AUGER DREDGERS
21
AUGER DREDGERS ECO 200 ECO 250 CUTTER SUCTION DREDGERS ECO 250 ECO 300 CUTTER SUCTION DREDGER CSD 400 CSD 450
Transcript of AUGER DREDGERS
AUGER DREDGERS ECO 200 ECO 250
CUTTER SUCTION DREDGERS ECO 250 ECO 300
CUTTER SUCTION DREDGER CSD 400 CSD 450
Dredge Applications
Our dredgers are designed to excavate and transport soil materials of different densities
from fine sand and clay to gravel. In addition to this, we offer to customize dredgers for
your specific project needs. Therefore, we can offer dredgers suitable for a variety of
applications
RIVER DREDGING & DEEPENING
SETTLING POND DREDGING
River dredging is necessary to keep waterways open for inland transport & to prevent flooding.
We offer dredgers for cleaning, desilting and desludging a wide range of industrial settling ponds, holding ponds and lagoons.
RESERVOIR, LAKE & DAM DREDGING
WATER INTAKE DREDGING
Reservoir, lake and dam dredging should be done regularly in order to restore them to their full capacities.
Regular maintenance dredging in the form of water intake cleaning is needed to keep the water basins clean and the capacity of the industrial plant at its maximum.
MINE TAILING REMOVAL & DREDGING
ENVIRONMENTAL DREDGING
Our dredgers can be used for mine tailing removal to clean up or dredge ponds. Following this, the tailings can be disposed of or further processed for valuables.
Environmental dredging requires precise, low turbidity dredging. We offer dredgers, which avoid dispersion of pollutants & have minimal impact on the environment.
CANAL & CHANNEL DREDGING
MARINA & HARBOR DREDGING
Regular canal & channel maintenance dredging is vital to ensure safe and efficient navigation, irrigation, commerce and businesses running smoothly.
Regular maintenance dredging is required to make sure marinas and harbors provide safe navigation and access at all times, and to avoid disruption of waterway traffic.
AUGER DREDGER ECO 200
MAIN PARTICULARS
Type Auger Suction Dredger
Pontoons Foldable pontoons
Transport Inside 40 ft high cube open top container
Suction Pipe 200 mm 8 inch
Discharge pipe 200 mm 8 inch
Suitable for dredging Clay, Medium Sand and Coarse sand
Dredging depth 8 m 26 ft
POWER UNIT
Diesel engine Perkins 1100
Engine type Industrial power unit
Engine tier EPA tier 3 emissions (higher optional)
Engine power 168 kW 225 hp
Cooling Radiator cooling
Engine speed 1800-2200 rpm
MAIN DIMENSIONS
Length overall 11.80 m 38.7 ft
Number of pontoons 4 (2x fixed)
Length over pontoons 10.14 m 33.3 ft
Width overall 3.37 m 11.0 ft
Width during transport 2.30 m 7.5 ft
Height overall at operation 3.16 m 10.4 ft
Height of pontoon 1.00 m 3.3 ft
Design draught 0.60 m 2.0 ft
DREDGE PUMP
Type DREDGE YARD DY200S
Configuration Single stage centrifugal pump
Position Submerged mounted on the ladder
Suction diameter 200 mm 8 inch
Discharge diameter 200 mm 8 inch
Impeller number of vanes 3
Dredge pump motor power 140 kW 188 hp
Dredge pump 600-1300 rpm
Wear material GX260 White Iron - high wear resistant
Drive Direct hydraulic drive
Bearing block Two spherical roller bearings
Shaft Seal Mechanical Shaft Seal
DREDGE AUGER HEAD
Type DY210-C Multipurposed
Configuration Helical auger head with conical entry
Auger width 2.10 m 6.9 ft
