Audi Q5/SQ5 Ziza LED Interior Lighting Kit Installation...

Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of those performing the repairs. Standard safety procedures and precautions (including use of safety goggles and proper tools and equipment) should be followed at all times to eliminate the possibility of personal injury or improper service which could damage the vehicle or compromise its safety.

Audi Q5/SQ5 Ziza LED InteriorLighting Kit Installation Instructions

R

AUDI Q5/SQ5 ZIZA LED INTERIOR LIGHT INSTALLATION

ECS TUNING 1000 SEVILLE RD. WADSWORTH, OH 44281 1.800.924.5172 WWW.ECSTUNING.COM 2

ES#2855349

INTRODUCTION

ADVANCED SKILLS &EXPERIENCE REQUIRED

BASIC SKILLS REQUIRED

PROFESSIONAL SKILLS & SPECIALTY TOOLS REQUIRED

ADVANCED SKILLS &EXPERIENCE REQUIRED

Installing this Q5/SQ5 Ziza LED interior light kit is a quick and easy project that requires only two basic tools. Enhance the interior of your Q5 or SQ5 by converting it to full LED lighting. The time investment to benefit ratio is strongly in your favor, as this will only take you about 45 minutes. Thank you for purchasing our ECS Tuning Ziza LED interior light kit. We appreciate your business!

This Ziza LED interior light kit from ECS Tuning offers the following:• Contains all LED’s to replace all the incandescent bulbs in the interior of your Q5/SQ5• Bright white lighting• Long lasting, high quality LED’s• Simple installation

Audi Q5/SQ5 Ziza LED I nterior Light Kit ES#2855349

SOME EXPERIENCE RECOMMENDED

BASIC SKILLS REQUIRED

SOME EXPERIENCE RECOMMENDED

PROFESSIONAL SKILLS & SPECIALTY TOOLS REQUIRED

http://www.ecstuning.com/Search/SiteSearch/ES2855349/ES2855349/

R



ES#2855349 R

TABLE OF CONTENTSKit Contents .....................................................................................................................pg.3

Required Tools ................................................................................................................pg.4

Audi Q5 LED Location Chart ......................................................................................pg.5

Installation Notes ..........................................................................................................pg.6

Preparation and Safety ................................................................................................pg.6

Doors, Luggage Compartment and Glove Box Bulbs ......................................pg.7

Vanity Light Bulbs .........................................................................................................pg.12

Front Dome and Map Light Bulbs ...........................................................................pg.14

Rear Dome and Map Light Bulbs .............................................................................pg.18

T10 “Wedge” Style LED’s (18)

Vanity Light 38mm Festoon (2)Front Dome Light 36mm Festoon (2)


R



ES#2855349

Below is a list of the tools we used to install the Audi Q5 Ziza LED Interior Light Kit.

• Hand Cleaner/Degreaser ..................................................................................... Available at ecstuning.com .................................................................ES#2167336

Note: The tools required for each step will be listed by the step number throughout these instructions.REQUIRED TOOLS

SHOP SUPPLIES AND MATERIALS

• Non-Marring Trim Tool ................................................................................................... Available at ecstuning.com ..........................................................................ES#2500877• Torx Drivers: T25 ............................................................................................................... Available at ecstuning.com ..........................................................................ES#11417





R



ES#2855349

AUDI Q5/SQ5 LED LOCATION CHART

You will be replacing the OE incandescent bulbs indicated here with the LED bulbs in your kit.

Luggage Compartment

Rear Dome and Map Light

Rear Dome and Map Light

Front Dome and Map Light

Glove Box

Vanity Light

LF Door Warning

LR Door WarningRR Door Warning

RF Door Warning

The front and rear footwell bulbs are already equipped from the factory with LED’s.

