Arcat Hybrid Trim Specifications-2017 - Geolaminc · b.! CCRR&0135.! c.! ... a.!...

06 82 00-12

SECTION 06 82 00

COMPOSITE TRIM

Display hidden notes to specifier. (Don't know how? Click Here)

Copyright 2017 - 2017 ARCAT, Inc. - All rights reserved

PART 1 GENERAL

1.1 SECTION INCLUDES

A. Architectural trim.

1.2 RELATED SECTIONS

A. Section 06100 - Rough Carpentry.

B. Section 06160 - Sheathing.

1.3 REFERENCES

A. Architectural Testing, Inc: 1. AA-676: Third party testing. 2. Manufacturer's Code Compliance Research Reports:

a. CCRR-0151. b. CCRR-0135. c. CCRR-0160.

B. ASTM International (ASTM): 1. ASTM D635 - Standard Test Method for Rate of Burning and/or Extent and

Time of Burning of Plastics in a Horizontal Position. 2. ASTM D1929 - Standard Test Method for Determining Ignition Temperature of

Plastics. 3. ASTM D2843 - Standard Test Method for Density of Smoke from the Burning

or Decomposition of Plastics. 4. ASTM D7032 - Standard Specification for Establishing Performance Ratings

for Wood-Plastic Composite and Plastic Lumber Deck Boards, Stair Treads, Guards, and Handrails.

5. ASTM E84 - Standard Test Method for Surface Burning Characteristics of Building Materials.

6. ASTM E330 - Standard Test Method for Structural Performance of Exterior Windows, Doors, Skylights and Curtain Walls by Uniform Static Air Pressure.

C. American Architectural Manufacturers Association (AAMA):

06 82 00-12

1. AAMA 509 - Voluntary Test and Classification Method of Drained and Back Ventilated Rain Screen Wall Cladding Systems.

D. Florida Building Code and Miami Dade County Approval.

E. International Code Council Evaluation Services (ICC-ES): 1. AC 10 - Acceptance Criteria for Quality Documentation. 2. AC 174 -Acceptance Criteria for Deck Board Span Ratings and Guardrail.

F. JIS International (Japanese Industrial Standards): 1. JIS A 5721 - Plastic Floor Parts. 2. JIS A 5909 - Dressed Particleboards. 3. JIS K 7112 - Plastics - Methods of Determining the Density and Relative

Density of Non-Cellular Plastics. 4. JIS K 7191 - Plastics - Determination of Temperature of Deflection Under

Load. 5. JIS K 7197 - Testing Method for Linear Thermal Expansion Coefficient of

Plastics by Thermomechanical Analysis.

1.4 SUBMITTALS

A. Submit under provisions of Section 01300.

B. Product Data: Manufacturer's data sheets on each product to be used, including: 1. Manufacturer's printed installation instructions, showing required preparation

and installation procedures. 2. Storage and handling requirements and recommendations. 3. Installation methods including anchorage details. 4. Cleaning and maintenance instructions.

C. Shop Drawings: Provide shop drawings indicating details of construction, anchorage and installation. Include statement that anchorage methods comply with applicable building codes and loadings for the type of framing and condition of the supporting construction and details.

D. Verification Samples: For each product specified, two samples 6 inches in length, representing materials, colors, patterns, textures, and finishes to be installed. 1. Closeout Submittals: Documentation of manufacturer's warranty.

1.5 QUALITY ASSURANCE

A. Installer: Minimum 2 years experience.

B. Mock-Up: Provide a mock-up for evaluation of surface preparation techniques and application workmanship. 1. Finish areas designated by Architect. 2. Do not proceed with remaining work until workmanship and appearance are

approved by Architect. 3. Subject to approval by Architect, mock-up may be retained as part of finish

work.

C. Pre-Installation Meetings: Conduct pre-installation meetings to verify project requirements, substrate conditions, construction documents, details and manufacturer's warranty requirements.

1.6 DELIVERY, STORAGE, AND HANDLING

A. Delivery: Deliver materials in manufacturer's original, unopened, undamaged

06 82 00-12

rolls/pallets with identification labels intact.