Auger motor power 15 kW 20 hp
Auger motor speed 0-60 rpm
Cutting system Cutting knives (optional)
DREDGING WINCH
Type of winch Traverse winch
Movement Forward and Backward
Number of winches 1 unit
Wire pull 20 kN 4496 lbs
Hauling speed 0-20 m/min 0-65 ft/min
Wire diameter 13 mm 0.5 inch
Drive Hydraulic motor
LADDER HOISTING WINCH
Type of winch Drum winch
Number of winches 1 unit
Wire pull 35 kN 7868 lbs
Hauling speed 0-20 m/min 65 ft/min
Wire diameter 13 mm 0.5 inch
Drive Hydraulic motor
PROPULSION (Optional)
Purpose Simple maneuvering in sheltered waters
Type Two fixed propellers
Total power 44 kW 59 hp
Trust Force 6.9 kN 1552 lbs
Direction of Vessel Forward, reverse, left and right
FUEL
Type Diesel fuel
Tank capacity 1000 liters 264 gallon
DREDGER OPERATING CABIN
Total area 1.96 m2 21 sq-ft
Cooling Ventilation fan ( a/c optional )
Lights 1x interior light and 2x flood light
Additional Screen wipers
Instrumentation Dredging depth indication
Production in Water
Production Insitu
AUGER DREDGER ECO 250
MAIN PARTICULARS
Type Auger Suction Dredger
Pontoons Foldable pontoons
Transport Assembled on flat track container
Suction Pipe 300 mm 12 inch
Discharge pipe 250 mm 10 inch
Suitable for dredging Clay, Medium Sand and Coarse sand
Dredging depth 8 m 26 ft
POWER UNIT
Diesel engine CAT C9
Engine type Industrial power unit
Engine tier EPA tier 3 emissions (higher optional)
Engine power 224 kW 300 hp
Cooling Radiator cooling
Engine speed 1800-2100 rpm
MAIN DIMENSIONS
Length overall 11.80 m 38.7 ft
Number of pontoons 4 (2x fixed)
Length over pontoons 10.90 m 35.8 ft
Width overall 4.10 m 13.5 ft
Width during transport 3.00 m 9.9 ft
Height overall at operation 3.30 m 10.8 ft
Height of pontoon 1.00 m 3.3 ft
Design draught 0.65 m 2.1 ft
DREDGE PUMP
Type DREDGE YARD DY250
Configuration Single stage centrifugal pump
Position Submerged mounted on the ladder
Discharge diameter 250 mm 10 inch
Impeller number of vanes 3
Dredge pump motor power 160 kW 215 hp
Dredge pump 825-975 rpm
Wear material GX260 White Iron - high wear resistant
Drive Direct hydraulic drive
Bearing block Two spherical roller bearings + one spherical roller thrust bearing
Shaft Seal Mechanical Shaft Seal
DREDGE AUGER HEAD
Type DY300-C Multipurposed
Configuration Helical auger head with conical entry
Auger width 2.92 m 9.6 ft
Auger motor power 30 kW 40 hp
Auger motor speed 0-60 rpm
Cutting system Cutting knives (optional)
DREDGING WINCH
Type of winch Traverse winch
Movement Forward and Backward
Number of winches 1 unit
Wire pull 20 kN 4496 lbs
Hauling speed 0-20 m/min 0-65 ft/min
Wire diameter 13 mm 0.5 inch
Drive Hydraulic motor
LADDER HOISTING WINCH
Type of winch Drum winch
Number of winches 1 unit
Wire pull 35 kN 7868 lbs
Hauling speed 0-20 m/min 65 ft/min
Wire diameter 13 mm 0.5 inch
Drive Hydraulic motor
PROPULSION (Optional)
Purpose Simple maneuvering in sheltered waters
Type Two fixed propellers
Total power 44 kW 59 hp
Trust Force 6.9 kN 1552 lbs
Direction of Vessel Forward, reverse, left and right
FUEL
Type Diesel fuel
Tank capacity 1000 liters 264 gallon
DREDGER OPERATING CABIN
Total area 1.96 m2 21 sq-ft
Cooling Ventilation fan ( a/c optional )
Lights 1x interior light and 2x flood light
Additional Screen wipers
Instrumentation Dredging depth indication
