Are you working in flammable work environment
-
Upload
terry-penney -
Category
Law
-
view
57 -
download
0
Transcript of Are you working in flammable work environment
Are you Working in Flammable Work Environment
Did EVERYTONE Talk about Safety
P bar Y Safety Consultants Alberta Canada
HEIRARCHY OF CHEMICAL CONTROLS
LAWS
REGULATIONS
INDUSTRY CODES
GOOD BUSINESS
PRACTICES
CHEMICAL MANAGEMENT
P B A R Y S A F E T Y C O N S U L T A N T S A L B E R T A C A N A D A
Proper and Safe Chemical Management
Part of the facility culture
Part of every employee’s activity
Recognition of safety improvement
Safety is everyone’s responsibility.
CHEMICAL MANAGEMENT
P B A R Y S A F E T Y C O N S U L T A N T S A L B E R T A C A N A D A
Fuel
Any combustible material – solid, liquid or gas
Oxygen
The air we breathe is
about 21% oxygen –
fire needs only
16% oxygen
Heat
The energy necessary to
increase the temperature of
fuel to where sufficient
vapors are given off for
ignition to occur
Each of these three elements must be present at
the same time to have a fire. A fire will burn until
one or more of the elements is removed.
P B A R Y S A F E T Y C O N S U L T A N T S A L B E R T A C A N A D A
PROPERTIES OF OXYGEN
OXYGEN SUPPORTS LIFE
Oxygen is essential to life
Its normal concentration in the air webreathe is approximately 21 %
We can breathe in a 50-60% oxygenenriched atmosphere for several
hours under medical care(oxygen therapy)
But it is dangerous to do sowithout knowing the associatedrisks due to oxygen enrichment !
P B A R Y S A F E T Y C O N S U L T A N T S A L B E R T A C A N A D A
Oxygen…
!?!?
P B A R Y S A F E T Y C O N S U L T A N T S A L B E R T A C A N A D A
Well-designed and maintained ventilation systems remove flammable vapours from the workplace and reduce the risk of fire and health problems.
The amount and type of ventilation needed to minimize the hazards of flammable and combustible liquid vapours depend on such things as the kind of job, the kind and amount
of materials used, and the size and layout of the work area.
An assessment of the specific ways flammable and combustible liquids are stored, handled, used and disposed of is the best way to find out if existing ventilation controls (and other
hazard control methods) are adequate.
Some workplaces may need a complete system of hoods and ducts to provide acceptable ventilation. If flammable vapours are likely to condense, the ducts should have welded
joints. Other workplaces may only require a single, well-placed exhaust fan. Use non-ferrous fan blades and shrouds (housing), and explosion-proof electrical equipment in ventilation systems for these liquids. Regular cleaning of the ducts, filters, plenums, etc. will decrease
the severity of any fires and will reduce the likelihood of spontaneous combustion if some self-heating material is present. Ventilation equipment used to handle solvent vapours
should meet the relevant fire code requirements.
WHY IS GOOD VENTILATION
IMPORTANT?
P B A R Y S A F E T Y C O N S U L T A N T S A L B E R T A C A N A D A
Combustible
materials…
P B A R Y S A F E T Y C O N S U L T A N T S A L B E R T A C A N A D A
For a flammable or combustible liquid fire to start, a mixture of vapour and air must be ignited. There are many possible ignition sources:
Sparks from electrical tools and equipment.
Sparks, arcs and hot metal surfaces from welding and cutting.
Tobacco smoking.
Open flames from portable torches and heating units, boilers, pilot lights, ovens, and driers.
Hot surfaces such as boilers, furnaces, steam pipes, electric lamps, hot plates, irons, hot ducts and flues, electric coils and hot bearings.
Embers and sparks from incinerators, foundry cupolas, fireboxes and furnaces.
Sparks from grinding and crushing operations.
Sparks caused by static electricity from rotating belts, mixing operations or improper transfer of flammable or hot combustible liquids.
You can eliminate many of these ignition sources by:
Removing open flames and spark-producing equipment.
Not smoking around these liquids.
Using approved explosion-proof equipment in hazardous areas.
