper shall be English. Please proofread your paper.
Transcript of AUTHOR’S GUIDELINE FOR PREPARATION OF … · Web viewPDF format. in high quality print and also...
NORDIC STEEL 2019The 14th Nordic Steel Construction Conference,September 18–20, 2019, Copenhagen, Denmark
Paper Template for Nordic Steel 2019 in Copenhagen [Main Title]Manuscript Preparation Using Microsoft Word [optional: Sub title]
Michael Joachim Andreassen*,a, Jeppe Jönssona, Jørn Nielsenb
aTechnical University of Denmark, Dept. Civil Engineering, Denmark [email protected], [email protected]
b Danish Steel Institute, Denmark [email protected]
ABSTRACTPlease provide a summary of your paper in form of an Abstract. The Abstract should not be longer than 300 words. Please write your paper directly in this template, which has the format as described below.Full paper must be prepared using this template and submitted in PDF format in high quality print and also including the original word file. Submissions may not exceed 20 Megabyte. Please do not insert page numbers and do not secure the PDF file. Please also note: you must embed the fonts into the word file: please follow this Microsoft manual for more details: https://support.microsoft.com/en-us/kb/290952In the manuscript-head: please make sure you mark the designated corresponding author with an asterisk * (e.g. see “Michael Joachim Andreassen”).
Keywords: keyword 1, keyword 2, keyword 3, keyword 4 [provide at least 3 keywords, 4 at maximum]
1 INTRODUCTION1.1 Paper, authors and affiliationTitle format: 14pt Times New Roman, bold, capital letters; center adjusted. For a title longer than one line it is preferred that it is split into a single-line title and a subtitle. Subtitle is 12pt Times New Roman.Please use the pre-set style format Title 1 and Subtitle 1.Authors are listed with full names, followed by the referred organization list. Use the corresponding templates.
1.2 Paper size, margins and numberingPlease use page size A4. The text should fit exactly into the type area. For A4 size paper the margin settings are: Top: 20 mm; Bottom: 15 mm; Inside: 25 mm; Outside: 15 mm. Table 1 summarizes the margins applied. Please do not insert page numbers.
1.3 SectionsThe paper sections starts with the ABSTRACT, followed by the consecutively numbered main sections. Include a list of numbered references at the end of the manuscript (use the template format). Summary and Acknowledgments are optional.
1.4 Paper length and languagePaper length is limited to 6 pages of size A4.Language of the paper shall be English. Please proofread your paper.
1.5 Submission deadlinePlease submit your full paper before 21th January 2019 via the online submission system.We would like to emphasize that abstract acceptance does not mean automatic acceptance of your paper. The extended papers are peer reviewed, and thus the final decision for paper acceptance will be based on this final paper review, after the final paper submission.
2 SECTION HEADINGS AND TEXT STYLE2.1 Heading 1Format of section headings: bold capitals Times New Roman 12 pt. Line spacing before and after a heading is 18 pt and 6 pt, respectively. Please use the preset style Heading 1. Use consecutive numbering of the sections; the preset style comes with automatic numbering. Introduction and References are not required to number (you may use the separate preset formats Introduction heading and Reference heading).
2.2 Heading 2Secondary headings are typed in initial capitals. Please limit the depth of headings to major and secondary headings.
2.3 Normal text style and listThe normal text is typed in Times New Roman 12 pt, justified with single line spacing.For numbered or bulleted list please use the provided style templates 1. List numbered List bullet.
3 FIGURES, TABLES AND EQUATIONS3.1 TablesTables prepared in basic word format are preferred. Tables must be referred in the text in the format as Table 1. The smallest font size in the table shall not be smaller than 10 pt.
Table 1. Margins of the page size A4 [mm]
top bottom inside outside
20 15 25 15
3.2 EquationsUse the equation editor of Word or preferably MathType with the standard settings (12pt italic Times New Roman). Equations shall be numbered. An example is given in Eq. (1).
σ=MEd
I y⋅zmax=235
Nmm2
(1)
where MEd is the design bending moment, is the acting axial stress, etc.
3.3 Figures, diagrams, illustrationsFigures, diagrams, illustrations should have a resolution of 600 dpi. Reference to the figures shall be given in the text. Two-column figure arrangement as shown in Fig. 1 is allowed: use a table format without borders. The smallest font size in the figures shall not be smaller than 10 pt.
© Ernst & Sohn Verlag für Architektur und technische Wissenschaften GmbH & Co. KG, Berlin ∙ ce/papers (2019)
a) b)
Fig. 1. a) Drawing; b) Colour photograph
4 PRESET FORMATSUse the Formats as shown in this template to get a consistent layout of the conference proceeding. See the Styles toolbox in the Home tab of your word program.
5 SUMMARY AND ACKNOWLEDGMENTSummary and acknowledgments are optional. Numbered reference list shall be given as follows.
REFERENCESReferences in the text should appear (1), (2), (3), etc. Use a comma (not an en dash) between two consecutive reference citations, e.g. (1, 2). Use an un-spaced dash to indicate a numerical range within reference citation, e.g. (4–6). References should appear in numerical order in the text and listed numerically in the reference list at the end of the paper. Thus the order of the list matches the order of appearance of references in the text. Please use Microsoft Word’s built in Reference Manager to enter your references here and chose the format ISO 690 Numbered Reference.
1. Andreassen, Michael Joachim and Jönsson, Jeppe. Joint and column behaviour of slotted cold formed steel studs. ‐ Steel Construction. 2015, 3, pp. 155-161.2. Block failure in connections-including effets of eccentric loads. Jönsson, Jeppe. s.l. : University of Naples Federico II, 2014. 7th European conference on steel and composite structures. p. 301. .3. Whitmore, Richard E. Whitmore, Richard E. Experimental investigation of stresses in gusset plates. Knoxville : University of Tennessee, 1952.
© Ernst & Sohn Verlag für Architektur und technische Wissenschaften GmbH & Co. KG, Berlin ∙ ce/papers (2019)