Production in Water
Production Insitu
MAIN PARTICULARS
Type of dredger Cutter Suction Dredger
Pontoons Three dismountable pontoons
Transport Inside one high cube container and three standard containers
Suction Pipe 250 mm 10 inch
Discharge pipe 250 mm 10 inch
Suitable for dredging Clay, Medium Sand and Coarse sand
Dredging depth 8 m 26 ft
POWER UNIT
Diesel engine CAT C11
Engine type Industrial power unit
Engine tier EPA tier 3 emissions (higher optional)
Engine power 261 kW 350 hp
Cooling Radiator cooling
Engine speed 1800-2100 rpm
MAIN DIMENSIONS
Length overall 19.90 m 65.3 ft
Number of pontoons 3
Length over pontoons 11.50 m 37.8 ft
Width overall 5.33 m 17.5 ft
Width during transport 5.33 m 17.5 ft
Height overall at operation 3.95 m 13.0 ft
Height of pontoon 1.25 m 4.1 ft
Design draught 0.70 m 2.3 ft
CUTTER DREDGER ECO 250
DREDGE PUMP
Type DREDGE YARD DY250
Configuration Single stage centrifugal pump
Position Submerged mounted on the ladder
Discharge diameter 250 mm 10 inch
Discharge diameter 250 mm 10 inch
Impeller number of vanes 3
Dredge pump motor power 192 kW 257 hp
Dredge pump 800-1000 rpm
Wear material GX260 White Iron - high wear resistant
Drive Direct hydraulic drive
Bearing block Two spherical roller bearings & one spherical roller thrust bearing
Shaft seal Mechanical Shaft Seal
DREDGE CUTTER HEAD
Type DY740-C Multipurposed
Configuration Crown type interchangeable teeth
Cutter diameter 0.74 m 2.4 ft
Cutter motor power 35 kW 47 hp
Cutter motor speed 0-40 rpm
Cutting system 3 type of replaceable teeth
Narrow teeth, pick points and chisel
DREDGING WINCH
Type of winch Drum winch
Movement Swing left and right 35 degrees
Number of winches 2 unit
Wire pull 40 kN 8993 lbs
Hauling speed 0-20 m/min 0-65 ft/min
Wire diameter 13 mm 0.5 inch
Drive Hydraulic motor
LADDER HOISTING WINCH
Type of winch Drum winch
Number of winches 1 unit
Wire pull 35 kN 7868 lbs
Hauling speed 0-20 m/min 65 ft/min
Wire diameter 13 mm 0.5 inch
Drive Hydraulic motor
PROPULSION (Optional)
Purpose Simple maneuvering in sheltered waters
Type Two fixed propellers
Total power 44 kW 59 hp
Trust Force 6.9 kN 1552 lbs
Direction of Vessel Forward, reverse, left and right
FUEL
Type Diesel fuel
Tank capacity 3500 liters 925 gallon
DREDGER OPERATING CABIN
Total area 1.96 m2 21 sq-ft
Cooling Ventilation fan ( a/c optional )
Lights 1x interior light and 2x flood light
Additional Screen wipers
Instrumentation Dredging depth indication
Production in Water
Production Insitu
MAIN PARTICULARS
Type of dredger Cutter Suction Dredger
Pontoons Three dismountable pontoons
Transport Inside one high cube container and three standard containers
Suction Pipe 300 mm 12 inch
Discharge pipe 300 mm 12 inch
Suitable for dredging Clay, Medium Sand and Coarse sand
Dredging depth 8 m 26 ft
POWER UNIT
Diesel engine CAT C13
Engine type Industrial power unit
Engine tier EPA tier 3 emissions (higher optional)
Engine power 310 kW 415 hp
Cooling Radiator cooling
Engine speed 1800-2100 rpm
MAIN DIMENSIONS
Length overall 19.90 m 65.3 ft
Number of pontoons 3
Length over pontoons 11.50 m 37.8 ft
Width overall 5.33 m 17.5 ft
Width during transport 5.33 m 17.5 ft
Height overall at operation 3.95 m 13.0 ft
Height of pontoon 1.25 m 4.1 ft
