Atmel ATtiny1634 Appendix B - Microchip...

ATtiny1634

8-bit AVR® Microcontrollerwith 16K Bytes In-System Programmable Flash

DATASHEET APPENDIX B

Appendix B – ATtiny1634 Specification at 125C

This document contains information specific to devices operating at temperatures up to 125C. Only deviations are covered in this appendix, all other information can be found in the complete datasheet. The complete datasheet can be found at www.atmel.com.

8303D–AVR–02/2013

http://www.atmel.com

1. Memories

The EEPROM has an endurance of at least 50,000 write/erase cycles.

EEPROM may not be programmed at supply voltages below 2V.

2ATtiny1634 [DATASHEET APPENDIX B]8303D–AVR–02/2013

2. Lock Bits, Fuse Bits and Device Signature

Fuse bits may not be programmed at supply voltages below 2V.


3. Electrical Characteristics

3.1 Absolute Maximum Ratings*

3.2 DC Characteristics

Table 3-1. DC Characteristics. TA = -40 to +125C

Operating Temperature . . . . . . . . . . . -55C to +125C *NOTICE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent dam-age to the device. This is a stress rating only and functional operation of the device at these or other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rat-ing conditions for extended periods may affect device reliability.

Storage Temperature . . . . . . . . . . . . . -65C to +150C

Voltage on any Pin except RESETwith respect to Ground. . . . . . . . . . -0.5V to VCC+0.5V

Voltage on RESET with respect to Ground-0.5V to +13.0V

Maximum Operating Voltage . . . . . . . . . . . . . . . . 6.0V

DC Current per I/O Pin. . . . . . . . . . . . . . . . . . 40.0 mA

DC Current VCC and GND Pins . . . . . . . . . . 200.0 mA

Symbol Parameter Condition Min Typ (1) Max Units

VIL

Input Low VoltageVCC = 1.8 - 2.4V -0.5 0.2VCC (2) V

VCC = 2.4 - 5.5V -0.5 0.3VCC (2) V

Input Low Voltage,RESET Pin as Reset (4) VCC = 1.8 - 5.5V -0.5 0.2VCC (2)

VIH

Input High-voltageExcept RESET pin

VCC = 1.8 - 2.4V 0.7VCC(3) VCC +0.5 V

VCC = 2.4 - 5.5V 0.6VCC(3) VCC +0.5 V

Input High-voltageRESET pin as Reset (4) VCC = 1.8 - 5.5V 0.9VCC

(3) VCC +0.5 V

VOLOutput Low Voltage(5)

Except RESET pin(7)

Standard I/O: IOL = 10 mA, VCC = 5V0.6 V

High-sink I/O: IOL = 20 mA, VCC = 5V

Standard I/O: IOL = 5 mA, VCC = 3V0.5 V

High-sink I/O: IOL = 10 mA, VCC = 3V

VOHOutput High-voltage(6)

Except RESET pin(7)

IOH = -10 mA, VCC = 5V 4.3 V

IOH = -5 mA, VCC = 3V 2.5 V

ILILInput Leakage CurrentI/O Pin

VCC = 5.5V, pin low (absolute value) < 0.05 1 (8) µA

ILIHInput Leakage CurrentI/O Pin

VCC = 5.5V, pin high (absolute value) < 0.05 1 (8) µA


Notes: 1. Typical values at +25C.

2. “Max” means the highest value where the pin is guaranteed to be read as low.

3. “Min” means the lowest value where the pin is guaranteed to be read as high.

4. Not tested in production.

5. Although each I/O port can sink more than the test conditions (10 mA at VCC = 5V, 5 mA at VCC = 3V) under steady state conditions (non-transient), the sum of all IOL (for all ports) should not exceed 100 mA. If IOL exceeds the test con-ditions, VOL may exceed the related specification. Pins are not guaranteed to sink current greater than the listed test condition.

6. Although each I/O port can source more than the test conditions (10 mA at VCC = 5V, 5 mA at VCC = 3V) under steady state conditions (non-transient), the sum of all IOH (for all ports) should not exceed 100 mA. If IOH exceeds the test condition, VOH may exceed the related specification. Pins are not guaranteed to source current greater than the listed test condition.

