Application Notes for AudioCodes MediaPack 11x with Avaya ...

72
KJA; Reviewed; SPOC 7/6/2012 Solution & Interoperability Test Lab Application Notes ©2012 Avaya Inc. All Rights Reserved. 1 of 72 ACMP11xCM62SM62 Avaya Solution & Interoperability Test Lab Application Notes for AudioCodes MediaPack 11x with Avaya Aura® Communication Manager and Avaya Aura® Session Manager Issue 1.0 Abstract This Application Notes document contains interoperability instructions for configuring AudioCodes MediaPack 11x with Avaya Aura® Communication Manager and Avaya Aura® Session Manager. Compliance testing was conducted to verify the interoperability. Information in these Application Notes has been obtained through DevConnect compliance testing and additional technical discussions. Testing was conducted via the DevConnect Program at the Avaya Solution and Interoperability Test Lab. NOTE: This Application Note is applicable with Avaya Aura® 6.2 which is currently in Controlled Introduction. Avaya Aura® 6.2 will be Generally Available in Summer 2012.

Transcript of Application Notes for AudioCodes MediaPack 11x with Avaya ...

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

1 of 72

ACMP11xCM62SM62

Avaya Solution & Interoperability Test Lab

Application Notes for AudioCodes MediaPack 11x with

Avaya Aura® Communication Manager and Avaya Aura®

Session Manager – Issue 1.0

Abstract

This Application Notes document contains interoperability instructions for configuring

AudioCodes MediaPack 11x with Avaya Aura® Communication Manager and Avaya Aura®

Session Manager. Compliance testing was conducted to verify the interoperability.

Information in these Application Notes has been obtained through DevConnect compliance

testing and additional technical discussions. Testing was conducted via the DevConnect

Program at the Avaya Solution and Interoperability Test Lab.

NOTE: This Application Note is applicable with Avaya Aura® 6.2 which is currently in

Controlled Introduction. Avaya Aura® 6.2 will be Generally Available in Summer 2012.

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

2 of 72

ACMP11xCM62SM62

Table of Contents

Table of Contents .................................................................................................................................. 2

1. Introduction................................................................................................................................... 4 2. General Test Approach and Test Results .................................................................................... 4

2.1. Interoperability Compliance Testing .................................................................................... 4

2.2. Test Results ............................................................................................................................ 5 2.3. Support.................................................................................................................................... 5

3. Reference Configuration .............................................................................................................. 6

4. Equipment and Software Validated............................................................................................. 7 5. Configure Avaya Aura® Communication Manager .................................................................. 8

5.1. Verify Avaya Aura® Communication Manager License .................................................... 8

5.2. Administer IP Network Region ............................................................................................. 9 5.2.1. IP Network Region for Voice and Fax Calls .............................................................. 9 5.2.2. IP Network Region for Modem Calls ....................................................................... 10

5.3. Administer IP Codec Set ..................................................................................................... 11 5.3.1. IP Codec set for Voice and Fax Calls ....................................................................... 11 5.3.2. IP Codec Set for Modem Calls .................................................................................. 12

5.4. Administer IP Node Names ................................................................................................. 13 5.5. Administer SIP Signaling Group ........................................................................................ 13

5.5.1. Signaling Group for Voice and Fax Calls ................................................................ 14

5.5.2. Signaling Group for Modem Calls ............................................................................ 15 5.6. Administer SIP Trunk Group .............................................................................................. 16

5.6.1. Trunk Group for Voice and Fax Calls ...................................................................... 16

5.6.2. Trunk Group for Modem Calls.................................................................................. 17 5.7. Administer Route Pattern .................................................................................................... 18

5.7.1. Route Pattern for Voice and Fax Calls ..................................................................... 18

5.7.2. Route Pattern for Modem Calls ................................................................................. 18 5.8. Administer Private Numbering ........................................................................................... 19 5.9. Administer AAR Analysis................................................................................................... 19

5.10. Administer ARS Analysis .............................................................................................. 20 5.11. Administer Stations ......................................................................................................... 21

6. Configure Avaya Aura® Session Manager .............................................................................. 22

6.1. Add SIP Domain .................................................................................................................. 24 6.2. Add Location ........................................................................................................................ 24 6.3. Add SIP Entity ..................................................................................................................... 26

6.4. Add Entity Link.................................................................................................................... 27 6.5. Add Time Ranges ................................................................................................................ 28 6.6. Add Routing Policy ............................................................................................................. 29

6.7. Add Dial Patterns ................................................................................................................. 31 6.8. Add User ............................................................................................................................... 33

7. Configure AudioCodes MediaPack 11x ................................................................................... 36

7.1. Verify/Upgrade Firmware Version ..................................................................................... 36

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

3 of 72

ACMP11xCM62SM62

7.2. Administer Application Settings ......................................................................................... 41 7.3. Administer Syslog Settings ................................................................................................. 42

7.4. Administer Certificates ........................................................................................................ 43 7.5. Administer DNS Setting ...................................................................................................... 44 7.6. Administer Media Security ................................................................................................. 45

7.7. Administer General Parameters .......................................................................................... 46 7.8. Administer Advanced Parameter ........................................................................................ 47 7.9. Administer Proxy and Registration..................................................................................... 47

7.10. Administer Coders .......................................................................................................... 50 7.11. Administer Coders Group Settings ................................................................................ 50 7.12. Administer Tel Profile Settings ...................................................................................... 52

7.13. Administer IP Profile Settings........................................................................................ 53 7.14. Administer EndPoint Phone Number ............................................................................ 54 7.15. Administer Hunt Group Settings .................................................................................... 55

7.16. Administering Manipulations ......................................................................................... 56 7.17. Administer IP to Trunk Group Routing ......................................................................... 57 7.18. Administer Other Parameters ......................................................................................... 58

7.19. Administer DTMF and Dialing ...................................................................................... 60 7.20. Administer Supplementary Services .............................................................................. 61 7.21. Administer FXO .............................................................................................................. 62

8. Verification Steps ....................................................................................................................... 63 8.1. Avaya Aura® Communication Manager and Avaya Aura® Session Manager............... 63

9. Conclusion .................................................................................................................................. 65

10. Additional References ......................................................................................................... 65 A. Appendix ..................................................................................................................................... 66

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

4 of 72

ACMP11xCM62SM62

1. Introduction AudioCodes MediaPack (MP) 11x Analog VoIP gateways provide voice technology to connect

analog phones, fax machines and modems (FXS) or landlines (FXO) to IP based PBX systems.

During compliance testing, AudioCodes MP-112 and AudioCodes MP-114 VoIP gateways were

used. Inherently, this also covers AudioCodes MP-118. Both AudioCodes MPs were configured

to communicate with Avaya Aura® Session Manager using SIP (Session Initiation Protocol).

2. General Test Approach and Test Results Interoperability compliance testing focused on verifying various inbound and outbound call

flows between AudioCodes MP-11x, Avaya Aura® Communication Manager and Avaya Aura®

Session Manager.

DevConnect Compliance Testing is conducted jointly by Avaya and DevConnect members. The

jointly-defined test plan focuses on exercising APIs and/or standards-based interfaces pertinent

to the interoperability of the tested products and their functionalities. DevConnect Compliance

Testing is not intended to substitute full product performance or feature testing performed by

DevConnect members, nor is it to be construed as an endorsement by Avaya of the suitability or

completeness of a DevConnect member’s solution.

2.1. Interoperability Compliance Testing

Analog lines on AudioCodes MP-11x were configured as users on Avaya Aura® Session

Manager. Each configured analog line user, registered with Session Manager. SIP TLS and

SRTP were utilized during this test effort. Following features and functionalities were covered

during compliance testing:

Incoming calls to AudioCodes MP-11x

Outgoing calls from AudioCodes MP-11x

Voice codecs G.711u, G.711A and G.729 using SRTP

Incoming and outgoing faxes using T.38

Incoming and outgoing modem calls

DTMF tone transmission with RFC2833

Calls using various Analog, H.323 and SIP endpoints supported by Avaya IP telephony

solution

Note: Configuration instructions in this document are primarily geared towards FXS lines on

AudioCodes MP-11x. Configuration for FXO lines is clearly noted, and is only necessary if

configuring FXO lines on AudioCodes MP-11x.

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

5 of 72

ACMP11xCM62SM62

2.2. Test Results

All test cases were executed and passed with the following exception/observations:

1. MWI feature: MWI for lamp wasn’t tested. However, the MWI stutter tone was tested

successfully.

2. RTCP configuration: At present, Avaya Aura® Communication Manager only supports

unencrypted RTCP. In order to disable RTCP decryption on AudioCodes MP-11x, a parameter

named RTCPEncryptionDisableRx with value of 1, needs to be configured via AdminPage.

Please note that, even though this parameter is applied, it will not be displayed in the ini file.