Design draught 0.70 m 2.3 ft
CUTTER DREDGER ECO 300
DREDGE PUMP
Type DREDGE YARD DY300
Configuration Single stage centrifugal pump
Position Submerged mounted on the ladder
Discharge diameter 300 mm 12 inch
Discharge diameter 300 mm 12 inch
Impeller number of vanes 3
Dredge pump motor power 231 kW 310 hp
Dredge pump 650-800 rpm
Wear material GX260 White Iron - high wear resistant
Drive Direct hydraulic drive
Bearing block Two spherical roller bearings & one spherical roller thrust bearing
Shaft seal Mechanical Shaft Seal
DREDGE CUTTER HEAD
Type DY860-C Multipurposed
Configuration Crown type interchangeable teeth
Cutter diameter 0.86 m 2.8 ft
Cutter motor power 40 kW 54 hp
Cutter motor speed 0-40 rpm
Cutting system 3 type of replaceable teeth
Narrow teeth, pick points and chisel
DREDGING WINCH
Type of winch Drum winch
Movement Swing left and right 35 degrees
Number of winches 2 unit
Wire pull 40 kN 8993 lbs
Hauling speed 0-20 m/min 0-65 ft/min
Wire diameter 13 mm 0.5 inch
Drive Hydraulic motor
LADDER HOISTING WINCH
Type of winch Drum winch
Number of winches 1 unit
Wire pull 35 kN 7868 lbs
Hauling speed 0-20 m/min 65 ft/min
Wire diameter 13 mm 0.5 inch
Drive Hydraulic motor
PROPULSION (Optional)
Purpose Simple maneuvering in sheltered waters
Type Two fixed propellers
Total power 44 kW 59 hp
Trust Force 6.9 kN 1552 lbs
Direction of Vessel Forward, reverse, left and right
FUEL
Type Diesel fuel
Tank capacity 3500 liters 925 gallon
DREDGER OPERATING CABIN
Total area 1.96 m2 21 sq-ft
Cooling Ventilation fan ( a/c optional )
Lights 1x interior light and 2x flood light
Additional Screen wipers
Instrumentation Dredging depth indication
Production in Water
Production Insitu
MAIN PARTICULARS
Type of dredger Cutter Suction Dredger
Pontoons Three dismountable pontoons
Transport Dismountable on flat tracks
Suction Pipe 400 mm 16 inch
Discharge pipe 400 mm 16 inch
Suitable for dredging Clay, Medium Sand and Coarse sand
Dredging depth 10 m 32.2 ft
POWER UNIT
Diesel engine CAT C18
Engine type Marine Engine
Engine tier EPA tier 3 emissions (higher optional)
Engine power 483 kW 648 hp
Cooling Water cooling
Engine speed 1800 rpm
MAIN DIMENSIONS
Length overall 24.0 m 78.8 ft
Number of pontoons 3
Length over pontoons 14.0 m 46.0 ft
Width overall 5.7 m 18.7 ft
Depth main pontoon 2.48 m 8.1 ft
Depth side pontoons 1.47 m 4.8 ft
Design draught 1.1 m 3.6 ft
CUTTER DREDGER CSD 400
DREDGE PUMP
Type DREDGE YARD DY400
Configuration Single stage centrifugal pump
Position Inside main pontoon
Suction diameter 400 mm 16 inch
Discharge diameter 400 mm 16 inch
Impeller number of vanes 3
Dredge pump power 380 kW 510 hp
Dredge pump 400-600 rpm
Wear material High wear resistant
Drive Direct drive through a single stage gearbox
Gearbox Single stage vertical offset with integrated clutch
Shaft Seal Stuffing box
DREDGE CUTTER HEAD
Type DY-1000C Multipurposed
Configuration Crown type interchangeable teeth
Cutter ring diameter 1.0 m 3.3 ft
Cutter motor power 57 kW 76 hp
Cutter motor speed 0-35 rpm
Drive Hydraulic motor
Cutting system 3 type of replaceable teeth
Narrow teeth, pick points and chisel
DREDGING WINCH
Type of winch Drum winch
Movement Swing left and right 35 degrees
Number of winches 2 unit
Wire pull 40 kN 8,992 lbs