7. The RESET pin must tolerate high voltages when entering and operating in programming modes and, as a conse-quence, has a weak drive strength as compared to regular I/O pins. See “Output Driver Strength” on page 20.

8. These are test limits, which account for leakage currents of the test environment. Actual device leakage currents are lower.

9. Values are with external clock using methods described in “Minimizing Power Consumption” on page 39. Power Reduction is enabled (PRR = 0xFF) and there is no I/O drive.

10.Bod Disabled.

RPU

Pull-up Resistor, I/O Pin VCC = 5.5V, input low 20 50 k

Pull-up Resistor, Reset Pin

VCC = 5.5V, input low 30 60 k

ICC

Supply Current,Active Mode (9)

f = 1MHz, VCC = 2V 0.23 0.4 mA

f = 4MHz, VCC = 3V 1.3 1.7 mA

f = 8MHz, VCC = 5V 4.3 6 mA

Supply Current,Idle Mode (9)

f = 1MHz, VCC = 2V 0.04 0.1 mA

f = 4MHz, VCC = 3V 0.26 0.4 mA

f = 8MHz, VCC = 5V 1.1 1.7 mA

Supply Current,Power-Down Mode(10)

WDT enabled, VCC = 3V 1.7 12 µA

WDT disabled, VCC = 3V 0.1 8 µA

Symbol Parameter Condition Min Typ (1) Max Units


3.3 Speed

The maximum operating frequency of the device is dependent on supply voltage, VCC . The relationship between supply voltage and maximum operating frequency is piecewise linear, as shown in Figure 3-1.

Figure 3-1. Maximum Frequency vs. VCC

3.4 Clock

Table 3-2. Accuracy of Calibrated 8MHz Oscillator

Notes: 1. See device ordering codes on page 37 for alternatives.

2. Accuracy of oscillator frequency at calibration point (fixed temperature and fixed voltage).

Table 3-3. Accuracy of Calibrated 32kHz Oscillator

2 MHz

1.8V 5.5V4.5V

8 MHz

2.7V

6 MHz

CalibrationMethod Target Frequency VCC Temperature Accuracy

FactoryCalibration

8.0MHz 2.7 – 4V 25C to +85C ±10% (1)

UserCalibration

Within:7.3 – 8.1MHz

Within:1.8 – 5.5V

Within:-40C to +85C

±1% (2)

CalibrationMethod Target Frequency VCC Temperature Accuracy

FactoryCalibration

32kHz 1.8 – 5.5V -40C to +85C ±35%


Table 3-4. External Clock Drive

3.5 System and Reset

Table 3-5. Enhanced Power-On Reset

Note: 1. Values are guidelines only.

2. Threshold where device is released from reset when voltage is rising.

3. The Power-on Reset will not work unless the supply voltage has been below VPOA.

Symbol Parameter

VCC = 1.8 - 5.5V VCC = 2.7 - 5.5V VCC = 4.5 - 5.5V

UnitsMin. Max. Min. Max. Min. Max.

1/tCLCL Clock Frequency 0 2 0 8 0 10 MHz

tCLCL Clock Period 500 125 100 ns

tCHCX High Time 200 40 20 ns

tCLCX Low Time 200 40 20 ns

tCLCH Rise Time 2.0 1.6 0.5 s

tCHCL Fall Time 2.0 1.6 0.5 s

tCLCLChange in period from one clock cycle to next

2 2 2 %

Symbol Parameter Min(1) Typ(1) Max(1) Units

VPOR Release threshold of power-on reset (2) 1.1 1.4 1.7 V

VPOA Activation threshold of power-on reset (3) 0.6 1.3 1.7 V

SRON Power-On Slope Rate 0.01 V/ms


4. Typical Characteristics

4.1 Current Consumption in Active Mode

Figure 4-1. Active Supply Current vs. VCC (Internal Oscillator, 8 MHz)

Figure 4-2. Active Supply Current vs. VCC (Internal Oscillator, 1 MHz)

1258525

-40

0

1

2

3

4

5

6

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC [V]

I CC [m

A]

1258525

-40

0

0,2

0,4

0,6

0,8

1

1,2

1,4

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC [V]