2.3. Support

Technical support for AudioCodes MP-11x can be obtained through the following:

Phone:

Americas: +1-732-652-1085 or 1-800-735-4588

Rest of the World: 800-44422444 or 972-3-9764343

Web:crm.audiocodes.com

E-Mail: [email protected]

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

6 of 72

ACMP11xCM62SM62

3. Reference Configuration Sample configuration that was used during compliance testing consisted of following

components:

Avaya G430 Media Gateway with Avaya S8300D Media Server running Avaya Aura®

Communication Manager

Avaya Aura® Session Manager

Avaya Aura® System Manager

Avaya IP Phones: SIP and H.323

Avaya Analog Phone

AudioCodes MP-112 and AudioCodes MP-114

Analog Fax Machine and PC with Modem

Calls and faxes were routed to/from AudioCodes MP-11x via Communication Manager and

Session Manager.

IP Phones: Avaya 96x1 and 96x0 Series

192.168.62.x

303-538-xxxx

Avaya C364TPWR

Avaya S8300 Media Server

Avaya Aura® Communication Manager 6.2

192.168.62.28

Avaya G430 Media Gateway

192.168.62.30

PSTN

OK

PHONEMESSAGE

CONTACTS MENU CALL LOG

SPEAKER MUTE VOLUME HEADSET

ABC DEF

JKL MNOGHI

1 2 3

4 5 6

TUV WXYZPQRS

7 8 9

*

[

0 #

.,@

Avaya one-X

OK

PHONEMESSAGE

CONTACTS MENU CALL LOG

VOLUME

ABC DEF

JKL MNOGHI

1 2 3

4 5 6

TUV WXYZPQRS

7 8 9

*

[

0 #

.,@

MUTESPEAKER

HEADSET

FORWARD

Avaya one-X

OK

PHONEMESSAGE

CONTACTS MENU CALL LOG

VOLUME

ABC DEF

JKL MNOGHI

1 2 3

4 5 6

TUV WXYZPQRS

7 8 9

*

[

0 #

.,@

MUTESPEAKER

HEADSET

FORWARD

Avaya one-X

OK

PHONEMESSAGE

CONTACTS MENU CALL LOG

VOLUME

ABC DEF

JKL MNOGHI

1 2 3

4 5 6

TUV WXYZPQRS

7 8 9

*

[

0 #

.,@

MUTESPEAKER

HEADSET

FORWARD

5049

25 27 29 31 33 35

32 34 3626 28 30

37 39 41 43 45 47

44 46 4838 40 42

Down/51

Base

Status

1 3 5 7 9 11 13 15 17 19 21 23

8 10 122 4 6 20 22 2414 16 18

Up/52

PWR

SpeedLink/Act

2550T

7 8 9

* 0 #

PQRS WXYZTUV

Volume

1 2 3

4 5 6

ABC DEF

MNOJKLGHI

Speaker Mute Ho ld

Redial Transfer Ring

Menu Ex it Prev Next

6408

Avaya 6211 Analog

Phone

8

1 2UID41

5

32

SID

HPProLiant

DL360 G7

8

1 2UID41

5

32

SID

HPProLiant

DL360 G7

Avaya Aura® Session Manager 6.2

192.168.62.17/18

Avaya Aura® System Manager 6.2

192.168.62.16

7 8 9

* 0 #

PQRS WXYZTUV

Volume

1 2 3

4 5 6

ABC DEF

MNOJKLGHI

Speaker Mute Ho ld

Redial Transfer Ring

Menu Ex it Prev Next

6408

7 8 9

* 0 #

PQRS WXYZTUV

Volume

1 2 3

4 5 6

ABC DEF

MNOJKLGHI

Speaker Mute Ho ld

Redial Transfer Ring

Menu Ex it Prev Next

6408

Mediant MP 112

192.168.62.12

Mediant MP 114

192.168.62.13

Fax Machine

Analog

PhoneAnalog

Phone

Fax Machine

PC with

Modem

PC with

Modem

W A N

1 LAN 10/3SERVICESCCA 10/12

USB

10/2LAN10/4

MDM

A LM

CPU

P W R

RST A SB

V1

SY

ST

EM

COMPACT FLASH

CARDIN US E

V2

V3

A UDIO

G430

ALM

TST

ACT

AVAYA

E1 /T1

MODULESIG

SO EI SM EM SI EO

ALM

TST

ACT

1 2 3 4 5 6 7 8

AVAYAMM 712

DCP

VH3

FXO

Figure 1: AudioCodes MP-112 and MP-114 with Avaya Aura® Communication Manager

and Avaya Aura® Session Manager

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

7 of 72

ACMP11xCM62SM62

4. Equipment and Software Validated The following equipment and software were used for the sample configuration provided:

Equipment/Software Release/Version

Avaya Aura® Communication Manager

running on Avaya S8300D Server

6.2 SP 02.0.823.0-19829

Avaya Aura® Session Manager 6.2 SP1

Avaya Aura® System Manager 6.2 SP1

Avaya 9630 IP Phone

Avaya 9611 IP Phone

SIP 2.6 SP7

H.323 6.2

Avaya 6211 and 6210 Analog Phone -

AudioCodes MediaPack 112 6.20A.59

AudioCodes MediaPack 114 6.20A.59

HP 1040 Fax Machine -

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

8 of 72

ACMP11xCM62SM62

5. Configure Avaya Aura® Communication Manager This section provides steps for configuring Communication Manager. All configuration for

Communication Manager is done through System Access Terminal (SAT).

5.1. Verify Avaya Aura® Communication Manager License

Use the display system-parameters customer-options command to verify options.

On Page 2, verify that there is sufficient capacity for SIP trunks by comparing Maximum

Administered SIP Trunks field with corresponding USED column field.

On Page 4, verify ISDN/PRI and Media Encryption Over IP fields are set to y.

display system-parameters customer-options Page 4 of 11

OPTIONAL FEATURES

Emergency Access to Attendant? y IP Stations? y

Enable 'dadmin' Login? y

Enhanced Conferencing? y ISDN Feature Plus? n

Enhanced EC500? y ISDN/SIP Network Call Redirection? y

Enterprise Survivable Server? n ISDN-BRI Trunks? y

Enterprise Wide Licensing? n ISDN-PRI? y

ESS Administration? y Local Survivable Processor? n

Extended Cvg/Fwd Admin? y Malicious Call Trace? y

External Device Alarm Admin? y Media Encryption Over IP? y

Five Port Networks Max Per MCC? n Mode Code for Centralized Voice Mail? n

Flexible Billing? n

Forced Entry of Account Codes? y Multifrequency Signaling? y

Global Call Classification? y Multimedia Call Handling (Basic)? y

Hospitality (Basic)? y Multimedia Call Handling (Enhanced)? y

Hospitality (G3V3 Enhancements)? y Multimedia IP SIP Trunking? y

IP Trunks? y

IP Attendant Consoles? y

display system-parameters customer-options Page 2 of 11

OPTIONAL FEATURES

IP PORT CAPACITIES USED

Maximum Administered H.323 Trunks: 4000 0

Maximum Concurrently Registered IP Stations: 2400 1

Maximum Administered Remote Office Trunks: 4000 0

Maximum Concurrently Registered Remote Office Stations: 2400 0

Maximum Concurrently Registered IP eCons: 68 0

Max Concur Registered Unauthenticated H.323 Stations: 100 0

Maximum Video Capable Stations: 2400 0

Maximum Video Capable IP Softphones: 2400 0

Maximum Administered SIP Trunks: 4000 45

Maximum Administered Ad-hoc Video Conferencing Ports: 4000 0

Maximum Number of DS1 Boards with Echo Cancellation: 80 0

Maximum TN2501 VAL Boards: 10 0

Maximum Media Gateway VAL Sources: 50 0

Maximum TN2602 Boards with 80 VoIP Channels: 128 0

Maximum TN2602 Boards with 320 VoIP Channels: 128 0

Maximum Number of Expanded Meet-me Conference Ports: 300 0

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

9 of 72

ACMP11xCM62SM62

5.2. Administer IP Network Region

Use the change ip-network-region n command to configure a network region, where n is an

existing network region.

Administer two separate ip-network-regions; one for voice and fax calls and another one for

modem calls.