B. Storage and Protection: Store materials protected from exposure to harmful environmental conditions and at temperature and humidity conditions recommended by the manufacturer.

1.7 PROJECT CONDITIONS

A. Maintain environmental conditions (temperature, humidity, and ventilation) within limits recommended by manufacturer for optimum results. Do not install products under environmental conditions outside manufacturer's recommended limits.

1.8 WARRANTY

A. Manufacturer's Warranty: Manufacturer's standard limited 10 year warranty.

PART 2 PRODUCTS

2.1 MANUFACTURERS

A. Acceptable Manufacturer: Geolam, which is located at: 9 Shorncliffe Ave.;; Toronto, ON, Canada M4V 1S9;; Toll Free Tel: 877-627-3530;; Tel: 416-548-7450;; Fax: 416-548-7894;; Email: request info ([email protected]);; Web: www.geolaminc.com

B. Substitutions: Not permitted.

C. Requests for substitutions will be considered in accordance with provisions of Section 01600.

2.2 ARCHITECTURAL TRIM

A. Basis of Design: Soleo 1263 as manufactured by Geolam. 1. Hot Co-Extrusion of Aluminum and Wood Composite. 2. Physical Properties:

a. Specific Density Value: 0.046 lbs per cu in (1.27 gr per cu cm) per JIS K 7112.

b. Deformation Temperature: 241 degrees F (116 degrees C) per JIS K 7191.

c. Thermal Expansion Coefficient Value: 0.00002 in per F degrees (0.000036 mm per C degrees) per JIS K7197.

d. Moisture Absorption Value 24 hours at 65 degrees F (20 degrees C): 0.2 per JIS A5909.

e. Linear Expansion Value: Zero per JIS A5909. f. Aging Test Value: 5 percent per JIS 5721.

3. Dimensions: a. Width: 5 in (127 mm). b. Depth: 1-1/8 in (29 mm). c. Length: 9 ft 10 in (3000 mm). d. Length (ft / mm): ______

4. Color: Teak. 5. Color: Rosewood. 6. Color: Ebony. 7. Color: Moleskin.

B. Basis of Design: Soleo 6027 as manufactured by Geolam. 1. Hot Co-Extrusion of Aluminum and Wood Composite. 2. Physical Properties:

a. Specific Density Value: 0.046 lbs per cu in (1.27 gr per cu cm) per JIS

06 82 00-12

K 7112. b. Deformation Temperature: 241 degrees F (116 degrees C) per JIS K

7191. c. Thermal Expansion Coefficient Value: 0.00002 in per F degrees

(0.000036 mm per C degrees) per JIS K7197. d. Moisture Absorption Value 24 hours at 65 degrees F (20 degrees C):

0.2 per JIS A5909. e. Linear Expansion Value: Zero per JIS A5909. f. Aging Test Value: 5 percent per JIS 5721.

3. Dimensions: a. Width: 1-1/2 in (38 mm). b. Depth: 1-1/4 in (32 mm). c. Length: 9 ft 10 in (3000 mm). d. Length (ft / mm): ______.


C. Basis of Design: Soleo 6008 as manufactured by Geolam. 1. Hot Co-Extrusion of Aluminum and Wood Composite. 2. Physical Properties:






3. Dimensions: a. Width: 2 in (51 mm). b. Depth: 1-1/8 in (29 mm). c. Length: 9 ft 10 in (3000 mm). d. Length (ft / mm): ______.


D. Basis of Design: Soleo 6029 as manufactured by Geolam. 1. Hot Co-Extrusion of Aluminum and Wood Composite. 2. Physical Properties:






3. Dimensions:

06 82 00-12

a. Width: 2-3/8 in (60 mm). b. Depth: 1-1/4 in (32 mm). c. Length: 9 ft 10 in (3000 mm). d. Length (ft / mm): ______.


E. Basis of Design: Soleo 6030 as manufactured by Geolam. 1. Hot Co-Extrusion of Aluminum and Wood Composite. 2. Physical Properties:








F. Basis of Design: Soleo 6009 as manufactured by Geolam.1. Hot Co-Extrusion of Aluminum and Wood Composite. 2. Physical Properties:






3. Dimensions: a. Width: 4 in (102 mm). b. Depth: 1-1/4 in (32 mm). c. Length: 9 ft 10 in (3000 mm). d. Length (ft / mm): ______.