I CC [m

A]


Figure 4-3. Active Supply Current vs. VCC (Internal Oscillator, 32kHz)

4.2 Current Consumption in Idle Mode

Figure 4-4. Idle Supply Current vs. VCC (Internal Oscillator, 8 MHz)

125

8525

-40

0

0,005

0,01

0,015

0,02

0,025

0,03

0,035

0,04

0,045

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC [V]

I CC [m

A]

1258525

-40

0

0,2

0,4

0,6

0,8

1

1,2

1,4

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC [V]

I CC [m

A]


Figure 4-5. Idle Supply Current vs. VCC (Internal Oscillator, 1 MHz)

Figure 4-6. Idle Supply Current vs. VCC (Internal Oscillator, 32kHz)

1258525

-40

0

0,1

0,2

0,3

0,4

0,5

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC [V]

I CC [m

A]

125

8525

-40

0

0,01

0,02

0,03

0,04

0,05

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC

I CC


4.3 Current Consumption in Power-down Mode

Figure 4-7. Power-down Supply Current vs. VCC (Watchdog Timer Disabled)

Figure 4-8. Power-down Supply Current vs. VCC (Watchdog Timer Enabled)

125

85

25-400

0,5

1

1,5

2

2,5

3

3,5

4

4,5

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC [V]

I CC [u

A]

125

8525

-40

0

2

4

6

8

10

12

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC [V]

I CC [u

A]


4.4 Current Consumption in Reset

Figure 4-9. Reset Current vs. VCC (No Clock, excluding Reset Pull-Up Current)

4.5 Current Consumption of Peripheral Units

Figure 4-10. Watchdog Timer Current vs. VCC

125

8525

-40

0

0,5

1

1,5

2

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC [V]

I CC [m

A]

125

85

25

-40

0

0,001

0,002

0,003

0,004

0,005

0,006

0,007

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC

IccW

DT


Figure 4-11. Brownout Detector Current vs. VCC

Figure 4-12. Sampled Brownout Detector Current vs. VCC

12585

25-40

0

5

10

15

20

25

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC [V]

I CC [u

A]

125

85

25

-40

0

1

2

3

4

5

6

7

8

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC [V]

I CC [u

A]


Figure 4-13. AREF External Reference Pin Current (VCC = 5V)

4.6 Pull-up Resistors

Figure 4-14. I/O pin Pull-up Resistor Current vs. Input Voltage (VCC = 1.8V)

1258525

-40

0

20

40

60

80

100

120

140

160

1,5 2 2,5 3 3,5 4 4,5 5 5,5

AREF [V]

AR

EF

pin

curr

ent [

uA]

0

10

20

30

40

50

0 0,2 0,4 0,6 0,8 1 1,2 1,4 1,6 1,8 2

VOP [V]

I OP

[uA

]

25

-4085

125


Figure 4-15. I/O Pin Pull-up Resistor Current vs. input Voltage (VCC = 2.7V)

Figure 4-16. I/O pin Pull-up Resistor Current vs. Input Voltage (VCC = 5V)

25

-4085

125

0

20

40

60

80

0 0,5 1 1,5 2 2,5 3

VOP [V]

I OP

[uA

]

25

-4085

125

0

20

40

60

80

100

120

140

0 1 2 3 4 5 6

VOP [V]

I OP

[uA

]


Figure 4-17. Reset Pull-up Resistor Current vs. Reset Pin Voltage (VCC = 1.8V)

Figure 4-18. Reset Pull-up Resistor Current vs. Reset Pin Voltage (VCC = 2.7V)

25

-4085

125

0

10

20

30

40

0 0,2 0,4 0,6 0,8 1 1,2 1,4 1,6 1,8 2

VRESET [V]

I RES

ET [u

A]

25

-4085

125

0

10

20

30

40

50

60

0 0,5 1 1,5 2 2,5 3

VRESET [V]

I RES

ET [u

A]


Figure 4-19. Reset Pull-up Resistor Current vs. Reset Pin Voltage (VCC = 5V)

4.7 Input Thresholds

Figure 4-20. VIH: Input Threshold Voltage vs. VCC (I/O Pin, Read as ‘1’)