5.2.1. IP Network Region for Voice and Fax Calls

Configure this network region as follows:

Set Location to 1

Set Codec Set to 1

Set Intra-region IP-IP Direct Audio to yes

Set Inter-region IP-IP Direct Audio to yes

Enter and Authoritative Domain, e.g. avaya.com

change ip-network-region 1 Page 1 of 20

IP NETWORK REGION

Region: 1

Location: 1 Authoritative Domain: avaya.com

Name:

MEDIA PARAMETERS Intra-region IP-IP Direct Audio: yes

Codec Set: 1 Inter-region IP-IP Direct Audio: yes

UDP Port Min: 2048 IP Audio Hairpinning? n

UDP Port Max: 3329

DIFFSERV/TOS PARAMETERS

Call Control PHB Value: 46

Audio PHB Value: 46

Video PHB Value: 26

802.1P/Q PARAMETERS

Call Control 802.1p Priority: 6

Audio 802.1p Priority: 6

Video 802.1p Priority: 5 AUDIO RESOURCE RESERVATION PARAMETERS

H.323 IP ENDPOINTS RSVP Enabled? n

H.323 Link Bounce Recovery? y

Idle Traffic Interval (sec): 20

Keep-Alive Interval (sec): 5

Keep-Alive Count: 5

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

10 of 72

ACMP11xCM62SM62

5.2.2. IP Network Region for Modem Calls

Configure this network region as follows, on Page 1:

Set Location to 1

Set Codec Set to 2

Set Intra-region IP-IP Direct Audio to yes

Set Inter-region IP-IP Direct Audio to yes

Enter and Authoritative Domain, e.g. avaya.com

On Page 4:

Set Codec Set to 2 for dst rgn 1

change ip-network-region 2 Page 4 of 20

Source Region: 2 Inter Network Region Connection Management I M

G A t

dst codec direct WAN-BW-limits Video Intervening Dyn A G c

rgn set WAN Units Total Norm Prio Shr Regions CAC R L e

1 2 y NoLimit n t

2 2 all

3

change ip-network-region 2 Page 1 of 20

IP NETWORK REGION

Region: 2

Location: 1 Authoritative Domain: avaya.com

Name: Modem Profile

MEDIA PARAMETERS Intra-region IP-IP Direct Audio: yes

Codec Set: 2 Inter-region IP-IP Direct Audio: yes

UDP Port Min: 2048 IP Audio Hairpinning? n

UDP Port Max: 3329

DIFFSERV/TOS PARAMETERS

Call Control PHB Value: 46

Audio PHB Value: 46

Video PHB Value: 26

802.1P/Q PARAMETERS

Call Control 802.1p Priority: 6

Audio 802.1p Priority: 6

Video 802.1p Priority: 5 AUDIO RESOURCE RESERVATION PARAMETERS

H.323 IP ENDPOINTS RSVP Enabled? n

H.323 Link Bounce Recovery? y

Idle Traffic Interval (sec): 20

Keep-Alive Interval (sec): 5

Keep-Alive Count: 5

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

11 of 72

ACMP11xCM62SM62

5.3. Administer IP Codec Set

Use the change ip-codec-set n command to configure IP codec set, where n is an existing codec

set number.

Administer two ip-codec-set; one for voice and fax calls and another one for modem calls

corresponding to ip-network-region configured in Section 5.2.1 and Section 5.2.2.

5.3.1. IP Codec set for Voice and Fax Calls

Configure this codec set as follows, on Page 1:

Set Audio Codec 1, 2 and 3 to G.711MU, G.711A, G.729AB respectively

Set Media Encryption 1 to 1-srtp-aescm128-hmac80

Note: G.711MU, G.711A and G.729AB were tested during compliance testing.

On Page 2:

Set Fax Mode to t.38-standard

change ip-codec-set 1 Page 2 of 2

IP Codec Set

Allow Direct-IP Multimedia? n

Mode Redundancy

FAX t.38-standard 0

Modem off 0

TDD/TTY US 3

Clear-channel n 0

change ip-codec-set 1 Page 1 of 2

IP Codec Set

Codec Set: 1

Audio Silence Frames Packet

Codec Suppression Per Pkt Size(ms)

1: G.711MU n 2 20

2: G.711A n 2 20

3: G.729AB n 2 20

4:

5:

6:

7:

Media Encryption

1: 1-srtp-aescm128-hmac80

2:

3:

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

12 of 72

ACMP11xCM62SM62

5.3.2. IP Codec Set for Modem Calls

For this IP Codec Set, on Page 1:

Configure this codec set as follows, on Page 1:

Set Audio Codec 1, 2 and 3 to G.711MU, G.711A, G.729AB respectively

Set Media Encryption 1 to 1-srtp-aescm128-hmac80

Note: G.711MU, G.711A and G.729AB were tested during compliance testing.

On Page 2:

Set Fax Mode to off

Set Modem Mode to off

change ip-codec-set 2 Page 2 of 2

IP Codec Set

Allow Direct-IP Multimedia? n

Mode Redundancy

FAX off 0

Modem off 0

TDD/TTY US 3

Clear-channel n 0

change ip-codec-set 2 Page 1 of 2

IP Codec Set

Codec Set: 2

Audio Silence Frames Packet

Codec Suppression Per Pkt Size(ms)

1: G.711MU n 2 20

2: G.711A n 2 20

3: G.729AB n 2 20

4:

5:

6:

7:

Media Encryption

1: 1-srtp-aescm128-hmac80

2:

3:

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

13 of 72

ACMP11xCM62SM62

5.4. Administer IP Node Names

Use the change node-names ip command to add an entry for Session Manager. For compliance

testing, sm and 192.168.62.18 entry was added.

5.5. Administer SIP Signaling Group

Use the add signaling-group n command to add a new signaling group, where n is an available

signaling group number.

Add two signaling groups; one for voice and fax calls and another one for modem calls

corresponding to ip-network-region configured in Section 5.2.1 and Section 5.2.2.

change node-names ip Page 1 of 2

IP NODE NAMES

Name IP Address

default 0.0.0.0

msgsrvr 192.168.62.28

procr 192.168.62.28

procr6 ::

sm 192.168.62.18

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

14 of 72

ACMP11xCM62SM62

5.5.1. Signaling Group for Voice and Fax Calls

Configure this signaling group as follows:

Set Group Type to sip

Set Near-end Node Name to procr

Set Far-end Node Name to the configured Session Manager in Section 5.4, i.e. sm

Set Far-end Network region to the configured region in Section 5.2.1, i.e. 1

Enter a Far-end Domain, e.g. avaya.com

add signaling-group 1 Page 1 of 2

SIGNALING GROUP

Group Number: 1 Group Type: sip

IMS Enabled? n Transport Method: tls

Q-SIP? n

IP Video? n Enforce SIPS URI for SRTP? y

Peer Detection Enabled? y Peer Server: Others

Near-end Node Name: procr Far-end Node Name: sm

Near-end Listen Port: 5061 Far-end Listen Port: 5061

Far-end Network Region: 1

Far-end Domain: avaya.com

Bypass If IP Threshold Exceeded? n

Incoming Dialog Loopbacks: eliminate RFC 3389 Comfort Noise? n

DTMF over IP: rtp-payload Direct IP-IP Audio Connections? y

Session Establishment Timer(min): 3 IP Audio Hairpinning? n

Enable Layer 3 Test? y Initial IP-IP Direct Media? n

H.323 Station Outgoing Direct Media? n Alternate Route Timer(sec): 6

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

15 of 72

ACMP11xCM62SM62

5.5.2. Signaling Group for Modem Calls

Configure this signaling group as follows:

Set Group Type to sip

Set Near-end Node Name to procr

Set Far-end Node Name to the configured Session Manager in Section 5.4, i.e. sm

Set Far-end Network region to the configured region in Section 5.2.2, i.e. 2

Enter a Far-end Domain, e.g. avaya.com

Note: Signaling Group, Trunk Group and Route Pattern for PSTN calls via PRI was pre-

configured and is not shown in this document.

add signaling-group 2 Page 1 of 2

SIGNALING GROUP

Group Number: 2 Group Type: sip

IMS Enabled? n Transport Method: tls

Q-SIP? n

IP Video? n Enforce SIPS URI for SRTP? y

Peer Detection Enabled? y Peer Server: Others

Near-end Node Name: procr Far-end Node Name: sm

Near-end Listen Port: 5061 Far-end Listen Port: 5061

Far-end Network Region: 2

Far-end Domain: avaya.com

Bypass If IP Threshold Exceeded? n

Incoming Dialog Loopbacks: eliminate RFC 3389 Comfort Noise? n

DTMF over IP: rtp-payload Direct IP-IP Audio Connections? y

Session Establishment Timer(min): 3 IP Audio Hairpinning? n

Enable Layer 3 Test? y Initial IP-IP Direct Media? n

H.323 Station Outgoing Direct Media? n Alternate Route Timer(sec): 6

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

16 of 72

ACMP11xCM62SM62

5.6. Administer SIP Trunk Group

Use the add trunk-group n command to add a trunk group, where n is an available trunk group

number.

Add two trunk groups; one for voice and fax calls and another one for modem calls

corresponding to signaling group configured in Section 5.5.1 and Section 5.5.2.