Hauling speed 0-15 m/min 0-49 ft/min
Wire diameter 16 mm 10/16 inch
Drive Hydraulic motor
Range at min depth 25.0 m 82.0 ft
Range at max depth 20.5 m 67.3 ft
LADDER HOISTING WINCH
Type of winch Drum winch
Number of winches 1 unit
Wire pull 40 kN 8,992 lbs
Hauling speed 0-15 m/min 49 ft/min
Wire diameter 16 mm 10/16 inch
Drive Hydraulic motor
DREDGE SPUDS
Spud Length 13.0 m 42.7 ft
Spud diameter 368 mm 14.5 inch
Spud weight 1,550 kg 3,417 lbs
Cylinder lifting force 60 kN 33,488 lbs
Spud stroke 3.0 m 9.8 ft
FUEL
Type Diesel fuel
Tank capacity 8,000 liters 2,113 gallon
DREDGE OPERATING CABIN
Total area 3.0 m2 32.3 sq-ft
Cooling Ventilation fan ( a/c optional )
Lights 1x interior light and 2x flood light
Additional Screen wipers
Instrumentation Dredging depth indication
Discharge pressure gauge
Vacuum pressure gauge
MAIN PARTICULARS
Type of dredger Cutter Suction Dredger
Pontoons Three dismountable pontoons
Transport Dismountable on flat tracks
Suction Pipe 500 mm 20 inch
Discharge pipe 450 mm 18 inch
Suitable for dredging Clay, Medium Sand and Coarse sand
Dredging depth 10 m 32.2 ft
Depth is extendable 12 m 39.4 ft
POWER UNIT
Diesel engine CAT C32
Engine type Marine Engine
Engine tier EPA tier 3 emissions (higher optional)
Engine power 895 kW 1200 hp
Cooling Water cooling
Engine speed 1800 rpm
MAIN DIMENSIONS
Length overall 26.2 m 86.0 ft
Number of pontoons 3
Length over pontoons 18.10 m 59.4 ft
Width overall 6.60 m 21.6 ft
Depth main pontoon 2.45 m 8.0 ft
Depth side pontoons 1.80 m 5.9 ft
Design draught 1.4 m 4.6 ft
CUTTER DREDGER CSD 450
DREDGE PUMP
Type DREDGE YARD DY450
Configuration Single stage centrifugal pump
Position Inside main pontoon
Suction diameter 450 mm 18 inch
Discharge diameter 400 mm 16 inch
Impeller number of vanes 3
Dredge pump power 634 kW 850 hp
Dredge pump 400-600 rpm
Wear material High wear resistant
Drive Direct drive through a single stage gearbox
Gearbox Single stage vertical offset with integrated clutch
Shaft Seal Stuffing box
DREDGE CUTTER HEAD
Type DY-1510C Multipurposed
Configuration Crown type interchangeable teeth
Cutter ring diameter 1.51 m 4.95 ft
Cutter motor power 112 kW 150 hp
Cutter motor speed 0-35 rpm
Drive Hydraulic motor
Cutting system 3 type of replaceable teeth
Narrow teeth, pick points and chisel
DREDGING WINCH
Type of winch Drum winch
Movement Swing left and right 35 degrees
Number of winches 2 unit
Wire pull 65 kN 14,612 lbs
Hauling speed 0-15 m/min 0-49 ft/min
Wire diameter 18 mm 11/16 inch
Drive Hydraulic motor
Range at min depth 29.5 m 96.8 ft
Range at max depth 24.0 m 78.7 ft
LADDER HOISTING WINCH
Type of winch Drum winch
Number of winches 1 unit
Wire pull 65 kN 14,612 lbs
Hauling speed 0-15 m/min 49 ft/min
Wire diameter 18 mm 11/16 inch
Drive Hydraulic motor
DREDGE SPUDS
Spud Length 13.8 m 45.3 ft
Spud diameter 457 mm 18 inch
Spud weight 2386 kg 5260 lbs
Cylinder lifting force 150 kN 33,72 lbs
Cylinder stroke 1.5 m 4.9 ft
Spud stroke 2.4 m 7.9 ft
FUEL
Type Diesel fuel
Tank capacity 16,000 liters 4226 gallon
DREDGE OPERATING CABIN
Total area 3.0 m2 32.3 sq-ft
Cooling Ventilation fan ( a/c optional )
Lights 1x interior light and 2x flood light
Additional Screen wipers
Instrumentation Dredging depth indication
Discharge pressure gauge
Vacuum pressure gauge