25

-4085

125

0

20

40

60

80

100

120

0 1 2 3 4 5 6

VRESET [V]

I RES

ET [u

A]

1258525

-40

0

0,5

1

1,5

2

2,5

3

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC [V]

Thre

shol

d [V

]


Figure 4-21. VIL: Input Threshold Voltage vs. VCC (I/O Pin, Read as ‘0’)

Figure 4-22. VIH-VIL: Input Hysteresis vs. VCC (I/O Pin)

1258525

-40

0

0,5

1

1,5

2

2,5

3

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC [V]

Thre

shol

d [V

]

1258525

-40

0

0,1

0,2

0,3

0,4

0,5

0,6

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC

Hys

teris

VIL

VIH

IO


Figure 4-23. VIH: Input Threshold Voltage vs. VCC (Reset Pin as I/O, Read as ‘1’)

Figure 4-24. VIL: Input Threshold Voltage vs. VCC (Reset Pin as I/O, Read as ‘0’)

1258525

-40

0

0,5

1

1,5

2

2,5

3

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC [V]

Thre

shol

d [V

]

125

8525

-40

0

0,5

1

1,5

2

2,5

3

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC [V]

Thre

shol

d [V

]


Figure 4-25. VIH-VIL: Input Hysteresis vs. VCC (Reset Pin as I/O)

4.8 Output Driver Strength

Figure 4-26. VOH: Output Voltage vs. Source Current (I/O Pin, VCC = 1.8V)

1258525

-40

0

0,1

0,2

0,3

0,4

0,5

0,6

0,7

0,8

0,9

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC

Hys

tere

sis

Res

et IO

VIL

VIH

12585

25

-40

0

0,5

1

1,5

2

543210

IOH [mA]

VO

H [V

]


Figure 4-27. VOH: Output Voltage vs. Source Current (I/O Pin, VCC = 3V)

Figure 4-28. VOH: Output Voltage vs. Source Current (I/O Pin, VCC = 5V)

1258525

-40

0

0,5

1

1,5

2

2,5

3

0186420

IOH [mA]

VO

H [V

]

1258525

-40

0

1

2

3

4

5

02510150

IOH [mA]

VO

H [V

]


Figure 4-29. VOL: Output Voltage vs. Sink Current (I/O Pin, VCC = 1.8V)

Figure 4-30. VOL: Output Voltage vs. Sink Current (I/O Pin, VCC = 3V)

125

85

25

-40

0

0,2

0,4

0,6

0,8

1

543210

IOL [mA]

VO

L [V

]

125

85

25

-40

0

0,2

0,4

0,6

0,8

1

0186420

IOL [mA]

VO

L [V

]


Figure 4-31. VOL: Output Voltage vs. Sink Current (I/O Pin, VCC = 5V)

Figure 4-32. VOH: Output Voltage vs. Source Current (Reset Pin as I/O, VCC = 1.8V

125

85

25

-40

0

0,2

0,4

0,6

0,8

1

02510150

IOL [mA]

VO

L [V

]

1258525

-40

0

0,5

1

1,5

2

18,06,04,02,00

IOH [mA]

VO

H [V

]


Figure 4-33. VOH: Output Voltage vs. Source Current (Reset Pin as I/O, VCC = 3V

Figure 4-34. VOH: Output Voltage vs. Source Current (Reset Pin as I/O, VCC = 5V

1258525

-40

0

0,5

1

1,5

2

2,5

3

18,06,04,02,00

IOH [mA]

VO

H [V

]

1258525

-40

0

1

2

3

4

5

18,06,04,02,00

IOH [mA]

VO

H [V

]


Figure 4-35. VOL: Output Voltage vs. Sink Current (Reset Pin as I/O, VCC = 1.8V)

Figure 4-36. VOL: Output Voltage vs. Sink Current (Reset Pin as I/O, VCC = 3V)

25

-40

0

0,2

0,4

0,6

0,8

1

18,06,04,02,00

IOL [mA]

VO

L [V

]

12585

125

85

25

-40

0

0,2

0,4

0,6

0,8

1

25,115,00

IOL [mA]