5.6.1. Trunk Group for Voice and Fax Calls

Configure this trunk group as follows, on Page 1:

Set Group Type to sip

Enter a Group Name, e.g. Voice and Fax Calls

Enter a valid TAC, e.g. *001

Set Service Type to tie

Enter Signaling Group value to the signaling group configured in Section 5.5.1, i.e. 1

Enter a desired number in Number of Member field

On Page 3:

Set Number Format to private

add trunk-group 1 Page 3 of 21

TRUNK FEATURES

ACA Assignment? n Measured: none

Maintenance Tests? y

Numbering Format: private

UUI Treatment: service-provider

Replace Restricted Numbers? n

Replace Unavailable Numbers? n

add trunk-group 1 Page 1 of 21

TRUNK GROUP

Group Number: 1 Group Type: sip CDR Reports: y

Group Name: Voice and Fax Calls COR: 1 TN: 1 TAC: *001

Direction: two-way Outgoing Display? n

Dial Access? n Night Service:

Queue Length: 0

Service Type: tie Auth Code? n

Member Assignment Method: auto

Signaling Group: 1

Number of Members: 25

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

17 of 72

ACMP11xCM62SM62

5.6.2. Trunk Group for Modem Calls

Configure this trunk group as follows, on Page 1:

Set Group Type to sip

Enter a Group Name, e.g. Modem Calls

Enter a valid TAC, e.g. *002

Set Service Type to tie

Enter Signaling Group value to the signaling group configured in Section 5.5.2, i.e. 2

Enter a desired number in Number of Member field

On Page 3:

Set Number Format to private

add trunk-group 2 Page 3 of 21

TRUNK FEATURES

ACA Assignment? n Measured: none

Maintenance Tests? y

Numbering Format: private

UUI Treatment: service-provider

Replace Restricted Numbers? n

Replace Unavailable Numbers? n

add trunk-group 2 Page 1 of 21

TRUNK GROUP

Group Number: 2 Group Type: sip CDR Reports: y

Group Name: Modem Calls COR: 1 TN: 1 TAC: *001

Direction: two-way Outgoing Display? n

Dial Access? n Night Service:

Queue Length: 0

Service Type: tie Auth Code? n

Member Assignment Method: auto

Signaling Group: 2

Number of Members: 25

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

18 of 72

ACMP11xCM62SM62

5.7. Administer Route Pattern

Use the change route-pattern n command to configure a route pattern, where n is an available

route patterns.

Configure two route patterns; one for voice and fax calls and another for Modem calls.

5.7.1. Route Pattern for Voice and Fax Calls

Configure this route pattern as follows:

Type a name in Pattern Name field

For line 1, set Grp No to the trunk group configured in Section 5.6.1, i.e. 1

For line 1, set FRL to 0

5.7.2. Route Pattern for Modem Calls

Configure this route pattern as follows:

Type a name in Pattern Name field

For line 1, set Grp No to the trunk group configured in Section 5.6.2, i.e. 2

For line 1, set FRL to 0

change route-pattern 2 Page 1 of 3

Pattern Number: 2 Pattern Name: Modem

SCCAN? n Secure SIP? n

Grp FRL NPA Pfx Hop Toll No. Inserted DCS/ IXC

No Mrk Lmt List Del Digits QSIG

Dgts Intw

1: 2 0 n user

2: n user

change route-pattern 1 Page 1 of 3

Pattern Number: 1 Pattern Name: Voice and Fax

SCCAN? n Secure SIP? n

Grp FRL NPA Pfx Hop Toll No. Inserted DCS/ IXC

No Mrk Lmt List Del Digits QSIG

Dgts Intw

1: 1 0 n user

2: n user

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

19 of 72

ACMP11xCM62SM62

5.8. Administer Private Numbering

Use the change private-numbering 1 command to define the calling party number to send to

Session Manager.

Configure private numbering as follows:

Add entries for trunk group configured in Section 5.6

Note: For compliance testing, 5-digit extensions beginning with 5 routed over trunk groups 1

and 2 resulted in a 5-digit calling party number.

5.9. Administer AAR Analysis

Use the change aar analysis n command to configure routing for extensions starting with n.

Add two entries, one for voice and fax calls and another one for modem calls. For compliance

testing, extensions starting with 540 were used for voice and fax calls and 541 were used for

modem calls.

Set Dialed String to starting digits of extensions that will be used, e.g. 540

Set Min and Max to 5 for 5 digit extensions

Set Route Pattern to pattern configured in Section 5.7, i.e. 1

Set Call Type to aar

Note: An entry to dial plan will need to be added for extension range used in this step.

change aar analysis 5 Page 1 of 2

AAR DIGIT ANALYSIS TABLE

Location: all Percent Full: 2

Dialed Total Route Call Node ANI

String Min Max Pattern Type Num Reqd

540 5 5 1 aar n

541 5 5 2 aar n

54999 5 5 99 aar n

6 7 7 254 aar n

7 7 7 254 aar n

8 7 7 254 aar n

9 7 7 254 aar n

change private-numbering 1 Page 1 of 2

NUMBERING - PRIVATE FORMAT

Ext Ext Trk Private Total

Len Code Grp(s) Prefix Len

5 5 1 5 Total Administered: 1

5 5 2 5 Maximum Entries: 540

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

20 of 72

ACMP11xCM62SM62

5.10. Administer ARS Analysis

Use the change ars analysis n command to configure routing for calling to PSTN, where n is an

NPA or starting digit of PSTN numbers. This configuration is used to route PSTN calls to an

FXO line on AudioCodes MP-11x. For compliance testing, PSTN calls were placed to phones

with NPA of 303.

Set Dialed String to 303

Set Total Min and Total Max to 10

Set Route Pattern to pattern configured in Section 5.7, i.e. 1

Set Call Type to hnpa

Note: This administration is only required if FXO line is being configured on AudioCodes MP-

11x.

change ars analysis 3 Page 1 of 2

ARS DIGIT ANALYSIS TABLE

Location: all Percent Full: 2

Dialed Total Route Call Node ANI

String Min Max Pattern Type Num Reqd

303 10 10 1 hnpa n

4 7 7 2 hnpa n

411 3 3 deny svcl n

555 7 7 deny hnpa n

6 7 7 2 hnpa n

611 3 3 1 svcl n

7 7 7 2 hnpa n

8 7 7 2 hnpa n

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

21 of 72

ACMP11xCM62SM62

5.11. Administer Stations

Administration of Avaya Stations/Extensions in Communication Manager and Session Manager

is not shown in this document. Please refer to document [1] and/or [2] in reference section of this

document.

Note: Please ensure that SRTP encryption is turned on for SIP stations connected to Session

Manager. SRTP encryption can be turned on by modifying 46xxsettings.txt file; change

MEDIAENCRYTION parameter to 1,9; 1 is encryption of aescm128-hmac80 and 9 is none.

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

22 of 72

ACMP11xCM62SM62

6. Configure Avaya Aura® Session Manager Configuration of Avaya Aura® Session Manager is performed via Avaya Aura® System

Manager. Access the System Manager Administration web interface by entering https://<ip-

address>/SMGR URL in a web browser, where <ip-address> is the IP address of System

Manager.

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

23 of 72

ACMP11xCM62SM62

Log in using appropriate credentials.

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

24 of 72

ACMP11xCM62SM62

6.1. Add SIP Domain

Navigate to Home Elements Routing Domains, click on New button (not shown) and

configure as follows:

In Name field type in a domain (authoritative domain used in Section 5) i.e. avaya.com

Set Type to sip

Click Commit to save changes.

6.2. Add Location

Navigate to Home Elements Routing Location, click on New button (not shown) and

configure as follows:

Under General:

Type in a descriptive Name

Under Location Pattern click on New (not shown):

Type in an IP Address Pattern, e.g. 192.168.62.*

Click Commit to save changes. Screen shot shown on next page.

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

25 of 72

ACMP11xCM62SM62

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

26 of 72

ACMP11xCM62SM62

6.3. Add SIP Entity

Add Communication Manager as a SIP Entity. Navigate to Home Elements Routing

SIP Entities, click on New (no shown) and configure as follows:

Type in a descriptive name in Name field

Type in the IP address or FQDN of Communication Manager in FQDN or IP Address

field.

Set Type to CM

Set Location to the location configured in Section 6.2

Click Commit to save changes.

Note: It is assumed that SIP Entity for Session Manager has been already configured.

If administering FXO line on AudioCodes MP-11x, add another SIP Entity (not shown):

Type in a descriptive name in Name field

Type in the IP address or FQDN of AudioCodes MP-11x in FQDN or IP Address field.

Set Type to SIP Trunk

Set Location to the location configured in Section 6.2

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

27 of 72

ACMP11xCM62SM62

6.4. Add Entity Link

Navigate to Home Elements Routing Entity Links, click on New (not shown) and

configure as follows:

Type in a descriptive name in Name field

Set SIP Entity 1 to the name of Session Manager SIP Entity

Set SIP Entity 2 to Communication Manager SIP Entity configured in Section 6.3

Click Commit to save changes.

If administering FXO line on AudioCodes MP-11x, add another Entity Link (not shown):

Type in a descriptive name in Name field

Set SIP Entity 1 to the name of Session Manager SIP Entity

Set SIP Entity 2 to AudioCodes MP-11x SIP Entity configured in Section 6.3.

