audi s4 install - · PDF file Audi RS3/TT RS 400hp JB4 BETA Install Guide Applications: •...

Click here to load reader

  • date post

    23-Mar-2020
  • Category

    Documents

  • view

    11
  • download

    0

Embed Size (px)

Transcript of audi s4 install - · PDF file Audi RS3/TT RS 400hp JB4 BETA Install Guide Applications: •...

  • Audi RS3/TT RS 400hp JB4 BETA Install Guide

    Applications:

    • Audi RS3 8V2 400hp 2.5TFSI Evo

    • Audi TT RS 400hp 2.5TFSI

    Last Updated: 4/02/2019

    THIS PART IS LEGAL FOR USE ONLY IN COMPETITION RACING VEHICLES AS DEFINED UNDER CALIFORNIA LAW, AND IS

    NOT LEGAL FOR USE IN ANY OTHER MOTOR VEHICLE. California law defines a "racing vehicle" as "a competition vehicle not used

    on public highways." (Calif. Health & Safety Code 39048) This part may only be used on competition racing vehicles operated

    exclusively on a closed course in conjunction with a sanctioned racing event. Competition-only motor vehicles may not be driven to a

    racing event on a public highway and must be transported on a trailer or other carrier. USE OF THIS PART IN ANY OTHER VEHICLE

    MAY SUBJECT YOU TO FINES AND PENALTIES FOR VIOLATION OF FEDERAL

    AND/OR STATE LAW, WILL VOID YOUR WARRANTY FROM BURGER MOTORSPORTS, INC, AND CAN

    VOID YOUR VEHICLE'S WARRANTY. It is your responsibility to comply with all applicable federal and state laws relating to use of this

    part, and Burger Motorsports, INC hereby disclaims any liability resulting from the failure to use this part in compliance with all

    applicable federal and state laws.

  • Open the hood, lock the doors, place your key far enough from the car not to

    power up the ECU, and wait 3 min for the vehicles ECU to shut down.

    Instead of doing this step you can also disconnect the negative terminal of the

    battery. (note when connecting the battery again there will be dash warnings

    that will reset once you start moving).

    Start by lifting the plastic engine cover by pulling up at each corner.

  • SENSOR OVERVIEW:

    We will be connecting to three sensors in the engine bay (two if you did not opt

    for the BCM module) and the OBD wire coming from inside the car. One sensor

    at the end of the harness is unused and it can be tucked away.

  • BOOST SENSORS:

    The boost sensors plugs are removed by sliding out the grey lock in the

    direction of the arrow and then pressing it down to release the plug.

    Remove the stock plug and place the JB4 plug into the sensor. Click the original

    plug into the JB4 harness as pictured below.

    Sensor to the right of the overview has the rainbow patch wires (four different

    colours)

    Sensor to the left has the brown wire.

  • BCM Connection:

    The black plug goes into the valve and the brown plug goes to the original plug.

    The ground wire connects against the firewall ground assembly.

    For install neatness the BCM wires can be run under the intake pipe.

  • OBD WIRE:

    For the OBD wire you will need to pass the wire through to the engine bay from

    the inside of the car on the grommet found to the left of the brake pedal area. A

    wire can be attached to it to find it easier in the engine bay. The carpet will need

    to be lifted slightly.

    The small plug at the end connects to the JB4 on the small Molex plug with the

    brown and green wire.

  • OBD EXIT FROM PASSENGER CONNECTION:

    DATA CABLE OR BLUETOOTH CONNECTION:

    The data cable connects by pulling the JB4 box open and connecting it to the

    circuit board. See forum link further down for interface download link.

    Bluetooth connect kit connects with the same manner attaching the blue wire

    with the positap to any of the red wires in the harness as seen below (indicated

    is a red wire coming from the connect kit). The phone app for IOS or Android will

    need to be purchased separate, it is called JB4 Mobile:

  • The install is now complete. If you disconnected the battery on start up you will

    have several dash warnings. The modules will reset themselves as you drive of

    and the ECU completes a safety test.

    Map information, Bluetooth module and general information on the unit can be

    found at our support forum here:

    https://www.n54tech.com/forums/showthread.php?t=56120

    For technical support and sales queries email [email protected]

    https://www.n54tech.com/forums/showthread.php?t=56120 mailto:[email protected]