Australia : Italia : www ...€¦ · !18 17 2 0 1 6 1 9 6 Accessory list for this page. Install the...
Transcript of Australia : Italia : www ...€¦ · !18 17 2 0 1 6 1 9 6 Accessory list for this page. Install the...
SAFETY PRECAUTIONSThis radio control model is not a toy!
lFirst-time builders should seek advice from people having building experience in order to assemble the model correctly and to produce its performance to full extent.
,lAssemble this kit only in places out of children s reach!lTake enough safety precautions prior to operating this model.
, You are responsible for this model s assembly and safe operation!lAlways keep this instruction manual ready at hand for quick reference,even after completing the assembly. lCould cause serious injury or even death
SPECIFICATION
LA-7LA-7
ALMOST - READY - TO - FLYALMOST - READY - TO - FLYBefore commencing assembly,please read these instructions thoroughly.
Thank you for choosing CYmodelGlobal : www.cymodel.com
Australia : www.austars-model.com
Italia : www.biellaexpress.com
Instruction Manual
Item Nr: CY8024B
Wing Span.......2450mm/96.5in2
Wing Area........92dm /1430sq.inTotal Length.....2095mm/82.5inEngine:80-100cc gas engineRadio:6 channels,8-9 servos
REQUIRED FOR OPERATION (Purchase separately) REQUIRED FOR OPERATION (Purchase separately) REQUIRED FOR OPERATION (Purchase separately) REQUIRED FOR OPERATION (Purchase separately)
TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)TOOLS REQUIRED ( Purchase separately)
BEFORE YOU BEGINBEFORE YOU BEGINBEFORE YOU BEGINBEFORE YOU BEGIN
Sharp Hobby Knife Phillips Screw Driver Awl
Needle Nose Pliers Wire Cutters Scissors
Read through the manual before you begin ,so you will have an overall idea of what to do.
Check all parts .if you find any defective or missing parts .contact your local dealer.
Symbols used throughout this instruction manual,comprise.
111
222
333
.
.
Warning!!Do not overlook this symbol.
A minimum 6channel radio for airplanes (with 9servos).And dry batteries.
CAUTION: Only use a minimum 6channel radio for airplanes! (No other radio may be used!) !
12 AA-size Batteries
A minimum 6 channel transmitter for airplanes.
For handing the radio properly.refer to its instruction manual.
Engine and Muffler
Purchase a propeller thatwill match your engine
Silicone Tube Fuel Filter
required for engine starting Glow engine fuel only.
WARNING: Normal gasoline cannot
be used with glow engines.
!
Fuel Pump Plug Wrench
Glue
Instant glue Epoxy Glue
Other equipment for enhancing airplane operation & perormance
12V Battery (for starter)Engine Starter
BBBB
22
Cut off shaded portion.
Ensure smooth non-binding movement while assembling.
Must be purchased
separately!
Pay close attention
here!
Drill holes with the specified
Diameter(here:2mm)
Assemble left and right Sides the same way.
Apply instant glue
(CA glue,super glue).
Apply epoxy glue.
Cut off excess.
502
C.AC.A
LLRR
A B
2mm2mm
99
44
11
77
66
55
88Model Airplane engine:80-100cc gas engine
receiver
22 Battery (need 2)
33 Servo(need 9 servos )
remote control
Switch (need 2)
AA
Muffler
Muffler
! 3
2
1
5
4
33
Install the aileron and flap Install the servo of aileron
Install the servo
Aileron
Flap
Install the aileron and flap
Bottom view
Install the servo of flap
Accessory list for this page.
LLRR
LLRR
Securely glue together. If coming off during flights,you'lllose control of your airplane which leads to accidents!
Warning!Warning!
LLRR
FlapAileron
A B
A B
A B
A B
Make sure hinges aremounted in the same line
LLRR
Flap Aileron
Tailing edge
Aileron
4mm
LLRR
LLRR
Servo line
A B
Rod adjuster
2.5X85mm rod
HORN
3X16 Screw
Rod adjuster
2
4
2
4
2
43mm Lock nut
2.6X12mm Tp Screw8
LLRR
Servo line
A B
Rod adjuster
2.5X85mm rod
HORN
3X16 Screw
Rod adjuster
2
4
2
4
2
43mm Lock nut
2.6X12mm Tp Screw8
Hinge
Hinge
- - - - - - - - 6
- - - - - - - - 8
Hinge
Hinge
Rod adjuster
2.5X85mm rod
HORN
3X16 Screw
Rod adjuster
4
8
4
8
4
83mm Lock nut
8
6
2.6X12mm Tp Screw16
! 8
7
6
10
9
44
Accessory list for this page.
Install the elevator
LLRR
Securely glue together. If coming off during flights,you'lllose control of your airplane which leads to accidents!
Warning!Warning!
LLRR
Bottom view
Install the elevator
make sure hinges aremounted in the same line
A B
Hinge - - - - - - - - 8
Install the elevator servos
Install the elevator servos
LLRR
LLRR
LLRR
Install the rudder
make sure hinges aremounted in the same line
Hinge - - - - - - - 3
A B
LLRR
A B
Rod adjuster
2.5X85mm rod
HORN
3X16 Screw
Rod adjuster
2
4
2
4
2
43mm Lock nut
Rod adjuster
2.5X85mm rod
HORN
3X16 Screw
Rod adjuster
2
4
2
4
2
43mm Lock nut
Hinge12
! 13
12 15
1414
55
11
Accessory list for this page.
Install the rudder
Install the rudder
Install the tail wheel
Install the servos of rudder&tail wheel
Install the tail wheel
Securely glue together. If coming off during flights,you'lllose control of your airplane which leads to accidents!