VO

L [V

]


Figure 4-37. VOL: Output Voltage vs. Sink Current (Reset Pin as I/O, VCC = 5V)

4.9 BOD

Figure 4-38. BOD Threshold vs Temperature (BODLEVEL = 4.3V)

125

85

25

-40

0

0,2

0,4

0,6

0,8

1

0 0,5 1 1,5 2 2,5 3 3,5 4

IOL [mA]

VO

L [V

]

VCC RISING

VCC FALLING

4,16

4,18

4,2

4,22

4,24

4,26

4,28

4,3

4,32

4,34

-40 -20 0 20 40 60 80 100 120 140

Temperature [C]

Thre

shol

d [V

]




VCC RISING

VCC FALLING

2,62

2,64

2,66

2,68

2,7

2,72

2,74

2,76

-40 -20 0 20 40 60 80 100 120 140

Temperature [C]

Thre

shol

d [V

]

VCC RISING

VCC FALLING

1,75

1,76

1,77

1,78

1,79

1,8

1,81

1,82

-40 -20 0 20 40 60 80 100 120 140

Temperature [C]

Thre

shol

d [V

]


Figure 4-41. Sampled BOD Threshold vs Temperature (BODLEVEL = 4.3V)


VCC RISING

VCC FALLING

4,25

4,26

4,27

4,28

4,29

4,3

4,31

4,32

4,33

-40 -20 0 20 40 60 80 100 120 140

Temperature [C]

Thre

shol

d [V

]

VCC RISING

VCC FALLING

2,7

2,71

2,72

2,73

2,74

2,75

2,76

-40 -20 0 20 40 60 80 100 120 140

Temperature [C]

Thre

shol

d [V

]



4.10 Bandgap Voltage

Figure 4-44. Bandgap Voltage vs. Supply Voltage

VCC RISING

VCC FALLING

1,77

1,775

1,78

1,785

1,79

1,795

1,8

-40 -20 0 20 40 60 80 100 120 140

Temperature [C]

Thre

shol

d [V

]

105

85

25

-40

1,04

1,045

1,05

1,055

1,06

1,065

1,07

1,075

1,08

1,085

1,5 2 2,5 3 3,5 4 4,5 5 5,5

Vcc [V]

Ban

dgap

[V]


Figure 4-45. Bandgap Voltage vs. Temperature (VCC = 3.3V)

4.11 Reset

Figure 4-46. VIH: Input Threshold Voltage vs. VCC (Reset Pin, Read as ‘1’)

1,04

1,045

1,05

1,055

1,06

1,065

1,07

-40 -20 0 20 40 60 80 100 120 140

Temperature [C]

Ban

dgap

Vol

tage

[V]

1258525

-40

0

0,5

1

1,5

2

2,5

3

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC [V]

Thre

shol

d [V

]


Figure 4-47. VIL: Input Threshold Voltage vs. VCC (Reset Pin, Read as ‘0’)

Figure 4-48. VIH-VIL: Input Hysteresis vs. VCC (Reset Pin )

125

8525

-40

0

0,5

1

1,5

2

2,5

3

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC [V]

Thre

shol

d [V

]

0

0,1

0,2

0,3

0,4

0,5

0,6

0,7

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC [V]

Hys

tere

sis

[V]

125

85

25

-40


Figure 4-49. Minimum Reset Pulse Width vs. VCC

4.12 Analog Comparator Offset

Figure 4-50. Analog Comparator Offset vs. VIN (VCC = 5V)

1258525

-40

0

500

1000

1500

2000

2500

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC [V]

Pul

sew

idth

[ns]

12585

25

-40

0

10

20

30

40

50

60

70

80

0 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5

VIN [V]

Offs

et [m

V]


Figure 4-51. Analog Comparator Offset vs. VCC (VIN = 1.1V)

Figure 4-52. Analog Comparator Hysteresis vs. VIN (VCC = 5.0V)

1258525

-40

0

1

2

3

4

5

6

7

8

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC [V]

Offs

et [m

V]

12585

25

-40

0

5

10

15

20

25

30

35

40

45

0 0,5 1 1,5 2 2,5 3 3,5 4 4,5 5

VIN [V]