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

28 of 72

ACMP11xCM62SM62

6.5. Add Time Ranges

Navigate to Home Elements Routing Time Ranges, click on New (now shown) and

configure as follows:

Type in a descriptive name in Name field

Click Commit to save changes.

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

29 of 72

ACMP11xCM62SM62

6.6. Add Routing Policy

Navigate to Home Elements Routing Routing Policies, click on New (not shown) and

configure as follows:

Type in a descriptive name in Name field

Under SIP Entity as Destination, click on Select (not shown):

o Select Communication Manager SIP entity added in Section 6.3

Under Time of Day, click on Add (not shown):

o Select time range added in previous step

Click Commit to save changes.

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

30 of 72

ACMP11xCM62SM62

If administering FXO line on AudioCodes MP-11x, add another Routing Policy (not shown):

Type in a descriptive name in Name field

Under SIP Entity as Destination, click on Select (not shown):

o Select AudioCodes MP-11x SIP entity added in Section 6.3

Under Time of Day, click on Add (not shown):

o Select time range added in previous step

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

31 of 72

ACMP11xCM62SM62

6.7. Add Dial Patterns

Navigate to Home Elements Routing Dial Patterns, click on New (not shown) and

configure as follows:

Under General:

Set Pattern to prefix of dialed number

Set Min to minimum length of dialed number

Set Max to maximum length of dialed number

Set Domain to domain configured on Section 6.1

Under Originating Locations and Routing Policies:

Click Add and select originating location and Communication Manager routing policy as

configured in Section 6.2 and Section 6.6 respectively

Click Commit to save changes.

Note: For Compliance testing, dialed number of 5xxxx were used. Thus, pattern, min and max

values were all set to 5.

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

32 of 72

ACMP11xCM62SM62

If administering FXO line on AudioCodes MP-11x, add another Dial Pattern (not shown):

Under General:

Set Pattern to prefix of dialed number

Set Min to minimum length of dialed number

Set Max to maximum length of dialed number

Set Domain to domain configured on Section 6.1

Under Originating Locations and Routing Policies:

Click Add and select originating location and AudioCodes MP-11x routing policy as

configured in Section 6.2 and Section 6.6 respectively

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

33 of 72

ACMP11xCM62SM62

6.8. Add User

For each analog line on AudioCodes MP-11x, a user needs to be added on Session Manager.

Information in this section will be used by AudioCodes MP-11x for registering to Session

Manager.

Navigate to Home Users User Management Manage User, click on New (not shown)

and configure as follows:

Under Identity tab:

Type in Last Name and First Name

In Login Name field type in <extension>@<domain>. <Extension> is an extension

which will be configured on AudioCodes MP-11x to receive and make calls. <domain>

is as configured in Section 6.1

Type in a desired Password and Confirm Password

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

34 of 72

ACMP11xCM62SM62

Under Communication Profile tab:

Under Communication Profile type in desired Communication Profile Password and

Confirm Password.

Under Communication Address, click on New (now shown)

o Type in <extension> in the text field, select domain configured in Section 6.1 for

Fully Qualified Address. <Extension> is the same extension configured for login

name under Identity tab. Click on Add. Please note that AudioCodes MP-11x will

use this information has login name to register to Session Manager.

Check the Session Manager Profile box:

o Set Primary Session Manager to Session Manager. i.e. SM_Public.

o Set Origination Application Sequence and Termination Application Sequence

to Communication Manager. Please note that configuration for Application

Sequence is not shown in this document. Please refer to document [2] in reference

section of this document for further details.

o Set Home Location.

Check the CM Endpoint Profile box:

o Set System to Communication Manager.

o Set Profile Type to Endpoint.

o Type in extension number used in this section for Extension field.

o Set Template to DEFAULT_9640SIP_CM_6_2

o Set Security Code to a desired value. Please note that AudioCodes MP-11x will

use this security code as password to register to Session Manager.

Click Commit to save changes.

Screen capture continued on next page.

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

35 of 72

ACMP11xCM62SM62

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

36 of 72

ACMP11xCM62SM62

7. Configure AudioCodes MediaPack 11x Administration for AudioCodes MP-11x series is done via administrative console. Type in

http://<ip-address> URL in a web browser, where <ip-address> is the IP Address of AudioCodes

MP-11x.

Note: It is assumed that AudioCodes MP-11x has been assigned an IP address. If AudioCodes

MP-11x is using the factory defaults, change the IP address of your computer to 10.1.10.1 with a

subnet of 255.255.0.0 so that it can communicate with the device using its factory default IP

address of 10.1.10.10. For further details, please see document [5] in additional references

section of this document.

Note: Configuration mentioned in the section is performed for AudioCodes MP-114. A sample

.ini file generated after configuring AudioCodes MP-114 can be found in Appendix A.

AudioCodes MP-11x series devices’ administrative consoles are similar to the one that is

configured on this section.

Log on to administrative console using appropriate credentials.

7.1. Verify/Upgrade Firmware Version

Once logged in, the firmware version can be found on the Home page under General

Information box. The firmware version should be 6.20A.059 or higher.

Please note that during the compliance testing, the version of AudioCodes MP-11x used, was

6.20A.059.

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

37 of 72

ACMP11xCM62SM62

If the version is different, contact AudioCodes support and get the correct version firmware.

Once it has been obtained:

Click on the drop down menu as shown and select Software Upgrade Wizard

Click on Start Software Upgrade

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

38 of 72

ACMP11xCM62SM62

A pop-up window will open, click on CMP File. Select Choose File and locate the

firmware (not shown)

Click on Send File

Once the file is loaded on the device, following text will be displayed

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

39 of 72

ACMP11xCM62SM62

Click Reset to upgrade the device.

Once the upgrade is complete, click on End Process

Verify the version once the upgrade process is complete as mentioned earlier in this

section

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

40 of 72

ACMP11xCM62SM62

To ensure that the configuration is default, in a case where the box was previously used,

upload an ini file that is empty:

Open Notepad on a Windows machine, Save as empty.ini

From AudioCodes MP-11x console, click on the drop down menu Device Actions in the

top center of the screen, and select Load Configuration File (not shown)

Click on Choose File and navigate to the location of recently created empty.ini and

select it.

Click on Send File

Click OK to confirm (not shown)

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

41 of 72

ACMP11xCM62SM62

7.2. Administer Application Settings

All administration is done via the left pane on administrative console.

Click on Full as shown on the screen shot

Expand System folder and click on Application Settings

Fill in NTP Server IP Address

Fill in NTP UTC Offset for the local time zone

Under DHCP Setting, ensure that Enable DHCP is set to Disable (not shown)

Note: For compliance testing a NTP server provided by pool.ntp.org was used and an offset of -6

was used.

Click on Submit to save changes (not shown).

Click on Regional Setting on the left pane. It should now display the correct local time

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

42 of 72

ACMP11xCM62SM62

7.3. Administer Syslog Settings

Navigate to System Syslog Settings

Set Enable Syslog to Enable

For Syslog Server IP Address, type in the IP address of a workstation that is running a

syslog application, e.g. ACSyslog

Set Debug Level to 5

Under Activity Types to Report via ‘Activity Log’ Messages, check all boxes

Please note that, Syslog does not need to be enabled to successfully interoperate Session

Manager with AudioCodes MP-11x. However, AudioCodes recommends to it to be turned on for

troubleshooting purposes. Turning Syslog on does not impact performance of AudioCodes MP-

11x.

Click Submit to save changes (not shown).

Reset the device to save changes to flash memory of AudioCodes MP-11x.

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

43 of 72

ACMP11xCM62SM62

7.4. Administer Certificates

In order for TLS/SRTP to work, three certificates are needed:

1. Private Key Certificate

2. Trusted Root Certificate

3. Server Certificate

Please note that without these certificates, TLS/SRTP will not work. To obtain these certificates,

please contact Avaya Sales or Avaya Business Partner.

Once certificates have been obtained, configure as follows:

Navigate to System Certificates on the left pane.

For each certificate, click on Choose File and locate the file. Click on Send File.

Following screen shot only shows Private Key certificate. Once Private Key certificate is

uploaded successfully, repeat this step for Trusted Root Certificate and Server Certificate.

If the certificate is uploaded successfully, following message will be displayed at the

bottom of the screen.

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

44 of 72

ACMP11xCM62SM62

7.5. Administer DNS Setting

On the left pane, navigate to VoIP Network DNS DNS Setting. If DNS Servers are

used, type in their IP Address. For compliance testing, DNS servers were not used. Instead, DNS

entries were manually entered in Internal DNS table.

If DNS servers are not available, DNS entries can be entered manually by navigating to VoIP

Network DNS Internal DNS Table.

Fill in the information for Domain and First IP Address

Click Submit to save changes (not shown).

Note: It is good practice to click Burn on top of the page, after each change is made, to burn

changes into flash memory of AudioCodes MP-11x.

