ARC FLASH CALCULATIONS & LABELING...
Transcript of ARC FLASH CALCULATIONS & LABELING...
![Page 1: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/1.jpg)
•1
ARC FLASH CALCULATIONS & LABELING REQUIREMENTS
Presented by:
Edmund ElizaldeEYP Mission Critical Facilities, Inc.
Slides by:
Lonnie LindellSKM Systems Analysis, Inc.
![Page 2: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/2.jpg)
•2
Agenda
NEC 110.16NFPA 70EIEEE Std. 1584Arc Flash ExamplesArc Flash Calculation StepsQuestions & Discussion
![Page 3: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/3.jpg)
•3
Objectives
Understand Code RequirementsBe Aware of HazardsKnow How to Read Labels
![Page 4: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/4.jpg)
•4
110.16 Flash Protection. Switchboards, panelboards, industrial control panels, and motor control centers in other than dwelling occupancies, that are likely to require examination, adjustment, servicing, or maintenance while energized, shall be field marked to warn qualified persons of potential electric arc flash hazards. The marking shall be located so as to be clearly visible to qualified persons before examination, adjustment, servicing, or maintenance of the equipment.
FPN No. 1: NFPA 70E-2000, Electrical Safety Requirements for Employee Workplaces, provides assistance in determining severity of potential exposure, planning safe work practices, and selecting personal protective equipment.
FPN No. 2: ANSI Z535.4-1998, Product Safety Signs and Labels, provides guidelines for the design of safety signs and labels for application to products.
Reprinted from NEC® 2002
•NEC® 2002 Article 110.16
![Page 5: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/5.jpg)
•5
![Page 6: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/6.jpg)
•6
24 inch Flash Hazard Boundary3 cal/cm•2 Flash Hazard at 18 inches1DF PPE Level, 1 Layer 6 ozNomex ®,
Leather Gloves Faceshield480 VAC Shock Hazard when Cover is removed36 inch Limited Approach12 inch Restricted Approach - 500 V Class 00 Gloves1 inch Prohibited Approach - 500 V Class 00 Gloves
Equipment Name: Slurry Pump Starter
Arc Flash and Shock HazardAppropriate PPE Required
WARNING!
Courtesy E.I. du Pont de Nemours & Co.
![Page 7: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/7.jpg)
•7
NFPA 70E• Requirements for safe work practices• Addresses hazards:
– Shock– Arc Flash
• Requirements forshock and arc flashboundaries
• Requirements forpersonal protectiveequipment
• Incident Energy and flash boundarycalculations (<1000V, 5kA-106kA)
![Page 8: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/8.jpg)
•8
IEEE Std 1584 - 2002• Addresses Arc Flash Calculations:
Arcing Fault Incident energy Flash boundary
• Valid Ranges208 V to 15 kV700A to 106kAGap 13mm to 153mm
• Out of RangeUse Lee Equation
![Page 9: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/9.jpg)
What are the hazards as you approach electrical equipment
to perform work?
What are the hazards as you What are the hazards as you approach electrical equipment approach electrical equipment
to perform work?to perform work?
![Page 10: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/10.jpg)
•10
BoltedShort Circuit Arc Fault
A B A B
![Page 11: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/11.jpg)
•11
Electrical Arc
Copper Vapor:Solid to VaporExpands by67,000 times
Molten Metal35,000 °F
Pressure Waves
Sound Waves
Shrapnel
Hot Air-Rapid Expansion
Intense Light
![Page 12: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/12.jpg)
Arc Flash Incident
480 Volt System22,600 Amp Symmetrical FaultMotor Controller Enclosure6-Cycle Arcing Fault (0.1 sec)
![Page 13: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/13.jpg)
![Page 14: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/14.jpg)
![Page 15: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/15.jpg)
![Page 16: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/16.jpg)
![Page 17: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/17.jpg)
![Page 18: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/18.jpg)
![Page 19: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/19.jpg)
![Page 20: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/20.jpg)
•20
![Page 21: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/21.jpg)
•21
Clothed areas can be burned more
severely than exposed skin
![Page 22: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/22.jpg)
Arc Flash Incident
480 Volt System22,600 Amp Symmetrical FaultMotor Controller EnclosureCurrent Limiting Device with < ½ Cycle operation (.0083 sec). Note that Arcing Fault must be in current limiting range.