WHAT ARE IGNITION SOURCES?
P B A R Y S A F E T Y C O N S U L T A N T S A L B E R T A C A N A D A
COMPATIBILITY OF MATERIALS
Only certain materials are suitable for use in oxygen service
Most materials - including metals - will burn in oxygen enriched atmospheres
• Equipment and materialcontaminated with oil orgrease can ignite easily andburn with explosive violencein oxygen enriched atmospheres
P B A R Y S A F E T Y C O N S U L T A N T S A L B E R T A C A N A D A
Equipment must be cleaned for oxygen service
using approved cleaning agents/methods
NEVER USE OIL OR GREASE TO
LUBRICATE OXYGEN EQUIPMENT!
• Check that any material/part or substance you intend to use is approved for oxygen service.
P B A R Y S A F E T Y C O N S U L T A N T S A L B E R T A C A N A D A
Ignition
sources…
P B A R Y S A F E T Y C O N S U L T A N T S A L B E R T A C A N A D A
Spontaneous combustion occurs when a material in contact with air can heat up sufficiently (without an outside heat source) to burn. The oils in some wastes and rubbish can slowly react with oxygen in the air. This reaction creates heat that can build up over time if the
wastes are left undisturbed. When the heat level in a "self-heating material" is high enough (i.e., when the temperature reaches the autoignition temperature), a fire may start.
For example, rag soaked with vegetable oil in the bottom of a pail could heat up enough to cause spontaneous combustion of the rag. However, the same oil-soaked rag would not be
expected to heat up on a clothes line because there would sufficient contact with moving air that would prevent heat from building up. An oil-soaked rag would not heat up if it were in
a tight bale because it would not have enough air. Similarly, wet or improperly cured hay stored loose (i.e., not baled) in a barn is susceptible to heating up enough to cause
spontaneous combustion. In the cases of spontaneous combustion of hay, grain and oil seeds, the source of heat comes from the action of microorganisms (e.g., bacteria, fungi) on materials having the right moisture and temperature conditions. Damp charcoal, meals (i.e., ground seeds), materials (fabrics, rags, cotton, etc.) soaked with paints containing drying oils
are some other examples of materials have a spontaneous combustion hazard.
WHAT IS SPONTANEOUS
COMBUSTION?
P B A R Y S A F E T Y C O N S U L T A N T S A L B E R T A C A N A D A
FLAMMABLE LIQUIDS
Flammable liquids can cause a fire or explosion, and like many other
substances, they can also cause serious health effects from overexposure.
Note: On the NFPA diamond label, a fire hazard
rating of 3 or 4 denotes a flammable liquid.
3
FLAMMABLE LIQUIDS
A flammable liquid is any liquid having a flashpoint below 100°F.
Exception: Any mixture having components with flashpoints of 100°F or higher, the
total of which make up 99% or more of the total volume of the mixture.
Note: The flash point is the lowest temperature at which a liquid gives off
enough vapor to form a flammable mixture with air.
FLAMMABLE LIQUIDS
The vapors of flammable liquids often present
the most serious hazard.
The vapors can easily ignite or explode.
Flammable liquid vapors are heavier than air and may settle in low spots, or move a significant distance from the liquid itself.
EXPLOSIVE LIMITS
The explosive concentration of vapors in air has a lower and upper limit.
The Lower Explosive Limit (LEL) is the lowest concentration that will ignite.
The Upper Explosive Limit (UEL) is the highest concentration that will ignite.
If the vapor concentration is between the LEL and UEL, there is serious risk of fire
or explosion.
Explosive Limits
Above the Upper Explosive Limit, the mixture is too rich to burn
UPPER EXPLOSIVE LIMIT
Explosive Range
Below the Lower Explosive Limit, the mixture is too lean to burn
LOWER EXPLOSIVE LIMIT
FLAMMABLE LIQUIDS
Class 1A Liquids having flashpoints below
73°F and having a boiling point
below 100°F.
Class 1B Liquids having flashpoints below
73°F and having a boiling point at or
above 100°F.
Class 1C Liquids have flashpoints at or above
73°F and below 100°F.