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

45 of 72

ACMP11xCM62SM62

7.6. Administer Media Security

On the left pane, navigate to VoIP Media Media Security

Set Media Security to Enable

Set Media Security Behavior to Mandatory

Set Encryption on Transmitted RTCP Packets to Inactive

Click on SRTP offered Suite, uncheck all boxes except CIPHER SUITES AES CM

128 HMAC SHA1 80

Click Submit to save changes (not shown).

Note: This change requires a reset of AudioCodes MP-11x. Please burn the changes and reset the

device before performing any further configuration.

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

46 of 72

ACMP11xCM62SM62

7.7. Administer General Parameters

On the left pane, navigate to VoIP SIP Definitions General Parameters

Set Enable Early Media to Enable

Set Fax Signaling Method to T.38 Relay

Set SIP Transport Type to TLS

Set Enable SIPS to Enable

Set SIP Destination Port to 5061

Click Submit to save changes (not shown).

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

47 of 72

ACMP11xCM62SM62

7.8. Administer Advanced Parameter

On the left pane, navigate to VoIP SIP Definitions Advanced Parameter

Set Disconnect on Broken Connection to No

Set CDR Server IP Address to the same ip address configured for syslog ip address

Set CDR Report Level to Start & End & Connect Call

Click Submit to save changes (not shown).

7.9. Administer Proxy and Registration

On the left name, navigate to VoIP SIP Definitions Proxy & Registration

Set Use Default Proxy to Yes

Set Always Use Proxy to Enable

Set Redundant Routing Mode to Disable

Set Enable Registration to Enable

Set Registrar Name to the domain name that will be used for registration, e.g.

avaya.com

Set Registrar Transport Type to TLS

Fill in Registration Time to a desired value, in seconds

Set Re-register On INVITE Failure to Enable

Set ReRegister On Connection Failure to Enable

Fill in Gateway Name, e.g. avaya.com

Set Password to the password configured in Section 6.8 under Communication Profile

tab.

Click Submit to save changes (not shown). Screen capture below.

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

48 of 72

ACMP11xCM62SM62

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

49 of 72

ACMP11xCM62SM62

On the same page, click on the Arrow icon, , next to Proxy Set Table (not shown)

Type in the Proxy Address, e.g. avaya.com:5061

Set Transport Type to TLS

Set Enable Proxy Keep Alive to Using Options

Set Proxy Keep Alive Time to a desired value, in seconds.

Click Submit to save changes.

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

50 of 72

ACMP11xCM62SM62

7.10. Administer Coders

On the left pane, navigate to VoIP Coders and Profiles Coders

Set coders as shown in the screen capture below

Note: Default value of Packetization Time is 20. When adding a coder, verify that

Packetization Time value is 20. Also, Packetization Time must match Packet Size(ms) value

in Section 5.3.1, 20.

7.11. Administer Coders Group Settings

For Modem calls, a profile will need to be created. For Voice and Fax calls, global profile will be

used.

On the left pane, navigate to VoIP Coders and Profiles Coders Group Settings

Set Coder Group ID to 1

Configure coders as shown in the screen capture below

Note: Default value of Packetization Time is 20. When adding a coder, verify that

Packetization Time value is 20. Also, Packetization Time must match Packet Size(ms) value

in Section 5.3.1, 20.

Click Submit to save changes (not shown).

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

51 of 72

ACMP11xCM62SM62

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

52 of 72

ACMP11xCM62SM62

7.12. Administer Tel Profile Settings

For Modem calls, a profile will need to be created. For Voice and Fax calls, global profile will be

used.

On the left pane, navigate to VoIP Coders and Profiles Tel Profile Settings

Set Profile ID to 1

Type in a desired Profile Name

Set Fax Signaling Method to No Fax

Set Dialing Mode to One Stage

Set Coder Group to the group configured in previous step, i.e. Coder Group 1

Click Submit to save changes.

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

53 of 72

ACMP11xCM62SM62

7.13. Administer IP Profile Settings

For Modem calls, a profile will need to be created. For Voice and Fax calls, global profile will be

used.

On the left pane, navigate to VoIP Coders and Profiles IP Profile Settings

Set Profile ID to 1

Type in desired Profile Name

Set Dynamic Jitter Buffer Minimum Delay to 20

Set Dynamic Jitter Buffer Optimization Factor to 13

Set Fax Signaling Method to No Fax

Set Media Security Behavior to Mandatory

Click Submit to save changes

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

54 of 72

ACMP11xCM62SM62

7.14. Administer EndPoint Phone Number

On the left pane, navigate to VoIP GW and IP to IP Hunt Group EndPoint Phone

Number, for each line

Set Channel to a channel number, e.g. 1

Set Phone Number to the extension configured is Session Manager, e.g. 54150

Set Hunt Group ID to a hunt group value (configured in next section), e.g. 1

Set Tel Profile ID to 0 for global (voice and fax) and 1 for modem

Click Submit to save changes (not shown).

Note: All phone numbers entered in this screen must be configured as users in Session Manager.

Note: Channel 1 and 2 are FXS lines, Channel 3 is FXO line. When SRTP is configured,

AudioCodes MP-11x DSP capacity is reduced by 25%. In this case, there are 4 analog ports on

AudioCodes MP-114, but since SRTP is enabled, only 3 ports can be used.

Click on Register at the bottom of the screen (not shown) to register with Session Manager.

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

55 of 72

ACMP11xCM62SM62

7.15. Administer Hunt Group Settings

On the left pane, navigate to VoIP GW and IP to IP Hunt Group Hunt Group

Settings

Set Hunt Group ID to the ID used in previous step, i.e. 1.

Set Channel Select Mode to By Dest Phone Number for FXS ports. If configuring FXO

port, set it to Cyclic Ascending.

Set Registration Mode to Per Endpoint.

Click Submit to save changes (not shown).

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

56 of 72

ACMP11xCM62SM62

7.16. Administering Manipulations

This configuration is only requirement if an FXO line is being configured and if the FXO line is

connected to another PBX, which requires 91 prefix for PSTN routing.

On the left pane, navigate to VoIP GW and IP to IP Manipulations Dest Number IP

-> Tel

Add an index, e.g. 1, and click on Add (not shown)

Under Destination Prefix, type in xxxxxxxxxx#

For Source Prefix and Source IP Address, type in *

Under Prefix to Add, type in 91

Click Submit to save changes.

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

57 of 72

ACMP11xCM62SM62

7.17. Administer IP to Trunk Group Routing

On the left pane, navigate to VoIP GW and IP to IP Routing IP to Trunk Group

Routing, for each extension

Set Dest. Host Prefix, Source Host Prefix, Source Phone Prefix and Source IP

Address to *

Set Dest. Phone Prefix to the prefix of extensions, e.g. 54xxx.

Set Hunt Group ID to ID configured in previous step, i.e. 1.

Set IP Profile ID to 0 for Voice and Fax calls and 1 for Modem calls. For more

information please refer to document [4] in additional references section of this

document.

Click Submit to save changes (not shown).

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

58 of 72

ACMP11xCM62SM62

7.18. Administer Other Parameters

Type in http://<ip-address>/AdminPage URL in a web browser, where <ip-address> in the ip

address of AudioCodes MP-11x, click on ini Parameters on the left pane.

In the table below type in each parameter and associated value, click Apply New Value

Verify the output shows updated value

Parameter Name Value

HTTPSCIPHERSTRING ALL:!ADH

ENABLEDHCPLEASERENEWAL 0

DHCPENABLE 0

RTCPENCRYPTIONDISABLERX 1

MAXCALLDURATION 1440

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

59 of 72

ACMP11xCM62SM62

Screen capture below shows output for applying new value of HTTPSCIPHERSTRING.

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

60 of 72

ACMP11xCM62SM62

7.19. Administer DTMF and Dialing

On the left pane, navigate to VoIP GW and IP to IP DTMF and Supplementary

DTMF & Dialing

Set Max Digits In Phone Num to 19.

Set Digit Mapping Rules to prefix of extensions and PSTN, e.g. 54xxx|91xxxxxxxxx

will allow for routing to any phone number starting with 54 and 5 digits long and phone

number starting with 91 and 12 digits long. Please refer to document [4] in additional

reference section of this document for further details.

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

61 of 72

ACMP11xCM62SM62

7.20. Administer Supplementary Services

On the left pane, navigate to VoIP GW and IP to IP DTMF and Dialing

Supplementary Services

Under Message Waiting Indication (MWI) Parameters:

o Set Enable Caller ID to Enable

o Set Enable MWI to Enable

o Set MWI Analog Lamp to Enable

o Set MWI Display to Enable

o Set Subscribe to MWI to Yes

o For MWI Server IP Address, type in Session Manager’s IP Address

o Set MWI Server Transport Type to TLS

Click Submit to save changes

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

62 of 72

ACMP11xCM62SM62

7.21. Administer FXO

On the left pane, navigate to VoIP GW and IP to IP Analog Gateway FXO Settings

Set Dialing Mode to One Stage

Click Submit to save changes. Also, click Burn to save changes to the flash memory of

AudioCodes MP-11x.