![Page 23: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/23.jpg)
![Page 24: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/24.jpg)
![Page 25: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/25.jpg)
![Page 26: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/26.jpg)
![Page 27: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/27.jpg)
![Page 28: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/28.jpg)
![Page 29: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/29.jpg)
•29
What Are the OSHA Regulations and NFPA 70E Requirements for Working
on “Live” Equipment?
![Page 30: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/30.jpg)
•30
Safe Work Practices OSHA 1910.333 (a) (1) & NFPA 70E 2-1.1.1
not to work “hot” or “live” except when:
1. De-energizing introduces additionalor increased hazards
2. Infeasible due toequipment designor operationallimitations
![Page 31: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/31.jpg)
Flash Protection Boundary (FPB)Must wear appropriate PPEFPB dependent on fault level and time duration.
Flash Protection Boundary (FPB)Must wear appropriate PPEFPB dependent on fault level and time duration.
Equi
pmen
t
Limited Shock Boundary: Qualified or Unqualified Persons** Only if accompanied by Qualified Person
Prohibited Shock Boundary: Qualified Persons Only. PPE asif direct contact with live part
Restricted Shock Boundary: Qualified Persons Only
Note: shock boundaries dependent on system voltage level
![Page 32: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/32.jpg)
•32
Incident Energy
• Energy Per Unit of Area Received On A Surface Located A Specific Distance Away From The Electric Arc, Both Radiant And Convective, in Units of cal/cm2.
![Page 33: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/33.jpg)
•33
Cal/cm2
• 1.2 cal/cm2 - Second Degree Burn• 3 cal/cm2 - 1% probability ignition
of light weight cotton shirt.• 6 cal/cm2 - Arc Rating of 1 layer 6
oz/yd2 aramid.• 32 cal/cm2 - Arc Rating of one layer
6 oz/yd2 plus 4.5 oz/yd2 aramid over a cotton T-shirt.
![Page 34: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/34.jpg)
•34
Highlights of changes impacting arc flash
hazards PPE in the 2000 edition of NFPA70E
![Page 35: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/35.jpg)
NFPA70E - 2000
Where it has been determined that work will be performed within the flash protection boundary, the flash hazard analysis shall determine, and the employer shall document, the incident energy exposure of the worker
![Page 36: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/36.jpg)
NFPA70E - 2000
This incident energy exposure level shall be based on the working distance of the employee’s face and chest areas from a prospective arc source for the specific task to be performed.
480V MCC
![Page 37: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/37.jpg)
Use IEEE 1584 Calculations
Preliminary IEEE 1584 work used in NFPA 70ENFPA 70E calculations limited to < 1000VIEEE 1584 equations expanded to 15,000VNFPA 70E revision will reference IEEE 1584
![Page 38: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/38.jpg)
Arc Flash Calculation Steps
Determine System Modes of OperationCalculate Bolted Fault Current at each BusCalculate Arcing Fault Current at each BusCalculate Arcing Fault Current seen by each Protective DeviceDetermine Trip Time for Each Protective Device based on Arcing Fault CurrentCalculate Incident Energy at Working DistanceCalculate Arc Flash BoundaryDetermine Required PPEGenerate Labels
![Page 39: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/39.jpg)
Find Appropriate PPE
![Page 40: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/40.jpg)
Find Appropriate PPE
![Page 41: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/41.jpg)
Generate Labels
![Page 42: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/42.jpg)
Summary
•NEC 110.16 Requires Arc Flash Hazard Labels.•NFPA 70E Requires Documented Arc Flash Calculations.•IEEE Std 1584 Defines Arc Flash Calculations.•Arc Flash Calculations Require Accurate Fault Current Values. •Arc Flash Calculations Require Over-Current Coordination Study.