G. Basis of Design: Soleo 6033 as manufactured by Geolam.

06 82 00-12

1. Hot Co-Extrusion of Aluminum and Wood Composite. 2. Physical Properties:






3. Dimensions: a. Width: 8 in (203 mm). b. Depth: 1-3/8 in (35 mm). c. Length: 9 ft 10 in (3000 mm) d. Length (ft / mm): ______.


H. Basis of Design: Soleo 6026 as manufactured by Geolam. 1. Hot Co-Extrusion of Aluminum and Wood Composite. 2. Physical Properties:








I. Basis of Design: Soleo 6017 as manufactured by Geolam. 1. Hot Co-Extrusion of Aluminum and Wood Composite. 2. Physical Properties:





06 82 00-12




J. Basis of Design: Soleo 6034 as manufactured by Geolam. 1. Hot Co-Extrusion of Aluminum and Wood Composite. 2. Physical Properties:






3. Dimensions: a. Width: 4-1/8 in (105 mm). b. Depth: 2 in (51 mm). c. Length: 9 ft 10 in (3000 mm). d. Length (ft / mm):


K. Basis of Design: Soleo 6010 as manufactured by Geolam. 1. Hot Co-Extrusion of Aluminum and Wood Composite. 2. Physical Properties:






3. Dimensions: a. Width: 5 in (127 mm). b. Depth: 2 in (51 mm). c. Length: 9 ft 10 in (3000 mm). d. Length (ft / mm): ______.

4. Color: Teak. 5. Color: Rosewood. 6. Color: Ebony.

06 82 00-12

7. Color: Moleskin.

L. Basis of Design: Rondo 6029 as manufactured by Geolam. 1. Hot Co-Extrusion of Aluminum and Wood Composite. 2. Physical Properties:






3. Diameter Round: 2 in (51 mm). a. Length: 9 ft 10 in (3000 mm). b. Length (ft / mm):


M. Basis of Design: Careo 6014 as manufactured by Geolam. 1. Hot Co-Extrusion of Aluminum and Wood Composite. 2. Physical Properties:








N. Basis of Design: Careo 6011 as manufactured by Geolam. 1. Hot Co-Extrusion of Aluminum and Wood Composite. 2. Physical Properties:




d. Moisture Absorption Value 24 hours at 65 degrees F (20 degrees C):

06 82 00-12

0.2 per JIS A5909. e. Linear Expansion Value: Zero per JIS A5909. f. Aging Test Value: 5 percent per JIS 5721.

3. Dimensions: a. Width: 2 in (51 mm). b. Depth: 2 in (51 mm). c. Length: 9 ft 10 in (3000 mm) d. Length (ft / mm): ______.


O. Basis of Design: Careo 6018 as manufactured by Geolam. 1. Hot Co-Extrusion of Aluminum and Wood Composite. 2. Physical Properties:








P. FASTENERS:

1. Stainless Steel. Suggested Source. www.allfastinc.com.

PART 3 EXECUTION

3.1 EXAMINATION AND PREPARATION

A. Examine existing conditions and do not proceed with installation until substrates have been properly prepared and deviations from manufacturer's recommended tolerances are corrected. Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions.

B. If preparation is the responsibility of another installer, notify Architect in writing of deviations from manufacturer's recommended installation tolerances and conditions.

C. Commencement of installation constitutes acceptance of conditions.

3.2 INSTALLATION

A. Install in accordance with manufacturer's written instructions and recommendations

06 82 00-12

including but not limited to the following.

B. Protect installed work from damage due to subsequent construction activity on the site.

C. Clean using materials recommended by the manufacturer to remove stains, dirt and debris prior to final acceptance.

END OF SECTION

Arcat Hybrid Trim Specifications-2017 - Geolaminc · b.! CCRR&0135.! c.! ... a.!...

Documents

Transcript of Arcat Hybrid Trim Specifications-2017 - Geolaminc · b.! CCRR&0135.! c.! ... a.!...