COMBUSTIBLE LIQUIDS
Class II Liquids with flashpoints at or above
100°F and below 140°F.
Class III Liquids with flashpoints at or above
140°F
Class IIIA Those with flashpoints at or above
140°F and below 200°F.
Class IIIB Those with flashpoints at or above
200°F.
Store flammable and combustible liquids according to the laws, including building, fire, and electrical codes, that apply to your particular workplace. These laws specify the kinds of storage areas, such as storage rooms
and cabinets, allowed for these liquids. They also specify how to construct these storage areas and the amounts of flammable and combustible liquids in different types of containers that you can store in each kind of storage area. There may also be restrictions about the volume (how much) of product that can be stored.
For example: in some jurisdictions, containers used to store flammable or combustible liquids that are smaller than 230 litres, must meet the specifications in following regulations (for construction of the container):
the "Transportation of Dangerous Goods Regulations"
CSA B376-M "Portable containers for Gasoline and Other Petroleum Fuels"
CSA-B306 "Portable Fuel Tanks for Marine Use"
ULC/ORDC30 "Safety Containers"
Section 6 of CSA-B620 "Highway Tanks and Portable Tanks for the Transportation of Dangerous Goods"
Your local fire code will specify the quantity of liquid that may be stored at the workplace.
Containers of not more than 1 litre capacity used for flammable liquids (5 litres for combustible liquids) are generally exempt.
Ensure that all containers have WHMIS /GHS labels attached, where applicable.
STORAGE
P B A R Y S A F E T Y C O N S U L T A N T S A L B E R T A C A N A D A
Store flammable and combustible liquids in areas that are:
well ventilated to reduce vapour concentrations.
free of ignition sources.
cool (temperature controlled) and dry.
supplied with adequate firefighting and spill clean-up equipment.
away from elevators, building and room exits, or main aisles leading to exits.
accessible by firefighters.
labelled with suitable warning signs. For example: "No Smoking".
Avoid storing flammable and combustible liquids in basements. Ground floor storage is usually preferred as it provides easier access for emergency situations.
Inspect storage areas regularly for any deficiencies such as damaged or leaking containers, poor ventilation or non -approved equipment. Unapproved modifications or damage to approved or explosion-proof equipment or systems
could result in unintended hazardous conditions. Correct all deficiencies as soon as possible.
It may be possible to store small amounts of flammable liquids (less than 235 litres or about 62 U.S. gallons) and combustible liquids (less than 470 litres or about 124 U.S. gallons) in approved containers in specially designed
storage cabinets near their point of use.
Volatile, flammable liquids are sometimes stored in refrigerators. Use specially designed and approved refrigerators (generally described as "laboratory safe") for this. Standard domestic refrigerators contain many ignition sources and
should not be used for storing flammable solvents.
STORE IT CORRECTLY
P B A R Y S A F E T Y C O N S U L T A N T S A L B E R T A C A N A D A
STORAGE AREAS
Flammables should be stored in an approved cabinet in a
cool, well ventilated area to avoid pressure buildup and
vaporization.
PRECAUTIONS
To bond containers, each container is wired together and
one container is connected to a good ground point to allow
any charge to drain away safely.
Because there is no easy way to bond plastic containers, their use
should be limited to smaller sizes (no more than 4L).
PREVENTIVE MEASURES
Materials that contribute to a flammable liquid fire should not be stored
with flammable liquids. For example,
Oxidizers
Organic peroxides
Drums of flammable liquids should have pressure- and vacuum-relief venting installed. Normally, this is done as soon as the drum is opened for dispensing. If a stored drum will be exposed to heat sources or large temperature changes, relief
venting may be needed.
Storing a full drum in direct sunlight or near other heat sources can increase vapour levels in the drum. This leads to an increase in pressure that could, in
extreme cases, cause the drum to rupture. A buildup in pressure can also result in vapour shooting out into the face or onto the clothing of the person opening the
drum. A pressure-relief vent prevents this increase in pressure.