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

63 of 72

ACMP11xCM62SM62

8. Verification Steps

8.1. Avaya Aura® Communication Manager and Avaya Aura® Session Manager

Verify SIP trunks to Session Manager are in service via SAT, using status trunk n,

where n is the number of the trunk configured in Section 5.6. Service State column

should show in-service/idle.

status trunk 1 Page 1

TRUNK GROUP STATUS

Member Port Service State Mtce Connected Ports

Busy

0001/001 T00001 in-service/idle no

0001/002 T00002 in-service/idle no

0001/003 T00003 in-service/idle no

0001/004 T00004 in-service/idle no

0001/005 T00005 in-service/idle no

0001/006 T00006 in-service/idle no

0001/007 T00007 in-service/idle no

0001/008 T00008 in-service/idle no

0001/009 T00009 in-service/idle no

0001/010 T00010 in-service/idle no

0001/011 T00011 in-service/idle no

0001/012 T00012 in-service/idle no

0001/013 T00013 in-service/idle no

0001/014 T00014 in-service/idle no

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

64 of 72

ACMP11xCM62SM62

Verify registration from AudioCodes MP-11x to Session Manager via System Manager

console, http://<ip-address/

Navigate to Home Session Manager System Status User Registration

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

65 of 72

ACMP11xCM62SM62

9. Conclusion These Application Notes describe the configuration steps required for AudioCodes MP-11x to

successfully interoperate with Avaya Aura® Communication Manager and Avaya Aura®

Session Manager. All feature and serviceability test cases completed and pass with

observations/exceptions noted in Section 2.2

10. Additional References This section references the product documentation relevant for these Application Notes.

[1] Administering Avaya Aura® Communication Manager, Document 03-300509, Release

6.2, Issue 7.0, February 2012

[2] Administering Avaya Aura® Session Manager, Document 03-603324, Release 6.2,

February 2012

[3] AudioCodes Transport Layer Security Note, Document LTRT-31600, January 2012

[4] MP-11x and MP-124 SIP User’s Manual, Version 6.2, Document LTRT-65414,

November 2010

[5] MP-11x and MP-124 SIP Installation Manual, Version 6.2, Document LTRT-59812,

September 2010

[6] SIP CPE Release Notes, Version 6.2, Document LTRT-26903

[7] Configuring Syslog Technical Note, Version 6.2, Document LTRT-28600

[8] Errata-Addendum for SIP CPE Documentation, Version 6.2, Document LTRT-29101

[9] Restoring Factory Defaults Technical Note, Version 6.2, Document LTRT-30300

[10] BootP Technical Note, Version 6.2, Document LTRT-30500

[11] Customer Case Reporting Procedures, Document LTRT-36502

[12] SIP CPE Product Reference Manual, Version 6.2, LTRT-52307

[13] CPE SIP Troubleshooting Guide, Document LTRT-57601

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

66 of 72

ACMP11xCM62SM62

A. Appendix AudioCodes MP-114 .ini file generated after following the instruction is as follows: Please use it

only for reference purposes.

Note: Please note that password for registration will need to be changed if this ini file is loaded

on an AudioCodes MP-11x device.

;**************

;** Ini File **

;**************

;Board: MP-114 FXS_FXO

;Serial Number: 2478413

;Slot Number: 1

;Software Version: 6.20A.059

;DSP Software Version: 204IM => 620.10

;Board IP Address: 192.168.62.13

;Board Subnet Mask: 255.255.255.128

;Board Default Gateway: 192.168.62.1

;Ram size: 32M Flash size: 8M

`;Num of DSP Cores: 1 Num DSP Channels: 3

;Profile: NONE

;License Key limits aren't active full features capabilities are available !;

;----------------------------------------------

[SYSTEM Params]

SyslogServerIP = 192.168.62.24

EnableSyslog = 1

NTPServerIP = 75.144.11.42

NTPServerUTCOffset = -21600

ENABLEPARAMETERSMONITORING = 1

ActivityListToLog = 'pvc', 'afl', 'dr', 'fb', 'swu', 'ard', 'naa', 'spc',

'll'

[BSP Params]

PCMLawSelect = 3

RoutingTableHopsCountColumn = 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,

0, 0, 0, 0, 0, 0, 0, 0, 0

[Analog Params]

FXSLoopCharacteristicsFilename = 'MP11x-02-1-FXS_16KHZ.dat'

[ControlProtocols Params]

AdminStateLockControl = 0

[MGCP Params]

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

67 of 72

ACMP11xCM62SM62

[MEGACO Params]

EP_Num_0 = 0

EP_Num_1 = 1

EP_Num_2 = 1

EP_Num_3 = 0

EP_Num_4 = 0

DIGITMAPPING = '54xxx|91xxxxxxxxxx'

[Voice Engine Params]

CallProgressTonesFilename = 'usa_tones_13.dat'

ENABLEMEDIASECURITY = 1

RTCPEncryptionDisableTx = 1

RTCPEncryptionDisableRx = 1

[WEB Params]

LogoWidth = '145'

HTTPSCipherString = 'ALL:!ADH'

[SIP Params]

MAXDIGITS = 19

REGISTRATIONTIME = 600

ISPROXYUSED = 1

ISREGISTERNEEDED = 1

SIPDESTINATIONPORT = 5061

ISTWOSTAGEDIAL = 0

CDRREPORTLEVEL = 4

GWDEBUGLEVEL = 5

ENABLEEARLYMEDIA = 1

SIPGATEWAYNAME = 'avaya.com'

ALWAYSSENDTOPROXY = 1

DISCONNECTONBROKENCONNECTION = 0

CDRSYSLOGSERVERIP = 192.168.62.24

ENABLEMWISUBSCRIPTION = 1

MWISERVERIP = '192.168.62.18'

MWIANALOGLAMP = 1

MWIDISPLAY = 1

ENABLEMWI = 1

ISFAXUSED = 1

SIPTRANSPORTTYPE = 2

REGISTRARNAME = 'avaya.com'

ENABLESIPS = 1

MEDIASECURITYBEHAVIOUR = 1

REGISTERONINVITEFAILURE = 1

REDUNDANTROUTINGMODE = 0

REGISTRARTRANSPORTTYPE = 2

MWISERVERTRANSPORTTYPE = 2

REREGISTERONCONNECTIONFAILURE = 1

SRTPOFFEREDSUITES = 1

[IPsec Params]

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

68 of 72

ACMP11xCM62SM62

[SNMP Params]

;

; *** TABLE DspTemplates ***

; This table contains hidden elements and will not be exposed.

; This table exists on board and will be saved during restarts

;

;

; *** TABLE TrunkGroup ***

;

;

[ TrunkGroup ]

FORMAT TrunkGroup_Index = TrunkGroup_TrunkGroupNum, TrunkGroup_FirstTrunkId,

TrunkGroup_FirstBChannel, TrunkGroup_LastBChannel,

TrunkGroup_FirstPhoneNumber, TrunkGroup_ProfileId, TrunkGroup_LastTrunkId,

TrunkGroup_Module;

TrunkGroup 0 = 1, 255, 1, 1, 54150, 0, 255, 255;

TrunkGroup 1 = 1, 255, 2, 2, 54050, 1, 255, 255;

TrunkGroup 2 = 2, 255, 3, 3, 3035383512, 0, 255, 255;

[ \TrunkGroup ]

;

; *** TABLE NumberMapIp2Tel ***

;

;

[ NumberMapIp2Tel ]

FORMAT NumberMapIp2Tel_Index = NumberMapIp2Tel_DestinationPrefix,

NumberMapIp2Tel_SourcePrefix, NumberMapIp2Tel_SourceAddress,

NumberMapIp2Tel_NumberType, NumberMapIp2Tel_NumberPlan,

NumberMapIp2Tel_RemoveFromLeft, NumberMapIp2Tel_RemoveFromRight,

NumberMapIp2Tel_LeaveFromRight, NumberMapIp2Tel_Prefix2Add,

NumberMapIp2Tel_Suffix2Add, NumberMapIp2Tel_IsPresentationRestricted,

NumberMapIp2Tel_SrcTrunkGroupID, NumberMapIp2Tel_SrcIPGroupID;

NumberMapIp2Tel 1 = xxxxxxxxxx#, *, *, 255, 255, 0, 0, 255, 91, , 255, -1, -

1;

[ \NumberMapIp2Tel ]

;

; *** TABLE PstnPrefix ***

;

;

[ PstnPrefix ]

FORMAT PstnPrefix_Index = PstnPrefix_DestPrefix, PstnPrefix_TrunkGroupId,

PstnPrefix_SourcePrefix, PstnPrefix_SourceAddress, PstnPrefix_ProfileId,

PstnPrefix_SrcIPGroupID, PstnPrefix_DestHostPrefix, PstnPrefix_SrcHostPrefix,

PstnPrefix_TrunkId;

PstnPrefix 0 = 54xxx, 1, *, *, 0, -1, *, *, -1;