![Page 43: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/43.jpg)
Summary
•Arc Flash Calculations May Require Evaluation of Multiple Operating Modes for the System.•Arc Flash Calculations Require Special Consideration For Parallel Contributions.•Arc Flash Labels may need specification of activity specific clothing levels (Line side vs Load side).
![Page 44: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/44.jpg)
Questions / Discussion
![Page 45: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/45.jpg)
•45
Managing the hazard --Administrative controls
• Operate and maintain in a way that minimizes the hazard– Site team can provide
• Site procedures• Training• Process hazards analysis for electrical
rooms• PPE program requirements
![Page 46: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/46.jpg)
•46
Site operating and maintenance procedures
• Lock and tag – General and equipment specific
• Maintenance Grounds– How? Where? When? With what? – How assure removal?
• Switching – Recognize the hazard of tying two
buses together and minimize the time
![Page 47: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/47.jpg)
•47
Training
• What training is needed?– OSHA – NFPA 70E– Company level practices – Site specific procedures– Equipment specific (Model 7700)– Use and care of PPE
![Page 48: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/48.jpg)
•48
Process hazards analysis for ECRs, Switchyards
• Get help on running analysis• What are the hazards?
– Shock, arc flash, fire, fall• How can you mitigate them?
– How call for help? -- Phone and FA available– Exit signs and lights– PPE available
• Can you reduce the likelihood? – How turn off power? -- Single lines posted – Identification and warning labels– Provision for locks where needed– Minimize obstructions, stored material
![Page 49: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/49.jpg)
•49
Engineering Controls --Design to minimize the hazard
• Reduce need for work on energized equipment
• Reduce probability of three phase faults• Reduce fault current• Reduce fault duration• Reduce impact of arc flash on people• Provide information on available fault
energy
![Page 50: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/50.jpg)
•50
Studies reveal all electrical injuries involve energized
equipment!• Most organizations prohibit hot work,
(except testing.)• Why do injuries still occur?
– Testing– Racking in breakers– Operating switches and circuit breakers– Equipment failures when no work underway– Job expanded beyond original intent - #1 reason!
![Page 51: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/51.jpg)
•51
Reduce need for work on or nearenergized equipment
• Design to enable shutdowns– Unitize loads - group by process function– Provide dual feeds to critical equipment -
controls– Money is always available for safety
• Design for easy testing and grounding• Design for remote racking and operation• Install warning labels
![Page 52: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/52.jpg)
•52
Reduce probability of three phase faults
– Metal clad vs. metal enclosed switchgear
– Insulated bus – Resistance grounded system
• Low resistance grounded - > 1 kV• High resistance grounded - 480 V, 400 V
– Adequate ground fault return path – Connection points for ground jumpers
![Page 53: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/53.jpg)
•53
Reduce fault current
• Fast current limiting fuses – Limiter fuses on 480 V feeder
breakers• Resistance grounding
– HRG on 480 V systems– LRG on 2.4 kV to 22 kV systems
![Page 54: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/54.jpg)
•54
Reduce fault duration
• Use current limiting fuses• Tighten up the coordination • Select protective devices for people
protection as well as equipment protection and reliable operation.
– Select relay settings for fast trips– Select lower rated fuses– Cut possible fault energy in half
![Page 55: ARC FLASH CALCULATIONS & LABELING …cfroundtable.org/meetings/062003/ARC_FLASH_CALCULATIONS_by... · ARC FLASH CALCULATIONS & LABELING REQUIREMENTS Presented by: Edmund Elizalde](https://reader038.fdocuments.net/reader038/viewer/2022103012/5acc0aa37f8b9a875a8c1f96/html5/thumbnails/55.jpg)
•55
Reduce impact of arc flash on people
• Avoid openings/vents in equipment doors
– Prefer door openings at the side of the door to openings in the center
• Arc resistant switchgear– Big benefit for switching
• Remote operating controls for switchgear
• Remote racking - 480 V and higher