armor START-UP cHecKlIst - Lochinvar · 2018. 3. 28. · clearances Measure and record (inches) the...
1
CLEARANCES Measure and record (inches) the service clearances from the nearest obstruction (min. 24” required for service): Front: __________ L Side: __________ Top: __________ Rear: __________ R Side: __________ Comments/Corrections needed for service clearances: _____________________________________________________ _____________________________________________________ General Job Notes: ______________________________________ _____________________________________________________ START-UP PERFORMED BY: Company: ____________________________________________ Name: ____________________________________________ Phone: ____________________________________________ START-UP APPROVED BY: Company: ____________________________________________ Name: ____________________________________________ Phone: ____________________________________________ COMBUSTION Low Fire: O 2 _________________ CO ppm _________________ CO 2 _________________ High Fire: O 2 _________________ CO ppm _________________ CO 2 _________________ Comments/Corrections needed for gas supply, water or electricity: _____________________________________________________ _____________________________________________________ _____________________________________________________ VENTING (Select the venting option being used): Vertical Direct Vent - two pipe vertical termination Horizontal Direct Vent – two pipe sidewall termination Concentric Vent Vertical – single pipe vertical termination Concentric Vent Horizontal – single pipe sidewall termination Vertical Vent w/ Sidewall Air – single pipe vertical termination w/ single pipe combustion air supply Vertical Vent w/ Room Air – single pipe vertical termination Horizontal Vent w/ Room Air – single pipe sidewall termination Air Inlet Air Inlet Total Eqv. Dia. (in.): Material: Length (ſt.): ___________ _______________________ ___________ Flue Flue Total Eqv. Dia. (in.): Material: Length (ſt.): ___________ _______________________ ___________ Comments/Corrections needed for air inlet or vent piping: _____________________________________________________ _____________________________________________________ Job Name: _____________________________________________ Address: _____________________________________________ City: _______________________ ST: _______ Zip: ________ Model Number: ________________________________________ Serial Number: ________________________________________ Start-up Date: ________________________________________ ARMOR START-UP CHECKLIST WATER & ELECTRICAL Water Pipe Dia. (in.): ___________ Tank sensor installed in storage tank? At full fire, read and record - Inlet Temp: __________ Outlet Temp: __________ Delta T: __________ Supply VAC: __________ Total Amp draw: __________ Y N OVERVIEW Retrofit New Project How many units are installed at this location? Boiler(s): _____________ Water Heater(s): _____________ Inspect gas pipe, regulator and meter sizing. Is it sized correctly for the Btu/Hr requirement? Y N GAS SUPPLY Gas Pipe Dia. (in.): ____________ Is there an inlet gas lockup regulator on the supply? If Yes, is it ten feet upstream from the appliance? Record in. of water column - Static Pressure: ________ Dynamic Pressure: ________ Y N Y N is Startup Sheet is for use only by a qualified heating installer/service technician. Refer to the Installation and Operation Manual for your reference. Have this unit serviced/inspected by a qualified service technician, at least annually. Failure to comply with the above could result in severe personal injury, death, or substantial property damage. WARNING ! Send completed form to: Email: [email protected] Fax: (615) 882-2963 Mail: Service Dept/Lochinvar 300 Maddox Simpson Pkwy. Lebanon, TN 37090 Internal Use: S/O #: _____________________ Routed: _____________________ Tech: _____________________ App: Denied: — e information on this form verifies operation of the Lochinvar product only. — is does not imply other system components or overall system operation is certified. Component and system verification should be performed by the designated commissioning agent or installing contractor.
Transcript of armor START-UP cHecKlIst - Lochinvar · 2018. 3. 28. · clearances Measure and record (inches) the...