PstnPrefix 1 = *, 2, *, *, 0, -1, *, *, -1;

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

69 of 72

ACMP11xCM62SM62

[ \PstnPrefix ]

;

; *** TABLE Dns2Ip ***

;

;

[ Dns2Ip ]

FORMAT Dns2Ip_Index = Dns2Ip_DomainName, Dns2Ip_FirstIpAddress,

Dns2Ip_SecondIpAddress, Dns2Ip_ThirdIpAddress, Dns2Ip_FourthIpAddress;

Dns2Ip 0 = avaya.com, 192.168.62.18, 0.0.0.0, 0.0.0.0, 0.0.0.0;

[ \Dns2Ip ]

;

; *** TABLE ProxyIp ***

;

;

[ ProxyIp ]

FORMAT ProxyIp_Index = ProxyIp_IpAddress, ProxyIp_TransportType,

ProxyIp_ProxySetId;

ProxyIp 0 = avaya.com:5061, 2, 0;

[ \ProxyIp ]

;

; *** TABLE TxDtmfOption ***

;

;

[ TxDtmfOption ]

FORMAT TxDtmfOption_Index = TxDtmfOption_Type;

TxDtmfOption 0 = 4;

[ \TxDtmfOption ]

;

; *** TABLE TrunkGroupSettings ***

;

;

[ TrunkGroupSettings ]

FORMAT TrunkGroupSettings_Index = TrunkGroupSettings_TrunkGroupId,

TrunkGroupSettings_ChannelSelectMode, TrunkGroupSettings_RegistrationMode,

TrunkGroupSettings_GatewayName, TrunkGroupSettings_ContactUser,

TrunkGroupSettings_ServingIPGroup, TrunkGroupSettings_MWIInterrogationType;

TrunkGroupSettings 0 = 1, 0, 0, , , -1, 255;

TrunkGroupSettings 1 = 2, 1, 0, , , -1, 255;

[ \TrunkGroupSettings ]

;

; *** TABLE TelProfile ***

;

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

70 of 72

ACMP11xCM62SM62

;

[ TelProfile ]

FORMAT TelProfile_Index = TelProfile_ProfileName, TelProfile_TelPreference,

TelProfile_CodersGroupID, TelProfile_IsFaxUsed, TelProfile_JitterBufMinDelay,

TelProfile_JitterBufOptFactor, TelProfile_IPDiffServ,

TelProfile_SigIPDiffServ, TelProfile_DtmfVolume, TelProfile_InputGain,

TelProfile_VoiceVolume, TelProfile_EnableReversePolarity,

TelProfile_EnableCurrentDisconnect, TelProfile_EnableDigitDelivery,

TelProfile_EnableEC, TelProfile_MWIAnalog, TelProfile_MWIDisplay,

TelProfile_FlashHookPeriod, TelProfile_EnableEarlyMedia,

TelProfile_ProgressIndicator2IP, TelProfile_TimeForReorderTone,

TelProfile_EnableDIDWink, TelProfile_IsTwoStageDial,

TelProfile_DisconnectOnBusyTone, TelProfile_EnableVoiceMailDelay,

TelProfile_DialPlanIndex, TelProfile_Enable911PSAP,

TelProfile_SwapTelToIpPhoneNumbers, TelProfile_EnableAGC,

TelProfile_ECNlpMode, TelProfile_DigitalCutThrough,

TelProfile_EnableFXODoubleAnswer, TelProfile_CallPriorityMode;

TelProfile 1 = "Modem Profile", 1, 1, 0, 10, 10, 46, 40, -11, 0, 0, 0, 0, 0,

1, 1, 1, 700, 1, -1, 255, 0, 0, 1, 1, -1, 0, 0, 0, 0, 0, 0, 0;

[ \TelProfile ]

;

; *** TABLE IpProfile ***

;

;

[ IpProfile ]

FORMAT IpProfile_Index = IpProfile_ProfileName, IpProfile_IpPreference,

IpProfile_CodersGroupID, IpProfile_IsFaxUsed, IpProfile_JitterBufMinDelay,

IpProfile_JitterBufOptFactor, IpProfile_IPDiffServ, IpProfile_SigIPDiffServ,

IpProfile_SCE, IpProfile_RTPRedundancyDepth, IpProfile_RemoteBaseUDPPort,

IpProfile_CNGmode, IpProfile_VxxTransportType, IpProfile_NSEMode,

IpProfile_IsDTMFUsed, IpProfile_PlayRBTone2IP, IpProfile_EnableEarlyMedia,

IpProfile_ProgressIndicator2IP, IpProfile_EnableEchoCanceller,

IpProfile_CopyDest2RedirectNumber, IpProfile_MediaSecurityBehaviour,

IpProfile_CallLimit, IpProfile_DisconnectOnBrokenConnection,

IpProfile_FirstTxDtmfOption, IpProfile_SecondTxDtmfOption,

IpProfile_RxDTMFOption, IpProfile_EnableHold, IpProfile_InputGain,

IpProfile_VoiceVolume, IpProfile_AddIEInSetup,

IpProfile_SBCExtensionCodersGroupID, IpProfile_MediaIPVersionPreference,

IpProfile_TranscodingMode, IpProfile_SBCAllowedCodersGroupID,

IpProfile_SBCAllowedCodersMode, IpProfile_SBCMediaSecurityBehaviour,

IpProfile_SBCRFC2833Behavior, IpProfile_SBCAlternativeDTMFMethod,

IpProfile_SBCAssertIdentity, IpProfile_AMDSensitivityParameterSuit,

IpProfile_AMDSensitivityLevel, IpProfile_AMDMaxGreetingTime,

IpProfile_AMDMaxPostSilenceGreetingTime, IpProfile_SBCDiversionMode,

IpProfile_SBCHistoryInfoMode;

IpProfile 1 = "Modem Profile", 1, 0, 0, 10, 10, 46, 40, 0, 0, 0, 0, 2, 0, 0,

0, 1, -1, 1, 0, 1, -1, 0, 4, -1, 1, 1, 0, 0, , -1, 0, 0, -1, 0, 0, 0, 0, -1,

0, 8, 300, 400, -1, -1;

[ \IpProfile ]

;

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

71 of 72

ACMP11xCM62SM62

; *** TABLE TargetOfChannel ***

;

;

[ TargetOfChannel ]

FORMAT TargetOfChannel_Index = TargetOfChannel_Destination,

TargetOfChannel_Type, TargetOfChannel_HotLineToneDuration;

TargetOfChannel 2 = 54150, 1, -1;

[ \TargetOfChannel ]

;

; *** TABLE ProxySet ***

;

;

[ ProxySet ]

FORMAT ProxySet_Index = ProxySet_EnableProxyKeepAlive,

ProxySet_ProxyKeepAliveTime, ProxySet_ProxyLoadBalancingMethod,

ProxySet_IsProxyHotSwap, ProxySet_SRD, ProxySet_ClassificationInput,

ProxySet_ProxyRedundancyMode;

ProxySet 0 = 1, 600, 0, 0, 0, 0, -1;

[ \ProxySet ]

;

; *** TABLE CodersGroup0 ***

;

;

[ CodersGroup0 ]

FORMAT CodersGroup0_Index = CodersGroup0_Name, CodersGroup0_pTime,

CodersGroup0_rate, CodersGroup0_PayloadType, CodersGroup0_Sce;

CodersGroup0 0 = g711Alaw64k, 20, 0, -1, 0;

CodersGroup0 1 = g711Ulaw64k, 20, 0, -1, 0;

CodersGroup0 2 = g729, 20, 0, -1, 0;

[ \CodersGroup0 ]

;

; *** TABLE CodersGroup1 ***

;

;

[ CodersGroup1 ]

FORMAT CodersGroup1_Index = CodersGroup1_Name, CodersGroup1_pTime,

CodersGroup1_rate, CodersGroup1_PayloadType, CodersGroup1_Sce;

CodersGroup1 0 = g711Ulaw64k, 20, 0, -1, 0;

CodersGroup1 1 = g711Alaw64k, 20, 0, -1, 0;

[ \CodersGroup1 ]

KJA; Reviewed;

SPOC 7/6/2012

Solution & Interoperability Test Lab Application Notes

©2012 Avaya Inc. All Rights Reserved.

72 of 72

ACMP11xCM62SM62

©2012 Avaya Inc. All Rights Reserved.

Avaya and the Avaya Logo are trademarks of Avaya Inc. All trademarks identified by ® and

™ are registered trademarks or trademarks, respectively, of Avaya Inc. All other trademarks

are the property of their respective owners. The information provided in these Application

Notes is subject to change without notice. The configurations, technical data, and

recommendations provided in these Application Notes are believed to be accurate and

dependable, but are presented without express or implied warranty. Users are responsible for

their application of any products specified in these Application Notes.

Please e-mail any questions or comments pertaining to these Application Notes along with the

full title name and filename, located in the lower right corner, directly to the Avaya

DevConnect Program at [email protected].