Hys

tere

sis

[mV

]


4.13 Internal Oscillator Speed

Figure 4-53. Calibrated Oscillator Frequency (Nominal = 8MHz) vs. VCC

Figure 4-54. Calibrated Oscillator Frequency (Nominal = 8MHz) vs. Temperature

1258525

-40

7,9

8

8,1

8,2

8,3

8,4

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC [V]

Freq

uenc

y [M

Hz]

5.0 V

3.0 V

7,9

7,95

8

8,05

8,1

8,15

8,2

-40 -20 0 20 40 60 80 100 120 140

Temperature [°]

Freq

uenc

y [M

Hz]


Figure 4-55. Calibrated Oscillator Frequency (Nominal = 1MHz) vs. VCC

Figure 4-56. Calibrated Oscillator Frequency (Nominal = 1MHz) vs. Temperature

1258525

-40

0,97

0,98

0,99

1

1,01

1,02

1,03

1,04

1,05

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC [V]

Freq

uenc

y [M

Hz]

5.0 V

3.0 V

1.8 V

970000

980000

990000

1000000

1010000

1020000

1030000

-40 -20 0 20 40 60 80 100 120 140

Temperature [°]

Freq

uenc

y


Figure 4-57. ULP Oscillator Frequency (Nominal = 32kHz) vs. VCC

Figure 4-58. ULP Oscillator Frequency (Nominal = 32kHz) vs. Temperature

125

85

25

-40

27000

28000

29000

30000

31000

32000

33000

1,5 2 2,5 3 3,5 4 4,5 5 5,5

VCC [V]

F RC [H

z]

27000

28000

29000

30000

31000

32000

33000

-40 -20 0 20 40 60 80 100 120 140

Temperature [°]

F RC [H

z]


5. Ordering Information

Notes: 1. For speed vs. supply voltage, see section 3.3 “Speed” on page 6.

2. All packages are Pb-free, halide-free and fully green, and they comply with the European directive for Restriction of Hazardous Substances (RoHS).

3. Denotes accuracy of the internal oscillator. See Table 3-2 on page 6.

4. Code indicators:

F: matte tin

R: tape & reel

5. Can also be supplied in wafer form. Contact your local Atmel sales office for ordering information and minimum quantities.

5.1 ATtiny1634

Speed (MHz) (1) Supply Voltage (V) Temperature Range Package (2) Accuracy (3) Ordering Code (4)

12 1.8 – 5.5Industrial

(-40C to +125C) (5) 20M1±10% ATtiny1634-MF

±10% ATtiny1634-MFR

Package Type

20M1 20-pad, 4 x 4 x 0.8 mm Body, Quad Flat No-Lead / Micro Lead Frame Package (QFN/MLF)


6. Datasheet Revision History

Revision History

8303D: Appendix B – 10/12 Initial revision


Atmel Corporation

1600 Technology Drive

San Jose, CA 95110

USA

Tel: (+1) (408) 441-0311

Fax: (+1) (408) 487-2600

www.atmel.com

Atmel Asia Limited

Unit 01-5 & 16, 19F

BEA Tower, Millennium City 5

418 Kwun Tong Roa

Kwun Tong, Kowloon

HONG KONG

Tel: (+852) 2245-6100

Fax: (+852) 2722-1369

Atmel Munich GmbH

Business Campus

Parkring 4

D-85748 Garching b. Munich

GERMANY

Tel: (+49) 89-31970-0

Fax: (+49) 89-3194621

Atmel Japan G.K.

16F Shin-Osaki Kangyo Bldg

1-6-4 Osaki, Shinagawa-ku

Tokyo 141-0032

JAPAN

Tel: (+81) (3) 6417-0300

Fax: (+81) (3) 6417-0370

© 2013 Atmel Corporation. All rights reserved. / Rev.: 8303D–AVR–02/2013

Atmel®, Atmel logo and combinations thereof, Enabling Unlimited Possibilities®, AVR®, tinyAVR® and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.

Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and products descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.

Atmel ATtiny1634 Appendix B - Microchip...

Documents

Transcript of Atmel ATtiny1634 Appendix B - Microchip...