-
clearances Measure and record (inches) the service clearances from the nearest obstruction (min. 24” required for service):
Front: __________ L Side: __________ Top: __________
Rear: __________ R Side: __________Comments/Corrections needed for service clearances:
_____________________________________________________
_____________________________________________________
General Job Notes: ______________________________________
_____________________________________________________
start-up performed by:
Company: ____________________________________________
Name: ____________________________________________
Phone: ____________________________________________
start-up approved by:
Company: ____________________________________________
Name: ____________________________________________
Phone: ____________________________________________
combustIonLow Fire:
O2 _________________CO ppm _________________CO2 _________________
High Fire:
O2 _________________CO ppm _________________CO2 _________________
Comments/Corrections needed for gas supply, water or electricity:
_____________________________________________________
_____________________________________________________
_____________________________________________________
ventIng (Select the venting option being used):
Vertical Direct Vent - two pipe vertical termination
Horizontal Direct Vent – two pipe sidewall termination
Concentric Vent Vertical – single pipe vertical termination
Concentric Vent Horizontal – single pipe sidewall termination
Vertical Vent w/ Sidewall Air – single pipe vertical termination w/ single pipe combustion air supply
Vertical Vent w/ Room Air – single pipe vertical termination
Horizontal Vent w/ Room Air – single pipe sidewall termination
Air Inlet Air Inlet Total Eqv.Dia. (in.): Material: Length (ft.):
___________ _______________________ ___________Flue Flue Total Eqv.Dia. (in.): Material: Length (ft.):
___________ _______________________ ___________Comments/Corrections needed for air inlet or vent piping:
_____________________________________________________
_____________________________________________________
Job Name: _____________________________________________
Address: _____________________________________________
City: _______________________ ST: _______ Zip: ________
Model Number: ________________________________________
Serial Number: ________________________________________
Start-up Date: ________________________________________
armor START-UP cHecKlIst
water & electrIcalWater Pipe Dia. (in.): ___________
Tank sensor installed in storage tank?
At full fire, read and record - Inlet Temp: __________
Outlet Temp: __________
Delta T: __________
Supply VAC: __________
Total Amp draw: __________
Y
N
overvIew
Retrofit New Project
How many units are installed at this location? Boiler(s): _____________ Water Heater(s): _____________
Inspect gas pipe, regulator and meter sizing.Is it sized correctly for the Btu/Hr requirement?
Y
N
gas supply
Gas Pipe Dia. (in.): ____________
Is there an inlet gas lockup regulator on the supply?
If Yes, is it ten feet upstream from the appliance?
Record in. of water column -
Static Pressure: ________
Dynamic Pressure: ________
Y
N
Y
N
This Startup Sheet is for use only by a qualified heating installer/service technician. Refer to the Installation and Operation Manual for your reference.
Have this unit serviced/inspected by a qualified service technician, at least annually. Failure to comply with the above could result in severe personal injury, death, or substantial property damage.
WARNING !
Send completed form to:
email: [email protected]
Fax: (615) 882-2963
Mail: Service Dept/Lochinvar 300 Maddox Simpson Pkwy. Lebanon, TN 37090
Internal Use:S/O #: _____________________
Routed: _____________________
Tech: _____________________
App: Denied:— The information on this form verifies operation of the Lochinvar product only. —
This does not imply other system components or overall system operation is certified. Component and system verification should be performed by the designated commissioning agent or installing contractor.
yrobertsTypewritten TextAWII STARTUP REV A
yrobertsTypewritten Text
Job Name: Model Number: Address: Serial Number: City: ST: Zip: Startup Date: Gas Pipe Dia in: Water Pipe Dia: Overview: OffLow Fire o2: Lockup: OffLow Fire CO: Boilers: Low Fire CO2: Water Heaters: Inlet Temp: Upstream: OffOutlet Temp: Delta T: High Fire o2: Meter Sizing: OffStatic Pressure: Supply VAC: High Fire CO: Dynamic Pressure: Total Amp draw: High Fire co2: Gas Comments: Front: L Side: Top: Venting: OffRear: R Side: Clearance Comments: General Job Notes: Gen job notes cont: Company: Air inlet dia: Air inlet matl: Total Eqv length Air Inlet: Name: Phone: Flue Material: Flue Dia: Flue Length: Company_2: Piping Comments: Name_2: Phone_2: SO: Routed: Tech: Approved: OffDenied: OffSave:
