Arches and Dome
-
Upload
harshil-mehta -
Category
Engineering
-
view
267 -
download
2
Transcript of Arches and Dome
Archesand
Dome
Harshil Mehta131010011010
Civil 6th Sem.
What is Arch…?An arch is structure that
spans a space and supports structure and weight above it.
Provides a structure which eliminates tensile stresses in spanning a great amount of open space.
All the forces are resolved into compressive stresses.
Force acting on arch
Elements of arches
Technical Terms Keystone: A keystone is the
wedge-shaped stone piece at the apex of an arch, which is the final piece placed during construction and locks all the stones into position, allowing the arch to bear weight.
Voussoirs: The voussoirs
are the wedge shaped units forming the arch.
Intrados: It is the inner curve of an arch.
Extrados: It is the outer curve of an arch.
Springing stone: The springing stone or springer is the first voussoirs at springing level on either side of the arches.
Crown: Highest point of extrados or highest past of an arch.
Span : Clear horizontal distance between the two supports.
Rise :The vertical distance between the spring line of an arch and the keystone .
Failure of an archEVERY ELEMENT OF ARCH REMAINS IN
COMPRESSION. An arches fail due to: 1) Crushing of the masonry. 2) Sliding of voussoirs. 3) Rotation of some joints about an edge. 4) Uneven settlement of an abutment.
Failure of an archCrushing of the masonry: If the compressive
stress exceeds the safe crushing strength of the masonry unit and mortar , the arch will fail in crushing.
Sliding of voussoirs :To safeguard against sliding of voussoirs past each other due to transverse shear ,the voussoirs of greater height should be provided.
Rotation of some joints about an edge :Rotation can be prevented ,if the line of resistance is kept within intrados and extrados. Also, the line of thrust should be made to cross the joint away from the edge to prevent the crushing of that edge.
Failure of arches
Construction
Masonry work in arch should be carried up from both ends uniformly and keyed in the centre.
Defects in dressing should not be made good by mortar or chips.
The arch work should be kept thoroughly wet. so that no portion of the arch hardens and fully ,sets before the whole arch is completed.
From this consideration, it is desirable to employ a mortar which is slow setting.
Loading of Arches
Loading of arches should be gradual and so
regulated that at least 7 days should elapse
before 50% of design load.
At least 14 days should elapse before 75%of
design load comes on the arch, allowing full
design load only after 28 days of completion of
arch.
Main types of arches
Semi Circular Arch
Segmental arch or arch that is less than a semicircle
Flat arch
•A semi-circular arch is a half circle. This arch has an advantage over segmental arch that side thrust at the support is much less and thus side supports need not be very wide. •A flat arch, which is suitable only for small spans (say up to 1 meter) and light loads, has a horizontal extrados and slightly cambered intrados is employed mainly for spanning door and window openings in ordinary buildings.
DOME
A dome is an element of architecture that resembles the hollow upper half of a sphere.
Dome structures made of various materials have a long architectural lineage extending into prehistory.
A dome is a rounded vault made of curved segments, meaning an arch rotated around its central vertical axis.
What is DOME..?
Coffer Cupola Lantern Oculus Pendentive Rotunda Squinch Tholobate Whispering gallery
Elements of dome
Compound Dome Simple Dome
• Masonry domes were provided in the past to serve
as roof cover for large structures, when no other
structural means of bridging large spans were
available.
• With the advent of steel, reinforced concrete and
prestressed concrete, use of domes is not made now,
except on special architectural considerations in
case of monumental, religious and institutional
buildings.
• Construction technique of a dome is more or less
similar to that of an arch.
THANK YOU