NOTE

Hatch

LR Puddle Lamp

LF Puddle Lamp

RR Puddle Lamp

RF Puddle Lamp


R



ES#2855349

INSTALLATION NOTES

GENERAL PREPARATION AND SAFETY INFORMATION

• Park your car in a safe, well lit, level area.• Shut the engine off and remove the key from the ignition switch.• Make sure any remote start devices are properly disabled.• Always wear safety glasses.• Make sure the parking brake is applied until the vehicle is safely lifted and supported.• If using an automotive lift, be sure and utilize the factory specified lift points. Lifting a vehicle in an incorrect location can cause damage to the suspension/running gear.• When lifting a vehicle using a jack, always utilize the factory specified lift points. Lifting a vehicle in an incorrect location can cause damage to the suspension/running gear. Always support the vehicle with jack stands.• Always read and follow all safety information and warnings for the equipment you are using.

Never get underneath a vehicle that is supported only by a jack. Always make sure that the vehicle is securely supported on jack stands.!

ECS Tuning cares about your health and safety. Please read the following safety information. This information pertains to automotive service in general, and while it may not pertain to every job you do, please remember and share these important safety tips.

• RH refers to the passenger side of the vehicle.• LH refers to the driver side of the vehicle.• Always use the proper torque specifications.• If applicable to this installation, torque specifications will be listed throughout the document and at the end as well.• Please read all of these instructions and familiarize yourself with the complete process before you begin.


R



ES#2855349

Inspect the picture of the lens on the right. Each one has a small cutout on one end to allow for insertion of a removal tool.

DOORS, LUGGAGE COMPARTMENT AND GLOVE BOX BULBS

Begin with either the doors or the luggage compartment. (The glove box lamp is difficult to see and replacing the others first will allow you to do it by “feel”). Locate the cutout in the lens you have chosen to start with, then Insert a non-marring trim tool into the cutout and gently pry it outwards. The complete lamp housing will easily pop out.

Step 1:

Step 2: Non-Marring Trim Tool

The picture on the right shows a closeup of the small cutout. They can also be seen easily by simply looking at the lens.

Close up view of cutout


R



ES#2855349

Disconnect the electrical connector (arrow) from the housing. Grasp the connector and wiggle slightly as you pull for easy removal.

Using the same non marring trim tool, gently pry between the housing and the tab on the end of the lens.

Step 3:

Step 4: Non-Marring Trim Tool



R



ES#2855349

Lift the lens off the housing.

Pull the original bulb out of it’s socket and insert the new LED bulb in it’s place. If you can not grasp the original bulb with your fingers, you may have to use the trim tool to push the bulb out from the bottom (arrow).

Step 5:

Step 6:

The bulb may be hot and can cause burns. Be sure to let it cool before removing.

CAUTION



R



ES#2855349

Re-install the lens onto the housing.

Plug the lamp back in and re-install it into place.

Step 7:

Step 8:

These LED bulbs are polarity specific. If they do not work when you plug them in, remove the bulb, flip it over, and re-install it.

NOTE



R



ES#2855349

Replace the remaining luggage compartment, hatch, and door warning, and puddle lamp bulbs in the same manner. Refer to page five for bulb location.

Install an LED bulb in the glove box lamp. It is difficult to see but can be easily removed in the same manner as the other lamps. The glove box lens does not have a housing attached to the underside, but rather a cover that’s removed with the non-marring trim tool, and then snapped back into place.

Step 9:

Step 10:

Non-Marring Trim Tool


Door Warning Light

Hatch Door

Puddle Lamp (under side

doors)



R



ES#2855349

Insert the non-marring trim tool into the cut-out section of the LH Vanity Light lens, and pry it out as you did with the doors and luggage compartment lights. Disconnect the electrical connector and remove the lens.

Remove the metal cover by lifting it out, then use your fingers to spread the bulb contacts and remove the bulb.

Step 1:

Step 2:


Be sure to thoroughly wash your hands before working near the headliner. It is extremely susceptible to picking up dirt, even light dirt that you cannot see.