Vacuum-relief vents are also useful. If a drum of flammable liquid is subjected to sudden cooling, a partial vacuum can form inside it. This could, in extreme cases, cause the drum to collapse and leak. Also, for proper dispensing of liquids, the space left behind by the liquid in the drum must be replaced with air so that no vacuum forms. There are different kinds of pressure-relief and vacuum-relief devices, including combination types, available from safety equipment retailers.
WHY IS VENTING OF FLAMMABLE
LIQUID DRUMS IMPORTANT?
P B A R Y S A F E T Y C O N S U L T A N T S A L B E R T A C A N A D A
Why should I inspect the container?
Check all containers used for flammable and combustible liquids regularly to make sure that they are not damaged, that spring-operated mechanisms are working properly and that
flame arresters are not broken. Safety container manufacturers will provide detailed ways to inspect their equipment for safe operation.
Why should I label containers?
Properly label all containers used for flammable and combustible liquids. This helps prevent accidentally mixing one chemical with another and reduces the chances of mistaking one liquid for another. Plainly mark the name of the liquid and its hazard on the container.
Keep the label clean so that it can be easily seen at all times. Never use a container for any liquid except the one that is marked on the label.
Using unsuitable containers such as jam jars, saucers, open cans, buckets or pails is a dangerous practice. Open containers allow hazardous vapours to escape. Breakable
containers increase the chance of serious spills.
KNOW THE PROPER CONTENTS
P B A R Y S A F E T Y C O N S U L T A N T S A L B E R T A C A N A D A
How do I dispose of waste material safely?
Store waste flammable and combustible liquids in the same way as unused flammable and combustible liquids. Clean drums made of compatible material can be used to store waste liquids if they are vented, grounded and
bonded similarly to dispensing drums. Approved safety disposal cans are also available for waste liquids.
Place cloth, paper and other solid materials that are soaked with flammable and combustible liquids in approved oily waste disposal cans. These are made of metal and have self-closing lids. Do not overfill them,
and empty them at least at the end of every workday to reduce the chance of spontaneous combustion.
Clearly label all waste containers with their contents.
Be careful with "empty" flammable and combustible liquid containers. They may contain enough liquid to create an explosion hazard. Only about 14 mL (0.5 fluid ounce) of liquid are needed to give enough vapour to form an explosive atmosphere in a 182-litre (40-gallon) drum. This amount can easily be trapped in a seam or be present as a very thin film on the inner surface of the drum. Do not perform any work (welding, cutting,
drilling, soldering) on an "empty" liquid container until all liquid and vapours have been cleaned out. Contact the chemical manufacturer or supplier for the best way to do this.
Never pour waste flammable liquids down sinks or drains. Dispose of them through hazardous waste collection and disposal companies.
WASTE
P B A R Y S A F E T Y C O N S U L T A N T S A L B E R T A C A N A D A
What are basic safety practices for flammable and combustible liquids?
Following these basic safe practices will help protect you from the hazards of flammable and combustible liquids:
Obtain and read the Material Safety Data Sheets (MSDSs) or SDS for all of the materials you work with.
Be aware of all of the hazards (fire/explosion, health, chemical reactivity) of the materials you work with.
Know which of the materials that you work with are flammable or combustible liquids.
Eliminate ignition sources (sparks, smoking, flames, hot surfaces) when working with flammable and combustible liquids.
Use the smallest amount of flammable liquid necessary in the work area.
Keep storage areas cool and dry.
Store flammable and combustible liquids away from incompatible materials (e.g., oxidizers).
Use approved containers for disposal of rags and other work.
Store, handle and use flammable and combustible liquids in well-ventilated areas.
Use approved equipment, including labelled safety containers, for flammable and combustible liquids.
Keep containers closed when not in use.
Bond and ground metal containers when transferring flammable and combustible liquids.
Practice good housekeeping and equipment maintenance. Keep area clear of burnable materials.
Wear the proper personal protective equipment for each of the jobs you do.
WAY BEFORE IT IS TO LATE
P B A R Y S A F E T Y C O N S U L T A N T S A L B E R T A C A N A D A
Work safely !It is your life!
Fire Hazards of
Oxygen Enriched Atmospheres
P B A R Y S A F E T Y C O N S U L T A N T S A L B E R T A C A N A D A