Warning!Warning!
Tailing edge
Rudder
4mm
A B
3.2mm Collar
3.2mm Nylon Collar
3X3mm Screw
6X9 screw
M3X20 Tp screw
3.2mm Rocker
6mm nut1
1
3
1
3
1
2
A B
Aluminium tube
Rod
Steel wire
Rod adjuster
HORN
3X16 Screw
2
2
2
23mm Lock nut
2
2
2
Spring2
Aluminium tube
Rod
Rod adjuster
3X16 Screw
2
2
23mm Lock nut
2
2
3.2mm Collar
3.2mm Nylon Collar
3X3mm Screw
6X9 screw
M3X20 Tp screw
3.2mm Rocker
6mm nut1
1
3
1
3
1
2
Aluminium tube
Rod
Steel wire
Rod adjuster
HORN
3X16 Screw
2
2
4
43mm Lock nut
2
4
4
Rod adjuster2
Spring2
! 18
17 20
1916
66
Accessory list for this page.
Install the main landing gear
Install the main landing gear
LLRR
Pleas notice the inner diameter for each side of the pressure reduction inlet.
Please insure the sealing of the retract system before flight .
Install the main landing gear
Install the main landing gear
RetainerRod adjuster
2X8mm screw
- - - - - 1
- - - - - 1
- - - - - 1
Rod (1.8X80mm)
- - - - - 1
900 Air line
- - - - - 2
LLRR
Air tank
Switch
Air inlet
3-waypressure inlet
3-waypressure inlet
3-waypressure inlet
Quick release connector Quick release connector
Strut Strut
Horizontal (Put the servo into the fuselage)
LLRR
502
C.AC.A
After glue the PVC cover,cut off its excess part.
LLRR
3X20mm Tp screw
- - - - - 8
Ply wood- - - - - - - - - - - -2
3X5mm screw- - - - - - - - - - - -4
3X20mm Tp screw
- - - - - 8
8mm nylon Nut
- - - - - 4
Retainer
Rod adjuster
2X8mm screw
- - - - - 1
- - - - - 1
- - - - - 1
Rod (1.8X80mm) - - - - - 1
900 Air line
- - - - - 2
Ply wood
3X5mm screw
- - - - - 4
- - - - - 2
4X25mm screw
4mm Washer
- - - - - - - - 2
- - - - 2
4mm4mm
4X25mm screw
4mm Washer
- - - - - - - - 2
- - - - 2
4mm Lock nut
- - - - - 2
4mm Lock nut
- - - - - 2
3mm3mm
! 23
25
77
21 24
22
Accessory list for this page.
Main wing&Horizontal/Vertical tail
Securely glue together ,if coming off during flights.You lose control of your airplane which leads to accidents!
A AB BC C
Installing the engine mount
Main wing (Put the servo line into the fuselage)
8mm nylon Nut
- - - - - 4
Installing the engine (80-100cc)
AA
BB
CC
3X16mm screw
- - - - -123mm Lock nut
- - - - - 12
3mm Washer
- - - - - 24
Aluminium plank
- - - - - 2
3mm3mm
A B
275mm
Fuel tankFuel tank
Throttle Throttle
4X25mm screw
4mm Washer
- - - - - - - - 2
- - - - 2
3X16mm screw
- - - - -123mm Lock nut
- - - - - 12
3mm Washer
- - - - - 24
Aluminium plank
- - - - - 2
8mm nylon Nut
- - - - - 4
After confirming the position(see front of fuel tank).Insert and tighten the screw.
Fuel supply line
Fuel pipe
Air pressure line
Assembly of the full tank
! 28
27 30
29
88
26
Accessory list for this page.
Radio Equipment
Install the thr cowling
Receiver ReceiverBatteryBatteryBattery/IgnitionBattery/Ignition
Install the canopy
SpinnerSpinner
PropellerPropeller
3mm Washer
- - - - - 2
3X30mm screw
- - - - - 2
3mm rubber band
- - - - 2
2.3X10mm Tp screw
- - - - -8
1.8X200mm Rod
- - - - - - 1
Linkage Stopper
2mm Nut
- - - - 1
- - - - 1
3X3mm Screw
- - - - - - 1
Install the throttle servo
Cut away the surplus pats of canopy,care fully along the shaded line.
3mm Washer
- - - - - 5
3X14mm screw
- - - - - 5
3mm rubber band
- - - - 51.8X200mm Rod
- - - - - - 1
Linkage Stopper
2mm Nut
- - - - 1
- - - - 1
3X3mm Screw
- - - - - - 1
3mm Washer
- - - - - 7
3X30mm screw
- - - - - 2
3mm rubber band
- - - - 7
2.3X10mm Tp screw
- - - - -8
3X14mm screw
- - - - - 5
33
32 34
Side view
ELEVATOR
Adjust the travel of each control surface to the values in the diagrams.These values fit general flight capabilities.Readjust according to your needs and flight level.
Top view
31
AILERON
Adjustment.
Top view
Adjust the travel of each control surface to the values in the diagrams.These values fit general flight capabilities.Readjust according to your needs and flight level.
99
Adjustment.
Never fly before checking the Cg s required position.
In order to obtain the CG specified ,reposition the receiver and battery.
NEVER fly the model without well balancing.Warning!!
CG
Side view
Rudder
Adjust the travel of each control surface to the values in the diagrams.These values fit general flight capabilities.Readjust according to your needs and flight level.
Top view
190-195mm190-195mm
Adjustment
Side view
Adjustment.
45
45
45
45
45
Flap
45
45