NOTE

VANITY LIGHT BULBS


R



ES#2855349

Place the LED between the contacts with the LED’s pointing down and the heat sink facing up, spread the contacts slightly, install the LED, then re-install the metal cover.

Plug the lamp back in and re-install it into place. Repeat the steps for the other side.

Step 3:

Step 4:

VANITY LIGHT BULBS

Be sure to use the vanity light LED’s. Refer to page three for bulb identification.

NOTE


R



ES#2855349

Open the sunglass compartment and remove the T25 Torx fastener, then lower the overhead console to access the back side.

Locate the bulbs that are to be removed on the back side of the overhead console.

Step 1:

Step 2:

T25 Torx Driver

FRONT DOME AND MAP LIGHT BULBS

36mm Festoon

Bulb

W5W Wedge Bulb

T25 Torx fastener

Note the location of the hidden tabs for the dome light lens (red circles). This will be relevant in step six, page 16.

NOTE


R



ES#2855349

Twist the bulb socket 1/4 turn counter-clockwise then pull the map light bulb assembly from the console.

Pull the wedge-type bulb out of the socket and replace it with the LED by pushing it into place.

Step 3:

Step 4:

Tabs on socket align with slots in

console



R



ES#2855349

While aligning the tabs on the socket with the slots in the console (see step 3), place the socket into the console, then twist it 1/4 turn clockwise to lock it into place. Repeat the steps for the other bulb.

Remove the dome light lens by pushing it out from the inside as shown in the picture. Be sure to push on the lens near the hidden clips (identified in step one, page 14).

Step 5:

Step 6:

Installing

Removing




R



ES#2855349

The bulbs are held in place by two double-pronged contacts that extend outward. Remove them by pushing down on the end of each bulb from the inside. Install the LED’s in the same position between the two contacts, with the LED’s facing outward.

Replace the cover by inserting the four small tabs in first, then snapping the two large tabs into place.

Step 7:

Step 8:



R



ES#2855349

To replace the overhead console, insert the two rear tabs first, then guide the front section into place to engage the spring clips located on each side. Install the T25 Torx screw.

Place the trim tool into the cut-out on the front of the Rear Map Light/ Dome assembly, and push in the spring clip that holds the assembly in place. While holding in the spring clip, pry down and release the assembly.

Step 9:

Step 1:

T25 Torx Driver



REAR DOME AND MAP LIGHT BULBS


R



ES#2855349

Twist each bulb socket 1/4 turn counter-clockwise and remove it.

Pull the wedge-type bulb from the socket and replace it with a new LED by pushing it into place.

Step 2:

Step 3:



R



ES#2855349

Re install each socket by aligning the slots on the socket with the tabs on the Map Light/Dome assembly, and twisting 1/4 turn clockwise to lock it into place.

Place the plug end of the Map Light/Dome assembly in first, then guide the front section into place to engage the spring clip. Repeat the steps for the other side.

Step 4:

Step 5:

Tabs on receptacle align with

slots



These instructions are provided as a courtesy by ECS Tuning.

Your Audi Q5/SQ5 Ziza LED interior light installation is complete!

Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of those performing the repairs. Standard safety procedures and precautions (including use of safety goggles and proper tools and equipment) should be followed at all times to eliminate the possibility of personal injury or improper service which could damage the vehicle or compromise its safety.

Although this material has been prepared with the intent to provide reliable information, no warranty (express or implied) is made as to its accuracy or completeness. Neither is any liability assumed for loss or damage resulting from reliance on this material. SPECIFICALLY, NO WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER WARRANTY IS MADE OR TO BE IMPLIED WITH RESPECT TO THIS MATERIAL. In no event will ECS Tuning, Incorporated or its affiliates be liable for any damages, direct or indirect, consequential or compensatory, arising out of the use of this material.

Audi Q5/SQ5 Ziza LED Interior Lighting Kit Installation...

Documents

Transcript of Audi Q5/SQ5 Ziza LED Interior Lighting Kit Installation...